group engineer’s hand tools 518 · 2016. 4. 25. · chuck body: held in the spindle using a...
TRANSCRIPT
Edge & Centre Finder - 5 Piece Set Consists of a chuck body and four contact arms. Designed to check‘run-out’ or concentricity, straightness and alignment. Will indicatethe position of a datum point on a component or fixture from thecentre line of a machine spindle. Suitable for use on drill presses,lathes, milling machines, borers etc.
Chuck Body: Held in the spindle using a suitable drill chuck or collet chuck (fig 1).The contact arms are retained in position using the knurled collarwhich lightly clamps the ball joint inside the body. Arms may beexchanged without the need to remove the body from the machinespindle.
Universal Indicator Holder The detachable end will allow clamping with 2and 3 piece dovetail clamping assemblies andwhen removed will fit standard 1/4” side clamp. This uses the spindle centre line to aligncomponent bores or spigots, check the flatnessor squareness of workpieces or fixturing andcheck run-out of components. The spindle shouldonly be rotated manually to avoid damaging thedial test indicator (fig 1).
Needle PointTo lightly mark out lines andpositions on a component asa guide to subsequentoperations, using themachine’s dials or digitalread-out to position thescriber point (not illustrated).
Page373
ENGINEER’S HAND TOOLS
GROUP
518H
AN
D TO
OLS
Flat Work-Piece
Convex Work-Piece
Ball Contact
Disc Contact
Needle Point
Universal Indicator Holder
ChuckBody
Position the contact arm in line, but slightly away from the surface tobe aligned. When finding the surface of a diameter, the ‘Disc' mustbe positioned as near to the centre of that diameter as possible. Run the spindle between 200 and 500 revs/min. The table or spindle is then moved slowly, to bring the contact arm closer to thesurface to be aligned. The contact arm will tap lightly against thesurface (fig 2) the movement of the arm will become less and lessthe nearer the datum point gets to the spindle centre line (fig 3).When the arm stops spinning in a straight line and starts to 'jump',this indicates the datum point (fig 4):
1/2 contact dia + Edge = Centre 1/2 contact dia - Centre = Edge
fig 2 fig 3 fig 4
fig 1
Disc Contact .100”
Used to find a datum point .050” ± .0005” away from a convexsurface.
Ball Contact .250”
Used to find adatum point .125”± .0005” away from a flat surface.
ContentsWeight Order Codeeach KEN-518
As Above 130g -1500K
ClampingAssemblies
2 Piece 3 Piece
Description DiameterWeight Order Codeeach KEN-518
Shank 0.200”60g -1460KBody 0.500”
Edge & Centre Finders
Cylinder TypeFor fast accurate work location. Made from toolsteel and hardened all over, they can be used onflat surfaces, straight edges, shoulders, grooves,studs, dowels, centre points and scribed lines.
To locate an edge first secure the finder in a colletor chuck, the work table is then traversed to causethe rotating edge finder to make contact with theworkpiece. (fig 1).
Upon touching the workpiece the edge finder’scontact point will be forced into runningconcentrically with the body (fig 2). Any furthermovement to ‘off-centre’ will cause a distinctwobble.
At this point, the distance from the work edge to thecentre of the finder is equal to half the diameter ofthe contact point. Datum lines and centre points arelocated using the combination edge and centrefinder (fig 3).
This has a cone shaped contact point which islowered into position barely touching the workpieceat the point you wish to measure. The finder is made to run concentrically using asteel rule or straight edge (fig 4).
Edge & Centre FindersCombination
Double Edge
Plain Edge
Description DiameterWeight Order Codeeach KEN-518
Shank 0.200”50g -1440KBody 0.500”
Shank 0.200”30g -1450K
Body 0.375”Shank 5mm
40g -1445KBody 12mm
Edge Finders
fig 2
fig 3
fig 4
fig 1
Description DiameterWeight Order Codeeach KEN-518
Shank 0.500”60g -1470KBody 0.500”
Shank 12mm50g -1480K
Body 12mm
Description DiameterWeight Order Codeeach KEN-518
Shank 0.200”Body 0.375” 30g -1410K
Shank 10mmBody 10mm 40g -1420K
Shank 0.200”Body 0.500” 40g -1430K
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Engineer’s Rule Round End - Pocket Type
Spring tempered stainless steel blades. 12mm blade width withpocket clip/depth gauge slide. Reverse side is marked with 1/64” tomm conversion table.
ENGINEER’S HAND TOOLS
GROUP
518
Page374
HAN
D TO
OLS
ScaleLength
Order CodeType KEN-518
150mm/6” -3110KMetric 300mm/12” -3310K& Inch 600mm/24” -3710K
1000mm/39” -3910K150mm -3130K
Metric 300mm -3330Konly 600mm -3730K
1000mm -3930K
Engineer’s Steel Rules
Finest quality spring tempered stainless steel. Satin chrome. Anti-glare finish with permanent black figures and graduations. Extremely easyto read. Accuracy: ± 0.2mm full scale. Constant at 20°C. Rustless.
Round End - Rigid BladeSpring tempered rigid steel blades. 150mm/6” = 19mm blade width. Other lengths = 25mm blade width.With hanging hole.
Square End - Flexible BladeSpring tempered flexible steel blades. 12mm blade width.
Square End - Rigid BladeSpring tempered rigid steel blades. 150mm/6” = 19mm blade width. 300mm/12” = 25mm blade width.
Engineer’s RuleRound End - Pocket Type
Spring tempered stainless steel blades. 13mm blade width withpocket clip/depth gauge slide. Reverse side is marked with 1/64” tomm conversion table. 12mm blade width. Can also be used as adepth gauge.
EEC Class 1
ScaleLength
Order CodeType KEN-518
Metric 150mm/6” -3010K& Inch 300mm/12” -3210KMetric 150mm -3030K
only 300mm -3230K
ScaleLength
Order CodeType KEN-518
Metric 150mm/6” -3020K& Inch
ScaleLength
Order CodeType KEN-518
Metric 150mm/6” -3120K& Inch 300mm/12” -3320K
ScaleLength Order Code
Type KEN-518Metric 150mm/6” -3510K& Inch
ScaleLength
Order CodeType SEN-518
Metric 150mm/6” -3500K& Inch
Flexible Blade - Inch - subdivided to 1/16”, 1/32” and 1/64”, figured every inch.
Flexible Blade - Metric - subdivided to 0.5mm and 1mm, figured every 10mm.
Rigid Blade - Metric - subdivided to 0.5mm and 1mm, figured every 10mm.
Rigid Blade - Inch - subdivided to 1/16”, 1/32” and 1/64”, figured every inch.
Flexible Blade - Metric - subdivided to 0.5mm and 1mm, figured every 10mm.
Flexible Blade - Inch - subdivided to 1/16”, 1/32” and 1/64”, figured every inch, every 8/64”, and every 4/32”.
Rigid Blade - Metric - subdivided to 0.5mm and 1mm, figured every 10mm.
Rigid Blade - Inch - subdivided to 1/16”, 1/32” and 1/64”, figured every inch, every every 8/64”,and every every 4/32”.
Round End
Square End
Stainless Steel
Rustless
Anti Glare Satin Chrome
Rustless
Round End - Flexible BladeSpring tempered flexible steel blades. 12mm blade width. With hanging hole.
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Anti Glare Satin Chrome
Rustless
Anti Glare Satin Chrome
Rustless
ENGINEER’S HAND TOOLS
GROUP
518
Page375
HAN
D TO
OLS
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Length Weight Order Codeeach KEN-518
600mm/24” -2950K
Carpenter’sRules
Extremely lightweight extrusion made from anodised aluminium,hardened and lacquered. Graduated mm/1/8”. Supplied in clearplastic wallets.
Measured Weight Order CodeLength each SEN-518
150mm/6” 33g -3600K
300mm/12” 62g -3620K
600mm/24” 124g -3640K
1000mm/39” 191g -3660K
Range Weight Order Code(mm) each KEN-518
1 - 15 18g -1320K15 - 30 36g -1340K
TweezersFor workshop and home use. Cross pattern types are selfclosing and open only under applied pressure. High qualityfinish supplied singly or as a six piece set.
Bent Nose
Needle Nose
Sharp Nose
Flat Blade
Sharp Nose Cross Pattern
Type Length Weight Order Code(mm) each KEN-518
Sharp Nose 115 20g -5100K
Needle Nose 115 20g -5120K
Flat Blade Cross 170 30g -5140K
Bent Nose 145 30g -5160K
Flat Blade 120 20g -5180K
Sharp Nose Cross 115 20g -5200K
Set of 6 (1 of each above) 134g -5250K
Tapered GaugesThese are called taper gauges only because of their shape - they donot measure tapers. They are ideally suited for the rapid accuratechecking of the inside diameters of tubing, slot widths, hole sizes,setting calipers etc. Manufactured from spring tempered steel.0.1mm increments. Rustless. Constant at 20°C. Satin chrome antiglare finish. Permanent black figures and graduations.
Length Weight Order Codeeach KEN-518
600mm/24” -2980K
Line of Chords RuleThis precision tool has a line of chords scale for use in measuringangles and in determining the circumference of a circle from adiameter measurement. The rule is flexible and rustless with deepetched figures filled with black ink.
Length Weight Order Codeeach KEN-518
1m/36” -4540K
Brass Counter Measure
A robust measuring tool manufactured from hard rolled brass with permanent black figures and graduations. Flexible and rustless, it has a 19mm wide blade and countersunk fixing holes.
Flat Blade Cross Pattern
Folding Steel RuleThis folding steel rule is manufactured from spring tempered stainlesssteel with a polished finish and it is both flexible and rustlesss. Astrong, solid performer for the engineer.Subdivided to mm, figured cm one side. Inch - subdivided to 1/16”, figured 1” other side.
NEW
NEW
NEW
Size Weight Order Code(mm) each KEN-51875 ( 3”)* 140g -4620K100 ( 4”)* 270g -4640K150 ( 6”)* 320g -4660K225 ( 9”) 1400g -4680K300 (12”) 2000g -4700K
Engineer’s SquaresManufactured from hardened andtempered steel. The edges are ground parallel to give the square anexact right angle on both the inside and outside of the stock andblade.
Squareness tolerance: 75mm, 100mm and 150mm = +/- 0.030mm,225mm and 300mm = +/- 0.040mm.
*Suppliedin robust case.
Size tol. Order Code(mm) (mm) OXD-340
75 ( 3”) -0030K
100 ( 4”)+/- 0.016
-0040K
150 ( 6”) -0060K
225 ( 9”) -0090K
300 (12”) +/- 0.024 -0120K
Adjustable SteelSquares
Made from hardened steel and precisionground. Supplied with three fully adjustableblades. One plain, parallel blade for use as aconventional engineer’s square, 30° and 45°bevel edged blade for checking angles, and anarrow blade graduated metric and imperial.
Measured Weight Order CodeLength each KEN-518
100mm/4” 340g -4150K
150mm/6” 410g -4160K
Engineer’sSquares
Manufactured from hardened steel that has been precisely ground to produce parallel edges so that the square has an exactright angle on both the inside and outside of the stock and blade, to ensure accuracy. Conforms to BS939 Grade B.
ENGINEER’S HAND TOOLS
GROUP
518
Page376
HAN
D TO
OLS
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Range Length Order Code(mm) (inch) (mm) KEN-518 8 - 12 5/16”- 1/2” 115 -1174K12 - 19 1/2”- 3/4” 115 -1175K19 - 32 3/4”- 11/4” 115 -1176K32 - 54 11/4”- 21/8” 137 -1177K54 - 90 21/8”- 31/2” 137 -1178K90 -150 31/2”- 6” 137 -1179K
SetSupplied in a size marked PVC storage wallet, with stud fastening. Contains 1 of each size A - F inclusive.
Set range:8 - 150mm (5/16” - 6”).
Telescopic GaugesWith knurled satin finish bodies providing positive adjustment of thehardened and radius ground plungers ensuring ccuratemeasurement of theinternal diameter when used with a micrometer.For smaller diameter measurements use the small hole gauge.
Weight Order Codeeach KEN-518
425g -1180K
6PIECES
ENGINEER’S HAND TOOLS
GROUP
518
Page377
HAN
D TO
OLS
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Firm Joint Calipers
Manufactured from high quality steel, with a polishedfinish. Consisting of two legs which are held togetherby a large nut and screw to provide a firm friction joint.Each firm joint caliper has an adjustable ground pointwhich can be retracted for storage and the other leg isangled at the tip. The legs can be reversed, so the tipturns inwards or outwards. Firm joint calipers areused for scribing arcs and parallel lines by usingtheedge of the workpiece as a guide, and are alsoused for measuring from the centre point of acomponent.
InternalCalipers
AdjustablePoint
Adjustable Point & Spur
Size Weight Order Code(mm) each KEN-518
100 (4”) 60g -0530K150 (6”) 80g -0540K
Size Weight Order Code(mm) each KEN-518
130 (5”) 55g -0550K
Internal & External Spring Calipers Manufactured from high quality polished steel with ground finishedpoints. A circular spring bow joins the legs and a fine adjusting screwis mounted across the legs and is used for setting the distancebetween the two points.
Capacity Weight Order Code(mm) each KEN-518
Internal Calipers75 ( 3”) 50g -0230K
100 ( 4”) 50g -0240K150 ( 6”) 90g -0260K200 ( 8”) 110g -0280K255 (10”) 170g -0300K305 (12”) 195g -0320K
External Calipers75 ( 3”) 50g -0430K
100 ( 4”) 50g -0440K150 ( 6”) 120g -0460K200 ( 8”) 120g -0480K255 (10”) 190g -0500K305 (12”) 225g -0520K
Firm Joint Caliper Manufactured from high quality steel, with a polishedfinish. Consisting of two legs which are held together bya large nut and screw to provide a firm friction joint.This firm joint caliper has an adjustable ground pointwhich can be retracted for storage and the other leg isangled at the tip. The legs can be reversed, so the tipturns inwards or outwards. Firm joint calipers areused for scribing arcs and parallel lines by using theedge of the workpiece as a guide, and are alsoused for measuring from the centre point of acomponent.
External Calipers
Spring Divider & Caliper SetContents:6” spring divider, 6” internalcaliper and 6” external caliper.
Number Weight Order Codeof Pieces each KEN-518
3 350g -0580K
Spring DividersManufactured from high quality polished steel. Ground finished points, a fine adjusting screw is mounted across the legs for setting the distance between the two points. A circular spring bow joins the legs, with a knurled extension attached for use when pivoting the dividers. Dividers are used for scribing arcs and circles, alight centre punch mark on the work keeps the pivot leg in the centre while marking.
Capacity Weight Order Code(mm) each KEN-51875 ( 3”) 50g -0030K
100 ( 4”) 60g -0040K150 ( 6”) 95g -0060K200 ( 8”) 115g -0080K250 (10”) 180g -0100K300 (12”) 200g -0120K
3PIECES
ENGINEER’S HAND TOOLS
GROUP
518
Page378
HAN
D TO
OLS
TypeOrder CodeKEN-518
Screw Gauge -0800K
Radius GaugesManufactured from hardened and polished steel, the blades areprecision milled for optimum accuracy when measuring internal andexternal radii. Enclosed in a steel case.
Size range:34Blade Metric: 1.0 to3.0 x .25and 3.5 to7.0 x .532BladeMetric: 7.5 to15.0 x .532Blade Inch: 17/64” to 1/2” x 1/64”30Blade Metric: 15.5 to20.0 x .5 and 21.0 to25.0 x130 Blade Inch: 1/32” to 1/4” x 1/64”.
Screw Cutting GaugeManufactured from hardened and polished steel to check BA,Whitworth and BSF, Acme and American Screw Threads.
Angles: 60° American and Metric, 55° Whit and BSF, 471/2° BA and 141/2° Acme.
Screw Pitch GaugesIdeal for accurately measuring internal and external thread forms.Manufactured from hardened and polished steel, the blades areprecision milled for optimum accuracy. Enclosed in a steel case.Range of sizes:Whitworth - 4 - 62 TPI;Metric - 0.75 - 6mm; American - 4 - 42 TPI.
Type No. of Order CodeBlades KEN-518
55° Whit. 28 -1000K60° Metric 20 -1010K60° USA 30 -1070K
No. of Weight Order CodeBlades each KEN-518
34M 70g -0820K32M 80g -0850K32I 120g -0940K30M 95g -0890K30I 70g -0920K
Depth & Angle Gauges
Plain Type Depth GaugeDesigned for measuring flatbased recesses. Consisting of aprecision ground steel rule andbody which are positioned at 90°
to each other. The body hasprecision ground locating faces,with a knurled adjusting/securing nut.
Protractor Type Depth & Angle GaugeGround steel with graduationsfrom 0° - 180° in both directionsfor fast and accuratemeasurements. When the rule ispositioned to 90° on theprotractor it then providesaccurate measurements of depth.
Protractor typePlaintype
Rule length:150mm (6”)
Type Order CodeKEN-518
Plain -3400KProtractor -3450K
Range of Order Codesizes KEN-518
1.5 - 12.5mm -1130K1/16” - 1/2” -1140K
Drill Gauges Manufactured from hardened steel with a satin finish. Anideal way to quickly measure the diameterof drills and steelwire.
Range of Order Codesizes KEN-518
No. 1 - 60 -1100K
1 - 60 Gauge Measures drill sizes Nos 1 - 60. Holes are marked with size anddecimal equivalent of drill.
Standard Wire GaugesManufactured from high grade tool steel with satinbrushed finish. Each slot is marked with thenominal size. Two part pivoting space savingdesign.
Range of Order Codesizes KEN-518
1 - 36SWG -1160K0.2 - 10.0mm -1165K
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Page379
ENGINEER’S HAND TOOLS
GROUP
518H
AN
D TO
OLS
Double Ended Feeler GaugeHardened and polished taper blades enclosedin a steel case. Blades are clearly marked.Metric & Inch: To BS957: 2008 Part 1 (Inch)and BS957: 2008 Part 1 (Metric).75mm/6” blade length.
Range: 18 Blade: 0.05” - 0.025”.
Number Weight Order Codeof Blades each KEN-51810 55g -0710K13 70g -0740K20 100g -0780K
Number Weight Order Codeof Blades (mm) KEN-51810 40g -0610K18 65g -0650K26 90g -0690K
Inch: Manufactured to BS 957: 2008 Part 1.4” Blade length.Range:10, 18 and 26 Blade:.0015” - .025”.
Thickness Weight Order Code(mm) per 10 KEN-519
12.7mm x 300mm0·03 15g -1030K0·04 15g -1040K0·05 15g -1050K0·06 20g -1060K0·08 25g -1080K0·10 30g -1100K0·15 45g -1150K0·20 60g -1200K0·25 75g -1250K0·30 80g -1300K0·40 120g -1400K0·50 150g -1500K
1/2” x 12”0·0010” 60g -0020K0·0015” 20g -0030K0·0020” 20g -0040K0·0025” 20g -0050K0·0030” 30g -0060K0·0040” 40g -0080K0·0050” 40g -0100K0·0060” 40g -0120K0·0070” 60g -0140K0·0080” 70g -0160K0·0090” 70g -0180K0·0100” 80g -0200K0·0120” 90g -0240K0·0150” 110g -0300K0·0200” 150g -0400K0·0250” 200g -0500K
Feeler Stock StripInch sizes are 12” long, 1/2” wide. Millimetresizes are furnished in 300mm lengths,12·7mm wide. Rounded ends. Each piecemarked with thickness and with convenient3/16” (5mm) hole for hanging.
Number Weight Order Codeof Blades each SEN-518
18 60g -5790K
Feeler Stock CoilAlso useful for shimming in fixture anddie work. Supplied in a compact,sturdy plastic rewindable dispenser case.Rewind feature, minimises accidentaldamage. Made of the finest tempered steel,marked every 6” or 150mm with a line,thickness in thousandths of an inch or inhundredths of a mm.
Thickness Weight Order Code(mm) each KEN-519
12.7mm x 6m
0·03 60g -3030K0·04 70g -3040K0·05 75g -3050K0·10 110g -3100K0·20 230g -3200K0·50 390g -3500K
1/2” x 25ft 0·0010” 100g -2020K0·0015” 60g -2030K0·0020” 70g -2040K0·0030” 90g -2060K0·0040” 110g -2080K0·0050” 135g -2100K0·0060” 150g -2120K0·0100” 220g -2200K0·0150” 360g -2300K
1/2” x 20ft 0·0200” 430g -2400K0·0250” 500g -2500K
FeelerGauges
Hardened and polished taper blades,enclosed in a steel case. Blades are clearlymarked for easy identification.
Metric: Manufactured to BS 957: 2008 Part 1 (Metric).Range:10 Blade:.05 - .80mm.13 and 20 Blade: .05 - 1mm.
Double Ended Feeler GaugeHardened and polished. Blade etched withsize. Manufactured to BS957: 2008 Part 1(Inch) and BS957:1969 Part 1 (Metric).Blade length: 75mm.
No.75 18 Blade:Metric range: 0.05 - 0.5mm. Inch range: 0.0015” - 0.025”.
Number Weight Order Codeof Blades (mm) KEN-518
18 60g -0790K Small Hole Gauge SetRange 3mm (1/8”) to 13mm (1/2”)The knurled handle allows fine adjustment of the gauge within the workpiece. Use in conjunction with a micrometer to accurately measure internal dimensions.
Contents: 90, 99, 110 and 110mm overall length.
Number Order Codeof Pieces KEN-518
4 -1150K
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
4PIECES
ENGINEER’S HAND TOOLS
GROUP
518
Page380
HAN
D TO
OLS
Length Impact Order Code(mm) Weight (kg) KEN-518140 1.5 - 5.0 -1750KSpare Point -1800K
Length Impact Order Code(mm) Weight (kg) KEN-518
120 2.25 - 13.5 -1710K
Heavy DutyStrength of punch and depth ofdepression is adjustable by turningthe knurled head. Delivers a punch between6.3 to 22.5kg (14 to 50lb).
Standard DutyStrength of punch and depth of depression isadjustable by turning the knurled head.Delivers a punch between 2.25 to 13.5kg(5 to 30lb).
Point Diameter Order Code(mm) KEN-518
100mm (4”) Overall Length3.2 (1/8”) -2050K4.0 (5/32”) -2060K4.8 (3/16”) -2070K6.3 (1/4”) -2090K
125mm (5”) Overall Length6.3 (1/4”) -2110K9.5 (3/8”)* -2120K
Square Head Centre PunchesNon-roll.Manufacturedfrom hardenedand temperedsteel with aknurled body forpositive grip.Precision ground60° point foraccurate markingof workpiece. Conform toBS 3066.
*Round headed.
Number Order Codeof Pieces KEN-518
4 -2100K
SetSupplied in plastic wallet.
Contents: 1x 3.2, 4, 4.8 and 6.4 x 100mm.
Automatic Centre Punches
Light DutyDelivers a punch when head is depressed. Chrome vanadium tip with rubber sheathedsteel body.
Nail PunchesCupped and bevelled precision ground pointsprovide accurate positioning over the nailhead for efficient depression. Manufacturedfrom hardenedand temperedsteel, with aknurled body forextra grip. Conform to BS3066. (Hardness:heads 42 HRC. Max:points 52 - 58HRC).
Overall length:100mm (4”).
Number Order Codeof Pieces KEN-518
4 -2300K
SetSupplied in plastic wallet.
Contents: 1.6, 2.4, 3.2 and 4mm.
Standard LengthInserted Pin PunchesManufactured from chrome vanadium steel. Used for punching out pins and dowels.
Number Order Codeof Pieces KEN-518
6 -2420K
Size Overall Order Code(mm) Length (mm) KEN-5182 115 -2412K3 125 -2413K4 150 -2414K5 165 -2415K6 180 -2416K8 200 -2418K
SetSupplied in plastic wallet.
Contents: 2, 3, 4, 5, 6 and 8mm.
Size Overall Order Code(mm) Length (mm) KEN-518
2 143 -2422K3 155 -2423K4 185 -2424K5 202 -2425K6 209 -2426K8 219 -2428K10 230 -2430K
SetSupplied in plastic wallet.
Contents: 2, 3, 4, 5, 6 and 8mm.
Extra Length Inserted Pin PunchesManufactured from chrome vanadium steel. Used for punching out pins and dowels.
Number Order Codeof Pieces KEN-518
6 -2435K
Length Impact Order Code(mm) Weight (kg) KEN-518
149 6.30 - 22.5 -1720K
Point Diameter Order Code(mm) KEN-518
1.6 (1/16”) -2220K2.4 (3/32”) -2230K3.2 (1/8”) -2250K4.0 (5/32”) -2270K
NumberContents
Weight Order Codeof Pieces each KEN-518
5 3, 4, 5, 6 & 8mm 557g -2330K
Point Diameter Overall Length Weight Order Code(mm) (mm) each KEN-5183 149 53g -2323K4 184 97g -2324K5 200 110g -2325K6 200 117g -2326K8 227 180g -2328K
Long Parallel Punch Set
Long Parallel Pin Punches with Air GripIdeal for driving tight fitting pins out of mechanical assemblies or realigning holes to fit dowel pins. Manufactured from hardened and tempered steel.
Fitted with an air grip handle that absorbs vibration as well as deflecting wayward hammer blows.
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Centre PunchesIdeal for driving tight fitting pins out of mechanical assemblies or realigning holes to fit dowelpins. Made from chrome vanadium steel with high strength octagonal shanks and featuringcushioned grip handles with shock absorbing air pockets.Overall length:150mm (6”).
Point Dia. Order Code(mm) KEN-5182.0 -2332K3.0 -2333K4.0 -2334K5.0 -2335K6.0 -2336K8.0 -2337K
Set of 6 pieces-2331Kas above
4PIECES
4PIECES
6 PIECES
6 PIECES
5 PIECES
NEW
Page381
ENGINEER’S HAND TOOLS
GROUP
518H
AN
D TO
OLS
Number Contents Weight Order Codeof Pieces (mm) each KEN-518
100mm (4”) Overall Length
6 2.4, 3.2, 4.0, 280g -2200K4.8, 5.5 & 6.4
150mm (6”) Overall Length
44.0, 4.8,
585g -2400K5.5 & 6.4
Point Diameter Overall Length Weight Order Code(mm) (mm) each KEN-518
3 210 115g -1533K4 215 160g -1534K5 225 180g -1535K6 240 195g -1536K8 270 380g -1538K10 355 520g -1540K12 355 540g -1542K
Taper Punch SetContents: 1x 3, 4, 5, and 6mm.
Taper PunchesManufactured from chrome vanadium steel. Used for aligning holes in jigs and fixtures etc.
NumberContents
Weight Order Codeof Pieces each KEN-518
4 3, 4, 5 & 6mm 683g -1550K
Parallel Pin Punches
Ideal for driving tight fitting pins out of mechanical assemblies orrealigning holes to fit dowel pins. Manufactured from hardened andtempered steel. With a knurled body for extra grip.Conform to BS 3066.
Parallel Pin Punch SetsSupplied in plastic wallet.
Point Diameter Weight Order Code(mm) each KEN-518
100mm (4”) Overall Length1.9 (5/64”) 30g -2125K2.4 (3/32”) 30g -2130K3.2 (1/8”) 30g -2150K3.4 (9/64”) 30g -2155K4.0 (5/32”) 30g -2160K4.8 (3/16”) 40g -2170K5.5 (7/32”) 30g -2180K6.3 (1/4”) 40g -2190K
130mm (5”) Overall Length7.8 (5/16”) 150g -2192K8.8 (11/32”) 175g -2196K
150mm (6”) Overall Length4.0 (5/32”) 60g -2350K4.8 (3/16”) 70g -2360K5.5 (7/32”) 175g -2370K6.3 (1/4”) 280g -2380K
Straight Shank Hollow PunchesManufactured from hardened carbon steel. Through body ejection of the punched material makes them ideal for punching clean edged holes in leather, wood, plastics, card and paper.
Cut Diameter Overall Order Code(mm) Length KEN-518
5 (3/16”) 100mm -1580K6 (1/4”) 100mm -1581K8 (5/16”) 105mm -1582K10 (3/8”) 117mm -1583K11 (7/16”) 117mm -1584K12 (1/2”) 115mm -1585K14 (9/16”) 115mm -1586K16 (5/8”) 115mm -1587K17 (11/16”) 115mm -1588K19 (3/4”) 118mm -1589K21 (13/16”) 118mm -1590K22 (7/8”) 118mm -1591K24 (15/16”) 121mm -1592K25 (1”) 121mm -1593K
Hollow Punch SetsSupplied in hardwearing PVCpocket wallets with tie fastening.
Cut Diameter Overall Order Code(mm) Length KEN-518
29 (11/8”) 175mm -1594K32 (11/4”) 175mm -1595K35 (13/8”) 205mm -1596K38 (11/2”) 205mm -1597K44 (13/4”) 210mm -1598K51 (2”) 210mm -1599K
Reduced Shank Wad PunchesFor a variety of soft materials. Can be used for cutting holes andproducing clean edged discs from the material being cut.
NumberContents
Order Codeof Pieces KEN-518
5mm (3/16”)6mm (1/4”)
68mm (5/16”)
-1600K10mm (3/8”)11mm (7/16”)12mm (1/2”)6mm (1/4”)8mm (5/16”)
610mm (3/8”)
-1650K12mm (1/2”)16mm (5/8”)19mm (3/4”)
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
6PIECES
4PIECES
Page382
HAND TOOLS
ENGINEER’S HAND TOOLS
GROUP
518
Weight Order CodeDescriptioneach KEN-567
Spare bulb -6400K
Mirror Weight Order CodeDiameter each KEN-518
50 x 25mm 220g -5500K
Inspection MirrorsWith flexible shafts which can be adjusted into any position. Available as standard or with light attachment. Both models have high gradedistortion-free glass mirrors with chrome plated shafts. Inspection mirror with light requires 2x ‘AA’ batteries and has a swivel head.
Standard
With Light AttachmentFlexible shafts which can be adjusted into any position.
Telescopic Shaft Inspection Mirrors
Ball and socket universally positional joint, holds the high grade distortion free mirror at any angle. Chrome plated high polish finish telescopic shafts.
Circular Mirror
*With high power magnet and pocket clip.
Mirror Length Weight Order CodeDiameter Closed/Open each KEN-518
30mm* 180/480mm 41g -5380K
Rectangular Mirror
Eye LoupesManufactured fromshock resistant plastic.Shatterproof lens. Ideal for jewellers,watchmakers,electronics and modelmakers.
Magnification Focal Length Weight Order CodeFactor (mm) each KEN-518
10.0x 31 (11/4”) 20g -6000K
Magnification Focal Length Weight Order CodeFactor (mm) each KEN-51810.0x 31 (11/4”) 20g -5290K4.0x 63 (21/2”) 14g -5300K3.5x 75 (3”) 10g -5310K3.0x 90 (31/2”) 10g -5320K
Diameter MagnificationOrder CodeKEN-518
50mm 5x -6040K75mm 4x -6060K100mm 2x -6080K
Clear
Spare Bulb
Solid
Mirror Length Weight Order CodeDiameter Closed/Open each KEN-518
50mm 280/420mm 100g -5420K
Hand MagnifiersPlastic lightweight magnifiers. Used to provide a clear crispenlarged image.Used for inspectionof finished parts,enlarging small textand pictures etc.
Size Order CodeKEN-518
100mm x 100mm -5360K
Inspection MirrorSheet glass mirror recessedinto lightweight aluminiumhousing. Gives clear visibilityin concealed areas.
Size: 100 x 100mm.
100mmSQUARE
UP TO100mmDIAMETER
Mirror Length Weight Order CodeDiameter Closed/Open each KEN-518
90 x 50mm 370/550mm 127g -5460K
Mirror Weight Order CodeDiameter each KEN-518
50mm 180g -5400K
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Page383
ENGINEER’S HAND TOOLS
GROUP
518H
AN
D TO
OLS
Die Stock Set Contents:1 - 13/16” x 150mm,1 - 1” x 210mm,1 - 15/16” x 280mm.
Outside Order CodeDiameter KEN-518
13/16” -8070K1” -8100K
15/16” -8130K11/2” -8150K2” -8200K
Die StocksAll steel drop forged solid construction forlong life with knurled handles for extra grip.Designed to hold a range of different sizes ofround split-adjustable dies. The three screwdesign easily locks die into position andmaintains alignment for accurate threadingresulting in clean, straight threads.
Tap Wrench Set Contents:Square size: 2.8 - 5mm and4.0 - 12mm.
Tap Wrench & Diestock SetContentsDiestocks: 1” x 13/16”,1” x 1”, 1” x 15/16”. Tap wrenches (square size): 1 x 2.8 - 5.0mm and 1 x 4.0 - 10.0mm.
Square Size Order Code(mm) KEN-518
2.8 - 5.0 -8320K4.0 - 10.0 -8350K4.0 - 12.0 -8390K5.3 - 17.0 -8470K
Square Size Order Code(mm) KEN-518
1.5 - 5.0 -8800K2.0 - 7.2 -8820K2.5 - 9.0 -8840K
Bar Type Tap WrenchesDuctile steel body with a knurled locking nutensuring no loss of grip during use.
Engineer’s Tap WrenchesWith all steel, hardened and temperedbodies, solid construction, hardened groundjaws and knurled adjustable handles for extragrip. Straight handle design provides greaterleverage, especially when using largerdiameter taps.Tap sizes to ISO 529.
Number Order Codeof Pieces KEN-518
3 -8210K
Number Order Codeof Pieces KEN-518
5 -8500K
Number Order Codeof Pieces KEN-518
2 -8480K
Chuck Style Tap Wrenches
English TypeUsed in hand tapping operations, theyprovide the reach and leverage needed foraccurate tapping in tight spaces. Heavy dutyductile steel body with knurled chuck, fourequalising jaws to hold the tap true andsliding T-bar which can be used when tappingagainst a shoulder or other obstructions. Individually boxed.
Square Length Order CodeSize (mm) (mm) KEN-518
Slimline2.0 - 4.0 55 -8520K
Standard Length4.0 - 5.0 60 -8550K4.0 - 5.5 70 -8580K
Long Reach3.0 - 3.9 100 -8620K5.6 - 6.2 120 -8690K
Square Length Order CodeSize (mm) (mm) KEN-518
Standard Length2.0 - 2.8 50 -8860K3.0 - 5.0 65 -8880K7.0 - 9.4 90 -8900K
Long Reach3.0 - 5.0 165 -8920K7.2 - 9.0 255 -8940K
Chuck Type Tap Wrench SetEnglish TypeContents: Standard length2.0 - 2.8, 3.0 - 5.0, 7.0 - 9.4mm.
Extra length3.0 - 5.0, 7.2 - 9.0mm.
Replacement Jaws
Square Length Order CodeSize (mm) (mm) KEN-5183.0 - 6.0 85 -8720K6.0 - 8.0 100 -8750K
To Suit Order CodeKEN-567
KEN-518-8720K -6500KKEN-518-8750K -6510K
Ratchet Type Tap Wrenches Manufactured from hardened and temperedsteel, with chrome plated high polish finish. Switchable between forward and reversecoupled with the multi-positional sliding T-barmakes this tap wrench ideal for use inconfined spaces. Individually boxed.
Japanese TypeUsed in hand tapping operations, theyprovide the reach and leverage needed foraccurate tapping. Heavy duty ductile steelbody with knurled chuck, stepped chuck jawsand four point clamping increase the range oftap sizes which can be used in the wrenchfitted with a fixed T-bar. Individually boxed.
Number Weight Order Codeof Pieces each KEN-518
5 895g -9000K
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
2PIECES
5PIECES
3PIECES
5PIECES
ENGINEER’S HAND TOOLSGROUP
518
Page384
HAN
D T
OO
LS
Group 330
DescriptionWeight Order Codeeach KEN-518
Pocket Type with Clip 46g -4330KScriber Point KEN-567-6200K
DescriptionWeight Order Codeeach KEN-518
Machinists Standard 36g -4350K
DescriptionWeight Order Codeeach KEN-518
Double Ended 60g -4370K
DescriptionWeight Order Codeeach KEN-518
Chisel Point & Scraper 34g -4360K
MachinistsOne piece single ended for marking out in confined places.
Overall length: 115mm.
Chisel Point & ScraperMachinists scriber with scraper. Double ended. Ideal for cleaningsurfaces prior to marking out. With chisel point.
Overall length: 180mm.
Double Ended Double ended, ideal for marking out in hard to get places eg. grooves.
Overall length: 180mm.
ScribersUsed for the marking out of fine lines on metals. Manufactured from hardened and tempered high grade steel with knurled bodies for high grip and precision ground points foraccurate marking. Available with a chisel point, pocket type,machinist’s standard type, double ended, which are mainly used inconjunction with surface gauges.
PocketWith steel tip only, also a reversible point to prevent snagging ofclothing when clipped into pocket. With knurled bodies for extra grip.
Overall length: 88mm.
Etching Pen ScriberFor marking, scoring and identification on hard and soft materialsincluding alloy, copper, stainless steel, glass and ceramics.
Overall length: 180mm.
Retractable Carbide Tipped Etching PenFor marking and scribing in hard and soft materials including steel,ceramics, plastics and timber.
Overall length: 180mm.
Flexible Pick Up ToolFour prong steel retractable claw. Flexible steel stem with a springloaded plunger to open and close jaws. Chrome plated and corrosion-resistant. Ideal for recovery of small objects.
DescriptionWeight Order Codeeach KEN-518
T.C.T. For Glass/Tiles 35g -4200KSpare Tip for Etching Pen 9g -4240K
DescriptionWeight Order Codeeach KEN-518
Retractable Etching Pen 35g -4220KSpare Tip for Etching Pen 9g -4240K
Length Order CodeKEN-518
600mm (24”) -4820K900mm (36”) -4840K
Pillar Weight Order CodeHeight (mm) each KEN-518
230 & 305 1.50kg -4300K
Surface Gauges
Used for marking out linesparallel to a true edge orgroove, and also to mark thecentre of round bars. Machined base, two pillars, adouble ended scriber and anadjustable attachment forholding scribers up to 1/4”diameter on to the pillar. The base has a machined V-groove for use on pipes andround bar and two frictionallyheld pins which are used as aguide when sliding along thetrue edge or groove. The angle of the pillar can befinely adjusted with the use of aknurled thumb screw. Supplied with two pillars.
Base dimensions:78 x 58mm.
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
Page385
ENGINEER’S HAND TOOLS
GROUP
518H
AN
D TO
OLS
FlatFor use on flat surfaces and external cylindrical surfaces.
3 Piece Set1 each 100mm three square, half round and 205mm flat.
Number Weight Order Codeof Pieces each KEN-518
3 350g -2850K
Length Width Weight Order Code(mm) (mm) per 5 KEN-518
100 11 330g -2540K150 16 600g -2560K205 16 1000g -2580K
Engineer’sScrapers
Wooden contoured handles with high grade steel blades, hardened and tempered with extremely keen cutting edges. Scrapers reduce high spots from a surface which has been previously machined or filed.
Length Width Weight Order Code(mm) (mm) per 5 KEN-518
100 8 320g -2440K150 10 620g -2460K205 15 1200g -2480K
Length Width Weight Order Code(mm) (mm) per 5 KEN-518
100 16 360g -2640K150 19 650g -2660K205 23 1300g -2680K
Half Round For use on hollow surfaces such as bearing linings and internalcylindrical surfaces.
Three SquareSuitable for tool room and light engineering work. Used on small bearings and bushes and into restricted/tight angles.
Toolmaker’s ClampsHardened and tempered jaws with spring tension clips.
Length Order CodeCapacity(mm) KEN-518
32mm 50 -4400K58mm 75 -4410K70mm 100 -4420K89mm 125 -4430K
Capacity Length Order Code(mm) (mm) KEN-518
0.0 - 1.00 83 -1210K0.8 - 1.50 85 -1220K1.3 - 3.10 90 -1230K3.0 - 4.80 100 -1240K4 Piece Set - Capacity 0.0 - 4.80 -1200K
Pin ChucksFor holding small drills in lathes and larger chucks. With three collets.
Range Order Code(mm) KEN-518
0.25 - 2.5 -1260K
Number Order Codeof Pieces KEN-518
4 -2900K
Miniature Hook & Pick SetIncludes straight pick, full hook, 90° hook and 45° hook. Ideal for use on cotter pins, keys, ‘O’ rings, springs and washers. Hardened and tempered chrome vanadium steel shanks with aknurled section for precise grip. Impact resistant square sectionhandles for secure grip even when greasy.
Overall length: 120 - 130mm (43/4” - 51/8”).
Pin VicesManufactured from hardened steel. Ideal for holding drills, small filesand wire. The through hole construction of the body allows lengths ofwire to be held.
Number Order Codeof Pieces KEN-518
7 -2920K
Universal Hook & Pick SetDesigned for use in automotive and engineering applications. Idealfor use in the removal of O-rings, cotter pins, seals, bushes, springsand washers. Impact resistant handles. Presented in sturdy blow moulded plastic case.
Contents; 210mm (8”) hook tip, straight tip, 90° tip 135mm (5”),straight tip, hook tip,combination tip,90° tip.
PRODUCTS ARE ONLY AVAILABLE VIA YOUR DISTRIBUTOR © 2016
3PIECES
4PIECES
7PIECES