heterogeneous photocatalytic degradation of … n1 2014 pp 31-45.pdfheterogeneous photocatalytic...

South African Journal of Chemical Engineering, vol. 19, 2014, no. 1, pp 31-45 31

Heterogeneous Photocatalytic Degradation of Naphthalene using Periwinkle Shell Ash: Effect of Operating Variables, Kinetic and

Isotherm Study

Aisien Felixa, Amenaghawon Andrew

b, Assogba Mededode

c

a,b,c University of Benin, Chemical Engineering Department

Keywords: Photocatalysis, Periwinkle shell ash, Naphthalene, Kinetics, Adsorption capacity

Abstract-This study investigated the potential use of low cost photocatalyst, Periwinkle shell

ash (PSA) for the batch photocatalytic degradation of naphthalene in aqueous solutions. The

effect of contact time, initial naphthalene concentration, PSA dosage, presence of electron

accepting oxidant (H2O2), and the pH of solution on the percentage photodegradation of

naphthalene determined. For the treatment conditions considered in this study, the optimum

values were obtained to be: contact time, 210 minutes; initial naphthalene concentration, 25

mg/L; PSA dosage, 2 g; pH, 9. The addition of Hydrogen Peroxide (H2O2) enhanced the

photodegradation process with almost 100 percent degradation achieved. The adsorption

equilibrium data fitted well to the Langmuir isotherm equation (R2=0.993) indicating mono

layer type adsorption while the kinetics of the process was well described by the Langmuir-

Hinshelwood kinetic model with high correlation coefficient value (R2=0.998). This study has

demonstrated that the low cost photocatalyst, PSA can be used for removal of naphthalene

from aqueous solution. Also the kinetic information obtained can be used for designing

treatment systems for naphthalene abatement.

INTRODUCTION

The scale of environmental pollution and particularly water pollution in the world today has prompted engineers

and scientists to focus attention on cleaner and more environmentally friendly processes (Abdollahi et al., 2011).

Naphthalene is an important polycyclic aromatic hydrocarbon (PAH) which enters the environment through

various sources such as incomplete combustion of gasoline and diesel in internal combustion engines,

combustion of coal and oil for power generation, wood burning, tobacco smoking, fumigants etc (Jia and

Batterman, 2010; Li et al., 2010; Wilson et al., 2003). As a result of it relatively higher solubility compared to

other PAHs, it can be readily mobilised into the aqueous phase through discharges from industrial and domestic

effluents, leaks of PAHs containing materials, used oil, bilge water, runoff from paved roads, parking lots etc

(Alamo-Nole et al., 2011; Lair et al., 2008).

Exposure to naphthalene is considered to be carcinogenic, toxic and mutagenic to humans with both acute and

chronic effects on health; hence it has been listed as a priority environmental pollutant by many countries

(ATSDR, 2005; Henner et al., 1997; Lair et al., 2008). Removal of naphthalene from aqueous solutions can be

accomplished by various methods including electron beam irradiation (Cooper et al., 2002), biodegradation

using surfactants (Liu et al., 1995), ozonolysis (Legube et al., 1986), adsorption using zeolites and activated

carbon (Ania et al., 2007; Chang et al., 2004) and photocatalytic degradation using Titanium dioxide (TiO2) and

Zinc oxide (ZnO) (Lair et al., 2008; Zhou et al., 2012).

Photocatalysis is a promising technique for the degradation of organic pollutants in aqueous media. It is based

on the surface activation of semiconductors notably ZnO and TiO2 by ultraviolet (UV) radiation. Perhaps the

most significant advantage of this technique is that it can be used to degrade most organic compounds which are

not amenable to other conventional treatment processes. It is faster than most bioprocesses and cheaper than

ozonolysis and radiation based processes as it can be carried out under direct sunlight, making it able to operate

independent of any external power source (Lair et al., 2008).

Woo et al. (2009) studied the photocatalytic degradation of some PAHs namely naphthalene, acenaphthylene,

phenanthrene, anthracene, and benzo[a]anthracene. These PAHs typically have low solubility in aqueous

medium hence they investigated the effect of acetone on the photocatalytic degradation efficiency. They

reported that addition of 16% acetone greatly enhanced the efficiency of the process with all of the PAHs

degraded within a 24 hour period using TiO2. Gautam et al. (2005) studied the photocatalytic degradation of 4-

nitroaniline using solar and artificial UV radiation in the presence of TiO2 suspensions in a batch and continuous

annular reactor. They observed that catalyst loading, pH, initial concentration and the presence of anions

influenced the rate of photocatalytic degradation. They further reported that P-Aminophenol, p-benzoquinone


and hydroquinone were the intermediates during the degradation process. Wu et al. (2008) studied the

photocatalytic degradation of terbufos in aqueous suspensions using TiO2. They reported that various

operational variables such as catalyst loading, pH, and the presence of anions affected the rate of degradation

with about 99% of terbufos degraded within 90 minutes. Vasconcelos et al. (2009) reported results on the

performance of heterogeneous photocatalytic degradation, photo-induced oxidation, ozonation and peroxone in

degrading the fluoroquinolone antimicrobial ciprofloxacin (CIP) in a hospital effluent. They reported that both

heterogeneous photocatalytic degradation and peroxone led to almost complete CIP degradation after one hour

of treatment.

From these studies, it was observed that photocatalytic degradation is fast and efficient and conventional

catalyst such as TiO2 is typically used in the presence of UV light. The use of TiO2 in photocatalysis is highly

evident in degrading organic pollutants in wastewater, sludges and contaminated soils due to its high activity,

stability under irradiation, reliability, low cost and availability (Ahmed et al., 2011). Despite these attractive

characteristics, the commercial application of TiO2 for the photocatalytic degradation of liquid wastes is limited

by the recovery potential of the catalyst and economic viability of the process with respect to the efficiency in

the use of radiation. As a result of these limitations, researchers have focused attention on the development of

photocatalysts with better recovery and light absorption capacity. Hence, focus will be on replacement of the

commercial catalysts with locally sourced catalysts such as periwinkle shell ash. Periwinkle shell is a waste

product generated from the consumption.

periwinkle, a small greenish-blue marine snail housed in a V shaped spiral shell. It is found in many coastal

communities within Nigeria (Olutoge et al., 2012). After consumption of the edible part as sea food, the shell is

typically disposed off as waste thereby constituting environmental problems. Although some research work

have focused on utilising the shell as coarse aggregate in concrete, manufacture of break pads, as paving of

water logged areas e.t.c., yet a large amount of these shells are still disposed resulting in the need to find other

means of improving upon the reuse capacity of these shells (Aku et al., 2012).

The aim of this study therefore is to evaluate the potential use of periwinkle shell ash (PSA) for the

photocatalytic degradation of naphthalene in aqueous solution. The effects of factors such as contact time, initial

naphthalene concentration, catalyst dosage, pH, and amount of oxidant (Hydrogen peroxide, H2O2) on the

degradation process was investigated. The photocatalytic degradation of naphthalene was further evaluated by

carrying out kinetic (pseudo-first-order, pseudo-second-order, intra particle diffusion and Langmuir-

Hinshelwood models) and isotherm studies (using common isotherms such as Langmuir, and Freundlich

isotherms).

MATERIALS AND METHODS

Preparation and Characterisation of Adsorbent (Periwinkle shell ash)

Periwinkle shells were obtained from Evbuobanosa in Edo State of Nigeria. They were washed and dried in an

oven at 110°C to constant mass, followed by crushing, then calcined at 600°C in a muffle furnace. The

calcination was carried out in such a way that neither the fuel for heating not the fire gases came in contact with

the material that was being calcined. It was thereafter sieved to obtain fine particles (< 350Hm) of periwinkle

shell ash (PSA). The prepared PSA was characterized by determining the composition using X-Ray

Fluorescence (XRF) analysis. Complete mineralogical analysis was carried out by X-ray diffraction (XRD) to

determine the ultimate elemental composition of the PSA using a Philips X-ray diffractometer (Aku et al.,

2012). Fourier transform infrared spectrometry (FTIR) was also carried out on the PSA. The IR spectra of the

PSA were recorded using Perkin Elmer spectrum 100 FT–IR spectrometer in the frequency range 4000 to 400

cm-1

, operating in ATR (attenuated total reflectance) mode. The surface structure and other properties of the

PSA were evaluated by nitrogen adsorption method at -196ºC (Aisien et al., 2013). Nitrogen adsorption

isotherms were determined using an adsorption equipment (BET 624, Micro-meritics, Germany). The surface

area of the PSA was determined using the standard BET equation. The bulk density of the PSA was determined

following standard methods (APHA-AWWA-WPCF, 1989).

Preparation of Adsorbate

Analytical reagent grade naphthalene, provided by Griffin and George Ltd, Loughborough, England was used as

the representative PAH. A stock solution of naphthalene was prepared by dissolving 1 g of naphthalene in 1L of

a binary solution comprising 50 mL of methanol (British Drug Houses Ltd, England) and 950 mL of deionised

water. Naphthalene is a hydrophobic compound with low solubility in water. The water-methanol solution was


used instead of pure deionised water to enhance the solubility of hydrophobic naphthalene (Agarry et al., 2013;

Chang et al., 2004). Working solutions with different concentrations of naphthalene were prepared by

appropriate dilutions of the stock solution with distilled water immediately prior to their use.

Analysis of Naphthalene in Aqueous Solution

A UV-Vis spectrophotometer (PG Instruments model T70) was used to determine the concentration of

undegraded naphthalene in the aqueous medium at a wavelength of 226 nm. The pH of the aqueous medium was

adjusted using 0.5 M HCl and 0.1 M NaOH solutions.

Batch Study of the Photocatalytic Degradation of Naphthalene

Batch photocatalytic degradation of naphthalene using PSA in the presence of UV radiation from sunlight was

carried out in mechanically agitated 250 mL jacketed glass flasks with a working volume of 100 mL. Two

grams (2 g) of PSA was added to the aqueous solution of naphthalene of the desired concentration. For all

studies, the suspensions were magnetically stirred without any permanent air bubbling. The temperature was

maintained at 20oC and monitored throughout the process (Lair et al., 2008). The effects of contact time, initial

naphthalene concentration, PSA dosage, amount of oxidant and pH of solution on the degradation efficiency

were investigated. At the end of each experiment the agitated solution mixture was filtered through a 0.45 μm

membrane and the residual concentration of naphthalene was determined spectrophotometrically. The

percentage photocatalytic degradation of naphthalene was calculated using the equation.

% Photodegradation = 𝐶𝑜− 𝐶𝑡

𝐶𝑜 x 100 (1)

where Co and Ct are the initial and the liquid-phase concentration of naphthalene at time t, respectively.

RESULTS AND DISCUSSION

Characterisation of PSA

PSA is a very complex material in terms of chemical composition as it contains a lot of chemical compounds

typically oxide of metals. The chemical composition of PSA as obtained from X-Ray Fluorescence (XRF)

analysis is presented in Table 1

Table 1: Chemical composition of PSA

Chemical Component Composition (wt%)

MgO 1.2

SiO2 33.2

ZnO 3.2

Fe2O3 5.0

MnO2 1.0

Al2O3 9.2

CaO 41.3

CuO 1.03

K2O 1.4

Na2O 1.38

TiO2 0.02

on Ignition 1.8

The results of complete mineralogical analysis as carried out by X-ray diffraction (XRD) to determine the

ultimate elemental composition of the PSA is presented in Table 2. The major constituent of the PSA used in

this study was calcium oxide (CaO) which accounted for 41.3% of the weight of PSA characterised. This was

followed by silica, aluminium oxide and Iron oxide which accounted for about 33.2, 9.2 and 5% respectively as

shown in Table 1. Some other oxides such as K2O, Na2O, TiO2 and MnO2 were also found to be present in

small amounts. XRD results obtained for ultimate elemental composition indicate that the major element found

in PSA is iron (Fe) which accounted for about 19.2% of the weight of PSA characterised. This was followed by


Zinc (Zn) and Nickel (Ni) which accounted for about 16.5 and 9% respectively as shown in Table 2. Some of

the oxides and elements presented in Tables 1 and 2 have been established to possess photocatalytic properties

thus supporting the choice of PSA for this study.

Table 2: Ultimate elemental composition of PSA

Chemical Component Composition (wt%)

Fe 19.20

Cr 6.30

V 1.50

Ni 9.00

Se 0.13

Pb 0.08

Al 12.30

Zn 16.50

Sn 8.00

Cd 0.05

Cu 2.40

Table 3: Physical properties of PSA

Property Value

Surface area (m2/g) 400

Bulk density (kg/m3) 2940

Porosity (-) 0.004

The surface area, bulk density, and porosity of the PSA used in this study are presented in Table 3. The results

presented in Tables 1, 2 and 3 are similar to those reported in the literature (Kosmatka et al., 2003; Owabor and

Iyaomolere, 2013; Umoh and Olusola, 2012).

The pattern of naphthalene uptake by PSA may be attributed to the active groups and bonds present in the

photocatalyst (Nagarajan et al., 2013). The result of FTIR analysis of the PSA in the range 350 to 4400 cm-1

is

shown in Figure 1. Peaks in the range of 3100 to 3500 cm-1

is indicative of the presence of OH groups and the

stretching of the N-H bond of the amino group (Park et al., 2005). Absorption bands in the range of 2700 to

1430 cm-1

and 900 to 1380 cm-1

are indicative of the presence of phenyl groups and the stretching of the C-O

bond in carboxylic groups present in the PSA.

Fig. 1: FTIR spectra of periwinkle shell ash


Effect of contact time on the photocatalytic degradation of naphthalene

The profile of time dependent study of photocatalytic degradation of naphthalene by PSA in the presence of UV

from sunlight is shown in Figure 2. It can be observed from the Figure that the degradation process was rapid for

the first 150 minutes as indicated by the steep increase in the percentage degradation of naphthalene. The rate of

photocatalytic degradation continues to increase but less rapidly for the next 60 minutes and the profile levels

off thereafter indicating that equilibrium has been reached. At equilibrium, all available active sites on the PSA

particles are occupied by the naphthalene molecules which leads to saturation hence no noticeable increase in

degradation is observed. The rapid rate of photodegradation observed at the initial stage of the process may be

attributed to the abundant availability of active sites on the surface of the PSA. These sites are later occupied by

the naphthalene molecule as the process progresses consequently leading to the slow degradation rate observed

in the later part of the process (Amenaghawon et al., 2013; Mahvi et al., 2004). An equilibrium time of 100

minutes was reported by Woo et al. (2009) for the photocatalytic removal of naphthalene from aqueous solution

using Titanium dioxide (TiO2) in the presence of UV light. Abdollahi et al. (2011) reported an equilibrium

contact time of 240 minutes for the photodegradation of m-cresol by Zinc Oxide using visible light irradiation.

Effect of initial naphthalene concentration on the photocatalytic degradation of naphthalene

The concentration of pollutant is a very important variable during any abatement process. The effect of the

initial concentration of naphthalene on the photodegradation efficiency is presented in Figure 3. The results

show that increasing the concentration of naphthalene resulted in a decrease in the percentage degradation of

naphthalene by PSA. At an initial concentration of 25 mg/L, there was about 90% photodegradation of

naphthalene while the photodegradation reduced to about 60% at an initial concentration of 150 mgL-1

.

Fig. 2: Effect of contact time on the photocatalytic degrdation of naphthalene by PSA (pH 9; PSA dose, 2 g;

initial concentration, 25 mgL-1

; Temperature, 20oC)

Fig. 3: Effect of initial concentration on the photocatalytic degrdation of naphthalene by PSA (pH 9; PSA dose,

2 g; Temperature, 20oC)


The trend observed can be explained by the fact that at high concentrations of naphthalene, the active sites on

the PSA are occupied by the naphthalene molecules and its intermediates thereby leading to reduced generation

of the electron-hole pair (e--h

+) which consequently reduces the photodegradation efficiency (Abdollahi et al.,

2011; Konstantinou and Albanis, 2004). Another reason could be that with every other variable held constant

while the initial naphthalene concentration is increased, the amount of hydroxyl and oxygen (•OH and O2 2-

) free

radicals formed on the surface of the PSA is also constant. Hence the relative ratio of these radicals available for

attacking the naphthalene molecules decreases and the photodegradation efficiency consequently decreases

(Lathasree et al., 2004; Rana and Sharma, 2010).

Effect of PSA dosage on the photocatalytic degradation of naphthalene

The result of the investigation of the effect of PSA dosage on the photocatalytic degradation of naphthalene is

presented in Figure 4. The percentage degradation of naphthalene initially increased with increase in PSA

dosage up to a maximum value of about 90% at a PSA dosage of 2 g. Further increase in PSA dosage resulted in

a decrease in the percentage degradation of naphthalene. The initial increase in percentage degradation of

naphthalene observed could be attributed to the fact that increasing the amount of PSA increases the number of

active sites on the PSA surface which in turn increases the number of free radicals (•OH and O2 2-

) consequently

leading to enhanced photodegradation of naphthalene (Inamdar and Singh, 2008). Furthermore, more of the

naphthalene molecules were removed from the solution by adsorption as a result of the increase in the dosage of

PSA.

Fig. 4: Effect of PSA dosage on the photocatalytic degrdation of naphthalene by PSA (pH 9; initial

concentration, 25 mgL-1

; Temperature, 20oC)

Fig. 5: Effect of pH on the photocatalytic degrdation of naphthalene by PSA (Initial concentration, 25 mgL-1

PSA dose, 2 g; Temperature, 20oC)


The decrease in photodegradation efficiency observed beyond the optimum PSA dosage might have been as a

result of some factors. These factors include increased opacity of the aqueous medium and enhancement of the

light reflectance as a result of the excess of PSA particles, agglomeration and sedimentation of the PSA particles

is possible at high PSA dosage, thus making a fraction of the PSA surface inaccessible for radiation absorption

and consequently resulting in a decrease in the degradation of the naphthalene molecules (Abdollahi et al., 2011;

Konstantinou and Albanis, 2004; Rana and Sharma, 2010).

Effect of pH on the photocatalytic degradation of naphthalene

The effect of pH on the photocatalytic degradation of naphthalene by PSA is presented in Figure 5. The pH of

the aqueous medium is important in that it controls the surface charge properties of the photocatalyst (Abdollahi

et al., 2011). It also affects the production of hydroxyl radicals which are powerful oxidizing agents (Rana and

Sharma, 2010). The percentage degradation of naphthalene initially increased with increase in pH up to a

maximum value of about 92 % at a pH of 9. Further increase in pH did not result in an increase in the

percentage degradation of naphthalene. Similar observations have been reported by Qamar et al. (2005) for the

photocatalysed degradation of two selected azo dye derivative in aqueous suspension as well as Abdollahi et al.

(2011) for the photodegradation of m-cresol by Zinc Oxide under visible-light irradiation. The initial increase in

percentage degradation of naphthalene observed could be attributed to the increase in the adsorption of

naphthalene on the PSA surface which results from a decrease in the electrostatic repulsive forces and increased

interaction between photocatalyst surface and naphthalene molecules (Kosmulski, 2006). Additionally, in

alkaline solutions, the hydroxyl ions (OH-) are readily generated. When a hole is generated by the photocatalyst,

an electron is abstracted from the OH- ions converting it into hydroxyl radicals (•OH) which are responsible for

the photodegradation of naphthalene (Menkiti et al., 2009). However, beyond the pH value of 9, the

photodegradation efficiency was observed to decrease. This could be attributed to the fact that at high pH values

and consequently high hydroxyl ions (OH-) concentrations, the rate at which the hydroxyl radicals (•OH) are

used up is accelerated resulting in a decrease in the photodegradation efficiency (Abdollahi et al., 2011). In

addition, the abundant hydroxyl ions (OH-) generated at high pH values will compete with the electron rich

naphthalene for adsorption on the PSA surface. The hydroxyl ions (OH-) will make the PSA surface to be

negatively charged and as a result, the approach of the naphthalene molecules to the PSA surface will be slowed

because of the repulsive force between the hydroxyl ions (OH-) and the naphthalene molecules thereby leading

to a decrease in the photodegradation efficiency (Kothari et al., 2007).

Effect of oxidant dosage on the photocatalytic degradation of naphthalene The effect of hydrogen peroxide (H2O2) on the photocatalytic degradation of naphthalene by PSA is illustrated

in Figure 6. Generally, it can be observed that the percentageage degradation of naphthalene increased with

increase in the amount of oxidant used. Almost 100% degradation of naphthalene was recorded when 10 cm3 of

hydrogen peroxide was used. The trend observed may be due to the oxidative effect of hydrogen peroxide. The

effect of H2O2 has been the subject of many studies and it has been established that it increases the

photodegradation rates of organic pollutants (Hallamn, 1992). Hydrogen peroxide which is an electron acceptor

is known to generate hydroxyl radicals by the mechanisms shown in equation (2). H2O2 is a better electron

acceptor than molecular oxygen based on their respective one-electron reduction potentials.

H2O2 + 𝑒−→ OH + − OH (2)

Fig. 6: Effect of oxidant (H2O2) loading on the photocatalytic degrdation of naphthalene by PSA (pH, 9; initial

concentration, 25 mg/L PSA dose, 2 g; Temperature, 20oC)


The increase in percentage degradation of naphthalene observed when the amount of H2O2 was increased may

be attributed to some factors which include the ability of H2O2 to remove the electrons trapped on the surface of

the PSA thereby lowering the electron-hole recombination rate and consequently improving the utilisation of

holes in the production of the hydroxyl radicals (•OH). In addition H2O2 can also cleave in the presence of UV

radiation to directly produce the hydroxyl radicals (•OH). Lastly, rapid oxygen consumption or passive oxygen

mass transfer in the liquid phase may result to that phase being depleted of oxygen, hence H2O2 addition

alleviates this problem. The free radicals formed from the addition of H2O2 create a strong oxidation

environment which favours the photocatalytic degradation of naphthalene.

Kinetics of Photodegradation of Naphthalene The kinetics of photodegradation was studied for its important function in the treatment of naphthalene

contaminated aqueous systems. Four kinetic models namely Lagergren pseudo first order, pseudo second-order,

intra particle diffusion and Langmuir-Hinshelwood kinetic models were used to elucidate the mechanism of the

degradation process.

Pseudo-first order model The Lagergren pseudo first order kinetic model (Lagergren, 1898) has been widely used to describe the

kinetics of heterogeneous treatment processes. It is expressed in its integrated linear form in Equation (3).

ln(qe -qt) = ln(qe - klt) (3)

where qe and qt (mg/g) are adsorption capacity at equilibrium and at time t, respectively, k1 is the rate constant of

pseudo first order adsorption (min-1). The values of ln(qe – qt) were linearly correlated with t. The plot of ln(qe –

qt) versus t resulted in a linear relationship from which k1 and qe was determined from the slope and intercept

respectively as shown in Figure 7. The first order rate constants calculated from the plot are given in Table 4. A

linear relationship observed in the semi-log plot is indicative of the applicability of the model and the first order

of the process.

Pseudo-second order model

The pseudo-second order kinetic model which assumes that chemisorption is the rate determining step can be

expressed in its integrated linear form as in Equation (4).

𝑡

𝑞𝑡=

1

𝑘2𝑞𝑒2 +

1

𝑞𝑒t (4)

The initial adsorption rate, h (mg.g-1

.min-1

) is expressed as follows:

ℎ = 𝑘2𝑞𝑒2 (5)

Where k2 is the rate constant of the pseudo second order process (g.mg-1.min-1). The plot of (t/qt) and t of

Equation (4) is shown in Figure 8. The kinetic constants calculated from the plot are shown in Table 4. It can be

observed that the model did not fit the experimental data. This indicates that the model was not able to describe

the mechanism of the process.


Fig. 7: Pseudo first order model fitted to batch equilibrium data for naphthalene photodegradation by PSA (pH,

9; initial concentration, 25 mgL-1


Fig. 8: Pseudo second order model fitted to batch equilibrium data for naphthalene photodegradation by PSA

(pH, 9; initial concentration, 25 mgL-1


Intra particle diffusion model

The intra particle diffusion kinetic model (Weber and Morris, 1963) was fitted to the batch equilibrium data to

elucidate the diffusion mechanism. The model equation is presented in Equation (6).

qt = kpt1/2

+ c (6)

Where Kp is the intra particle diffusion rate constant (mgg-1

min-1/2

) and C is an indication of boundary layer

effect. The larger the intercept, the greater is the contribution of the surface sorption in the rate controlling step.

The calculated values of the intra particle diffusion rate constant and the boundary layer thickness are presented

in Table 4. The plot of qt vs t1/2

as presented in Figure 9 indicates the existence (although not significant) of

some boundary layer effect and further showed that intra particle diffusion was not the only rate limiting step.

Langmuir-Hinshelwood model

The Langmuir–Hinshelwood kinetic equation has been applied severally to the analysis of heterogeneous

photocatalytic reactions (Bianco-Prevot et al., 2001; Houas et al., 2001; Lachheb et al., 2002; Stylidi et al.,

2003).

r = 𝑘𝐾𝐶

1+𝐾𝐶 (7)

where r is the degradation rate of the pollutant (mg/L.min), C the concentration of the pollutant (mg/L), t the

irradiation time, k the reaction rate constant (mg/L.min), and K is the adsorption coefficient of the pollutant

(L/mg). The values of the calculated constants are presented in Table 4. A linear expression was obtained by

plotting the reciprocal initial rate against the reciprocal initial concentration (Figure 10).


Fig. 9: Intra particle diffusion model fitted to batch equilibrium data for naphthalene

photodegradation by PSA (pH, 9; initial concentration, 25 mgL-1


Fig. 10: Langmuir-Hinshelwood model fitted to batch equilibrium data for

naphthalene photodegradation by PSA (pH, 9; PSA dose, 2 g; Temperature, 20oC)

In conclusion, Table 4 shows that the tested kinetic models fitted well to the kinetic data with high correlation

coefficients with the exception of the pseudo second order model. However, the Langmuir-Hinshelwood

resulted in the best fit with highest correlation coefficient to describe the adsorption behaviour of naphthalene

onto PSA.

Table 4: Kinetic constant parameter values for the photodegradation of naphthalene by PSA

Kinetic Model Parameters Values

Lagergren Pseudo First-Order k1 (min-1)

qe (mg/g)

0.626

1.116

R2 0.972

qe (mg/g) -3.049

R2 0.340

Intra particle diffusion Kp (mg/g/min1/2) 0.352

C (mg/g) 0.003

R2 0.986

Langmuir-Hinshelwood k (mgL-1.min) 333.333

K (Lmg-1) 0.00102

R2 0.998

Isotherm Studies Isotherm studies were carried out to explore the relationship between naphthalene uptake (qe) and its

equilibrium concentration in the solution (Ce). Equilibrium data was analysed using adsorption isotherms which

are helpful in determining the adsorption capacity of PSA for naphthalene. The Langmuir and Freundlich

adsorption isotherm models were used to analyze the equilibrium data for the photodegradation of naphthalene


using PSA. The curves of the related adsorption isotherms were regressed and parameters of the equations were

thus obtained.

Langmuir isotherm

The Langmuir isotherm model (Langmuir, 1914) has been used empirically because it contains the two useful

parameters (qo and KL), which reflect the two important characteristics of the sorption system. It assumes that

the adsorption process is of the monolayer type which indicates that the adsorbate is adsorbed onto a surface

with finite number of sites which are homogeneously distributed over the surface of the adsorbent (Agarry and

Aremu, 2012). The Langmuir isotherm equation is given as:

qe= 𝑞𝑜𝐾𝑙𝐶𝑒

1+𝐾𝑙𝐶𝑒 ( 8)

qo is the maximum sorption capacity (mg/g) of the adsorbent while KL is the sorption constant (L/mg) at a given

temperature. The parameters of the Langmuir isotherm equation were obtained by fitting the equation directly to

the equilibrium data using the non-linear curve fitting tool of MATLAB 7.0 software package. The shape

obtained for the isotherm is shown in Figure 11. The values of the Langmuir isotherm parameters as well as the

correlation coefficient (R2) of the Langmuir equation for the photodegradation of naphthalene by PSA are given

in Table 6. The values of these parameters were close to those reported by Agarry et al. (2013) and Tsyntsarski

et al. (2011) for the adsorption of naphthalene by spent tea leaves and activated carbon produced from biomass

and coal wastes respectively.

The essential characteristics of the Langmuir isotherm model can also be explained in terms of a dimensionless

constant referred to as the separation factor (RL) defined in Equation (9) (Anirudhan and Radhakrishnan, 2008;

Annadurai et al., 2007).

Rl= 𝑞𝑜𝐾𝑙𝐶𝑒

1+𝐾𝑙𝐶𝑜 (9)

Co is the initial concentration of naphthalene. The value of the separation factor determines the nature of

adsorption as follows: RL > 1 unfavourable, RL = 1 linear, 0<RL<1 favourable and RL = 0

irreversible. For this study, the values of RL given in Table 5 are between zero and one indicating that the

adsorption was favourable.

Table 5: RL values and type of isotherm

Initial concentration(mg/L) RL Value

25 0.739

50 0.587

75 0.486

100 0.415

125 0.362

150 0.321

Freundlich isotherm

The Freundlich isotherm is an empirical equation employed to describe heterogeneous systems. The Freundlich

equation is expressed as:

qe = Kf (Ce)

1/n (10)

Table 6: Kinetic parameters for Langmuir and Freundlich isotherms

Langmuir isotherm Freundlich isotherm

qo (mg/g) KL (L/mg) R2 Kf (mg/g) n R

2

12.346 0.0141 0.993 0.225 1.225 0.968


Figure 11: Langmuir isotherm model fitted to batch equilibrium data for naphthalene photodegradation by PSA

(pH, 9; PSA dose, 2 g; Temperature, 20oC)

Figure 12: Freundlich isotherm model fitted to batch equilibrium data for naphthalene

photodegradation by PSA (pH, 9; PSA dose, 2 g; Temperature, 20oC)

The high values of the correlation coefficients as shown in Table 6 indicates that the data conformed well to

both isotherm equations; however, a better fit resulted for the case of Langmuir isotherm equation as seen in the

higher value of the correlation coefficient. Values of Kf and n have been reported by various researchers on

adsorption of naphthalene. Pal (2012) reported Kf and n values of 0.3 and 1.12, 0.025 and 1.47 for the adsorption

of naphthalene by sugarcane bagasse and rice husk respectively. Agarry et al. (2013) reported Kf and n values

2.44 and 1.85 respectively for the adsorption of naphthalene on spent tea leaves. Therefore the constants

obtained in this study are comparable to those reported by previous researchers. The difference could be as a

result of difference in the range of concentration, type of material used, pH, temperature and properties of the

adsorbent such as functional groups present on the surface, surface area, pore structure, etc (Agarry and Aremu,

2012). The shape of the adsorption isotherm presented in Figure 11 indicates that it belongs to the L2 category

of isotherm which is the Langmuir type of adsorption (Annadurai et al., 1997). Agarry and Aremu, (2012)

reported that this type of isotherm is usually met with when the adsorbate is strongly attracted to the surface of

the adsorbent.

Intermediates of Naphthalene Degradation Determination of the some intermediate photoproducts of naphthalene photodegradation was carried out by GC-

MS analysis. Results of the analyses revealed a series of peaks at different retention times. The degradation of

naphthalene progressed through the formation of several intermediates as shown in Table 7. The most abundant

of these was 2-formylcinnamaldehyde with a retention time of 21.1 minutes. This compound was also identified

by other researchers as an intermediate degradation product of naphthalene (Lair et al., 2008; Pramauro et al.,

1998). Aside from this, 5-Hydroxy-l,4- naphthoquinone, and naphthols were also present in high amounts

(Hykrdová et al, 2002). Other compounds, 1,2-benzenedicarboxylic acid, phthalic acid, and 1,4-Naphthoquinone

were also present though in smaller amounts.


Table 7: Reaction intermediates indentified by GC-MS

Degradation product Retention time (min)

2-Formylcinnamaldehyde 21.1

1-Naphthol 20.7

2-Naphthol 20.8

1,4-Naphthoquinone 19.4

5-Hydroxy-l,4-naphthoquinone 20.9

1,2-benzenedicarboxylic acid 16.6

phthalic acid 21.0

CONCLUSIONS

The batch photodegradation of naphthalene in aqueous medium using periwinkle shell ash in the presence of

UV from sunlight was investigated. Photodegradation of naphthalene by PSA is influenced by factors such as

contact time, initial naphthalene concentration, PSA dosage, presence of oxidant and solution pH. For the

conditions considered in this study, the optimum values obtained are as follows: contact time, 210 minutes;

initial naphthalene concentration, 25 mg/L; PSA dosage, 2 g; pH, 9. The addition of electron accepting oxidant

(H2O2) enhanced the photodegradation process with almost 100 percent degradation achieved. The adsorption

equilibrium data fitted well to the Langmuir isotherm equation indicating mono layer type adsorption while the

kinetics of the process was well described by the Langmuir-Hinshelwood kinetic model with high correlation

coefficient value. This study has demonstrated that the low cost photocatalyst, PSA from waste materials can be

used for removal of naphthalene from aqueous solution. Also the kinetic information obtained can be used for

designing economically viable treatment systems for naphthalene abatement

REFERENCES

1. Abdollahi, Y., Abdullah, A.H., Zainal, Z. and Yusof, N.A. (2011). Photodegradation of mcresol by

Zinc Oxide under Visible-light Irradiation. International Journal of Chemistry, 3(3), 31-43.

2. Agarry, S. E., and Aremu, M.O. (2012). Batch equilibrium and kinetic studies of

simultaneous adsorption and biodegradation of phenol by pineapple peels immobilized

Pseudomonas aeruginosa NCIB 950. British Biotechnlogy Journal, 2(1), 26-48.

3. Agarry, S.E., Ogunleye, O.O and Aworanti, O.A. (2013). Biosorption equilibrium, kinetic and

thermodynamic modelling of naphthalene removal from aqueous solution onto modified spent

tea leaves. Environmental Technology, 34(7), 825-839

4. Ahmed, S., Rasul, M.G., Martens, W.N., Brown, R., and Hashib, M.A. (2011). Advances in

heterogeneous photocatalytic degradation of phenols and dyes in wastewater: a

review. Water, Air, & Soil Pollution, 215(1-4), 3-29.

5. Aisien, F.A., Amenaghawon, N.A. and Akhidenor, S.A. (2013). Adsorption of Ethylbenzene

from Aqueous Solution using Recycled Rubber from Scrap Tyre. Journal of Scientific

Research and Reports, 2(2), 497-512

6. Aku, S.Y., Yawas, D.S., Madakson, P.B., and Amaren, S.G. (2012).Characterization of

Periwinkle Shell as Asbestos-Free Brake Pad Materials. The Pacific Journal of Science and

Technology, 13(2), 57-63.

7. Alamo-Nole, L.A., Perales-Perez, O., and Roman-Velazquez, F.R. (2011). Sorption study of

toluene and xylene in aqueous solutions by recycled tires crumb rubber. Journal of hazardous

materials, 185(1), 107-111.

8. Amenaghawon, N.A., Aisien, F.A., and Agho, O.E. (2013). Adsorption of Toluene by Waste

Tyre Rubber Granules: Effect of Operating Variables, Kinetic and Isotherm Studies,

International Journal of Scientific Research in Knowledge, 1(10), 427-428.

9. Ania, C.O., Cabal, B., Pevida, C., Arenillas, A., Parra, J.B., Rubiera, F., and Pis, J.J. (2007).Removal

of naphthalene from aqueous solution on chemically modified activated carbons. Water research,

41(2), 333-340.

10. Anirudhan, T.S. and Radhakrishnan, P.G. (2008). Thermodynamics and kinetics of adsorption

of Cu (II) from aqueous solutions onto a new cation exchanger derived from tamarind fruit

shell, Journal of Chemical Thermodynamics 40, 702–709.

11. Annadurai, A., Ling, L.Y. and Lee, J.F. (2007). Biodegradation of phenol by Pseudomonas

pictorum on immobilized with chitin. African Journal of Biotechnology, 6(3), 296-303.


12. Annadurai, G., and Krishnan, M.R.V. (1997). Batch equilibrium adsorption of reactive dye on

to natural biopolymer. Iranian Polymer Journal, 16, 169-172.

13. APHA-AWWA-WPCF (1989). Standard methods for the examination of water and

wastewater. American Public Health Association, New York.

14. ATSDR. (2005). Toxicological Profile for Naphthalene, 1-methylnaphthalene, and 2-

methylnaphthalene; U.S. Department of Health and Human Services, Agency for Toxic

Substances and Disease Registry: Atlanta, GA, USA, 1-291.

15. Bianco-Prevot, A., Baiocchi, C., Brussino, M.C., Pramauro, E., Savarino, P., Augugliaro, V.,

Marci, G. and Palmisano, L. (2001). Photocatalytic degradation of acid blue 80 in aqueous

solutions containing TiO2 suspensions. Environmental science & Technology, 35(5), 971-976.

16. Chang, C.F., Chang, C.Y., Chen, K.H., Tsai, W.T., Shie, J.L. and Chen, Y.H. (2004).

Adsorption of naphthalene on zeolite from aqueous solution. Journal of colloid and Interface

Science, 277(1), 29-34.

17. Gautam, S., Kamble, S.P., Sawant, S.B. and Pangarkar, V.G. (2005). Photocatalytic

degradation of 4-nitroaniline using solar and artificial UV radiation. Chemical Engineering

Journal, 110(1), 129-137.

18. Hallamn, M. (1992). Photodegradation of di-n-butyl-ortho-phthalate in aqueous solution.

Journal of Photochemistry and Photobiology A: Chemistry, 66(2), 215-223.

19. Henner, P., Schiavon, M., Morel, J.L. and Lichtfouse, E. (1997). Polycyclic aromatic

hydrocarbon (PAH) occurrence and remediation methods, Anal. Mag. 25, 56–59.

20. Houas, A., Lachheb, H., Ksibi, M., Elaloui, E., Guillard, C. and Hermann, J.M. (2001).

Photocatalytic degradation pathway of methylene blue in water. Applied Catalysis B:

Environmental, 31(2), 145-157.

21. Hykrdová, L., Jirkovský, J., Mailhot, G. and Bolte, M. (2002). Fe (III) photoinduced and QTiO2

photocatalysed degradation of naphthalene: comparison of kinetics and proposal of

mechanism. Journal of Photochemistry and Photobiology A: Chemistry, 151(1), 181-193.

22. Inamdar, J. and Singh, S.K. (2008). Photocatalytic detoxification method for zero effluent

discharge in dairy industry: Effect of operational parameters. International Journal of

Chemical and Biological Engineering, 1(4), 160-164.

23. Jia, C. and Batterman, S. (2010). A Critical Review of Naphthalene Sources and Exposures

Relevant to Indoor and Outdoor Air. International Journal of Environmental Research and

Public Health, 7, 2903-2939.

24. Kothari, S., Ameta, P. and Ameta, R. (2007). Photocatalytic bleaching of Evans blue over

zinc oxide particulate system. Indian Journal of Chemistry Section A, 46(3), 432-435

25. Kosmulski, M. (2006). pH-dependent surface charging and points of zero charge: III. Update,

Journal of Colloid and Interface Science, 298(2), 730-741

26. Konstantinou, I.K. and Albanis, T.A. (2004). TiO2-assisted photocatalytic degradation of azo

dyes in aqueous solution: kinetic and mechanistic investigations: A review. Applied Catalysis

B: Environmental, 49(1), 1-14.

27. Kosmatka, S.H., Kerkhoff, B. and Panarese, W.C. (2003). Design and Control of Concrete

Mixtures, EB001, 14th edition, Portland Cement Association, Skokie, Illinois, USA.

28. Lachheb, H., Puzenat, E., Houas, A., Ksibi, M., Elaoui, E., Guillard, G. and Hermann, J.M.

(2002). Photocatalytic degradation of various types of dyes (Alizarin S, Crocein Orange G,

Methyl Red, Congo Red, Methylene Blue) in water by UV-irradiated titania, Applied

Catalysis B: Environmental, 39(1), 75-90.

29. Lagergren, S. (1898). Zur theorie der sogenannte, adsorption geloster stoffe, Kungliga

Svenska vetenskaps akademiens. HAndlingar, 24, 1-39.

Lair, A., Ferronato, C., Chovelon, J. and Herrmann, J. (2008). Naphthalene degradation in

water by heterogeneous photocatalysis: An investigation of the influence of inorganic anions.

Journal of Photochemistry and Photobiology A: Chemistry.193, 193–203.

30. Langmuir, I. (1914). The adsorption of gases on plane surfaces of glass, mica and platinum.

Journal of American Chemical Society, 40, 361-368.

31. Lathasree, S., Rao, A., SivaSankar, B., Sadasivam, V. and Rengaraj, K. (2004).

Heterogeneous photocatalytic mineralisation of phenols in aqueous solutions. Journal of

Molecular Catalysis A: Chemical, 223(1-2), 101-105.

32. Legube, B., Guyon, S., Sugimitsu, H., and Dore, M. (1986). Ozonation of Naphthalene in

Aqueous Solution- I: Ozone Consumption and Ozonation Products. Water Research

WATRAG, 20(2).

33. Li, Z., Mulholland, J.A., Romanoff, L.C., Pittman, E.N., Trinidad, D.A., Lewin, M.D. and

Sjödin, A. (2010). Assessment of non-occupational exposure to polycyclic aromatic


hydrocarbons through personal air sampling and urinary biomonitoring. Journal of

Environmental Monitoring, 12(5), 1110-1118.

34. Liu, Z., Jacobson, A.M. and Luthy, R.G. (1995). Biodegradation of naphthalene in aqueous

nonionic surfactant systems. Applied and environmental microbiology, 61(1), 145-151.

35. Mahvi AH, Maleki A, and Eslami A. (2004). Potential of Rice Husk Ash for Phenol Removal

in Aqueous Systems. American Journal of Applied Sciences. 1(4), 321-326.

36. Menkiti, M.C., Nnaji, P.C. and Onukwuli, O.D. (2009). Coag-flocculation kinetics and

functional parameters response of periwinkle shell coagulant (PSC) to pH variation in organic

rich coal effluent medium. Nature and Science, 7(6), 1-18.

37. Nagarajan, N., Gunasekaran, P. and Rajendran, P. (2013). Kinetic Studies of Economically

Viable Sorbents in Aquatic Nickel Solution and their Potential in Electroplating Effluent

Treatment. Advanced Biotech, 13(4), 5-11.

38. Olutoge, F.A., Okeyinka, O.M. and Olaniyan, O.S. (2012). Assessment of the suitability of

periwinkle shell ash (psa) as partial replacement for ordinary portland cement (opc) in

concrete. International Journal of Research and Reviews in Applied Sciences, 10(3), 428-434

39. Owabor, C. N. and Iyaomolere, A. I. (2013). Evaluation of the Influence of Salt Treatment on

the Structure of Pyrolyzed Periwinkle Shell. Journal of Applied Sciences and Environmental

Management, 17(2), 321-327.

40. Pal, D. (2012). Adsorption of polycyclic aromatic hydrocarbons using agricultural wastes:

Effect of lignin content, International Conference on Chemical, Ecology and Environmental

Sciences (ICEES 2012), Bangkok, March 17–18, 2012.

41. Park, D., Yun, Y.S. and Park, J.M. (2005). Studies on hexavalent chromium biosorption by chemically

treated biomass of Ecklonia sp. Chemosphere, 60, 1356-1364

42. Pramauro, E., Prevot, A.B., Vincenti, M. and Gamberini, R. (1998). Photocatalytic

degradation of naphthalene in aqueous TiO2 dispersions: Effect of non-ionic

surfactants. Chemosphere, 36(7), 1523-1542.

43. Qamar, M., Saquib, M., and Muneer, M., (2005). TiO2-mediated photocatalysed degradation

of two selected azo dye derivative chryosidine R and acid red 29 in aqueous suspension.

Desalination, 186, 255-271.

44. Rana, S. and Sharma, T. (2010). Photocatalytic Degradation of 2-Nitroaniline: A Major Water

Pollutant. Dronacharya Research Journal, 2(2), 47-52.

45. Stylidi, M., Kondarides, D.I. and Verykios, X.E. (2003). Pathways of solar light-induced photocatalytic

degradation of azo dyes in aqueous TiO2 suspensions. Applied Catalysis B:

Environmental, 40(4), 271-286.

46. Tsyntsarski, B., Petrova, B., Budinova, T., Petrov, N., Velasco, L. and C.O. Ania, (2011).

Characterization and application of activated carbon from biomass and coal wastes for

naphthalene removal, Bulgarian Chemical Communications 43, 552–557.

47. Umoh, A.A. and Olusola, K.O. (2012). Compressive Strength and Static Modulus of

Elasticity of Periwinkle Shell Ash Blended Cement Concrete. International Journal of

Sustainable Construction Engineering and Technology, 3(2), 45-55.

48. Vasconcelos, T.G., Kümmerer, K., Henriques, D.M. and Martins, A.F. (2009). Ciprofloxacin

in hospital effluent: degradation by ozone and photoprocesses. Journal of hazardous

Materials, 169(1), 1154-1158.

49. Weber W.J. and Morris, J. C. (1963). Kinetics of adsorption on carbon from solution. Journal

of the Sanitary Engineering Division of American Society of Civil Engineering. 89, 31-60.

50. Wilson, N.K., Chuang, J.C., Lyu, C., Menton, R. and Morgan, M.K. (2003). Aggregate

exposures of nine preschool children to persistent organic pollutants at day care and at

home. Journal of Exposure Science and Environmental Epidemiology, 13(3), 187-202.

51. Woo, O.T., Chung, W.K., Wong, K.H., Chow, A. T. and Wong, P.K. (2009). Photocatalytic

oxidation of polycyclic aromatic hydrocarbons: Intermediates identification and toxicity

testing. Journal of Hazardous Materials, 168(2), 1192-1199.

52. Wu, R.J., Chen, C.C., Chen, M.H. and Lu, C.S. (2009). Titanium dioxide-mediated

heterogeneous photocatalytic degradation of terbufos: Parameter study and reaction

pathways. Journal of Hazardous Materials, 162(2), 945-953.

53. Zhou, A., Peng, J., Chen, Z., Du, J., Guo, Z., Ren, N. and Wang, A. (2012). Statistical

Optimization of Operational Parameters for Enhanced Naphthalene Degradation by

TiO2/Fe3O4-SiO2 Photocatalyst. International Journal of Photoenergy. 2012, 1-9.

heterogeneous photocatalytic degradation of … n1 2014 pp 31-45.pdfheterogeneous photocatalytic...

Documents