group f”) detailed tender notice no. dte/pur/14/328 ... · connecting rod set of different sizes...
TRANSCRIPT
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
1
Revised specifications of the machinery equipments of Automobile Engineering Departments of New established Polytechnics of the State 2014-15
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
1. FOUR STROKE PETROL CARBURETOR ENGINE SETUP FOR PRACTICE
4-stroke, 4-cylinder water-cooled in line with 2 valves per cylinder engine with battery, Starter motor) radiator, cooling fan oil filter with working condition mounted on M .S frame. Piston displacement 1000 to 1500cc,Bhp 100to120 at 4000-6000rpm
01 01 01
2. FOUR STROKE PETROL MPFI ENGINE SETUP FOR PRACTICE
4-stroke, 4-cylinder water-cooled in line with 2 valves per cylinder M. P. F. I engine with battery, Starter motor, radiator, cooling fan oil filter with working condition mounted on MS frame. Complete With various sensors.
01 01 01
3. FOUR STROKE DIESEL ENGINE SETUP
4-stroke, 4-cylinder water-cooled in line with 2 valves per cylinder engine with battery. Starter motor, radiator, cooling fan, oil filter and F.l .P with feed pump (CRDI) working condition mounted on MS frame. Piston displacement 2000 to 2 500 cc Bhp 100 to 120 at 4000-6000rpm
01 01 01
4.
CUT SECTION MODEL OF TWO STROKE SINGLE CYLINDER ENGINE
Cut section model of 2-stroke, single cylinder petrol engine working condition mounted on board
01 01 01
5. CUT SECTION MODEL FUEL INJECTION PUMP
4-cylinder diesel engine in-line type and rotor type each.
01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
2
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
6. TEST RIG FOR SINGLE CYLINDER FOUR STROKE ENGINE
Diesel engine with valve timing attachment 01 01 01
7. CUT SECTIONED MODEL OF WANKLE ENGINE
3-lobe with inlet and transfer ports Mounted on board.
01 01 01
8. 8 FOUR GAS ANALYZER WITH INBUILT PRINTER
Portable with LCD display compatible for Nox, Sox, HC, Co both petrol and diesel engines
01 01 01
9. 9 SMOKE METER WITH INBUILT PRINTER
Digital portable With LCD display. 01 01 01
10. 10
CUT SECTION MODELS OF DIFFERENT AUTOMOBILE PARTS AND ACCESSORIES
Starter motor, distributor, dynamo, carburetor, mechanical and Electrical fuel pump, shock absorber, ignition coil, brake cylinder, master cylinder, water pump, FIP (inline& rotary type), injectors, radiator, catalytic converter, battery, turbo charger, air cleaner.
01 01 01
11. 13
SOCKET SET Set at 20 pcs in a box 02 02 02
12. 14
ADJUSTABLE SPANNER Length 300mm, max opening 33mm 03 03 03
13. 15
TORQUE WRENCH Dial type, length 30-50 cm, heavy duty up to 100ft. lb
03 03 03
14. 23
ALLEN KEY Set of 10 pcs from 1.5mm to 10mm 02 02 02
15. 24
TWIST DRILLS SET 4mm to 20mm 03 03 03
16. 25
TAPSET Tap & die set inbox 02 02 02
17. 27
BENCH VICE 4 inch , 5 inch and 6 inch each 04 each 04 each 04 each
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
3
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
18. 28
DIGITAL TACHOMETER With flexible hose to give access in restricted spaces, high quality dial gauge caliburated 0-to 1000psi
02 02 02
19. 29
FEELER GUAGE Strip type having various strips of different thickness from 0.1mm to 5mm
02 02 02
20. 34 PLUG SPANNER For all type of spark plugs 03 03 03
21. 35 TECHOMETER
Diesel tachometer with high accuracy from 0-10000RPM complete with testing
leads 12x24 volt operation
03 03 03
22. 36 PISTON Set of different sizes in a box 01 01 01
23. 37 CONNECTING ROD Set of different sizes 01 01 01
24. 38 CAMSHAFT Maruati Engine 01 01 01
25. 39
INJECTOR
CLEANER & TESTER
Computerized injector cleaning and testing machine with universal manifold
design for all types of mpfi injectors and programmable injector pulse mode with
in rpm 500 to 9900.
02 02 02
26. 40
CUT OUT
SECTIONED MODEL OF FOUR CYLINDER PETROL
ENGINE
4-stroke-4-cylinder water cooled engine fitted on steel frame operated by motor at slow speed
01 01 01
27. 44 PISTON RING
EXPANDER
Self locking HD, high 80 mm, capacity
85t0175 mm (RC-4) 02 02 02
28. 4PISTON RING For installing and removing rings without 02 02 02
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
4
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
5 COMPRESSOR risk of breaking, distortion and other
risks (RE-004)112 to 175 mm.
29. 46
CUT SECTION
WORKING MODEL CONSTANT MESH
Suitably sectioned to show the details of
gear mechanism of forward and reverse speeds. Complete unit is mounted sturdy
iron frame.
01 01 01
30. 47
CUT SECTION
WORKING MODEL
SLIODING MESH
GEAR BOX
Suitably sectioned to show the details of gear
mechanism of forward and reverse speeds.
Complete unit is mounted sturdily iron frame 01 01 01
31. 48
CUT SECTION
WORKING MODEL
SYNCHROMESH
GEAR BOX
Suitably sectioned to show the details of gear
mechanism of forward and reverse speeds.
Complete unit is mounted sturdily iron frame 01 01 01
32. 49
CUT SECTION
WORKING MODEL
AUTOMATIC
TRANSMISSION OF
A CAR
Suitably sectioned to show the details of gear
mechanism of forward and reverse speeds.
Complete unit is mounted sturdily iron frame. 01 01 01
33. 50
CUT SECTION
WORKING MODEL
OF DIFFERENTIAL
Actual cut section of rear axle assembly with
differential gear fully floating type 01 01 01
34. 51
CUT SECTION OF
WORKING MODEL
OF GEAR BOX WITH
DIFFERENTIAL
(TRAN AXLE)
Differential gear assembly actual cut section
assembled on a square iron frame all
necessary parts shown
01 01 01
35. 52
WORKING MODEL
OF STEERING
SECTION
Rack and pinion type & worm and roller type
mounted on a single big board. 01 01 01
36. 53 WORKING MODEL
OF POWER
Hydraulic power steering system motorized
actual working 01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
5
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
STEERING SYSTEM
37. 54
WORKING MODEL
OF SUSPENSION
SYSTEM
Complete both side MACPHERSON suspension
strut with drive shaft, disc brake. 01 01 01
38. 55
WORKING MODEL
OF HYDRAULIC
BREAK UNIT
Actual working model hydraulic drum brake
(4 drum) 01 01 01
39. 56 PROPELLER SHAFT
Propeller shaft with universal joint and yoke
fitted on steel stand with differential and axle 01 01 01
40. 57 SPRING TESTING
INSTRUMENT
Spring load capacity 0-200kg, dia 51 mm,
length admitted 140 mm 01 01 01
41. 58
CUT SECTION
MODEL OF
MECHANICAL JACK
1 ton capacity 01 01 01
42. 59
CUT SECTION
MODEL OF
HYDERAULIC JACK
1 ton capacity 01 01 01
43. 60
WORKING MODEL OF CUT SECTIONED TRANSFER CASE ASSEMBLY
Actual parts assembled on a sq iron piece for demonstration purpose
01 01 01
44. 61
SECTIONED MODEL OF AIR BRAKE SYSTEM
Air break actual working with motorized air compressor consisting of air tank, air booster broke shoe brake drum etc
01 01 01
45. 62
CUT SECTIONED MODEL CLUTCH SYSTEM
working model of claw clutch, conical frictional I clutch, single plate clutch, centrifugal clutch multi-plate clutch coil spring type single plate clutch each
01 01 01
46. 63
MODEL OF MECHANICAL BRAKE SYSTEM
Mechanical disc brake working model complete on base with lever
01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
6
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
47. 65
EXHAUST GAS ANALYZER WITH PC
Features 32 bit microprocessor based exhaust Gas Analyzer, Easy to use bench top design, declaration of conformity to OIML, Class 9 (ISO 3930) ideal for fault finding and regulated testing measures, CO,HC.CO2, 02 and Lambda, Fast warm up time and fast response time, RPM and Oil Temperature Measurement, Print result via RS.232 and CNG vehicles. Product standard: OIML Class 0, ISO 3930 PC with monitor 21” & colour printer to be supplied as std accessory Measured Gases: Using NDIR bench CO/CO2/HC Using Electrode-Chemical Cells. O2 Lambda: -0.5—2.0 Power Supply: 100-300 v/1 ph/50-60 Hz RPM: 2.4 stroke, DIS,2-12 cyl Warm up time 120 sec: Fuel types: Petrol, LPG, CNG: Weight 5 Kg Approx.) Probe Insertion Length: 300mm, Ambient Operating Range + 5 deg to +45 deg ARAI approved, CE certified & ISO certified
01 01 01
48. 72
WHEEL ALIGNER
Measuring parameters, Range & Accuracy Technical Features
Accuracy
Measuring Range
Total Range 01 01 01
Front Axle
Total Toe +/- 2” +/- 2 deg +1-5 deg Partial Toe
+/- 1’’ + /-1 deg +/-2 deg
Set back +/-2” +/- 2 deg +/- 5 deg
Camber +/- 2” 1/- 3 deg +/-10 deg Caster +/- 7” +/- 10 deg +/-18 deg Rear Axle Total toe +/- 2” + /-2deg + /-5deg
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
7
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
Partial Toe
+/- 1’’ +/- 1 deg + /-2 deg
Camber +/- 5” +/- 3 deg + /-10 deg Thrust Angle
+/- 2” +/- 2 deg +/- 5 deg
Power Supply 220— 230 volt AC 50 Hz. branded computer with printer, latest accurate CCD technology with 8 CCD sensor with infra red communication between sensors & Bluetooth data transfer from measuring head to the system, se If extend & renew a automobile data, diagnostic messages, shows service station name, address, vehicle No. & mileage can be printed with test results, toe curve program automatic spoiler program, online correction of camber, caster & toe with graphical display, inbuilt data storage software for vehicle history, summery & comparison of diagnostic repair values on single screen, big wheels for easy movement, simple calibration with 3D, self Calibration, caster compensation & steering angle Self calibration for easy understanding of the operation, preloaded with live demonstration software, edit option for wheel size for automatically calculation of toe value.
49. 73
WHEEL BALANCER
Wheel Dia standard = 10” to 20”, operating pressure=100: 175 PSI, Bead Breaking force=2800 kg, electric Motor=220v/440v 50HZ, Dimension=1300 x 850x 800, clamping pneumatic with 4 jaws complete. CE certified & ISO certified
01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
8
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
50. 74
TYRE CHANGER
Wheel Dia standard = 10” to 20”, operating pressure =100:175 PSI, Bend Breaking force=2800 k electric Motor=220v/440v 50HZ, Dimension=1300 x 850x 800, darn ping pneumatic with 4 jaws complete. CE certified & ISO certified
01 01 01
51. 75
TYRE INFLATOR Twin hose assembly with wall mounted dial gauge 01 01 01
52. 76
INVERTED METALLURGICAL MICROSCOPE
inverted metallurgical microscope having co-axial, coarse and fine motion assembled on ball bearing guides, equipped with horizontal illuminator with centering provision, field and aperture diaphragm and slots for dropping filters. Built in base variable solid state transformer. Large sturdy stage with X-y axis movements. coarse and fine focusing knobs, supplied with two colored filters in metal mount, raxine cover, complete inbox. Eye Piece: WF 10X (Paired) and Objective .M5x, M 10x,M20x, M40x/M45x
01 01 01
53. 77
TURBO CHARGER, VARIABLE TURBO CHARGER;
Made out of full size original parts, suitably sectioned and to demonstrate the working of turbocharger is mounted on a suitable base (Brand New)
01 01 01
54. 78
WORKING MODEL OF TORQUE CONVERTER
Made out of original new part, will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a wooden base.
01 01 01
55. 79
SUSPENSION & STEERING SYSTEM
Made out of full size new original parts, suitably
sectioned and to demonstrate the working of suspension and steering system. The model will be
01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
9
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
TRAINER mounted on a tubular frame, suitable colour
imported painting will be carried out along with Miracle coating for the model will be done for extra gloss and shine. The painting will be carried out in
such a way that different colours will be use for different components such as identification of sectioned area etc according to the colours code for easy identification of different systems and
mechanism (Brand New)
56. 80
TANDEM MASTER CYLINDER WITH BOOSTER
Cut section model with required Accessories Suitably painted and mounted on a wooden board (Brand New)
02 02 02
57. 81
WHEEL CYLINDER Cut Section model with required accessories
suitably painted and mounted on a wooden board (Brand New)
02 02 02
58. 82
AIR BREAK ASSEMBLY
Made out of new parts such as Air Compressor,
Unloaded value, foot value, Booster, Wheel assembly, air tank, control value etc. The Brake system will be fitted with two front wheel assembly complete (with out axle) and the drum will be suitably sectioned to show the working of the brake shoe. Other system will be mounted as it is and will be made to function (foot brake, hand
brake etc will be functional) the entire system will
be mounted on a sturdily iron frame. A.F.H.P Single phase 220/230 V AC Motor will be coupled to the compressor for generation of the air, which is used for the operation of the model (Brand New)
02 02 02
59. 83
BREAK TESTING EQUIPMENT
To test efficiency of vehicle where motion after break is plotted.
01 01 01
60. 84
GRINDING MACHINE (GENERAL PURPOSE)
D.E pedestal with 300 mm dia wheels rough & smooth
02 02 02
61. 85
OXY-ACETYLENE WELDING EQUIPMENT
Ith complete accessories (Low & high pressure) 01 01 01
62. 8SPOT WELDING Universal welding station with pneumatic gun of 01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
10
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
6 MACHINE WITH COMPLETE ACCESSORIES
10 KVA capacity having 2 program with optional
water cooling feature, supply three phase, maximum power 50 Kva, short circuit secondary current 8 KA, no load voltage 8V, dimension
60x68x100, wt 120 kg, net wt. 105 kg. protection degree 21, thermal class F, delayed fuses 25 amp.
63. 87
GAS WELDING TABLE Size: 1220 mmx760 mm 01 01 01
64. 88
CYLINDER BLOCK CI ENGINE OVERHEAD CAMSHAFT & CAMSHAFT IN BLOCK AIR COLLED
Model with required accessories suitably
painted and mounted on a frame 01 01 01
65. 89
CARBURETOR Solex, Mikurny for dismantling & assembling 02 EACH 02 EACH 02
EACH
66. 90
SPARK PLUG CLEANING & TESTING EQUIPMENT
Glow plug tester 12 volt heater plug,
connection self test (green) condition of the
glow plug is indicated with good (Green)
defective (red) test result in less than 15
seconds, the test may be executed with glow
plugs.
02 02 02
67. 91
DEMONSTRATION BOARD OF MPFI ENGINE
This open demonstration board is made out
of original parts such as petrol injector, inlet
manifolds, throttle body, distributor, ECU,
canister purge valve, carbon canister, fuel
tank module, supporting sensors such as
lambda sensor, engine speed sensor, cam
position sensor etc. with necessary wiring
connection to show the circuit connections.
The entire system will be suitably sectioned
and mounted on Navopan board.
01 01 01
68. 92
AIR CONDITIONER TRAINER KIT
Made out of original parts, will be suitably
sectioned and arranged to demonstrate the 01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
11
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
internal construction details showing the
minute information such as AC compressor,
condenser, radiator, its pipe lining ,
blower/fan assembly etc. the model will be
suitably painted out and the entire model is
mounted on a sturdy iron frame (Band New)
69. 93
FUNCTIONAL EXPERIMENTAL MODEL OF DIFFERENT TYPE OF SENSORS
This open demonstration Board is made out
of original parts with necessary wiring
connection to show the circuit connections.
The entire system will be suitably sectioned
and mounted on Navopan Board.
01 01 01
70. 94
AIR COMPRESSOR
2 stage twin cylinder air cooled reciprocating
type, driven by 7.5 HP 3 phase motor with
pure cast iron 175 PSIG operation, 250 ltr
tank with 5o mtr heavy duty air pipe, nozzles
& clamps complete
01 01 01
71. 95
LIFTING JACK (SCREW TYPE)
1000 to 1500 kg capacity ISO certified
company. 02 02 02
72. 96
MULTI POINT FUEL INJECTION PUMP
Common rail for 4-cylinder engine. 01 01 01
73. 97
BATTERY 12 VOLT LEAD ACID FOR MOTORCYCLE, SCOOTER, TAR & TRUCK
Sea led Maintenance Free Batteries only 02 02 02
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
12
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
74. 98
COMPUTERIZED UNIVERSAL TESTING MACHINE
The Computerized machine must be able to conduct various types of tests on ferrous and non ferrous materials in Compression, Tension, and Transverse Bending. The machine should have three main parts viz. Loading frame, hydraulic pumping system and electronic control pane. The machine should be hydraulically operated. The Power- Pack should have directly driven hydraulic pump to gene rate continuous non-pulsating flow of oil to ensure very smooth load application. All necessary equipments like oil filter, oil Strainer, air breather, oil level indicator, drain plug, flow control valve etc. shall be provided in the power pack. The machine shall be provided with overload safety. The load measurement should be computer controlled. The supplier shall provide a Personal Computer based data acquisition system with software and printer which shall run a variety of mechanical tests as duly specified, recall data from previous tests and prepare reports. Test reports and graphs shall be sent directly to the printer via parallel port. The Personal Computer shall have Intel i5 or above processor, 4 GB RAM, 17” TFT monitor, pre loaded with software. The Loading frame should have heavy cast iron base. All the motors/electrical items should be of standard make. Operation and Maintenance manual for performing standard tests must be supplied with the machine. The Software should have following features 1. Peak load along with online load
01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
13
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
2. Max. elongation with online elongation 3. Graphical display of Load vs. Time 4. Graphical display of elongation vs. time 5. Graphical display of Load vs. elongation 6. Complete statistical Analysis 7. Data Report Management TECHNICAL DATA Minimum Capacity 600 KN Power Supply 3-phase load range with accuracy of measurement + 1 % of indicated load Strain accuracy + 0.05 % of full scale least Count (Resolution) 0.05 KN Max. Clearance for Tensile Test 50-800 mm Max. Clearance’ for Compression Test 0-800 mm Straining/Piston at no load 0-100 mm Electric Supply motor 1.9 KW or above With standard Attachments
75. 99
TOOL KIT-5 DRAWER
LIST OF TOOLS SET 344 PCS WITH TROLLEY 5 DRAWER
01 SET 01 SET 01SET
¼” DRAVE 74 PCS SOCKET COMBINATION SET
12pcs ¼” DRAVE 6PT Socket: 4,5,5,5,6,7,8,9,10,11,12,13,14mm
12pcs ¼” DRAVE 6PT Socket: 5/32”,3/16”,7/32”,1/4”,9/32”, 5/16”, 11/32”, 3/8”, 13/32”, 7/16”, 15/32”, ½”
12pcs ¼” DRAVE 6PT deep Socket: 4,5,5,5,6,7,8,9,10,11,12,13,14mm
06 pcs ¼” DRAVE STAR Socket: E4,E5,E6,E7,E8,E10
11 pcs ¼” DRAVE STAR Socket Bit: T6,T7,T8,T9,T10,T15,T20,T25,T27,T30,T40
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
14
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
04 pcs ¼ DRIVE Philips Socket Bit PH.0, PH.1, PH.2, PH.3
03 pcs ¼” DRAVE Slotted Socket Bit:4,5,5,6,5 2 pcs ¼” DRIVE extension Bar:2”, 4” 1 pcs ¼” DRIVE Flexible extension Bar6” 1 pcs ¼” DRIVE Universal Joint 1 pcs ¼” DRIVE Screw driver Bar 1 pcs ¼” DRIVE Sliding T Bar 1 pcs ¼” DRIVE Ratchet (Plastic holding) 3/8” DRIVES 8 pcs SPARK PLUG SOCKET SET 1 pcs 3/8”’DRIVE Torque Wrench 10-80 FT/LB
1 pcs 3/8” DRIVE Flexible Ratchet (Plastic holding)
L pcs 3/8” DRIVE Stubby Ratchet (Plastic holding)
2 pcs 3/8” DRIVE Wobble Extension Bar 1-314,10”
1 pcs 3/8” DRIVE Magnetic spark Plug Socket 14mm
2pcs 3/8” DRIVE Magnetic spark Plug Socket 16mm. 21mm
3/8” DRIVE 23 P08 SOCKET SET
16 pcs 3/8” DRIVE. 6 PT Socket : 6,7, 8,9,10,11,12,13,14,15,16,17,18,19.21,22 mm
3 pcs 3/8” DRIVE extension Bar 1-3/4”, 3’,6” 1 pcs 3/8” DRIVE Universal Joint L pcs 3/8” DRIVE Sliding T Bar 1 pcs 3/8” DRIVE Professional breaker Bar
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
15
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
1 pcs 3/8” DRIVE Ratchet (Plastic holding) 40 pcs STAR BIT SET (TAMPER PROOF)
10 pcs 9 in 1 star Key Set (temper Proof T10H, T15H, T20H, T25HT27H, T30H, T40H,T45H, T50H+Handle
9 pcs Long Ball Point Hex Set H1.5 H2, H2.5, H3, H4, H5, H6, H8, H10
9 pcs 1/4” DRIVE Star Socket Bit Set (Tamper Proof) TS10H,TS15H, TS20H, TS25H, TS27H, TS3OH, TS40H, TS45H, TS50H
6 pcs ¼” DRIVE Star Socket Bit Set (Temper Proof):T10H, T15H, T20H. T25H. T27H. T30H
3 pcs 3/8”DRIVE Star Socket Bit Set (Temper Proof): T4OH. T45H, T50H
3 pcs ½” DRIVE Star Socket Bit Set (Tamper Proof): T55H, T60H, T70H
½” DRIVE 8 PCS ACCESSORY SET 4 pcs ½” DRIVE Extension Bar 2”, 3”,5”, 10” 1 pcs ½” DRIVE Universal Joint 1 pcs ½” DRIVE Professional Breaker Bar 15” 1 pcs ½” DRIVE Sliding T Bar 12” 1 pcs ½” DRIVE Ratchet (Plastic holding) ½” DRIVE 22Pcs SOCKET SET (6PT)
22pcs
½” DRIVE 6PT. Socket 8,10, 11, 12,13, 14, 15, 16, 17, 18, 19,20,21,22,23,24,25,26,27,28,29,30,32mm
½” DRIVE 17 Pcs DEEP SOCKET SET
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
16
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
17 pcs ½” DRIVE 12PT.Deep Socket :10.11, 12,13.14,15,16, 17,18,19, 21 ,22,23,24,27,30.32 mm
½” DRIVE 24 PCS STAR COMBINATION SET
9 pcs ½” DRIVE Star Deep Socket: E10, E11, E12, E14, E16, E18, E20, E22, E24
6 pcs Star Wrench: E6 x E8, E7 xE11, E10x E12, E44xE18, E16XE22, E20xE24
1/2” DRIVE 15 Pcs DEEP IMPACT SOCKET SET (6PT)
15 pcs ½” DRIVE 6PT Deep impact Socket :10,12,13,14, 15,16,17,18, 19,21,22,24,27,30,32 mm
½” DRIVE 22 Pcs IMPACT SOCKET SET
21 pcs ½” DRIVE 6PT Socket 8,10,11,12,13,14.15, 16,17,18,19,21 22,23,24,25,26,27,29,30,32mm
1 pcs ½ ” DRIVE impact Joint
½” DRIVE 18PCS IMPACT BIT SOCKET SET (6PT)
8pcs ½” DRIVE Star Impact Socket T25,T27,T30,T40,T45,T50,T55,T60
8pcs ½”DRIVE Hex Impact Socket: H5,H6,H8,H10,H12, H14,H17,H19
1 pcs ½” DRIVE Spline Impact Socket Tamper Proof) : M16H
1 pcs ½”DRIVE SpIine Impact Socket : M14 5 pcs COMBINAT1ON TOOL SET 1 pcs Ball Pein Hammer 1-1/2P
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
17
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
1 pcs I pcs Stainless Scissor 8” 1 pcs pcs Magnetic Bar 3.5 LBS 1 pcs pcs Flexible Shaft Nut driver 7mm 1 pcs Door Upholstery Remover 8 pcs 75* OFF set Box Wrath Set
8 pcs 75* off set box wrench 6x7, 8x9.,10x11,1 2x13, 14x15,1 617,18x1 9, 22x24
8 pcs COMBINATION WRENCH SET (EURO-TYPE)
8 pcs Combination wrench (Euro type): 24, 25, 20, 27, 28, 29, 30, 32 mm
17 pcs Combination Wrench (Euro Type)
17 pcs Combination Wrench (Euro Type) 6,7,8,9,10,11,12, 13,14,15, 16,17,18,19,21,22,23mm
8 pcs FLARE NUT WRENCH SET (MIRROR-FINISH)
8 pcs Flare nut wrench 8x9, 10x 12, 11 x13, 14x1 7,16x1 8, 17x19, 3/8” 7/16”,1/2” x 9/16”
2 pcs Flare nut wrench 10x1 1, 10x12 mm
10 pcs HEAVY DUTY SCREW DRIVER SET 3x75L, 5.5x75L, 6.5x38L, 6.5x100L, 8x150L, 0x75L, 1x75L, 2x38L, 2x100L, 3x150L,
9 pcs STAR SCREW DRIVER SET T8, T9, T10. T15, T20, T25, T27 T30, T40
3 pcs Plier SET 1 pcs adjustable gauged wrench 10” 1 pcs Water pump Plier 10”
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
18
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
1 pcs Locking pliers 10” 4 pcs PLIER SET 1 pcs long nose plier 8” 1 pcs bent long nose plier 8” 1 pcs Diagonal plier 7”
1 pcs Slip joint plier
76. 100
DRIVING SIMULATOR
A versatile indoor training simulator for imparting basic and advanced driving skills. • Ideal for teaching driving to notice drivers test drivers of different experience level conduct refresher training for out of touch drivers. • Configurable for light, Medium and heavy vehicles with either left or right hand driving options. • 120o degree coverage, three monitors, original seat, realistic controls, dashboard assembly, safety belt, gauges, transmission and instrumentation gives real feel. • 30 CGI driving scenes of different types of roads, traffic, terrains and environmental conditions with rear and side view mirror insets. • Recording/playback of faults committed by the trainee. • The trainer can inject on-line faults and obstacles to assess the reactions. • Basic system has one instructor station and one driver station. Upto 10 driver station can be controlled by one instruction station. Environmental conditions like rain, fog, snowfall, intensity of light can simultaneously be created.
02 02 02
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
19
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
Reputed brand only)
77. 101
IMPACT TESTING MACHINE (LZOD)
Impact Tester is designed for conducting CHARPY, IZOD AND IMPACT Test. The test Method confirm to IS: 1973, and IS 1499-1977, and BS: 131 Part 2 & 3-1972 IS: 1598-1977, BS; 131 Part 1- 1972. The impact energy absorbed by the specimen during rupture is measured as the difference between the height of drop before rupture and the height of rise after rupture of the
01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
20
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
test specimen and is read on the dial scale.
78. 102
TORSION TESTING MACHINE
Designed for conducting Torison and Twist Tests on various metal wire, tubes sheet materials. Torque Measurement by pendulum Dynamometer System. Torque ranges can be adjusted. Torque can be applied to specimen by geared motor through gear box, Autographic recorder to be provided to know the relation between torque and angle of twist Capacity 20Kgm. Grip for round bar-7-20mm and Grip for flat 3-10mm Clearance bet. Grips -0-450mm
01 01 01
79. 103
ROCKWEL HARDNESS MACHINE
With automatic zero setting dial gauge and automatic load selection. Calibrated weight set 60,100,150 kgf steel ball indentor 1/16” (01 No.) Diamond cone indentor 120 deg ( 01)Test Block-B and Test Block-C (01 each)
01 01 01
80. 104
BRINELL HARDNESS TESTER
All the necessary parts of a lubrication system of a car are shown in actual working form. This model helps the student to understand the working of the lubrication system of a car very easily. it is specially made dissectible for demonstration purpose.
01 01 01
81. 105
WORKING MODEL OF COOLING SYSTEM OF AN AUTOMOBILE
Actual Working Model of Cooling System of an Automobile with Brand New Radiator, Water tank with Inlet outlet Connection & Hoses Water Pump Connected with Motor Mounted on frame
01 01 01
82. 10
LUBRICATION SYSTEM OF AN AUTOMOBILE
All the necessary parts of a lubrication system of a car are shown in actual working form. This model
01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
21
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
6 (CUT SECTIONAL) helps the student to understand the working of the lubrication system of a car very easily. It is specially made dissectible for demonstration purpose.
83. 107
SPRING TESTING MACHINE
of Capacity 50 Kgm with Digital Load Indicator, Digital Length Indicator
01 01 01
84. 108
HYDRAULIC JACK 5 ton capacity 01 01 01
85. 109
IMPACT WRENCH Extra heavy duty ½” 01 01 01
86. 110
MINI IMPACT WRENCH H D 3/8” 01 01 01
87. 111
MECHANICAL CREEPERS
Imported with nylon wheels adjustable and head rest
01 01 01
88. 112
PORTABLE JACKS Quick action hydraulic for light vehicles. 01 01 01
89. 113
COMPRESSION GAUGE Engine compression tester with attachments pressure hose and extension
01 01 01
(“Group F”) Detailed Tender Notice No. DTE/PUR/14/328 Dated 16-10-2014 Automobile Engineering Department
22
S. NO NAME OF THE ITEM REVISED SPECIFICATIONS
QUANTITY REQUIRED FOR Unit cost to be
quoted KUPWARA UDHAMPUR SAMBA
90. 114
CAR WASHER
H 10k Pressure Hot & Co Car Washer 130 Bar at 10 1pm, the unit shall have 3 ceramic pistons, dry vertical boiler with diesel oil rid crank pump pressure control device, total stop device) thermic switch for motor protection, thermostat for temperature setting, low pressure detergent intake from the built in tank CE certified & ISO certified
01 01 01
91. 115
TWO POST LIFT
Lifting capacity 3 ton, load distribution (F:R) =3:2 lifting time =45 sec, max wheel width=2075 mm ,max lift=1750mm length l050mm electric motor = 3kw/4h p, overall I diminutions=2700x3200x1280
01 01 01
92. 116
TYRE VULCANIZING MACHINE
Valcanizer with double ended plate for H .D jobs, with air operated system to close the plates, pressure governor (0-12bars) with 60 min timer, dimensions=490x200 x1000 m m, weight, 35 kgs.
01 01 01