gd&t symbols and guidelines cheat sheeteon.sdsu.edu/~johnston/gdtwallchart.pdf · orientation...
TRANSCRIPT
ORIE
NTAT
ION
FORM
LOCA
TION
PROF
ILERU
NOUT
A
A
0.03
0.03
0.03
0.03
0.03
10±0.050
10±0.05
A
A
0.03
0.03
0.03
0.03
25.0
25.0
Two parallel planes0.030 apart
Two concentric circles0.03 apart
Two parallel lines0.03 apart
Two parallel planes0.03 apart
Two parallel planes0.03 apart
Datum A
AxisTolerance Zone
at
10±0.05
10±0.05
0.03
M
Cylindrical Tolerance Zone0.03 when Part Ø= 10.050.13 when Part Ø = 9.95
Datum A
Datum A60°
Datum A
Datum A
Two concentric cylinders0.03 apart
Two parallel planes0.03 apart
Uniform Linear Boundary About True Profile0.03 apart
Datum B
Datum A
Datum ATolerance Zone
Uniform Surface Boundary About True Profile0.03 apart
Datum B
Part
Gauge
Datum axisMeasured axis
A
A
A
A0.03
0.03
0.03
A
Two parallel planes0.03 apart
A
Datum AFixed axially+ Rotated
A
Datum AFixed axially+ Rotated
Datum AFixed + Rotated
A
A
Gauge must follow true profile.
Profile is usually measured with a CMM.
Gauge ID = 10.08
Cylinder Gauge ID = M +
Bonus tolerance
60° GaugeBlock
60°
Gauge must follow true profile.
Profile is usually measured with a CMM.
90°
Gauge pininsertedperpendicular to datum
Pin Gauge Ø = 9.92(9.95 - 0.03)
Pin Gauge OD = M −
0.03
Part (actual) position
Truecenter
Measure X and Y location and compare to the true position.
This formula must be less thanthe Ø True Position tolerance
(Actual X - True X)2 + (Actual Y - True Y)2√Y
X
Actual YTrue Y
Actual XTrue X
ActualHole Position
True position
Tolerance Zoneof Pin Gauge
Actual True
60°
A
A
A
A
A
A
A
A
B
B
A
A
B
B
A
A
A
A
A
A
B
B
C
C
M
0.03 M
0.03
Flat datum block(Datum A)
Flat datum block(Datum A)
Part
Gauge
0.03 M
Planar Tolerance Zone
= 10.08M +
Gauge spacingat Virtual Condition
ActualPin Position
True position
Tolerance Zoneof Hole Gauge
Datum AFixed + Rotated
A
1
The following is usually done with a CMM:
1. Determine Datum axis
2. Measure referenced surface
3. Determine if central axis falls in TZ
The following is usually done with a CMM:
1. Determine Datum plane
2. Measure both surfaces of features
3. Determine if midpoints fall in TZ
Datum APlane
A
20.0
10±0.05A B
B
C
C
0.03
30.0
A
0.03 M
90°
Basic dimensions (not shown) must be used to define the True Profile
Basic dimensions (not shown) must be used to define the True Profile
2X
FUNCTIONALGAUGING
For anExternalFeature
For anInternalFeature
1
All drawings made in first angle projection
Straightness(Surface)
Flatness(Surface)
Circularity
Cylindricity
Parallelism
Straightness(Derived Median Line w/ )M
Perpendicularity(Feature of Size w/ )M
Perpendicularity(Feature)
Angularity
Pro�le of a line
True Position
Concentricity
Symmetry
Runout
Total Runout
Pro�le of a surface
True Position (Maximum Material Condition)
Flatness(Derived Median Plane w/ )M
M
M
M
M
SYMBOL NAME ON DRAWING TOLERANCE ZONE GAUGING
GD&T Symbols and Guidelines Cheat Sheet
Copyright © 2017 GD&T Basics - www.gdandtbasics.com - Chart designed by Andrea Barbieri <www.andreabarbieri.net>
Provided by GD&T Basics - www.gdandtbasics.com