hardware version firmware version minimum 6 74.[29 ... · fiat 500 2012-2016 ... version logicielle...
TRANSCRIPT
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
ALL REV.: 20170605
FLASH LINK UPDATER 2 FLASH LINK UPDATER 2
1XMicrosoft Windows Computer &Internet connection
Ordinateur Microsoft Windows & connection Internet
FLASH LINK UPDATER 2 FLASH LINK UPDATER 2
1XMicrosoft Windows Computer &Internet connection
Ordinateur Microsoft Windows & connection Internet
Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule sup-portées dans ce diagramme (fonctionnelles si équipé)
VEHICLEVEHICULES
YEARS ANNÉES Im
mob
ilize
r byp
ass
Con
tour
nem
ent
d’im
mob
ilisa
teur
Lock
Unl
ock
Tach
omet
er
Trun
k - o
pen
Doo
r Sta
tus
Trun
k S
tatu
s
Hoo
d S
tatu
s *
Han
d-B
rake
Sta
tus
Foot
-Bra
ke S
tatu
s
OEM
Rem
ote
mon
itorin
g
FIAT500 2012-2016 • • • • • • • • • • •500 Turbo 2012-2016 • • • • • • • • • • •500C 2012-2016 • • • • • • • • • • •
Parts required (Not included) Pièce(s) requise(s) (Non incluse(s))
1x Fuse 1x 10 Amp Fusible
HARDWARE VERSIONVERSION MATÉRIELLE
FIRMWARE VERSIONVERSION LOGICIELLE This manual may change without notice.
www.fortinbypass.com for latest version.Ce Guide peut faire l’objet de changement
sans préavis. www.fortinbypass.com pour la récente version.
MINIMUM 6 74.[29]CHRYSLER/DODGE/JEEP/MITSUBISHI MINIMUM
NOTES
* Hood Status Hood Status : functional if equipped with a factory hood switch.
HOOD STATUS : fonctionnel si équipé d’un commutateur de capot d’origine.
OPTION 1
WITH OEM ALARM FUNCTIONAL AND OEM REMOTE FUNCTIONAL :
The vehicle’s OEM alarm can only be disarmed through the OEM remote.
When the vehicle is remote started, if the remote starters remote is used to unlock the doors, the engine will shut off as soon as a door is opened and the vehicle will have to be started normally with the key, the alarm will be disabled.
AVEC ALARME D’ORIGINE FONCTIONNELLE ET TÉLÉCOMMANDE D’ORIGINE FONCTIONNELLE : La désactivation de l’alarme du véhicule par déverrouillage des portes est possible qu’avec la télécommande d’origine.
Au démarrage à distance, si la télécommande du démarreur à distance est utilisée pour déverrouiller les portes, à l’ouverture d’une porte le moteur s’éteint et il faut tourner la clé de contact pour redémarrer le véhicule, l’alarme sera ainsi désactivée.
OPTION 2
WITH OEM ALARM NOT FUNCTIONAL AND OEM REMOTE NOT FUNCTIONAL :
The vehicle’s OEM alarm can only be disarmed through the OEM remote.
Remove the battery from the vehicle OEM remote to cancel the vehicle OEM alarm system’s and protect the vehicle with the integreted alarm system’s of the EVO-ALL.
AVEC ALARME D’ORIGINE NON FONCTIONNELLE ET TÉLÉCOMMANDE D’ORIGINE NON FONCTIONNELLE :
La désactivation de l’alarme du véhicule par déverrouillage des portes est possible qu’avec la télécommande d’origine.
Retirez la batterie de la télécommande d’origine pour annuler le système d’alarme d’origine du véhicule et protéger le véhicule par le système d’alarme intégré du EVO-ALL.
Guide # 63381Page 1 / 8
REGULAR INSTALLATION INSTALLATION RÉGULIÈRE
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
NOTES
Program bypass optionIF OEM FUNCTIONAL:
Programmez l’option du contournementSI TÉLÉCOMMANDE D’ORIGINE
FONCTIONNELLE:
UNIT OPTIONOPTION UNITE DESCRIPTION
A6 OFFNON
OPTION 1 : With OEM remote functional
OPTION 1 : Avec télécom-mande d’origine fonction-nelle
Program bypass option:Programmez l’option du contournement:
UNIT OPTIONOPTION UNITE DESCRIPTION
C1OEM Remote status (Lock/Unlock) monitoringSuivi des status (Verrouillage/Déverrouil-lage) de la télécommande d’origine
OPTION 1
Program bypass optionIF OEM FUNCTIONAL:
Programmez l’option du contournementSI TÉLÉCOMMANDE D’ORIGINE
FONCTIONNELLE:
UNIT OPTIONOPTION UNITE DESCRIPTION
A5 OFFNON
OPTION 1 : With OEM remote functional
OPTION 1 : Avec télécom-mande d’origine fonction-nelle
Page 2 / 8
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
(~)CAN2 LOW
(~)CAN2 HIGH
(~)CAN1 LOW
OBD-II connectorConnecteur OBD-II
(+)12V (+)STARTER
Key cylinder.Cylindre de la clé.
(+)IGNITION2
(+)ACCESORY
(+)IGNITION1
Ignition switch.Commutateur d’ignition.
Dash board, BCM.Tableau de bord, BCM.
(MUX)DOOR LOCKS
(~)CAN1 HIGH
(+)KEY RELEASE
(-)HORN
Page 3 / 8
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
Y����� In A1 P����� In A2
P�����/W���� In A3 G���� Out A4 W���� Out A5
O����� In A6 O�����/B���� In A7
D�.B��� In A8 R��/B��� In A9
L�.B���/B���� A10 B���� Out A11
P��� Out A12 Y�����/B���� In A13 B����/W���� Out A14
P���/B���� Out A15 P�����/Y����� A16
G����/W���� A17 G����/R�� A18
W����/B���� A19 L�.B��� A20
C5 B���� C4 G���/B���� C3 G��� C2 O�����/B���� C1 O�����/G����
D6 W����/R�� D5 W����/B��� D4 W����/G���� D3 Y�����/R�� D2 Y�����/B��� D1 Y�����/G����
A C
D
WIRING CONNECTION | GUIDE DE BRANCHEMENTS
1 22 3
1
410 456789
192021 17 16
1415 13 12
18
11
27 25 24 23 2230 29 28
3134 33 32353839 37 3640414445 43 42
4649 48 47505354 52 5155565960 58 57
26
123
OBD-II connectorFront view
Connecteur OBD-II
Vue de face
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
6
14
1
9
GrayGris
Dk.BlueBleu Foncé
Dk.BlueBleu Foncé
WhiteBlanc
OrangeOrange
Red/Lt.GreenRouge/Vert Pâle
Lt.GreenVert Pâle
Violet/RedMauve/Rouge
Brown/OrangeBrun/Orange
BrownBrun
BrownBrun
3 2 1
(+)ACCE-SORY
(+)IGNITION1
(+)IGNITION2 (+)12V (+)
STARTER(MUX)DOOR LOCKS
(+)KEY RELEASE
OPTIONAL - IDLE MODEOPTIONNELSMODE CONTINUE
(~)CAN2HIGH
(~)CAN1HIGH
(~)CAN1LOW
(~)CAN2LOW
Back view. 4-pin Black connector.
at Ignition switch.
Vue de dos. Connecteur Noir
4-pins, au commutateur
d’ignition.
Back view. 3-pin Black connector.
at Ignition switch.
Vue de dos. Connecteur Noir
3-pins, au commutateur
d’ignition.
Back view. 60-pin Black and Blue connector. at dash board,
BCM.Vue de dos.
Connecteur Noir et Bleu 60-pins, dans le tableau de bord, BCM.
Back view. 2-pin White connector. at key cylinder.
Vue de dos. Connecteur White
2-pins, au cylindre de la
clé.
CU
T
CU
T
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
(-)HORN
Green/WhiteVert/Blanc
CU
T
1
C4D3
A1
D2
A18
A17D1
RS7RS2/D2RS6ARS6/A1RS5 C3 C1 C2
FUSE
FUSI
BLE
D6
D4
RS19 OUT Horn (-)
Horn(-)
Horn(-)
RS19
CAN 1 LOWCAN 1 HIGHCAN 2 LOWCAN 2 HIGH
WITH | AVEC DATA-LINK:ALWAYS REQUIREDTOUJOURS REQUIS
NOT REQUIRED WITH DATALINKNON REQUIS EN DATA-LINK
B
REMOTESTARTER
DÉMARREURÀ DISTANCE
WITH | AVEC DATA-LINK:Direct connectionBranchement directe
HOOD IN RS8 (-)HAND BRAKE IN RS9 (-)TRUNK RELEASE(-) OUT RS11
(+/-) IN RS12 TACHOMETER
FOOT BRAKE(+) IN RS13 GROUND OUT WHILE RUNNING (-) OUT RS14 TRUNK(-) IN RS15DOOR (-) IN RS16UNLOCK(-) OUT RS17LOCK(-) OUT RS18
A15A14A13A12A11A8A5A4A3A2
Ground | Masse (-)RS112V BATTERYRS2 IN (+)
PARKING LIGHTSRS3 OUT (-)PARKING LIGHTSRS4 OUT (+)
ACCESSORYRS5 OUT (+)IGNITIONRS6 IN/OUT (+)IGNITION2RS6a OUT (+)
1
STARTERRS7 OUT (+)
Key release (Vehicle)(+)12VKey release (connector)
(MUX) Door Lock (Connector)(MUX)Door Lock (Vehicle)
(-) Hood Status(-) Hand Brake
(-) Trunk Release(-/+) Tachometer
(+) Foot Brake
(-) Ground While Running
(-) Trunk Status(-) Door Status
(-) Unlock(-) Lock
(+) Ignition
W����/B���
B����
L�.B���W����/B����
P�����/Y�����
L�.B���/B����R��/B��� In
O�����/B���� InO����� In
Page 4 / 8
Release the programming button when the LED is BLUE.
2
1
3
4
5
Relâchez le bouton de programmation quand la DEL est BLEU.
Insert the required remaining connectors.
Insérez les connecteurs requis restants.
LOCK
ACC ON
PUSH
START
IGN
T
ATTENDRE,
ournez la clé à Ignition.urn the key to the
The BLUE LED will turn OFF. La DEL BLEUE s’éteindra.
The BLUE LED will flash. La DEL BLEUE clignotera.
The BLUE LED will turn OFF. The RED LED will turn ON.
La DEL BLEU s’éteindra. La DEL ROUGE s’allumera.
Turn the key to theOFF position.
Tournez la clé à laposition Arrêt (OFF).
T
WAIT,
Ignition ON/RUN position.
LOCK
ACC ON
PUSH
START
OFF
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
x1HOLD
Press and hold
Insert
theprogramming button:
the 4-Pin (Data-Link)connector.
Appuyez maintenirenfoncé
Insérez
etle bouton de
programmation:le connecteur 4 pins
(Data-Link) The Blue, Red, Yellow andBlue & Red LEDs willalternatively illuminate.
Les DELs Bleue, Rouge,Jaune et Bleue & Rouges'allumeront alternativement.
RELEASE
If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
ON BLUE BLEU
Si le DEL n'est pas BLEU débranchez le connecteur 4 pins (Data-Link) et allez au début de l'étape 1.
ON
OFF
IGNITION ON IGNITION OFF
WAIT
OFF
FLASHRAPIDLY
IGNITION OFF IGNITION ON
ON
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DCRYPTOR PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION AVEC DCRYPTEUR
Parts required (not included) Pièces requises (non incluses)
1x FLASH LINK UPDATER 2,
1x FLASH LINK MANAGER software1x Microsoft Windows Computer with Internet connection
1x FLASH LINK UPDATER 2, 1x Programme FLASH LINK MANAGER1x Ordinateur Microsoft Windows avec connection Internet
Page 5 / 8
6
LOCK
ACC ON
PUSH
START
IGN
LOCK
ACC ON
PUSH
START
OFF
The YELLOW LED will turn ON. The RED LED will turn OFF. The RED LED will turn ON.
La DEL JAUNE s’allumera. La DEL ROUGE s’éteindra. La DEL ROUGE s’allumera.
The RED and the YELLOW LED’s alternate.
Les DELs ROUGE et JAUNE alternent.
LOCK
ACC ON
PUSH
START
IGN
Tournez la clé à Ignition.urn the key to theTIgnition ON/RUN position.
Turn the key to the OFF position.Turn the key to the Ignition ON/RUN position,
UNTIL:
Repeat this process approxi-mately 10 times.
Répétez ce processus environ 10 fois.
Tournez la clé à la position Arrêt (OFF).Tournez la clé à Ignition,
JUSQU’À CE QUE:
ON
OFF
ON
x10
IGNITION ON
ON ON
ON
IGNITION OFF
ON
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 2/2 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/2
EVO-ALL
Disconnect all the connectors and after the Data-Link (4-pins) connector.
Débranchez tous les connecteurs et ensuite le connecteur Data-Link (4-pins).
FLASH LINKUPDATER 2
FLASH LINKUPDATER 2
FLASH LINK MANAGERSOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connectionOrdinateur Microsoft Windows avec connection Internet
Parts required (not included)Pièces requises (non incluses)
Connect the module to the FLASH LINK UPDATER 2 and visit the DCryptor menu in the Flash-Link Manager.
Branchez le module au FLASH LINK UPDATER 2et visitez le menu DCryptor dans le Flash-Link Manager.
AFTER DCRYPTOR PROGRAMMING COMPLETEDGo back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
APRÈS LA PROCÉDURE DE PROGRAMMATION DCRYPTOR COMPLETÉE : retournez au véhicule etrebranchez le connecteur 4-pins (Data-Link) et après, tous les connecteurs du EVO-ALL.
EVO-ALL
7
8
9
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARMETest the remote starter. Remote start the vehicle.Testez le démarreur à distance. Démarrez le véhicule à distance.
The module is now programmed.Le module est programmé.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARMETest the remote starter. Remote start the vehicle.Testez le démarreur à distance. Démarrez le véhicule à distance.
The module is now programmed.Le module est programmé.
Page 6 / 8
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
REMOTE STARTER FUNCTIONALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE
Remote start the vehicle with the OEM remote
OR remote starter remote.
Démarrer le véhiculeavec la télécommande d'origine
OU celle du démarreur à distance.
All doors must be closed.
Toutes les portes doivent être fermées
Unlock the doors with the OEM remote.
Déverrouillez les portes avec la télécommande
d'origine.
Remote start the vehicle with the remote starter remote.
Démarrer le véhiculeavec la télécommande du
démarreur à distance.
All doors must be closed.
Toutes les portes doivent être
fermées
Start
Start
UNLOCK
Unlock the doors with the remote starter remote.
Déverrouillez les portes avec la télécommande du
démarreur à distance.
UNLOCK
Unlock the doors with the remote starter remote.
Déverrouillez les portes avec la télécommande du
démarreur à distance.
Start the vehicle
Démarrer le véhicule.
The engine will shut down as soon as a
door is opened.
Lors de l'ouverture d'une porte le
moteur s'éteindra.
OFF
LOCK
START
Turn the Ignition to the ON/RUN position.
Tournez la clé en position ignition (ON).
LOCK
TURNON/RUN
Turn the Ignition to the ON/RUN position.
Tournez la clé en position ignition (ON).
LOCK
TURNON/RUN
OEM REMOTE FUNCTIONAL :TÉLÉCOMMANDE D'ORIGINE FONCTIONNELLE :
La désactivation de l'alarme du véhicule par déverrouillage des portes est possible qu'avec la télécommande d'origine.
Au démarrage à distance, si la télécommande du démarreur à distance est utilisée pour déverrouiller les portes, à l'ouverture d'une porte le moteur s'éteint et il faut tourner la clé de contact pour redémarrer le véhicule, l'alarme sera ainsi désactivée.
AVEC ALARME D’ORIGINE FONCTIONNELLE
ET TÉLÉCOMMANDE D’ORIGINE FONCTIONNELLE :
OPTION 1
OPTION 2REMOTE STARTER (OEM REMOTE NOT FUNCTIONAL) :TÉLÉCOMMANDE DU DÉMARREUR À DISTANCE (TÉLÉCOMMANDE D'ORIGINE NON FONCTIONNELLE) :
UNLOCK
UNLOCKLOCK
LOCK
The vehicle's OEM alarm can only be disarmed through the OEM remote.
When the vehicle is remote started, if the remote starters remote is used to unlock the doors, the engine will shut off as soon as a door is opened and the vehicle will have to be started normally with the key, the alarm will be disabled.
WITH OEM ALARM FUNCTIONAL
AND OEM REMOTE FUNCTIONAL :
OROU The vehicle can now be
put in to gear and driven.
Vous êtes maintenant prêt à embrayer et prendre la
route.
The vehicle can now be put in to gear and driven.
Vous êtes maintenant prêt à embrayer et prendre la
route.
AVEC ALARME D’ORIGINE NON FONCTIONNELLE
ET TÉLÉCOMMANDE D’ORIGINE NON FONCTIONNELLE :
La désactivation de l'alarme du véhicule par déverrouillage des portes est possible qu'avec la télécommande d'origine.
Retirez la batterie de la télécommande d'origine pour annuler le système d'alarme d'origine du véhicule et protéger le véhicule par le système d'alarme intégré du
The vehicle's OEM alarm can only be disarmed through the OEM remote.
Remove the battery from the vehicle's OEM remote to cancel the vehicle OEM alarm system's and protect the vehicle with the integrated alarm system of the
WITH OEM ALARM NOT FUNCTIONAL
AND OEM REMOTE NOT FUNCTIONAL :
EVO-ALL.EVO-ALL.
Page 7 / 8
ALL
Service No : 000 102 04 2536
Date: xx-xx
INTERFACE MODULE
Made in CanadaPATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
HARDWARE VERSION FIRMWARE VERSION
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation GuidesUpdated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installationsDes mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNINGThe information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les fi ls et circuits avant d’effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2014, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORTTél: 514-255-HELP (4357) 1-877-336-7797
ADDENDUM GUIDEWEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com
EVO-ALL
Page 8 / 8