garage door manufacturing co. - construction data leads ...€¦ · midland garage door...

083613/MID

G a r a g e D o o r M a n u f a c t u r i n g C o .

Residential Sectional DoorsArchitectural Specifications

midlandgaragedoor.com

2

083613/MID

Midland Garage Door Manufacturing Company is dedicated to manufacturing the highest quality commercial and residential overhead sectional door products, and delivering those products on a timely basis through a well trained, qualified dealer network. Since 1978 Midland has manufactured thousands of doors, many of which have been installed in demanding service in military installations, fire departments, mines and other commercial and agricultural applications.

We welcome the opportunity to work with architects and design professionals and are pleased to answer any questions or discuss special needs you may have.

PROFILE

Architectural Specifications

3

083613/MID

MIDLAND LIMITED WARRANTYMidland warrants its products to be free from defects in materials and workmanship as follows.

RESIDENTIAL RSP & Flush 24ga & 2” TS Series -Midlandwarrantsthesesteelgaragedoorsectionsagainstrustthrough,paintfinishcrackingorpeelingtotheoriginal

purchaser for as long as they own the building in which the doors were installed. - All other components except springs are warranted for 5 years.

VALU CRAFT, TS 138 & R-26 -Midlandwarrantsthesesteelgaragedoorsectionsagainstrustthrough,paintfinishcrackingorpeelingtotheoriginal

purchaser for 15 years. - All other components except springs are warranted for 2 years.

COMMERCIAL -Midlandwarrantsitssteelgaragedoorsectionsusedincommercialapplicationsagainstrustthrough,paintfinish

cracking or peeling to the original purchaser for 10 years. - All other components except springs are warranted for 2 years. - Midland warrants components in a high cycle application for 1 year.

hARSh ENVIRONMENT - Midland warrants its polycarbonate and 3” ES sections that are used in harsh environment applications for 1 year. - Midland warrants its harsh environment components package for 1 year.

Midland warrants springs in all applications for 1 year to the original purchaser.

Midland warrants all its laminated sections against delamination for a period of 10 years to the original purchaser.

This warranty excludes the following: 1) Deteriorationduetorustresultingfromdamagetothegaragedoorsectioncausedbyfire,otheraccidentor

casualty, vandalism, harmful fumes or chemicals, condensation, or occurring as a result of any physical damage. 2) Failure of paint if any top coatings are applied to factory paint. 3) Onsite labor. 4) Freight charges. 5) Scratches or dents occurring after pick up or delivery from Midland. 6) Damage caused by improper installation, maintenance or product alteration. 7) Damage caused by misuse, abuse or accident. 8) Delamination as a result of a heat source too close to the garage door sections (eg heaters, lights, etc.) 9) Wear from normal operation.

The warranty of the manufacturer shall be limited to the repair or replacement only for such parts which may be acknowledged by the manufacturer to be defective.

To make a claim under this warranty contact your Midland dealer. A written claim accompanied by proof of purchase must be submitted within 30 days of discovery of the suspect defect. Midland may at its discretion send a representative to inspect the defective part and/or may request that the defective part be returned to the factory freight pre paid.

No warranty extends to consequential or incidental damages. All other express or implied warranties including any implied warrantyofmerchantabilityorimpliedwarrantyoffitnessforpurposeareherebyexpresslyexcluded.

This warranty applies to doors purchased after August 1, 2001.

Limited Warranty

4

083613/MID

® 2007 Midland Garage Door Mfg. Co., Inc. All rights reserved.Midlandgaragedoor.com 1-800-437-4056

Beauty, elegance, distinctive style and strength describe Midland's Custom

Design Series doors. These unique residential garage doors offer a wide

variety of choices in style ranging from traditional to carriage house designs.

This door represents a combined effort with JELD WEN the world leader in

composite technology for over thirty years. The advanced polymer skin and

trim boards won't crack, split, separate, shrink, expand, rust or dent. Extra-

wide LVL laminated support rails give these doors the strongest structural

support in the industry.

The factory thermal-set primer requires finish painting. You choose the

colors that compliment your home. The entire face of the door, regardless

of design, is made from the same material and made in the same plant

therefore the components are bonded for life and match and fit perfectly.

Built to be beautiful and move quietly and easily with Midland's smooth

torsion spring system. Each door panel rides on its own set of ultra quiet

residential rollers, that are fitted to a heavy duty track.

A garage door that is as tough as it is beautiful!

(consult dealer for factory design

information and warranty details)

MID

LA

ND

R

ES

IDE

NT

IAL

G

AR

AG

E

DO

OR

SCustom

Design Series (composite garage doors)

Choice of: TRADITIONAL or

CARRIAGE HOUSE DESIGNS

(optional decorative hardware shown)

5

083613/MIDArchitectural SpecificationsResidential Doors

Model: Classic Panel Classic Panel TS (2”Thermo-Steel)

I. GeneralA. Work IncludedThe doors will be Model Classic Panel-TS as manufactured by Midland Garage Door Mfg. Co.

B. Other WorkRelatedstructurework,openingpreparation,fieldpainting and electrical work etc. falls into the responsibility of other trades.

II. ProductA. SectionsSections will be roll-formed, hot dipped, galvanized G40 (minimum), a minimum yield strength of 33,000 psi, complying with ASTM A653, and ASTM A924. 26 ga. exterior and interior sheet steel. Classic panel design embossed pebble textured exteriorsurfaceandflushembossedpebbletexturedinterior surface. Sections will be pressure bonded to a polystyrene core and will have a thickness of 2”. Sections will incorporate a continuous dual durometer vinyl extrusion thermal-break separating exterior skins preventing heat or cold conductivity.

B. InsulationInsulation will be rigid 2” expanded polystyrene free of CFCs and hCFC’s and will be laminated, pressure bonded to provide strength and prevent lossofthermalefficiencyovertime.Theinsulationwill have calculated R-Value of 9.25 and U-Value of 0.108 complying with ASTM A236. Insulation material complying with ASTM E84 flame-spreaded and smoke-developed.

C. Glazing (Optional)Standard 1/8” or 1/2” insulatedDSB clear floatglass. Various design window lite patterns to choose from, consult factory.

D. WindloadDoors will be designed to meet or exceed industry standards for windloads (ANSI/DASM A102-1996), uniform pressure (velocity pressure) 20lbf/sq.ft.actinginwardandoutward.Deflectionof door in the horizontal position will not exceed 1/120 of the door width. Consult factory for unusual requirements.

E. HardwareHinges andfixtureswill beG-60galvanizedsteel complying with ASTM A36 and ASTM A123. Standard ultra quiet nylon rollers. Roller sizes will be adequate for design requirements and limitations.

F. StilesEnd stiles 16 ga. Intermediate hinge plate stiles 20 ga. under interior surface skin.

G. TrackTrack 2” bracket or angle mounted depending upon door size and requirements.

H. Spring CounterbalanceCounterbalance shall be oil tempered, helical wound torsion springs complying with ASTM A229, mounted on a ball bearing cross header shaft engineered to comply with ANSI/DASMA 102-1996. Longer life springs of 25,000, 50,000 or100,000cyclesmaybespecified.Galvanizedaircraft type lifting cables with a safety factor of 8 to 1.

I. LockLock will be standard interior mounted slide lock. (Optional residential exterior keyed handle lock assembly is available).

J. WeathersealsBottom weatherstrip will be U’d shape astragal fastened to the bottom of the door with an extruded aluminum holder for an effective seal at thesill.Optional jambandheaderflexiblevinyl weatherstripping.

K. FinishExteriorfinisheswillbe1-milthick,two-coat, baked-on polyester (.8 mil) top coat, over primer (.2 mil) on galvanized coating. Colors; Almond. Brown, hunter Green, Sandtone, Tera-bronze and White.

L. OperationOperation will be by manual pull rope. Optional electric operators are available.

M. Exterior DesignOptional black carriage door style steel hinges and decorative handles.

III. ExecutionInstallationDoors should be installed in compliance with Midland Garage Door Mfg. Co. instructions by authorized Midland Garage Door Installation Professionals.

Pebble Texture FinishExterior and Interior

6

083613/MIDArchitectural SpecificationsResidential DoorsModel: Raised Panel Flush Panel

RSP-TS & Flush-TS(2” Thermo-Steel)

I. GeneralA. Work IncludedThe doors will be Model Raised Panel T-S or Flush Panel-TS as manufactured by Midland Garage Door Mfg. Co.

B. Other WorkRelated structure work, opening preparation, fieldpaintingandelectricalworketc.fallsintothe responsibility of other trades.

II. ProductA. SectionsSections will be roll-formed, hot dipped, galvanized G40 (minimum), a minimum yield strength of 33,000 psi, complying with ASTM A653 and ASTM A924. 26ga. exterior and interior sheet steel. Raised and Flush panel design embossed pebble textured exterior surface andflush embossed pebble textured interiorsurface. Sections will be pressure bonded to a polystyrene core and will have a thickness of 2”. Sections will incorporate a continuous dual durometer vinyl extrusion thermal-break separating exterior skins preventing heat or cold conductivity.

B. InsulationInsulation will be rigid 2” expanded polystyrene free of CFCs and hCFC’s and will be laminated, pressure bonded to provide strength and prevent loss of thermal efficiencyover time.The insulation will have a calculated R-Value of 9.25 and U-Value of 0.108 complying with ASTM A236. Insulation material complying with ASTM E84 flame-spread and smoke-developed.

C. Glazing (optional)Standard1/8”or1/2”insulatedDSBclearfloatglass. Various design window lite patterns to choose from, consult factory.

D. WindloadDoors will be designed to meet or exceed industry standards for windloads (ANSI/DASM A102-1996), uniform pressure (velocity pressure) of 20lbf/sq. ft. acting inward and outward.Deflectionofdoor in thehorizontalposition will not exceed 1/120 of the door width. Consult factory for unusual requirements.

E. HardwareHingesandfixtureswillbeG-60galvanizedsteelcomplying with ASTM A36 and ASTM A123. Standard ultra quiet nylon rollers. Roller sizes will be adequate for design.

F. StilesEnd stiles will be 16 ga. steel. Intermediate hinge plate stiles 20ga. under interior surface skin.

G. TrackTrack 2” bracket or 2” or 3” angle mounted depending upon door size and requirements.

H. Spring CounterbalanceCounterbalance shall be oil tempered, helical wound torsion springs complying with ASTM A229, mounted on a ball bearing cross header shaft engineered to comply with ANSI/DASMA 102-1996. Long life springs of 25,000, 50,000 or100,000cyclesmaybespecified.Galvanizedaircraft type lifting cables with a safety factor of 8 to 1.

I. LockLock will be standard interior mounted slide lock. (Optional residential exterior keyed handle lock assembly is available).

J. WeathersealsBottom weatherstrip will be U’d shape astragal fastened to the bottom of the door with an extruded aluminum holder for an effective seal at thesill.Optionaljambandheaderflexiblevinylweatherstripping.

K. FinishExteriorfinisheswillbe1-milthick,two-coat, baked-on polyester (.8 mil) top coat, over primer (.2 mil) on galvanized coating. Colors; Almond, Brown, hunter Green, Sandtone, Tera-bronze and White.




7

083613/MIDArchitectural SpecificationsResidential DoorsModel: Raised Panel Flush Panel

TS-138 RSP & TS-138 Flush(1 3/8” Thermo-Steel)

I. GeneralA. Work IncludedThe doors will be Model Raised Panel TS-138 or Flush Panel TS-138 as manufactured by Midland Garage Door Mfg. Co.


II. ProductA. SectionsSections will be roll-formed, hot dipped, galvanized G40 (minimum), a minimum yield strength of 33,000 psi, complying with ASTM A653 and ASTM A924. 26 ga. exterior and interior sheet steel. Raised and Flush panel design embossed pebble textured exterior surface and flush embossed pebbletextured interior surface. Sections will be pressure bonded to a polystyrene core and will have a thickness of 1 3/8”. Sections will incorporate a continuous dual durometer vinyl extrusion thermal-break separating exterior skins preventing hear or cold conductivity. B. Insulation Insulation will be rigid 1 3/8” expanded polystyrene free of CFCs and hCFC’s and will be laminated, pressure bonded to provide strengthandpreventlossofthermalefficiencyover time. The insulation will have a calculated R-Value of 7.5 and U-Value of 0.133 complying with ASTM A236. Insulation material complyingwithASTME84flame-spreadandsmoke-developed.

C. Glazing (Optional)Standard 1/8” un-insulatedDSB clear floatglass. Various design window lite patterns to choose from, consult factory.

D. WindloadDoors will be designed to meet or exceed industry standards for windloads (ANSI/DASM A102-1996), uniform pressure (velocity pressure) of 20lbf/sq. ft. acting inward and outward.Deflectionofdoor in thehorizontalposition will not exceed 1/120 of the door width. Consult factory for unusual requirements.


F. StilesEnd stiles will be 18 ga. Intermediate hinge plate stiles 20 ga. under interior surface skin.


H. Spring CounterbalanceCounterbalance shall be oil tempered, helical wound torsion springs complying with ASTM A229, mounted on a ball bearing cross header shaft engineered to comply with ANSI/DASMA 102-1996. Standard springs minimum 10 – 12,000 cycles. Galvanized aircraft type lifting cables with a safety factor of 8 to 1.

I. LockLock will be standard interior mounted slide lock. (Optional residential exterior keyed handle lock assembly are available).

J. WeathersealsBottom weatherstrip will be U’d shape astragal fastened to the bottom of the door with an extruded aluminum holder for an effective seal at the sill.Optional jambandheaderflexiblevinyl weatherstripping.

K. FinishExteriorfinisheswill be 1-mil thick, two-coat, baked-on polyester (.8 mil) top coat, over primer (.2 mil) on galvanized coating. Colors; Brown, Sandtone, and White.




8


Model: Classic PanelSeriesClassic24

I. GeneralA. Work IncludedThe doors will be Model Classic Panel 24 as manufactured by Midland Garage Door Mfg. Co.


II. ProductA. SectionsSections will be roll-formed, hot dipped, galvanized G40 (minimum), a minimum yield strength of 33,000 psi, complying with ASTM A653, and ASTM A924. 24 ga. exterior sheet steel. Classic panel design. Embossed pebble textured exterior surface. Sections will be a thickness of 2”. Door sections will have a tongue and groove meeting rails to form weathertight joints.

B. Insulation (Optional)Insulation will be rigid 2” expanded polystyrene free of CFCs and hCFC’s. The insulation will have calculated R-Value of 7.0 and U-Value of 0.143 complying with ASTM A236. Insulation material complyingwithASTME84flame-spreaded and smoke-developed.

C. Glazing (optional)Standard 1/8” un-insulatedDSB clear floatglass. Various design window lite patterns to choose from, consult factory.

D. WindloadDoors will be designed to meet or exceed industry standards for windloads (ANSI/DASM A102-1996), uniform pressure (velocity pressure) 20lbf/sq. ft. acting inward and outward.Deflectionofdoorinthehorizontalposition will not exceed 1/120 of the door width. Consult factory for unusual requirements.

E. HardwareHingesandfixtureswillbeG-60galvanizedsteel complying with ASTM A36 and ASTM A123. Standard ultra quiet nylon rollers. Roller sizes will be adequate for design requirements and limitations.

F. StilesEnd and intermediate stiles will be 16 ga. Steel. Riveted and welded to the section. End stiles will be a channel-shaped to 2” deep.



I. LockLock will be standard interior mounted slide lock. (Optional residential exterior keyed handle lock assembly and mini-warehouse locks are available).

J. WeathersealsBottom weatherstrip will be U’d shape astragal fastened to the bottom of the door with an extruded aluminum holder for an effective seal at the sill.Optional jamb andheaderflexiblevinyl weatherstripping.

K. FinishExteriorfinisheswillbe1-milthick,two-coat, baked-on polyester (.8 mil) top coat, over primer (.2 mil) on galvanized coating. Colors; Almond. Brown, hunter Green, Sandtone, Tera-bronze and White.



Pebble Texture Exterior Finish

9


Model: Raised Panel Flush PanelSeries24

I. GeneralA. Work IncludedThe doors will be Model RSP-24 Raised Panel and Flush Panel FL-24 as manufactured by Midland Garage Door Mfg. Co.


II. ProductA. SectionsSections will be roll-formed, hot dipped, galvanized G40 (minimum), a minimum yield strength of 33,000 psi, complying with ASTM A653 and ASTM A924. 24ga. exterior sheet steel. Raised and Flush panel design. Embossed pebble textured exterior surface. Sections will be a thickness of 2”. Door sections will have a tongue and groove meeting rails to form weathertight joints.

B. Insulation (Optional)Insulation will be rigid 2” expanded polystyrene free of CFCs and hCFC’s. Insulation will have a calculated R-Value of 7.0 and U-Value of 0.143 complying with ASTM A236. Insulation material complyingwithASTME84flame-spread and smoke-developed.


D. WindloadDoors will be designed to meet or exceed industry standards for windloads (ANSI/DASM A102-1996), uniform pressure (velocity pressure) of 20lbf/sq. ft. acting inward and outward.Deflectionofdoorinthehorizontalposition will not exceed 1/120 of the door width. Consult factory for unusual requirements.


F. StilesEnd and intermediate stiles will be 16 ga. steel. Riveted and welded to the section. End stiles will be a channel-shaped to 2” deep.




J. WeathersealsBottom weatherstrip will be U’d shape astragal fastened to the bottom of the door with an extruded aluminum holder for an effective seal at the sill.Optional jamb andheaderflexiblevinyl weatherstripping.

K. FinishExteriorfinisheswillbe1-milthick,two-coat,baked-on polyester (.8 mil) top coat, over primer (.2 mil) on galvanized coating. Colors; Almond, Brown, hunter Green, Sandtone, Tera-bronze and White.




10


Model: Raised PanelValu-craft

I. GeneralA. Work IncludedThe doors will be Model RSP-25 Raised Panel as manufactured by Midland Garage Door Mfg. Co.


II. ProductA. SectionsSections will be roll-formed, hot dipped, galvanized G40 (minimum), a minimum yield strength of 33,000 psi, complying with ASTM A653 and ASTM A924. 25ga. exterior sheet steel. Raised panel design. Embossed pebble textured exterior surface. Sections will be a thickness of 2”. Door sections will have a tongue and groove meeting rails to form weathertight joints.





F. StilesEnd and intermediate stiles will be 16 ga. Steel. Riveted and welded to the section. End stiles will be a channel-shaped to 2” deep.




J. WeathersealsBottom weatherstrip will be U’d shape astragal fastened to the bottom of the door with an extruded aluminum holder for an effective seal at the sill. Optional jamb and header vinyl weatherstripping.

K. FinishExteriorfinisheswillbe1-milthick,two-coat, baked-on polyester (.8 mil) top coat, over primer (.2 mil) on galvanized coating. Colors; Almond, Brown, Sandtone, Tera-bronze and White.



Pebble TextureExterior Finish

11

083613/MIDArchitectural SpecificationsResidential DoorsModel: RibbedSeriesClassicR-26

I. GeneralA. Work IncludedThe doors will be Model R26 Ribbed as manufactured by Midland Garage Door Mfg. Co.


II. ProductA. SectionsSections will be roll-formed, hot dipped, galvanized G40 (minimum), a minimum yield strength of 33,000 psi, complying with ASTM A653 and ASTM A924. 26 ga. exterior sheet steel. Ribbed design, six shallow and two deep ribs. Embossed pebble textured exterior surface. Sections will be a thickness of 2”. Door sections will have a tongue and groove meeting rails to form weathertight joints.


C. Glazing (Optional)Standard 1/8” un-insulated or 1/2” insulated DSBclearfloatglass.Windowlitesizes24x5 and 24 x 12..



F. Stiles

End and intermediate stiles will be 16 ga. steel. Riveted and welded to the section. End stiles will be a channel-shaped to 2” deep.




J. WeathersealsBottom weatherstrip will be U’d shape astragal fastened to the bottom of the door with an extruded aluminum holder for an effective seal at thesill.Optional jambandheaderflexiblevinyl weatherstripping.

K. FinishExteriorfinisheswillbe1-mil thick, two-coat, baked-on polyester (.8 mil) top coat, over primer (.2 mil) on galvanized coating. Colors; Brown and White.




Midland 3" Energy Saver Doors Pictured Above

MIDLAND GARAGE DOOR MANUFACTURING COMPANY Omaha, NE Home Office: Chaska, MN (402) 895-6575 675 12th Ave. North (952) 368-3122 (WATS: 800-533-8358) West Fargo, ND 58078 (WATS: 800-521-0047) Phone (701) 282-8136 Wats: 800-437-4056 www.midlandgaragedoor.com

GARAGE DOOR MANUFACTURING CO.

Door & Access SystemsManufactures AssociationInternational

International Door AssociationDevelop and Promote Door Dealer Excellence

Midland Bi-Fold door division produces custom built doors to accommodate aircraft hangars, commercial and agricultural applications (contact factory for details).

Midland Bi-fold Doors

12

Midlandgaragedoor.com 1-800-437-4056® 2007 Midland Garage Door Mfg. Co., Inc. All rights reserved.

garage door manufacturing co. - construction data leads ...€¦ · midland garage door...

Documents