Applicable model: XG-0301

Handheld Garment Steamer

Operation Manual

Please carefully read this manual before using the product.

Dear customer, Thank you for choosing our handheld garment steamer. This product is simple for operation, light , portable and has strong functions. It helps to remove wrinkles and dusts on garment and may bring you to an new garments care experience in future travel.

Important Safety Instructions

When using your appliance, basic precautions should always be followed, including the following: 1. Please carefully read this manual before use. 2. Please use this machine as per the purpose specifi ed in this manual and do not use it for other purpose. 3. To avoid electric shock and other hazards, don't immerse this machine, power cord and the plug into water. 4. Never yank cord to disconnect from outlet. Please hold the plug and pull it out of the socket gently. Your hand must be dry. 5. Don't fi ll the machine with hot water or add any corrosive cleanser in water; otherwise, the machine may be damaged. It is recommended to use minerals free water . 6. Always disconnect from electrical outlet when the garment steamer is not in use, or when adding water into the water tank or when there is no water in the water tank. 7. When the power supply or the machine is damaged, don't run this product. To avoid electric shock, don't try to dismantle or repair this machine. Send it to a qualifi ed repair center for inspection and repair. Private dismantling, repair or replacement may lead to hazards of a fi re, electric shock or personal injury in machine use process.

1

8. Don't let the product running in an unattended area. Immediate turn off the power while if child is attempts to use or approach this product. Close supervision is necessary for any appliance being used by or near children. 9. Exposure to the panel at the steam outlet or the exposure to steam may lead to scalding. Pay attention to safety when put the garment steamer upside down. 10. Beware high temperature steam while using this product. To minimize hazards of exposure to hot steam, please don't point the steamer to any person or pet when using this product. 11. The product must be use under supervision or guidance of well knowledge personal, and straightly forbidden as toy for children. 12. Do not allow cord to touch hot surfaces. Let appliance cool completely before putting away. Loop cord loosely around appliance when storing. 13. DO NOT use this product if the power cord is damaged, consult with manufacturer or the service provider, or local sales dealer. 14. Please consult to local government for recycling by law, DO NOT dump this product into general waste! 15. To reduce the risk of contact with hot water emitting from steam vents, check appliance before each use by holding it away from body and operating steam button.

Save These Instructions

To reduce the likelihood of circuit overload, do not operate another high wattage appliance on the same circuit. If an extension cord is absolutely necessary, a (ampere rating of the appliance) ampere rated cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over.

2

Product schematic diagram

1. Trouser clamp

2. Fine hair brush

3. Long hair brush

4 1

4.Steam jet

5. Switch

6. Indicator

5

7

6

2

7. Main machine

8.Water tank 3 8

Specifications

Rated voltage: 110-120V~ Rated frequency: 60Hz

Rated power: 860W Water tank capacity: 320ml

3

Water filling

1 2 3 4

Disconnect power supply Counterclockwise turning Take out the water tank Remove the silicon plug

5 6 7 8

Fill up water in 80% full level Insert the silicon plug Direct the trigangle at

the line Closewise turning for locking

Note:

Normal tap water may be used for this product. However, if water hardness at your

area is too high, limescale may quickly be generated. Therefore, it is recommended

to add distilled water in the tank to extend service life of the product. Don't add any

corrosive liquid or cleanser in water to avoid product damage.

4

Start-up

Note:

To extend product service life, water lacking shall be avoided! When the steam is insufficient,

please pull off the power supply and add water.

1 2 3

24S

Install the water tank, Connect to power supply. Press the switch; the indicator

will be on in red and then change to blue after 24s of preheating. Steam will be supplied automatically.

counterclockwise turn the steam jet by 180 degrees.

4 5

Press the switch again;

indicator off; no more steam out.

Pull out the plug; work stops.

5

Steaming operation

1. Before using the garment steamer, add water in the water tank by the method specified above.

2. Counterclockwise turn the steam jet by 180 degrees (see Fig. 1); connect to power supply and

press the switch to start steaming.

3. During steaming, don't touch the steam jet. Keep it at least 20cm away from your body to avoid scalding.

4. Don't direct steam at anybody.

5. Before steaming, pull the garment straight to facilitate steaming. Garment with fewer wrinkles is

relatively easy for steaming while more wrinkles require repeated steaming.

6. This product is not suitable for plat or inverted steaming (see Fig. 2 and Fig. 4); move the steam

jet up and down (see Fig. 5 and Fig. 7) to facilitate wrinkle removing.

7. When moving the steam jet, pull flat the garment for steaming gently to achieve better steaming effect.

1 2 3 4

5 6 7

6

Trouser clamp and brush installation

Note: be sure to disconnect the power before trouser clamp and brush is attached or

dismantling. Pay attention that the steam jet may still be very hot and you should wait it for cooling done before attach or remove any accessory. For accessory installing, pay attention to the direction to avoid blocking steam ejecting holes. The arrow on the accessory must be direct at the triangle on the steam jet. Maintain consistent direction.

Trouser clamp The trouser clamp helps for steam penetration into thick fiber for quicker styling.

Fine hair brush The fine hair brush may remove static and fiber and hair on the garment.

Direct card positions on

both sides and press down.

Installation completed. Direct card positions on

Installation completed. both sides and press down.

Long hair brush The long hair brush may remove dust and dirt.

Don't apply the brush for gentle fabric, such as

silk or satin.

Fine hair brush Long hair brush

Direct card positions on

both sides and press down.

Installation completed.

7

Cleaning and maintenance

Note: don't clean this product with steel wool, abrasive cleanser or corrosive liquid

(such as alcohol, gasoline or acetone. It shall be cleaned by wet cloth and non-corrosive

liquid; wipe away sediments in the steam jet.

Remove residual water in the tank completely. Wait for cooling of the machine before

put it inside the package.

1 2 3

1.5 hours

Disconnect power supply. Wait for cooling before cleaning(Wait for 1.5 hours for cooling) Remove sediments in

the steam jet.

4 5

Remove water completely. Pack in the carton.

8

Fault analysis

Common faults Causes Solution

No power connection Insert the plug into the socket

Press the steam switch completely Fail to press the steam switch fully

Water level in the tank is too low

The water tank is not properly placed

Pull of the plug and add water in the tank

Install the tank correctly

No steam going out

of the garment steamer

The machine is inversed thus leading

to the failure of water suction Use the machine correctly

If it is not the above reason, it may

be the fault of the machine Send to the repair department for repair

Water ejecting when

starts up the machine

This phenomenon will disappear after 24s of

preheating Inadequate preheating time

Water ejecting in

the midway

Water out in little amount under

pressure This is the normal phenomenon

Water pumping sound/

handle vibration of the

garment steamer

Vibration generated by the electric

pump This is the normal phenomenon

9

Product Warranty Card

Purchasing date

Name/ unit

Telephone

Address

(MM/DD/YY)

Fax

Machine No.

City

Model

E-mail

Repair records

- If you need services or information, please contact related distributors.

- Warrant services will be provided only in the effective warranty term under normal using

situation. In case of any fault due to the problem of the product rather than any artificial

reason, warranty services may be enjoyed. The following situations are not in the warranty

scope:

1. Damage caused by disassembly by any one not undertaking the warranty services.

2. Damage of the machine due to artificial reason.

3. Damage caused by the failure to correctly use, maintain and repair the machine as per the

operation manual.

4. Damage caused by falling down, squeezing, water immersing and other personal mistake.

5. Damage caused by flood, fire, lightning and other force majeure event.

6. Damage accidentally caused by the purchaser.

7. Please properly keep this warranty card which shall be provided in order to enjoy warranty

services. The warranty card shall not be altered; otherwise, it will be invalid.