handle k-17890-rlresources.kohler.com/plumbing/kohlerapac/pdf/17890-rl.pdf · 2018-12-18 ·...
TRANSCRIPT
1242827-T01-B
WADING POOL BATHROOM SINK
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS/
®
K-17890-RLDERRING
TM
� ( )
( )
�
�
�
�
�
�
�
�
�
�
�
�
13mm
TOOLS AND MATERIALS(Not Supplied)�
�
�
�
�
�
�
�
�
�
�
�
�
Template(supplied)
Safety glasses
Pencil
Scissors
Tape measure
Putty knife
Plumbers putty
Hacksaw
Keyhole saw or saber saw
Drill (13mm or 1/2 dia. drill bit or larger)
Adjustable wrench
Pipe wrench
Tubing cutter
BEFORE YOU BEGIN�
�
�
�
�
�
�
�
Observe all local plumbing and buildingcodes.
Inspect the waste and supply tubing;replace if necessary.
Prior to installation, unpack the newlavatory and carefully inspect it fordamage. Return the lavatory to itsprotective carton until you are ready toinstall it.
For replacement installations, make surethe existing cutout is the same or smallersize as the new lavatory.
Use the template supplied with thelavatory to mark correct size cutout.
Kohler lavatory is made according toAmerican National Standard that it canmatch the American lavatory fittings . Anyother lavatory fittings may not fit for kohlerlavatory.
Fixture dimensions are nominal andconform to tolerances established byASME Standards (A112.19.2-2013).The product complies with GB 6952-2015.
�
�
�
�
�
�
�
�
ASME (A112.19.2-2013)
GB 6952-2015
FOR SELF-RIMMING INSTALLATIONCUT ALONG THIS LINE
400 mm
RIM OF LAVATORY
ROUGHING-IN
Kohler reserves the right to change marked dimensions without prior notice.
Unit: mm:
Reference Value
1-1/4" OD
3/8" Hot 3/8" Cold
102
Recommended ADA Installation
686Min
203Min
279
229Min
864
61051
449
19
152295
356
0 Co
IMPORTANT CONSUMER
INFORMATION (
Do not use the product in the water below 0 C.o
CARE AND
CLEANING)
To keep your lavatory looking new, make sure you rinse it out
thoroughly after each use. on this
product, as they will scratch and ruin the surface. Stubborn
stains, paint, or tar can be removed with turpentine or paint
thinner.
Please do not use hard materials (like
scouring pad) to clean product surface, especially the
product logo.
DO NOT USE ABRASIVES
CAUTION:
For Artist Edition Products:
Treat your decorative product just as you would treat your fine
china. The best way to clean it is to use warm water and pat dry
with a cotton cloth or soft sponge. use bristle brushes
or abrasive-backed sponges. They will scratch the decorative
surface.
DO NOT
�
�
1.
2. 5"(127mm)
3.
4.
5.
6.
7.
8.
9.
10.
11.
INSTALL THE LAVATORY
�
�
Choose between a wall-mount or countertop
faucet. Either choice will work, although a
wall-mount faucet is recommended.
The sink shown may differ from your
actual product. The installation steps still apply.
Do not install the
faucet trim until instructed.
NOTE:
Wall-Mount Faucets:
1. Position the
template on the countertop.
Countertop Installations:
2. Faucet spout must be at
least 5"(127 mm) in length.
Use the spout centerline
on the template to ensure faucet clearance.
Wall-Mount Faucet:
Countertop Faucet:
3. Mark the faucet spout,handle, and sink cutout locations on thecountertop.
Re-check the clearance between the lavatory,faucet, backsplash, and cabinet. Adjust thetemplate accordingly.
Countertop Faucet:
4. Drill a pilot hole and cut the countertop opening
along the traced line.
5. Drill the faucet holes.
Install the faucet according to instructions.
Countertop Faucets:
6. Install the drain.
7. Apply a thin, continuous bead of sealant
around the sink opening.
8. Position the sink in the opening. Wipe away
excess sealant. Allow the sealant to cure.
9. Install the faucet trim by
following the instructions.
Wall-Mount Faucets:
10. Complete the water supply and drain
connections.
11. Run water into the sink and check all
connections for leaks.
127Min
Spout Centerline
Spout
Handle
Handle
©
©
Copyright Kohler China Investment Co., Ltd. 2017
2017
KOHLER CHINA INVESTMENT CO., LTD NO.158, JIANG CHANG SAN ROAD,JING'AN DISTRICT, SHANGHAI, PRC POST CODE: 200436
( ) 158 200436