for dishwasher of instructions summary select programme · lid. click! very dirty dishes, a lot of...
TRANSCRIPT
Fill with rinse aid
Fill with detergent
Select programmeSu
mm
ary
of
inst
ruct
ion
s fo
r di
shw
ashe
rBrief and handy:everything your dishwasherneeds...Before using for the firsttime, read the installationand operating instructions!
Fill with special salt
Switch on appliancePress On/Off switch, running time of thechosen programme appears
When the display shows 0 (end of programme),press On/Off switch
Switch off the appliance Everything O.K...
9000
236
291
� ���� �
��
en Set the water softening system * Quickly sorted ...
Find out the water hard-ness at your water utilitycompany and enter
* only before using the dish-washer for the first time orif the water hardnesschanges
Read off the setting ... and then set
– Hold down programme button B and switch on the mainswitch, then release the buttons. The display of button Band the number 4 set by the factory flash.
– Each time button B is depressed, the setting increases byone; if 7 has been reached, the display jumps back to 0.
– Switch off the main switch. The selected setting has beenstored in the appliance.
Reset
A B C
B
Dissolves limescale (not required for set value 0!)
Unscrewthe lid.
Only before usingthe dishwasherfor the first timepour approx. 1 l /2 pt water into thesalt opening.
Pour in max.1.5 kg / 3 lb 5 ozsalt (never deter-gent!)
Screw on thelid. Switch ondishwasherimmediately.
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,lift up lid 2.
Pour inrinse aid.
Close thelid. CLICK!
Very dirty dishes, a lot of detergent ...
If required, openthe lid (press thepin).
Warning,
combination products are notsuitable for allprogrammes, follow manufac-turer’s instructions.
Pour indetergent.
Push the lidshut, press.PLOP!
Quick, economical or intensive ...
The max. possible number of programmes is illustrated in thisoverview. The corresponding programmes for your appliancecan be found on the fascia.
Overview of programmes
The programme data has been measured in the laboratoryaccording to European standard EN 50242. Deviations arepossible in practice.* Consumption values for comparative programme with“Eco option” additional function.
932,002016
70 (140)*1,44 (1,05)*
14 (12)*–
750,901411
300,8010–
190,05
4–
74-801,50-1,55
–15-20
Quick45�
Daily50�
Intensive70�
Auto55� /65�
Delicate40�
Duration in minutes
Energy Consumption: kWh
Water consumption in litres
With Aquasensor
Pre-rinse
Additional programmes ** Flexibility ...
Eco option
... If the running timeis extended, water andenergy are conserved.
Timer programming
... switch on,immediately press timerprogramming button:start of programme isdelayed in 1-hour steps.
h.
Half load
... for a few items, saveswater, energy and time
** some models
Maintenance and care For perfect rinsing results ... Cleaning the waste-water pump *
Strainers ...Check, ifrequired, clean
Rotate filtercylinder, removefilter system ...
rinse underflowing water ...
Insert ... Screw in filtersystem NOTEMARK!
* With some models
– Ladle out water and remove filters– Unscrew cover (Torx T20)– Check area of fan impeller for foreign objects– Screw in cover and insert filters
Spray arms ...Removeblockages/deposits
Pull lower armupwards ...
Unscrew upperarm ...
Clean spray nozzlesunder flowing water(perhaps withtoothpick) ...
Insert lower arm ...
Screw in upper arm
Rectifying minor faults yourself ... ... as it is worth doing it yourself!
Fault Possible causes
Appliance is not running /stops
Check water supplyDisplay lights up
Supply fitting not open
Supply hose kinked
Supply fitting jammed or calcified
Open supply fitting.
Install supply hose without kinks.
1. Unscrew water connection.2. Clean filter in the water connection.3. Flow rate must be min. 9 l/min. whenwater supply is open.If the flow rate is less, replace thesupply fitting.
Remedial action
Plastic / utensilsdiscoloured
Too little detergent
Discoloration caused by food colourings(tomato sauce)
Follow manufacturer’s instructions(detergent).
Discoloration is harmless; subsequentrinse cycles will cause it to fade.
Residual waterin the appliance
Waste water pump blocked
The programme has not yet ended
Clean waste-water pump (see above).
Close appliance and switch on.or terminate programme (seeTerminating the programme).
Rust on the cutlery Cutlery not rust-resistantHard knife blades are more susceptible
Extraneous rust
Use dishwasher-proof cutlery.
Never wash rusting partsin the appliance.
Fault Possible causes Remedialaction
Stains and streaks
Milky film on the utensils(removable)
Rinse-aid dosage too high / too low
Glasses not dishwasher-proof.
Streaks: reduce dosage.
Water or limescale stains: increasedosage.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
More information can be found in the operating instructions
Milky film, glassescloudy / dull (not removable)
Water softening system incorrectly set;
No salt
Correctly set water softening system.
Refill with salt.
Utensils are not clean
Sand or gritty residueon the utensils
Utensils are situated close togetheror one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Separate the utensils, prevent contactpoints.
Follow manufacturer’s instructions(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the sprayarms can rotate freely.
Stopping the programme ... Loading the dishwasher correctly ...
Press and hold the two reset buttons simultaneously forapproximately 3 seconds whilethe programme is running(RESET)
”0” appears
The programme will stopafter 1 minute
Switch off the appliance.Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove,large remnants of jam, dairy products and food) according to the operating instructions and check thatthe spray arms can rotate freely.