forged carbon & stainless steel valves · 1/19/2020 · for stainless steel and a350lf2 for...

Forged Carbon & Stainless Steel ValvesGate | Globe | Check

All rights reserved. All valves information and its contents hereof are proprietary to NCI. Any unauthorized reproduction or disclosure, in whole or in part is strictly prohibited. All valves materials, images and data sheets in this catalogue / brochure is for general information and shall not be used for specific performance data and material selection without first consulting with NCI. NCI reserves the right to change the enclosed valves information without notice. NCI does not accept any liability or damages arising from the use of any valve information within this document. All trademarks and registered trademarks are owned by their respective companies.

NCI Forged Carbon & Stainless Steel Valves

2

Product FeaturesDesign, Features and Standards .........................................4

Material SpecificationsBody and Trim Materials .....................................................5

Code IndexHow to Order Forged Steel Valves .......................................6

Gate ValvesGS08TD(SW) | Class 800 ..................................................7

Globe ValvesSL08TD(SW) | Class 800 ..................................................8

Check ValvesCS08TD(SW) | Swing | Class 800 ...................................9

CP08TD(SW) | Piston/Lift | Class 800 ............................ 10

Engineering SpecificationsPressure - Temperature Ratings ....................................... 11

Flow Coefficients Cv ......................................................... 11

Terms & Conditions

Table of ContentsForged Steel Valves



3

Designed and Manufactured to the Following Industry Standards• All forged steel valves are designed to API602.

• Pressure/Temperature rating conforms to ANSI/ASME B16.34.

• NACE package are designed and manufactured to NACE MR0103.

• All valves are tested according to API598.

• Connection ends are designed and manufactured to ANSI/ASME B1.20.1 for NPT thread ends and B16.11 for Socket Weld ends.

Standard Forged Steel Valve In-Stock ItemsGate Valves, Globe Valves, Swing and Lift Check Valves are available standard in-stock with the following specifications:

• Pressure/Temperature Rating: ANSI Class 800

• Size: ½" to 2"

• End Connection: NPT x NPT, SW x SW, and NPT x SW

• Bonnet: OS&Y and Bolted

• Body Material: A105N, A182-F316L, and A350-LF2

Introduction and Features • NCI manufactures and stocks full line of commercial forged carbon

steel and stainless steel gate, globe and check valves strictly engineered and manufactured to API, ANSI, ASME, ASTM and other recognized industrial standards.

• NCI forged steel valves are built in various body materials, trim options and connection styles – offering the solution to your specific application needs in Petroleum Refineries, Chemical Process and Power Generation.

• Body materials are standardized to A105N for carbon steel, 316SSL for stainless steel and A350LF2 for low carbon steel structures. Other ASME B16.34 materials are available upon request.

• The carbon steel and low carbon steel valves with NACE package comply with NACE MR0103 specification, and contain no copper bearing alloys.

• NCI forged steel valves come standard with Stellite#6 hard-faced seat rings with solid wedge for gate valves and renewable discs for globe and check valves.

• Designed to API602/ASME B16.34, all NCI forged steel valves come with Class 800# rating (1500# optional) with a size range from ½" thru 2", NPT or Socket Weld ends. Other connection styles including Butt Weld or RF Flanges are also available upon special request.

Product Features Forged Steel Valves



4

* Standard Materials** Other Materials available on request

Body, Bonnet/Cover Materials

NCI Material Code

ASTM Specification

Nominal Designation

Recommended Service Condition

A5* A105N Carbon Steel General non-corrosive water, steam, oil and gases services between -20°F(-29°C) and 800°F(425°C).

LF* A350-LF2 Low Temp. C.S. General non-corrosive water, steam, oil and gases services between -50°F(-46°C) and 650°F(343°C).

SL* A182 F316L Stainless Steel Corrosive services, Acetic acid, calcium carbonate, calcium lactate, sea water, steam and sulfites up to 800°F(427°C).

Trim Specification

NCI Trim Code

API Trim #

API Nominal Trim

Seat Surface Material

Seat Surface Specification

Stem/Bushing Material

Stem/Bushing Specification

Recommended Service Applications†

05* 5 Hardfaced Co-Cr A – 13Cr ASTM A276 T410/T420

High pressure and slightly erosive and corrosive services. Excellent for high pressure water and steam service.

08* 8F6 13Cr ASTM A182 (F6a) – ASTM A276

T410/T420Universal trim for general service requiring long service life. As trim 5 for moderate pressure and more corrosive service. Steam, gas and general service.Hardfaced Co-Cr A – – –

10 10 316 18Cr-8Ni ASTM A182 (F316) 18Cr-8Ni-Mo ASTM A276 T316

For superior resistance for liquids and gases which are corrosive to 410 Stainless Steel. Low temperature service standard for 316SS valves.

12* 12316 18Cr-8Ni-Mo

ASTM A182 (F316)18Cr-8Ni-Mo ASTM A276 T316 As trim 10 but for medium pressure and more

corrosive or asrasive service.Hardfaced Trim 5 or 5A – –

14 14Alloy 20 19Cr-29Ni ASTM B473 19Cr-29Ni ASTM B473

As trim 13 but for medium pressure and more corrosive service.Hardfaced Trim 5 or 5A – – –

NOTE: Data provided in this chart is for informational purpose only. Always consult current API publications to verify information and trim data† Temperatures shown may vary depending on media, pressure and service applications* Standard Materials** Other Materials available on request

Material SpecificationsForged Steel Valves



5

1 CATEGORYGS Gate Valve Solid Wedge CS Check Valve Swing

SL Globe Valve Linear CP Check Valve Piston

6 TRIM DESIGN05 API Trim 5, Hardfaced 10 API Trim 10, 316

08 API Trim 8, F6 and Hardfaced 12(ST) API Trim 12, 316 and Hardfaced

9 SIZES001 1/4" 010 1"

003 3/8" 012 1-1/4"

005 1/2" 015 1-1/2"

007 3/4" 020 2"

3 END STYLESW Socket Weld TD Threaded

ST Socket Weld x Threaded

2 PRESSURE RATING08 Class 800

7 ACCESSORIESHW Handwheel EA Electric Actuator

PA Pneumatic Actuator

8 SPECIAL OPTIONSNC NACE for H2S Service TF Teflon Disc Insert

OX Oxygen Cleaning CC Customized Coating

5 BONNET OPTION1 Bolted Bonnet/Cap

4 BODY MATERIALA5 A105N L1 LC1

LF LF2 SL SS 316L

LC LCC

How to Order Forged Steel Valves

1Category Pressure Accessories Options SizeBody Bonnet TrimEnd

2 3 4 6 7 85

– –

9

SG 0 8 T A 5 1 0 0 0 58 H W N CD

Code Index Forged Steel Valves



6

No. Part Name

A105N Body A105N Body NACE 316L SS Body NACE LF2 Body NACE

GS08TD(SW)- A5108HW(Trim 8)

GS08TD(SW)- A5105HW(Trim 5)

GS08TD(SW)-A5108HW-NC

(Trim 8)


(Trim 5)


(Trim 12)

GS08TD(SW)- SL112HW-NC

(Trim 12)

GS08TD(SW)LF112(ST)HW-NC

(Trim 12)

1 Body A105N A105N A105N A105N A105N 316L A350-LF22 Seat A182-F6a+STL A182-F6a+STL A182-F6a+STL A182-F6a+STL A182-F6a+STL 316+STL 316+STL3 Wedge A182-F6a A182-F6a+STL A182-F6a A182-F6a+STL 316 316 3164 Stem A182-F6a A182-F6a A182-F6a A182-F6a 316 316 3165 Bonnet A105N A105N A105N A105N A105N 316L A350-LF26 Packing Graphite Graphite Graphite Graphite Graphite Graphite Graphite7 Gland A276-410 A276-410 A276-410 A276-410 A276-410 A276-316 A276-4108 Gland Flange A105 A105 A105 A105 A105 316 A1059 Stem Nut A108-1045 A108-1045 A108-1045 A108-1045 A108-1045 A276-410 A108-104510 Handwheel QT400 QT400 QT400 QT400 QT400 QT400 QT40011 Lock Nut A194-2H A194-2H A194-2H A194-2H A194-2H A194-8M A194-4M12 Nut A194-2H A194-2H A194-2HM A194-2HM A194-2HM A194-8M A194-4M13 Bolt A193-B7 A193-B7 A193-B7M A193-B7M A193-B7M A193-B8M A320-L7M14 Pin A276-410 A276-410 A276-410 A276-410 A276-410 A276-304 A276-41015 Bonnet Bolt A193-B7 A193-B7 A193-B7M A193-B7M A193-B7M A193-B8M A320-L7M

Description

• Forged Carbon or Stainless Steel Body and Bonnet

• Outside Screw and Yoke (OS&Y)

• Rising Stem / non-rising handwheel

• Bolted Bonnet

• Conventional Port

• Solid wedge and Integral Backseat

• ½"–2" Screwed (NPT) or Socket Weld (SW) ends

• Designed to API 602/ ASME B16.34

• Tested to API 598

• NPT ends conforms to ASME B1.20.1

• SW ends conforms to ASME B16.11

d

LH

( OPE

N PO

SITI

ON)

W

Dimensions

SizeL W H d Weight

mm in mm in mm in mm in kg lbs

1/2" 79 3.1 100 3.9 166 6.5 10.5 0.4 2.2 4.93/4" 92 3.6 100 3.9 169 6.7 13.5 0.5 2.3 5.11" 111 4.4 125 4.9 193 7.6 18 0.7 4.1 9.0

1¼" 120 4.7 160 6.3 230 9.1 23 0.9 5.8 12.81½" 120 4.7 160 6.3 246 9.7 29 1.1 7.0 15.42 140 5.5 180 7.1 283 11.1 36 1.4 10.4 22.9

ASTM A105N, A350-LF2 and A182-F316L Body & Bonnet

Forged Steel Gate Valve | Class 800GS08TD(SW)



7

LSTL

d

H ( O

PEN

POSI

TION

)

W

No. Part Name


SL08TD(SW)- A5108HW(Trim 8)

SL08TD(SW)- A5105HW(Trim 5)

SL08TD(SW)- A5108HW-NC

(Trim 8)


(Trim 5)


(Trim 12)

SL08TD(SW)- SL112HW-NC

(Trim 12)

SL08TD(SW)LF112(ST)HW-NC

(Trim 12)

1 Body / Seat A105N / STL A105N / STL A105N / STL A105N / STL A105N / STL 316L / STL A350-LF2 / STL2 Disc A182-F6a A182-F6a+STL A182-F6a A182-F6a+STL 316 316 3163 Stem A182-F6a A182-F6a A182-F6a A182-F6a 316 316 3164 Gasket 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite5 Bonnet A105N A105N A105N A105N A105N 316L A350-LF26 Bonnet bolt A193-B7 A193-B7 A193-B7M A193-B7M A193-B7M A193-B8M A320-L7M7 Pin A276-410 A276-410 A276-410 A276-410 A276-410 A276-304 A276-4108 Bolt A193-B7 A193-B7 A193-B7M A193-B7M A193-B7M A193-B8M A320-L7M9 Nut A194-2H A194-2H A194-2HM A194-2HM A194-2HM A194-8M A194-4M10 Stem nut A108-1045 A108-1045 A108-1045 A108-1045 A108-1045 A276-410 A108-104511 Handwheel QT400 QT400 QT400 QT400 QT400 QT400 QT40012 Lock nut A194-2H A194-2H A194-2H A194-2H A194-2H A194-8 A194-2HM13 Gland Flange A105 A105 A105 A105 A105 316 A10514 Gland A276-410 A276-410 A276-410 A276-410 A276-410 A276-316 A276-41015 Packing Graphite Graphite Graphite Graphite Graphite Graphite Graphite

Dimensions

SizeL W H d Weight

mm in mm in mm in mm in kg lbs

1/2" 79 3.1 100 3.9 166 6.5 10.3 0.4 2.2 4.93/4" 92 3.6 100 3.9 175 6.9 12.7 0.5 2.4 5.31" 111 4.4 125 4.9 206 8.1 17 0.7 4.1 9.0

1¼" 120 4.7 160 6.3 228 9.0 23 0.9 5.8 12.81½" 152 6.0 160 6.3 262 10.3 28 1.1 7.8 17.22 172 6.8 180 7.1 300 11.8 36 1.4 12.1 26.7

Description

• Forged Carbon or Stainless Steel Body and Bonnet

• Outside Screw and Yoke (OS&Y)

• Rising Stem

• Bolted Bonnet


• Solid wedge and Integral Backseat


• Designed to API 602/ ASME B16.34




SL08TD(SW)Class 800 | Forged Steel Globe ValveASTM A105N, A350-LF2 and A182-F316L Body & Bonnet



8

No. Part Name


CS08TD(SW)- A5108

(Trim 8)

CS08TD(SW)- A5105

(Trim 5)

CS08TD(SW)- A5108-NC(Trim 8)



CS08TD(SW)- SL112-NC(Trim 12)

CS08TD(SW) LF112-NC(Trim 12)

1 Body A105N A105N A105N A105N A105N 316L A350-LF22 Seat A182-F6a+STL A182-F6a+STL A182-F6a+STL A182-F6a+STL 316 316+STL 316+STL3 Disc A182-F6a A182-F6a+STL A182-F6a A182-F6a+STL A182-F6a+STL 316 3164 Rocker 304 304 304 304 316 316 3045 Gasket 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite6 Cap Bolt A193-B7 A193-B7 A193-B7M A193-B7M A193-B7M A193-B8M A320 L7M7 Cap A105N A105N A105N A105N A105N A276-316L A350-LF2

L

H

d

Dimensions

SizeL H d Weight

mm in mm in mm in kg lbs

1/2" 79 3.1 62 2.4 10.5 0.4 1.6 3.5

3/4" 92 3.6 65 2.6 13.5 0.5 1.8 4.0

1" 111 4.4 78 3.1 18 0.7 2.8 6.2

1¼" 120 4.7 85 3.3 23 0.9 3.9 8.6

1½" 120 4.7 105 4.1 29 1.1 4.6 10.1

2 140 5.5 120 4.7 36 1.4 7.0 15.4

Description

• Carbon or Stainless Steel Body and Cap

• Bolted Cap



• Designed to API 602 / ASME B16.34




ASTM A105N, A350-LF2 and A182-F316L Body & Cap

Forged Steel Swing Check Valves | Class 800CS08TD(SW)



9

No. Part Name


CP08TD(SW)- A5108

(Trim 8)

CP08TD(SW)- A5105

(Trim 5)

CP08TD(SW)- A5108-NC(Trim 8)



CP08TD(SW)- SL112-NC(Trim 12)

CP08TD(SW) LF112-NC(Trim 12)

1 Body / Seat A105N / STL A105N / STL A105N / STL A105N / STL A105N / STL 316L / STL A350-LF2 / STL

2 Disc A182-F6a A182-F6a+STL A182-F6a A182-F6a+STL 316 316 316

3 Gasket 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite 304+Graphite

4 Cap A105N A105N A105N A105N A105N 316L A350 LF2

5 Cap Bolt A193-B7 A193-B7 A193-B7M A193-B7M A193-B7M A193-B8M A320-L7M

L

STL

d

H

Dimensions

SizeL H d Weight

mm in mm in mm in kg lbs

1/2" 79 3.1 62 2.4 10.3 0.4 1.6 3.5

3/4" 92 3.6 65 2.6 12.7 0.5 1.8 4.0

1" 111 4.4 78 3.1 17 0.7 3.1 6.8

1¼" 120 4.7 82 3.2 23 0.9 4.2 9.3

1½" 152 6.0 102 4.0 28 1.1 6.4 14.1

2 172 6.8 120 4.7 36 1.4 10.0 22.0

Description

• Carbon or Stainless Steel Body and Cap

• Bolted Cap



• Designed to API 602 / ASME B16.34




CP08TD(SW)Class 800 | Forged Steel Piston/Lift Check ValvesASTM A105N, A350-LF2 and A182-F316L Body & Cap



10

Pressure - Temperature Ratings for Class 800 Forged Steel Valves

Service Temperature

Maximum Working Pressure (PSIG)A105 (A)(B)

A350-LF (A) A182-F11 (F)(I) A182-F22 (I) A182 F304 (J) A182 F316 (J) A182 F304L (K)

A182 F316L

°F °C PSIG MPA PSIG MPA PSIG MPA PSIG MPA PSIG MPA PSIG MPA

-20 to 100 -29 to 38 1975 13.62 2000 13.79 2000 13.79 1920 13.24 1920 13.24 1600 11.03

200 50 1810 13.37 2000 13.79 2000 13.79 1600 12.75 1655 12.83 1365 10.67

300 100 1745 12.43 1925 13.73 1940 13.74 1435 10.90 1495 11.25 1215 9.28

400 150 1690 12.02 1850 13.26 1880 13.38 1325 9.87 1370 10.27 1120 8.37

500 200 1610 11.68 1775 12.79 1775 12.96 1240 9.19 1275 9.51 1050 7.78

600 250 1515 11.18 1615 12.36 1615 12.36 1180 8.67 1205 8.90 990 7.32

650 300 1465 10.62 1570 11.43 1570 11.43 1150 8.24 1180 8.43 975 6.95

700 325 1415 10.32 1515 11.02 1515 11.02 1125 8.06 1160 8.24 960 6.79

750 350 1350 10.02 1420 10.73 1420 10.73 1100 7.90 1140 8.09 940 6.68

800 375 1100 9.70 1355 10.35 1355 10.35 1080 7.74 1125 7.97 920 6.60

850 400 850 9.26 1300 9.76 1300 9.76 1055 7.58 1115 7.85 900 6.48

900 425 615 7.67 1200 9.34 1200 9.34 1035 7.47 1105 7.77 – 6.36

950 450 365 6.13 850 9.02 1025 9.02 1020 7.31 1030 7.69 – 6.24

1000 475 225 4.65 575 8.45 710 8.45 945 7.18 970 7.64 – –

1050 500 – 3.14 385 6.86 466 7.53 865 7.07 960 7.53 – –

1100 538 – 1.57 255 3.97 295 4.92 685 6.52 815 6.68 – –

1150 550 – – 175 3.39 180 4.17 545 6.28 630 6.65 – –

1200 575 – – 110 2.35 110 2.81 440 5.56 495 6.38 – –

1250 600 – – – 1.63 – 1.84 355 4.50 390 5.31 – –

1300 625 – – – 1.14 – 1.19 300 3.68 310 4.21 – –

1350 650 – – – 0.76 – 0.76 250 3.00 255 3.38 – –

1400 675 – – – – – – 200 2.49 200 2.75 – –

1450 700 – – – – – – 155 2.14 155 2.23 – –

1500 725 – – – – – – 110 1.80 110 1.87 – –

– 750 – – – – – – – 1.54 – 1.56 – –

– 775 – – – – – – – 1.21 – 1.21 – –

– 800 – – – – – – – 0.93 – 0.93 – –

NOTE: In accordance with API 602, the Pressure/Temperature ratings for Intermediate Class 800, the linear interpolation of Standard Class 600 and Standard Class 900 pressure/temperature ratings listed in ASME B16.34. ASME Boiler and Pressure Vessel Code Section II materials that also meet the requirements of the listed ASTM specification may also be used.(A) Permissible, but not recommended for prolonged usage above 800 °F (425°C)(B) Only killed steel shall be used above 850 °F (455°C)(F) Use normalized and tempered material only(I) Permissible, but not recommended for prolonged use above 1100 °F (595°C)(J) At temperature over 1000°F (538°C), use only when carbon content is 0.04% or higher(K) Not to be used over 800 °F (425°C)

Flow Coefficients (Cv / Kv)

SizeGate Valve Globe Valve Swing Check Valve Piston Check Valve

Cv Kv Cv Kv Cv Kv Cv Kv

1/2" 4.2 3.6 1.5 1.3 4.7 4.1 1.4 1.2

3/4" 8.9 7.7 2.7 2.3 8.1 7.0 2.1 1.8

1" 21.5 18.6 5.1 4.4 14.4 12.5 3.9 3.4

1¼" 24.9 21.5 11.2 9.7 32.1 27.8 7.8 6.7

1½" 55.5 48.0 16.5 14.3 35.6 30.8 12.5 10.8

2" 85.4 73.8 27.3 23.6 53.1 45.9 19.1 16.5

Engineering SpecificationsForged Steel Valves



11

1) CANCELLATIONS & RESTOCKING POLICY: Purchase orders once placed by Buyer and accepted by Seller can be cancelled only with Seller’s written consent and upon terms which will save Seller from loss. No orders may be cancelled subsequent to delivery and/or shipment, whichever occurs first. As estimated actual damages, Buyer agrees to pay Seller the greater of Seller’s actual costs incurred prior to cancellation plus a reasonable profit, or the following minimum cancellation charges: a) 20% of Order value if cancelled thirty (30) or more days prior to the original delivery/shipment date; b) 50% of the Order value if cancelled thereafter; or, c) 100% of the Order value of any non-standard items, which are items not built for stock or built to Buyer’s specifications.

2) RETURNED PRODUCT: All sales are final; all custom products (non-stocking) are not subject to return, credit or refund. The return of obsolete and used Products shall not be permitted. The Purchaser shall not return Products without first obtaining Seller’s written permission and shall be subject to a restocking charge. Products must be returned within 10 days after the date that written permission has been given. All transportation charges for any returned Products shall be paid by the Purchaser. Request to return Products must be accompanied by relevant customer order and Seller’s invoice number(s). Final acceptance of returned Products is subject to examination and/or testing. Products will not be accepted for return or credit later than six (6) months after invoicing.

3) PRICES: Possession of price lists will not be accepted by the Seller as an obligation, or offer, to sell any goods listed therein. All prices contained in published price lists are subject to change without notice and supersede those of all previous lists. Prices quoted are based on current exchange rates; Seller reserves the right to adjust pricing to reflect the exchange rate in effect at the product receipt date to Seller’s facility.

4) LIQUIDATED DAMAGES: Liquidated damages will not be accepted in the event of order placement.

5) SALES TAXES, ETC.: The Purchaser shall pay and be responsible for all provincial, local or federal sales, use or other taxes (including general sales or value added taxes) and customs duties now or hereinafter enacted which may be applicable to the sale of the Products or the importation of the Products to the destination specified by the Purchaser and which duties and taxes shall be the responsibility of the Purchaser.

6) CREDIT APPROVAL: Orders are accepted subject to satisfactory credit approval. Pending credit approval, delivery may be delayed without liability to Seller.

7) TERMS OF PAYMENT: The terms of payment for Products purchased pursuant to this Agreement are (I) upon acceptance of the purchase order a deposit in such amount as may be set out in the Seller’s written acceptance notice and (II) the balance within 30 days from the date of invoice. Any invoice amount which is not paid when due shall bear interest at the rate of one and one-half (1 ½%) percent per month until paid in full.

The Purchaser agrees that it will not have any rights of set off against or deduction from the purchase price for the Products payable by the Purchaser pursuant to this Agreement. The Purchaser grants to Seller a purchase money security interest in all Products delivered pursuant to this Agreement and all proceeds thereof (whether cash or non-cash and including, without limitation, accounts, instruments and chattel paper). Any failure by the Purchaser to pay the purchase price in full as provided in this Agreement shall constitute an event of default for purposes of said security interest. Upon the occurrence of any such default, Seller shall have all rights of a secured party after default under applicable law. Any repossession

and removal of any Products shall be without prejudice to any of Seller’s other remedies at law or in equity. The Purchaser agrees, without further consideration, at any time, to do or cause to be done, to execute and deliver, all such further acts and instruments (including, without limitation, financing statements approved for filing) as Seller may reasonably request in order to perfect Seller’s security interest.

8) DELIVERY DATE: Seller will utilize reasonable best efforts to meet the delivery schedules stipulated in this Agreement. In the event the provisions of Section 14 hereof shall apply, the delivery date shall be extended by a number of days that is equal to the duration of the event or condition that is responsible for such delay.

9) TITLE AND SHIPMENT: All quotations and sales are FCA Loaded Truck ValvSource Warehouse (Inco Terms 2010) unless otherwise specified in writing and agreed by both parties. Seller’s responsibility ceases upon delivery to carrier and title shall transfer and risk of loss shall be borne by Buyer at that point. Any expedited or other premium transportation charges requested by Buyer will be for the account of Buyer. Prices include domestic packing, blocked and strapped to open pallets and wrapped in Poly. No claims for price adjustments will be honored unless presented within six (6) months from date of invoice. All quotations are subject to change without notice and prior to sale of goods.

10) INSPECTION BY PURCHASER: All Products must be inspected by the Purchaser upon receipt and the Purchaser and Seller, collectively, agree to file appropriate claims with the carrier when there is evidence of shipping damage, either concealed or external. Claims for shortage or error in shipment or for damage other than shipping damage must be made within 5 days after receipt of shipment, failing which the Purchaser shall be deemed to have accepted the shipment.

11) LIMITED WARRANTY: Purchaser acknowledges that the Products are provided to the Purchaser subject only to the limited warranties provided by the manufacturer of the Products and are subject to all of the conditions, limitations and exclusions set out therein, all of which are hereby accepted by the Purchaser. The warranty exclusions include, without limitation, (I) any defects caused by faulty installation performed by Purchaser or third parties, (II) any damage caused by the contractors or tradesman of the Purchaser, (III) any damage caused by improper use or misuse, including exposure to excessive temperatures, moisture or cleaning agents and solvents and (IV) any damage caused during transportation or improper storage. Claims for warranty repairs and replacements must be made within the applicable time period described in the manufacturer’s limited warranty. In no event shall Seller be liable for other than the repair or replacement of any defective Products. In no event shall Seller be liable for any damages, direct or indirect, special or consequential, including, without limitation, damages for lost profits, business interruption, or economic loss arising out of defects in the Products.

12) EXCLUSION OF WARRANTIES: Except as expressly set forth herein seller disclaims all warranties with regard to the products including, without limitation, all implied warranties of merchantability and fitness for a particular purpose.

13) CATALOGUE AND OTHER PRINTED MATTER: Seller’s illustrations are representations of a certain size of each line of Product, but do not necessarily represent all sizes and materials in detail. Similarly, dimensions, weights and material information have been prepared with care, but their correctness is not guaranteed. Seller reserves the right to vary the designs and dimensions without notice.

14) FORCE MAJEURE: Any delay or failure of performance by Seller shall be excused if and to the extent caused, directly or indirectly, events beyond Seller’s control including, without limitation, fire, flood earthquake, lightning, hurricane, explosion, accident or breakdown, acts of God, embargo, strike, labour dispute, labour trouble, lockout, shortage or control of power supply, shortage of supplies or raw materials, or any causes whether of the same kind as the causes enumerated before or not. Subject to any express provisions of this Agreement, any such causes of delay shall extend the time of performance by the length of delay occasioned thereby.

15) NO WAIVER: No waiver by Seller of any right hereunder or of any right granted in connection with a failure to perform or breach by the Purchaser shall be deemed as a waiver of any other right hereunder or of any right granted in connection with any other failure or breach by the Purchaser, whether of a similar nature or otherwise.

16) NOTICE: Any notice made under or in relation to this Agreement shall be sent to the addresses first above written or such other address as the intended recipient shall have previously designated by written notice, by postage prepaid registered mail or by telegram including telex, followed by a confirmation letter by postage prepaid and return receipt requested registered mail. The notice shall be deemed to be made on the fifth day following the date of mailing.

17) ENTIRE AGREEMENT: This Agreement contains the entire agreement and understanding of the parties hereto with respect to the subject matter of this Agreement, and supersedes all prior discussions, agreements, understandings of any and every nature, whether written or oral, between the parties with respect to the subject matter of this Agreement, and no condition, definition, warranty or representation other than those expressly provided for in this Agreement with respect to the subject matter of this Agreement shall be binding upon either party hereto.

18) AMENDMENTS IN WRITING: Any amendment, modification, change or alteration of this Agreement shall be made in writing which expressly refers to this Agreement and which is signed by a duly authorized officer or representative of each of the parties hereto.

19) SEVERABILITY: All provisions of this Agreement are severable and this Agreement shall be interpreted and enforced as if all completely invalid or unenforceable provisions were not contained herein. All partially valid and enforceable provisions shall be enforced to the extent they are valid and enforceable.

20) NO AGENCY OR PARTNERSHIP: Nothing herein contained shall be deemed or construed to constitute either party the agent or partner of the other. Neither party shall have any right, title or authority to enter into any contract, agreement or commitment on behalf of the other or to bind the other in any manner whatsoever.

21) GOVERNING LAW: This agreement shall be governed by and construed in accordance with the laws of the jurisdiction from which the products are shipped by the seller to the purchaser and the parties hereby attorn to the courts of such jurisdiction.

22) ENUREMENT: This Agreement shall enure to the benefit of and be binding upon the parties hereto and on their successors and permitted assigns.

23) SELLER DEFINED: For the purposes hereof, Seller means the Corporation listed as such on the front page of the Invoice or acceptance notice of which these terms and conditions of sale form a part.

VSTC-18-3 | Effective July 1, 2018 Terms & Conditions

• 1,2,3 Piece Ball Valves• Flanged Floating Ball Valves• Knife Gate Valves• Butterfly Valves• Actuation• Position Switches

• Y, Basket & Temporary Strainers• Check Valves• Triple Duty Valves• Foot Valves• Expansion Joints

• Pressure Gauges & Accessories• Temperature Indicators• Needle Valves • Thermowells & Thermocouples

• Brass Ball Valves• Bronze Gate, Globe, & Check Valves• Cast Iron Gate, Globe, & Check Valves• Cast & Forged Steel Gate, Globe and Check ValvesNCI CANADA INC.

19-0

097-

V12

• Cast Gate, Globe & Check Valves• Forged Gate, Globe & Checks• Threaded Ball Valves• Flanged Ball Valves

Oakville, Ontario 2305 Wyecroft RoadOakville, ON L6L 6R2 Telephone: (905) 608-2200Fax: (905) [email protected]

Edmonton, Alberta 7136 – 56 Avenue NW Edmoton, AB T6B 1E4Telephone: (780) 461-6499Fax: (780) [email protected]

Calgary, Alberta 3815 – 32nd Street NECalgary, AB T1Y 7C1Telephone: (403) 236-4888Fax: (403) [email protected]

Saving money on valves has never been easier, contact us today to learn more!

Your source for valves, strainers and gauges!

ValvSource.comLearn more, visit us online at

forged carbon & stainless steel valves · 1/19/2020 · for stainless steel and a350lf2 for...

Documents