galaxy sq-270 sq-27… · 4 gal/min (1 bar = 4 gal/min) 0.5 - 5 bar 2.5 technical features....

Aquaticausa.comAquaticabath.caE: [email protected]

Installation & Care Manual

Built-In Shower Head

USA / Canada

Galaxy SQ-270


Galaxy SQ-270Built-In Shower Head

10.6"

9.4"

Ø 0.2"

G1/2

0.7"

2.4"

Ø 1.6"

25° 25°

9.6"

Ø 9.4"

WIRE WITHMALE CONNECTOR

SHOWERHEAD

POWER SUPPLY

ARTICULATED CONNECTION

16'-5"

4 SCREWS FIXING

POWER SUPPLY

4.6"

2'

1.4"

INPUT: ~ 100/240 V AC~ 50/60 Hz 0.55 A

OUTPUT: 12 V 1.67 A 20W

2'

PARTS LIST


Pressure required: ............................................

Limited flow rate: water consuntion ..................

Pipes connection: .............................................G 1/2"

Maximum absorbed power: ..............................MAX 9 Watt

Power supply: .................................................. INPUT: ~ 100/240 V AC

~ 50/60 Hz 0.55 A

OUTPUT: 12 V 1.67 A - 20W

Pressure [bar]

Flo

w r

ate

[gal/m

in]

FLOW RESTRICTOR WORKING

SCHEME RELATED TO WATER PRESSURE

0.0 1.0 2.0 3.0 4.0 5.0 6.00.00

1.00

2.00

3.00

4.00

5.00

No. of samples 2

[bar] 0.5 0.7 1.0 1.5 2.0 2.5 4.0 6.0

[gal/min] 3.01 3.38 3.64 3.77 3.8 3.84 3.97 4.03

0.5 1.5

ELECTRICAL SAFETY

- Installation must be performed by qualified and/or

trained personnel.

The company declines all responsibility in the case

that installation is performed by personnel that is not

trained and/or qualified to carry out installation of this

product.

- The responsibility for the choice of materials in

relation to their utilisation, the correct execution of

the work, the verification of the plant system to which

the device will be connected as well as its suitability

to guarantee safety, are the responsibility of the

installer.

-The power supply plant must be efficient and

conform to the legal provisions and to specific

national regulations.

For connection to the electrical mains, a single pole breaker switch must be installed, to be placed in an area that

respects safety provisions for bathroom areas.

-This single pole, normalised breaker switch must guarantee an opening of the contacts of at least 3 mm, and be

suitable for voltage of 220-240V and current up to 16 A.

- In bathrooms, the installation of electrical devices and equipment, such as switches, outlets, etc., must be in

adherence to the law and the regulations of each country. In particular no electrical installation may be placed in

the area directly adjacent to the shower stall for a distance of at least 2' and a height of 7'-5".

- The power supply electrical system must have a differential switch connected to it.

- Any damages caused by the lack of observance of the legal and regulatory provisions as well as what is indicated

in the instruction sheet will be the responsibility of the installer.

4 gal/min (1 bar = 4 gal/min)

0.5 - 5 bar

2.5

TECHNICAL FEATURES



min. 2'

A

min

. 7.4

'

Input current:

~ 100/240 V AC

~ 50/60 Hz 0.55 A

1/2" F

connection

Electrical

wire tube

B

=12 V DC

A = BOX FOR POWER SUPPLY

(not included)

- minimum sizes 6"x3.9"x2.7"

- see gewiss model art. GW48004

B = BOX FOR SWITCH (not included)

See the next sheet for this node

min. 2'

INSTALLATION SEQUENCE


- Never put the (~100/240 V) power supply input wires together in the same conduit pipe with the (=12 V) power

supply output wires that are then to be connected to the shower head wires.

Clamp

Wire connection

- 500 cm (included) LED wire connection

- 600 cm (included)

Water inlet

LED electricalcable

Switch to turn LED on and off

Ceiling Tube(Not included)

=12 V DC

Power Supply:

INPUT: ~ 100/240 V AC

~ 50/60 Hz 0.55 A

OUTPUT: 12 V 1.67 A 20W

=12 V DC

Input current:

~ 100/240 V AC

~ 50/60 Hz 0.55 A

Connectors

ATTENTION !

INSTALLATION SEQUENCE continued



a

5/6"

ba

PipeG1/2" F

3

1 1/4"

a

b

b

3/32"

a

Not included

Electrical cableconduit tube

ATTENTION:

- Before attaching the electrical power lines, check and verify the security of

the connections and the operation of the shower head.

- The ATTACHMENT of the SHOWER HEAD PANEL to the drop-ceiling

panels must guarantee the mechanical solidity of the shower head itself.

Attachment is performed by way of screws that are not supplied.It is

necessary to provide for an opening in the drop-ceiling panels, near the

shower head, which may be used, in the event of maintenance necessities,

access to the area above the drop-ceiling itself.

Electric wire

Screws fixing

Not included

1 2

4

INSTALLATION SEQUENCE continued


NOZZLES REPLACEMENT

Sylicon antilimestone

nozzles

The correct cleaning of the showerhead has to be done with water and

soap, rinsed and dried with a doeskin or a soft cloth. Absolutely do not use

alcohol, solvents, solid or liquid containing corrosive or acid substances

(hydrochloric, formic, acetic and phosphoric acid), synthetic fibres, cloths,

abrasive sponges and plugs with metallic thread, because they could

irreversibly alter the treated surfaces.

Our devices do not need any particular maintenance with the exception of

the periodic cleaning of the rubber part (nozzles) of the shower head, that

they

may become locked by formations of limestone just rub with your finger to

remove the limestone.

ATTENTION: periodically check the niples, as an excess of dirt in them

may generate extra pressure inside the shower head compromising the

operation.

a b

c

1 2

3

A

B

C

CLEANING AND MAINTENANCE

galaxy sq-270 sq-27… · 4 gal/min (1 bar = 4 gal/min) 0.5 - 5 bar 2.5 technical features....

Documents