GES-162Gigabit Ethernet Switch

GES-162_BR_E_1712_V1__.indd 1 2017. 12. 22. 오후 5:59

Gigabit Ethernet Switch

GES-162Network switch optimized for Collaboration System

x16

1G SFP2Port

PnPUnmanaged

JUMBO

RACK

DCACRear

placement Fan-less

GES-162_BR_E_1712_V1__.indd 2 2017. 12. 22. 오후 5:59

The GES-162 L2 switch supports 1000Mbps Gigabit, fully supports various environments using standard of 10 / 100 / 1000Mbps and full-Duplex function, which provides maximum switching capacity of 2000Mbps per port, total 36Gbps It is a high performance product of specifi cation.

Leveraging optical modules with Gigabit Ethernet ports and SFP ports, it provides scalability for faster network confi guration.

Supporting STP on all ports including all SFP ports, stable communication is possible even in a complicated network environment, and logical bandwidth integration is possible, so a more diverse network environment can be confi gured.

In addition, it is designed for low power, low heat and low noise to maintain excellent performance and system stability in any environment, and stable operation even in emergency situations through power redundancy.

The GES-162 switch is a convenient and powerful solution for network environment construction and management convenience.

GES-162_BR_E_1712_V1__.indd 3 2017. 12. 22. 오후 5:59

• 16-port Gigabit capable Ethernet transmission with line rate forwarding

• Fiber-based gigabit transport to SFP 2 ports using mini GBIC modules• Supports 10 / 100 / 1000Mbps standard tri-speed

• Unmanaged system provides easy connectivity and ease of use

• Up to 9Kbytes jumbo frame support for dramatic improvement in transmission speed

• Link aggregation function for large capacity switching and stability improvement

• Spanning Tree Protocol function prevents loops of data

• 1U suitable for rack

• Redundant power supply through DC power supply in case of emergency

• Improved installation and wiring convenience through rear connection of connectors

• Improved energy management with lower power consumption

• Cooling system with minimal heat support for operating temperatures up to 40 ° C• Fanless design eliminates the need for fans• Reliable service and fl exible network confi guration management

FEATURES

x

O

t

s

x16

1G

SFP2Port

PnPUnmanaged

JUMBO

RACK

DCAC

Rearplacement

Fan-less

GES-162_BR_E_1712_V1__.indd 4 2017. 12. 22. 오후 5:59

Inter-M GES-162 L2 Switch

- Reduced operating system and add-on cost

- Reduced operational burden through non-setup PnP

- Separate manpower and resource requirements are low

- Reduced cleaning and maintenance burden

- High stability and uptime

- Works smoothly regardless of location and environment

- Convenience in installation and maintenance of Rack

- Easy confi guration of Rack equipment and easy cable arrangement

- Can be used in conjunction with our PD series

- DC power supply eliminates the need for a separate AC UPS purchase

- Ensure operational stability through power redundancy

Other company products

- Product price increases due to operating system and add-ons

- Periodic management and professional operation personnel required

- Possibility of error in operating system or program

- Dust-sucking fan with limited build options

- As the temperature increases, the fan speed increases and the noise increases.

- Cleaning and maintenance burden exists

- It is diffi cult to connect and organize cables when confi guring rack equipment

- It is impossible to simultaneously check the status of broadcasting equipment and switch

- Unable to operate due to power failure due to single power supply

- Purchase a separate AC UPS for emergency situations

Unmanaged

Fanless

Rear Connection

Terminal

RedundancyDC Power

DIFFERENTIATION OF Inter-M PRODUCTS

GES-162_BR_E_1712_V1__.indd 5 2017. 12. 22. 오후 5:59

Port status LED (1~16) SFP port status LED (2Port)

Operation status LED Power indicator LED

AC power input connector (AC 120-240V, 50/60Hz) AC power switch DC 24V power input terminal

(EURO type 4P terminal block)

LAN ports (16 ethernet port, 10/100/1000Mbps) SFP ports

(For connecting two optical cables using GBIC)

FRONT&REAR

FRONT PANEL

REAR PANEL

GES-162_BR_E_1712_V1__.indd 6 2017. 12. 22. 오후 5:59

Support Feature

Switching Fabric Capacity (Gbps) 36Gbps

Forwarding Capacity (Mpps) 26.786Mpps

DRAM Capacity 128MB

Flash Memory Capacity 16MB

10/100/1000Mbps UTP Supported Port 16 Ports

SFP Supported Port 2 Ports

Booting Time 16 Seconds

Jumbo Frame 9KB

Link Aggregation Support

Spanning Tree Protocol Support

Operating Power AC 120-240V, 56Hz/60Hz, 14WEURO : DC 24V, 700mA

Operating Temperature -10°C ~ +40°C

Operating Humity 10 ~ 90%

Power Consumption Max 36W

Weight (Set) 3.2kg

Dimensions (Set) 482(W) x 44(H) x 280(D) mm

SPECIFICATION&DIMENSIONS

280

440

482

4428

0

AC POWER SWITCH DC INPUT

AC INPUT AUDIO OUTPUT LAN PORT

SPECIFICATION

DIMENSIONS

GES-162_BR_E_1712_V1__.indd 7 2017. 12. 22. 오후 5:59

It is a communication standard for telecommunication and data communication . It is optimized for long distance transmission. So, install a product with SFP terminal in a place where traffi c load is heavy, connect the optical cable to the SFP terminal , Speed communication is possible.

Fiber-based gigabit transport can be achieved using GBIC modules that support the SFP specifi cation.

Type Mode WavelengthMax Transmission

DistanceMax Transmission

Speed

SX Multi 850nm 550m 1.25Gbps

LX Single 1310nm 10km

2.5GbpsEX Single 1310nm 40km

ZX Single 1550nm 80km

EZX Single 1550nm 120km

- Multi-mode : Wide range of cores to use multiple optical signals- Single-mode : The core is narrow and only one optical signal is used

mini GBIC(SFP) Multi TypeMax transmission Distance 550m

LC type connector available

mini GBIC(SFP) Single TypeMax transmission Distance 10km

LC type connector available

SFP

• SFP Type

• SFP Modules

• Optical Cable Type

GES-162 TERM DESCRIPTIONS

GES-162_BR_E_1712_V1__.indd 8 2017. 12. 22. 오후 5:59

The technique of increasing the size of the data frame transmitted at a time, which transmits the same data in a larger unit, thereby improving the transmission speed.

The GES-162 switch automatically detects jumbo frames on Gigabit Ethernet and supports jumbo frames of up to 9KBytes, dramatically improving transmission speed.

In order to use this function, you need to set Jumbo frame in both network device and PC card.

- Normal Frame : You can transfer up to 1.5KBytes of capacity at a time.For example, when 8KB data is transmitted, it is transmitted over 6 times in units of 1.5KB.

- Jumbo Frame : You can transfer up to 9KBytes of capacity at a time.For example, 8KB data transfer is less than 9KB, so it is transmitted once.* 6 times faster than normal frame per unit time.

Jumbo Frame

• Capacity vs. Speed

8KB

8KB 8KB

NormalFrame

(1.5KB)

Jumbo Frame(9KB)

1.5KB 1.5KB 1.5KB •••

GES-162_BR_E_1712_V1__.indd 9 2017. 12. 22. 오후 5:59

LACP 2000Mbps Bandwidth Connection

LACP 4000Mbps Bandwidth Connection

Link aggregation (LACP)It groups multiple physical ports into groups, logically recognizes them as a single port, increases bandwidth, and uses them for various failover purposes.

The increased bandwidth does not mean the speed of the network is faster, but it does notslow down the bandwidth as much as the amount of simultaneous transmission, and distributes the load to make the device stable.

To use this function, you need to set LACP for both network device and PC card.

• LACP Con� guration

GES-162 TERM DESCRIPTIONS

GES-162_BR_E_1712_V1__.indd 10 2017. 12. 22. 오후 5:59

- Repeated broadcasts cause infi nite network failures

- Loop prevention with logical disconnection and failover with automatic path switching

Spanning Tree Protocol (STP)This is a technique to prevent loops that occur when there are multiple routing paths in a network environment consisting of switches.

In order to prevent the loop phenomenon, STP is used to cut off some paths when the paths between the switches are circulated. In this case, the path that is used is restored to the path that was disconnected in case of failure, so that continuous communication is possible.

This function can be used without setting.

• STP not supported, loop status

• STP applied, Loop canceled state

GES-162_BR_E_1712_V1__.indd 11 2017. 12. 22. 오후 5:59

EthernetIt is the most typical bus structure LAN (Local Area Network). It is the network confi guration method which occupies the vast majority in the short distance communication environment such as offi ce, school and so on.

Switch & HubThe hub acts as a simple repeater.

Because it does not store the MAC address of the connected device, it sends out packets to all devices connected to the hub, wasting a lot of bandwidth.

The switch stores the MAC address (MAC table) and transmits the signal only to the destination, so the bandwidth of the line can be fully used.

In other words, the more nodes connected and the more important the performance, the more you must use the switch.

L2 Switch

Switching based on MAC information performs switching functions such as Ethernet and Frame Relay, which are protocols of Layer 2 layer (Datalink).

LAN & WANThe LAN is a local area network. The internal network and the intranet belong here and are confi gured through switches, NIC (Network Interface Card, LAN card), and UTP cable.

A wide area network (WAN) is an external network, the Internet belongs here, and a router is added to the external network and the Internet confi guration to lease the line to an ISP.

GES-162 TERM DESCRIPTIONS

GES-162_BR_E_1712_V1__.indd 12 2017. 12. 22. 오후 5:59

Unmanaged SwitchUnmanaged switches do not have an operating system and UI to control the device, so they faithfully perform the functions of the switch itself.Because it is low cost and does not require a separate setup process, it is advantageous that you can operate it simply by connecting through Plug & Play (PnP).

The GES-162 switch can withstand the appropriate temperature, humidity and shock. It is suitable for industrial equipment which needs low power, low heat and low noise operation.

Giga BitThe next version of 100Base-TX standard, 100Mbps, which has a speed of 1000Mbps or higher.

Theoretically, you can get about 125MB of data per second at 10 times faster than a 100 Mbps network, but in fact, it is 3-5 times faster than the 100Mbps communication speed due to data processing and disk I / O.

When confi guring a Gigabit network environment, you can expect higher performance if you also confi gure Jumbo Frames.

In order to use this function, both the network device and the PC card used must support Gigabit Ethernet.

GES-162_BR_E_1712_V1__.indd 13 2017. 12. 22. 오후 5:59

APPLICATIONS

(1) Factory Complex (Network Converter + GES-162)In order to operate the broadcasting system of the large - scale factory complex in a stable manner, the optical communication network was constructed through the SFP terminal of GES-162. The ring topology can be used to neutralize the optical network and to operate the broadcasting system reliably in case of emergency or communication problems.

In order to control the detailed area within the factory complex, the GES-162 can be used as a network convertersystem to work with 6000 systems installed in each region.

Main Building

Factory B

Factory A Domitory

Sources Broadcasting Room

SPEAKER

SPEAKER

SPEAKER

SPEAKER

SPEAKER

Control PC

Audio(MIC/LINE)

Contact

RS-232/422/485

Network

Fiber Optical

GES-162_BR_E_1712_V1__.indd 14 2017. 12. 22. 오후 5:59

(2) School Campus (Network Converter + GES-162)Using the existing school network, elementary schools can deliver their own broadcasts to Kindergarten, which is an attached building.

To apply various network converters, GES-162 can be connected to the school's computer network and broadcasts such as guiding messages and BGM can be transmitted from the existing 6000 system to the kindergarten own broadcasting system.

Elementary School Kindergarden

School

Network

Audio(MIC/LINE)

Audio(LOW/HIGH-Z)

Contact

Network

Elementary School

Kindergarden

GES-162_BR_E_1712_V1__.indd 15 2017. 12. 22. 오후 5:59

APPLICATIONS

(3) Performance Hall Sound System (Dante™+GES-162)If you are transferring audio to the Dante™ network when you build a venue, you can transfer multi-channel high-quality audio over a single UTP instead of wiring conventional complex audio cables.

In addition, when events such as performances and speeches occur in the main hall, you can confi gure the optical network with GES-162 to play audio in real-time in a remote annex.

Hall

Annex

DAC-288

CDR-01

DX2042

DAC-288

GES-162

MIC

GES-162

DAC-122

CSP-4.8

SPEAKER

SPEAKER

SPEAKER

Audio

Network

Fiber Optical

GES-162_BR_E_1712_V1__.indd 16 2017. 12. 22. 오후 5:59

(4) CCTV Broadcasting SystemIf CCTV is used to manage outlying areas, the GES-162 can send and receive video and broadcasting systems for integrated management.

The images transmitted by the IP camera are managed through the control room, and the 6000 system can transmit the self-broadcasting of each region for guidance / emergency broadcasting.

Even when there is a problem in communication such as an emergency situation in a large remote area, the optical network is duplicated with the ring topology confi guration provided by GES-162 in order to operate a stable broadcasting system.

Control Center

GES-162

IP IP

IP IP

IP IP

IP IP

Outer Area #1

Outer Area #3

Outer Area #2

Outer Area #4

Audio

Contact

Network

Fiber Optical

GES-162GES-162

GES-162GES-162

GES-162_BR_E_1712_V1__.indd 17 2017. 12. 22. 오후 5:59

NOTE

GES-162_BR_E_1712_V1__.indd 18 2017. 12. 22. 오후 5:59

NOTE

GES-162_BR_E_1712_V1__.indd 19 2017. 12. 22. 오후 5:59

GES-162

Inter-M Corp. (IMK)719, Dobong-ro, Dobong-gu, Seoul, KoreaOverseas Sales TeamTel_ +82-2-2289-8141~7 Fax_ +82-2-2289-8149 E-mail_ overseas@inter-m.com www.inter-m.com

※ Design and speci� cation are subject to be changed for the improvement of product quality without pre notice. 2017. 12. V1

GES-162_BR_E_1712_V1__.indd 20 2017. 12. 22. 오후 5:59