hair interceptors - zurn

HAIR INTERCEPTORS

ZURN PLUMBING PRODUCTS GROUP SPECIFICATION DRAINAGE OPERATION, 1801 PITTSBURGH AVENUE, ERIE, PA 16502 PHONE 814/455-0921 FAX: 814/454-7929 WEBSITE: www.zurn.com

Page 45

GENERAL INFORMATION

Zurn has solids interceptors which are specifically designed for hair (Z1175 and Z1176).

Z1175 and Z1176 HAIR INTERCEPTORThese interceptors prevent clogging of waste lines in barber shops,beauty salons, surgery preparation rooms, animal hospitals, orwherever hair may be a problem in the waste lines. The interceptingchamber contains a perforated stainless steel straining elementdesigned to provide maximum interception. The cast iron, counter-sunk, flanged cleanout cover is gasketed to provide a watertight,gastight seal, yet may be easily removed for periodic cleaning of the straining element.

TYPICAL INSTALLATIONS

All solids interceptor options and variations are specified as a PREFIX and/or SUFFIX letter or number added to the series designation.Below are the available options.

PREFIXESZ Standard Assembly (See Engineering Specification)ZAB All Satin Finish

SUFFIXES–CP Chrome Plated Finish–YR Replacement Stainless Steel Basket

OPTIONS and VARIATIONS

PICTORIAL INDEX – HAIR INTERCEPTORS

Z1175Hair Interceptor

Z1176Hair Interceptor

HAIR INTERCEPTORS


Page 46

Z1175 HAIR INTERCEPTOR – OPERATION and MAINTENANCE INSTRUCTIONS

SIZINGThere are no sizing requirements for this interceptor. All units are madewith a 1-1/2" [38 mm] standard pipe size inlet and outlet and arecapable of handling drainage volumes standard to 1-1/2" pipe size.

DESIGNThe Zurn Z1175 Hair Interceptor is designed to retain the hair frombeauty shops, hospitals, or wherever hair clogging of the water systemis a problem. The removable perforated stainless steel basket retainsthe accumulating hair before it can pass through to the sanitarysewer system.

OPERATIONThe wastewater flows from the inlet piping into the perforated basket,passing through the perforations in the basket, into the main bodychamber, then exits the main body chamber into the sanitary drainsystem.

MAINTENANCECleaning should be done on a regular basis, either before or after thebasket becomes clogged. Unscrew and remove the cast iron, counter-sunk, flanged cleanout cover, gasket, and perforated basket. Removethe accumulated hair and reinstall the basket, gasket, and cleanoutcover in the body and tighten cover. Efficiency of operation is directlyrelated to the level of maintenance.

Z1176 HAIR INTERCEPTOR – OPERATION and MAINTENANCE INSTRUCTIONS

SIZINGThere are no sizing requirements for this interceptor. All units are madewith a 1-1/2" [38 mm] standard pipe size inlet and outlet and arecapable of handling drainage volumes standard to 1-1/2" pipe size.

DESIGNThe Zurn Z1176 Hair Interceptor is designed to retain the hair frombeauty shops, hospitals, or wherever hair clogging of the water systemis a problem. The removable perforated stainless steel basket retainsthe accumulating hair before it can pass through to the sanitarysewer system.

OPERATIONThe wastewater flows from the inlet piping into the perforated basket,passing through the perforations in the basket, into the main bodychamber, then exits the main body chamber into the sanitary drainsystem.

MAINTENANCECleaning should be done on a regular basis, either before or after thebasket becomes clogged. Unscrew and remove the cast iron, counter-sunk, flanged cleanout cover, gasket, and perforated basket. Removethe accumulated hair and reinstall the basket, gasket, and cleanoutcover in the body and tighten cover. Efficiency of operation is directlyrelated to the level of maintenance.


Page 63

GREASE, HAIR, SOLIDS, and LINT INTERCEPTORS

CHEMICAL RESISTANCE CHART Typical Powder Coatings

Key: E – No attack G – Appreciably no attackF – Some attack, but unseeable in some instances P – Attacked, not recommended for useN – Rapidly attacked C – Cold, 70°F (21.1°C)H – Hot, 180°F (82.2°C) or boiling point of solvent * – And nitrate and sulfate

Epoxy

Chemical C H

Acids:Acetic, 10% F NAcetic, Glacial N NBenzene Sulfonic, 10% E EBenzoic E EBoric E EButyric, 100% P NChloracetic, 10% E EChromic, 5% F NCitric, 10% E NFatty Acids E EFluosilicic N NFormic, 90% E FHydrobromic, 20% G GHydrochloric, 20% E GHydrocyanic E EHydrofluoric, 20% G GHypochlorous, 5% F NLactic, 5% F N

Epoxy

Chemical C H

Acids (Continued):Maleic, 25% E ENitric, 5% E GNitric, 30% G POleic E EOxalic E EPhosphoric G FPicric G FStearic E ESulfuric, 50% G FSulfuric, 80% F NTannic E E

Alkalies:Ammonium Hydroxide E GCalcium Hydroxide E EPotassium Hydroxide E ESodium Hydroxide E E

Epoxy

Chemical C H

Acid Salts:Aluminum Sulfate E EAmmonium Chloride* E ECopper Chloride* E EIron Chloride* E ENickel Chloride* E EZinc Chloride* E E

Alkaline Salts:Barium Sulfide E ESodium Bicarbonate E ESodium Sulfide E ETrisodium Phosphate E E

Neutral Salts:Calcium Chloride* E EMagnesium Chloride* E EPotassium Chloride* E ESodium Chloride* E E

Epoxy

Chemical C H

Solvents:Alcohols E EAliphatic Hydrocarbons E EAromatic Hydrocarbons E EChlorinated Hydrocarbons F FKetones F FEthers F FEsters F FGasoline E ECarbon Tetrachloride E E

Organics:Aniline G PBenzenc E EFormaldehyde, 37% E GPhenol, 5% G FMineral Oils E EVegetable Oils E EChlorobenzene G P

Z1180 and Z1184 CHEMICAL RESISTANCE CHART For Composite Material in Light Acid Concentration Environment Only

Key: E – Excellent Corrosion Resistance G – Good F – Fair P – Poor

General Outdoor EMarine Outdoor EGeneral Industrial EWater – Pure EWater – Sea E

Acids:Acetic EBoric EChromic ECitric EFatty EFormic EHydrochloric GHydrofluoric F-PNitric FPhosphoric GPicric GSulfuric G

Bases:Ammonium Hydroxide EPotassium or Sodium Hydroxide F-G

Salts:Aluminum Sulfate EAmmonium

Chloride ENitrate EPhosphate ESulfate E

Borax E

Salts (Continued):Copper Sulfate EFerricChloride ESulfate E

MagnesiumChloride ESulfate EMercuric Chloride E

NickelChloride ESulfate E

PotassiumChloride ESulfate E

SodiumBicarbonate EBisulfate EChloride EHypochlorite ENitrate EPhosphate ESilicate ESulfate EThiosulfate E

ZincChloride ESulfate E

Calcium Chloride ESodium Carbonate E

Gases (Wet):Ammonia ECarbon Dioxide EChlorine EHydrogen Sulfide ENitrogen Dioxide G-ESulfur Dioxide ECarbon Disulfide E

Solvents:Acetone EBenzene ECarbon Tetrachloride EEthyl Acetate EEthyl Alcohol EEthyl Ether EEthylene Dichloride EEthylene Glycol EFreon EMethyl Alcohol EMethyl Ethyl Ketone EMethylene Chloride EPerchloroethylene ETrichloroethylene EToluene EXylene E

Oils, Fuels, and Other:ASTM No. 1 Oil EASTM No. 3 Oil EDetergents EGasoline EGrease EJet Fuel EHydraulic Fluid (Ester) EKerosene EMotor Oil E

Medium Rating Medium Rating Medium Rating Medium Rating



Page 64

CHEMICAL RESISTANCE CHART Typical Corrosion Resistance of Stainless Steel to Various Media

CODE: a – Unaffected. b – Slightly attacked. c – Attacked. m – Complete details concerning the conditions of service must be evaluated.

Salts:Aluminum chloride . . . . . . . . . . . . c cAluminum fluoride . . . . . . . . . . . . c bAluminum sulfate . . . . . . . . . . . . . a aAmmonium alum . . . . . . . . . . . . . a aAmmonium bromide . . . . . . . . . . . c aAmmonium chloride . . . . . . . . . . . b aAmmonium hydroxide . . . . . . . . . a aAmmonium nitrate . . . . . . . . . . . . a aAmmonium sulfate . . . . . . . . . . . . a aBarium chloride . . . . . . . . . . . . . . a aBleaching powder . . . . . . . . . . . . c aCalcium chloride . . . . . . . . . . . . . c aCalcium hydroxide or oxide . . . . . . a aCopper chloride . . . . . . . . . . . . . . c cCopper cyanide . . . . . . . . . . . . . . a aCopper nitrate . . . . . . . . . . . . . . . a aCopper sulfate (plus 2% sulfuric acid) . . . . . . . . . . . . . . . a a

Copper sulfate . . . . . . . . . . . . . . . a aCreosote . . . . . . . . . . . . . . . . . . . c aCreosote (plus 3% salt) . . . . . . . . c cHydrogen peroxide . . . . . . . . . . . . b aMagnesium carbonate . . . . . . . . . a aMagnesium chloride . . . . . . . . . . . m mMagnesium sulfate . . . . . . . . . . . . a aMagnesium hydroxide . . . . . . . . . a aMagnesium nitrate . . . . . . . . . . . . a aPhosphorous trichloride . . . . . . . . a aPotassium bromide . . . . . . . . . . . a aPotassium carbonate . . . . . . . . . . a aPotassium chloride . . . . . . . . . . . . m mPotassium chlorate . . . . . . . . . . . . a aPotassium cyanide . . . . . . . . . . . . a aPotassium dichromate . . . . . . . . . a aPotassium ferricyanide . . . . . . . . . a aPotassium ferricyanide (boiling) . . . a aPotassium hypochlorite . . . . . . . . c mPotassium iodide . . . . . . . . . . . . . a aPotassium iodide . . . . . . . . . . . . . a a (sat. plus 0.1% sodium carbonateevaporated to dryness)Potassium hydrate . . . . . . . . . . . . a aPotassium nitrate . . . . . . . . . . . . . a aPotassium oxalate . . . . . . . . . . . . a aPotassium permanganate . . . . . . . a aPotassium sulfate . . . . . . . . . . . . . a aSilver nitrate . . . . . . . . . . . . . . . . a a

Salts (Continued):Silver cyanide . . . . . . . . . . . . . . . a aSodium bicarbonate . . . . . . . . . . . a aSodium borate . . . . . . . . . . . . . . . a aSodium bromide . . . . . . . . . . . . . a aSodium chloride (2% aerated) . . . a aSodium citrate . . . . . . . . . . . . . . . a aSodium fluoride . . . . . . . . . . . . . . b –Sodium hydroxide . . . . . . . . . . . . a aSodium nitrate . . . . . . . . . . . . . . . a aSodium peroxide (212°F) . . . . . . . a aStannic chloride . . . . . . . . . . . . . . c cStannous chloride . . . . . . . . . . . . b –Sulfur (molten) 500°F . . . . . . . . . . a aSulfur chloride . . . . . . . . . . . . . . . b –Titanium tetrachloride . . . . . . . . . a aZinc chloride . . . . . . . . . . . . . . . . c bZinc sulfate . . . . . . . . . . . . . . . . . a a

Miscellaneous:Ammonia . . . . . . . . . . . . . . . . . . . a aBaking oven gases . . . . . . . . . . . . a aBromine . . . . . . . . . . . . . . . . . . . c cCarbonated beverages . . . . . . . . . a aChlorine (wet and dry) . . . . . . . . . c cGlycerin . . . . . . . . . . . . . . . . . . . . a aHydrogen sulfide (400°F) . . . . . . . b aIodine . . . . . . . . . . . . . . . . . . . . . c aLead (molten) . . . . . . . . . . . . . . . c cLysol . . . . . . . . . . . . . . . . . . . . . . m mMercury . . . . . . . . . . . . . . . . . . . a aSauerkraut brine . . . . . . . . . . . . . c aSea water . . . . . . . . . . . . . . . . . . m mSulfur dioxide . . . . . . . . . . . . . . . b bVegetable juices . . . . . . . . . . . . . . a aX-ray developing solution . . . . . . . b aZinc (molten) . . . . . . . . . . . . . . . . c c

TYPE NUMBERSCF8 CF8M

MEDIUM 304 316

Organic Substances:Acetone . . . . . . . . . . . . . . . . . . . . a aBenzol . . . . . . . . . . . . . . . . . . . . . a aCarbon tetrachloride . . . . . . . . . . . c cEthyl alcohol . . . . . . . . . . . . . . . . a aEthyl chloride . . . . . . . . . . . . . . . . a aEthyl ether . . . . . . . . . . . . . . . . . . a aFood pastes . . . . . . . . . . . . . . . . . a aFruit juices . . . . . . . . . . . . . . . . . a aInk . . . . . . . . . . . . . . . . . . . . . . . m mMustard . . . . . . . . . . . . . . . . . . . . b aParegoric cmpd . . . . . . . . . . . . . . a aQuinine bisulfate . . . . . . . . . . . . . b aQuinine sulfate . . . . . . . . . . . . . . . a aVinegar at 70°F . . . . . . . . . . . . . . m m

Acids:Acetic . . . . . . . . . . . . . . . . . . . . . m mBenzoic . . . . . . . . . . . . . . . . . . . . a aBoric . . . . . . . . . . . . . . . . . . . . . . a aCarbolic . . . . . . . . . . . . . . . . . . . . a aChromic (50%) . . . . . . . . . . . . . . . c cCitric . . . . . . . . . . . . . . . . . . . . . . a aFormic . . . . . . . . . . . . . . . . . . . . . c mHydrobromic . . . . . . . . . . . . . . . . c cHydrocyanic . . . . . . . . . . . . . . . . . a aHydrochloric . . . . . . . . . . . . . . . . c cHydrofluoric . . . . . . . . . . . . . . . . . c cLactic . . . . . . . . . . . . . . . . . . . . . a aNitric (conc.) . . . . . . . . . . . . . . . . a aNitric (conc. plus 2% HCI) . . . . . . . a –Nitrous (conc.) . . . . . . . . . . . . . . . a aOxalic . . . . . . . . . . . . . . . . . . . . . m mPhosphoric . . . . . . . . . . . . . . . . . a aPhosphoric (10%) . . . . . . . . . . . . . a aPicric (conc.) . . . . . . . . . . . . . . . . a aPyrogallic (conc.) . . . . . . . . . . . . . a aPyroligneus (conc.) . . . . . . . . . . . . a aStearic (conc.) . . . . . . . . . . . . . . . a aSuccinic (molten) . . . . . . . . . . . . . c –Sulfuric (conc.) . . . . . . . . . . . . . . . a aSulfuric (dil.) . . . . . . . . . . . . . . . . m mSulfuric 15% (plus 2%

potassium dichromate) . . . . . . . . a aSulfurous (conc.) . . . . . . . . . . . . . b aTannic (conc.) . . . . . . . . . . . . . . . a aTartaric (conc.) . . . . . . . . . . . . . . . a aTrichloracetic acid (10%) . . . . . . . a aUric (conc.) . . . . . . . . . . . . . . . . . a a


MEDIUM 304 316


MEDIUM 304 316


Page 65


MATERIALS and FINISHES

Zurn Cast Iron conforms to ASTM Specification for Gray Iron CastingsA 48-83, Class 25. It is produced utilizing the latest equipment andnewest developed foundry techniques. Zurn cast iron castings arecharacterized by a high degree of strength, corrosion-resistance,workmanship, and finish.

Zurn Duresist is a ductile iron complying with ASTM Specification A 536-84, Grade 60-45-10. Its physical properties make it ideal forgrates and drain components that are subjected to severe and heavyduty service. Its chemical characteristics make possible a degree ofcorrosion-resistance far superior to that of cast iron. Zurn Duresistexhibits remarkable stress qualities, possessing a yield strength inthe same range as that of cast carbon steel, while its ability to absorbthe shock loading of traffic areas is unequalled, making its use idealfor all areas where extra heavy duty service is a requirement – whetherindoors or outdoors – in chemical and metal processing plants orother industrial applications.

“Zurn Dura Coat” is a specially formulated paint designed to resistcracking and chipping. Dura Coat is a latex based coating developedto be used with cast iron substrate.

Zurn Galvanized Cast Iron is a process of applying heavy zinc coatingto a thoroughly cleaned iron casting. This coating contains 95% zinc.Zurn galvanizing can be supplied on all cast iron parts. It increaseslongevity and is recommended wherever the discoloration caused by oxidation of cast iron is objectionable. Galvanize should be usedin coastal and industrial areas where corrosive atmosphere may be encountered. Zurn galvanizing meets and exceeds FederalSpecification MIL-P-21035, MIL-P-26915A, MIL-P-26433, and MIL-C-10578 (Type II). It also meets ASTM A239-89 and is listed by Underwriters Laboratories, Inc. (U.L.)

Cadmium Plated Cast Iron is a process of applying a heavy cadmiumcoating to a thoroughly cleaned iron casting. This coating contains95% cadmium in a cold applied process. Cadmium plating can besupplied on all cast iron parts. It increases longevity and is recom-mended wherever the discoloration caused by oxidation of cast ironis objectionable.

Zurn Bronze is a semi-red brass conforming to ASTM Specificationfor Copper Alloy Sand Casting B 584-90, Copper Alloy No. 844. Theexposed surface is normally supplied possessing a satin sheen texturewhich allows it to blend unobtrusively with surrounding finishes. Whenthe application requires, Zurn Bronze can be polished to a high gloss.

Zurn Nickel Bronze is a unique material that is ideally suited totraffic-bearing grates and strainers in finished floor areas. It affordsthe combined advantage of greater strength, better appearance, andlonger service life at the same price as chrome plated brass. Superiorductility and shock resistance are the result of a copper nickel alloy(Copper Alloy 997) having a wearing surface similar in appearanceto satin chrome plate; however, because it does not have a platedsurface it cannot chip, peel, crack, or wear off. It is highly resistantto corrosion; however, the process of oxidation will naturally occurover time with most metals. Methods have been developed to prevent,preserve, and restore metals affected by oxidation.

Chrome Plated Bronze is ideal for installation in walls, gutters,and other areas where a bright decorative finish is desired, and isnot subject to the abrasive action of foot and other traffic. It is notrecommended for installations where the abrasion will eventuallywear through and cause peeling. It should always be specified forswimming pool fittings due to its high resistance to the halogens(chlorine, etc.), encountered in swimming pool sanitation.

Aluminum supplied is casting grade 319. This is an alloy containingboth silicon and copper. It is a solid cast metal in a pleasing lightgray color. The light weight, coupled with its exceptional strengthand corrosion resistance, makes it ideal for drain components suchas sediment buckets and strainers. When used with acid-resistingporcelain enamel coated drains, the possibility of chipping is minimized.

Zurn Stainless Steel castings are normally produced in Type CF8 (304)which is an 18-8 Austenitic Stainless possessing excellent corrosionresistant qualities. For some applications where conditions demand,Type CF8M (316) stainless steel can be supplied. Items formed fromstainless steel sheet and other stainless steel products are regularlyfurnished in Type 304 with 316 as an optional material.

A.R.C. Acid Resisting Epoxy Coating is a baked-on powder coating,which produces a smooth, hard, high gloss finish. This epoxy basedcoating offers high impact resistance and excellent life expectancyin all drainage applications. Zurn A.R.C. coating conforms to therequirements of F.D.A. (Food and Drug Administration) Regulation21-CFR5 117.1360.

A.R.E. Acid Resisting Porcelain Enamel is a substantially vitreous or glassy inorganic coating bonded to metal by fusion at a hightemperature above 800°F. This coating offers excellent acid, abrasion,and wear resistance. The coating is extremely hard and is the ultimatefor sanitation in drainage applications. Zurn A.R.E. coating conforms tothe requirements of F.D.A. (Food and Drug Administration) Regulation21-CFR5 117.1360.

Metal Cast Iron Ductile Iron

Specification Class 25 60-45-10

Tensile Strength (PSI) 25/30,000 60/80,000

Yield Strength (PSI) NIL 45/60,000

Elongation NIL 10% to 25%

Modules of Elasticity 16 x 10 24 x 10

Properties of Basic Ductile Versus Cast Iron

hair interceptors - zurn

Documents