(government of india undertaking) notice inviting … · gn,sector-v,saltlakecity,kolkata: ......
TRANSCRIPT
1
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.a) The Tenderer shall furnish copies of :
i) IT Registration Certificate with No.
ii) Sales Tax Registration Certificate with No.
iii) Service Tax Registration Certificate with No.
iv) Electrical Contractor's License with No.
v) Electrical Supervisor’s License with No.
5.
a)
b)
c)
d)
e)
1.
2.
(Government of India Undertaking)
NOTICE INVITING TENDER
Interested agencies having experience in work of similar nature & magnitude and fulfilling the eligibility criteria given
below may download detailed tender document from Bank's Website http:bankofbaroda.com/tenders.asp
marked Annexure - IV
The tenderer should have completed in last three Financial years (i.e. current year & two previous financial year) in
Bank, Govt. or Govt. undertaking and Financial Institutions, Corporate Sectors, etc. minimum 3 (three) similar
composite work (Interior Furnishing & Electrical) costing not less than Rs. 15.00 lacs in single contract. (Work order &
completion Report in support must be submitted & marked as Annexure-I)
The total contract amount received by the Tenderer during the last 3 financial years should be minimum as 40.00 lacs
per year in contract work. In support of this the Tenderer should submit audited sheet duly Certified by the Chartered
Accountant & marked Annexure-II.
The Tenderer should produce Solvency Certificate from any Nationalised / Scheduled Bank for an amount of 200% of
the advertised Tender value marked Annexure-III.
Part 'A' envelope (Technical Bid) shall contain : Earnest Money, the documents for satisfying eligibility criteria & the
technical & financial stipulation, if any, of the tenderer & Part 'B' shall contain : financial bid along with a copy of the
tender document, duly signed in all pages both shall be separately sealed & submitted in another sealed envelope
to the Asst. General Manager, Bank of Baroda, West Bengal, Sikkim & A & N Island, BARODA TOWER, Plot No. 38/2, Block
GN, Sector-V, Salt Lake City, Kolkata : 700 091, before 2.30 P.M. on 18.07.2012 along with Earnest money amounting to
Rs.11,000/- by Bank Draft / Pay order in favour of Bank of Baroda shall be submitted in Part 'A'.
MINIMUM ELIGIBILITY CRITERIA (Shall be submitted with Part A of the Offer)
Part 'A' will be opened at 3.30 p.m. on 18.07.2012.
Bank of Baroda, West Bengal, Sikkim & A & N Island invites sealed tenders in two bid system for the proposed
Civil,interior & electrical work of Purulia Branch,Court Road,PO & Dist Purulia, West Bengal-723101. The work is to be
completed within 21 Days.
List of important plant & machinery available on hand (own) and proposed to be inducted (own & hired to be given
separately) for carpentry & electrical work (marked Annexure-X)
List of works completed in the last (three) financial years under Bank / Govt., Semi - Govt,Govt. undertaking /
Corporate Sectors giving description of work, organisation for whom executed, approximate value of contract at the
time of award, date of award and date of scheduled completion of work, date of actual completion and final value
of contract should also be given (marked Annexure-XI)
marked Annexure - V
List of works in hand indicating description of work, contract value, approximate value of balance work yet to be
done and date of award (marked Annexure-XII)
Contractors will be required to arrange for their own storing. Dismantled materials are to be carted away from site at
their own cost and disposed of in conformity with Municipal regulations.
Tenderer who will quote the rate must have a local office at Kolkata. This is absolutely essential for day to day
supervision & coordination of the work at site.
All informations are to be fully authenticated & documented failing which the documents submitted will not be accepted.
GENERAL TERMS & CONDITIONS
The tenderer are to visit the site and acquaint themselves with site conditions before quoting rates.
Part 'B' of the tenders will be opened for those only who fulfils the qualifying criteria given in the tender document.
The unopened part 'B' along with Earnest Money deposit for those not fulfilling qualifying criteria will be returned.
Clarifications, if any, required on drawings, schedules, specifications, etc. can be obtained from our Consultant M/s.
D.Subhas & Associates 7A,Akrur Dutta Lane,Gr Floor,Kolkata 700 012 Phone No -033 2237 9520,9874530792,9830553457
The Tenderer should also submit the following documents along with the Tender.
List of technical persons available on hand, years of their association with the firm & proposed to be engaged for the
subject work, if selected (marked Annexure-IX) ;
The bank will not be bound to accept the lowest tender and reserves the right to accept or reject any or all tenders
without assgming any reason whatsoever.
marked Annexure - VI
marked Annexure - VII
marked Annexure - VIII
1
3.
4.
5.
6.
7
8.
9.
10.
11.
Payments will be made once on completion by the Employer within 15 days after certification of bill by the
Consultant 10% of the total payable amount is to be retained as retention money and will become due for release
after expiry of six months from the date of completion of the installation & subject to satisfactory maintenance of the
executed work.
Tenders addressed to Asst. General Manager, Bank of Baroda, West Bengal & Sikkim Region and submitted at his
office at BARODA TOWER, Plot No. 38/2, Block GN, Sector-V, Salt lake City, Kolkata : 700 091, before 2.30 P.M. on
18.07.2012, accompanied by Earnest Money amounting to Rs. 11,000/- by Bank draft payable to Bank of Baroda
and other documents as mentioned in NIT. Part 'A' of the tenders will be opened at 3.30 P.M. on the same date.Part
'B' will be opened immediately after opening of Part 'A'.
The bank will not be bound to accept the lowest tender and reserves the right to accept or reject any or all tenders
without assgming any reason whatsoever.
The arrangement for “ Wire Management " is to have prior approval of the Client.
The quoted rates shall remain firm during the entire currency of contract. No price variation for any causes
whatsoever, shall be entertained.
The time of completion shall be 21 days from the date of placement of order.
The offer shall remain valid for acceptance for a period of 30 days from the date of submission of offer.
The quoted rates, are to include cost of all materials, labour and or any other material, all statutory taxes, transport,
handling delivery at site and installation, complete in all respect, as per drawing, directions or instructions of
Employer/Consultant. The quoted rates are also to include dismantling of partitions, counters, old electrical wirings
etc. and stacking serviceable materials and disposal of debris, etc.
Prior approval of the Employer/ Consultant shall be obtained for colour and thickness of laminates to be used in the
work.
2
SPECIFICATION OF MATERIALS FOR INTERIOR WORK
Sl.No. Description
1. Laminate
2. Ply & Block Board
3. Glass
4. False Ceiling & Accessories
5. Veneer
6.Textured Wall Paint
7. Glue
8. Locks
9. Aluminium Hardware Fittings
10. Brass Hardware
11.
Floor Spring
12. Screws
13. Casters
14. Sliding Drawers / Channels
15. Furnishing Fabric
16. Leather Foam
17. PVC Flooring
18. Carpet
Efficient Gadjets
Evrite Agencies Pvt. Ltd. / Nita Floor Spring
Nettle Fold
ICI, Spectrum, Heritage
Godrej / Secur / Yale
Brass Arts / Vijoy
Glamour or Favourite (Balla Industries)
Woven type "Harmony" range from "Vimal"
or equivalent
Bhor Industries or equivalent
Armstrong / Krishna / Premier
Durian / Century / Archid
ICI, Jenson & Nicholson / Asian paint /
Berger
Make (s)
Metako / Allen / Crown with ISI Mark
India Gypsum Ltd.
Marino / Greenlam / Century / Archid
Green / Century / Archid / Austin
Modi / Indo Ashahi / Float Glass India Ltd.
Earl Behari / Efficient Gadjets
3
SPECIFICATIONS OF MATERIALS FOR ELECTRICAL WORK
Sl.No. Description
1. Switch fuse / fuse switch units (HRC) (32A TPN & above)
2. Timer (TSQ 100)
3. Voltmeter & Ammeter
4. Voltmeter & Ammeter selector switches
5. Phase indicating lamp
6.
7. Capacitor
8. HRC fuses
9. Power Cable : XLPE
10.
11. HRC fuse base & carriers.
12. PVC terminals
13. 1.1 KV grade PVC insulated armoured aluminium cable (ISI marked)
14. 1.1KV 660V grade PVC insulated & sheathed / insulated copper wire &
flexible cords (ISI marked).
15. Moulded case circuit breaker
16. RCCB / ELCB
17. Switch fuse with rewirable fuses. (6A & 32A TPN)
18. Isolator
19. Changeover switch (on load type)
20. MCB distribution board
21. Distribution fuse board with rewireable fuses
22. Miniature circuit breaker / MCB type isolator
23. Contractors
24. Auxiliary contractor
25. 1/16 Amp Piano key type switch / flushed type plug socket
26. 6/16 Amp modular switch / socket, module plate & mounting M.S. /
PVC box.
27. 300W, 2 module electronic regulator
KENBAR / HAVELLL’S / ELCON / HPL /
CONTROL & SWITCHGEAR.
LEGRAND/ SIEMENS
A E / KAPPA SEGC & CONTROLS / CONTROL
CROMPTON/SIEMENS
TATA LEVERT/NEUMERIC/ KIRLOSKAR
GLOSTER/INCAB/POLYCAB/CINOLEX
GE power / SIEMENS / L & T / SCHNEIDER
SWITCHGEAR
GE Power/SIEMENS/L&T/SCHNEIDEV
HAVELL’S / BPC / BOSMA
UNIVERSAL / GLOSTER / NATIONAL / NICCO
/
L & T / SCHNEIDER/LEGRAND
CPL (Genius) / ANCHOR (Roma) / CRABTREE
/
MK
ANCHOR (Roma) / CRABTREE / MK
ANCHOR / PRECISION / SSK & RIDER
HAVELL’S / STANDARD
NATIONAL/FINOLEX/ HAVELLS
LEGRAND / SIEMENS
SIEMENS / L & T/BCH
SIEMENS / L & T
KAYCEE / L & T
LEGRAND/ SIEMENS / L&T
Make (s)
HAVELL’S / STANDARD
Vaishno / SIEMENS / ROSS controls
L & T
GE power / SIEMENS / L&T / Schneider
A. E. / IMP
ELMEX / ESSEN
4
Sl.No. Description
28. Ceiling rose
29. Holder
31. Luminous indicating type buzzer with cancellation push.
32. Alarm bell.
33. G.I. pipe
34. Steel conduits (conforming to IS in all respects)
35. Black enamelled
36. Galvanised
37. Non-metallic PVC conduit pipe
38. Compression type brass gland
39. Cable termination socket
40. Light fitting & lamps
41. Decorative/Ornamental /Chandelier / Light Fittings
42. Ceiling Fan
43. Exhaust fan
44. Industrial type socket & top
45. Telephone wire
46. Telephone Socket
47. Network Cable
48. Contractors
49. STARTERS
FINOLEX or equivalent
L & T / SIEMENS
CROMPTON / POLAR / KHAITAN
NORTH WEST / CABTREE
CROMPTON / POLAR / KHAITAN
HAVELL’S / CROMPTON / LEGRAND
FINOLEX / RRK/NATIONAL
CRABTREE/MK
CROMPTON / POLAR / KHAITAN / EPC
DOWELL'S
WIPRO or equivalent
DOWELLS / JOHNSON / COMET
PLAZA / KALINGA/ PRECISION/AKG or
equivalent
KHERAJ / GETCO
KAY / EPP / ANCHOR / JJ
NATIONAL / HOMA / EQUIVALENT
Good local make with minimum wall
thickness of 3 mm. for 19 / 20 mm. and 25mm
sizes & 2.5 mm. for 12mm. sizes
BEC / SUPREME / AKG
BEC / SUPREME / AKG
BST / BANSAL
KAY / EPP / ANCHOR / JJ
Make (s)
5
Sl No. Unit QTY Rate (Rs.) Amount (Rs.)
1.0 PARTITION
Providing and fixing partition consisting of 2 1/2” x 2 “
finished sal wood section without sap and joints at maximum
2'-0”c/c both horizontally and vertically treated with
pentapehene pale from STP as anti termite & fare retardant
from viper.to be fixed screwed to the floor and celing with
M.S cleats. The frame work will be claded with 8.00 mm thk.
HDFR SHEET both sides and finished with 1.0mm thk.
Approved shade laminate as per design with approved
adhesive 3”x1/2” white beach / white ceader skirting with
natural polish to be fixed along with the entire bottom length
of partition on both sides. Extra frame work to be fixed for
fixing glass. In case of low ht. Etched/frosted glass with
sand blasting/granular blasting to be provided fixed with
3”x3/4” white beach/ white ceader moulding with natural
polished all complete in case of low ht. Partly glazed
partition ( 6'-0” ht. ) the front portion should have 12mm
machine polished glass to be provided as per
specification/drawings.
(a) PARTLY GLAZED PARTITION
i) Full Ht. Partly Glazed partition upto FC HT ie 8FT SFT 90.0
ii) Low Ht. Partly Glazed partition upto 4'-0” & 6'-0” SFT 155.0
(b) BLOCKED PARTITION
(I) Full Ht. SOLID partition upto FC HT ie 8FT SFT 190.0
2 Door and Accessories
For the door 35mm solid core flush door with necessary hold
fast fixed to the wall/ partition with 1.0mm laminate
(approved shade) 3”x3/4” white beach/white ceader cover
moulding with natural polish to be provided along the door
opening necessary rabit to be provided. In case of partly
glazed door 8mm thk. etched/frosted glass of approved
make to be provided in case of vision panel door 18”x9”
8mm thk.clear glass to be provided. The work to be
completed as per specification design and approval of the
Architects.Supplying and fixing door accessories as door closure, door
stoper, Floor spring (heavy duty). Brass hinges, locks and
handle etc. The work to be completed as per specification
and approval the Architect.
(a) PARTLY GLAZED DOOR
Full ht. Partly Glazed (7'-0” x3'-0”) WITH DOOR
FRAME ( AS NEEDED)
Nos 4.0
(b) ii FULL HT BLOCKED DOOR (7'-0”X 2'-6”) WITH DOOR
FRAME ( AS NEEDED)
NO 3.0
(b) iv FULL HT GLAZED DOOR (7'-0”X 3'-8”) WITH DOOR
FRAME ( AS NEEDED) BM CHAMBER
NO 1.0
c) MAIN ENTRANCE DOOR (4' x 7')
PROJECT – BANK OF BARODA, PURULIA BRANCH
B O Q AND ESTIMATE DETAILS CIVIL& INTERIOR WORKS
Providing and fixing fully glazed pivoted door at the main
entarance consists of 6”x2” seasoned hard wood section
covering with white beach/ white ceader beading for bottom
rail and and 4”x2” seasoned hard wood section covering with
white beach/ white ceader beading for top rail finished with
natural polish. 12 mm thk Modi Gaurd/ Saint Gobain clear
float glass with sand blasting/etching (as per design) and SS
finish handle (1'-0” long) of Neki/Hasseley make to be fixed
on both sides & proper arrangement in bottom rail to be
done. The rate should include lipping, moulding, beading, &
heavy duty floorspring. The work to be completed in all
respect as per design, direction and approval of the
architect. The doors will have Bank's logo.
Nos 1.0
7.0 STORAGE
Providing and fixing storage made out of 18mm HDFR
BOARD for top,sides & 8mm HDFR for back finished with
1.0mm laminate. The shutters to be made out of 18mm
HDFR board with 1.0mm laminate. The necessary godrej
multipurpose locks 6” SS matt finished handles, auto closing
hinges src to be provided. 3”x 1/2” white beach/ white
ceader wooden skirting to be provided duly natural polished
as per matching tone. Inside of the unit to be synthetic
enamel painted in matching tone. All the exposed edges of
the boards/ plywoods to be covered withwhite beach/ white
ceader wooden lippings 1 1/2” x1' mouldings duly natiral
polished all complete. For full ht storage file divider made
out of 6mm thk ply to be provided. The work to be
completed as per approval and specification of the architect.
i)Low Height Storage (ht upto 2'6”) SFT 178.0
8.0 WRITING LEDGE
Providing & fixing writing ledge as per design made out of
19mm block board with necessary groove patterns 1.0mm
laminate to be cladded 18mm thk telephone black granite
with bull nosed moulding (double) at facia to be provided on
top of the writing ledge. A divider made of 19mm block
board to be provided. White beach/white ceader lipping with
natural polish to be used in all exposed areas, inside of
writing ledge to be enamel painted. The work to be
completed as per design and approval of the architect
NO 1.00
9.0 VERTICAL BLINDS
Providing and fixing vertical blinds of 100mm thk
(Mac/Annums/) of approved shade and pattern having
handail made of high strength alluminium alloyed wll
thickness of 1.2 mm thk handrail to have 25mm decorative
insert. Control unit shall be ofderlin. The runners are also to
be a derlin withantiflixtion adeshive. Spacers should be made
of stainless steel. Febric should be polyester
viscosted/polyester yarn having protective coating with
chemicals for stain resistance & soilrepalancy. The rate shall
include necessary scoch gurd treatment on both sides. The
overlaping should be uniform and adequate. Necessary
operative arrangements frames to be provided. The work to
be completed asper specification and approval of the
architect.
SFT 90.0
10.0 SOFT BOARD/ NOTICE BOARD
Providing and fixing soft board/ notice board fabricated out
of 12mm BWR ply covered with 12mm soft board padding
and upholsply propylene fabric @80/ mtr. Edges of the soft
board should have white beach/white ceader moulding with
natural polished.
SFT 15.0
NOTE:- where pin up board is in a panelled area, the top of
the pin up board should be flushed with the panel, kepping
the same level. The work should be completed as per design
specification & approval of the architect.
11.0 ROLLING SHUTTER ENCASEMENT
Providing & fixing rolling shutters encasement fabricated out
of 12 mm thk HDFR board finished with 1.0mm thk laminate
for top sides,front and bottom with necessary opanable
pallah at bottom,hardware including locks, hinges & handles.
The job to be completed as per approval of architect.
SFT 9.0
12.0 MAIN PANEL ENCASEMENT
Providing & fixing rolling shutters encasement fabricated out
of 12 mm thk HDFR board finished with 1.0mm thk laminate
for top sides,front. Encasement will be having louver & 6mm
thk glass for seeing the indicatorin both pallahs. The
exposed surface of 12 mm thk HDFR board will be finished
withwhite beach / white ceader lipping & inside to be enamel
painted. The job to be completed as per approval of
architect.
SFT 45.0
13.0 PILLAR CLADDING
Providing & fixing in position columncladding consisting of
8.0 mm HDFR boards, 1.0mm thk laminate with hardwood
ribbing of 1 1/2” x 1” dimension. The of the column is to be
texture/heritage painted. texture/Heritage paint area as
shown in drawings. The item is to be completed in all
respects as per design & approval of the architect.
SFT 155.0
14.0 SYNTHETIC DOOR MAT
Providing fixing synthetic door mats of approved shade from
Birla 3M (6mm thk). The work to be completed as per
approval of the Architect.
Nos 1.0
15.0 PLY BLOCKING WITH PAINT FINISH SFT 40.0
Providing & fixing in position ply blocking consisting of 8.0
mm HDFR boards, paint finish as per apporved shade. The
item is to be completed in all respects as per design &
approval of the architect
16.0 FALSE CEILING (anutone board)
Providing and fixing HDFR MAGNESIA BOARD ( TUFBLOC /
ANUTONE MAKE / EQUIV ) board false ceiling which includes
G.I perimeter channels of size 0.55mm thk. (having one
flange of 20mm and another flange of 30mm and a web of
27mm) along with perimeter of ceiling screw fixed to brick
wall/partition with the help of nylon sleeves and screws, at
610mm centers Then suspending G.I intermediate channels
of size 45mm (0.9mm thk. With two flanges of 15mm each)
from the sofit at 1220mm centers with ceiling range of
width 25mm x10mmx0.55mm thk fixed to sofit with G.i cleat
and steel expansion fasteners celling section of 0.55 mm thk
having knurled web of 51.5mm and two flanges of 26mm
each with lips of 10.5 mm are then fixed to the intermediate
channel with thev help of connecting clip and in direction
perpendicular to the intermediated channel at 457mm
centers 12mm tapered edge TUFBLOC is then screw fixed to
ceiling section with 25mm drywall screws at 230mm centers
screw fixing is to be done mechanically either with screw
driver or drilling machine with suitable attachment.
Edges of the boards with jointing compound No extra
payment will be made for the cutting of light points stain
glass cove lighting etc. The measurement will be taken in
one level rate should include the drops also. No extra
amount will be paid for the crops the joints to be properly
mended with paper tapes and gypsum compound two coats
of drywall top coat all complete. The rate should include the
full completion of the ceiling at the time of handing over the
site all necessary repairing work to be considered if required.
No Drop or design (if any) will be considered as extra
measurement it will be considered flat ceiling.
SFT 1790.0
17.0 ACRYLIC EMULSION PAINT
Providing and applying Acrylic emulsion paints after
removing the damaged plaster re plastering with 12mm thk
cement mortar after finishing with p.o.p to make the
necessary smoothness preparing all damages. Then two
coats of primer of approved make to be applied finished with
two or more coats of acrylic emulsion paints. The work to be
completed as per approval and satisfaction of the Architect.
SFT 2100.0
18.0 CORNICE MOULDING
Providing and fixing pop cornice moulding along the periferi
wherever the walls/ partition meeting the ceiling size 3” x 1
1/2” duly painted as per approval of the Architect.
RFT 410.0
19.0 WALL PREPARATION
a Cement Plaster
Providing internal cement plaster, 12mm thick in a single coat
of 1:4 cement mortar to concrete and masonry surfaces in all
positions including of hacking of RCC surfaces, all plaster works will
have provision of chicken mesh of 12mm x 12mm x 20 gauge in
SFT 100.00
b POP Punning
Punning with 8mm to 19mm thick layer of super fine plaster of
paris (anhydrous gypsum) applied over selected existing plastered
surface on walls and columns finished smooth, surface prepared by
hacking and applying a coat of cement slurry if required inc
SFT 100.00
20.0 SANITARY ITEM – IVORY
A Providing and fixing white vitreous china pedestal type
water closet (European Type) of approx size 455 x 360 mm
with heavy type solid seatand lid of matching shade with C.P
. Brass hinges, rubber buffers including cutting and making
good the floors, wherever required and connecting to the
existing pipe line as directed.
Nos 2.0
B Providing and fixing white rigid P.V.C. 8 litres low levels
flushing cistern with internal fittings and supporting
brackets, 20 mm dia overflow pipe with specials of standard
make and mosquito proof couping of approved design
including cutting and making good the walls wherever
requird.
Nos 2.0
C Providing and fixing white vitreous china ware flat back half
stall type Urinal of approved make of size 630mm x
420mm x 390mm with C.P.waste pipe with on end expanded
and coupling nut etc. complete.
Nos 3.0
D Half round channel of various types such as plain piece,
stop end stop end with outlet , according to requirement of
site. Set in cement concrete (1:3:5) with stone aggregate
channel will be of 600 mm x 150 mm size in white vitreous
ware jointed with white cement complete as per direction.
Nos 3.0
E Providing and fixing white vitreous china flat back wash
basin of 550 mm x 400mm size with a single 15mm CP brass
piller cock with CI/M.S bracket, 15 mm Cp brass stop cock.
15mm dia. PVC connector with end coupling, 32mm dia semi-
regid PVC waste pipe of standard pattern, including painting
of fittings and brackets, cutting and making good the walls
wherever the required.
Nos 4.0
F Providing and fixing in position 18 mm thick mirror
polished granite slab of approved shade and quality to
wash basin counter including forming opening in the
Granite slab to recive circular wash basin and pipes as
required, fixed in brick wall supports, machine cut and
polished on exposed surface s and edges (brick supporting
wall will be paid under separate item).
SFT 15.0
Size of Granite slab; 1500 mm x 600 mm approx. in single
piece of each.Payment will be made in overall area of Granite slab.
G Providing & fixing liquid soap container of standard size
made of chromium plated desity plastic of approved design
and quality.
Nos 3.0
H Providing and fixing towel rail of approved make and
quality complete with brackets fixed to wooden cleats with
C.P. brass counter sunk screws 600mm long x 25mm dia.
Nos 3.0
I Prviding and fixing C.P brass robe of approved make and
design.
Nos 2.0
J Providing and fixing in position white vitreous china
recessedtype toilet paper holder of approved make and
design, fixed on the masonry surface, mending good
damages, all complete as directd.
Nos 2.0
K Providing and fixing mirror 6mm thick of superior glass (0f
approved quality) complete with 6mm thick asbestos sheet
ground fixed to wooden cleats with C.P. brass counter sunk
screws and washers and C.P. clips including providing Tesk
wood moulding of 50mm x 25mm size duly polished all
round the mirror.
SFT 15.0
L Providing and fixing 15mm nominal bore C.P. brass bib
cock of standard design and of approved make conforming
to I.S. : 8931.
Nos 6.0
M Providing and fixing 15mm nominal bore C.P. brass stop
cock of standard design and approved make conforming to
I.S. : 8931.
Nos 6.0
N Supplying and fixing G.I. pipes, fittings with accessories
including plumbing fixtures, soil pipes, fittings with
accessories as per dirction .Payment will made on the basis
of actuals plus 15% towards handling, transporation,
storing, profit and over head charges.
PS 1.0
21.0 I P S
Providing and laying IPS which includes 25mm thick
PCC with 1:2:4 cement concrete laid to proper level and
slope including compactions, filling joints, finishing smooth
with cement mortar 1:1 of sufficient minimum thickness to
give a smooth & even surface
SFT 50.0
22.0 VITRIFIED TILES
Providing and laying 600mm x 600mm Vitrified Tiles
for Flooring of approved make and approved sample in
pattern as per detailed drawings up to 25mm thick bed of
1:4 cement mortar including surface preparation, giving
necessary slopes, cleaning joints aCost of Vitrified tile not to exceed Rs. 750/SMT inclusive
of delivery, Octroi, loading- Unloading at site and all taxes
thereon.
SFT 350.0
23.0 VITRIFIED TILES PATCHWORK
Providing and laying 600mm x 600mm Vitrified Tiles
for Flooring of approved Make and approved sample - as
patchwork as per the need at the site level Cost of Vitrified tile not to exceed Rs. 750/SMT inclusive
of delivery, Octroi, loading- Unloading at site and all taxes
thereon.
SFT 200.0
24.0 CERAMIC TILES - FLOOR
Providing and fixing 400 X 400 mm with necessary wall
plaining plastering, leveling what ever necessary to complete
the job as per instruction of the architect. Tiler basic rate
55.00/ sft. The rate is inclusive of providing and fixing
necessary backing materials, joint filling compound.
SFT 345.0
25.0 CERAMIC DADO TILES
Providing and fixing 300x200 mm on wall with necessary
wall plaining plastering, leveling what ever necessary to
complete the job as per instruction of the architect. Tiler
basic rate 30.00/ sft. The rate is inclusive of providing and
fixing necessary backing materials, joint filling compound.
SFT 285.0
26.0 DISPLAY PANELS
Providing & fixing in position frameless double acrlyic
trancparent sheet 2'-6”(l) x 1'-6”(w) mounted with mirror
scweres/nuts on the wall along with all accessories complete
for display of bank`s schemes/posters/notices inserted on
it.
NOS 2.00
27.0 PIN-UP BOARDS
Suppling and fixing pin-up boards fabricated out of 12 mm
BWR ply covered with 12mm soft board padding and
upholstered with poly propylene fabric @ Rs. 150/- per mt.
Edges of soft board should have t.w. Moulding duly spirit
polished.
SFT 10.00
28.0 WOODEN COUNTER FOR CANTEEN
Providing & supplying 1'6” wide wooden counter placed
against wall made of 18mm thick . Decoretive Laminate and
Badam wood liping standing on wooden posts and finished
with polis.
RFT 15.00
29.0 STAINLESS STEEL SINK
P/F/F Stainless steel sink with single bowl of Nirali
make,integrated waste size over all 600 x 450 mm with a
pair of C.I bracket,fitted with 15 mm dia. Brass C.P. Piller
tap & 32 mm dia white pvc waste pipe with brasscoupling
etc complete.
NO 1.00
30.0 KOTA STONE PANTRY COUNTER (2'-0” WIDE)
Providing & laying platform of 3/4” thk. & 2' didth (clear)and
at 2'-8” heiggt (top) above ffl. Of approved kota stone with
champhered and machine polished edge. It shall be on wall
on 1 1/2” thk horizontal kota stone. Rate shall include the
profile cutting andfixing of below counter wash
besin/kitchen sink and polishing the exposed edges of
granite. A 2” kota stone shall be provided below the
champhered edge.
RFT 9.00
31.0 TEXTURE PAINTING
Providing and applying textured painting combidec patern
i.e. Textured formed using tow or more approved shades (
sterling / spectrum or eqe. ) of approved shade and colour
on walls and columns in main banking hall form 900mm FFL
to ceiling height . The job is inclusive of scraping , leveling
and preparing the the surface , etc. complete . The work is
to be done strictly as per manufacturers specification.
SFT 150.00
T O T A L ON THIS BOQ
SR.NO DESCRIPTION UNIT QTY RATE (Rs.) AMOUNT (Rs.)
ESTIMATE
SUBMAIN WIRING
1 SWITCH FUSE UNIT
125 Amp. Nos 1.00
1.1 Main Power Panel Nos 1.00
1.2 Main Wiring upto
Main Power PanelWith 4C x 16 Sqmm
Flexible Copper Cable
from Main Meter to SFU
Mtr 15.00
With 3.5C X 50 Sqmm AL
Amroured Cable with GI
Earthing for FSU to MPP
Mtr 30.00
1.3 MCB DISTRIBUTION
BOARDs1.3.1 LDB ( 4 Way TPN DB )
Incoming : 32A 4P MCB
Out going : 10A SP MCB
with all complete
Nos 1.00
1.3.2 LDB ( 4 Way TPN DB )
Incoming : 32A 4P MCB
Out going : 10A SP MCB
with all complete
Nos 1.00
1.3.3 ACDB ,( 4 Way TPN DB )
Incoming : 32A 4P MCB
Out going : 10A P MCB
with all complete
Nos 2.00
1.3.4 UPS DB ( 8 Way SPN DB
) Incoming : 32A DP
MCB
Out going : 10A SP MCB
with all complete
No 1.00
1.4 SUBMAIN WIRING
With 2 nos 6 Sqmm + 1
No 4 Sqmm for UPS I/P
Mtr 15.00
With 2 nos 6 Sqmm + 1
No 4 Sqmm for UPS O/P
Mtr 8.00
PROJECT – BANK OF BARODA, PURULIA BRANCH
B O Q AND ESTIMATE DETAILS ELEC WORKS
With 3 nos 4 Sqmm + 1
No 2.5 Sqmm for Light /
Fan / Raw Power Dbs I/P
Mtr 15.00
1.5 CIRCUIT WIRING Mtr 100.00
1.6 PIONT WIRING
1.6.1 Light Point Each 35.00
1.6.2 Ceiling / Wall Mounted
Fan point. With
regulators
Each 12.00
1.6.3 Exhust Fan Point Each 2.00
1.6.4 5 pin 6A Switch
Shuttered Socket outlet
with switch on light / fan
switch board
Each 2.00
1.6.5 5 pin 6A Shuttered
Socket with 6A switch on
separate switch board
other than light / fan
switch board
Each 7.00
1.6.6 1.6.6 Call Bell Point with
Bell push
Each 2.00
1.8 A.C. POWER POINT Each 8.00
1.9 EARTHING GENERAL Each 1.00
SITC of earth station
with 50mm dia G.I. Pipe
3.64 mtr thick thick &
3.04 mtr.long and
1x4swg gi wire (4mtr
long) 13mm dia x 80mm
long g.i. Bolts, double
nuts double washers
including 15mm G.I. Pipe
protections (1mtr long)
to be filled with salt &
charcoal and driven to
an average depth of 3.65
mtr below the ground
level including brick
masionary chamber and
hinged c1 cover as per is
3043
1.9.1 Earth Lead -in -strip with
supply of 30X30 mm G.I
strip having PVC Sleeved
with clamps / Saddles at
an interval of 300mm
Mtr 10.00
1.9.2 Earthing Interconnection
between DBs and from
Earth bus bar to DBs
with 8 Swg bare copper
conductor
Mtr 8.00
2.0 SUPPLY AND
INSTALLATION OF
LIGHT FITTINGa 2 X 18 W ROUND CFL Each 14.00
b 2 X 36 W SQ LGHT
FITTING (2' X 2' )
Each 20.00
c 50w spot Each 3.00
d t5 light for cove light Each 6.00
e WALL MOUNTED TUBE
LIGHT FITTING
Each 12.00
2.3 SUPPLY AND
INSTALLATION OF
FAN FITTING2.3.1 Supply and iInstallation
of 1200/1400 mm sweep
ceiling fan with all
complete
Each 0.00
2.3.2 Supply and Installation
of 100/150 mm dia.
Exhust fan with all
complete
Each 2.00
2.3.3 Supply and Installation
of 400 mm dia. Heavy
Duty wall mounted Fan
with all complete
Each 12.00
2.4 Supply and Installation
of wall call bell buzzer
with al complete.
Each 2.00
C. COMPUTER POWER
WIRING3 SUBMAIN WIRING
2 nos 4 sqmm + 1 no
2.5 sqmm pvc insulated
FRLS copper conductor
in suitable PVC conduit
Mtr 90.00
3.1 COMPUTER SOCKET
OUTLET CLUSTER
POINT WIRING
Set 9.00
3.2 EARTHING (
COMPUTER )SITC of earth station
with 50mm dia G.I. Pipe
3.64 mtr thick thick &
3.04 mtr.long and
1x4swg gi wire (4mtr
long) 13mm dia x 80mm
long g.i. Bolts, double
nuts double washers
including 15mm G.I. Pipe
protections (1mtr long)
to be filled with salt &
charcoal and driven to
an average depth of 3.65
mtr below the ground
level including brick
masionary chamber and
hinged c1 cover as per is
3043
Each 1.00
3.2.3 Earth Lead -in -strip
withs supply and fixing
of 30mm X 6mm CU
strip having PVC sleeved
/ insulated to be fixed
with saddles / clamps at
an intervals of 300 mm
complete in all respect.
Mtr 10.00
3.2.4 Earthing Interconnection
between DBs and from
Earth bus bar to DBs
with 8 Swg bare copper
conductor
Mtr 20.00
4 TELEPHONE SOCKET NO 2.00
4.1 Telephone Junction Box No 1.00
4.2 Telephone Wiring Mtr 70.00NOTE:- ALL RATES ARE
INCLUSIVE OF DISMANTLING
NECESSARY EXISTING ITEMS,
REMOVAL AND DISPOSAL FROM
SITE TO THE MUNICIPAL
DUMPING GROUND.
T O T A L ON THIS
BOQ
REFURBISHMENT WORK OF PURULIA BRANCH
GENERAL SUMMARY
SECTION WORK AMOUNT
SECTION I CIVIL,INTERIOR
SECTION II ELECTRICAL
GRAND TOTAL
