geometry - virginia department of...
TRANSCRIPT
Property of the Virginia Department of Education
Copyright ©2015 by the Commonwealth of Virginia, Department of Education, P.O. Box 2120, Richmond, Virginia
23218-2120. All rights reserved. Except as permitted by law, this material may not be reproduced or used in any form or
by any means, electronic or mechanical, including photocopying or recording, or by any information storage or retrieval
system, without written permission from the copyright owner. Commonwealth of Virginia public school educators may
reproduce any portion of these released tests for non-commercial educational purposes without requesting permission.
All others should direct their written requests to the Virginia Department of Education, Division of Student Assessment
and School Improvement, at the above address or by e-mail to [email protected].
GEOMETRY
VIRGINIA STANDARDS OF LEARNING
TEST ITEM SET
Released Spring 2015
2009 Mathematics Standards of Learning
1 of 45
2 of 45
3 of 45
4 of 45
5 of 45
6 of 45
7 of 45
8 of 45
9 of 45
10 of 45
11 of 45
12 of 45
13 of 45
14 of 45
15 of 45
16 of 45
17 of 45
18 of 45
19 of 45
20 of 45
21 of 45
22 of 45
23 of 45
24 of 45
25 of 45
26 of 45
27 of 45
28 of 45
29 of 45
30 of 45
31 of 45
32 of 45
33 of 45
34 of 45
35 of 45
36 of 45
37 of 45
38 of 45
39 of 45
40 of 45
41 of 45
42 of 45
43 of 45
44 of 45
45 of 45
Sequence Number
Item Type: Multiple Choice
(MC) or Technology-Enhanced Item (TEI)
Correct Answer Reporting Category Reporting Category Description
1 MC B 001 Reasoning, Lines, and Transformations2 MC A 001 Reasoning, Lines, and Transformations3 TEI Answers must be placed in this order from top to bottom: 001 Reasoning, Lines, and Transformations
4 MC B 001 Reasoning, Lines, and Transformations5 MC B 001 Reasoning, Lines, and Transformations
GeometryReleased Test Item Set Spring 2015
Answer Key
Geometry Page 1
Sequence Number
Item Type: Multiple Choice
(MC) or Technology-Enhanced Item (TEI)
Correct Answer Reporting Category Reporting Category Description
6 MC A 001 Reasoning, Lines, and Transformations7 MC B 001 Reasoning, Lines, and Transformations8 MC B 001 Reasoning, Lines, and Transformations9 MC D 001 Reasoning, Lines, and Transformations10 MC D 001 Reasoning, Lines, and Transformations11 MC A 001 Reasoning, Lines, and Transformations12 TEI Typed response: 25 (and all equivalent answers) 001 Reasoning, Lines, and Transformations
13 MC D 001 Reasoning, Lines, and Transformations14 MC C 001 Reasoning, Lines, and Transformations15 MC A 001 Reasoning, Lines, and Transformations16 MC C 002 Triangles
Geometry Page 2
Sequence Number
Item Type: Multiple Choice
(MC) or Technology-Enhanced Item (TEI)
Correct Answer Reporting Category Reporting Category Description
17 TEI
Both of these answers, and only these answers, must be selected.
002 Triangles
18 MC A 002 Triangles19 MC B 002 Triangles20 MC A 002 Triangles21 MC C 002 Triangles22 MC C 002 Triangles23 MC C 002 Triangles
Geometry Page 3
Sequence Number
Item Type: Multiple Choice
(MC) or Technology-Enhanced Item (TEI)
Correct Answer Reporting Category Reporting Category Description
24 TEI Measures must be placed in the correct order from left to right, top to bottom: 20 cm; 29 cm; 21 cm OR 21 cm; 29 cm; 20 cmOne of these answers is shown below.
002 Triangles
25 MC C 002 Triangles
Geometry Page 4
Sequence Number
Item Type: Multiple Choice
(MC) or Technology-Enhanced Item (TEI)
Correct Answer Reporting Category Reporting Category Description
26 TEI Answers must be placed in the correct order from left to right: 002 Triangles
27 MC D 002 Triangles28 MC D 002 Triangles29 MC B 003 Polygons, Circles, and Three-Dimensional Figures30 MC A 003 Polygons, Circles, and Three-Dimensional Figures31 MC D 003 Polygons, Circles, and Three-Dimensional Figures
Geometry Page 5
Sequence Number
Item Type: Multiple Choice
(MC) or Technology-Enhanced Item (TEI)
Correct Answer Reporting Category Reporting Category Description
32 TEI Typed response: 27 (and all equivalent answers) 003 Polygons, Circles, and Three-Dimensional Figures
33 MC B 003 Polygons, Circles, and Three-Dimensional Figures34 MC A 003 Polygons, Circles, and Three-Dimensional Figures35 MC B 003 Polygons, Circles, and Three-Dimensional Figures36 MC C 003 Polygons, Circles, and Three-Dimensional Figures
Geometry Page 6
Sequence Number
Item Type: Multiple Choice
(MC) or Technology-Enhanced Item (TEI)
Correct Answer Reporting Category Reporting Category Description
37 TEIOne of these answers is shown below.
003 Polygons, Circles, and Three-Dimensional Figures
38 MC B 003 Polygons, Circles, and Three-Dimensional Figures39 MC C 003 Polygons, Circles, and Three-Dimensional Figures40 MC D 003 Polygons, Circles, and Three-Dimensional Figures41 MC D 003 Polygons, Circles, and Three-Dimensional Figures42 MC D 003 Polygons, Circles, and Three-Dimensional Figures
Geometry Page 7
Sequence Number
Item Type: Multiple Choice
(MC) or Technology-Enhanced Item (TEI)
Correct Answer Reporting Category Reporting Category Description
43 TEI are perpendicular (first row, first column); bisect each other (first row, second column); are congruent (first row, third column)All of these answers, and only these answers, must be selected.
003 Polygons, Circles, and Three-Dimensional Figures
44 MC C 003 Polygons, Circles, and Three-Dimensional Figures45 MC B 003 Polygons, Circles, and Three-Dimensional Figures
Geometry Page 8
868950 1 2 3 4 5 A B C D E Printed in the USA ISD6978