focus beam led - amazon web servicesadjmedia.s3-website-eu-west-1.amazonaws.com/manuals/adj focus...

User Instructions

FOCUS BEAM LED

Europe Energy Saving NoticeEnergy Saving Matters (EuP 2009/125/EC)Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical prod-ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!

©2019 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their respective companies.ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product.FCC STATEMENTThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONSThis product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device uses and can radiate radio frequency energy and, if not installed and used in accordance with the included instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following methods: · Reorient or relocate the device.· Increase the separation between the device and the receiver.· Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected.· Consult the dealer or an experienced radio/TV technician for help.

DOCUMENT VERSIONDue to additional product features and/or enhancements, an updated version of this document may be available online. Please check www.adj.com for the latest revision/update of this manual before beginning installation and/or programming.

07/02/19 1 1.0.2 16 / 18 Initial Version

DateDocumentVersion

SoftwareVersion > DMX Channel Mode Notes

09/26/19 1.2 N/C N/C 3-Pin DMX Updated to 5-Pin

2 1.0.4 N/C“Reset All” Added to DMX ModesPan Degree Selection AddedGamma Removed, Dimming Curves Added

10/31/19

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 2

Focus Beam LED Table of Contents

IntroductionFeatures I Warranty RegistrationSafety PrecautionsOverviewInstallationDMX Set UpDMX AddressingDMX Modes & ValuesSystem MenuMaster-Slave Set UpDimmer Mode Chart I Dimmer Curve ChartStatic Gobos I Dimensional DrawingsFuse Replacement I Multiple Unit Power Linking Trouble Shooting I CleaningLimited Warranty (USA Only)Technical Specifications

34578911121723242526262728


Focus Beam LED IntroductionUnpacking: Thank you for purchasing the Focus Beam LED by ADJ Products, LLC. Every unit has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the ship-ping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support. Introduction: The Focus Beam LED is a DMX intelligent, moviing head, LED fixture. This fixture can be used in a stand alone mode or connected in a Master/Slave configuration. The fixture comes equipped with 2 prisms (8 facet circular & 6 facet linear), focus, frost, 6 different dimming options with dimming speed control. The Focus Beam LED has 2 DMX channel modes; 16 & 18. This product is intended to be used by professionally trained personnel only and is not suitable for private use. Customer Support: Contact ADJ Service for any product related service and support needs. Also visit https://forums.adj.com/ with questions, comments or suggestions.Parts: To purchase parts online visit http://parts.americandj.comADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PSTVoice: 800-322-6337 | Fax: 323-582-2941 | [email protected] SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA 6122 S. Eastern Ave. Los Angeles, CA. 90040323-582-2650 | Fax 323-582-2941 | www.adj.com | [email protected] SUPPLY Europe B.VJunostraat 2 6468 EW Kerkrade, The Netherlands+31 (0)45 546 85 00 | Fax +31 45 546 85 99 www.adj.eu | [email protected] PRODUCTS GROUP MexicoAV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000+52 (728) 282-7070

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ Products, LLC.PLEASE recycle the shipping carton when ever possible.

Focus Beam LED Features

Focus Beam LED Warranty RegistrationThe Focus Beam LED carries a 2 year limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-tacting our customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number on the outside of the package will be returned to the shipper.


• Individual Color and Gobo Wheels• 13 Colors + White & Split Colors• 14 Gobos + Open• Electronic Dimming 0-100%• DMX-512 protocol• 3-Pin DMX Connections (Updated to 5-Pin DMX Connections 9/26/19)• 2 DMX Channel Modes: 16 / 18 • Multiple Unit Power Linking (See page 25)

Included:1 x powerCON Cable1 x Safety Cable2 x Omega Clamps


Focus Beam LED Safety Precautions • DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before servicing. • DO NOT shake the fixture, avoid brute force when installing and/or operating the fixture. • DO NOT operate the fixture if the power cord has become frayed, crimped and/or damaged. If the power cord is damaged, replace immediately with a new one of similar power rating. • DO NOT Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. • DO NOT attempt to operate this unit, if it becomes damaged. • DO NOT spill water or other liquids into or on to your unit. • This unit is intended for indoor use only, use of this product outdoors voids all warranties. • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture • Disconnect from main power before making any type of connection. • DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling. • Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall. • During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. Thsi is a normal process and is caused by excess paint in the interior of the casing burning off from the heat. This will decrease gradually over time. • DO NOT remove the cover under any conditions. There are no user serviceable parts inside. • When installing fixture in a suspended enviroment, always use mounting hardware that is no less than M10 x 25mm, and always install fixture with an appropriately rated safety cable. • Never operate this unit when it’s cover is removed. • Never plug this unit in to a dimmer pack • During long periods of non-use, disconnect the unit’s main power. • Always mount this unit in safe and stable matter. • Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit. • Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 25 for cleaning details. • Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. • The fixture should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the fixture. C. The fixture has been exposed to rain or water. D. The fixture does not appear to operate normally or exhibits a marked change in performance. E. The fixture has fallen and/or subjected to extreme handling.


Focus Beam LED Safety Precautions

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMSExternal sources of light beams from direct sunlight, lighting moving head fixtures, and lasers, which are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ lighting fixtures, can cause severe internal damage including burning to optics, dichroic color filters, glass and metal gobos, prisms, animation wheels, frost filters, iris, shutters, motors, belts, wiring, discharge lamps, and LEDs.This issue is not specific only to ADJ lighting fixtures, it is a common issue with lighting fixtures from all manufacturers. Although there is no true way to fully prevent this issue from happening, the guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service for more details.DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.


Focus Beam LED Overview

1. Service Port

2. LED Display

3. LEFT Button

4. DOWN Button

5. ENTER Button

6. RIGHT Button

7. UP Button

8. MODE Button

9. powerCON In

10. Fuse (3A)

11. 3-Pin DMX In/Out 5-Pin DMX In/Out (Updated 9/26/19)

12. powerCON Out

FOCUS BEAM LED

1 2 3 4 5

6

78

10 11 12910 11 129

FOCUS BEAM LED

1 2 3 4 5

6

78

UPDATED 9/26/19


Focus Beam LED Installation

Screw one clamp each via a M12 screw and nut into the Omega bracket. Insert the quick-lock fasteners of the Omega holder’s into the respective holes on the bottom of the Focus Beam LED. Tighten the quick-lock fasteners fully clockwise. Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails. Pull the safety cable through the openings located on the base plate and over the trussing system or a safe fixation spot. Insert the end in the carabine and tighten the safety screw. Note: Never use the carrying handles for secondary attachment.

NOTICE: When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without any deformation. The suitable enviromental temperature for this lighting fixture is between -25˚ C to 45˚ C. Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above. This will allow the fixture to run at its best and help prolong the fixture life. Be sure this fixture is kept at least 12m (40ft) away from any flammable materials (decoration etc.).

SAFETY CABLE RIGGING POINT

OMEGA BRACKET ATTACHMENT POINTS


Focus Beam LED DMX Set UpDMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal). DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Beam LED can be controlled via DMX-512 protocol. The Focus Beam LED has 2 DMX channel modes. The DMX address is set on the front panel of the Focus Beam LED. Your unit and your DMX controller require a standard 3-pin XLR connec-tor for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split.

Figure 1

Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.

DMX512 IN3-PIN XLR

SOUNDREMOTECONTROLINPUT

POWER

INPUT OUTPUTSOUND

REMOTECONTROLINPUT

POWER

INPUT OUTPUTSOUND

REMOTECONTROLINPUT

POWER

INPUT OUTPUT

DMX512DMX+,DMX-,COMMON

1

23

Termination reduces signal errors andavoids signal transmission problemsand interference. It is always advisableto connect a DMX terminal, (Resistance120 Ohm 1/4 W) between PIN 2 (DMX-)and PIN 3 (DMX +) of the last fixture.

1

23

1

23

DMX +

DMX -

COMMON

DMX512 OUT3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Configuration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground


Special Note: Line Termination. When longer runs of cable are used, you may need to use a termina-tor on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

Focus Beam LED DMX Set Up

DMX512 IN3-PIN XLR

SOUNDREMOTECONTROLINPUT

POWER

INPUT OUTPUTSOUND

REMOTECONTROLINPUT

POWER

INPUT OUTPUTSOUND

REMOTECONTROLINPUT

POWER

INPUT OUTPUT

DMX512DMX+,DMX-,COMMON

1

23

Termination reduces signal errors andavoids signal transmission problemsand interference. It is always advisableto connect a DMX terminal, (Resistance120 Ohm 1/4 W) between PIN 2 (DMX-)and PIN 3 (DMX +) of the last fixture.

1

23

1

23

DMX +

DMX -

COMMON

DMX512 OUT3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-512 data cables for DATA transmis-sion in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)Pin 1

Do Not Use

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion


Focus Beam LED DMX Addressing

All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment of this starting DMX address is achieved by setting the correct DMX address on the digital control display on the fixture.You can set the same starting address for all fixtures or a group of fixtures, or set different addresses for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to react in the same way, in other words, changing the settings of one channel will affect all the fixtures simultaneously.If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number you have set, based on the quantity of DMX channels of each fixture. That means changing the settings of one channel will only affect the selected fixture.In the case of the Focus Beam LED, when in 16 channel mode you should set the starting DMX ad-dress of the first unit to 1, the second unit to 17 (16 + 1), the third unit to 33 (17 + 16), and so on. (See the chart below for more details.)

Channel Mode Unit 1 Address

Unit 2 Address

Unit 3 Address

Unit 4 Address

16 Channels 1 17 33 49

18 Channels 1 19 37 55


Focus Beam LED DMX Modes & Values

1 1PAN MOVEMENT 8-BIT:Pan Movement (0° - 630°)

2PAN FINE 16-BIT:Fine Control of Pan Movement

2 3TILT MOVEMENT 8-BIT:Tilt Movement (0° - 270°)

4TILT FINE 16-BIT:Fine Control of Tilt Movement

3 5

COLOR WHEEL:

Functions16 Channels 18 Channels Values

Open / WhiteWhite + RedRedRed + Light BlueLight BlueLight Blue + GreenGreenGreen + YellowYellowYellow + OrangeOrangeOrange + MagentaMagentaMagenta + AmberAmberAmber + LimeLimeLime + PurplePurplePurple + PinkPinkPink + CyanCyanCyan + CTOCTOCTO + BlueBlueBlue + WhiteClockwise Rotation Fast - SlowStopCounter-Clockwise Rotation Slow - Fast

000-004005-011012-018019-025026-032033-039040-046047-053054-060061-067068-074075-081082-088089-095096-102103-109110-116117-123124-130131-137138-144145-151152-158159-165166-172173-179180-186187-193194-220221-229230-255

000-255

000-255

000-255

000-255

NOTE: The Prism and Frost channels CANNOT be used at the same time. The Frost channel will override the Prism channel.



4 6

5 7

GOBO WHEEL:Functions16 Channels 18 Channels Values

OpenGobo 1Gobo 2Gobo 3Gobo 4Gobo 5Gobo 6Gobo 7Gobo 8Gobo 9Gobo 10Gobo 11Gobo 12Gobo 13Gobo 14OpenGobo 1 ShakeGobo 2 ShakeGobo 3 ShakeGobo 4 ShakeGobo 5 ShakeGobo 6 ShakeGobo 7 ShakeGobo 8 ShakeGobo 9 ShakeGobo 10 ShakeGobo 11 ShakeGobo 12 ShakeGobo 13 ShakeGobo 14 ShakeOpen ShakeCounter-Clockwise Rotation Fast - SlowStopClockwise Rotation Slow - Fast

000-003004-007008-011012-015016-019020-023024-027028-031032-035036-039040-043044-047048-051052-055056-059060-063064-068069-072073-076077-080081-084085-089090-093094-097098-101102-105106-110111-114115-118119-122123-127128-189190-193194-255

PRISM 1 (8 FACET CIRCULAR):CloseOpen

000-007008-255

6 8

ROTATING PRISM 1 (8 FACET CIRCULAR):IndexingClockwise Rotation Fast - SlowStopCounter-Clockwise Rotation Slow - Fast

000-127128-189190-193194-255

7 9PRISM 2 (6 FACET LINEAR):CloseOpen

000-007008-255

8 10

ROTATING PRISM 2 (6 FACET LINEAR):IndexingClockwise Rotation Fast - SlowStopCounter-Clockwise Rotation Slow - Fast

000-127128-189190-193194-255



SHUTTER & STROBING:Functions16 Channels 18 Channels Values

CloseOpenStrobing Slow - FastOpenPulsating StrobeOpenRandom Strobing Slow - FastOpen

000-031032-063064-095096-127128-159160-191192-223224-255

9 11

MASTER DIMMER:0% - 100% 000-255

FOCUS:Linear Near - Far000-255FROST:

000-255

PAN/TILT SPEED:Fast - Slow 000-255

10 12

12 14

13 15

15 17

0% - 100%

DIMMER FINE:0% - 100% 000-255

11 13

DIMMER MODES:StandardStageTVArchitecturalTheatreStage 2DIMMER DELAY TIME0.1Sec.0.2Sec.0.3Sec.0.4Sec.0.5Sec.0.6Sec.0.7Sec.0.8Sec.0.9Sec.1.0Sec.1.5Sec.2.0Sec.3.0Sec.4.0Sec.5.0Sec.6.0Sec.7.0Sec.8.0Sec.9.0Sec.10Sec.Default to Unit Setting

000-020021-040041-060061-080081-100101-120

14 16

121122123124125126127128129130131132133134135136137138139140

141-255



Functions16 Channels 18 Channels ValuesLED REFRESH RATE & SPECIAL FUNCTIONS:Default LED Refresh Rate 1200HzRefresh Rate (Hz)9009109209309409509609709809901000101010201030104010501060107010801090110011101120113011401150116011701180119012101220123012401250126012701280129013001310132013301340135013601370138013901400

000-010011-078

16 18

1112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960



Functions16 Channels 18 Channels ValuesLED REFRESH RATE & SPECIAL FUNCTIONS:1410142014301440145014601470148014901500250040005000600010,00015,00020,00025,000Disable LED Refresh RateEnable Blackout with Pan/Tilt MovementDisable Blackout with Pan/Tilt MovementEnable Blackout with Color ChangeDisable Blackout with Color ChangeEnable Blackout with Gobo ChangeDisable Blackout with Gobo ChangePan/Tilt ResetFocus ResetEffect ResetShutter ResetInternal Program 1 (Scenes 1-8)Internal Program 2 (Scenes 9-16)Internal Program 3 (Scenes 17-24)Internal Program 4 (Scenes 25-32)Internal Program 5 (Scenes 33-40)Internal Program 6 (Scenes 41-48)Internal Program 7 (Scenes 49-56)No Function

16 18

61626364656667686970717273747576777879

080-089090-099100-109110-119120-129130-139140-149150-159160-169170-179180-189190-199200-209210-219220-229230-239240-249250-255

SOFTWARE UPDATE - DMX Values 250-255 Updated in Software Version >1.0.4 Reset All250-25516 18


SYSTEM MENUThe fixture includes an easy to navigate system menu control panel display where all necessary settings and adjustments are made. (See image below) During normal operation, pressing the MODE button once will access the fixture’s main menu. Once in the main menu, you can navigate through the different menus and the sub-menus with the UP and DOWN buttons. When you reach a field that requires adjusting, press the ENTER button to access that field and use the UP, DOWN, LEFT or RIGHT buttons (depending on the sub menu) to adjust the field. Pressing the ENTER button once more to confirm your setting. You may exit the main menu at any time without making any adjustments by pressing the MODE button. To access the system menu when the fixture is not powered using the internal battery, press and hold the MODE button to illuminate the LCD screen until the DMX address is displayed. Then navigate to the desired system menu.

Focus Beam LED System Menu

FOCUS BEAM LED

LCD CONTROL PANEL LOCKOUTWhen the Key Lock function is activated, the control panel will automatically lock after the time set under the SCREEN SAVER DELAY submenu.When the Key Lock function is set to ON, the control panel will lock and the display will show “Un-lock” at the bottom of the display. Press and hold the MODE button for 3 seconds to unlock.

When the Key Lock function is set to ON1, the control panel will lock and the display will show “Unlock” at the bottom of the display. To unlock the display follow these steps:

1. Press the UP button, and the display will show *.

2. Press the DOWN button, and the display will show **.

3. Press the UP button, and the display will show ***.

4. Press the DOWN button, and the display will show ****.

5. Press the ENTER buttton, to confirm. If the button sequence was entered correctly, the display and control panel will unlock. If the button sequence was entered incorrectly, the display will return to the DMX addess display.



DMX SETTINGS001-XXX

Pan/Tilt Movement Feedback

DMX Lost StatusDMX Channel Mode SelectionDMX Addressing

16Ch / 18Ch

MENU OPTIONS DESCRIPTIONSUBMENU

Pan/Tilt Movement Speed

Reverse Tilt Motion

Set AddressDMX Channel ModeNo DMX Status Hold Last / Blackout / Manual

PERSONALITY

Status Settings

MANUAL CONTROL

Pan Invert: ON / OFF

Tilt Invert: ON / OFF

P./T. Feedback: ON / OFF

P./T. Speed: Speed 1 / Speed 2Hibernation: Off / 01M~99M / 15M

Manual Control Settings

Reverse Pan Motion

Sleep Setting (No Activity)

PanPan FineTiltTilt Fine Color Gobo Prism 1 Prism 1 Rot. Prism 2 Prism 2 Rot. Shutter Dimmer Dimmer Fine Focus Frost Dim Modes P/T Speed Special Function

Fan Settings Head Fan: Auto / High / Silent (Low)

Reset Motors

Reset All Motors: YES / NO

Pan/Tilt Reset: YES / NO

Effect Reset: YES / NO

Reset All Motors

Reset the Pan & Tilt Motors

Reset the Effect Motor

Dim Modes Dimming Curve ModesDimming Speed

Standard/Stage/TV/Architectur/Theatre/Stage2Dim Speed: 0.1-0.9s ~ 1-10s

LED Refresh Rate 1200 / 900-1500 / 2500 / 4000 / 5000 / 600010000 / 15000 / 20000 / 25000 (Hz)

LED Refresh Setting

Gamma 1.0 / 2.0 / 2.2 / 2.4 / 2.6 / 2.8 Gamma Brightness

Display

Intensity: 1~10 (Dimmest-Brightest)

Display Invert: YES / NO

Screen Saver Delay: OFF~10M

Display Intensity Adjustment

Display Inversion

Display Shutoff Time

Fan Speed Setting

Key Lock: OFF / ON / ON1 Display Control Lock

Shutter Reset: YES / NO Reset the Shutter Motor

ServiceUSB Port Power: ON / OFF

Update Software: YES / NO

Factory Restore: YES / NO(Pass Code = 11)

Calibration Adjustment

USB Port Activation

Software Update

Restore Factory Settings

Pass Code = 050

Effect Adjust (Calibration)(Pass Code = 50)

000-255000-255000-255 000-255 000-255000-255000-255 000-255 000-255 000-255 000-255000-255 000-255 000-255 000-255000-255 000-255 000-255

Software Version <V1.0.3



DMX SETTINGS001-XXX

Pan/Tilt Movement Feedback

DMX Lost StatusDMX Channel Mode SelectionDMX Addressing

16Ch / 18Ch


Pan/Tilt Movement Speed

Reverse Tilt Motion

Set AddressDMX Channel ModeNo DMX Status Hold Last / Blackout / Manual

PERSONALITY

Status Settings

MANUAL CONTROL

Pan Invert: ON / OFF

Tilt Invert: ON / OFFP./T. Feedback: ON / OFF

P./T. Speed: Speed 1 / Speed 2Hibernation: Off / 01M~99M / 15M

Manual Control Settings

Reverse Pan Motion

Sleep Setting (No Activity)

PanPan FineTiltTilt Fine Color Gobo Prism 1 Prism 1 Rot. Prism 2 Prism 2 Rot. Shutter Dimmer Dimmer Fine Focus Frost Dim Modes P/T Speed Special Function

Fan Settings Head Fan: Auto / High / Silent (Low)

Reset Motors

Reset All Motors: YES / NO

Pan/Tilt Reset: YES / NO

Effect Reset: YES / NO

Reset All Motors

Reset the Pan & Tilt Motors

Reset the Effect Motor

Dim Modes Dimming Curve ModesDimming Speed

Standard/Stage/TV/Architectur/Theatre/Stage2Dim Speed: 0.1-0.9s ~ 1-10s

LED Refresh Rate 1200 / 900-1500 / 2500 / 4000 / 5000 / 600010000 / 15000 / 20000 / 25000 (Hz)

LED Refresh Setting

Dim Curve Linear / Square / Inverse Square / S-Curve Set Dimming Curve

Display

Intensity: 1~10 (Dimmest-Brightest)

Display Invert: YES / NO

Screen Saver Delay: OFF~10M

Display Intensity Adjustment

Display Inversion

Display Shutoff Time

Fan Speed Setting

Key Lock: OFF / ON / ON1 Display Control Lock

Shutter Reset: YES / NO Reset the Shutter Motor

ServiceUSB Port Power: ON / OFF

Update Software: YES / NO

Factory Restore: YES / NO(Pass Code = 11)

Calibration Adjustment

USB Port Activation

Software Update

Restore Factory Settings

Pass Code = 050

Effect Adjust (Calibration)(Pass Code = 50)

000-255000-255000-255 000-255 000-255000-255000-255 000-255 000-255 000-255 000-255000-255 000-255 000-255 000-255000-255 000-255 000-255

Pan Degree: 630 / 540 Pan Degree Selection

Software Version >V1.0.4



INFORMATION


Fixture Life Time

Total LED Time

Fixture Temps

Total Running Time(Not Resettable) Total Running Time (Resettable)

Reset Total Running Time

Total LED On Running Time (Not Resettable) LED On Running Time (Resettable)

Reset LED Running Time

Fan Info. (RPM) LED Fan: XXXX LED Fan Speed

INTERNAL PROGRAMS

Program 1Program 2Program 3Program 4Program 5Program 6Program 7

Program 1 with AdjustmentsProgram 2 with AdjustmentsProgram 3 with AdjustmentsProgram 4 with AdjustmentsProgram 5 with AdjustmentsProgram 6 with AdjustmentsProgram 7 with Adjustments

Speed: 000~255 Fade: 000~255Speed: 000~255 Fade: 000~255Speed: 000~255 Fade: 000~255Speed: 000~255 Fade: 000~255Speed: 000~255 Fade: 000~255Speed: 000~255 Fade: 000~255Speed: 000~255 Fade: 000~255

Reset LED Temperature(Max Resettable)

Reset Lamp Temp: YES / NO (Pass Code = 050)

Current Head Temperature

Maximum Temperature(1) Reached (Resettable)(See Note 1)

Maximum Temperature(2) Reached (Not Resettable)(See Note 2)

LED’s

Current: XXX ˚F / XXX ˚C

Max Resettable: XXX ˚F / XXX ˚C

Max Not Resettable: XXX ˚F / XXX ˚C

Power On Time: XXXXXX Hours

P-On Time-R: XXXXXX Hours

P-On Time-Reset: YES / NO Pass Code = 50

LED On Time: XXXXXX Hours

LED On Time-R: XXXXXX Hours

LED Hours Reset: YES / NO Pass Code = 50

Error LogsFixture Errors

Reset Error Log - Pass Code = 50

List of Errors (One by One)

Clear the Error LogSoftware Version X.XX Current Software Version

DMX Values(3)(See Note 3)

Pan / Pan Fine / Tilt / Tilt Fine / Color / Gobo /Prism 1 / Prism 1 Rot / Prism 2 / Prism 2 Rot /Dimmer / Dimmer Fine / Focus / Frost / Dim Modes / P/T Speed / Special Function

Current DMX Values

Notes:(1) Current Maximum Temperature - Maximum fixture temp. that has been recorded, before reset and after reset.(2) Maximum Temperature - Overall maximum fixture temp. that has been recorded. (Not Resettable)(3) DMX Value options depend on the current DMX Channel mode setting.


Focus Beam LED System MenuDMX SETTINGS - The submenus listed under DMX SETTINGS are as follows: Set Address, DMX Channel Mode, and No DMX Status. - SET ADDRESS - In this submenu you can find and set your desired DMX address.

- DMX CHANNEL MODE - In this submenu you can find and set your desired DMX channel mode.

- NO DMX STATUS - This submenu setting is used as a precaution mode in case the DMX signal is lost or interrupted. The operating mode chosen in this submenu is the running mode the fixture will go into when the DMX signal is lost. Listed below are the 3 modes. • Hold Last - This setting will have the fixture stay in the last DMX setup. • Blackout - This setting will have the fixture automatically go into stand by mode. • Manual - This setting will go into the current manual control set up. See MANUAL CONTROL.

PERSONALITY - The submenus listed under PERSONALITY are as follows: Status Settings, Fan Settings, Dim Modes, LED Refresh Rate, Gamma, Reset Motors, Display, and Service. - STATUS SETTINGS - In this submenu you are able to access and adjust/change: Pan Degree, Pan Invert, Tilt Invert, P./T. Feedback, P./T. Speed, and Hibernation. NOTE: Pan Degree Added with software version >1.0.4

- FAN SETTINGS - In this submenu you are able to select your desired fan speed setting.

- DIM MODES - In this submenu you are able to select your desired dimmer mode and adjust the dimming speed time.

- LED REFRESH RATE - In this submenu you are able to select your desired LED refresh rate.

- GAMMA - In this submenu you are able to select your desired gamma setting. NOTE: Remove from software version <1.0.3.

- DIM CURVE - In this submenu you are able to select your desired dimmer curve setting. NOTE: Added with software version >1.0.4

- RESET MOTORS - In this submenu you are able to reset selected motors.

- DISPLAY - In this submenu you you are able to adjust the display intensity, invert the display, activate the display blackout, and activate/deactivate the display lock.

- SERVICE - In this submenu you are able to access and adjust/change: the calibration (effect adjust), activate the service port, update software, and restore the factory settings.

MANUAL CONTROL - This menu is for manual testing and manual control. Pan, tilt, color wheel, gobo wheel, prism 1, prism 1 rotation, shutter, dimmer, focus, frost can all be tested/adjusted. NOTE: The Prism and Frost features CANNOT be used at the same time.


Focus Beam LED System MenuINTERNAL PROGRAMS - In this menu you are able to select 1 of 7 internal programs to run. Program running speed and fade speed are adjustable.

INFORMATION - The submenus listed under INFORMATION are as follows: Fixture Life Time, Total LED Time, Fixture Temps, Fan Info. (RPM), DMX Values, Error Logs, and Software Version. - FIXTURE LIFE TIME • Power On Time -The TOTAL power ON running time of the unit is displayed. This time CANNOT be reset. • P-On Time-R - The CURRENT power ON running time of the unit is displayed. This running time may not be the same as the total power ON running time displayed under “Power On Time”. This time CAN be reset. NOTE: The displayed time represents the current power ON time since the last reset. • P-On Time-Reset - Reset the CURRENT power ON running time that is displayed under “P-On Time-R”.

- TOTAL LED TIME • LED On Time - The TOTAL LED ON time is displayed. This total LED ON time CANNOT be reset. NOTE: The displayed time represents the TOTAL LED ON time. • LED On Time-R - The CURRENT LED ON running time is displayed. This running time may not be the same as the total LED ON time displayed under “LED On Time”. This total LED ON time CAN be reset. NOTE: The displayed time represents the current LED ON time since the last reset. • LED On Time Reset - With this function you can reset the CURRENT LED ON time that is displayed under “LED On Time-R”.

- FIXTURE TEMPS • LED - The current temperature of the LED is displayed. • Reset LED Temp - Reset the LED temperature reading.

- FAN INFO. (RPM) - In this submenu the current fan speed will be displayed.

- DMX VALUES - Displays the DMX values of any DMX channel that is currently in use. NOTE: DMX value options depend on the current DMX channel mode setting.

- ERROR LOGS - In this submenu you are able to check any unit errors as well a clearing the error log. - SOFTWARE VERSION - Current software version is displayed.


Focus Beam LED Master-Slave Set UpMaster-Slave Configuration: This function will allows you to link units together to run in a Master-Slave set-up. In a Master-Slave set up one unit will act as the controlling unit and the others will react to the controlling units built-in programs. Any unit can act as a Master or as a Slave however, only one unit can be programmed to act as the “Master.” Master-Slave Connections and Settings:1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data cables to link your units together. Remember that the Male XLR connector is the input and the Female XLR connector is the ouput. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only. 2. Set the “Master” unit to your desired mode of operation. 3. Connect the first “Slave” unit to the “Master.”4. Set the “Slave” unit(s) to DMX control.


Focus Beam LED Dimmer Mode Chart

DIMMER

100%

50%

10%

0%Time (ms)

0 Sec

255 255

0 0

Standard (default) 0 0 0 0Stage 780 1100 1540 1660TV 1180 1520 1860 1940Architectural 1380 1730 2040 2120Theatre 1580 1940 2230 2280Stage 2 0 1100 0 1660

Rise Time (ms) Down Time (ms) Rise Time (ms) Down Time (ms)

Rise Time Down Time

Dimming CurveRamp Effect

0 sec Fade Time 1 sec Fade Time

Focus Beam LED Dimmer Curve Chart

Out

put

0

100%

Out

put

0

100%

Out

put

0

100%

Out

put

0

100%

DMX % DMX % DMX % DMX %LINEAR SQUARE INVERSE SQUARE S-CURVE


Focus Beam LED Dimensional Drawing

8.34” / 212mm

10.96” / 278.61mm

17.6

1” /

447.

3mm

11.1

02” /

282

mm

3.67

6” /

93.3

6mm14

” / 3

55.9

5mm

7.55” / 191.81mm

6.85” / 174mm10.96” / 278.61mm3.543” / 90mm

4.21

3” /

107m

m6.

850”

/ 17

4mm

Focus Beam LED Static Gobos

OPEN GOBO 1 GOBO 2 GOBO 3 GOBO 4 GOBO 5 GOBO 6

GOBO 7 GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 12 GOBO 13 GOBO 14


Focus Beam LED Trouble Shooting

Focus Beam LED Cleaning

Listed below are a few common problems the user may encounter, with solutions.Unit not responding to DMX:1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be car-ried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.2. Clean the external optics with glass cleaner and a soft cloth every 20 days.3. Always be sure to dry all parts completely before plugging the unit back in.Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog resi-due, dust, dew).

Focus Beam LED Multiple Unit Power LinkingWith this feature you can connect the fixtures to one another using the power cable input and output sockets. NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES AS THE POWER CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON THIS FIXTURE! CHECK SILK SCREEN FOR MAX AMPS.

Focus Beam LED Fuse ReplacementUnplug the unit from any power source it may be connected to. Once the power has been disconnected, use a flat head screw driver to unscrew the fuse holder located next to the powerCON input. Remove the bad fuse and replace with a new one, and screw the fuse holder back in.


Focus Beam LED Limited Warranty (USA Only) MANUFACTURER’S LIMITED WARRANTYA. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing

defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or

replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect.

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to ADJ Products, LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS: • Non L.E.D. Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps)

• Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month limited warranty)

• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding batteries which have a 180 day limited warranty). Note: 2 Year Warranty only applies to purchases within the United States.

• StarTec Series = 1 Year Limited Warranty (excluding batteries which have a 180 day limited warranty). • ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty


Focus Beam LED Specifications

Model: Focus Beam LED Voltage: 100V ~ 240V/50~60Hz LEDs: 1 x 80W Cool White LED Color Temperature: 7400K Working Position: Any safe working position Power Draw: 136W Fuse: 2A Dimensions: 10.96” (L) x 7.55” (W) x 17.61” (H) 278.61 x 191.8 x 447.3mm Weight: 27lbs. / 12.25 kgs Colors: 13 Colors + White Gobos: 14 Static Gobos + Open Prisms: 8 Facet Circular & 6 Facet Linear DMX Channels: 2 DMX Modes: 16 / 18 Warranty: 2 Year (730 days)

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without notice.

focus beam led - amazon web servicesadjmedia.s3-website-eu-west-1.amazonaws.com/manuals/adj focus...

Documents