heat exchanger
TRANSCRIPT
![Page 1: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/1.jpg)
HEAT EXCHANGERHEAT EXCHANGER
Presentation on Presentation on
![Page 2: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/2.jpg)
Heat Exchanger is a device to transfer of heat from one medium to other medium.
Two fluids of different temperatures, one flows through the tubes and other flows out side tubes but inside the shell.
Heat is transferred through the tube walls.
![Page 3: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/3.jpg)
1. Tubular Exchanger a. Shell – and – Tube Exchanger b. U - Tube Exchanger c. Kettle reboiler Type Exchanger d. Double pipe Type Exchanger
2. Extended Surface a. Plate type Exchangers b. Finned Tube
![Page 4: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/4.jpg)
1. Shell2. Front End Head 3. Rear End Head4. Inlet / Outlet Nozzles5. Tube sheets 6. Tubes 7. Baffles8. Tie Rods9. Stiffener Plate10. Impingement plate
![Page 5: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/5.jpg)
![Page 6: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/6.jpg)
U- Tube bundle
U- Tube bundle
Kettle re -boiler Type
Kettle re -boiler Type
![Page 7: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/7.jpg)
Double Pipe Exchanger
Double Pipe Exchanger
Typical Example of Shell and Tube
![Page 8: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/8.jpg)
1. Cross Flow to Tubes
2. Parallel Flow to Tubes
![Page 9: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/9.jpg)
TEMA –Tubular Exchangers Manufacturer's Association
ASME Codes Sec-VIII-Div I and IIASME Sec –II A , B ,C ,D- Materials , Welding
consumables, propertiesASME Sec –IX – Welder qualificationASME Sec –V - NDTANSI standardsNACE standards/ recommended practicesAPI standards 660Process Licensor's guidelines
![Page 10: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/10.jpg)
ShellFront endstationary head type
Rear endhead type
Alphabetical Letters given for the front end, shell and rear end types.
Exchanger designated with three letter .
Example : AES, BES, AKT ... Etc,
![Page 11: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/11.jpg)
![Page 12: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/12.jpg)
![Page 13: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/13.jpg)
They support the tubes during assembly and operation.Help to prevent vibration from flow induced eddies. Two types of baffles : 1. Plate type 2. Rod type
Baffle Cut : Cut in each baffle to permit the shell side fluid to flow across the baffle . Baffle cut can vary between 15% - 45 % of the shell ID
![Page 14: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/14.jpg)
A triangular or rotated triangular pattern will accommodate more tubes than a square or rotated square pattern. A triangular pattern produce a high heat-transfer coefficient.Typical tube pitch of 1.25 times the tube OD.Mechanical cleaning of triangular tubes pattern is very difficult.Square pattern must be used where mechanical cleaning is required.
TUBE PITCH : It is defined as the shortest distance between two adjacent tubes. Minimum tube pitch is 1.25 times of tube OD.
![Page 15: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/15.jpg)
To join tubes and tubesheet and keep the tubes structurally stable and support the skeleton assembly under design conditions.To prevent intermixing of shell and tube sheet fluids.To take care of Longitudinal, Compressive, Mechanical and Thermal axial loads coming on tubes.
Expansion
•Tubes are attached to the tube sheet by Pneumatic or hydraulic pressure or by roller expansion.
![Page 16: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/16.jpg)
Strength weld is one in which the design strength of the weld is greater than or equal to the maximum allowable axial tube strength.
Seal weld is used to supplement an expanded tube joint to ensure tube joint leak tightness.
![Page 17: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/17.jpg)
Where the fluid velocity for the nozzle diameter is high, an impingement plate is specified.To distribute the fluid evenly to the tubes.To prevent fluid enduced erosion, cavitations and vibration
![Page 18: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/18.jpg)
Shell : CS / SS / Non-ferrous typesTubes : CS / AS / SS / Non-ferrousTube Sheet : Forgings / PlatesNozzle Pipes : CS / AS / SSNozzles : CS / AS / SSGaskets : CAF, Spiral Wound, IJA,
Ring Joint typeFasteners : CS / AS / SSName Plate : SS
![Page 19: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/19.jpg)
Material Identification (Pressure parts)FormingWeldingReview of WPS / PQR / Welder QualificationNDTStage and Final InspectionsMock-up AssemblySkeleton AssemblyTube BundleInsertion of Tube Bundle into ShellTesting (Hydro testing / Pneumatic testing)PaintingDocumentationPacking / Protection / Dispatch
![Page 20: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/20.jpg)
Provided to seal the joints against leakSpiral wound with asbestos fill or graphite fillMetal jacketedRing joint typeCamprofile typeCAF – only for less critical servicesMaterial SS 304, SS 316
![Page 21: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/21.jpg)
Identify leak type and location: hydrotestingAttend leak :
gasket leak- re-tighten or replace retubing or plugging leaky tubes re-expansion of tube sheet joint/ re-welding
Cleaning of tube side /shell side as per requirementsInstall new bundles/ shell as per requirementOffer statutory tests as per schedule (IBR Etc.)Timely modifications in shell side/ tube side as per CTS/CES/FDC/Licensor requirements
![Page 22: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/22.jpg)
Civil jobs : foundation / pedestal/ structuresInspection as received condition- check for N2 purging of shell & tube sidesPhysical installation : LevelingSite Checks: ITP format fill upAlignment to upstream downstream tube side / shell side pipingInsulation wherever necessary
![Page 23: Heat Exchanger](https://reader035.vdocuments.site/reader035/viewer/2022081720/55a203591a28ab47268b47e3/html5/thumbnails/23.jpg)