fog lights

Publications No.

Issue DateINSTALLATIONINSTRUCTIONS

Accessory Application

© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40362 (0808) 1 of 1208V31-SNA-1D00-91

AII40362FOG LIGHTS

P/N 08V31-SNA-100D2009 CIVIC

4-DOORAUG 2008

PARTS LIST

Right fog light

Left fog light

Switch harness

Fog light harness

Sub harness

Combination light switch

6 Wire ties

Clip

2 Self-tapping screws

20 A Fuse(Some may not used.)

Relay

Ground bolt

2 Spring nuts

www.collegehillshonda.com

2 of 12 AII 40362 (0808) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

Ratchet

10 mm and 12 mm Sockets

Blanket

Diagonal cutters

5 mm Hex wrench

Illustration of Fog Lights installed on the vehicle

851210AK

SUB HARNESS

COMBINATION LIGHT SWITCH

SWITCH HARNESS

RELAY

LEFT FOG LIGHTFOG LIGHT HARNESS

RIGHT FOG LIGHT

20 A FUSE

INSTALLATION

1. Make sure you have the anti-theft codes for the audio system and navigation system (if equipped), then write down the radio presets.

2. Disconnect the negative cable from the battery.

3. Remove the front bulkhead cover (two expansion clips, three clips, and move the right and left fender trims inward).

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

5202062T

EXPANSION CLIPS

3 CLIPS(Pull straight up.)

PANEL

RIGHTFENDER TRIM

FRONT BULKHEAD COVER

LEFT FENDER TRIM


© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40362 (0808) 3 of 12

4. With the help of an assistant, remove the front bumper (four long clips, four center clips, two socket bolts, and two self-tapping screws). To prevent damage, set the front bumper on a blanket.

5. Remove the left fog light cover (four pawls).

850904AK

2 SELF-TAPPING SCREWS

LONG CLIPS

CENTER CLIPS

LONG CLIPS

SOCKET BOLTS

FRONTBUMPER

840301AK

LEFT FOG LIGHT COVER

4 PAWLS

FRONT BUMPER

6. Install the spring nut onto the front bumper.

7. Install the left fog light to the fog light cover opening, and secure it with the self-tapping screw.

8. Repeat steps 5 through 7 on the other side.

9. Route the fog light harness 2-pin connector between the lower grille and the front bumper from the right side through the left side.

850801AK

SELF-TAPPING SCREW

FRONT BUMPER

FRONT BUMPER

SPRING NUT

FOG LIGHT COVER OPENING

LEFT FOG LIGHT

850802AK

FRONT BUMPER

FOG LIGHT HARNESS 2-PIN CONNECTOR

FOG LIGHTHARNESS2-PIN/4-PINCONNECTORS

FRONT BUMPERFOG LIGHT

HARNESS

LOWER GRILLE



10. Attach the clip on the fog light harness to each hole of the lower grille.

11. Secure the fog light harness to the lower grille with one wire tie.

12. Plug the fog light harness 2-pin connector into the left fog light bulb.

850901AK

FOG LIGHT HARNESS

LOWER GRILLE

FOG LIGHT HARNESS CLIPS(Attach them to the hole on the lower grille.)

WIRE TIE

LOWER GRILLE

FOG LIGHT HARNESS

850902AK

FOG LIGHT HARNESS2-PIN CONNECTOR

LEFT FOG LIGHT BULB

13. Plug the fog light harness 2-pin connector into the right fog light bulb.

14. Install the fog light harness clip onto the lower grille rib.

15. Remove three bolts from the washer resvoir tank.

850903AK

LOWER GRILLE RIB

FOG LIGHT HARNESS2-PINCONNECTOR

RIGHTFOG LIGHTBULB

FOG LIGHT HARNESS CLIP

852101AK

3 BOLTSWASHER RESERVOIR TANK



16. Locate the 1-pin connector blue-taped to the vehicle harness and remove the blue tape to free the 1-pin connector. Plug the vehicle 1-pin connector you just freed into the sub harness 1-pin connector.

860601AK

VEHICLE HARNESS

BLUE TAPE(Remove.)

SUB HARNESS1-PIN CONNECTOR

SUB HARNESSVEHICLE 1-PIN CONNECTOR

17. Route the sub harness between the washer reservoir tank and vehicle panel as shown.

18. Secure the sub harness ground terminal to the vehicle frame using the ground bolt supplied.

19. Reinstall the washer reservoir tank. Check that the pipe is installed securely.

852910BK

SUB HARNESS

VEHICLE FRAME

VEHICLE PANEL

WASHER RESERVOIR TANK

SUBHARNESS GROUND TERMINAL

GROUND BOLT

PIPE



20. Secure the sub harness clip to the vehicle frame, and secure the sub harness to the vehicle harness using two wire ties.

21. Slide the clip onto the sub harness 4-pin connector, and secure it to the vehicle frame.

22. Plug the fog light harness 4-pin connector to the sub harness 4-pin connector, then reinstall the front bumper.

860602BK

VEHICLE FRAMESUB HARNESS

WIRE TIES


SUB HARNESS CLIP

CLIP

851201AK

FOG LIGHT HARNESS4-PIN CONNECTOR


FRONT BUMPER

23. If equipped, remove the driver’s dashboard under cover by turning the knob counterclockwise, and releasing two clips and pin. Take care not to damage the clips.

24. Remove the driver’s dashboard lower cover (eight clips). Take care not to damage the clips.

5202112T

PIN

2 CLIPS

KNOB

DRIVER’S DASHBOARD UNDER COVER

5202121T

8 CLIPS

DRIVER’S DASHBOARD LOWER COVER



25. Lower the tilt lever, and pull the steering wheel toward you. Insert a flat-tip screwdriver along the guide of the column lower cover, and pry the retaining tab of the column upper cover.

26. Push on the column lower cover in the area shown to separate the column upper cover from the column lower cover (three retaining tabs). Pull up to remove the column upper cover (two hooks).

5308521T

RETAINING TAB

FLAT-TIP SCREWDRIVER

STEERING WHEEL(Pull toward you.)

2 RETAINING TABSCOLUMN UPPER COVER

TILT LEVER

GUIDE

COLUMN LOWER COVER

Push.

HOOKS

RETAINING TAB

27. Remove the column lower cover (two self-tapping screws and one screw).

28. Push the retaining tab from the vehicle white 34-pin connector, and raise the lock lever from connector. Remove the connector from the fuse box. Close the lock lever on the vehicle white 34-pin connector and remove the cover by sliding it from the connector.

5308530T

COLUMN LOWER COVER

SELF-TAPPING SCREWSSCREW

851202AK

Push.

VEHICLE WHITE 34-PIN CONNECTOR

WHITE 34-PIN CONNECTOR

Push. Slide.

Push.RETAINING TAB

COVERFUSE BOX

LOCK LEVER



29. Insert the two switch harness terminals into the white/red terminal and blue terminal of the vehicle white 34-pin connector.

30. Reinstall the vehicle white 34-pin connector.

31. Route the switch harness above the vehicle knee bolster.

5307170T

SWITCH HARNESS TERMINALS

WHITE/RED TERMINAL

BLUE TERMINAL

VEHICLE WHITE34-PIN CONNECTOR

LOCK LEVER

SWITCH HARNESS

Harness Side View

5307180T

VEHICLE KNEE BOLSTER

SWITCH HARNESS

32. Plug the relay into the switch harness relay block, then slide the relay block onto the vehicle bracket stay.

33. Locate the 1-pin connector blue-taped to the vehicle harness. Plug the switch harness 1-pin connector into the vehicle 1-pin connector.

5307192T

SWITCH HARNESS RELAY BLOCK

VEHICLE BRACKET STAY

RELAY

SWITCH HARNESS

5307202T

SWITCH HARNESS

VEHICLE 1-PIN CONNECTOR

SWITCH HARNESS 1-PIN CONNECTOR



34. Secure the switch harness to the vehicle harness and vehicle knee bolster with three wire ties in the areas shown.

35. Lower the tilt lever and pull the steering wheel toward you.

36. Turn the steering wheel 90° counterclockwise.

37. Unplug the vehicle 12-pin connector from the combination light switch. Remove the two screws from the combination light switch. While pushing the retaining tab, slide the combination light switch out, and remove it from the steering column. Do not pull on the lever when removing the case. Do not damage the tab hole of the steering column.

5307212T

SWITCH HARNESS

WIRE TIE

WIRE TIES VEHICLE

HARNESS

VEHICLE KNEE BOLSTER

851203AK

STEERING COLUMN

SCREWS

STEERING WHEEL

RETAINING TAB



CASE

LEVER

TAB HOLE


38. Install the new combination light switch on the steering column using the two screws. Hold the case by hand, then install the new combination light switch to the steering column. Do not push on the lever when installing the case. Push in on the case and securely set the retaining tab into the tab hole.

39. Plug the vehicle 12-pin connector to the new switch. Replace the vehicle harness.

851204AK

STEERING COLUMN



2 SCREWS (Reuse.)

RETAINING TAB

CASE

TAB HOLE


LEVER



40. Install the 20 A fuse into the fuse box in the location shown. If the fuse is already installed, it is not necessary to install the 20 A fuse.

41. Check that all wire harnesses are routed properly and all connectors are plugged in.

42. Reinstall all removed parts.

43. Connect the negative cable to the battery and check operation of all lights and other electrical accessories.

44. Enter the anti-theft codes for the audio system and the navigation system (if equipped), and reset the radio station presets.

45. Reset the clock on vehicles without navigation.

5307240T

FUSE LOCATION “6”

20 A FUSE

FUSE BOX

FUSE BOX

USE AND CARE

How to Operate Fog Lights

• Turn the light switch to the “ ” position (headlights on low beam).

• Turn the fog light switch (indicator is on).

NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather.

Adjusting the Aim

1. Adjust the vertical aiming according to local laws and regulations. To adjust, turn the adjusting screw in or out until the correct angle is obtained.

2. Repeat on the right side.

871716BK

FO

G L

IGH

T

SW

ITC

H

OFF

Low High

-

-

-

-

- -

-

OFF

HEADLIGHT SWITCH

ONON

851205AK

To lower.To raise.

ADJUSTING SCREW



BULB REPLACEMENT

1. Remove the self-tapping screw, and pull the fog light out toward you.

2. Push in the retaining tab, and unplug the connector from the fog light.

851206AK

SELF-TAPPING SCREW FOG LIGHT

851207AK

RETAINING TAB(Push.)

CONNECTORLEFT FOG LIGHT

3. Remove the bulb from the fog light by turning it.

851208AK

FOG LIGHT

BULB



4. Install a new bulb on the fog light by turning it clockwise until it stops.

• Take extreme care when replacing the fog light bulb to avoid damaging the lenses or finished surfaces of the body.

• Use only a Honda Genuine halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003

• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution.

• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may blind oncoming drivers.

5. Plug the connector to the bulb.

6. Install the fog light in the reverse order of removal.

7. Check that the bulb comes on properly. Adjust the aim as necessary.

851209AK

CONNECTOR

FOG LIGHT

NEW BULB

Turn the bulb until it stops.


fog lights

Documents