gemtek or greenpacket cpe quickstartup guide rev 1 0 2
TRANSCRIPT
Gemtek CPE Quick StartUp Guide
Quick Start
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
Gemtek CPE
Quick Start-Up Guide
Rev 1.0, Page 1 of 13
Gemtek CPE Quick StartUp Guide
When installing this equipment, observe the following precautions to minimize the danger of
personnel injury:
Danger:
• NEVER install equipment if there is a chance of lightning or other adverse weather
conditions.
• NEVER install in a wet location unless the equipment is specifically designed for wet
locations.
• NEVER touch un-insulated wires or terminals unless the w
the Network interface.
• ALWAYS use caution when installing or modifying cables.
ESD Warning:
• WARNING: Always assume that all components and assemblies are static sensitive and
always follow local ESD-prevention guidelines to pr
Note: This device must be professionally installed
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
SAFETY PRECAUTIONS
When installing this equipment, observe the following precautions to minimize the danger of
NEVER install equipment if there is a chance of lightning or other adverse weather
NEVER install in a wet location unless the equipment is specifically designed for wet
insulated wires or terminals unless the wire has been disconnected at
ALWAYS use caution when installing or modifying cables.
WARNING: Always assume that all components and assemblies are static sensitive and
prevention guidelines to prevent equipment damage.
This device must be professionally installed.
Rev 1.0, Page 2 of 13
When installing this equipment, observe the following precautions to minimize the danger of
NEVER install equipment if there is a chance of lightning or other adverse weather
NEVER install in a wet location unless the equipment is specifically designed for wet
ire has been disconnected at
WARNING: Always assume that all components and assemblies are static sensitive and
event equipment damage.
Gemtek CPE Quick StartUp Guide
Introduction
The Gemtek WIXS (TYPE 167 AND 177)
The outdoor CPE features dual polarization antenna to provide MIMO
A and Matrix-B. This combined with powerful RF circuit design,
outdoor environmental enclosure,
The unit’s characteristics are:
• Power Injector: Power over Ethernet 802.3af compliant
• LAN port: 10/100 Base Tx
• Output power: 27dBm
• Frequency bands
o 2.5 to 2.7GHz
o 3.3 to 3.6GHz
• Dual polarization:
o 3.65GHz, 14dBi Antenna
o 2.5GHz, 12dBi Antenna
• Supports IEEE 802.16e-2005 Scalable OFDMA based
• Channel bandwidths of 5 and 10MHz
• Supports WiMAX forum Matrix A/B MIMO in the Downlink and Collaborate MIMO in the
Uplink
• Provides users a seamless broadband wireless access
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
IXS (TYPE 167 AND 177) WiMAX CPE is a 802.16e fully compliant outdoor
dual polarization antenna to provide MIMO technology, both Matrix
with powerful RF circuit design, highly Integrated SW and robust
outdoor environmental enclosure, ensures a best in class outdoor coverage and throughput.
Power over Ethernet 802.3af compliant
: 10/100 Base Tx
3.65GHz, 14dBi Antenna
2.5GHz, 12dBi Antenna
2005 Scalable OFDMA based Technology
of 5 and 10MHz
Matrix A/B MIMO in the Downlink and Collaborate MIMO in the
Provides users a seamless broadband wireless access
Rev 1.0, Page 3 of 13
802.16e fully compliant outdoor CPE.
technology, both Matrix-
highly Integrated SW and robust
coverage and throughput.
Matrix A/B MIMO in the Downlink and Collaborate MIMO in the
Gemtek CPE Quick StartUp Guide
Installation and Setup
The Gemtek WIXS CPE is displayed in figure 1 below.
The installation instructions are provided below in figure
Figure 2 – Gemtek WIXS CPE Installation Instructions
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
CPE is displayed in figure 1 below.
Figure 1 – Gemtek WIXS CPE
The installation instructions are provided below in figure 2.
Gemtek WIXS CPE Installation Instructions
Rev 1.0, Page 4 of 13
Gemtek CPE Quick StartUp Guide
The Gemtek CPE contains an intergrated
connector is pointing directly down, then the units integrated antenna has the vertical
polarization plane pointing directly up and the horizontal polarization plane at 90 degrees right
angle. This direction of installation is best suited to Line of Sight and Near Line of Sight
installations.
In figure 1, the unit is installed in a “diamond” configuration with the RJ45 input connector
pointing down and to the side. This type of installation is best suited
installation where maximum benefit can be derived from the two antenna receivers.
The CPE is powered via a power over Ethernet 802.3af compliant device (refer to figure 3).
Figure 3
The factory default settings for the
• LAN IP: 10.1.1.254
• Netmask: 255.255.255.0
• LAN DHCP: enable
• User Name / Password: admin
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
The Gemtek CPE contains an intergrated dual polarization antenna. When the the RJ45 input
connector is pointing directly down, then the units integrated antenna has the vertical
directly up and the horizontal polarization plane at 90 degrees right
ion of installation is best suited to Line of Sight and Near Line of Sight
, the unit is installed in a “diamond” configuration with the RJ45 input connector
. This type of installation is best suited to a Non Line of Sight
installation where maximum benefit can be derived from the two antenna receivers.
The CPE is powered via a power over Ethernet 802.3af compliant device (refer to figure 3).
Figure 3 – Gemtek CPE PoE Injector unit
The factory default settings for the Gentek CPE are:
admin/admin
Rev 1.0, Page 5 of 13
dual polarization antenna. When the the RJ45 input
connector is pointing directly down, then the units integrated antenna has the vertical
directly up and the horizontal polarization plane at 90 degrees right
ion of installation is best suited to Line of Sight and Near Line of Sight
, the unit is installed in a “diamond” configuration with the RJ45 input connector
to a Non Line of Sight
installation where maximum benefit can be derived from the two antenna receivers.
The CPE is powered via a power over Ethernet 802.3af compliant device (refer to figure 3).
Gemtek CPE Quick StartUp Guide
The DHCP server on the CPE is enabled by default and therefore to
the host computer must meet the following requirements:
1) Equipped with an Ethernet network interface
2) Allow the client PC to obtain an IP address automatically or set a fixed IP address
3) Web browser installed: Mozilla Fiefox is recommended.
The CPE is configured with the default IP address of 1
255.255.255.0. Considering that the DHCP server is enabled by default, the DHCP clients should
be able to access the CPE, or the host PC should be assigned a static IP addre
configuration. An example for static IP address can be set to “
The CPE is managed through a web browser
web browser to allow you to set up and manage the device. The URL of
is: http://10.1.1.254.
It is recommended to use the “Mozilla Firefox” web browser rather than Internet Explorer to
access the unit. Known issues specifically with Internet Explorer Ver
the web browser display and configuration of the unit.
Unit Login
The following steps are required to login
1) Insert the PoE injector unit power cord and plug it into applicable “ac” power source.
2) Connect the “cross” Cat 5 Ethernet cable that shipped with
other end to the ““DATA
3) Connect one end of a “straight” Cat 5 Ethernet cable to the “D
injector unit and the other end can be connected to a PC or a network. V
few seconds, both LEDs (PORT and AC)
4) Make sure the PC’s IP address getting from
address is 10.1.1.254. In this example the address
5) Open the browser and input the web
login screen will appear (refer to figure 4)
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
is enabled by default and therefore to access the CPE
the host computer must meet the following requirements:
Equipped with an Ethernet network interface
Allow the client PC to obtain an IP address automatically or set a fixed IP address
Mozilla Fiefox is recommended.
is configured with the default IP address of 10.1.1.254 and subnet mask of
255.255.255.0. Considering that the DHCP server is enabled by default, the DHCP clients should
, or the host PC should be assigned a static IP address first for initial
configuration. An example for static IP address can be set to “10.1.1.100”.
through a web browser-based manager. It uses the HTTP protocol via a
web browser to allow you to set up and manage the device. The URL of management web site
It is recommended to use the “Mozilla Firefox” web browser rather than Internet Explorer to
access the unit. Known issues specifically with Internet Explorer Version 8 (IE8)
and configuration of the unit.
The following steps are required to login into the Gemtek CPE.
Insert the PoE injector unit power cord and plug it into applicable “ac” power source.
Connect the “cross” Cat 5 Ethernet cable that shipped with the CPE, to the CPE, and the
& POWER OUT” port of the PoE injector unit.
Connect one end of a “straight” Cat 5 Ethernet cable to the “DATA IN” port of the PoE
injector unit and the other end can be connected to a PC or a network. V
(PORT and AC) on the PoE injector unit light up bright green
Make sure the PC’s IP address getting from CPE DHCP server is 10.1.1.xxx. The default IP
. In this example the address 10.1.1.100/24 was used.
Open the browser and input the web control site: http://10.1.1.254 and
(refer to figure 4).
Rev 1.0, Page 6 of 13
CPE via Ethernet,
Allow the client PC to obtain an IP address automatically or set a fixed IP address
1.254 and subnet mask of
255.255.255.0. Considering that the DHCP server is enabled by default, the DHCP clients should
ss first for initial
uses the HTTP protocol via a
management web site
It is recommended to use the “Mozilla Firefox” web browser rather than Internet Explorer to
8 (IE8) can comprise
Insert the PoE injector unit power cord and plug it into applicable “ac” power source.
the CPE, to the CPE, and the
” port of the PoE
injector unit and the other end can be connected to a PC or a network. Verify that in a
on the PoE injector unit light up bright green .
.xxx. The default IP
was used.
and the Gemtek
Gemtek CPE Quick StartUp Guide
Figure 4 –
6) Enter the default Username and Password,
following Gemtek Web Browser Screen will be displayed
Figure 5 –
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
– Gemtek CPE Web Browser Login Screen
Enter the default Username and Password, these are “admin”, then click “Login”.
Web Browser Screen will be displayed (refer to figure 5)
– Gemtek CPE Web Browser Status Screen
Rev 1.0, Page 7 of 13
click “Login”.The
(refer to figure 5).
Gemtek CPE Quick StartUp Guide
7) The Gemtek Firware revision uppers in the upper right corner.
the Gemtek firmware is 4.6.1.0. If the revision
firmware must be upgraded.
CPE Firmware Upgrade
In the event that the firmware on the CPE unit has to be upgraded then please follow the steps as
outlined below.
1) Select the “Management” buttom wil appears directly b
Then sleect the “Upgrade”
open the screen as displayed in figure
Figure 6 – Gemtek
2) Click the “Browse” button, and navigate to the firmware image file
• For the Gemtek 2.5GHz model, the file is “BIMAGE.R4.6.1.0
167)”
• For the 3.65GHz model it is “BIMAGE.R4.6.1.0
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
The Gemtek Firware revision uppers in the upper right corner. The current
4.6.1.0. If the revision on the unit is anything else, the unit’s
irmware must be upgraded.
In the event that the firmware on the CPE unit has to be upgraded then please follow the steps as
Select the “Management” buttom wil appears directly below the Firmware Revision
the “Upgrade” button located down the left side of the screen.
open the screen as displayed in figure 6.
Gemtek CPE Web Browser Upgrade Screen
Click the “Browse” button, and navigate to the firmware image file (refer to figure 7)
For the Gemtek 2.5GHz model, the file is “BIMAGE.R4.6.1.0-20926
or the 3.65GHz model it is “BIMAGE.R4.6.1.0-20926-v5.7.22(WIXS
Rev 1.0, Page 8 of 13
current revision of
is anything else, the unit’s
In the event that the firmware on the CPE unit has to be upgraded then please follow the steps as
elow the Firmware Revision.
side of the screen. This will
(refer to figure 7).
20926-v5.7.22(WIXS-
v5.7.22(WIXS-177)”:
Gemtek CPE Quick StartUp Guide
Figure 7
3) Click on the “Upload” button. If the following screen appears, the unit is re
firmware upgrade (figure 8)
Figure 8 – Gemtek CPE Web Browser File Ready to Upgrade
4) Click on the “Apply” button at the bottom of this screen
After the upgrade finishes, the CPE will reboot.
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
Figure 7 – Gemtek CPE Upgrade File
button. If the following screen appears, the unit is re
(figure 8).
Gemtek CPE Web Browser File Ready to Upgrade
“Apply” button at the bottom of this screen. This will start the upgrade.
After the upgrade finishes, the CPE will reboot.
Rev 1.0, Page 9 of 13
button. If the following screen appears, the unit is ready for
start the upgrade.
Gemtek CPE Quick StartUp Guide
Unit Configuration
There are a lot of user configurable options available but to bring the unit to an operational
state is a relatively simple task.
To initially configure the unit, then please select the “
(refer to figure 9).
1) Click the “Stop” button, then the “Edit” button
2) This shows WiMAX settings for connecting to a Base Station. The
Bandwidth are variables that must match with those configured on the relevant Base
Station (figure 6).
3) Click the “Apply” button, then
Figure 9 – Gemtek CPE Web Browser WiMAX Configuration
Click on the “Status” button on the left hand menu (
communicates and connects with the Base Station it will transition through 4
• DL SYNCHRONIZATION
• UL ACQUISITION
• RANGING
• OPERATIONAL
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
There are a lot of user configurable options available but to bring the unit to an operational
To initially configure the unit, then please select the “WiMAX” button on the left hand menu
“Stop” button, then the “Edit” button.
This shows WiMAX settings for connecting to a Base Station. The Frequency
are variables that must match with those configured on the relevant Base
lick the “Apply” button, then “Close”, then the “Start” button.
Gemtek CPE Web Browser WiMAX Configuration
on the left hand menu (refer to figure 10). When the CPE
communicates and connects with the Base Station it will transition through 4 phases. These are:
Rev 1.0, Page 10 of 13
There are a lot of user configurable options available but to bring the unit to an operational
on the left hand menu
Frequency and
are variables that must match with those configured on the relevant Base
When the CPE
phases. These are:
Gemtek CPE Quick StartUp Guide
Figure 10 –
To configure the device for the purposes of management, the User will need to configure the
settings of the LAN (Local Area Network) interface for the device.
To change the LAN IP address then
1) Click on the “Networking” button on the
2) Select “Bridge/NAT Mode” from the list of options down the left.
3) Select “Bridge Mode” from the pull down m
4) Select “IP Type” as “Static”.
5) “IP Address”: Enter the required IP address, 192.168.2.102
6) “Netmask”: Enter a suitable subnet mask
7) Click the “Apply” button, and Reboot the unit.
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
– Gemtek CPE Web Browser WiMAX Status
To configure the device for the purposes of management, the User will need to configure the
Network) interface for the device.
To change the LAN IP address then:
ick on the “Networking” button on the left hand menu (refer to figure
Select “Bridge/NAT Mode” from the list of options down the left.
Select “Bridge Mode” from the pull down menu.
Select “IP Type” as “Static”.
“IP Address”: Enter the required IP address, 192.168.2.102
“Netmask”: Enter a suitable subnet mask
lick the “Apply” button, and Reboot the unit.
Rev 1.0, Page 11 of 13
To configure the device for the purposes of management, the User will need to configure the IP
figure 11).
Gemtek CPE Quick StartUp Guide
Figure 11 – Gemtek CPE Web Browser Management Static IP Configuration
If the User selects an “IP Type” of “DHCP” (see figure x), then the IP Address will be assigned via DHCP.
Unless the User knows what address has been assigned, then there will be no way to manage the unit
(refer to figure 12).
Figure 12 – Gemtek CPE
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
Gemtek CPE Web Browser Management Static IP Configuration
If the User selects an “IP Type” of “DHCP” (see figure x), then the IP Address will be assigned via DHCP.
Unless the User knows what address has been assigned, then there will be no way to manage the unit
Gemtek CPE Web Browser Management DHCP IP Configuration
Rev 1.0, Page 12 of 13
Gemtek CPE Web Browser Management Static IP Configuration
If the User selects an “IP Type” of “DHCP” (see figure x), then the IP Address will be assigned via DHCP.
Unless the User knows what address has been assigned, then there will be no way to manage the unit
Web Browser Management DHCP IP Configuration
Gemtek CPE Quick StartUp Guide
To enable the feature that will permit management access to the CPE from the Base Station
remotely from a WAN access (refer to figure 13)
1) Click on the “Firewall” button
2) Enable “Allow Web accessing from WAN”
3) Enable “Allow Telnet accessing from WAN”
4) Do not enable any other settings
5) Click the “Apply” button, and Reboot the unit.
Figure 13 – Gemtek CPE Web Remote Management Configuration
Gemtek CPE Quick StartUp Guide Rev 1.0, Page
To enable the feature that will permit management access to the CPE from the Base Station
(refer to figure 13).
lick on the “Firewall” button
nable “Allow Web accessing from WAN”
“Allow Telnet accessing from WAN”
o not enable any other settings
lick the “Apply” button, and Reboot the unit.
Gemtek CPE Web Remote Management Configuration
Rev 1.0, Page 13 of 13
To enable the feature that will permit management access to the CPE from the Base Station
Gemtek CPE Web Remote Management Configuration