freezemaster 300 series - sreweb.comsreweb.com/manual/taylor_manuals/model_336_338-339.pdf ·...

Models 336, 338 & 339

Freezemaster300 Series

Operating Instructions

036029-M6/98

Complete this page for quick reference when service is required:

Taylor Distributor:

Address:

Phone:

Service:

Parts:

Date of Installation:

Information found on the data label:

Model Number:

Serial Number:

Electrical Specs: Voltage Cycle

Phase

Maximum Fuse Size: A

Minimum Wire Ampacity: A

E June, 1998 TaylorAll rights reserved.

036029--M

Taylor Company750 N. Blackhawk Blvd.Rockton, IL 61072

The word Taylor and the Crown designare registered trademarks in the United Statesof America and certain other countries.

Table of Contents Models 336, 338 & 339

Table of Contents______________________________________________________________________________

Section 1 To the Installer 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Water Connections (Water Cooled Units Only) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . .Air Cooled Units 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Electrical Connections 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 2 To the Operator 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Compressor Warranty Disclaimer 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 3 Safety 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section 4 Operator Parts Identification 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 336 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Model 338 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Model 339 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Three Spout Door 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Accessories 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 5 Important: To the Operator 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Symbol Definitions 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power Switch 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Indicator Light - “Mix Low” 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mix Refrigeration Button 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .“Standby” 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .“Wash” 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .“Auto” 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Reset Button 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Air Tube 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Adjustable Draw Handle 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 6 Operating Procedures 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Assembly 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Sanitizing 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Priming 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Closing Procedure 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Draining Product From The Freezing Cylinder 19. . . . . . . . . . . . . . . . . . . . . . . . . . . .Rinsing 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cleaning 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disassembly 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Brush Cleaning 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Models 336, 338 & 339 Table of Contents

Section 7 Important: Operator Checklist 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .During Cleaning and Sanitizing 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Troubleshooting Bacterial Count 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Regular Maintenance Checks 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Winter Storage 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 8 Troubleshooting Guide 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section 9 Parts Replacement Schedule 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section 10 Parts List 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wiring Diagrams 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Note: Continuing research results in steady improvements; therefore, informationin this manual is subject to change without notice.

1Models 336, 338 & 339 To the Installer

031030

Section 1 To the Installer

Thesemachines are designed for indoor use only.

DONOT install themachines in an areawherea water jet could be used. Failure to follow thisinstruction may result in serious electrical shock.

Water Connections(Water Cooled Units Only)

An adequate cold water supply must be provided witha hand shut-off valve. On the underside rear of thebase pan, two 1/2” I.P.S. water connections for inletand outlet have been provided for easy hook-up. 1/2”inside diameter water lines should be connected to themachine. (Flexible lines are recommended, if localcodes permit.) Depending on local water conditions, itmay be advisable to install a water strainer to preventforeign substances from clogging the automatic watervalve. There will be only one water “in” and one water“out” connection for both single-head anddouble-headunits. DO NOT install a hand shut-off valve on thewater “out” line! Water should always flow in this order:first, through the automatic water valve; second,through the condenser; and third, through the outletfitting to an open trap drain.

Air Cooled Units

Air cooled units require a minimum of 3” (76 mm) ofclearance around all sides of the freezer to allow foradequate air flow across the condenser(s). Failure toallow adequate clearance can reduce the refrigerationcapacity of the freezer and possibly cause permanentdamage to the compressor.

Electrical Connections

Each freezer requires one power supply for each datalabel. Check the data label(s) on the freezer for fuse,circuit ampacity and electrical specifications. Refer tothewiring diagramprovided insideof theelectrical box,for proper power connections.

In the United States, this equipment is intended to beinstalled in accordance with the National ElectricalCode (NEC), ANSI/NFPA 70--1987. The purpose ofthe NEC code is the practical safeguarding of personsand property from hazards arising from the use ofelectricity. This code contains provisions considerednecessary for safety. Compliance therewith andproper maintenance will result in an installationessentially free from hazard!

In all other areas of the world, equipment should beinstalled in accordance with the existing local codes.Please contact your local authorities.

Stationary appliances which are not equipped with apower cord and a plug or other device to disconnectthe appliance from the power source must have anall--pole disconnecting device with a contact gap of atleast 3 mm installed in the external installation.

CAUTION: THIS EQUIPMENT MUST BEPROPERLY GROUNDED! FAILURE TO DO SOCAN RESULT IN SEVERE PERSONAL INJURYFROM ELECTRICAL SHOCK!

Beater rotation must be clockwise as viewed lookinginto the freezing cylinder of any model freezer.

Note: The following procedures should be performedby a trained service technician.

To correct rotation on a three-phase unit, interchangeany two incoming power supply lines at freezer mainterminal block only.

To correct rotation on a single-phase unit, change theleads inside the beater motor. (Follow diagram printedon motor.)

Electrical connections are made directly to theterminal block provided in themain control box locatedbehind the service panel.

2 Models 336, 338 & 339To the Operator

050818

Section 2 To the Operator

The freezer you have purchased has been carefullyengineered andmanufactured to give you dependableoperation. The Taylor Company soft-serve modelscovered in this manual consist of the following: 336,338 and 339.

Theseunits, whenproperly operatedandcared for, willproduce a consistent quality product. Like allmechanical products, they will require cleaning andmaintenance. A minimum amount of care andattention is necessary if the operating proceduresoutlined in this manual are followed closely.

This Operator’s Manual should be read beforeoperating or performing any maintenance on yourequipment.

Your Taylor freezer will NOT eventually compensatefor and correct any errors during the set-up or fillingoperations. Thus, the initial assembly and primingprocedures are of extreme importance. It is stronglyrecommended that personnel responsible for theequipment’s operation, both assembly anddisassembly, go through these procedures together inorder to be properly trained and to make sure that noconfusion exists.

In the event you should require technical assistance,please contact your local authorized TaylorDistributor.

If the crossed out wheeled bin symbol isaffixed to this product, it signifies that this product iscompliant with the EUDirective as well as other similarlegislation in effect after August 13, 2005. Therefore,it must be collected separately after its use iscompleted, and cannot be disposed as unsortedmunicipal waste.

The user is responsible for returning the product to theappropriate collection facility, as specified by your localcode.

For additional information regarding applicable locallaws, please contact the municipal facility and/or localdistributor.

Compressor Warranty Disclaimer

The refrigeration compressor(s) on this machine arewarranted for the term indicated on the warranty cardaccompanying this machine. However, due to theMontreal Protocol and the U.S. Clean Air ActAmendments of 1990, many new refrigerants arebeing tested and developed, thus seeking their wayinto the service industry. Some of these newrefrigerants are being advertised as drop-inreplacements for numerous applications. It should benoted that, in the event of ordinary service to thismachine’s refrigeration system, only the refrigerantspecified on the affixed data label should beused.The unauthorized use of alternate refrigerants will voidyour compressor warranty. It will be the owner’sresponsibility tomake this fact known to any technicianhe employs.

It should also be noted that Taylor does not warrant therefrigerant used in its equipment. For example, if therefrigerant is lost during the course of ordinary serviceto this machine, Taylor has no obligation to eithersupply or provide its replacement either at billable orunbillable terms. Taylor does have the obligation torecommend a suitable replacement if the originalrefrigerant is banned, obsoleted, or no longer availableduring the five year warranty of the compressor.

The Taylor Company will continue to monitor theindustry and test new alternates as they are beingdeveloped. Should a new alternate prove, through ourtesting, that it would be accepted as a drop-inreplacement, then the above disclaimer wouldbecome null and void. To find out the current status ofan alternate refrigerant as it relates to yourcompressor warranty, call the local Taylor Distributoror the Taylor Factory. Be prepared to provide theModel/Serial Number of the unit in question.

3Models 336, 338 & 339 Safety

050818

Section 3 Safety

Weat Taylor Company are concernedabout the safetyof the operator when he or she comes in contact withthe freezer and its parts. Taylor has gone to extremeefforts to design and manufacture built-in safetyfeatures to protect both youand the service technician.As an example, warning labels have been attached tothe freezer to further point out safety precautions to theoperator.

IMPORTANT -- Failure to adhere to thefollowing safety precautions may result in severepersonal injury or death. Failure to comply withthese warnings may damage the machine and itscomponents. Component damage will result inpart replacement expense and service repairexpense.

To Operate Safely:

DO NOT operate the freezer without readingthis operator’s manual. Failure to follow this instructionmay result in equipment damage, poor freezerperformance, health hazards, or personal injury.

S DO NOT operate the freezer unless it isproperly grounded.

S DO NOT attempt any repairs unless themain power supply to the freezer has beendisconnected.

S DO NOT operate the freezer with largerfuses than specified on the freezer datalabel.

Failure to follow these instructions may result inelectrocution or damage to the machine. Contact yourlocal authorized Taylor Distributor for service.

DO NOT use a water jet to clean or rinse thefreezer. Failure to follow this instruction may result inserious electrical shock.

S DO NOT allow untrained personnel tooperate this machine.

S DO NOT operate the freezer unless allservice panels and access doors arerestrained with screws.

S DO NOT remove the door, beater andblades, or drive shaft unless all controlswitches are in the OFF position.

S DO NOT put objects or fingers in doorspout.

Failure to follow these instructions may result incontaminated product or severe personal injury tofingers or hands from hazardous moving parts.

USE EXTREME CAUTION when removingthe beater assembly. The scraper blades are verysharp and may cause injury.

This freezer must be placed on a levelsurface. Failure to complymay result in personal injuryor equipment damage.

DO NOT obstruct air intake and discharge openings:3” (76 mm)minimum air space on sides and rear, and7-1/2” (191 mm) on the bottom. The Model 338requires 4-1/4” (108 mm) on the bottom.

Failure to follow this instruction may cause poorfreezer performance and damage to the machine.

These freezers are designed to operate indoors, undernormal ambient temperatures of 70_--75_F(21_--24_C). The freezers have successfully per-formed in high ambient temperatures of 104_F (40_C)at reduced capacities.

NOISE LEVEL: Airborne noise emission does notexceed 78 dB(A) when measured at a distance of 1.0meter from the surface of the machine and at a heightof 1.6 meters from the floor.

4 Models 336, 338 & 339Operator Parts Identification

Section 4 Operator Parts IdentificationModel 336

Item Description Part No.

1 Cover A.-Hopper X37963

2 Pan-Drip 17-1/4” Long 027504

3 Panel-Upper Side Left 028740

4 Orifice 022465-100

5 O-Ring 3/8 OD x .070 W 016137

6 Tube-Feed 5/32 Dia. Hole 043461-2

7 O-Ring .563 OD x .070 043758

8 Panel-Rear 029816

9 Louver-Side (Right & Left) 017471

10 Panel-Upper Side Right 028741


11 Panel A.-Lower Side (R & L) X24424

12 Adaptor A.-Caster X18915

13 Caster-Swivel 5/8 Stem 4” Wheel 018794

14 Panel-Service *336* 042824

15 Tray-Drip 16-7/8 L x 5-1/8 020157

16 Shield-Splash 022765

17 Stud-Nose 022822

18 Panel A.-Front X42821-SP1

19 Gasket-Hopper Cover-8 Qt. 037042

5Models 336, 338 & 339 Operator Parts Identification

Model 338


1 Cover A.-Hopper-Standard X38458

2 Gasket-Hopper Cover 20 Qt. 038474

3 Orifice 022465-100

4 O-Ring 3/8 OD x .070 W 016137

5 Tube A.-Feed SS 5/32 Hole X29429-2

6 O-Ring .643 OD x .077 W 018572

7 Panel-Rear 051600

8 Louver-Side (Left) 017471

9 Panel A.-Side Upper Right X48596


10 Panel-Side (Lower Right) 048487

11 Panel A.-Side Left X51596

12 Stud-Nose Cone 022822

13 Panel A.-Front X51590

14 Pan A.-Drip-15-1/8 Long X51601

15 Shield-Splash 23 Long 022766

16 Tray-Drip 22-7/8 L x 5-1/8 W 014533

17 Leg-4” SS w/O-Ring 013458

18 Skirt-Air Flow 048489


Model 339


1 Cover A.-Hopper-Standard X38458

2 Gasket-Hopper Cover 20 Qt. 038474

3 Orifice 022465-100

4 O-Ring 3/8 OD x .070 W 016137

5 Tube A.-Feed SS 5/32 Hole X29429-2

6 O-Ring .643 OD x . 077 W 018572

7 Panel-Rear 017563

8 Louver-Side (Right & Left) 017471

9 Panel-Upper Side Right 028741

10 Panel A.-Lower Side (R & L) X24424


11 Pan-Drip 17-1/4” Long 027504

12 Panel-Upper Side Left 028740

13 Stud-Nose Cone 022822

14 Panel A.-Front X32956

15 Adaptor A.-Caster X18915

16 Shield-Splash 23 L 022766

17 Tray-Drip 22-7/8 L x 5-1/8 W 014533

18 Panel-Service 024439

19 Caster-Swivel 5/8 Stem 4” Wheel 018794

7Models 336, 338 & 339 Operator Parts Identification

Three Spout Door


1 Seal-Drive Shaft 032560

2 Shaft-Beater 033235

3 Beater A.-2.8 Qt. Helicore X35466

4 Blade-Scraper-Plastic 035480

5 Bearing-Front 050216

6 Gasket-Door HT 4” Double 048926

7 O-Ring 3/8 OD x .070 W 016137

8 Plug-Prime 028805

9 Handle A.-Adj. Stainless Screw X33687

9a Handle-Adjustable 028804

9b Screw-Adjustment-Stainless 033662


9c O-Ring 1/4 OD x .070 W 015872

10 Nut-5/16-24 18-8 SS Jam 029639-BLK

11 Nut-Stud Long 034382

12 Nut-Stud Short 034383

13 Valve A.-Draw X18303

14 O-Ring 7/8 OD x .103 W 014402

15 Cap-Design 1.010” ID-6 Point 014218

16 O-Ring 5/16 OD x .070 W 016272

17 Rod A.-Pivot X20683

18 Door A.-3 Spout SH BAF W/PRG X51532-15


Accessories


1 Brush-Rear Bearing 1” x 2” 013071

2 Brush-Double Ended 013072

3 Brush-Draw Valve 1” x 2” x 17” 013073

4 Brush-White 3” x 7” 023316


5 Pail-Mix 013163

6 Lubricant-Taylor 047518

7 Sanitizer-Kay 5 (125 Packets) 041082

9Models 336, 338 & 339 Important: To the Operator

Section 5 Important: To the Operator

Item Description

1 Power Switch2 Mix Refrigeration Button3 Standby Button4 Wash Button5 Auto Button6 Indicator Light “MIX LOW”7 Reset Button

Symbol Definitions

The following chart identifies the symbol definitions used on the operator switches.

= ON

= OFF

= MIX

= WASH

= MIX LOW

= STANDBY

10 Models 336, 338 & 339Important: To the Operator

Power Switch

When placed in the “ON” position, the power switchallows SOFTECHR control panel operation.

Indicator Light - “Mix Low”

Located on the front of the machine is a mix levelindicating light. When the light is flashing, it indicatesthat themix hopper has a low supply of mix and shouldbe refilled as soon as possible. Always maintain atleast 3” (76 mm) of mix in the hopper. If you neglect toadd mix, a freeze-up may occur. This will causeeventual damage to the beater, blades, drive shaft,and freezer door.

Mix Refrigeration Button

When the mix refrigeration button is pressed, the lightcomes on indicating the mix hopper refrigerationsystem is operating. Themix refrigeration is controlledby the left side of the freezer as viewed from theoperator end. Themix refrigeration function cannot becancelled unless the “AUTO” or “STANDBY” modesare cancelled first.

“Standby”

The Separate Hopper Refrigeration System (SHR)and the Cylinder Temperature Retention System(CTR) are standard features. The SHR featureincorporates the use of a separate small refrigerationsystem to maintain the mix in the hopper below40_(4.4_C) to assure bacteria control. The CTRfeature works with the SHR to maintain a good qualityproduct. During long “No Sale” periods, it is necessaryto warm the product in the freezing cylinder toapproximately 35_F to 40_F (1.7_C to 4.4_C) toprevent overbeating and product breakdown.

To activate the SHR and CTR features, press the“STANDBY” button. Remove the air orifice and placethe air tube (end without the hole) into the mix inlethole.

When the “STANDBY” button is pressed, the lightcomes on, indicating the CTR (Cylinder TemperatureRetention System) feature has been activated. In the“STANDBY”mode, the “WASH” and “AUTO” functionsare automatically cancelled. The mix refrigerationfunction is automatically locked in to maintain the mixin the hopper.

To resumenormal operation, press the “AUTO”button.When the unit cycles off, the product in the freezingcylinder will be at serving viscosity. At this time, placethe air tube (end with the hole) into the mix inlet holeand install the air orifice.

“Wash”

When the “WASH” button is pressed, the light comeson. This indicates beater motor operation. The“STANDBY” or “AUTO” modes must be cancelled firstto activate the “WASH” mode.

Note: The Model 336 cannot be operated inthe “WASH” mode if the opposite side of the freezer isin “AUTO”. Failure to comply with this instruction willcause the rinse or sanitizing solution to freeze.

“Auto”

When the “AUTO” button is pressed, the light comeson. This indicates that the main refrigeration systemhas been activated. In the “AUTO” mode, the “WASH”or “STANDBY” functions are automatically cancelled.The mix refrigeration function is automatically lockedin to maintain the mix in the mix hopper.

Note: An indicating light and an audible tone willsound whenever a mode of operation has beenpressed. To cancel any function, press the buttonagain. The light and mode of operation will shut off.

11Models 336, 338 & 339 Important: To the Operator

Reset Button

The reset button is located in the service panel. Thereset protects the beater motor from an overloadcondition. If an overload occurs, the reset mechanismwill trip. To properly reset the freezer, press the“AUTO” button to cancel the cycle. Place the powerswitch to the “OFF” position. Press the reset buttonfirmly.

Note: Do not use metal objects to press thereset button.

Turn the power switch to the “ON” position. Press the“WASH” button and observe the freezer’sperformance. Open the side access panel. Make surethe beater motor is turning the drive shaft in aclockwise direction (from the operator end) withoutbinding.

If the beater motor is turning properly, press the“WASH” button to cancel the cycle. Press the “AUTO”button (on both sides of the unit) to resume normaloperation. If the freezer shuts down again, contact aservice technician

Air Tube

The air tube serves two purposes. One end of the tubehas a hole and the other end does not.

Figure 1

1. After priming the machine, lubricate the o-ringson the air tube (the end with the hole) andplace it into the mix inlet hole. Every time thedraw handle is raised, new mix and air from thehopper will flow down into the freezing cylinder.This will keep the freezing cylinder properlyloaded and will maintain overrun.

2. During long “No Sale” periods, remove the airorifice. Lubricate the o-rings on the air tube (theend without the hole), and place it into themix inlet hole. This will prevent any mix fromentering the freezing cylinder.

The air orifice is used to meter a certain amountof air into the freezing cylinder. The air orificemaintains overrunandallows enoughmix to enterthe freezing cylinder after a draw.

Adjustable Draw Handle

These units feature an adjustable draw handle toprovide the best portion control. The draw handleshould be adjusted to provide a flow rate of 5 to 7-1/2oz. of product per 10 seconds. To INCREASE the flowrate, turn the screw COUNTERCLOCKWISE. Turnthe screw CLOCKWISE to DECREASE the flow rate.During “Sanitizing” and “Rinsing”, the flow rate can beincreased by removing the pivot pin and placing therestrictive bar on the TOP. When drawing product,always place the restrictive bar on the bottom.

Figure 2

12 Models 336, 338 & 339Operating Procedures

Section 6 Operating Procedures

Each unit stores mix in a hopper. The mix then flowsby gravity through an air tube down into the freezingcylinder. They all have 2.8 quart (2.6 liter) capacityfreezing cylinders. All models have 20 quart (18.9 liter)mix hoppers.

Duplicate the following procedures, where they apply,for the second freezing cylinder.

We begin our instructions at the point where we enterthe store in the morning and find the partsdisassembled and laid out to air dry from the previousnight’s cleaning.

These opening procedures will show you how toassemble these parts into the freezer, sanitize them,and prime the freezer with fresh mix in preparation toserve your first portion.

If you are disassembling the machine for the first timeor need information to get to this starting point in ourinstructions, turn to page 20, “Disassembly”, and startthere.

Assembly

Note: When lubricating parts, use an approved foodgrade lubricant (example: Taylor Lube).

MAKE SURE THE CONTROL SWITCH ISIN THE “OFF” POSITION.

Step 1Install the drive shaft. Lubricate the groove and shaftportion that comes in contact with the bearing on thebeater drive shaft. Slide the seal over the shaft andgroove until it snaps into place.

DO NOT lubricate the hex end of the driveshaft. Fill the inside portion of the seal with 1/4” morelubricant and lubricate the flat side of the seal that fitsonto the rear shell bearing.

Figure 3

Insert the drive shaft into the freezing cylinder, hex endfirst, and into the rear shell bearing until the seal fitssecurely over the rear shell bearing. Engage the hexend firmly into the drive coupling. Be sure the driveshaft fits into the drive coupling without binding.

Figure 4

13Models 336, 338 & 339 Operating Procedures

Step 2Take one of the scraper blades and slip it under thehook at the front of the beater. Wrap the blade aroundthe beater following the helix and pushing the bladedown onto the helix as youwrap. At the back end of thebeater, slip the blade under the hook. Repeat thisstep for the second scraper blade.

Figure 5

Holding the beater securely, slide the beater one thirdof the way into the freezing cylinder. Looking into thefreezing cylinder, align thehole at the rear of thebeaterwith the flats on the end of the drive shaft.

Figure 6

Slide the beater the remainder of the way into thefreezing cylinder and over the end of the drive shaft.The beater should fit snugly, but not so tightly that thebeater cannot be turned slightly to engage the driveshaft. If the beater slides in too easily with little or noresistance, there will not be enough force against thebeater to hold the blades in place. If this is the case,contact your authorized Taylor service agent.

Repeat Steps 1 and 2 for the other side of the freezer.

Step 3Assemble the freezer door. Place the large rubbergaskets into the grooves on the back side of thefreezer door.

Slide the white plastic front bearings over the bafflerods onto the bearing hubs making certain that theflangedendof thebearing is resting against the freezerdoor.

DO NOT LUBRICATE THE GASKETS ORTHE FRONT BEARINGS. Damage to componentsmay occur.

Figure 7

Slide the two o-rings into the grooves on the primeplugs. Apply an even coat of Taylor Lube to the o-ringsand shafts.

Figure 8


Insert the prime plugs into the holes in the top of thefreezer door, and push down.

Figure 9

Step 4Install the freezer door. Insert the baffle rods throughthe opening in the beaters and seat the door flush withthe freezing cylinder. With the door seated on thefreezer studs, install the handscrews. Tighten equallyin a crisscross pattern to insure the door is snug.

Note:Theshort handscrews goon thebottomand the long handscrews go on top.

Figure 10

Step 5Install the three draw valves. Slide the two o-rings intothe grooves on the draw valves, and lubricate.

Figure 11

Lubricate the inside of the freezer door spouts, top andbottom, and insert the draw valves from the bottomuntil the slot in the draw valves comes into view.

Figure 12

Step 6Install the adjustable draw handles. Slide the o-ringinto the groove on the pivot pin, and lubricate.

Figure 13


Slide the fork over the bar in the slot of the draw valve.Secure with pivot pin.

Note: The Models 336, 338 and 339 have three drawhandles. Slide the fork of the draw handle in the slot ofthe draw valve, starting from the right. Slide the pivotpin through each draw handle as you insert them intothe draw valves.

Figure 14

Note: These units feature adjustable draw handles toprovide the best portion control. The draw handles canbe adjusted for different flow rates. See page 11 formore information on adjusting these handles.

Step 7Snap the design caps over the end of the door spouts.

Figure 15

Step 8Install the front drip tray and the splash shield underthe door spouts.

Figure 16

Step 9Slide the rear drip pan into the hole in the side panel(front panel on a Model 338).

Figure 17

Step 10Slide two o-rings on one end of the air tube. Slide twoo-rings on the other end of the air tube.

Figure 18


Slide the small o-ring into the groove of the air orifice.Do not lubricate the o-ring.

Figure 19

Note: Make sure the hole in the air orifice is clean andis not clogged. If the hole in the air orifice shouldbecome clogged, use soap and hot water to clear thehole.

Do not enlarge the hole in the air orifice.

Install the air orifice into the hole in the top of the airtube (in the end without the small hole on the side).

Figure 20

Step 11Lay the air tube (with the air orifice installed) and thehopper gasket in the bottom of the mix hopper forsanitizing.

Repeat Steps 10 and 11 for the other side of thefreezer.

Sanitizing

Step 1Prepare two gallons (7.6 liters) of an approved 100PPM sanitizing solution (example: Kay-5R). USEWARMWATER ANDFOLLOW THEMANUFACTUR-ER’S SPECIFICATIONS.

Step 2Pour the two gallons (7.6 liters) of sanitizing solutioninto the hopper and allow it to flow into the freezingcylinder.

Figure 21

Step 3While the solution is flowing into the freezing cylinder,brush clean the mix hopper. When cleaning thehopper, take particular care in brushing the mix levelsensing probe on the rear wall of the hopper, the mixinlet hole, the air tube, and the hopper gasket.

Figure 22


Figure 23

Step 4Place the power switch in the “ON” position.

Figure 24

Step 5Press the “WASH” button. This will cause thesanitizing solution in the freezing cylinder to agitate.Allow it to agitate for five minutes.

Figure 25

Step 6Place an empty pail beneath the door spout and raisethe prime plug.

Figure 26

Step 7When a steady stream of sanitizing solution is flowingfrom the prime plug opening in the bottom of thefreezer door, lower the draw handle. Draw off all thesanitizing solution.

Figure 27

Note: Momentarily pull the center draw handle downto sanitize the center door spout.

Step 8Once the sanitizer stops flowing from the door spout,raise the draw handle and press the “WASH” button,cancelling the beater motor operation.

Note: You have just sanitized the freezer. Besure your hands are sanitized before continuingthese instructions.


Step 9Assemble the hopper gasket around the top edge ofthe mix hopper. Stand the air tube in the corner of thehopper.

Figure 28

Repeat Steps 1 through 9 for the other side of thefreezer.

Priming

Step 1With a pail beneath the door spout, lower the drawhandle. Be sure the prime plug is still in the UPposition. Pour two gallons (7.6 liters) of fresh mix intothe mix hopper and allow it to flow into the freezingcylinder. This will force out any remaining sanitizingsolution. When full strength mix is flowing from thedoor spout, raise the draw handle.

Note: Use only fresh mix when priming the freezingcylinder.

Figure 29

Step 2Once a steady stream of mix starts to flow from theprime plug opening in the bottom of the freezer door,push down the prime plug.

Figure 30

Step 3Lubricate the o-rings on theair tubeon theendwith thesmall hole on the side.

Step 4Install the air tube in the “AUTO” position.

Figure 31


Step 5Press the “AUTO” button. The “AUTO” light will comeon indicating the main refrigeration system isoperating. When the unit cycles off, the product will beat serving viscosity.

Figure 32

Note: The mix refrigeration light will come on,indicating the mix refrigeration system is operating tomaintain the mix in the mix hopper.

Step 6Fill the hopper with mix. As the mix level comes incontact with the mix level sensing probe on the rearwall of the hopper, the “MIX LOW” light will shut off.

Step 7Place the mix hopper cover in position over the mixhopper.


Closing Procedure

To disassemble your unit, the following items will beneeded:

S Two cleaning pails

S Sanitized stainless steel rerun can with lid

S Necessary brushes (provided with freezer)

S Cleaner

S Single service towels

Draining Product From theFreezing CylinderStep 1Press the “AUTO” button, cancelling compressor andbeater motor operation.

Press the mix refrigeration button, cancelling the mixhopper refrigeration system.

Step 2Remove the hopper cover, hopper gasket and air tube.Take these parts to the sink for cleaning.

Step 3With a sanitized pail beneath the door spout, press the“WASH” button. Lower the draw handle and drain theremaining product from the freezing cylinder and themix hopper.

Step 4When the flow of product stops, press the “WASH”button, and raise the draw handle. If local health codespermit, empty the rerun into a sanitized stainless steelcan. Cover the container and place it in the walk-incooler.


Note: For the Model 336, both sides must be inWASH. If one side is in AUTO and the other is inWASH, the side that is inWASHwill continue to freeze.

ALWAYS FOLLOW LOCAL HEALTH CODES.

RinsingStep 1Pour twogallons (7.6 liters) of cool cleanwater into themix hopper. With the brushes provided, scrub the mixhopper, mix inlet hole and mix level sensing probe.

Step 2With apail beneath thedoor spout, raise theprimeplugand press the “WASH” button.

Step 3When a steady stream of rinse water is flowing fromthe prime plug opening in the bottom of the freezerdoor, lower the draw handle. Drain all the rinse waterfrom the freezing cylinder, raise the draw handle andpress the “WASH” button, cancelling the “WASH”mode.



CleaningStep 1Prepare two gallons (7.6 liters) of an approved clean-ing solution (example: Kay-5R). USE WARMWATERAND FOLLOW THE MANUFACTURER’S SPECIFI-CATIONS.

Step 2Push down the prime plug. Pour the two gallons (7.6liters) of cleaning solution into the mix hopper.

Step 3While the solution is flowing into the freezing cylinder,brush clean the mix hopper, mix level sensing probe,and the mix inlet hole.

Step 4Press the “WASH” button. This will cause the cleaningsolution in the freezing cylinder to agitate.

Step 5Place an empty pail beneath the door spout and raisethe prime plug.

Step 6When a steady stream of cleaning solution is flowingfrom the prime plug opening in the bottom of thefreezer door, lower the draw handle. Draw off all of thesolution.

Step 7Once the cleaner stops flowing from the door spout,raise the draw handle and press the “WASH” button,cancelling the “WASH” mode.


DisassemblyStep 1

BE SURE THE POWER SWITCH IS IN THE“OFF” POSITION. MAKE SURE NO LIGHTS ARELIT ON THE CONTROL PANEL.

Step 2Remove the handscrews, freezer door, beaters,scraper blades, and drive shafts from the freezingcylinders. Take these parts to the sink for cleaning.

Step 3Remove the front drip tray and the splash shield.

Brush Cleaning

Step 1Prepare a sink with an approved cleaning solution(example: Kay-5R). USE WARM WATER ANDFOLLOW THE MANUFACTURER’S SPECIFI-CATIONS. If another approved cleaner is used, diluteit according to the label instructions. (IMPORTANT:Follow the label directions. Too STRONG of a solutioncan cause parts damage, while too MILD of a solutionwill not provide adequate cleaning.) Make sure allbrushes provided with the freezer are available forbrush cleaning.

Step 2Remove the seals from the drive shafts.

Step 3From the freezer door remove:

S gasketsS front bearingsS pivot pinsS adjustable draw handlesS design capsS draw valvesS prime plugs

Remove all o-rings.

Note: To remove o-rings, usea single service towel tograsp theo-ring. Apply pressure in an upwarddirectionuntil the o-ring pops out of its groove. With the otherhand, push the top of the o-ring forward and it will rollout of the groove and can be easily removed. If thereis more than one o-ring to be removed, always removethe rear o-ring first. This will allow the o-ring to slideover the forward rings without falling into the opengrooves.


Step 4Remove the o-rings from the air tubes and air orifices.

Step 5Return to the freezer with a small amount of cleaningsolution. Brush clean the rear shell bearings at theback of the freezing cylinders with the black bristlebrush.

Figure 33

Step 6Remove the rear drip pan and take it to the sink forcleaning.

Note: If the drip pan is filled with an excessive amountof mix, refer to the Troubleshooting Guide.

Step 7Thoroughly brush clean all disassembled parts in thecleaning solutionmaking sure all lubricant and mix filmis removed. Take particular care to brush clean thedraw valve cores in the freezer door. Place all thecleaned parts on a clean, dry surface to air dryovernight.

Step 8Wipe clean all exterior surfaces of the freezer.

22 Models 336, 338 & 339Important: Operator Checklist

Section 7 Important: Operator Checklist

During Cleaning and Sanitizing

Cleaning and sanitizing schedules are governed byyour State or local regulatory agencies and must befollowed accordingly. The following check pointsshould be stressed during the cleaning and sanitizingoperations.

WE RECOMMEND DAILY CLEANING ANDSANITIZING.

ALWAYS FOLLOW LOCAL HEALTH CODES.

Troubleshooting Bacterial Count

j 1. Thoroughly clean and sanitize machineregularly, including complete disassembly andbrush cleaning.

j 2. Use all brushes supplied for thorough cleaning.The brushes are specially designed to reach allmix passageways.

j 3. Use the white bristle brush to clean the mix inlethole which extends from the mix hopper downto the rear of the freezing cylinder.

j 4. Use the black bristle brush to thoroughly cleanthe rear shell bearing located at the rear of thefreezing cylinder. Be sure to have a generousamount of cleaning solution on the brush.

j 5. IF LOCAL HEALTH CODES PERMIT THEUSE OF RERUN, make sure the mix rerun isstored in a sanitized, covered stainless steelcontainer and used the following day. DO NOTprime the machine with rerun. When usingrerun, skim off the foam and discard. Mix thererunwith freshmix in a ratio of 50/50 during thedays operation.

j 6. On a designated day of theweek, run themix aslow as feasible and discard it after closing. Thiswill break the rerun cycle and reduce thepossibility of high bacteria and coliform counts.

j 7. Properly prepare the cleaning and sanitizingsolutions. Read and follow label directionscarefully. Too strong of a solution may damagethe parts and too weak of a solution will not doan adequate job of cleaning or sanitizing.

j 8. The temperature of the mix in the mix hopperand walk-in cooler should be below 40_F.(4.4_C.).

Regular Maintenance Checks

j 1. Replace scraper blades that are nicked ordamaged. Before installing the beaterassembly, be certain that scraper blades areproperly attached to the helix.

j 2. Check the rear shell bearing for signs of wear(excessive mix leakage in rear drip pan) and becertain it is properly cleaned.

j 3. Using a screwdriver and cloth towel, keep therear shell bearing and the female hex drivesocket clean and free of lubricant and mixdeposits.

j 4. Dispose of o-rings and seals if they are worn,torn, or fit too loosely, and replace with newones.

j 5. Follow all lubricating procedures as outlined in“Assembly”.

j 6. If your machine is air cooled, check thecondensers for accumulation of dirt and lint.Dirty condensers will reduce the efficiency andcapacity of themachine. Condensers should becleaned monthly with a soft brush. Never usescrewdrivers or other metal probes to cleanbetween the fins.

Caution: Always disconnect electri-cal power prior to cleaning the condenser.

23Models 336, 338 & 339 Important: Operator Checklist

j 7. If your machine is equipped with an auxiliaryrefrigeration system, check the auxiliarycondenser for accumulation of dirt and lint. Dirtycondensers will reduce the refrigerationcapacity of the mix hopper. Condensers mustbe cleaned monthly with a soft brush. Neveruse screwdrivers or other metal probes to cleanbetween the fins.

Caution: Always disconnectelectrical power prior to cleaning thecondenser.

j 8. If yourmachine iswater cooled, check thewaterlines for kinks or leaks. Kinks can occur whenthe machine is moved back and forth forcleaning or maintenance purposes.Deteriorated or cracked water lines should bereplaced only by an authorized Taylordistributor.

Winter StorageIf the placeof business is to be closedduring thewintermonths, it is important to protect the freezer byfollowing certain precautions, particularly if thebuilding is subject to freezing conditions.Disconnect the freezer from the main power source toprevent possible electrical damage.

On water cooled freezers, disconnect the watersupply. Relieve pressure on the spring in the watervalve. Use air pressure on the outlet side to blow outany water remaining in the condenser, and then add aliberal amount of permanent type auto anti-freeze.This is extremely important. Failure to follow thisproceduremay cause severe and costlydamage to therefrigeration system.

Your local Taylor Distributor can perform this winterstorage service for you.

Wrap detachable parts of the freezer such as beater,blades, drive shaft, and freezer door, and place theminaprotecteddry place. Rubber trimparts andgasketscan be protected by wrapping them withmoisture-proof paper. All parts should be thoroughlycleaned of dried mix or lubrication which attract miceand other vermin.

24 Models 336, 338 & 339Troubleshooting Guide

Section 8 Troubleshooting Guide

PROBLEM PROBABLE CAUSE REMEDY PAGEREF.

1. No product is beingdispensed with draw valveopen and the machine inthe “AUTO” mode.

a. Freeze-up in mix inlethole.

a. Call service technician toadjust the mix hoppertemperature.

------

b. Beater motor out on reset. b. Reset the freezer. 11

c. The beater is rotatingcounterclockwise from theoperator end.

c. Contact service technicianto correct rotation toclockwise from operatorend.

------

d. The circuit breaker is offor the fuse is blown.

d. Turn the breaker on, orreplace the fuse.

------

e. There is inadequate mix inthe mix hopper.

e. Fill the mix hopper withmix.

19

f. The air orifice is notinstalled.

f. Install air orifice in airtube.

18

g. Air tube is installed in the“STANDBY” position.

g. Install the air tube in the“AUTO” position.

18

2. The product is too stiff. a. The viscosity needsadjustment.

a. Contact servicetechnician.

------

b. The air orifice is notinstalled.

b. Install air orifice in airtube.

18

3. The product is too soft. a. Viscosity needsadjustment.

a. Contact servicetechnician.

------

b. Not enough air spacearound unit. (Air cooledunits)

b. Allow for adequate air flowacross the condenser.

1

c. Worn scraper blades. c. Replace regularly. 27

d. Dirty condenser (A/C) d. Clean monthly. 22

e. Mix is out of date. e. Use only fresh mix. ------

f. Loss of water. (W/C) f. Locate cause of waterloss and correct.

23

g. Loss of refrigerant. g. Call a service technician. ------

4. The mix in the mix hopperis too cold.

a. The temperature is out ofadjustment.


------

25Models 336, 338 & 339 Troubleshooting Guide


5. The mix in the mix hopperis too warm.

a. The temperature is out ofadjustment.


------

b. Missing or defective mixhopper gasket.

b. Replace/install the gasketaround the mix hopper.

18

c. The mix hopper cover isnot in position.

c. Place the cover inposition.

19

d. The mix refrigeration lightis not lit.

d. Press mix refrigerationbutton.

19

e. The condenser is dirty. e. Clean the condenser. 22

6. The drive shaft is stuck inthe drive coupling.

a. Rounded corners of driveshaft, coupling, or both.

a. Call service technician tocorrect cause, and toreplace the necessarycomponents. Do notlubricate the hex end ofthe drive shaft.

------

b. Mix and lubricant collectedin the drive coupling.

b. Brush clean the rear shellbearing area regularly.

21

7. The freezing cylinder wallsare scored.

a. The beater assembly isbent.

a. Call service technician torepair or replace thebeater and to correct thecause of insufficient mixin the freezing cylinder.

------

b. The front bearing ismissing or worn on thefreezer door.

b. Install or replace the frontbearing.

13

8. Excessive mix leakageinto the rear drip pan.

a. Missing or worn driveshaft seal on drive shaft.

a. Install or replace regularly. 12 / 27

b. The rear shell bearing isworn.

b. Call service technician toreplace rear shell bearing.

------

9. Excessive mix leakagefrom door spout.

a. Missing or worn drawvalve o-rings.

a. Install or replace regularly. 14 / 27

b. Inadequate lubrication ofdraw valve o-rings.

b. Lubricate properly. 14

c. Wrong type of lubricant isbeing used (example:petroleum base lubricant).

c. Use the proper lubricant(example: Taylor Lube).

12

26 Models 336, 338 & 339Troubleshooting Guide


10. No freezer operation afterpressing the “AUTO”button.

a. Unit is unplugged. a. Plug into wall receptacle. ------

b. The circuit breaker is offor the fuse is blown.

b. Turn the breaker on, orreplace the fuse.

------

c. The beater motor is out onreset.

c. Reset the freezer. 11

d. The unit has gone off onhigh pressure cut-out.

d. Allow the unit to cool andreset. Check for dirtycondenser (air cooled) orloss of water (watercooled).

22/ 23

11. Product is not feeding intothe freezing cylinder.

a. Inadequate level of mix inthe mix hopper.

a. Fill the mix hopper withmix.

19

b. The mix inlet hole isfrozen up.

b. The mix hoppertemperature needsadjustment. Call servicetechnician.

------

c. The air tube is installedincorrectly.

c. Install the air tube in themix inlet hole, using theend with the small hole inthe side.

18

d. The air orifice is notinstalled.

d. Install the air orifice in theair tube.

18

27Models 336, 338 & 339 Parts Replacement Schedule

Section 9 Parts Replacement Schedule

PART DESCRIPTION EVERY 3 MONTHS EVERY 6 MONTHS ANNUALLY

Drive Shaft Seal X

Scraper Blade X

Freezer Door Gasket X

Front Bearing X

Draw Valve O-Ring X

Pivot Pin O-Ring X

Prime Plug O-Ring X

Air Tube O-Ring X

Air Orifice O-Ring X

White Bristle Brush, 3” x 7” Inspect & Replaceif Necessary

Minimum

White Bristle Brush, 1” x 2” Inspect & Replaceif Necessary

Minimum

Black Bristle Brush, 1” x 2” Inspect & Replaceif Necessary

Minimum

Double-Ended Brush Inspect & Replaceif Necessary

Minimum

Section 10 Parts List

+ Available Separately

28Parts List Models 336, 338 & 339

DESCRIPTION

PART

NUMBER

336

QTY.

338

QTY.

339

QTY.

WARR.

CLASS

REMARKS

PARTS

UPDATE

ACCUMULATO

R--C

OPPER2”DIA

10”

047062

1103

ADAPTO

RA.--CASTER

X18915

44

103

BEARING--FRONT

050216

22

2000

BEARING--R

EARSHELL

*NICK.PLATE

031324

22

2000

+GUIDE--D

RIP

SEAL

028992

22

2000

+NUT--BRASSBEARING

028991

22

2000

+WASHER--BEARINGLO

CK

012864

22

2000

BEATERA.--2.8Q

T--H

ELICORE

X35466

22

2103

+BLA

DE--SCRAPER--PLA

STIC

13--1/4L

035480

44

4000

BELT--AX33

024396

4000

BELT--AX35

022848

4000

BELT--AX38

023873

4000

BLO

CK--TERMINAL2P

039422

11

2103

BLO

CK--TERMINAL5POLE

024329

1103

BLO

WERA.

X46573--

1103

BOOT--C

APACITORINSULATING

031314

1000

CAPACITOR--R

UN--10

UF/370V

033047

1103

HOUSINGA.--W/W

HEEL

X30160

1103

MOTO

R--BLO

WER--208/230V50/60HZ

046536--

1103

BLO

WERA.

X47833--

1103

BOOT--C

APACITORINSULATING

031314

1000

CAPACITOR--R

UN--10

UF/370V

033047

1103

HOUSINGA.--W/W

HEEL

X30160

1103

MOTO

R--BLO

WER--208/230V50/60HZ

046536--

1103

SCREEN--BLO

WER*X30153*

030158

1103

CLIP

030159

4103

BOARD--LOGIC--G

EN2.6W/SELDIFF

X36641S

ER1

22

2212

BOARD--POWER--G

EN1&2

X32326--SER

22

2212

BRUSH--D

OUBLE

ENDED--PUMP&FEEDTUBE

013072

11

1000

BRUSH--D

RAW

VALVE1”ODX2”X17”L

013073

11

1000

BRUSH--M

IXPUMPBODY--3”X7”WHITE

023316

11

1000

BRUSH--R

EARBRG1IN.DX2IN.LGX14

013071

11

1000

CABLE

A.--2COND--24IN--PUSHON

X34464

11

103

CABLE

--RIBBON--14C

--30”L--DIP/DIL

035683

1103

29


Models 336, 338 & 339 Parts List

DESCRIPTION

PARTS

UPDATE

REMARKS

WARR.

CLASS

339

QTY.

338

QTY.

336

QTY.

PART

NUMBER

CABLE

--RIBBON--14C

--40”L--DIP/DIL

042931

1103

CABLE

--RIBBON--PWR/RELAY--60IN

032445

22

103

CAP--D

ESIGN--1.010”ID--6

POINT

014218

33

3000

CASTER--SWV5/8STEM4INWHEEL

018794

44

103

COMPRESSORL63A

113B

BCA

048259--

1512

MAIN

+CAPACITOR--R

UN--20UF/440V

012906

1103

208--230/60/1

+CAPACITOR--STA

RT--161--193UF/250V

031790

1103

208--230/60/1

+RELAY--STA

RT--C

OMPRESSOR

038145

1103

208--230/60/1

COMPRESSORAHA2490ZXD--AH556E

T047519--

1512

MAIN

+RELAY--STA

RT--C

OMPRESSOR

036047

1103

208--230/60/1

+CAPACITOR--STA

RT--135--155UF/33

036048

1103

208--230/60/1

+CAPACITOR--R

UN--35UF/440V

048132

1103

208--230/60/1

COMPRESSOR--M

65B163B

BCA

048258--

2512

MAIN

+CAPACITOR--STA

RT--161--193UF/250V

031790

2103

208--230/60/1

+RELAY--STA

RT--C

OMPRESSOR

037430

2103

208--230/60/1

+CAPACITOR--R

UN--25

UF/440V

037431

2103

208--230/60/1

COMPRESSORTL3G--R

134A

047701--

11

1512

SHR

CAPACITOR--STA

RT--60U

F--220/275V

047703

11

1103

208--230/60/1

+KIT--M

OUNTING--C

OMPRESSOR

047704

11

1103

+RELAY--STA

RT--C

OMPRESSOR--TL3G

047702--

11

1103

208--230/60/1

+COVER--TERMINAL

047739

11

1103

CONDENSER--AC--12LX18HX2.6T--3ROW

048233

12

103

CONDENSER--AC--19X

14X2.5--4ROW

048623

1103

CONDENSER--AC--7X6X

1.25--2

ROW

027155

11

1103

SHR

COUPLING--D

RIVE3/4HEXX1--7/8

012721

22

2103

+SCREW--5/16--18X5/16

ALLENSET

042511

44

4000

COVERA.--HOPPER*162--168*

X37963

1103

+GASKET--H

OPPERCOVER--8QT

037042

1000

+KNOB--M

IXCOVER

025429

1103

COVERA.--HOPPER--STD

X38458

22

103

+GASKET--H

OPPERCOVER--20QT--TWIN

038474

11

000

+KNOB--M

IXCOVER

025429

22

103

DECAL--CLE

ANINST.--H

OPPER

019029

11

1000

DECAL--DEC--336SOFTECH

038337

1000

DECAL--DEC--TWIN--SS

032919

11

000



DESCRIPTION

PARTS

UPDATE

REMARKS

WARR.

CLASS

339

QTY.

338

QTY.

336

QTY.

PART

NUMBER

DECAL--POWERSWITCH

032484

11

1000

DECAL--TROUBLE

SHOOTING

038374

11

1000

DEFLE

CTO

R--BLO

WEREXHAUST

048345

1103

DEFLE

CTO

R--BLO

WEREXHAUST

046586

1103

DIAGRAM--W

IRING

038333

1000

DIAGRAM--W

IRING

051624--

1000

DIAGRAM--W

IRING

046585--

1000

DOORA.--3SPOUT

X51532--15

11

1103

+HANDLE

A.--DRAW--ADJ.--STA

INLE

SS

X33687

33

3103

+HANDLE

--ADJU

STA

BLE

028804

33

3103

+O--R

ING--1/4ODX.070W

50DURO

015872

33

3000

+SCREW--ADJU

STMENT

026592

33

3000

+PLU

G--PRIME

028805

22

2103

+O--R

ING--3/8ODX.070W

016137

44

4000

+RODA.--PIVOT

X20683

11

1103

+O--R

ING--5/16ODX.070W

016272

11

1000

+VALVEA.--DRAW

X18303

33

3103

+O--R

ING--7/8ODX.103W

014402

66

6000

DRYER--C

AP.TUBE--H

P62/R134A

047699

11

1000

SHR

DRYER--FILTER--H

P62--3/8X1/4S

047521

12

000

DRYER--FILTER--H

P62--3/8X1/4S

048901

1000

EYELE

T--R

ESETBUTTO

N013739

22

000

FASTENER--C

LIP1/4--20U--TYPE

045865

88

8000

BASEPAN/PANELS

GASKET--D

OORHT4”--D

OUBLE

048926

22

2000

GEARA.*REDUCER

021286

22

2212

GUARD--FAN

028534--1

1103

GUIDEA.--DRIP

PAN

X51567

1103

GUIDEA.--DRIP

PAN

X27554

1103

GUIDEA.--DRIP

PAN

X28699

1103

HOOD

041026

1103

HOOD

042866

1103

HOOD

035434

1103

KITA.--TUNEUP--3

SPOUT--N

ONHT

X49463--6

1000

BEARING--FRONT

050216

2000

CAP--D

ESIGN--1.010”ID--6

POINT

014218

3000

31



DESCRIPTION

PARTS

UPDATE

REMARKS

WARR.

CLASS

339

QTY.

338

QTY.

336

QTY.

PART

NUMBER

GASKET--D

OORHT4”--D

OUBLE

048926

2000

O--R

ING--.563ODX.070W--#013

043758

8000

O--R

ING--3/8ODX.070W

016137

6000

O--R

ING--5/16ODX.070W

016272

1000

O--R

ING--7/8ODX.BW

014402

7000

SEAL--DRAW

VALVE

034698

1000

SEAL--DRIVESHAFT

032560

2000

TOOL--CLE

ANING0--RINGREMOVAL

048260

1000

KITA.--TUNEUP--3

SPOUT--N

ONHT

X49463--4

11

000

BEARING--FRONT

050216

22

000

CAP--D

ESIGN--1.010”ID--6

POINT

014218

33

000

GASKET--D

OORHT4”--D

OUBLE

048926

22

000

O--R

ING--.643ODX.077W

018572

88

000

O--R

ING--3/8ODX.070W

016137

66

000

O--R

ING--5/16ODX.070W

016272

11

000

O--R

ING--7/8ODX.103W

014402

77

000

SEAL--DRAW

VALVE

034698

11

000

SEAL--DRIVESHAFT

032560

22

000

TOOL--CLE

ANING0--RINGREMOVAL

048260

11

000

LABEL--DOORCAUTION

032749

11

1000

LABEL--M

OVINGPARTSWARN

024315

33

3000

LABEL--W

ARNINGPANEL

036529

33

3000

LEG--4”SS--W

/ORING

013458

4103

LOUVER--SIDE

017471

21

2103

MODEL338--LE

FTSIDE

LUBRICANT--TAYLO

R4OZ.

047518

11

1000

MAN--O

PER

300SERIESSOFTECH

036029--M

11

1000

MOTO

R--1.0HP

013102--

22

2212

MOTO

R--FAN80

W208/230V

60HZ

051744--

1103

MAIN

SYSTEM

+CAPACITOR--R

UN--4U

F--440V

051785

1103

+FAN--5

BLA

DE12”PUSH32DEGCC

047279

1103

MOTO

R--FAN105C

FM3000RPM

027309--

11

1103

SHR

NUT--STUD*460--664--754--56*LO

NG

034382

22

2103

NUT--STUD*460--664--754--56*SHORT

034383

22

2103

ORIFICE

022465--100

22

2103

+O--R

ING--3/8ODX.070W

016137

22

2000



DESCRIPTION

PARTS

UPDATE

REMARKS

WARR.

CLASS

339

QTY.

338

QTY.

336

QTY.

PART

NUMBER

PAIL--M

IX6QT.

023348

1000

PAIL--M

IX10

QT.

013163

11

000

PANA.--DRIP

--17--1/4”LO

NG

027504

11

103

SIDEPANELMOUNT

PANA.--DRIP

--15--1/8”LO

NG

X51601

1103

FRONTPANELMOUNT

PANA.--DRIP

HINGED

X41844

1103

INTERNALMOUNT

PANELA.--FRONT

X42821--SP1

1103

PANELA.--FRONT

X51590

1103

PANELA.--FRONT

X32956

1103

PANELA.--LO

WERSIDE

X24424

22

103

RIGHT&LE

FT

PANELA.--SIDELE

FT

X51596

1103

PANELA.--SIDERIGHT

X48596

1103

UPPER

PANEL--SIDE--R

IGHT

048487

1103

LOWER

PANEL--REAR

029816

1103

PANEL--REAR

017563

1103

PANEL--REAR

051600

1103

PANEL--SERVICE

042824

1103

PANEL--SERVICE

024439

1103

PANEL--UPPERSIDELE

FT

028740

11

103

PANEL--UPPERSIDERIGHT

028741

11

103

PLATE--D

EC--336*

038081

1103

PLATE--D

EC--754--755

032961

11

103

PLU

G--D

RIP

TRAYHOLE

029595

11

000

PROBEA.--MIX

*SQUARE*

X30922

22

2103

PROBEA.--THERMISTO

RX31602

22

2103

BARREL

PROBEA.--THERMISTO

RX34466

1103

HOPPER

PROBEA.--THERMISTO

R/RESISTO

RX50717

11

103

HOPPER

PULLEY--2AK20

X5/8BORE

034238

22

2103

BEATERMOTO

R

PULLEY--2AK64--5/8BORE

039695

22

2103

GEAR

RECEPTA

CLE

A.--QUICKCONNECT

X33321

22

103

DRAW

SWITCH

RELAY--3

POLE

--20A

--208/240

50/60

012725--

11

2103

COMPRESSOR

RELAY--SPDT--30A--240

V032607--

11

103

BLO

WERMOTO

R

SANITIZERKAY--5

125PACKETS

041082

11

1000

SHAFT--BEATER

033235

22

2103

+SEAL--DRIVESHAFT

032560

22

2000

SHELL

A.--INSULATED

X37091--SP

1512

33



DESCRIPTION

PARTS

UPDATE

REMARKS

WARR.

CLASS

339

QTY.

338

QTY.

336

QTY.

PART

NUMBER

+STUD--N

OSECONE

022822

4103

SHELL

A.--INSULATED

X50770

11

512

+STUD--N

OSECONE

022822

44

103

SHIELD

--SPLA

SH23

L022766

11

1103

SKIRT--AIR

FLO

W048489

1103

+COLLAR--H

OLD

ING

019481

3103

+SCREW--H

OLD

INGCOLLAR(10--32x3/4OVAL)

001086

3000

STA

RTER

041950--

22

2103

SWITCHA.--DRAW

*336*SELF

CLO

SE

X43417--SER

1103

ARM--SWITCH--D

RAW--LEFT

038649

1103

ARM--SWITCH--D

RAW--R

IGHT

038650

1103

BRACKETA.--SPRINGRETURN

X38257

1103

E--R

ING1/4

032190

4000

PIN--PIVOT--D

RAW

SWITCH

038484

1103

SPRING--EXTENSION.375X.045X1.00

038922

2103

SPRING--R

ETURN--LEFT--TWIN

TWIST

038923

1103

SPRING--R

ETURN--R

IGHT--TWIN

TWIST

038924

1103

SWITCHA.--DRAW--TWIN

TWIST

X39269

1103

BRACKET--D

RAW

SWITCH--TWIN

TWIST

039264

1103

SWITCH--LEVER--SPDT--11A

--125--277V

039252

2103

SWITCHA.--DRAW

*SELF

CLO

SING*

X38547

11

103

ARM--SWITCH--D

RAW--LEFT

038649

11

103

ARM--SWITCH--D

RAW--R

IGHT

038650

11

103

BRACKETA.--SPRINGRETURN

X38257

11

103

BRACKETA.--SWITCH*338--39--754

X38252

11

103

E--R

ING1/4

032190

44

000

PIN--PIVOT--D

RAW

SWITCH

038484

11

103

ROD--SPRINGRETA

INER

038254

11

103

SCREW--8--32X

3/8HEXHDTYPE23

039267

22

000

SPRING--EXTENSION.375X.045X1.00

038922

22

103

SPRING--R

ETURN--LEFT--TWIN

TWIST

038923

11

103

SPRING--R

ETURN--R

IGHT--TWIN

TWIST

038924

11

103

SWITCHA.--DRAW--TWIN

TWIST

X39269

11

103

BRACKET--D

RAW

SWITCH--TWIN

TWIST

039264

11

103

SCREW--4--40X1/2”TA

PTITEPANHD

042604

44

000



DESCRIPTION

PARTS

UPDATE

REMARKS

WARR.

CLASS

339

QTY.

338

QTY.

336

QTY.

PART

NUMBER

SWITCH--LEVER--SPDT--11A

--125--277V

039252

22

103

SWITCH--PRESSURE440PSI--SOLD

ER

048230

11

2103

SWITCH--TOGGLE

--4PDT*ON--N

ONE--O

N037394

11

1103

TRAY--D

RIP

16--7/8LX5--1/8

020157

1103

TRAY--D

RIP

22--7/8LX5--1/8W

014533

11

103

TRIM--FRONT

051595

1103

TRIM--R

EARCORNERLE

FT

013761

11

103

TRIM--R

EARCORNERLE

FT

044280

1103

TRIM--R

EARCORNERRIGHT

013663

11

103

TRIM--R

EARCORNERRIGHT

044281

1103

TUBE--FEED5/32

DIA.H

OLE

043461--2

2103

+O--R

ING--.563ODX.070W--#013

043758

8000

TUBEA.--FEED--SS--5/32HOLE

DIA

X29429--2

22

103

+O--R

ING--.643ODX.077W

018572

88

000

VALVE--ACCESS1/4X3/8SOLD

ER

029406

11

103

VALVE--ACCESS1/4FLX1/4S

OLD

ER

044404

11

1103

VALVE--ACCESS1/4FLX3/8S

OLD

ER

043232

12

103

VALVE--ACCESS--1/4MFLX

1/4S--90

047016

12

2103

VALVE--EPR1/4S

022665

11

1103

VALVE--EXP--AUTO

--1/4SX1/4FPT

046365

22

103

VALVE--EXP--AUTO

--1/4SX1/4FPT

047232

2103

VALVE--SOLE

NOID

7/16

ORF5/8O

DF

048626--

22

103

VALVE--SOLE

NOID

7/64ORFX1/4S

043449--

22

103

VIDEO--TRAIN

FILM--SS--SOFTECH

038047--V

11

1000

WASHER--PLA

STIC

PIVOT

013808

44

000

WATERCOOLED

BLO

WER--100

CFM

012796--

11

103

CONDENSER--W

/CCOAX

047540

1103

CONDENSER--W

C--SPIRAL11--1/2

049309

1103

CONDENSER--W

/CCOAX

048287

2103

GUARD--BLO

WER

022505

11

103

MOTO

R--FAN--25W

230V

015184--

1103

+FAN--5

BLA

DE10

”PUSH

013043

1103

OUTLE

TA.--TEE

X25900

1103

SWITCH--PRESSURE350P

SI--SOLD

ER

048231

11

2103

35



DESCRIPTION

PARTS

UPDATE

REMARKS

WARR.

CLASS

339

QTY.

338

QTY.

336

QTY.

PART

NUMBER

VALVE--W

ATER3/8REG\HEADPRESS

008363

103

VALVE--W

ATER3/8REG/HEADPRESSURE

046686

11

2013

50Hz

BELT--AX33

024396

4000

BELT--AX39

023874

4000

BLO

CK--TERMINAL2POLE

039421

2103

220--240/50/1

BLO

CK--TERMINAL--2

POLE

039422

2103

BLO

CK--TERMINAL--7

POLE

GREEN

024156

1103

COMPRESSORCOMPONENTS

CAPACITOR--R

UN25UF/370VOLT

023739

1103

220--240V50HZ1P

H

CAPACITOR--STA

RT

031790

1103

220--240V50HZ1P

H

RELAY--STA

RT--C

OMPRESSOR

038146

1103

220--240V50HZ1P

H

CAPACITOR--R

UN--35UF/370V

029439

1103

220--240V50HZ1P

H

CAPACITOR--STA

RT--135--155UF/33

036048

1013

220--240V50HZ1P

H

RELAY--STA

RT--C

OMPRESSOR

036047

1103

220--240V50HZ1P

H

CAPACITOR--R

UN

035734

2103

220--240V50HZ1P

H

CAPACITOR--STA

RT

031790

2103

220--240V50HZ1P

H

RELAY--STA

RTCOMPRESSOR

048764

2103

220--240V50HZ1P

H

DIAGRAM--W

IRING

038333--34

1000

DIAGRAM--W

IRING

051624--40

1000

DIAGRAM--W

IRING

046585--34

1000

PULLEY2A

K25

X.625

021076

22

2103

BEATERMOTO

R

VIDEO--TRAIN

FILM--SS--SOFTECH

038047--PAL

11

1000

Model 336038333Rev. 11/02

Model 336038333-33Rev. 11/02

Model 336038333-62Rev. 11/02

Model 338051624--27Rev. 11/02

Model 338051624--33Rev. 11/02

Model 338051624--40Rev. 11/02

Model 338051624--58Rev. 11/02

Model 339046585--27Rev. 11/02

Model 339046585--33Rev. 11/02

Model 339046585-62Rev. 11/02

freezemaster 300 series - sreweb.comsreweb.com/manual/taylor_manuals/model_336_338-339.pdf ·...

Documents