flowserve men end-suction water pumps product …turbofluid.co.za/images/pdf/new/durco - men end...

Experience In Motion

MENEND-SUCTION WATER PUMPS Product Reference Manual

FPD-1210

(FPD-1209) Binder.indd 1(FPD-1209) Binder.indd 1 6/2/08 3:46:59 PM6/2/08 3:46:59 PM

Type MEN End-Suction Water Pump

Pumps

MEN Index

12/08FPD-1210a

Index Section

Product Summary and Description ................................................ 1

Standard and Optional Construction .............................................. 2

Pump Features and Benefits .......................................................... 3

Product Brochure ........................................................................... 4

Product Presentation ..................................................................... 5

Pump Cross Sectional Drawings ................................................... 6

General Arrangement Drawings ..................................................... 7

Engineering Data ............................................................................ 8

Standard Lead Times ..................................................................... 9

Typical Specifications ................................................................... 10

Typical Applications ..................................................................... 11

Representative Installation Lists .................................................. 12

Competitive Analysis .................................................................... 13

Coverage Charts ........................................................................... 14

Pump Selection Program Guidelines ........................................... 15

Drivers, Mechanical Seals and Accessory Information ................ 16

Optional and Alternative Configurations ....................................... 17

Aftermarket and Recommended Spare Parts ............................... 18

FAQs (Frequently Asked Questions) ............................................. 19

Typical Instruction Manual ........................................................... 20

Submittal Documentation (Software) ......................................... 21

Testing Capabilities ...................................................................... 22

Pricing for Pumps, Parts and Accessories................................... 23

Terms and Conditions .................................................................. 24


Property of FlowservePRIVATE AND CONFIDENTIAL

12/08ii

This page intentionally blank

Pumps

Type MEN



Pumps

MEN Summary and Description

12/081-1 Type MEN End-Suction Water Pump


Summary and DescriptionThe MEN family of single stage, end-suction water pumps provides a broad range of hydraulic coverage and low total cost of ownership. This family of pumps delivers maximum mechanical and hydraulic flexibility. Available in both frame mounted and close coupled configurations, the MEN family of pumps is ruggedly designed to provide long, reliable performance in a variety of water services.

The rugged and reliable MEN end-suction water pump is the preferred choice for general purpose water applications. The dependable MEN promotes parts interchangeability among pump sizes and configurations. The resulting reduction in inventory costs, along with the MEN’s optimal hydraulics and minimal maintenance needs, provides users with significant cost savings.

SpecificationsMEN water pumps destined for Europe are CE marked and comply with the dimensional requirements of the latest editions of EN 733 and DIN 24 255.

Horizontal end suction single stage, centrifugal water pump•Center line discharge•Foot supported back pull-out design•Single volute•Cast iron material•Usage for water, clear, non-abrasive and non-corrosive liquids•Designed for 50 Hz and 60 Hz•Extension to large capacity: refer to ME, DS, FRBH•Extension to higher pressure: refer to MHP•Pump rotation is clockwise when viewed from the motor end•Maximum working pressure at discharge •

16 bars (232 psi) –Maximum working pressure at suction•

10 bars (145 psi) –Maximum pumped fluid temperature•

Gland packing ≤ 105°C (221°F) –Mechanical seal ≤ 120°C (248°F) –

Minimum pumped fluid temperature: -10°C (14°F)•Maximum ambient temperature: 40°C (104°F)•Maximum solid suspension: 50 g/m• 3 (0.003 lbm/ft3)Density: 1•Viscosity: 1 mm• 2/s (31 SSU)Rotation speed (frequency 50 Hz)•

MEN: 1450/min –MEN: 2900/min –

Rotation speed (frequency 60 Hz)•MEN: 1750 (or) 3500/min –

CasingSingle volute, end suction, center line discharge, vertically split•Foot supported•Back pull-out•16 bars (232 psi) working pressure•21 bars (305 psi) test pressure•Cast iron•EMA: raised PN10/PN16 flanges•North America: raised face ANSI 125/ANSI 250 flanges•

ShaftStainless steel 13% chromium for high mechanical resistance•Shaft without sleeve under mechanical seal •

ImpellersRadial flow impeller•Impellers hydraulically balanced (except for the ones with Ø 125)•Shrouded impeller with an optimum hydraulic design to •guarantee high performanceKeyed on shaft•Locked by self locking nut•Cast iron or bronze•

SealsSingle unbalanced mechanical seal as standard•Cartridge mechanical seal (optional)•Gland packing (optional)•

BearingsCast iron bearing frame•Integral bearing housing•3 bearing frames to cover the whole MEN range:•

Frame 24: diameter 24 (0.95 in.) at coupling –Frame 32: diameter 32(1.26 in.) at coupling –Frame 42: diameter 42 (1.65 in.) at coupling –

Radial ball bearing 6300 series, sealed for life with •grease lubricationPump side bearing is protected by thrower•Bearing support foot: it minimizes the effects of external strains •on all the MEN sizes

PUMP TYPEImpeller diameter in mm

125 160 200 250 315 400

50-32

65-40 Bearing size

65-50 24

80-65

100-80 Bearing size

125-100 32

150-125 Bearing size

200-150 42Pumps at 1450 rpm

Pumps

MEN Summary and Description



Bearing HousingIntegral one-piece bearing housing in cast iron•

ThrowerRubber, mounted on shaft to protect bearing•

CouplingsSemi-flexible with elastomer insert•Spacer or other types if requested•Balanced couplings•

Auxiliary ConnectionsDraining and filling plugs•

BaseplatesThe standard steel baseplate provides the necessary rigidity and •exceptional vibration dampingCast iron baseplate on request•

Coupling GuardThermoplastic material, split design•Fully enclosed in accordance with CE rules•

Open Seal ChamberIntegral vortex breaking ribs to extend life of mechanical seal•



Pumps

MEN Standard and Optional Construction

Standard and Optional Seal Arrangements

StandardFlowserve Type 220 internal elastomeric bellows mechanical seal

OptionalFlowserve ISC cartridge mechanical seal

PackingGraphite and PTFE



Pumps


North American Europe

Standard Construction Optional Construction

MechanicalSeal

FlangesPN10/PN16

GlandPacking

Flanges Drilling Wear RingsANSI 125* ANSI 250

2 x 1-1/4 x 5 50-32-125 YES YES YES YES YES YES



2 x 1-1/4 x 8L 50-32-200L YES YES YES YES YES YES

2-1/2 x 1-1/2 x 5 65-40-125 YES YES YES YES YES YES

2-1/2 x 1-1/2 x 6 65-40-160 YES YES YES YES YES YES

2-1/2 x 1-1/2 x 8L 65-40-200L YES YES YES YES YES YES

2-1/2 x 1-1/2- x 10 65-40-250 YES YES YES YES YES YES

2-1/2 x 1-1/2 x 10L 65-40-250L YES YES YES YES YES YES

2-1/2 x 2 x 5 65-50-125 YES YES YES YES YES YES

2-1/2 x 2 x 6 65-50-160 YES YES YES YES YES YES

2-1/2 x 2 x 8L 65-50-200L YES YES YES YES YES YES

2-1/2 x 2 x 10L 65-50-250L YES YES YES YES YES YES





3 x 2-1/2 x 13L 80-65-315 YES YES YES YES YES YES

4 x 3 x 6 100-80-160 YES YES YES YES YES YES

4 x 3 x 8L 100-80-200L YES YES YES YES YES YES









6 x 5 x 10 150-125-250L YES YES YES YES YES YES





Standard / Optional Construction

Arnage

* With flanges ANSI 125: 13.8 bar (200 psi) max. up to 65°C (149°F)

12.1 bar (175.5 psi) max. to 66°C (151°F) up to 120°C (248°F)



Pumps


Standard / Optional Construction

Memphis (60 Hz)


Standard Construction Optional Construction

Mechanical Seal

Flanges ANSI 125*

GlandPacking

Flanges ANSI 250 Wear Rings

2 x 1-1/4 x 5 50-32-125 YES YES YES YES YES



2 x 1-1/4 x 8L 50-32-200L YES YES YES YES YES

2-1/2 x 1-1/2 x 5 65-40-125 YES YES YES YES YES

2-1/2 x 1-1/2 x 6 65-40-160 YES YES YES YES YES

2-1/2 x 1-1/2 x 8L 65-40-200L YES YES YES YES YES

2-1/2 x 1-1/2- x 10 65-40-250 YES YES YES YES YES

2-1/2 x 1-1/2 x 10L 65-40-250L YES YES YES YES YES

2-1/2 x 2 x 5 65-50-125 YES YES YES YES YES

2-1/2 x 2 x 6 65-50-160 YES YES YES YES YES

2-1/2 x 2 x 8L 65-50-200L YES YES YES YES YES

2-1/2 x 2 x 10L 65-50-250L YES YES YES YES YES





3 x 2-1/2 x 13L 80-65-315 YES YES YES YES YES

4 x 3 x 6 100-80-160 YES YES YES YES YES

4 x 3 x 8L 100-80-200L YES YES YES YES YES









6 x 5 x 10 150-125-250L YES YES YES YES YES





* With flanges ANSI 125: 13.8 bar (200 psi) max. up to 65°C (149°F)




Pumps


Materials of Construction with Various Applications

Standard Material Columns

DESCRIPTIONSTANDARD OPTIONS

Gland packing Mechanical seal Gland packing Mechanical seal

Casing Cast iron EN-GJL-250

Casing cover with stuffing box Cast iron EN-GJL-250

Wear Ring X30 Cr 13

Impeller Cast iron EN-GJL-250 Bronze Cu Sn 8

Bearing Housing Cast iron EN-GJL-250

Shaft X30 Cr 13

Gland packing Graphite PTFE

Mechanical seal Graphite CeramicSilicon Carbide Silicon Carbide

Material Comparison Table (near equivalent)

Selection of Construction Materials

AFNOR DIN AISI-SAE-ASTM

Cast iron EN-GJL-250 Grauguss GG 25 (DIN 1691) Class 35 grey cast iron

Bronze Cu Sn 8 G-Sn Bz 10 (DIN 1705) C90800-B427

Steel X30 Cr 13

13% Chromstahl (W.-Nr.1.4028)

AISI 420F

Stainless SteelX4CrNiMo16-5-1

Edelstahl (W.-Mr.1.4405)

Stainless Steel X2CrNiMoCuN25-6-3

Hochlegierten Edelstahl (W.-Nr.1.4517)

A890 Grade 1B

Water quality Casing Impeller Shaft Wear ring

Neutral clear water Cast iron Cast iron St. Steel -

Raw freshwater Cast ironCast iron or bronze

St. Steel St. Steel

Scaling water Cast iron Bronze St. Steel St. Steel

Slight corrosive water Cast iron Bronze St. Steel St. Steel

Sea water Limited usage

Cast iron Bronze St. Steel St. Steel

Treated water Cast iron Bronze St. Steel St. Steel



Pumps

MEN Pump Features and Benefits

Significant BenefitsMEN end-suction water pumps are engineered to provide significant benefits for users.

Superior pump performance•Low NPSHR –Quiet operation –Efficient operation –

Low total life cycle costs•Optimal hydraulic selection –Lower energy costs –Reduced inventory requirements –Reduced maintenance costs –Increased uptime –

Versatility•Multiple configurations –Parts interchangeability –



Pumps


Features and Benefits



Pumps


Item Feature Function Benefit

1 Dimensions and flanges – Compliance with DIN 24 255, NF EN 733– Interchangeability – Back pull-out

2 Casing and cover – 16 bar (232 psi) working pressure designed – Improvement of safety

3Impeller balancing chamber and balancing holes

– Minimized axial thrust – Improvement of bearings reliability

4 Hydraulic– Computer-aided designed– Impeller vanes curved in 2 axes– Increased nominal flow-rate: L hydraulics

– Excellent NPSH– Better efficiency– Flow rate above standard

5 Wear ring – Wear rings fitting for particular liquids – Maintenance cost reduced

6 Drain plug with gasket – Draining for shut-down periods– Frost resistance– Easy dismantling

7 Mounting foot – Machined holes – Ensure correct assembly

8 Shrouded impeller– Machined– Dynamically balanced

– Better efficiency– Improvement of bearings reliability

9 Casing cover – With anti-vortex ribs – Increases life of mechanical seal

10 Mechanical seal – Assembled in large casing cover– Good lubrication– Good reliability of sealing

11 Threaded connection – Evacuation, draining, filling – Easy fitting of pipes

12 Support foot – Steel rear support foot – Minimized effect of external constraints

13Deep-groove ball bearings(Series 6300)

– Large diameter– Life grease lubricated– Reinforced series

– Good bearing reliability

14 Shaft – Stainless steel 13% chromium– Corrosion resistant– High mechanical strength

15 Bearing housing– Single piece cast iron– Robust construction

– Improvement of unit rigidity and concentricity

16 Studs and nuts – Stainless steel– Easy setting of gland– Corrosion resistant

17 Gland packing – Graphite and PTFE – Less friction

18 Gasket – Synthetic and nitrile fibers – Easy removing

19 Filling plug – Filling the pump and priming – Easy for first start up

Features and Benefits

12/08Type MEN End-Suction Water Pump

3-4



Pumps


MENEnd-Suction Water Pump

MEN – MENBLOC

Experience In Motion

© TriCom, Inc., 2007, All Rights Reserved.

2

Pump Supplier To The WorldProduct Brands of Distinction

ACEC™ Centrifugal Pumps

Aldrich® Pumps

Byron Jackson® Pumps

Cameron® Pumps

Durco® Pumps

Flowserve® Pumps

IDP ® Pumps

Jeumont-Schneider™ Pumps

Pacific® Pumps

Pleuger ® Pumps

Scienco® Pumps

Sier-Bath® Rotary Pumps

TKL™ Pumps

United® Centrifugal Pumps

Western Land Roller ® Irrigation Pumps

Wilson-Snyder ® Pumps

Worthington ® Pumps

Worthington Simpson® Pumps

Flowserve is the driving force in the global industrial pump marketplace. No other pump company in the world has the depth or breadth of expertise in the successful application of pre-engineered, engineered and special purpose pumps and systems.

Life Cycle Cost SolutionsFlowserve is providing pumping solutions which permit customers to reduce total life cycle costs and improve productivity, profitability and pumping system reliability.

Market Focused Customer SupportProduct and industry specialists develop effective proposals and solutions directed toward market and customer prefer-ences. They offer technical advice and assistance throughout each stage of the product life cycle, beginning with the inquiry.

Broad Product LinesFlowserve offers a wide range of complementary pump types, from pre-engineered process pumps, to highly engineered and special purpose pumps and systems. Pumps are built to recognized global standards and customer specifications.

Pump designs include:

Single stage processBetween bearing single stageBetween bearing multistageVerticalSubmersible motorRotaryReciprocatingNuclearSpecialty


MEN End-Suction Water Pump

3

The MEN family of single stage, end-suction water pumps provides a broad range of hydraulic coverage and low total cost of ownership. This family of pumps delivers maximum mechanical and hydraulic flexibility. Available in both frame-mounted and close-coupled configurations, the MEN family of pumps is ruggedly designed to provide long, reliable performance in a variety of water services.

Significant BenefitsMEN end-suction water pumps are engineered to provide significant benefits for users.

Superior pump performanceLow NPSHR –Quiet operation –Efficient operation –

Low total life cycle costsOptimal hydraulic selection –Lower energy costs –Reduced inventory requirements –Reduced maintenance costs –Increased uptime –

VersatilityMultiple configurations –Parts interchangeability –

ApplicationsWater supplyWater treatmentIrrigationDrainageFilter cleaningFire protectionGeneral industryWater circulationHVAC

Complementary Pump DesignsFlowserve also can provide the following complementary pump designs:

SMP standard motor pumpSMX non-metallic standard motor pumpFormed stainless steel pumpsCPX ISO chemical process pumpCPXV ISO vertical sump pumpMark 3 ANSI chemical process pumpESP2 vertical immersion sump pumpFRBH heavy-duty paper stock and process pumpME end-suction water pumpMHP frame-mounted, single volute, high- pressure pumpDS end-suction process pumpLR between bearings, axially split pump

flowserve.com


Rugged Construction, Reliable Performance

Mark 3

SMP

CPX

4

Volute Casing Design has raised face flanges to ISO PN 10/16 or ANSI B16.1 specifications

Precision Cast Closed Impeller with machined shrouds is dynamically balanced for high efficiency. Axial thrust is minimized by balancing chamber and holes on the rear side

Sturdy Bearing Housing incorporates greased-for-life, large diameter, reinforced ball bearings protected by thrower and covers

Open Seal Chamber features integral vortex breaking ribs to extend the life of mechanical seals. A 13% chromium steel sleeve is used with packing

Oversized Stainless Steel Shaft is conservatively designed to minimize deflection and reduce wear

Back Pull-Out Design facilitates inspection and maintenance

The rugged and reliable MEN end-suction water pump is the preferred choice for general purpose water applications. The dependable MEN promotes parts inter-changeability among pump sizes and configurations. The resulting reduction in inventory costs, along with the MEN’s optimal hydraulics and minimal maintenance needs, provides users with significant cost savings.

MEN water pumps destined for Europe are CE marked and comply with the dimensional requirements of the latest editions of EN 733 and DIN 24 255.

Operating ParametersFlows to 800 m3/h (3500 gpm)Heads to 140 m (450 ft)Pressures to 16 bar (230 psi)Temperatures from -10°C (15°F) to 140°C (280°F)Speeds to 3500 rpm

MEN End-Suction Water Pump


Lorem ipsum dolor sit amet, consect-etur

Adipscing elitsed diam nonnumy eius-mod tempor

Incidunt ut labore et dolore magna aliquam erat volupat

5

Elastomeric Bellows Mechanical SealThe MEN pump comes standard with an internal, elasto-meric bellows mechanical seal that is inexpensive and highly dependable. The bellow’s high strength and flexibil-ity iskey to the seal’s reliable performance in a wide range of applications. Bidirectional in operation, the seal readily accommodates misalignment, end-float and seal face wear. Furthermore, this design is widely used throughout the water industry, making spare parts readily available.

For those applications in which a mechanical seal is not needed, packing is also available with the MEN pump.

Optional Packed Gland

flowserve.com


MENBLOC Close-Coupled DesignMENBLOC is the close-coupled configuration of the MEN water pump. Not requiring a baseplate or coupling, it is an economical alternative to the frame-mounted MEN. Its reduced footprint also permits its use in tight areas.

MENBLOC pumps intended for use in Europe are CE marked. Wet-end components comply with the latest editions of the EN 733 and DIN 24 255.

Operating ParametersFlows to 340 m3/h (1500 gpm)Heads to 100 m (330 ft)Pressures to 16 bar (230 psi)Temperatures to 110°C (230°F)

6

Standard Description Gland Mechanical Options Packing Seal Casing Cast Iron

Casing Cover Cast Iron w/Stuffing Box

Wear Ring 13% Chromium Steel

Impeller Cast Iron or Bronze

Bearing Cast Iron Housing

Shaft 13% Chromium Other Chromium Steel Steel *

Shaft 13% Sleeve Chromium Steel

Gland Graphite Packing PTFE

Mechanical Graphite on Silicon Carbide on Seal Ceramic Silicon Carbide

Available ConfigurationsAvailable in 33 sizes, the MEN family of water pumps consists of multiple designs with varied hydraulic capabilities to meet application needs. They include the following configurations:

MEN frame-mounted standard water pumpMENBLOC close-coupled standard water pump MEN-SP cantilever sump pumpMEN-TI diesel-driven fire pump

Options to Suit Application NeedsISO or ANSI flangesGrease lubricated bearingsCasing wear ringsPacking or mechanical seal

Options and Technical Data


Flow Rate - 50 Hz

TDH

- 50 H

z

m3/h

gpm

m

ft500400300

200150

100

70

504030

2015

10

7

1008060504030

20

108654

3

2

mft

500400300

200150

100

70

504030

2015

10z

200

1008060504030

20

108654

3

20 30 50 70 100 200 300 500 1000 2000 5000

3 4 5 6 8 10 20 30 40 50 100 200 500 1000

m3/h

gpm 20 30 50 70 100 200 300 500 1000 2000 5000

3 4 5 6 8 10 20 30 40 50 100 200 500 1000

TDH

- 60 H

z

Flow Rate - 60 Hz

MEN 2 pole

MEN 4 pole

MEN Range Chart

Materials of Construction

* Consult factory or Flowserve representative

flowserve.com

Global Service and Technical Support

7

Life Cycle Cost Solutions

1 While exact values may differ, these percentages are consistent with those published by leading pump manufacturers and end users, as well as industry associations and government agencies worldwide.

2%

44% 17%

12%

16%9%

Energy

Maintenance and Repair

Loss of Production

Purchase and Installation

Operational

Decontamination and Removal

Innovative Life Cycle Cost Solutions

Operating ExpensesEnergy consumptionMaintenanceProduction lossesEnvironmentalInventoryOperatingRemoval

Typically, 90% of the total life cycle cost (LCC) of a pumping system is accumulated after the equipment is purchased and installed. Flowserve has developed a comprehensive suite of solutions aimed at providing customers with unprecedented value and cost savings throughout the life span of the pumping system. These solutions account for every facet of life cycle cost, including:

Capital ExpensesInitial purchase Installation

Typical Pump Life Cycle Costs1

flowserve.com

USA and CanadaFlowserve Corporation5215 North O’Connor Blvd. Suite 2300Irving, Texas 75039-5421 USATelephone: 1 937 890 5839

Europe, Middle East, Africa Flowserve CorporationGebouw HagepointWestbroek 39-514822 ZX Breda NetherlandsTelephone: 31 76 502 8920

Latin America Flowserve CorporationBoulevard del Cafetal Edificio Ninina, Local 7 El Cafetal - Caracas Venezuela 1061 Telephone: 58 212 985 3092 Telefax: 58 212 985 1007

Asia Pacific Flowserve Pte. Ltd.200 Pandan Loop #06-03/04Pantech 21Singapore 128388Telephone: 65 6775 3003Telefax: 65 6779 4607

To find your local Flowserve representative:

For more information about Flowserve Corporation,visit www.flowserve.com or call USA 1 800 728 PUMP (7867)

Bulletin PS-10-2d (E) Printed in USA. February 2008. © Flowserve Corporation




Pumps

MEN Presentation

Product PresentationInformation not provided



Pumps

MEN Presentation


Pumps

MEN Pump Cross Sectional Drawings



Pumps

MEN Pump Cross Sectional Drawings



Parts List

Item Designation

1110 Pump casing

1221-01 Casing cover with stuffing box

1221-02 Casing cover with mechanical seal

1500 Wear ring

2110 Pump shaft

2250 Radial flow impeller

2540 Thrower

2905 Plain washer

3011 Radial ball bearing

3134 Support foot

3200 Bearing housing

3260 Bearing cover

4120 Gland

4130 Gland packing

4131 Follower

4200 Mechanical seal

4590-01 Gasket

4590-02 Gasket

4590-03 Gasket

4595 Grommet

6511 Priming plug

6515 Drain plug

6544 Circlip

6570 End-shaft screw

6572 Stud

6577-01 Hexagon bolt



6581 Hexagon nut

6700-01 Key

6700-02 Key

9331 Optional Cover plate


3 x 2-1/2 x 10L 80-65-250L

3 x 2-1/2 x 13L 80-65-315

4 x 3 x 8L 100-80-200L

4 x 3 x 10L 100-80-250L

4 x 3 x 13 100-80-315

5 x 4 x 8L 125-100-200L

5 x 4 x 10L 125-100-250L

5 x 4 x 13 125-100-315

5 x 4 x 13L 125-100-315L

6 x 5 x 10L 150-125-250L

5 x 4 x 16 125-100-400

5 x 4 x 16L 125-100-400L

6 x 5 x 13L 150-125-315L

6 x 5 x 6L 150-125-400L

8 x 6 x 13L 200-150-315L

8 x 6 x 16L 200-150-400L


3 x 2-1/2 x 10L 80-65-250L

4 x 3 x 8L 100-80-200L

4 x 3 x 10L 100-80-250L

5 x 4 x 8L 125-100-200L

5 x 4 x 10L 125-100-250L

5 x 4 x 8L 125-100-315L

6 x 5 x 10L 150-125-250L


2 x 1-1/4 x 5 50-32-125

2 x 1-1/4 x 6 50-32-160

2-1/2 x 1-1/2 x 5 65-40-125

2-1/2 x 1-1/2 x 6 65-40-160

2-1/2 x 2 x 5 65-50-125

3 x 2-1/2 x 5 80-65-125

4 x 3 x 8L 100-80-200L

5 x 4 x 8L 125-100-200L


2 x 1-1/4 x 5 50-30-1252-1/2 x 1-1/2 x 5 65-40-1252-1/2 x 2 x 5 65-50-125

3 x 2-1/2 x 5 80-65-125

IMPELLER DIAMETER 125Without back hub ring(MEN pumps)

Packed Box

Clamped Casing Cover

With Wear Rings

2250

6577-02

1500



Pumps

MEN General Arrangement Drawings

ARNAGE (50 Hz) – PN10/PN16Bare Pump

North American Europe DNA DNR a f h1 h2 b m1 m2 n1 n2 s1 p d l t u w m4 s2 k o r X kg

2 x 1-1/4 x 5 50-32-125

50 32 80 360

112 140

50 100 70

190 140

1512

24 50 27 8 260 43 14 1/4 3/8 1/4 100

31

2 x 1-1/4 x 6 50-32-160 132 160

240 190

35

2 x 1-1/4 x 8 50-32-200160 180

43

2 x 1-1/4 x 8L 50-32-200L 14 43

2-1/2 x 1-1/2 x 5 65-40-125

65 40

80

360

112 140

50 100 70

210 160

15

12

24 50 27 8 260 43 14 1/4 3/8 1/4 100

34

2-1/2 x 1-1/2 x 6 65-40-160 132 160 240 190 36

2-1/2 x 1-1/2 x 8L 65-40-200L

100

160 180 265 212

14

45

2-1/2 x 1-1/2- x 10 65-40-250180 225 65 125 95 320 250

60

2-1/2 x 1-1/2 x 10L 65-40-250L 60

2-1/2 x 2 x 5 65-50-125

65 50 100 360

132 160

50 100 70

240 190

15

12

24 50 27 8 26043

14 1/4 3/8 1/4 100

35

2-1/2 x 2 x 6 65-50-160160

180265 212

14

45

2-1/2 x 2 x 8L 65-50-200L 200 49

2-1/2 x 2 x 10L 65-50-250L 180 225 65 125 95 320 250 44 60

3 x 2-1/2 x 5 80-65-125

80 65100

360160

180

65 125 95280 212

15 14 24 50 27 8 26043

14

1/4 3/8 1/4 100

39

3 x 2-1/2 x 6 80-65-160 200 49

3 x 2-1/2 x 8L 80-65-200L 180 225 320 250 44 53

3 x 2-1/2 x 10L 80-65-250L470

200 25080 160 120

360 28018 16 32 80 35 10 340 42 3/8 1/2 3/8 140

90

3 x 2-1/2 x 13L 80-65-315 125 225 280 400 315 115

4 x 3 x 6 100-80-160

100 80 125

360180

22565 125 95

320 25015 14

24 50 27 8 260 44

14

1/4 3/8 1/4 100 58

4 x 3 x 8L 100-80-200L

470

250 345 280

32 80 35 10 34042

3/8 1/2 3/8 140

78

4 x 3 x 10L 100-80-250L 200 28080 160 120 400 315 18 16

97

4 x 3 x 13 100-80-315 250 315 43 123

5 x 4 x 8L 125-100-200L

125 100

125

470

200280

80 160 120

360 280

18 16 32 80 35 10 340

42

14

3/8

1/2

3/8

140 90

5 x 4 x 10L 125-100-250L

140

225

400 315 43

150 106

5 x 4 x 13 125-100-315250 315 140

138

5 x 4 x 13L 125-100-315L 127

5 x 4 x 16 125-100-400530 280 355 100 200 150 500 400 22 20 42 110 45 12 370 44 1/2 1/2 160

185

5 x 4 x 16L 125-100-400L 187

6 x 5 x 10 150-125-250L

150 125 140

470 250355

80 160 120 400 315 18 16 32 80 35 10 340 43

14

3/8

1/2

3/8 150 130

6 x 5 x 13L 150-125-315L530

280100 200 150 500 400 22 20 42 110 45 12 370 42 1/2 1/2 160

180

6 x 5 x 6L 150-125-400L 315 400 218

8 x 6 x 13L 200-150-315L200 150 160 530

280 400100 200 150 550 450 22 20 42 110 45 12 370 42 14 1/2 1/2 1/2

160 209

8 x 6 x 16L 200-150-400L 315 450 180 238

Bare Pump Dimension Table – mm

DNA = Suction Nominal Diameter – DNR = Discharge Nominal DiameterNote: k, o, r = BSP thread For flange dimensions, see section § 8 CC. Flange Dimension Data PN10 / PN16



Pumps


Bare Pump Dimension Table – in

North American Europe DNA DNR a f h1 h2 b m1 m2 n1 n2 s1 p d l t u w m4 s2 k o r X lb

2 x 1-1/4 x 5 50-32-125

2 1-1/4 3.2 14.2

4.4 5.5

2.0 3.9 2.8

7.5 5.5

0.60.5

0.9 2.0 1.1 0.3 10.2 1.7 0.6 1/4 3/8 1/4 3.9

68

2 x 1-1/4 x 6 50-32-160 5.2 6.3

9.5 7.5

77

2 x 1-1/4 x 8 50-32-2006.3 7.1

95

2 x 1-1/4 x 8L 50-32-200L 0.6 95

2-1/2 x 1-1/2 x 5 65-40-125

2-1/2 1-1/2

3.2

14.2

4.4 5.5

2.0 3.9 2.8

8.3 6.3

0.6

0.5

0.9 2.0 1.1 0.3 10.2 1.7 0.6 1/4 3/8 1/4 3.9

75

2-1/2 x 1-1/2 x 6 65-40-160 5.2 6.3 9.5 7.5 79

2-1/2 x 1-1/2 x 8L 65-40-200L

3.9

6.3 7.1 10.4 8.4

0.6

99

2-1/2 x 1-1/2- x 10 65-40-2507.1 8.9 2.6 4.9 3.7 12.6 9.8

132

2-1/2 x 1-1/2 x 10L 65-40-250L 132

2-1/2 x 2 x 5 65-50-125

2-1/2 2 3.9 14.2

5.2 6.3

2.0 3.9 2.8

9.5 7.5

0.6

0.5

0.9 2.0 1.1 0.3 10.21.7

0.6 1/4 3/8 1/4 3.9

77

2-1/2 x 2 x 6 65-50-1606.3

7.110.4 8.4

0.6

99

2-1/2 x 2 x 8L 65-50-200L 200 108

2-1/2 x 2 x 10L 65-50-250L 7.1 8.9 2.6 4.9 3.7 12.6 9.8 1.7 132

3 x 2-1/2 x 5 80-65-125

3 23.9

14.26.3

7.1

2.6 4.9 3.711.0 8.4

0.6 0.6 0.9 2.0 1.1 0.3 10.21.7

0.6

1/4 3/8 1/4 3.9

86

3 x 2-1/2 x 6 80-65-160 7.9 108

3 x 2-1/2 x 8L 80-65-200L 7.1 8.9 12.6 9.8 1.7 117

3 x 2-1/2 x 10L 80-65-250L18.5

7.9 9.83.2 6.3 4.7

14.2 11.00.7 0.6 1.3 3.2 1.4 0.4 13.4 1.7 3/8 1/2 3/8 5.5

198

3 x 2-1/2 x 13L 80-65-315 4.9 8.9 11.0 15.8 12.4 253

4 x 3 x 6 100-80-160

4 3 4.9

14.27.1

8.92.6 4.9 3.7

12.6 9.80.6 0.6

0.9 2.0 1.1 0.3 10.2 1.7

0.6

1/4 3/8 1/4 3.9 128

4 x 3 x 8L 100-80-200L

18.5

9.8 13.6 11.0

1.3 3.2 1.4 0.4 13.41.7

3/8 1/2 3/8 5.5

172

4 x 3 x 10L 100-80-250L 7.9 11.03.2 6.3 4.7 15.8 12.4 0.7 0.6

214

4 x 3 x 13 100-80-315 9.9 12.4 1.7 271

5 x 4 x 8L 125-100-200L

5 4

4.9

18.5

7.911.0

3.2 6.3 4.7

14.2 11.0

0.7 0.6 1.3 3.2 1.4 0.4 13.4

1.7

0.6

3/8

1/2

3/8

5.5 198

5 x 4 x 10L 125-100-250L

5.5

8.9

15.8 12.4 1.7

5.9 234

5 x 4 x 13 125-100-3159.8 12.4 5.5

304

5 x 4 x 13L 125-100-315L 280

5 x 4 x 16 125-100-40020.9 11.0 14.0 3.9 7.9 5.9 19.7 15.8 0.9 0.8 1.7 4.3 1.8 0.5 14.6 1.7 1/2 1/2 6.3

408

5 x 4 x 16L 125-100-400L 412

6 x 5 x 10 150-125-250L

6 5 5.5

18.5 9.814.0

3.2 6.3 4.7 15.8 12.4 0.7 0.6 1.3 3.2 1.4 0.4 13.4 1.7

0.6

3/8

1/2

3/8 5.9 287

6 x 5 x 13L 150-125-315L20.9

11.03.9 7.9 5.9 19.7 15.8 0.9 0.8 1.7 4.3 1.8 0.5 14.6 1.7 1/2 1/2 6.3

397

6 x 5 x 6L 150-125-400L 12.4 15.8 481

8 x 6 x 13L 200-150-315L8 6 6.3 20.9

11.0 15.83.9 7.9 5.9 21.7 17.7 0.9 0.8 1.7 4.3 1.8 0.5 14.6 1.7 0.6 1/2 1/2 1/2

6.3 461

8 x 6 x 16L 200-150-400L 12.4 17.7 7.1 525

DNA = Suction Nominal Diameter – DNR = Discharge Nominal DiameterNote: k, o, r = BSP thread For flange dimensions, see section § 8 CC. Flange Dimension Data PN10 / PN16

ARNAGE (50 Hz) – PN10/PN16Bare Pump



Pumps


MEMPHIS (60 Hz) – ANSI 125 Bare Pump


2 x 1-1/4 x 5 50-32-125

2 1-1/4 3.07 14.17

4.41 5.39

1.97 3.94 2.76

7.48 5.51

0.590.47

0.94 1.97 1.06 0.31 10.24 1.69 0.55 1/4 3/8 1/4 3.94

68

2 x 1-1/4 x 6 50-32-160 520 6.18

9.45 7.48

77

2 x 1-1/4 x 8 50-32-2006.30 6.97

95

2 x 1-1/4 x 8L 50-32-200L 0.55 95

2-1/2 x 1-1/2 x 5 65-40-125

2-1/2 1-1/2

3.19

14.17

4.41 5.47

1.97 3.94 2.76

8.27 6.30

0.59

0.47

0.94 1.97 1.06 0.31 10.24 1.69 0.55 1/4 3/8 1/4 3.94

75

2-1/2 x 1-1/2 x 6 65-40-160 5.20 6.26 240 190 79

2-1/2 x 1-1/2 x 8L 65-40-200L

3.98

6.30 7.05 265 212

14

99

2-1/2 x 1-1/2- x 10 65-40-2507.09 8.82 2.56 4.92 320 250

132

2-1/2 x 1-1/2 x 10L 65-40-250L 132

2-1/2 x 2 x 5 65-50-125

2-1/2 2 3.98 14.17

5.20 6.22

1.97 3.94 2.76

9.45 7.48

0.59

0.47

0.94 1.97 1.06 0.31 10.241.69

0.55 1/4 3/8 1/4 3.94

77

2-1/2 x 2 x 6 65-50-1606.30

7.0110.43 8.35

0.55

45

2-1/2 x 2 x 8L 65-50-200L 7.80 49

2-1/2 x 2 x 10L 65-50-250L 7.09 8.78 2.65 4.92 3.74 12.60 9.84 1.73 60

3 x 2-1/2 x 5 80-65-125

3 2-1/24.02

14.176.30

7.13

2.56 4.92 3.7411.02 8.35

0.59 0.55 0.94 1.97 1.06 0.31 10.241.69

0.55

1/4 3/8 1/4 3.94

86

3 x 2-1/2 x 6 80-65-160 7.91 108

3 x 2-1/2 x 8L 80-65-200L 7.09 8.90 12.60 9.84 1.73 117

3 x 2-1/2 x 10L 80-65-250L18.50

7.87 9.803.15 6.30 4.72

14.17 11.020.71 0.63 1.26 3.15 1.38 0.39 13.39 1.65 3/8 1/2 3/8 5.51

198

3 x 2-1/2 x 13L 80-65-315 5.00 8.85 11.06 15.75 12.40 253

4 x 3 x 6 100-80-160

4 3 5.04

14.177.09

8.942.56 4.92 3.74

12.60 9.840.59 0.55

0.94 1.97 1.06 0.31 10.24 1.73

0.55

1/4 3/8 1/4 3.94 128

4 x 3 x 8L 100-80-200L

18.50

9.88 13.58 11.02

1.26 3.15 1.38 0.39 13.391.65

3/8 1/2 3/8 5.51

172

4 x 3 x 10L 100-80-250L 7.87 11.063.15 6.30 4.72 15.75 12.40 0.71 0.63

214

4 x 3 x 13 100-80-315 9.87 12.44 1.69 271

5 x 4 x 8L 125-100-200L

5 4

5.08

18.50

7.8711.14

3.15 6.30 4.72

14.17 11.02

0.71 0.63 1.26 3.15 1.38 0.39 13.39

1.65

0.55

3/8

1/2

3/8

5.51 198

5 x 4 x 10L 125-100-250L

5.67

8.86

15.75 12.40 1.69

5.90 234

5 x 4 x 13 125-100-3159.84 12.52 5.51

304

5 x 4 x 13L 125-100-315L 127

5 x 4 x 16 125-100-40020.87 11.02 14.09 3.94 7.87 5.90 19.68 15.75 0.87 0.79 1.65 4.33 1.77 0.47 14.57 1.73 1/2 1/2 6.30

408

5 x 4 x 16L 125-100-400L 187

6 x 5 x 10 150-125-250L

6 5 5.71

18.50 9.8414.09

3.15 6.30 4.72 15.75 12.40 0.71 0.63 1.26 3.15 1.38 0.39 13.39 1.69

0.55

3/8

1/2

3/8 5.90 287

6 x 5 x 13L 150-125-315L20.87

11.023.94 7.87 5.90 19.68 15.75 0.87 0.79 1.65 4.33 1.77 0.47 14.57 1.65 1/2 1/2 6.30

397

6 x 5 x 6L 150-125-400L 12.40 15.87 481

8 x 6 x 13L 200-150-315L8 6 6.50 20.87

11.02 15.943.94 7.87 5.90 21.65 17.72 0.87 0.79 1.65 4.33 1.77 0.47 14.57 1.65 0.55 1/2 1/2 1/2

6.30 461

8 x 6 x 16L 200-150-400L 12.40 17.91 7.09 525


3 x 2-1/2 x 8L 80-65-250L 3" 2-1/2" 4.02 21.06 7.87 9.88 3.15 6.30 4.72 14.17 11.02 0.71 0.63 1.65 4.33 1.77 0.47 13.78 1.65 0.55 3/8 1/2 3/8 6.30 212

5 x 4 x 8L 125-100-200L 5" 4" 5.08 21.26 7.87 11.14 3.15 6.30 4.72 14.17 11.02 0.71 0.63 1.65 4.33 1.77 0.47 13.78 1.65 0.55 3/8 1/2 3/8 6.30 212


DNA = Suction Nominal Diameter – DNR = Discharge Nominal Diameter

Note: k, o, r = NPT thread

Only for 60 Hz – 3600 RPM



Pumps


MEMPHIS (60 Hz) – ANSI 125Bare Pump


2 x 1-1/4 x 5 50-32-125

50 32 78 360

112 137

50 100 70

190 140

1512

24 50 27 8 260 43 14 1/4 3/8 1/4 100

31

2 x 1-1/4 x 6 50-32-160 132 157

240 190

35

2 x 1-1/4 x 8 50-32-200160 177

43

2 x 1-1/4 x 8L 50-32-200L 14 43

2-1/2 x 1-1/2 x 5 65-40-125

65 40

81

360

112 139

50 100 70

210 160

15

12

24 50 27 8 260 43 14 1/4 3/8 1/4 100

34

2-1/2 x 1-1/2 x 6 65-40-160 132 159 240 190 36

2-1/2 x 1-1/2 x 8L 65-40-200L

101

160 179 265 212

14

45

2-1/2 x 1-1/2- x 10 65-40-250180 224 65 125 95 320 250

60

2-1/2 x 1-1/2 x 10L 65-40-250L 60

2-1/2 x 2 x 5 65-50-125

65 50 101 360

132 158

50 100 70

240 190

15

12

24 50 27 8 26043

14 1/4 3/8 1/4 100

35

2-1/2 x 2 x 6 65-50-160160

178265 212

14

45

2-1/2 x 2 x 8L 65-50-200L 198 49

2-1/2 x 2 x 10L 65-50-250L 180 223 65 125 95 320 250 44 60

3 x 2-1/2 x 5 80-65-125

80 65102

360160

181

65 125 95280 212

15 14 24 50 27 8 26043

14

1/4 3/8 1/4 100

39

3 x 2-1/2 x 6 80-65-160 201 49

3 x 2-1/2 x 8L 80-65-200L 180 226 320 250 44 53

3 x 2-1/2 x 10L 80-65-250L470

200 25180 160 120

360 28018 16 32 80 35 10 340 42 3/8 1/2 3/8 140

90

3 x 2-1/2 x 13L 80-65-315 127 225 281 400 315 115

4 x 3 x 6 100-80-160

100 80 128

360180

22765 125 95

320 25015 14

24 50 27 8 260 44

14

1/4 3/8 1/4 100 58

4 x 3 x 8L 100-80-200L

470

251 345 280

32 80 35 10 34042

3/8 1/2 3/8 140

78

4 x 3 x 10L 100-80-250L 200 28180 160 120 400 315 18 16

97

4 x 3 x 13 100-80-315 250 316 43 123

5 x 4 x 8L 125-100-200L

125 100

129

470

200283

80 160 120

360 280

18 16 32 80 35 10 340

42

14

3/8

1/2

3/8

140 90

5 x 4 x 10L 125-100-250L

144

225

400 315 43

150 106

5 x 4 x 13 125-100-315250 318 140

138

5 x 4 x 13L 125-100-315L 127

5 x 4 x 16 125-100-400530 280 358 100 200 150 500 400 22 20 42 110 45 12 370 44 1/2 1/2 160

185

5 x 4 x 16L 125-100-400L 187

6 x 5 x 10 150-125-250L

150 125 145

470 250358

80 160 120 400 315 18 16 32 80 35 10 340 43

14

3/8

1/2

3/8 150 130

6 x 5 x 13L 150-125-315L530

280100 200 150 500 400 22 20 42 110 45 12 370 42 1/2 1/2 160

180

6 x 5 x 6L 150-125-400L 315 403 218

8 x 6 x 13L 200-150-315L200 150 165 530

280 405100 200 150 550 450 22 20 42 110 45 12 370 42 14 1/2 1/2 1/2

160 209

8 x 6 x 16L 200-150-400L 315 455 180 238


3 x 2-1/2 x 8L 80-65-250L 80 65 102 535 200 251 80 160 120 360 280 18 16 42 110 45 12 350 42 14 3/8 1/2 3/8 160 96

5 x 4 x 8L 125-100-200L 125 100 129 540 200 283 80 160 120 360 280 18 16 42 110 45 12 353 42 14 3/8 1/2 3/8 160 96







Pumps




2 x 1-1/4 x 5 50-32-125

2 1-1/4 3.25 14.17

4.41 5.55

1.97 3.94 2.76

7.48 5.51

0.590.47

0.94 1.97 1.06 0.31 10.24 1.69 0.55 1/4 3/8 1/4 3.94

68

2 x 1-1/4 x 6 50-32-160 520 6.34

9.45 7.48

77

2 x 1-1/4 x 8 50-32-2006.30 7.13

95

2 x 1-1/4 x 8L 50-32-200L 0.55 95

2-1/2 x 1-1/2 x 5 65-40-125

2-1/2 1-1/2

3.37

14.17

4.41 5.61

1.97 3.94 2.76

8.27 6.30

0.59

0.47

0.94 1.97 1.06 0.31 10.24 1.69 0.55 1/4 3/8 1/4 3.94

75

2-1/2 x 1-1/2 x 6 65-40-160 5.20 6.40 240 190 79

2-1/2 x 1-1/2 x 8L 65-40-200L

4.15

6.30 7.19 265 212

14

99

2-1/2 x 1-1/2- x 10 65-40-2507.09 8.96 2.56 4.92 320 250

132

2-1/2 x 1-1/2 x 10L 65-40-250L 132

2-1/2 x 2 x 5 65-50-125

2-1/2 2 4.15 14.17

5.20 6.40

1.97 3.94 2.76

9.45 7.48

0.59

0.47

0.94 1.97 1.06 0.31 10.241.69

0.55 1/4 3/8 1/4 3.94

77

2-1/2 x 2 x 6 65-50-1606.30

7.1910.43 8.35

0.55

45

2-1/2 x 2 x 8L 65-50-200L 7.79 49

2-1/2 x 2 x 10L 65-50-250L 7.09 8.96 2.65 4.92 3.74 12.60 9.84 1.73 60

3 x 2-1/2 x 5 80-65-125

3 2-1/24.19

14.176.30

7.30

2.56 4.92 3.7411.02 8.35

0.59 0.55 0.94 1.97 1.06 0.31 10.241.69

0.55

1/4 3/8 1/4 3.94

86

3 x 2-1/2 x 6 80-65-160 8.09 108

3 x 2-1/2 x 8L 80-65-200L 7.09 9.08 12.60 9.84 1.73 117

3 x 2-1/2 x 10L 80-65-250L18.50

7.87 10.063.15 6.30 4.72

14.17 11.020.71 0.63 1.26 3.15 1.38 0.39 13.39 1.65 3/8 1/2 3/8 5.51

198

3 x 2-1/2 x 13L 80-65-315 5.18 8.85 11.24 15.75 12.40 253

4 x 3 x 6 100-80-160

4 3 5.24

14.177.09

9.092.56 4.92 3.74

12.60 9.840.59 0.55

0.94 1.97 1.06 0.31 10.24 1.73

0.55

1/4 3/8 1/4 3.94 128

4 x 3 x 8L 100-80-200L

18.50

10.10 13.58 11.02

1.26 3.15 1.38 0.39 13.391.65

3/8 1/2 3/8 5.51

172

4 x 3 x 10L 100-80-250L 7.87 11.283.15 6.30 4.72 15.75 12.40 0.71 0.63

214

4 x 3 x 13 100-80-315 9.87 12.66 1.69 271

5 x 4 x 8L 125-100-200L

5 4

5.28

18.50

7.8711.34

3.15 6.30 4.72

14.17 11.02

0.71 0.63 1.26 3.15 1.38 0.39 13.39

1.65

0.55

3/8

1/2

3/8

5.51 198

5 x 4 x 10L 125-100-250L

5.87

8.86

15.75 12.40 1.69

5.90 234

5 x 4 x 13 125-100-3159.84 12.72 5.51

304

5 x 4 x 13L 125-100-315L 127

5 x 4 x 16 125-100-40020.87 11.02 14.29 3.94 7.87 5.90 19.68 15.75 0.87 0.79 1.65 4.33 1.77 0.47 14.57 1.73 1/2 1/2 6.30

408

5 x 4 x 16L 125-100-400L 187

6 x 5 x 10 150-125-250L

6 5 5.95

18.50 9.8414.33

3.15 6.30 4.72 15.75 12.40 0.71 0.63 1.26 3.15 1.38 0.39 13.39 1.69

0.55

3/8

1/2

3/8 5.90 287

6 x 5 x 13L 150-125-315L20.87

11.023.94 7.87 5.90 19.68 15.75 0.87 0.79 1.65 4.33 1.77 0.47 14.57 1.65 1/2 1/2 6.30

397

6 x 5 x 6L 150-125-400L 12.40 16.10 481

8 x 6 x 13L 200-150-315L8 6 6.73 20.87

11.02 16.183.94 7.87 5.90 21.65 17.72 0.87 0.79 1.65 4.33 1.77 0.47 14.57 1.65 0.55 1/2 1/2 1/2

6.30 461

8 x 6 x 16L 200-150-400L 12.40 18.15 7.09 525


3 x 2-1/2 x 8L 80-65-250L 3" 2" 1/2 4.19 21.06 7.87 10.06 3.15 6.30 4.72 14.17 11.02 0.71 0.63 1.65 4.33 1.77 0.47 13.78 1.65 0.55 3/8 1/2 3/8 6.30 212

5 x 4 x 8L 125-100-200L 5" 4" 5.28 21.26 7.87 11.34 3.15 6.30 4.72 14.17 11.02 0.71 0.63 1.65 4.33 1.77 0.47 13.78 1.65 0.55 3/8 1/2 3/8 6.30 212







Pumps




2 x 1-1/4 x 5 50-32-125

50 32 82.5 360

112 141

50 100 70

190 140

1512

24 50 27 8 260 43 14 1/4 3/8 1/4 100

31

2 x 1-1/4 x 6 50-32-160 132 161

240 190

35

2 x 1-1/4 x 8 50-32-200160 181

43

2 x 1-1/4 x 8L 50-32-200L 14 43

2-1/2 x 1-1/2 x 5 65-40-125

65 40

85.5

360

112 142.5

50 100 70

210 160

15

12

24 50 27 8 260 43 14 1/4 3/8 1/4 100

34

2-1/2 x 1-1/2 x 6 65-40-160 132 162.5 240 190 36

2-1/2 x 1-1/2 x 8L 65-40-200L

105.5

160 182.5 265 212

14

45

2-1/2 x 1-1/2- x 10 65-40-250180 227.5 65 125 95 320 250

60

2-1/2 x 1-1/2 x 10L 65-40-250L 60

2-1/2 x 2 x 5 65-50-125

65 50 105.5 360

132 162.5

50 100 70

240 190

15

12

24 50 27 8 26043

14 1/4 3/8 1/4 100

35

2-1/2 x 2 x 6 65-50-160160

182.5265 212

14

45

2-1/2 x 2 x 8L 65-50-200L 202.5 49

2-1/2 x 2 x 10L 65-50-250L 180 227.5 65 125 95 320 250 44 60

3 x 2-1/2 x 5 80-65-125

80 65106.5

360160

185.5

65 125 95280 212

15 14 24 50 27 8 26043

14

1/4 3/8 1/4 100

39

3 x 2-1/2 x 6 80-65-160 205.5 49

3 x 2-1/2 x 8L 80-65-200L 180 230.5 320 250 44 53

3 x 2-1/2 x 10L 80-65-250L470

200 255.580 160 120

360 28018 16 32 80 35 10 340 42 3/8 1/2 3/8 140

90

3 x 2-1/2 x 13L 80-65-315 131.5 225 285.5 400 315 115

4 x 3 x 6 100-80-160

100 80 133

360180

231.065 125 95

320 25015 14

24 50 27 8 260 44

14

1/4 3/8 1/4 100 58

4 x 3 x 8L 100-80-200L

470

256.5 345 280

32 80 35 10 34042

3/8 1/2 3/8 140

78

4 x 3 x 10L 100-80-250L 200 286.580 160 120 400 315 18 16

97

4 x 3 x 13 100-80-315 250 321.5 43 123

5 x 4 x 8L 125-100-200L

125 100

134

470

200288

80 160 120

360 280

18 16 32 80 35 10 340

42

14

3/8

1/2

3/8

140 90

5 x 4 x 10L 125-100-250L

149

225

400 315 43

150 106

5 x 4 x 13 125-100-315250 323 140

138

5 x 4 x 13L 125-100-315L 127

5 x 4 x 16 125-100-400530 280 363 100 200 150 500 400 22 20 42 110 45 12 370 44 1/2 1/2 160

185

5 x 4 x 16L 125-100-400L 187

6 x 5 x 10 150-125-250L

150 125 151

470 250364

80 160 120 400 315 18 16 32 80 35 10 340 43

14

3/8

1/2

3/8 150 130

6 x 5 x 13L 150-125-315L530

280100 200 150 500 400 22 20 42 110 45 12 370 42 1/2 1/2 160

180

6 x 5 x 6L 150-125-400L 315 409 218

8 x 6 x 13L 200-150-315L200 150 171 530

280 411100 200 150 550 450 22 20 42 110 45 12 370 42 14 1/2 1/2 1/2

160 209

8 x 6 x 16L 200-150-400L 315 461 180 238


3 x 2-1/2 x 10L 80-65-250L 80 65 106.5 535 200 255.5 80 160 120 360 280 18 16 42 110 45 12 350 42 14 3/8 1/2 3/8 160 96

5 x 4 x 8L 125-100-200L 125 100 134 540 200 288 80 160 120 360 280 18 16 42 110 45 12 353 42 14 3/8 1/2 3/8 160 96



Nota: k, o, r = NPT thread




Pumps


Pump Set Dimensions at 2900 rpm – MEN 50-32-125 to 65-50-160Pump set dimensions on standardized steel baseplate NF EN 23661

North American EuropeMotor Layout Connection to pipes

Depending on the motor

Tota

l Hei

ght

Tota

l Wid

th

Tota

l Len

gth

Wei

ght (

kg)

Type KW B2 B3 L1 L2 L3 S4 a G h2 HP HR HM L

2 x 1-1/4 x 5 50-32-125F80L 1.1 370 320 800 130 540 19 80 155 140 335 195 325 720 335 370 825 75

F90S 1.5 370 320 800 130 540 19 80 155 140 335 195 325 748 335 370 825 79

2 x 1-1/4 x 6 50-32-160F90L 2.2 370 320 800 130 540 19 80 155 160 375 215 345 773 375 370 825 87

F100L 3 370 320 800 130 540 19 80 155 160 375 215 375 820 375 370 825 95

2 x 1-1/4 x 8 50-32-200F112M 4 370 320 800 130 540 19 80 155 180 423 243 423 834 423 370 834 120

F132S 5.5 400 350 900 150 600 19 80 175 180 423 243 450 896 450 400 925 138

2 x 1-1/4 x 8L 50-32-200L

F132S 7.5 400 350 900 150 600 19 80 175 180 423 243 450 896 450 400 925 145

F132M 9 400 350 900 150 600 19 80 175 180 423 243 450 934 450 400 934 154

F160M 11 450 400 1000 170 660 24 80 185 180 443 263 513 1042 513 450 1042 190

P160M 11 450 400 1000 170 660 24 80 185 180 443 263 470 1019 470 450 1019 147

2-1/2 x 1-1/2 x 5 65-40-125F90L 2.2 370 320 800 130 540 19 80 155 140 335 195 325 773 335 370 825 84

F100L 3 370 320 800 130 540 19 80 155 140 335 195 355 820 355 370 825 92

2-1/2 x 1-1/2 x 6 65-40-160

F100L 3 370 320 800 130 540 19 80 155 160 375 215 375 820 375 370 825 96

F112M 4 370 320 800 130 540 19 80 155 160 375 215 395 834 395 370 834 110

F132S 5.5 400 350 900 150 600 19 80 175 160 375 215 422 896 422 400 925 127

2-1/2 x 1-1/2 x 8L 65-40-200L

F132S 7.5 400 350 900 150 600 19 100 195 180 423 243 450 916 450 400 925 147

F132M 9 400 350 900 150 600 19 100 195 180 423 243 450 954 450 400 954 156

F160M 11 450 400 1000 170 660 24 100 205 180 443 263 513 1062 513 450 1062 192

P160M 11 450 400 1000 170 660 24 100 205 180 443 263 470 1039 470 450 1039 149

2-1/2 x 1-1/2- x 10 65-40-250

F160M 11 490 440 1120 190 740 24 100 213 225 508 283 533 1062 533 490 1143 215

F160M 15 490 440 1120 190 740 24 100 213 225 508 283 533 1062 533 490 1143 224

F160L 18.5 490 440 1120 190 740 24 100 213 225 508 283 533 1106 533 490 1143 246

P160M 11 490 440 1120 190 740 24 100 213 225 508 283 490 1039 508 490 1143 172

P160M 15 490 440 1120 190 740 24 100 213 225 508 283 490 1039 508 490 1143 180

P160L 18.5 490 440 1120 190 740 24 100 213 225 508 283 501 1072 508 490 1143 195

2-1/2 x 1-1/2 x 10L 65-40-250L

F160M 15 490 440 1120 190 740 24 100 213 225 508 283 533 1062 533 490 1143 224

F160L 18.5 490 440 1120 190 740 24 100 213 225 508 283 533 1106 533 490 1143 246

F180M 22 490 440 1120 190 740 24 100 213 225 508 283 553 1128 553 490 1143 290

P160M 15 490 440 1120 190 740 24 100 213 225 508 283 490 1039 508 490 1143 180

P160L 18.5 490 440 1120 190 740 24 100 213 225 508 283 501 1072 508 490 1143 195

P160L 22 490 440 1120 190 740 24 100 213 225 508 283 501 1072 508 490 1143 200

2-1/2 x 2 x 5 65-50-125

F100L 3 370 320 800 130 540 19 100 175 160 375 215 375 840 375 370 840 95

F112M 4 370 320 800 130 540 19 100 175 160 375 215 395 854 395 370 854 109

F132S 5.5 400 350 900 150 600 19 100 195 160 375 215 422 916 422 400 945 126

2-1/2 x 2 x 6 65-50-160F132S 5.5 400 350 900 150 600 19 100 195 180 423 243 450 916 450 400 945 139

F132S 7.5 400 350 900 150 600 19 100 195 180 423 243 450 916 450 400 945 145

NOTE: Flanges: refer to bare shaft pump dimensions. Motor: F = Totally enclosed; P = Drip-proof



Pumps


Pump Set Dimensions at 2900 rpm – MEN 65-50-200L to 80-65-250LPump set dimensions on standardized steel baseplate NF EN 23661

North American

EuropeMotor Layout Connection to pipes


Tota

l Hei

ght

Tota

l Wid

th

Tota

l Len

gth

Wei

ght (

kg)


2-1/2 x 2 x 10L 65-50-200L

F160M 15 450 400 1000 170 660 24 100 205 200 463 263 513 1062 513 450 1062 202

F160L 18.5 450 400 1000 170 660 24 100 205 200 463 263 513 1106 513 450 1106 224

F180M 22 450 400 1000 170 660 24 10 205 200 483 283 553 1128 553 450 1128 270

F200L 30 540 490 1250 205 840 24 100 228 200 503 303 597 1231 597 540 1273 342

P160M 15 450 400 1000 170 660 24 100 205 200 463 263 470 1039 470 450 1039 158

P160L 18.5 450 400 1000 170 660 24 100 205 200 463 263 481 1072 481 450 1072 173

P160L 22 450 400 1000 170 660 24 100 205 200 463 263 481 1072 481 450 1072 178

P180M 30 490 440 1120 190 740 24 100 213 200 483 283 525 1072 525 490 1143 203

2-1/2 x 2 x 10L 65-50-250L

F160L 18.5 490 440 1120 190 740 24 100 213 225 508 283 533 1106 533 490 1143 246

F180M 22 490 440 1120 190 740 24 100 213 225 508 283 553 1128 553 490 1143 287

F200L 30 540 490 1250 205 840 24 100 228 225 528 303 597 1231 597 540 1273 359

F200L 37 540 490 1250 205 840 24 100 228 225 528 303 597 1231 597 540 1273 396

P160L 18.5 490 440 1120 190 740 24 100 213 225 508 283 501 1072 508 490 1143 217

P160L 22 490 440 1120 190 740 24 100 213 225 508 283 501 1072 508 490 1143 200

P180M 30 490 440 1120 190 740 24 100 213 225 508 283 525 1072 525 490 1143 212

P180L 37 490 440 1120 190 740 24 100 213 225 508 283 525 1097 525 490 1143 235

3 x 2-1/2 x 5 80-65-125F132S 5.5 400 350 900 150 600 19 100 183 180 423 243 450 916 450 400 933 131

F132S 7.5 400 350 900 150 600 19 100 183 180 423 243 450 916 450 400 933 137

3 x 2-1/2 x 6 80-65-160

F132M 9 400 350 900 150 600 19 100 183 200 443 243 450 954 450 400 954 146

F160M 11 450 400 1000 170 660 24 100 193 200 463 263 513 1062 513 450 1062 183

F160M 15 450 400 1000 170 660 24 100 193 200 463 263 513 1062 513 450 1062 192

P160M 11 450 400 1000 170 660 24 100 193 200 463 263 470 1039 470 450 1039 140

P160M 15 450 400 1000 170 660 24 100 193 200 463 263 470 1039 470 450 1039 148

3 x 2-1/2 x 8L 80-65-200L

F160L 18.5 490 440 1120 190 740 24 100 213 225 508 283 533 1106 533 490 1143 239

F180M 22 490 440 1120 190 740 24 100 213 225 508 283 553 1128 553 490 1143 280

F200L 30 540 490 1250 205 840 24 100 228 225 528 303 597 1231 597 540 1273 374

F200L 37 540 490 1250 205 840 24 100 228 225 528 303 597 1231 597 540 1273 389

P160L 18.5 490 440 1120 190 740 24 100 213 225 508 283 501 1072 508 490 1143 188

P160L 22 490 440 1120 190 740 24 100 213 225 508 283 501 1072 508 490 1143 193

P180M 30 490 440 1120 190 740 24 100 213 225 508 283 525 1072 525 490 1143 205

P180L 37 490 440 1120 190 740 24 100 213 225 508 283 525 1097 525 490 1143 228

3 x 2-1/2 x 10L 80-65-250L

F200L 30 540 490 1250 205 840 24 100 215 250 553 303 597 1341 597 540 1341 410

F200L 37 540 490 1250 205 840 24 100 215 250 553 303 597 1341 597 540 1341 425

F225M 45 540 490 1250 205 840 24 100 215 250 578 328 696 1421 696 540 1421 553

F250M 55 610 550 1400 230 940 26 100 235 250 603 353 721 1497 721 610 1497 620

P180M 30 540 490 1250 205 840 24 100 215 250 553 303 545 1182 553 540 1260 268

P180L 37 540 490 1250 205 840 24 100 215 250 553 303 545 1207 553 540 1260 291

P200M 45 540 490 1250 205 840 24 100 215 250 553 303 573 1344 573 540 1344 335

P200L 55 540 490 1250 205 840 24 100 215 250 553 303 573 1344 573 540 1344 350




Pumps


Pump Set Dimensions at 2900 rpm – MEN 100-80-160 to 125-100-250LPump set dimensions on standardized steel baseplate NF EN 23661


North American



Tota

l Hei

ght

Tota

l Wid

th

Tota

l Len

gth

Wei

ght (

kg)


4 x 3 x 6 100-80-160

F160M 15 490 440 1120 190 740 22 125 238 225 508 283 533 1087 533 490 1168 228

F160L 18.5 490 440 1120 190 740 22 125 238 225 508 283 533 1131 533 490 1168 250

P160M 15 490 440 1120 190 740 22 125 238 225 508 283 490 1064 508 490 1168 184

P160L 18.5 490 440 1120 190 740 22 125 238 225 508 283 501 1097 508 490 1168 199

4 x 3 x 8L 100-80-200L

F180M 22 490 440 1120 190 740 22 125 238 250 533 283 553 1263 553 490 1263 306

F200L 30 540 490 1250 205 840 22 125 253 250 553 303 597 1366 597 540 1366 402

F200L 37 540 490 1250 205 840 22 125 253 250 553 303 597 1366 597 540 1366 417

F225M 45 540 490 1250 205 840 22 125 253 250 578 328 696 1446 696 610 1446 545

P160L 22 490 440 1120 190 740 22 125 238 250 533 283 501 1207 533 490 1207 224

P180M 30 490 440 1120 190 740 22 125 238 250 533 283 525 1207 533 490 1207 231

P180L 37 490 440 1120 190 740 22 125 238 250 533 283 525 1232 533 490 1232 254

P200M 45 540 490 1250 205 840 22 125 253 250 553 303 573 1369 573 540 1369 327

4 x 3 x 10L 100-80-250L

F225M 45 540 490 1250 205 840 22 125 240 280 608 328 696 1446 696 490 1446 562

F250M 55 610 550 1400 230 940 26 125 260 280 633 353 721 1522 721 610 1522 645

F280S 75 730 670 1800 300 1200 26 125 345 280 683 403 866 1635 866 730 1845 938

F280M 90 730 670 1800 300 1200 26 125 345 280 683 403 866 1635 866 730 1845 988

P200M 45 540 490 1250 205 840 22 125 240 280 583 303 573 1369 583 540 1369 342

P200L 55 540 490 1250 205 840 22 125 240 280 583 303 573 1369 583 540 1369 357

P225M 75 540 490 1250 205 840 22 125 240 280 608 328 648 1447 648 540 1447 417

P250S 90 610 550 1400 230 940 26 125 260 280 633 353 746 1518 746 610 1518 520

5 x 4 x 8L 125-100-200L

F200L 37 540 490 1250 205 840 22 125 240 280 608 303 597 1366 608 540 1366 425

F225M 45 540 490 1250 205 840 22 125 240 280 608 328 696 1446 696 540 1446 555

F250M 55 610 550 1400 230 940 26 125 260 280 633 353 721 1522 721 610 1522 638

F280S 75 730 670 1800 300 1200 26 125 345 280 683 403 866 1635 866 730 1845 931

P180L 37 540 490 1250 205 840 22 125 240 280 583 303 545 1232 583 540 1285 296

P200M 45 540 490 1250 205 840 22 125 240 280 608 303 573 1369 608 540 1369 335

P200L 55 540 490 1250 205 840 22 125 240 280 608 303 573 1369 608 540 1369 350

P225M 75 540 490 1250 205 840 22 125 240 280 608 328 648 1447 648 540 1447 412

5 x 4 x 10L 125-100-250L

F250M 55 610 550 1400 230 940 26 140 275 280 633 353 721 1537 721 610 1537 652

F280S 75 730 670 1800 300 1200 26 140 345 280 683 403 866 1650 866 730 1845 945

F280M 90 730 670 1800 300 1200 26 140 345 280 683 403 866 1650 866 730 1845 995

F315S 110 730 670 1800 300 1200 26 140 345 280 718 438 930 1740 930 730 1845 1102

P200L 55 540 490 1250 205 840 22 140 255 280 608 328 598 1384 608 540 1384 374

P225M 75 540 490 1250 205 840 22 140 255 280 608 328 648 1462 648 540 1462 422

P250S 90 610 550 1400 230 940 26 140 275 280 633 353 746 1533 746 610 1533 527

P250M 110 610 550 1400 230 940 26 140 275 280 633 353 746 1533 746 610 1533 553



Pumps


Pump Set Dimensions at 1450 rpm – MEN 50-32-125 to 80-65-315Pump set dimensions on standardized steel baseplate NF EN 23661


North American EuropeMotor Layout Connection to pipes


Tota

l Hei

ght

Tota

l Wid

th

Tota

l Len

gth

Wei

ght (

kg)

Type KW B2 B3 L1 L2 L3 S4 a G h2 HP HR HM L2 x 1-1/4 x 5 50-32-125 F80L 0.55 370 320 800 130 540 22 80 155 140 335 195 307 720 335 370 825 742 x 1-1/4 x 6 50-32-160 F80L 0.55 370 320 800 130 540 22 80 155 160 375 215 327 720 375 370 825 802 x 1-1/4 x 8 50-32-200 F90S 1.1 370 320 800 130 540 22 80 155 180 423 243 373 748 423 370 825 100

2 x 1-1/4 x 8L 50-32-200LF90S 1.1 370 320 800 130 540 22 80 155 180 423 243 373 748 423 370 825 101F90L 1.5 370 320 800 130 540 22 80 155 180 423 243 373 773 423 370 825 102

2-1/2 x 1-1/2 x 5 65-40-125 F80L 055 370 320 800 130 540 22 80 155 140 335 195 307 720 335 370 825 772-1/2 x 1-1/2 x 6 65-40-160 F80L 0.75 370 320 800 130 540 22 80 155 160 375 215 327 720 375 370 825 83

2-1/2 x 1-1/2 x 8L 65-40-200LF90S 1.1 370 320 800 130 540 22 100 175 180 423 243 373 768 423 370 825 103F90L 1.5 370 320 800 130 540 22 100 175 180 423 243 373 793 423 370 825 104

2-1/2 x 1-1/2- x 10 65-40-250F90L 1.5 450 400 1000 170 660 22 100 193 225 508 283 413 793 508 450 1023 140

F100L 2.2 450 400 1000 170 660 22 100 193 225 508 283 433 840 508 450 1023 147

2-1/2 x 1-1/2 x 10L 65-40-250L

F90L 1.5 450 400 1000 170 660 22 100 193 225 508 283 413 793 508 450 1023 142F100L 2.2 450 400 1000 170 660 22 100 193 225 508 283 433 840 508 450 1023 149F100L 3 450 400 1000 170 660 22 100 193 225 508 283 433 840 508 450 1023 153

2-1/2 x 2 x 5 65-50-125 F80L 0.75 370 320 800 130 540 22 100 175 160 375 215 327 740 375 370 845 822-1/2 x 2 x 6 65-50-160 F90S 1.1 370 320 800 130 540 22 100 175 180 423 243 373 768 423 370 845 102

2-1/2 x 2 x 8L 65-50-200L

F100L 2.2 370 320 800 130 540 22 100 175 200 443 243 393 840 443 370 845 118F100L 3 370 320 800 130 540 22 100 175 200 443 243 393 840 443 370 845 120F112M 4 370 320 800 130 540 22 100 175 200 443 243 423 857 443 370 857 131

2-1/2 x 2 x 10L 65-50-250L

F100L 3 450 400 1000 170 660 22 100 193 225 508 283 433 840 508 450 1023 156F112M 4 450 400 1000 170 660 22 100 193 225 508 283 463 857 508 450 1023 167F132S 5.5 450 400 1000 170 660 22 100 193 225 508 283 490 916 508 450 1023 179

3 x 2-1/2 x 5 80-65-125F90S 1.1 400 350 900 150 600 22 100 183 180 423 243 373 768 423 400 933 102F90L 1.5 400 350 900 150 600 22 100 183 180 423 243 373 793 423 400 933 103

3 x 2-1/2 x 6 80-65-160F90L 1.5 400 350 900 150 600 22 100 183 200 443 243 373 793 443 400 933 114

F100L 2.2 400 350 900 150 600 22 100 183 200 443 243 393 840 443 400 933 120

3 x 2-1/2 x 8L 80-65-200L

F100L 3 450 400 1000 170 660 22 100 193 225 508 283 433 840 508 450 1023 149F112M 4 450 400 1000 170 660 22 100 193 225 508 283 463 857 508 450 1023 160F132S 5.5 450 400 1000 170 660 22 100 193 225 508 283 490 916 508 450 1023 172

3 x 2-1/2 x 10L 80-65-250L

F112M 4 490 440 1120 190 740 22 100 200 250 553 303 483 967 553 490 1130 208F132S 5.5 490 440 1120 190 740 22 100 200 250 553 303 510 1026 553 490 1130 220F132M 7.5 490 440 1120 190 740 22 100 200 250 553 303 510 1064 553 490 1130 228

3 x 2-1/2 x 13L 80-65-315

F132S 7.5 540 490 1250 205 840 22 125 240 280 608 328 535 1089 608 540 1285 276F160M 11 540 490 1250 205 840 22 125 240 280 608 328 578 1197 608 540 1285 320P160M 11 540 490 1250 205 840 22 125 240 280 608 328 535 1174 608 540 1285 320



Pumps




North American



Tota

l Hei

ght

Tota

l Wid

th

Tota

l Len

gth

Wei

ght (

kg)


4 x 3 x 6 100-80-160F100L 2.2 450 400 1000 170 660 22 125 218 225 508 283 433 865 508 450 1048 148F100L 3 450 400 1000 170 660 22 125 218 225 508 283 433 865 508 450 1048 152

4 x 3 x 8L 100-80-200LF112M 4 490 440 1120 190 740 22 125 238 250 533 283 463 992 533 490 1168 194F132S 5.5 490 440 1120 190 740 22 125 238 250 533 283 490 1051 533 490 1168 206F132M 7.5 490 440 1120 190 740 22 125 238 250 533 283 490 1089 533 490 1168 214

4 x 3 x 10L 100-80-250L

F132S 5.5 540 490 1250 205 840 22 125 240 280 583 303 510 1051 583 540 1285 251F132M 7.5 540 490 1250 205 840 22 125 240 280 583 303 510 1085 583 540 1285 259F160M 11 540 490 1250 205 840 22 125 240 280 583 303 553 1197 583 540 1285 302P160M 11 540 490 1250 205 840 22 125 240 280 583 303 510 1174 583 540 1285 253

4 x 3 x 13 100-80-315

F160M 11 540 490 1250 205 840 22 125 240 315 668 353 603 1197 668 540 1285 339F160L 15 540 490 1250 205 840 22 125 240 315 668 353 603 1241 668 540 1285 350P160M 11 540 490 1250 205 840 22 125 240 315 668 353 560 1174 668 540 1285 290P160L 15 540 490 1250 205 840 22 125 240 315 668 353 571 1207 668 540 1285 309

5 x 4 x 8L 125-100-200L

F132S 5.5 490 440 1120 190 740 22 125 225 280 583 303 510 1051 583 490 1155 223F132M 7.5 490 440 1120 190 740 22 125 225 280 583 303 510 1089 583 490 1155 231F160M 11 490 440 1120 190 740 22 125 225 280 583 303 553 1197 583 540 1285 295P160M 11 490 440 1120 190 740 22 125 225 280 583 303 510 1174 583 540 1285 246

5 x 4 x 10L 125-100-250L

F132M 7.5 540 490 1250 205 840 22 140 255 280 608 328 535 1104 608 540 1300 275F160M 11 540 490 1250 205 840 22 140 255 280 608 328 578 1212 608 540 1300 320F160L 15 540 490 1250 205 840 22 140 255 280 608 328 578 1212 608 540 1300 331P160M 11 540 490 1250 205 840 22 140 255 280 608 328 535 1189 608 540 1300 271P160L 15 540 490 1250 205 840 22 140 255 280 608 328 546 1222 608 540 1300 290

5 x 4 x 13 125-100-315

F160L 15 540 490 1250 205 840 22 140 255 315 668 353 603 1256 668 540 1300 365F180M 18.5 540 490 1250 205 840 22 140 255 315 668 353 623 1278 668 540 1300 409F180L 22 540 490 1250 205 840 22 140 255 315 668 353 623 1316 668 540 1316 425P160L 15 540 490 1250 205 840 22 140 255 315 668 353 571 1222 668 540 1300 324P160L 18.5 540 490 1250 205 840 22 140 255 315 668 353 571 1222 668 540 1300 332P180M 22 540 490 1250 205 840 22 140 255 315 668 353 595 1222 668 540 1300 338

5 x 4 x 13L 125-100-315L

F180M 18.5 540 490 1250 205 840 22 140 255 315 668 353 623 1278 668 540 1300 396F180L 22 540 490 1250 205 840 22 140 255 315 668 353 623 1316 668 540 1316 416F200L 30 540 490 1250 205 840 22 140 255 315 668 353 647 1381 668 540 1381 463P160L 18.5 540 490 1250 205 840 22 140 255 315 668 353 571 1222 668 540 1300 323P180M 22 540 490 1250 205 840 22 140 255 315 668 353 595 1222 668 540 1300 329P180L 30 540 490 1250 205 840 22 140 255 315 668 353 595 1247 668 540 1300 359



Pumps




North American



Tota

l Hei

ght

Tota

l Wid

th

Tota

l Len

gth

Wei

ght (

kg)


5 x 4 x 16 125-100-400

F180M 18.5 660 600 1600 270 1060 26 140 300 355 758 403 673 1338 758 660 1630 528F180L 22 660 600 1600 270 1060 26 140 300 355 758 403 673 1376 758 660 1630 548F200L 30 660 600 1600 270 1060 26 140 300 355 758 403 697 1441 758 660 1630 593F225S 37 660 600 1600 270 1060 26 140 300 355 758 403 771 1491 771 660 1630 680P160L 18.5 660 600 1600 270 1060 26 140 300 355 758 403 621 1282 758 660 1630 455P180M 22 660 600 1600 270 1060 26 140 300 355 758 403 645 1282 758 660 1630 461P180L 30 660 600 1600 270 1060 26 140 300 355 758 403 645 1307 758 660 1630 491P200M 37 660 600 1600 270 1060 26 140 300 355 758 403 673 1444 758 660 1630 518

5 x 4 x 16L 125-100-400L

F180L 22 660 600 1600 270 1060 26 140 300 355 758 403 673 1376 758 660 1630 553F200L 30 660 600 1600 270 1060 26 140 300 355 758 403 697 1441 758 660 1630 598F225S 37 660 600 1600 270 1060 26 140 300 355 758 403 771 1491 771 660 1630 685F225M 45 660 600 1600 270 1060 26 140 300 355 758 403 771 1521 771 660 1630 735P180M 22 660 600 1600 270 1060 26 140 300 355 758 403 645 1282 758 660 1630 466P180L 30 660 600 1600 270 1060 26 140 300 355 758 403 645 1307 758 660 1630 496P200M 37 660 600 1600 270 1060 26 140 300 355 758 403 673 1444 758 660 1630 523P200L 45 660 600 1600 270 1060 26 140 300 355 758 403 673 1444 758 660 1630 548

6 x 5 x 10 150-125-250L

F160L 15 540 490 1250 205 840 22 140 255 355 708 353 603 1256 708 540 1300 358F180M 18.5 540 490 1250 205 840 22 140 255 355 708 353 623 1278 708 540 1300 398F180L 22 540 490 1250 205 840 22 140 255 355 708 353 623 1316 708 540 1316 418P160L 15 540 490 1250 205 840 22 140 255 355 708 353 571 1222 708 540 1300 317P160L 18.5 540 490 1250 205 840 22 140 255 355 708 353 571 1222 708 540 1300 325P180M 22 540 490 1250 205 840 22 140 255 355 708 353 595 1222 708 540 1300 331

6 x 5 x 13L 150-125-315L

F200L 30 660 600 1600 270 1060 26 140 300 355 758 403 697 1441 758 660 1630 591F225S 37 660 600 1600 270 1060 26 140 300 355 758 403 771 1491 771 660 1630 678F225M 45 660 600 1600 270 1060 26 140 300 355 758 403 771 1521 771 660 1630 728P180L 30 660 600 1600 270 1060 26 140 300 355 758 403 645 1307 758 660 1630 489P200M 37 660 600 1600 270 1060 26 140 300 355 758 403 673 1444 758 660 1630 516P200L 45 660 600 1600 270 1060 26 140 300 355 758 403 673 1444 758 660 1630 541

6 x 5 x 6L 150-125-400L

F225M 45 660 600 1600 270 1060 26 140 300 400 838 438 806 1521 838 660 1630 784F250M 55 660 600 1600 270 1060 26 140 300 400 838 438 806 1597 838 660 1630 856F280S 75 730 670 1800 300 1200 26 140 330 400 838 438 901 1710 901 730 1830 1105F280M 90 730 670 1800 300 1200 26 140 330 400 838 438 901 1710 901 730 1830 1215P200L 45 660 600 1600 270 1060 26 140 300 400 838 438 708 1444 838 660 1630 601P225M 55 660 600 1600 270 1060 26 140 300 400 838 438 758 1522 838 660 1630 644P250S 75 660 600 1600 270 1060 26 140 300 400 838 438 831 1593 838 660 1630 731P250M 90 660 600 1600 270 1060 26 140 300 400 838 438 831 1593 838 660 1630 756



Pumps


Pump Set Dimensions at 1450 rpm – MEN 200-150-315L to 200-150-400LPump set dimensions on standardized steel baseplate NF EN 23661


North American



Tota

l Hei

ght

Tota

l Wid

th

Tota

l Len

gth

Wei

ght (

kg)


8 x 6 x 13L 200-150-315L

F225S 37 730 670 1800 300 1200 26 160 350 400 803 403 771 1511 803 730 1850 741F225M 45 730 670 1800 300 1200 26 160 350 400 803 403 771 1541 803 730 1850 791F250M 55 730 670 1800 300 1200 26 160 350 400 803 403 771 1617 803 730 1850 863F280S 75 730 670 1800 300 1200 26 160 350 400 803 403 866 1730 866 730 1850 1080P200M 37 730 670 1800 300 1200 26 160 350 400 803 403 673 1464 803 730 1850 578P200L 45 730 670 1800 300 1200 26 160 350 400 803 403 673 1464 803 730 1850 603P225M 55 730 670 1800 300 1200 26 160 350 400 803 403 723 1542 803 730 1850 651P250S 75 730 670 1800 300 1200 26 160 350 400 803 403 796 1613 803 730 1850 738

8 x 6 x 16L 200-150-400L

F250M 55 730 670 1800 300 1200 26 160 350 450 888 438 806 1617 888 730 1850 912F280S 75 730 670 1800 300 1200 26 160 350 450 888 438 901 1730 901 730 1850 1129F280M 90 730 670 1800 300 1200 26 160 350 450 888 438 901 1730 901 730 1850 1239F315S 110 730 670 1800 300 1200 26 160 350 450 888 438 930 1820 930 730 1850 1244F315M 132 730 670 1800 300 1200 26 160 350 450 888 438 930 1850 930 730 1850 1424P225M 55 730 670 1800 300 1200 26 160 350 450 888 438 758 1542 888 730 1850 700P250S 75 730 670 1800 300 1200 26 160 350 450 888 438 831 1613 888 730 1850 787P250M 90 730 670 1800 300 1200 26 160 350 450 888 438 831 1613 888 730 1850 812P280S 110 730 670 1800 300 1200 26 160 350 450 888 438 854 1707 888 730 1850 904P280M 132 730 670 1800 300 1200 26 160 350 450 888 438 854 1707 888 730 1850 959



Pumps


North America – MEN Process Pump – 125# Flange

Frame Size

Pump Size Inlet x Outlet - Max. Imp Dia

Suction Discharge Pump Wt. lbs (kg) A B C D E F G K L M N P

U

North American Europe Shaft Ø Keyway

24

2 x 1-1/4 x 5 50-32-125

2.0 1.25

68 (31)

17.3 (440) 3.25 (80)

5.39 (137) 4.41 (112) 5.51 (140)

2.75 (70) 11.61 (295)

7.48 (190)

4.33 (110) 6.30 (160) 0.55 (14)

0.59 (15) 0.94 (24) 0.31 x 0.16 (8 x 4)

2 x 1-1/4 x 6 50-32-160 77 (35) 6.18 (157) 5.20 (132)

7.48 (190) 9.45 (240)2 x 1-1/4 x 8 50-32-200 95 (43)6.98 (177)

6.30 (160)2 x 1-1/4 x 8L 50-32-200L 95 (43)

2-1/2 x 1-1/2 x 5 65-40-125

2.5 1.5

75 (34) 5.47 (139) 6.30 (160) 8.27 (210)

2-1/2 x 1-1/2 x 6 65-40-160 79 (36) 6.26 (159) 5.20 (132) 7.48 (190) 9.45 (240)

2-1/2 x 1-1/2 x 8L 65-40-200L 99 (45)

18.1 (460) 3.94 (100)

7.05 (179) 6.30 (160) 8.35 (212) 10.43 (265)

2-1/2 x 1-1/2- x 10 65-40-250 132 (60)8.82 (224) 7.09 (180) 9.84 (250) 3.74 (95) 12.11 (308) 12.60 (320)

2-1/2 x 1-1/2 x 10L 65-40-250L 132 (60)

2-1/2 x 2 x 5 65-50-125

2.5 2.0

77 (35) 6.22 (158) 5.20 (132) 7.48 (190)

2.75 (70) 11.61 (295)

9.45 (240)

2-1/2 x 2 x 6 65-50-160 99 (45) 7.01 (178)6.30 (160) 8.35 (212) 10.43 (265)

2-1/2 x 2 x 8L 65-50-200L 108 (49) 7.90 (200)

2-1/2 x 2 x 10L 65-50-250L 132 (60) 8.78 (223) 7.09 (180) 9.84 (250)

3.74 (95) w12.11 (308)

12.60 (320)

3 x 2-1/2 x 5 80-65-125

3.0 2.5

86 (39) 7.33 (186)6.30 (160) 8.35 (212) 11.02 (280)

3 x 2-1/2 x 6 80-65-160 108 (49) 7.92 (201)

3 x 2-1/2 x 8L 80-65-200L 117 (53) 8.90 (226)7.09 (180) 9.84 (250) 12.60 (320)

4 x 3 x 6 100-80-160 4.0 3.0 128 (58) 19.1 (485) 4.92 (125) 8.93 (227) 4.92 (125) 12.70 (323)

32

3 x 2-1/2 x 10L 80-65-250L3.0 2.5

198 (90) 22.4 (570) 3.94 (100) 9.88 (250) 7.87 (200) 11.02 (280)4.72 (120) 15.75 (400)

14.17 (360)

0.71 (18) 1.26 (32) 0.39 x 0.20 (10 x 5)

3 x 2-1/2 x 13L 80-65-315L 235 (115)

23.4 (595) 4.92 (125)

11.06 (281) 8.86 (225) 12.40 (315) 15.75 (400)

4 x 3 x 8L 100-80-200L4.0 3.0

172 (78) 9.88 (250) 7.09 (180) 11.02 (280) 4.92 (125) 15.85 (403) 13.58 (345)

4 x 3 x 10L 100-80-250L 214 (97) 11.06 (281) 7.87 (200)12.40 (315)

4.72 (120)

15.75 (400)

15.75 (400)4 x 3 x 13 100-80-315L

5.0 4.0

271 (123) 12.44 (316) 9.84 (250)

5 x 4 x 8L 125-100-200L 198 (90)11.14 (283)

7.87 (200) 11.02 (280) 14.17 (360)

5 x 4 x 10L 125-100-250L 234 (106)

24.0 (610) 5.51 (140)

8.86 (225)

12.40 (315) 15.75 (400)5 x 4 x 13 125-100-315 304 (138)12.52 (318) 9.84 (250)

5 x 4 x 13L 125-100-315L 280 (127)

42

3 x 2-1/2 x 10L 80-65-250L 3.0 2.5 218 (99) 24.9 (632) 3.94 (100) 9.88 (250) 7.87 (200)11.02 (280)

16.17 (410)14.17 (360) 0.71 (18)

1.65 (42) 0.47 x 0.24 (12 x 6)

5 x 4 x 16L 125-100-200L

5.0 4.0

253 (115) 26.2 (655)

4.92 (125)

11.14 (283) 8.86 (225) 13.90 (353)

5 x 4 x 16 125-100-400 408 (185)36.4 (925)

14.09 (358)

7.09 (180)15.75 (400) 5.91 (150) 17.52 (445) 19.69 (500)

0.87 (22)

5 x 4 x 16L 125-100-400L 412 (187) 7.87 (200)

6 x 5 x 10 150-125-250L

6.0 5.0

287 (130 24.0 (610) 9.84 (250) 12.40 (315) 4.72 (120) 15.75 (400) 15.75 (400)

6 x 5 x 13L 150-125-315L 397 (180)36.4 (925)

7.87 (200) 19.69 (500)

5.91 (150) 17.52 (445)

19.69 (500)6 x 5 x 6L 150-125-400L 481 (218)

5.51 (140)

15.87 (403) 8.86 (225) 15.75 (400)

8 x 6 x 13L 200-150-315L8.0 6.0

461 (209)27.2 (690)

15.95 (405)9.84 (250) 17.72 (450) 21.65 (550)

8 x 6 x 16L 200-150-400L 525 (238) 17.91 (455)

1. Dimensions in parentheses () are in millimeters.

Bare Pump Dimensions



Pumps


North America – MEN Process Pump – 24 Frame 125# – Type A Base Mount

Base Max. Motor Frame HA HB HE HF HG HHØ Weight

lbs (kg)

139 184T 15 (381) 39 (991) 4.5 (114) 36.50 (927) 3.75 (95)

0.75 (19)

111 (50)

148 256T 18 (457) 48 (1219) 6 (152) 45.5 (1156) 4.13 (105) 163 (74)

153 326T 21 (533) 53 (1346) 7.5 (191) 50.50 (1283) 4.75 (121) 212 (96)

1. Dimensions in parentheses () are in millimeters.2. Installation dimensions are ±0.13" (3) unless otherwise noted.

Pump Dimensions

Baseplate and Mounting Dimensions

Pump Size Inlet x Outlet - Max. Imp Dia

wt A B C D E F G K L M NU


2 x 1-1/4 x 5 50-32-125 68 (31) 17.3 (440)

3.25 (80)

5.39 (137)

4.41 (112)

9.92 (252)

5.51 (140)

2.75 (70)

11.61 (295)

4.33 (110) .59 (15) .55 (14) .94 (24) .31 X .16

(8 X 4)

2 x 1-1/4 x 6 50-32-160 77 (35) 17.3 (440)

3.25 (80)

6.18 (157)

5.20 9132)

11.50 (292)

7.48 (190)

2.75 (70)

11.61 (295)

2 x 1-1/4 x 8 50-32-200 95 (43) 17.3 (440)

3.25 (80)

6.98 (177)

6.30 (180)

13.39 (340)

7.48 (190)

2.75 (70)

11.61 (295)

2 x 1-1/4 x 8L 50-32-200L 95 (43) 17.3 (440)

3.25 (80)

6.98 (177)

6.30 (180)

13.39 (340)

7.48 (190)

2.75 (70)

11.61 (295)

2-1/2 x 1-1/2 x 5 65-40-125 75 (34) 17.3 (440)

3.25 (80)

5.47 (138)

6.30 (180)

9.92 (252)

6.30 (160)

2.75 (70)

11.61 (295)

2-1/2 x 1-1/2 x 6 65-40-160 79 (36) 17.3 (440)

3.25 (80)

6.26 (159)

5.20 (132)

11.50 (292)

7.48 (190)

2.75 (70)

11.61 (295)

2-1/2 x 1-1/2 x 8L 65-40-200L 99 (45) 18.1 (460)

3.94 (100)

7.05 (179)

6.30 (180)

13.39 (340)

8.35 (212)

2.75 (70)

11.61 (295)

2-1/2 x 1-1/2- x 10 65-40-250 132 (60) 18.1 (460)

3.94 (100)

8.82 (224)

7.09 (180)

15.94 (405)

9.84 (250)

3.74 (95)

12.11 (308)

2-1/2 x 1-1/2 x 10L 65-40-250L 132 (60) 18.1 (460)

3.94 (100)

8.82 (224)

7.09 (180)

15.94 (405)

9.84 (250)

3.74 (95)

12.11 (308)

2-1/2 x 2 x 5 65-50-125 77 (35) 18.1 (460)

3.94 (100)

6.22 (158)

5.20 9132)

11.50 (292)

7.48 (190)

2.75 (70)

11.61 (295)

2-1/2 x 2 x 6 65-50-160 99 (45) 18.1 (460)

3.94 (100)

7.01 (178)

6.30 (180)

13.39 (340)

8.35 (212)

2.75 (70)

11.61 (295)

2-1/2 x 2 x 8L 65-50-200L 108 (49) 18.1 (460)

3.94 (100)

7.90 (201)

6.30 (180)

14.17 (360)

8.35 (212)

2.75 (70)

11.61 (295)

2-1/2 x 2 x 10L 65-50-250L 132 (60) 18.1 (460)

3.94 (100)

8.78 (223)

7.09 (180)

15.94 (405)

9.84 (250)

3.74 (95)

12.11 (308)

3 x 2-1/2 x 5 80-65-125 86 (39) 18.1 (460)

3.94 (100)

7.33 (186)

6.30 (180)

13.39 (340)

8.35 (212)

3.74 (95)

12.11 (308)

3 x 2-1/2 x 6 80-65-160 108 (49) 18.1 (460)

3.94 (100)

7.92 (201)

6.30 (180)

14.17 (360)

8.35 (212)

3.74 (95)

12.11 (308)

3 x 2-1/2 x 8L 80-65-200L 117 (53) 18.1 (460)

3.94 (100)

8.90 (226)

7.09 (180)

15.94 (405)

9.84 (250)

3.74 (95)

12.11 (308)

4 x 3 x 6 100-80-160 128 (58) 19.4 (493)

5.04 (128)

8.93 (227)

7.09 (180)

16.02 (407)

9.84 (250)

3.74 (95)

12.70 (323)



Pumps



Pump Dimensions


Pump Size Inlet x Outlet - Max. Imp Dia Pump Wt.

lbs (kg) A B C D E F G K L M NU


3 x 2-1/2 x 10L 80-65-250L 198 (90) 22.4 (570) 3.94 (100) 9.88 (250) 7.87 (200) 17.72 (450) 11.02 (280)4.72 (120) 15.75 (400)

4.33 (110) 0.71 (18) 0.55 (14) 1.26 (32) 0.39 x 0.20 (10 x 5)

3 x 2-1/2 x 13L 80-65-315 253 (115)

23.4 (595) 4.92 (125)

11.06 (281) 8.86 (225) 19.88 (505) 12.40 (315)

4 x 3 x 8L 100-80-200L 172 (78) 9.88 (250) 7.09 (180) 16.93 (430) 11.02 (280) 3.74 (95) 15.85 (403)

4 x 3 x 10L 100-80-250L 214 (97) 11.06 (281) 7.87 (200) 18.90 (480)12.40 (315)

4.72 (120) 15.75 (400)

4 x 3 x 13 100-80-315 271(123) 12.44 (316) 9.84 (250) 22.24 (565)

5 x 4 x 8L 125-100-200L 198 (90)11.14 (283)

7.87 (200) 18.90 (480) 11.02 (280)

5 x 4 x 10L 125-100-250L 234 (106)

24.0 (610) 5.51 (140)

8.86 (225) 19.88 (505)

12.40 (315)5 x 4 x 13 125-100-315 304 (138)12.52 (318) 9.84 (250) 22.24 (565)

5 x 4 x 13L 125-100-315L 280 (127)

Base Max. Motor Frame HA HB HE HF HG HHØ Weight

lbs (kg)

258 286T 21 (533) 58 (1473)7.5 (191)

55.50 (1410)

4.75 (121) 1.00 (25)

2.34 (106)

264 365T 22 (558) 64 (1626) 61.50 (1562) 328 (149)

268 405T26 (660)

68 (1727)9.5 (241)

65.50 (1664) 409 (186)

280 449TS 80 (2032) 77.50 (1968) 481 (218)

1. Dimensions in parentheses () are in millimeters.2. Installation dimensions are ±0.13" (3) unless otherwise noted.



Pumps



Pump Dimensions


Bare Pump Mounting

Dimensions

Pump Size Inlet x Outlet - Max. Imp Dia Pump Wt.

lbs (kg) A B C D E F G K L M NU


3 x 2-1/2 x 10L 80-65-250L 218 (99) 24.9 (633) 3.94 (100) 9.88 (250)7.87 (200)

17.72 (450)11.02 (280) 4.72 (120)

16.17 (410)

4.33 (110)

0.71 (18)

0.55 (14) 1.65 (42) 0.47 x 0.24 (12 x 6)

5 x 4 x 8L 125-100-200L 253 (115) 26.2 (655) 4.92 (125) 11.14 (283) 18.90 (480) 13.90 (353)

5 x 4 x 16 125-100-400 408 (185)36.4 (925)

5.51 (140)14.09 (358)

11.02 (280) 25.00 (635) 15.75 (400) 5.91 (150) 17.52 (445)

0.87 (22)

5 x 4 x 16L 125-100-400L 412 (187)

6 x 5 x 10 150-125-250L 287 (130) 24.0 (610) 9.84 (250) 23.82 (605) 12.40 (315) 4.72 (120) 15.75 (400)

6 x 5 x 13L 150-125-315L 397 (180)36.4 (925)

11.02 (280) 25.00 (635) 19.69 (500)

5.91 (150) 17.52 (445)6 x 5 x 6L 150-125-400L 481 (218) 15.87 (403) 12.40 (315) 28.15 (715) 15.75 (400)

8 x 6 x 13L 200-150-315L 461 (209)27.2 (690) 6.30 (160)

15.95 (405) 11.02 (280) 26.77 (680)17.72 (450)

8 x 6 x 16L 200-150-400L 525 (238) 17.91 (455) 12.40 (315) 28.15 (715)

Base Max. Motor Frame HA HB HD HE HF HG HHØ Weight

lbs (kg)

258 286T 21 (533) 58 (1473)

5.49 (139)7.5 (191)

9.5 (241)

55.50 (1410)

4.75 (121) 1.00 (25)

234 (106)

264

268

365T

405T 22 (558)

26 (660)

64 (1626) 61.50 (1562) 328 (149)

68 (1727) 65.50 (1664) 409 (186)268 405T

6.08 (154)280 449TS 80 (2032)

77.50 (1968) 481 (218)2804 445TS 80 (2032) 6.83 (173)

3984 449TS 98 (2489) 9.45 (24.0) 95.50 (2426) 683 (310)

1. Dimensions in parentheses () are in millimeters.

2. Installation dimensions are ±0.13" (3) unless otherwise noted.

3. Special for 125-100-400L pump.

4. Special for 250-150-400L pump.

See Note 3

See Note 4

See Note 4



Pumps





Pumps

MEN Engineering Data

General Engineering DataHydraulic performance HI versus ISO a. Information not provided

Temperature and pressure limits b. See page 8-2

Noise levels c. See page 8-3

Nozzle loads F/M d. See pages 8-4 and 8-5

Cooling requirements for pumps e. Information not provided

Lubrication oil flow and pressure f. Information not provided

Pump data sheet forms g. Information not provided

Minimum/maximum rotating speeds h. See page 8-6

Seal piping plans i. Information not provided

External pump connections/locations schematic j. Information not provided

Seal housing dimensions and pressures k. See pages 8-7 and 8-8

Weights (pumps and baseplates) l. See page 8-9

Critical speeds and suction specific speeds (NSS) m. Information not provided

Shaft diameters at seal, bearings, couplings, impeller n. See page 8-10

Lo. 3/D4 Information not provided

WR2 and generic % speed torque curve p. See page 8-11

Bearing span q. See page 8-12

Shaft sag r. Information not provided

Impeller type, solids max, settings, thrust factors, s. balancing, inducers options See pages 8-13 to 8-15

Minimum flows t. See page 8-16

Running clearances (rings, bearings) u. Information not provided

Product line engineering calculations and v. performance correction factors See page 8-17

Pump rotation options w. Information not provided

Rotor balancing x. Information not provided

Axial thrust balancing options y. Information not provided

Casing style and flange options z. See pages 8-18 to 8-22



Pumps


b. Temperature and Pressure Limits

Maximum working pressure

discharge 16 bar (232 psi)

suction 10 bar (145 psi)

Test pressure 21 bar (304 psi)

Maximum liquid temperature

gland packing 105°C (221°F)

mechanical seal 120°C (248°F)

Working and Testing Pressures

North American

EuropeSuction

DNDischarge

DNWorkingpressure

Testing pressure

CasingThickness

mm in. mm in. bar psi bar psi mm in.

2 x 1-1/4 x 5 50-32-125 50 2 32 1-1/4 16 232 21 305 8 0.3

2 x 1-1/4 x 6 50-32-160 50 2 32 1-1/4 16 232 21 305 10 0.4

2 x 1-1/4 x 8 50-32-200 50 2 32 1-1/4 16 232 21 305 11 0.4

2 x 1-1/4 x 8L 50-32-200L 50 2 32 1-1/4 16 232 21 305 10 0.4

2-1/2 x 1-1/2 x 5 65-40-125 65 2-1/2 40 1-1/2 16 232 21 305 10 0.4

2-1/2 x 1-1/2 x 6 65-40-160 65 2-1/2 40 1-1/2 16 232 21 305 10 0.4

2-1/2 x 1-1/2 x 8L 65-40-200L 65 2-1/2 40 1-1/2 16 232 21 305 10 0.4

2-1/2 x 1-1/2- x 10 65-40-250 65 2-1/2 40 1-1/2 16 232 21 305 13 0.5

2-1/2 x 1-1/2 x 10L 65-40-250L 65 2-1/2 40 1-1/2 16 232 21 305 13 0.5

2-1/2 x 2 x 5 65-50-125 65 2-1/2 50 2 16 232 21 305 11 0.4

2-1/2 x 2 x 6 65-50-160 65 2-1/2 50 2 16 232 21 305 12 0.5

2-1/2 x 2 x 8L 65-50-200L 65 2-1/2 50 2 16 232 21 305 11 0.4

2-1/2 x 2 x 10L 65-50-250L 65 2-1/2 50 2 16 232 21 305 12 0.5

3 x 2-1/2 x 5 80-65-125 80 3 65 2-1/2 16 232 21 305 13 0.5

3 x 2-1/2 x 6 80-65-160 80 3 65 2-1/2 16 232 21 305 13 0.5

3 x 2-1/2 x 8L 80-65-200L 80 3 65 2-1/2 16 232 21 305 12 0.5

3 x 2-1/2 x 10L 80-65-250L 80 3 65 2-1/2 16 232 21 305 13 0.5

3 x 2-1/2 x 13L 80-65-315 80 3 65 2-1/2 16 232 21 305 17 0.7

4 x 3 x 6 100-80-160 100 4 80 3 16 232 21 305 14 0.6

4 x 3 x 8L 100-80-200L 100 4 80 3 16 232 21 305 13 0.5

4 x 3 x 10L 100-80-250L 100 4 80 3 16 232 21 305 14 0.6

4 x 3 x 13 100-80-315 100 4 80 3 16 232 21 305 18 0.7

5 x 4 x 8L 125-100-200L 125 5 100 4 16 232 21 305 15 0.6

5 x 4 x 10L 125-100-250L 125 5 100 4 16 232 21 305 15 0.6

5 x 4 x 13 125-100-315 125 5 100 4 16 232 21 305 19 0.7

5 x 4 x 13L 125-100-315L 125 5 100 4 16 232 21 305 18 0.7

5 x 4 x 16 125-100-400 125 5 100 4 16 232 21 305 21 0.8

5 x 4 x 16L 125-100-400L 125 5 100 4 16 232 21 305 20 0.8

6 x 5 x 10 150-125-250L 150 6 125 5 16 232 21 305 18 0.7

6 x 5 x 13L 150-125-315L 150 6 125 5 16 232 21 305 19 0.7

6 x 5 x 6L 150-125-400L 150 6 125 5 16 232 21 305 21 0.8

8 x 6 x 13L 200-150-315L 200 8 150 6 16 232 21 305 20.5 0.8

8 x 6 x 16L 200-150-400L 200 8 150 6 16 232 21 305 22 0.9

Minimum and Maximum Pressures and Temperatures

(*) With flanges ANSI 125: 13.8 bar (200 psi) max. up to 65°C (149°F)




Pumps


Motor Size and Speed

kW (hp)

Typical sound pressure level LpA at 1 m reference 20 μPa, dBA

3550 r/min 2900 r/min 1750 r/min 1450 r/min

Pump only

Pump and motor

Pump only

Pump and motor

Pump only

Pump and motor

Pump only

Pump and motor

< 0.55 (< 0.75) 72 72 64 65 62 64 62 64

0.75 (1) 72 72 64 66 62 64 62 64

1.1 (1.5) 74 74 66 67 64 64 62 63

1.5 (2) 74 74 66 71 64 64 62 63

2.2 (3) 75 76 68 72 65 66 63 64

3 (4) 75 76 70 73 65 66 63 64

4 (5) 75 76 71 73 65 66 63 64

5.5 (7.5) 76 77 72 75 66 67 64 65

7.5 (10) 76 77 72 75 66 67 64 65

11 (15) 80 81 76 78 70 71 68 69

15 (20) 80 81 76 78 70 71 68 69

18.5 (25) 81 81 77 78 71 71 69 71

22 (30) 81 81 77 79 71 71 69 71

30 (40) 83 83 79 81 73 73 71 73

37 (50) 83 83 79 81 73 73 71 73

45 (60) 86 86 82 84 76 76 74 76

55 (75) 86 86 82 84 76 76 74 76

75 (100) 87 87 83 85 77 77 75 77

90 (120) 87 88 83 85 77 78 75 78

110 (150) 89 90 85 87 79 80 77 80

150 (200) 89 90 85 87 79 80 77 80

200 (270) (1) (1) (1) (1) 85 87 83 85

300 (400) 87 90 85 86

c. Noise LevelsAttention must be given to the exposure of personnel to the noise, and local legislation will define when guidance to personnel on noise limitation is required, and when noise exposure reduction is mandatory. This is typically 80 to 85 dBA.

The usual approach is to control the exposure time to the noise or to enclose the machine to reduce emitted sound. You may have already specified a limiting noise level when the equipment was ordered, however if no noise requirements were defined, then attention is drawn to the following table to give an indication of equipment noise level so that you can take the appropriate action in your plant.

Pump noise level is dependent on a number of operational factors, flow rate, pipework design and acoustic characteristics of the building, and so the values given are subject to a 3 dBA tolerance and cannot be guaranteed.

Similarly the motor noise assumed in the “pump and motor” noise is that typically expected from standard and high efficiency motors when on load directly driving the pump. Note that a motor driven by an inverter may show an increased noise at some speeds.

If a pump unit only has been purchased for fitting with your own driver then the “pump only” noise levels in the table should be combined with the level for the driver obtained from the supplier. Consult Flowserve or a noise specialist if assistance is required in combining the values. It is recommended that where exposure approaches the prescribed limit, then site noise measurements should be made.

The values are in sound pressure level LpA at 1 m (3.3 ft) from the machine, for “free field conditions over a reflecting plane”.

For estimating sound power level LWA (re 1 pW) then add 17 dBA to the sound pressure value.

(1) The noise level of machines in this range will most likely be of values which require noise exposure control, but typical values are inappropriate.Note: for 1180 and 960 r/ min reduce 1450 r/min values by 2 dBA. For 880 and 720 r/min reduce 1450 r/min values by 3 dBA.



Pumps


d. Nozzle Loads – F/M – Cast Iron PumpsForces and moments applied to the pump flanges must never exceed the values shown in the table below:

Forces and moments values are applied to the whole flanges and not flange-by-flange.


Suction DNA Discharge DNR Forces Moment

mm in mm inFv max Fh max Mt max

daN lbf daN lbf m.daN lbf.ft

2 x 1-1/4 x 5 50-32-125 50 2.0 32 1.3 125 281 95 214 20 148

2 x 1-1/4 x 6 50-32-160 50 2.0 32 1.3 125 281 95 214 17.5 129

2 x 1-1/4 x 8 50-32-200 50 2.0 32 1.3 125 281 95 214 17.5 129

2 x 1-1/4 x 8L 50-32-200L 50 2.0 32 1.3 125 281 95 214 17.5 129

2-1/2 x 1-1/2 x 5 65-40-125 65 2.6 40 1.6 135 303 100 225 22.5 166

2-1/2 x 1-1/2 x 6 65-40-160 65 2.6 40 1.6 135 303 100 225 22.5 166

2-1/2 x 1-1/2 x 8L 65-40-200L 65 2.6 40 1.6 135 303 100 225 20 148

2-1/2 x 1-1/2- x 10 65-40-250 65 2.6 40 1.6 135 303 100 225 25 184

2-1/2 x 1-1/2 x 10L 65-40-250L 65 2.6 40 1.6 135 303 100 225 25 184

2-1/2 x 2 x 5 65-50-125 65 2.6 50 2.0 135 303 100 225 22.5 166

2-1/2 x 2 x 6 65-50-160 65 2.6 50 2.0 135 303 100 225 22.5 166

2-1/2 x 2 x 8L 65-50-200L 65 2.6 50 2.0 135 303 100 225 20 148

2-1/2 x 2 x 10L 65-50-250L 65 2.6 50 2.0 135 303 100 225 25 184

3 x 2-1/2 x 5 80-65-125 80 3.1 65 2.6 145 326 105 236 27.5 203

3 x 2-1/2 x 6 80-65-160 80 3.1 65 2.6 145 326 105 236 27.5 203

3 x 2-1/2 x 8L 80-65-200L 80 3.1 65 2.6 145 326 105 236 30 221

3 x 2-1/2 x 10L 80-65-250L 80 3.1 65 2.6 145 326 105 236 32.5 240

3 x 2-1/2 x 13L 80-65-315 80 3.1 65 2.6 145 326 105 236 32.5 240

4 x 3 x 6 100-80-160 100 3.9 80 3.1 180 405 125 281 47.5 350

4 x 3 x 8L 100-80-200L 100 3.9 80 3.1 180 405 125 281 45 332

4 x 3 x 10L 100-80-250L 100 3.9 80 3.1 180 405 125 281 45 332

4 x 3 x 13 100-80-315 100 3.9 80 3.1 180 405 125 281 47.5 350

5 x 4 x 8L 125-100-200L 125 4.9 100 3.9 320 719 190 427 95 701

5 x 4 x 10L 125-100-250L 125 4.9 100 3.9 330 742 200 450 102.5 756

5 x 4 x 13 125-100-315 125 4.9 100 3.9 310 697 185 416 92.5 682

5 x 4 x 13L 125-100-315L 125 4.9 100 3.9 310 697 185 416 92.5 682

5 x 4 x 16 125-100-400 125 4.9 100 3.9 285 641 170 382 82.5 608

5 x 4 x 16L 125-100-400L 125 4.9 100 3.9 285 641 170 382 82.5 608

6 x 5 x 10 150-125-250L 150 5.9 125 4.9 450 1012 290 652 155 1143

6 x 5 x 13L 150-125-315L 150 5.9 125 4.9 415 933 260 585 140 1033

6 x 5 x 6L 150-125-400L 150 5.9 125 4.9 410 922 255 573 137.5 1014

8 x 6 x 13L 200-150-315L 200 7.9 150 5.9 500 1124 325 731 175 1291

8 x 6 x 16L 200-150-400L 200 7.9 150 5.9 500 1124 325 731 175 1291



Pumps


d. Nozzle Loads – F/M – Stainless Steel PumpsForces and moments applied to the pump flanges must never exceed the values shown in the table below:

Forces and moments values are applied to the whole flanges and not flange-by-flange.


Suction DNA Discharge DNR Forces Moment

mm in mm inFv max Fh max Mt max

daN lbf daN lbf m.daN lbf.ft

2 x 1-1/4 x 5 50-32-125 50 2.0 32 1.3 250 562 190 427 40 295

2 x 1-1/4 x 6 50-32-160 50 2.0 32 1.3 250 562 190 427 35 258

2 x 1-1/4 x 8 50-32-200 50 2.0 32 1.3 250 562 190 427 35 258

2 x 1-1/4 x 8L 50-32-200L 50 2.0 32 1.3 250 562 190 427 35 258

2-1/2 x 1-1/2 x 5 65-40-125 65 2.6 40 1.6 270 607 200 450 45 332

2-1/2 x 1-1/2 x 6 65-40-160 65 2.6 40 1.6 270 607 200 450 45 332

2-1/2 x 1-1/2 x 8L 65-40-200L 65 2.6 40 1.6 270 607 200 450 40 295

2-1/2 x 1-1/2- x 10 65-40-250 65 2.6 40 1.6 270 607 200 450 50 369

2-1/2 x 1-1/2 x 10L 65-40-250L 65 2.6 40 1.6 270 607 200 450 50 369

2-1/2 x 2 x 5 65-50-125 65 2.6 50 2.0 270 607 200 450 45 332

2-1/2 x 2 x 6 65-50-160 65 2.6 50 2.0 270 607 200 450 45 332

2-1/2 x 2 x 8L 65-50-200L 65 2.6 50 2.0 270 607 200 450 40 295

2-1/2 x 2 x 10L 65-50-250L 65 2.6 50 2.0 270 607 200 450 50 369

3 x 2-1/2 x 5 80-65-125 80 3.1 65 2.6 290 652 210 472 55 406

3 x 2-1/2 x 6 80-65-160 80 3.1 65 2.6 290 652 210 472 55 406

3 x 2-1/2 x 8L 80-65-200L 80 3.1 65 2.6 290 652 210 472 60 443

3 x 2-1/2 x 10L 80-65-250L 80 3.1 65 2.6 290 652 210 472 65 479

3 x 2-1/2 x 13L 80-65-315 80 3.1 65 2.6 290 652 210 472 65 479

4 x 3 x 6 100-80-160 100 3.9 80 3.1 360 809 250 562 95 701

4 x 3 x 8L 100-80-200L 100 3.9 80 3.1 360 809 250 562 90 664

4 x 3 x 10L 100-80-250L 100 3.9 80 3.1 360 809 250 562 90 664

4 x 3 x 13 100-80-315 100 3.9 80 3.1 360 809 250 562 95 701

5 x 4 x 8L 125-100-200L 125 4.9 100 3.9 640 1439 380 854 190 1401

5 x 4 x 10L 125-100-250L 125 4.9 100 3.9 660 1484 400 899 205 1512

5 x 4 x 13 125-100-315 125 4.9 100 3.9 620 1394 370 832 185 1364

5 x 4 x 13L 125-100-315L 125 4.9 100 3.9 620 1394 370 832 185 1364

5 x 4 x 16 125-100-400 125 4.9 100 3.9 570 1281 340 764 165 1217

5 x 4 x 16L 125-100-400L 125 4.9 100 3.9 570 1281 340 764 165 1217

6 x 5 x 10 150-125-250L 150 5.9 125 4.9 900 2023 580 1304 310 2286

6 x 5 x 13L 150-125-315L 150 5.9 125 4.9 830 1866 520 1169 280 2065

6 x 5 x 6L 150-125-400L 150 5.9 125 4.9 820 1843 510 1147 275 2028

8 x 6 x 13L 200-150-315L 200 7.9 150 5.9 1000 2248 650 1461 350 2581

8 x 6 x 16L 200-150-400L 200 7.9 150 5.9 1000 2248 650 1461 350 2581



Pumps


h. Minimum/Maximum Rotating Speeds

Pump Size 1450 min-1 2900 min-1

North American EuropeP Qmin P Qmax P Qmin P Qmax

kw kw kw kw

2 x 1-1/4 x 5 50-32-125 0.1 0.2 1 1.6

2 x 1-1/4 x 6 50-32-160 0.2 0.3 1.7 2.7

2 x 1-1/4 x 8 50-32-200 0.4 0.8 3.2 6.6

2 x 1-1/4 x 8L 50-32-200L 0.9 1.5 6.7 11.8

2-1/2 x 1-1/2 x 5 65-40-125 0.2 0.3 1.5 2.7

2-1/2 x 1-1/2 x 6 65-40-160 0.3 0.5 2.9 4.6

2-1/2 x 1-1/2 x 8L 65-40-200L 0.6 1.3 5.6 11.3

2-1/2 x 1-1/2- x 10 65-40-250 1.2 2 10.2 17.2

2-1/2 x 1-1/2 x 10L 65-40-250L 2.2 3.7 16.5 28.4

2-1/2 x 2 x 5 65-50-125 0.4 0.5 3 4.7

2-1/2 x 2 x 6 65-50-160 0.7 1 5.5 7.8

2-1/2 x 2 x 8L 65-50-200L 2.1 3.1 12.6 23.9

2-1/2 x 2 x 10L 65-50-250L 2.3 4.2 16.9 32.5

3 x 2-1/2 x 5 80-65-125 0.6 1 4.7 8

3 x 2-1/2 x 6 80-65-160 1.2 1.9 8.7 14.9

3 x 2-1/2 x 8L 80-65-200L 2 4.1 16.5 34.4

3 x 2-1/2 x 10L 80-65-250L 3.4 6 28 52

3 x 2-1/2 x 13L 80-65-315 5.1 10.7

4 x 3 x 6 100-80-160 11.9 17.7

4 x 3 x 8L 100-80-200L 3.1 5.1 24.8 42.6

4 x 3 x 10L 100-80-250L 5.8 11 37 86.9

4 x 3 x 13 100-80-315 6.7 14

5 x 4 x 8L 125-100-200L 5.4 8.2 41.4 64.3

5 x 4 x 10L 125-100-250L 10.5 14.1 61.3 109.9

5 x 4 x 13 125-100-315 9.9 22.2

5 x 4 x 13L 125-100-315L 15.4 26.3

5 x 4 x 16 125-100-400 18.2 40.4

5 x 4 x 16L 125-100-400L 21.6 40.2

6 x 5 x 10 150-125-250L 13.4 19.6

6 x 5 x 13L 150-125-315L 18.8 40.8

6 x 5 x 6L 150-125-400L 39.2 90.2

8 x 6 x 13L 200-150-315L 31.1 53.8

8 x 6 x 16L 200-150-400L 57.9 102.3



Pumps


k. Seal Housing Dimensions and Pressures With Gland Packing

Casing cover for gland packing with studs and nuts in •stainless steel to facilitate the gland settingGland packing graphite/PTFE•

North American

Europe

Casing Cover

Gasket Gland Packing

Pump Casing/Cover Casing Lg : Total Packing Length

TypeD d D3 D4 A x A

NumberLg

mm in. mm in. mm in. mm in. mm in. mm in.

2 x 1-1/4 x 5 50-32-125 2 170 6.7 150.5 5.9 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2 x 1-1/4 x 6 50-32-160 2 188 7.4 173 6.8 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2 x 1-1/4 x 8 50-32-200 1 235 9.3 220.5 8.7 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2 x 1-1/4 x 8L 50-32-200L 1 235 9.3 220.5 8.7 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 1-1/2 x 5 65-40-125 2 170 6.7 150.5 5.9 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 1-1/2 x 6 65-40-160 2 188 7.4 173 6.8 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 1-1/2 x 8L 65-40-200L 1 235 9.3 220.5 8.7 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 1-1/2- x 10 65-40-250 1 280 11.0 265.5 10.5 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 1-1/2 x 10L 65-40-250L 1 280 11.0 265.5 10.5 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 2 x 5 65-50-125 2 170 6.7 150.5 5.9 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 2 x 6 65-50-160 1 195 7.7 178 7.0 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 2 x 8L 65-50-200L 1 240 9.4 226.5 8.9 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

2-1/2 x 2 x 10L 65-50-250L 1 280 11.0 265.5 10.5 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

3 x 2-1/2 x 5 80-65-125 2 170 6.7 150.5 5.9 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

3 x 2-1/2 x 6 80-65-160 1 195 7.7 178 7.0 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

3 x 2-1/2 x 8L 80-65-200L 1 240 9.4 226.5 8.9 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

3 x 2-1/2 x 10L 80-65-250L 1 300 11.8 280.5 11.0 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

3 x 2-1/2 x 13L 80-65-315 1 355 14.0 337.5 13.3 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

4 x 3 x 6 100-80-160 1 195 7.7 178 7.0 38 1.5 58 2.3 10 x 10 0.39 x 0.39 3 + SR 138 5.4

4 x 3 x 8L 100-80-200L 2 265 10.4 245.5 9.7 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

4 x 3 x 10L 100-80-250L 1 300 11.8 280.5 11.0 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

4 x 3 x 13 100-80-315 1 355 14.0 337.5 13.3 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

5 x 4 x 8L 125-100-200L 2 265 10.4 245.5 9.7 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

5 x 4 x 10L 125-100-250L 1 315 12.4 300.5 11.8 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

5 x 4 x 13 125-100-315 1 355 14.0 337.5 13.3 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

5 x 4 x 13L 125-100-315L 1 355 14.0 337.5 13.3 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

5 x 4 x 16 125-100-400 1 445 17.5 420.5 16.6 65 2.6 97 3.8 16 x 16 0.63 x 0.63 3 223 8.8

5 x 4 x 16L 125-100-400L 1 415 16.3 395.5 15.6 65 2.6 97 3.8 16 x 16 0.63 x 0.63 3 223 8.8

6 x 5 x 10 150-125-250L 1 315 12.4 300.5 11.8 50 2.0 76 3.0 13 x 13 0.5 x 0.5 4 176 6.9

6 x 5 x 13L 150-125-315L 1 390 15.4 370.5 14.6 65 2.6 97 3.8 16 x 16 0.63 x 0.63 3 223 8.8

6 x 5 x 6L 150-125-400L 1 450 17.7 425.5 16.8 65 2.6 97 3.8 16 x 16 0.63 x 0.63 3 223 8.8

8 x 6 x 13L 200-150-315L 1 390 15.4 370.5 14.6 65 2.6 97 3.8 16 x 16 0.63 x 0.63 3 223 8.8

8 x 6 x 16L 200-150-400L 1 450 17.7 425.5 16.8 65 2.6 97 3.8 16 x 16 0.63 x 0.63 3 223 8.8



Pumps


k. Seal Housing Dimensions and Pressures With Mechanical Seal

Cover casing for standard mechanical seal in compliance •with ISO 3069 type 43 carbon/ceramic/EP

North American

Europe

Casing Cover

GasketMechanical Seal

Pump Casing/Cover Casing

TypeD d D1 D2 L

mm in. mm in. mm in. mm in. mm in.

2 x 1-1/4 x 5 50-32-125 2 170 6.69 150.5 5.92 38 1.5 56 2.20 59.8 2.35

2 x 1-1/4 x 6 50-32-160 2 188 7.4 173 6.81 38 1.5 56 2.20 59.8 2.35

2 x 1-1/4 x 8 50-32-200 1 235 9.25 220.5 8.68 38 1.5 56 2.20 59.8 2.35

2 x 1-1/4 x 8L 50-32-200L 1 235 9.25 220.5 8.68 38 1.5 56 2.20 59.8 2.35

2-1/2 x 1-1/2 x 5 65-40-125 2 170 6.69 150.5 5.92 38 1.5 56 2.20 59.8 2.35

2-1/2 x 1-1/2 x 6 65-40-160 2 188 7.4 173 6.81 38 1.5 56 2.20 59.8 2.35

2-1/2 x 1-1/2 x 8L 65-40-200L 1 235 9.25 220.5 8.68 38 1.5 56 2.20 59.8 2.35

2-1/2 x 1-1/2- x 10 65-40-250 1 280 11.02 265.5 10.45 38 1.5 56 2.20 59.8 2.35

2-1/2 x 1-1/2 x 10L 65-40-250L 1 280 11.02 265.5 10.45 38 1.5 56 2.20 59.8 2.35

2-1/2 x 2 x 5 65-50-125 2 170 6.69 150.5 5.92 38 1.5 56 2.20 59.8 2.35

2-1/2 x 2 x 6 65-50-160 1 195 7.68 178 7.01 38 1.5 56 2.20 59.8 2.35

2-1/2 x 2 x 8L 65-50-200L 1 240 9.45 226.5 8.92 38 1.5 56 2.20 59.8 2.35

2-1/2 x 2 x 10L 65-50-250L 1 280 11.02 265.5 10.45 38 1.5 56 2.20 59.8 2.35

3 x 2-1/2 x 5 80-65-125 2 170 6.69 150.5 5.92 38 1.5 56 2.20 59.8 2.35

3 x 2-1/2 x 6 80-65-160 1 195 7.68 178 7.01 38 1.5 56 2.20 59.8 2.35

3 x 2-1/2 x 8L 80-65-200L 1 240 9.45 226.5 8.92 38 1.5 56 2.20 59.8 2.35

3 x 2-1/2 x 10L 80-65-250L 1 300 11.81 280.5 11.04 50 2.0 70 2.76 63.5 2.5

3 x 2-1/2 x 13L 80-65-315 1 355 13.98 337.5 13.29 50 2.0 70 2.76 63.5 2.5

4 x 3 x 6 100-80-160 1 195 7.68 178 7.01 38 1.5 56 2.20 59.8 2.35

4 x 3 x 8L 100-80-200L 2 265 10.43 245.5 9.66 50 2.0 70 2.76 63.5 2.5

4 x 3 x 10L 100-80-250L 1 300 11.81 280.5 11.04 50 2.0 70 2.76 63.5 2.5

4 x 3 x 13 100-80-315 1 355 13.98 337.5 13.29 50 2.0 70 2.76 63.5 2.5

5 x 4 x 8L 125-100-200L 2 265 10.43 245.5 9.66 50 2.0 70 2.76 63.5 2.5

5 x 4 x 10L 125-100-250L 1 315 12.4 300.5 11.83 50 2.0 70 2.76 63.5 2.5

5 x 4 x 13 125-100-315 1 355 13.98 337.5 13.29 50 2.0 70 2.76 63.5 2.5

5 x 4 x 13L 125-100-315L 1 355 13.98 337.5 13.29 50 2.0 70 2.76 63.5 2.5

5 x 4 x 16 125-100-400 1 445 17.52 420.5 16.55 65 2.6 85.7 3.37 85.8 3.38

5 x 4 x 16L 125-100-400L 1 415 16.34 395.5 15.57 65 2.6 85.7 3.37 85.8 3.38

6 x 5 x 10 150-125-250L 1 315 12.4 300.5 11.83 50 2.0 70 2.76 63.5 2.5

6 x 5 x 13L 150-125-315L 1 390 15.35 370.5 14.59 65 2.6 85.7 3.37 85.8 3.38

6 x 5 x 6L 150-125-400L 1 450 17.72 425.5 16.75 65 2.6 85.7 3.37 85.8 3.38

8 x 6 x 13L 200-150-315L 1 390 15.35 370.5 14.59 65 2.6 85.7 3.37 85.8 3.38

8 x 6 x 16L 200-150-400L 1 450 17.72 425.5 16.75 65 2.6 85.7 3.37 85.8 3.38



Pumps


l. Weights

North American

EuropePump mass

Mass of pumpMass of casing cover

casing

kg lb kg lb kg lb

2 x 1-1/4 x 5 MEN 50-32-125 30 66

Mass < 30 kg (66 lb)


2 x 1-1/4 x 6 MEN 50-32-160 35 77

2 x 1-1/4 x 8 MEN 50-32-200 38 84

2 x 1-1/4 x 8L MEN 50-32-200L 43 95

2-1/2 x 1-1/2 x 5 MEN 65-40-125 33 73

2-1/2 x 1-1/2 x 6 MEN 65-40-160 36 79

2-1/2 x 1-1/2 x 8L MEN 65-40-200L 44 97

2-1/2 x 1-1/2- x 10 MEN 65-40-250 51 112

2-1/2 x 1-1/2 x 10L MEN 65-40-250L 58 128

2-1/2 x 2 x 5 MEN 65-50-125 35 77

2-1/2 x 2 x 6 MEN 65-50-160 44 97

2-1/2 x 2 x 8L MEN 65-50-200L 48 106

2-1/2 x 2 x 10L MEN 65-50-250L 57 126

3 x 2-1/2 x 5 MEN 80-65-125 39 86

3 x 2-1/2 x 6 MEN 80-65-160 46 101

3 x 2-1/2 x 8L MEN 80-65-200L 55 121

3 x 2-1/2 x 10L MEN 80-65-250L 85 187 32 71

3 x 2-1/2 x 13L MEN 80-65-315 105 232 43 95

4 x 3 x 6 MEN 100-80-160 49 108 31 68

4 x 3 x 8L MEN 100-80-200L 78 172 33 73

4 x 3 x 10L MEN 100-80-250L 91 201 40 88

4 x 3 x 13 MEN 100-80-315 113 249 47 104

5 x 4 x 8L MEN 125-100-200L 94 207 43 95

5 x 4 x 10L MEN 125-100-250L 100 221 50 110

5 x 4 x 13 MEN 125-100-315 123 271 52 115

5 x 4 x 13L MEN 125-100-315L 125 276 56 124

5 x 4 x 16 MEN 125-100-400 185 408 72 159 39 86.0

5 x 4 x 16L MEN 125-100-400L 189 417 75 165 40 88

6 x 5 x 10 MEN 150-125-250L 12026500

7215900


6 x 5 x 13L MEN 150-125-315L 200 441 73 161 30 66

6 x 5 x 6L MEN 150-125-400L 230 507 88 194 38 84

8 x 6 x 13L MEN 200-150-315L 203 448 103 227 30 66

8 x 6 x 16L MEN 200-150-400L 240 529 104 229 38 84



Pumps



At ImpellerShaft Diameter

Impeller Overhang

Center

With Packing Seal With Mech. Seal Under

BearingBetween Bearing

Distance of Bearings

Ø x Lgth Under Sleeve On Sleeve Under Mech.

Seal

mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in.

2 x 1-1/4 x 5 50-32-125 22 x 35 0.63 x 1.18 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2 x 1-1/4 x 6 50-32-160 22 x 35 0.63 x 1.18 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2 x 1-1/4 x 8 50-32-200 22 x 35 0.63 x 1.18 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2 x 1-1/4 x 8L 65-40-125 22 x 35 0.63 x 1.18 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 1-1/2 x 5 65-40-160 22 x 35 0.63 x 1.18 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 1-1/2 x 6 65-50-125 22 x 35 0.63 x 1.18 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 1-1/2 x 8L 65-50-160 22 x 35 0.63 x 1.18 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 1-1/2- x 10 80-65-125 22 x 35 0.63 x 1.18 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 1-1/2 x 10L 50-32-200L 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 2 x 5 65-40-200L 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 2 x 6 65-40-250 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 2 x 8L 65-40-250L 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

2-1/2 x 2 x 10L 65-50-200L 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

3 x 2-1/2 x 5 65-50-250L 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

3 x 2-1/2 x 6 80-65-160 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

3 x 2-1/2 x 8L 80-65-200L 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

3 x 2-1/2 x 10L 100-80-160 22 x 35 0.79 x 1.57 25 1.1 38 1.3 38 1.1 30 1.2 38 1.5 163 6.4 117 4.6

3 x 2-1/2 x 13L 80-65-315 32 x 57 0.94 x 2.16 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

4 x 3 x 6 100-80-315 32 x 57 0.94 x 2.16 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

4 x 3 x 8L 125-100-315 32 x 57 0.94 x 2.16 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

4 x 3 x 10L 80-65-250L 32 x 57 1.26 x 2.36 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

4 x 3 x 13 100-80-200L 32 x 57 1.26 x 2.36 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

5 x 4 x 8L 100-80-250L 32 x 57 1.26 x 2.36 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

5 x 4 x 10L 125-100-200L 32 x 57 1.26 x 2.36 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

5 x 4 x 13 125-100-250L 32 x 57 1.26 x 2.36 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

5 x 4 x 13L 125-100-315L 32 x 57 1.26 x 2.36 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

5 x 4 x 16 150-125-250L 32 x 57 1.26 x 2.36 35 1.5 50 1.7 50 1.5 45 1.8 53 2.1 200 7.9 155 6.1

5 x 4 x 16L 125-100-400 40 x 69 1.57 x 2.72 50 2.0 65 2.2 65 2.0 55 2.2 65 2.6 228 9.0 152 6.0

6 x 5 x 10 125-100-400L 40 x 69 1.57 x 2.72 50 2.0 65 2.2 65 2.0 55 2.2 65 2.6 228 9.0 152 6.0

6 x 5 x 13L 150-125-315L 40 x 69 1.57 x 2.72 50 2.0 65 2.2 65 2.0 55 2.2 65 2.6 228 9.0 152 6.0

6 x 5 x 6L 150-125-400L 40 x 69 1.57 x 2.72 50 2.0 65 2.2 65 2.0 55 2.2 65 2.6 228 9.0 152 6.0

8 x 6 x 13L 200-150-315L 40 x 69 1.57 x 2.72 50 2.0 65 2.2 65 2.0 55 2.2 65 2.6 228 9.0 152 6.0

8 x 6 x 16L 200-150-400L 40 x 69 1.57 x 2.72 50 2.0 65 2.2 65 2.0 55 2.2 65 2.6 228 9.0 152 6.0

n. Shaft Diameters



Pumps


p. Mass Moment of Inertia (WR2)

North American

Europe J

kg.m2 lbf.in2

2 x 1-1/4 x 5 50-32-125 0.002 6.834

2 x 1-1/4 x 6 50-32-160 0.005 17.085

2 x 1-1/4 x 8 50-32-200 0.011 37.587

2 x 1-1/4 x 8L 50-32-200L 0.011 37.587

2-1/2 x 1-1/2 x 5 65-40-125 0.003 10.251

2-1/2 x 1-1/2 x 6 65-40-160 0.005 17.085

2-1/2 x 1-1/2 x 8L 65-40-200L 0.012 41.004

2-1/2 x 1-1/2- x 10 65-40-250 0.023 78.591

2-1/2 x 1-1/2 x 10L 65-40-250L 0.025 85.425

2-1/2 x 2 x 5 65-50-125 0.040 136.68

2-1/2 x 2 x 6 65-50-160 0.010 34.17

2-1/2 x 2 x 8L 65-50-200L 0.016 54.672

2-1/2 x 2 x 10L 65-50-250L 0.026 88.842

3 x 2-1/2 x 5 80-65-125 0.005 17.085

3 x 2-1/2 x 6 80-65-160 0.011 37.587

3 x 2-1/2 x 8L 80-65-200L 0.018 61.506

3 x 2-1/2 x 10L 80-65-250L 0.039 133.263

3 x 2-1/2 x 13L 80-65-315 0.014 47.838

4 x 3 x 6 100-80-160 0.013 44.421

4 x 3 x 8L 100-80-200L 0.030 102.51

4 x 3 x 10L 100-80-250L 0.056 191.352

4 x 3 x 13 100-80-315 0.111 379.287

5 x 4 x 8L 125-100-200L 0.030 102.51

5 x 4 x 10L 125-100-250L 0.052 177.684

5 x 4 x 13 125-100-315 0.130 444.21

5 x 4 x 13L 125-100-315L 0.132 451.044

5 x 4 x 16 125-100-400 0.350 1195.95

5 x 4 x 16L 125-100-400L 0.353 1206.201

6 x 5 x 10 150-125-250L 0.110 375.87

6 x 5 x 13L 150-125-315L 0.160 546.72

6 x 5 x 16L 150-125-400L 0.360 1230.12

8 x 6 x 13L 200-150-315L 0.180 615.06

8 x 6 x 16L 200-150-400L 0.390 1332.63



Pumps


q. Bearing Span

24 32 42

mm in. mm in. mm in.

Shaft diameter

Under packing 38 1.5 50 2.0 65 2.6

Mechanical seal 38 1.5 50 2.0 65 2.6

Under bearings 30 1.18 45 1.77 55 2.17

Between bearings 38 1.5 53 2.09 65 2.56

A 163 6.42 200 7.87 228 8.97

B 117 4.6 155 6.1 152 5.98



Pumps


s. Impeller DataCentrifugal radial flow impeller, shrouded and keyed•

North American

Europe

Max. Eye Outlet Width No. of

Vanes

Impeller Key Engagement Impeller Hub Ring

Ø D2 Ø Doe B2 Ø d x L Ø Dj1 Ø Dj2

mm in. mm in. mm in. mm in. mm in. mm in.

2 x 1-1/4 x 5 50-32-125 127 5.0 46.5 1.8 7.5 0.3 7 22 x 35 0.63 x 1.18 56 2.2 - -

2 x 1-1/4 x 6 50-32-160 157.5 6.2 50 2.0 6 0.2 7 22 x 35 0.63 x 1.18 62 2.4 88 3.5

2 x 1-1/4 x 8 50-32-200 205.5 8.1 53 2.1 4.2 0.2 9 22 x 35 0.63 x 1.18 62 2.4 88 3.5

2 x 1-1/4 x 8L 50-32-200L 208 8.2 63 2.5 10.7 0.4 7 22 x 35 0.79 x 1.57 76 3.0 88 3.5

2-1/2 x 1-1/2 x 5 65-40-125 131 5.2 57 2.2 11 0.4 7 22 x 35 0.63 x 1.18 67 2.6 - -

2-1/2 x 1-1/2 x 6 65-40-160 161.5 6.4 64 2.5 9 0.4 7 22 x 35 0.63 x 1.18 76 3.0 88 3.5

2-1/2 x 1-1/2 x 8L 65-40-200L 195 7.7 65 2.6 11.4 0.4 7 22 x 35 0.79 x 1.57 76 3.0 88 3.5

2-1/2 x 1-1/2- x 10 65-40-250 255 10.0 65 2.6 5.3 0.2 9 22 x 35 0.79 x 1.57 76 3.0 98 3.9

2-1/2 x 1-1/2 x 10L 65-40-250L 252 9.9 78 3.1 13 0.5 7 22 x 35 0.79 x 1.57 98 3.9 98 3.9

2-1/2 x 2 x 5 65-50-125 140 5.5 68 2.7 16 0.6 7 22 x 35 0.63 x 1.18 80 3.1 - -

2-1/2 x 2 x 6 65-50-160 166.5 6.6 70 2.8 14 0.6 7 22 x 35 0.63 x 1.18 82 3.2 88 3.5

2-1/2 x 2 x 8L 65-50-200L 222 8.7 74 2.9 13 0.5 7 22 x 35 0.79 x 1.57 82 3.2 102 4.0

2-1/2 x 2 x 10L 65-50-250L 238 9.4 80 3.1 13 0.5 7 22 x 35 0.79 x 1.57 98 3.9 98 3.9

3 x 2-1/2 x 5 80-65-125 141.5 5.6 84 3.3 23 0.9 7 22 x 35 0.63 x 1.18 98 3.9 - -

3 x 2-1/2 x 6 80-65-160 175 6.9 84 3.3 20 0.8 7 22 x 35 0.79 x 1.57 98 3.9 120 4.7

3 x 2-1/2 x 8L 80-65-200L 214 8.4 90 3.5 19 0.7 7 22 x 35 0.79 x 1.57 102 4.0 102 4.0

3 x 2-1/2 x 10L 80-65-250L 256 10.1 96 3.8 19 0.7 6 32 x 57 1.26 x 2.36 120 4.7 142 5.6

3 x 2-1/2 x 13L 80-65-315 321.5 12.7 88 3.5 11 0.4 8 32 x 57 0.95 x 2.16 102 4.0 123 4.8

4 x 3 x 6 100-80-160 176.5 6.9 106 4.2 26 1.0 7 22 x 35 0.79 x 1.57 120 4.7 120 4.7

4 x 3 x 8L 100-80-200L 224 8.8 116 4.6 20.8 0.8 6 32 x 57 1.26 x 2.36 142 5.6 142 5.6

4 x 3 x 10L 100-80-250L 270 10.6 120 4.7 22 0.9 6 32 x 57 1.26 x 2.36 142 5.6 142 5.6

4 x 3 x 13 100-80-315 321.5 12.7 108 4.3 13 0.5 8 32 x 57 0.95 x 2.16 123 4.8 123 4.8

5 x 4 x 8L 125-100-200L 220 8.7 134 5.3 32 1.3 7 32 x 57 1.26 x 2.36 155 6.1 142 5.6

5 x 4 x 10L 125-100-250L 263 10.4 139 5.5 25 1.0 6 32 x 57 1.26 x 2.36 155 6.1 155 6.1

5 x 4 x 13 125-100-315 321.5 12.7 124 4.9 19 0.7 7 32 x 57 0.95 x 2.16 142 5.6 165 6.5

5 x 4 x 13L 125-100-315L 326.7 12.9 143 5.6 26.6 1.1 6 32 x 57 1.26 x 2.36 165 6.5 165 6.5

5 x 4 x 16 125-100-400 407 16.0 116 4.6 15 0.6 8 40 x 69 1.57 x 2.72 130 5.1 130 5.1

5 x 4 x 16L 125-100-400L 384 15.1 128 5.0 22.5 0.9 7 40 x 69 1.57 x 2.72 146 5.7 146 5.7

6 x 5 x 10 150-125-250L 267.5 10.5 159 6.3 38.9 1.5 7 32 x 57 1.26 x 2.36 175 6.9 155 6.1

6 x 5 x 13L 150-125-315L 340 13.4 141 5.6 29.6 1.2 7 40 x 69 1.57 x 2.72 165 6.5 205 8.1

6 x 5 x 6L 150-125-400L 420 16.5 168 6.6 26 1.0 6 40 x 69 1.57 x 2.72 190 7.5 225 8.9

8 x 6 x 13L 200-150-315L 356 14.0 185 7.3 33 1.3 6 40 x 69 1.57 x 2.72 205 8.1 205 8.1

8 x 6 x 16L 200-150-400L 418 16.5 201 7.9 34 1.3 6 40 x 69 1.57 x 2.72 225 8.9 225 8.9



Pumps


North American

Europe

Diametral Hub Ring Clearance

Ø Dj1 H9c8 Ø Dj2 H9c8

mm in. mm in.

2 x 1-1/4 x 5 50-32-125 0.14/0.26 0.0055/0.0102 - -

2 x 1-1/4 x 6 50-32-160 0.14/0.26 0.0055/0.0102 0.17/0.311 0.0067/0.0122

2 x 1-1/4 x 8 50-32-200 0.14/0.26 0.0055/0.0102 0.17/0.311 0.0067/0.0122

2 x 1-1/4 x 8L 50-32-200L 0.15/0.27 0.0059/0.0106 0.17/0.311 0.0067/0.0122

2-1/2 x 1-1/2 x 5 65-40-125 0.15/0.27 0.0059/0.0106 - -

2-1/2 x 1-1/2 x 6 65-40-160 0.15/0.27 0.0059/0.0106 0.17/0.311 0.0067/0.0122

2-1/2 x 1-1/2 x 8L 65-40-200L 0.15/0.27 0.0059/0.0106 0.17/0.311 0.0067/0.0122

2-1/2 x 1-1/2- x 10 65-40-250 0.15/0.27 0.0059/0.0106 0.17/0.311 0.0067/0.0122

2-1/2 x 1-1/2 x 10L 65-40-250L 0.17/0.311 0.0067/0.0122 0.17/0.311 0.0067/0.0122

2-1/2 x 2 x 5 65-50-125 0.15/0.27 0.0059/0.0106 - -

2-1/2 x 2 x 6 65-50-160 0.17/0.311 0.0067/0.0122 0.17/0.311 0.0067/0.0122

2-1/2 x 2 x 8L 65-50-200L 0.17/0.311 0.0067/0.0122 0.18/0.321 0.0071/0.0126

2-1/2 x 2 x 10L 65-50-250L 0.17/0.311 0.0067/0.0122 0.17/0.311 0.0067/0.0122

3 x 2-1/2 x 5 80-65-125 0.17/0.311 0.0067/0.0122 - -

3 x 2-1/2 x 6 80-65-160 0.17/0.311 0.0067/0.0122 0.18/0.321 0.0071/0.0126

3 x 2-1/2 x 8L 80-65-200L 0.18/0.311 0.0071/0.0122 0.18/0.321 0.0071/0.0126

3 x 2-1/2 x 10L 80-65-250L 0.18/0.311 0.0071/0.0122 0.21/0.373 0.0083/0.0147

3 x 2-1/2 x 13L 80-65-315 0.18/0.311 0.0071/0.0122 0.20/0.363 0.0079/0.0143

4 x 3 x 6 100-80-160 0.18/0.321 0.0071/0.0126 0.18/0.321 0.0071/0.0126

4 x 3 x 8L 100-80-200L 0.21/0.373 0.0083/0.0147 0.21/0.373 0.0083/0.0147

4 x 3 x 10L 100-80-250L 0.21/0.373 0.0083/0.0147 0.21/0.373 0.0083/0.0147

4 x 3 x 13 100-80-315 0.20/0.363 0.0079/0.0143 0.20/0.363 0.0079/0.0143

5 x 4 x 8L 125-100-200L 0.21/0.373 0.0083/0.0147 0.21/0.373 0.0083/0.0147

5 x 4 x 10L 125-100-250L 0.21/0.373 0.0083/0.0147 0.21/0.373 0.0083/0.0147

5 x 4 x 13 125-100-315 0.21/0.373 0.0083/0.0147 0.21/0.373 0.0083/0.0147

5 x 4 x 13L 125-100-315L 0.23/0.393 0.0090/0.0155 0.23/0.393 0.0090/0.0155

5 x 4 x 16 125-100-400 0.20/0.363 0.0079/0.0143 0.20/0.363 0.0079/0.0143

5 x 4 x 16L 125-100-400L 0.21/0.373 0.0083/0.0147 0.21/0.373 0.0083/0.0147

6 x 5 x 10 150-125-250L 0.23/0.393 0.0090/0.0155 0.21/0.373 0.0083/0.0147

6 x 5 x 13L 150-125-315L 0.23/0.393 0.0090/0.0155 0.26/0.447 0.010/0.0176

6 x 5 x 6L 150-125-400L 0.24/0.427 0.0095/0.0168 0.26/0.447 0.010/0.0176

8 x 6 x 13L 200-150-315L 0.26/0.447 0.010/0.0176 0.26/0.447 0.010/0.0176

8 x 6 x 16L 200-150-400L 0.26/0.447 0.010/0.0176 0.26/0.447 0.010/0.0176

Diametral Hub Ring Clearance



Pumps


North American EuropeSpeed RPM

D2 max. at 60 Hz

% mm in.

2 x 1-1/4 x 8 50-32-200 3600 95 195.5 7.6968

2-1/2 x 1-1/2- x 10 65-40-250 3600 95 230 9.055

2-1/2 x 2 x 8L 65-50-200L 3600 95 211 8.3071

2-1/2 x 2 x 10L 65-50-250L 3600 84 200 7.874

3 x 2-1/2 x 5 80-65-125 3600 85 120.5 4.7441

3 x 2-1/2 x 6 80-65-160 3600 95 166 6.5354

3 x 2-1/2 x 10L 80-65-250L 3600 84 215 8.4646

5 x 4 x 10L 125-100-250L 3600 95 250 9.8425

Diameter Limitation for 60 Hz

North American Europe Inches (mm)

2 x 1¼ - 5 50-32-125 0.24 6

2 x 1¼ - 6 50-32-160 0.20 5

2 x 1¼ - 8 50-32-200 0.10 2.5

2 x 1¼ - 8L 50-32-200L 0.10 2.5

2½ x 1½ - 5 65-40-125 0.35 9

2½ x 1½ - 6 65-40-160 0.28 7

2½ x 1½ - 8L 65-40-200L 0.20 5

2½ x 1½ - 10 65-40-250 0.16 4

2½ x 1½ - 10L 65-40-250L 0.16 4

2½ x 2 - 5 65-50-125 0.39 10

2½ x 2 - 6 65-50-160 0.47 12

2½ x 2 - 8L 65-50-200L 0.35 9

2½ x 2 - 10L 65-50-250L 0.24 6

3 x 2½ - 5 80-50-125 0.59 15

3 x 2½ - 6 80-65-160 0.47 12

3 x 2½ - 8L 80-65-200L 0.35 9

3 x 2½ - 10L 80-65-250L 0.47 12

3 x 2½ - 13L 80-65-315L 0.35 9

4 x 3 - 6 100-80-160 0.63 16

4 x 3 - 8L 100-80-200L 0.39 10

4 x 3 - 10L 100-80-250L 0.39 10

4 x 3 - 13 100-80-315 0.43 11

5 x 4 - 8L 125-100-200L 0.43 11

5 x 4 - 10L 125-100-250L 0.79 20

5 x 4 - 13 125-100-315 0.67 17

5 x 4 - 13L 125-100-315L 0.67 17

5 x 4 - 16 125-100-400 0.51 13

5 x 4 - 16L 125-100-400L 0.51 13

6 x 5 - 10L 150-125-250L 0.55 14

6 x 5 - 13L 150-125-315L 0.59 15

6 x 5 - 16L 150-125-400L 0.75 19

8 x 6 - 13L 200-150-315L 0.71 18

8 x 6 - 16L 200-150-400L 0.75 19

Maximum Sphere Diameter



Pumps


North American EuropeSpeed RPM

Min. flow as% of BEP

Min. flow as% of BEP

2-1/2 x 1-1/2- x 10 65-40-250 3600 70 120

2-1/2 x 2 x 8L 65-50-200L 3600 50 120

3 x 2-1/2 x 10L 80-65-250L 3600 50 120

4 x 3 x 6 100-80-160 3600 50 120

5 x 4 x 10L 125-100-250L 3600 60 120

6 x 5 x 10 150-125-250L 1750 65 120

6 x 5 x 6L 150-125-400L 1750 70 120

8 x 6 x 16L 200-150-400L 1750 65 120

t. Minimum Flows

Between 40% of BEP and 130% of BEP without time limit.Except for the types of pump below with 60 Hz (Arnage only).



Pumps


v. Engineering Calculations and Correction Factors

The torques to be applied are:

Screw

Torque

Casing/cover Casing cover/Bearing

m.daN lbf.ft m.daN lbf.ft

HM 10 3 22 3 22

HM 12 5 37

HM 14 10 74 5 37

The tightening torques have been calculated as a function of the forces produced by the pumps. These torques correspond to a tension of the shaft end of 25% to 50% of the elastic limit.The tolerance allowed on the tightening torques is ± 30%.

Impeller Nut / Bolt

Frame DiameterTorque

m.daN lbf.ft

Frame 24 3/8" Bolt 1.6 12

Frame 32 1/2" Bolt 4 30

Frame 42 M24 Nut 16 118

Fastener Torques



Pumps


z. Casing Style/Flange Options/Thickness

Casing DataSingle volute, end suction, center line discharge•Foot supported, back pull-out design•Wear rings are optional (casing and casing cover)•

Casing Data Dimensions

Option Wear Ring



Pumps


Pump Size a h1 h2 m1 m2 n1 n2 b p s1 Gas Thread D Casing Thickness

North American Europe mm mm mm mm mm mm mm mm mm mm g k r mm Stainless Steel

Cast Iron

2 x 1-1/4 x 5 50-32-125 80 112 140 100 70 190 140 50 12 15 1/4" 1/4" 1/4" 150 9.0 8.0

2 x 1-1/4 x 6 50-32-160 80 132 160 100 70 240 190 50 12 15 1/4" 1/4" 1/4" 172.5 9.0 10.0

2 x 1-1/4 x 8 50-32-200 80 160 180 100 70 240 190 50 12 15 1/4" 1/4" 1/4" 220 10.0 11.0

2 x 1-1/4 x 8L 50-32-200L 80 160 180 100 70 240 190 50 14 15 1/4" 1/4" 1/4" 220 11.0 10.0

2-1/2 x 1-1/2 x 5 65-40-125 80 112 140 100 70 210 160 50 12 15 1/4" 1/4" 1/4" 150 9.0 10.0

2-1/2 x 1-1/2 x 6 65-40-160 80 132 160 100 70 240 190 50 12 15 1/4" 1/4" 1/4" 172.5 9.0 10.0

2-1/2 x 1-1/2 x 8L 65-40-200L 100 160 180 100 70 265 212 50 14 15 1/4" 1/4" 1/4" 220 10.0 10.0

2-1/2 x 1-1/2- x 10 65-40-250 100 180 225 125 95 320 250 65 14 15 1/4" 1/4" 1/4" 265 13.0 13.0

2-1/2 x 1-1/2 x 10L 65-40-250L 100 180 225 125 95 320 250 65 14 15 1/4" 1/4" 1/4" 265 12.5 13.0

2-1/2 x 2 x 5 65-50-125 100 132 160 100 70 240 190 50 12 15 1/4" 1/4" 1/4" 150 9.0 11.0

2-1/2 x 2 x 6 65-50-160 100 160 180 100 70 265 212 50 14 15 1/4" 1/4" 1/4" 177.5 9.5 12.0

2-1/2 x 2 x 8L 65-50-200L 100 160 200 100 70 265 212 50 14 15 1/4" 1/4" 1/4" 225 11.0 11.0

2-1/2 x 2 x 10L 65-50-250L 100 180 225 125 95 320 250 65 14 15 1/4" 1/4" 1/4" 265 12.0 12.0

3 x 2-1/2 x 5 80-65-125 100 160 180 125 95 280 212 65 14 15 1/4" 1/4" 1/4" 150 9.0 13.0

3 x 2-1/2 x 6 80-65-160 100 160 200 125 95 280 212 65 14 15 1/4" 1/4" 1/4" 177.5 9.5 13.0

3 x 2-1/2 x 8L 80-65-200L 100 180 225 125 95 320 250 65 14 15 1/4" 1/4" 1/4" 225 10.0 12.0

3 x 2-1/2 x 10L 80-65-250L 100 200 250 160 120 360 280 80 16 18 3/8" 3/8" 3/8" 265 11.5 13.0

3 x 2-1/2 x 13L 80-65-315 125 225 280 160 120 400 315 80 16 18 3/8" 3/8" 3/8" 337 15.5 17.0

4 x 3 x 6 100-80-160 125 180 225 125 95 320 250 65 14 15 1/4" 1/4" 1/4" 177.5 10.0 14.0

4 x 3 x 8L 100-80-200L 125 180 250 125 95 345 280 65 14 15 3/8" 3/8" 3/8" 245 11.0 13.0

4 x 3 x 10L 100-80-250L 125 200 280 160 120 400 315 80 16 18 3/8" 3/8" 3/8" 265 12.0 14.0

4 x 3 x 13 100-80-315 125 250 315 160 120 400 315 80 16 18 3/8" 3/8" 3/8" 337 15.0 18.0

5 x 4 x 8L 125-100-200L 125 200 280 160 120 360 280 80 16 18 3/8" 3/8" 3/8" 245 10.5 15.0

5 x 4 x 10L 125-100-250L 140 225 280 160 120 400 315 80 16 18 3/8" 3/8" 3/8" 300 11.0 15.0

5 x 4 x 13 125-100-315 140 250 315 160 120 400 315 80 16 18 3/8" 3/8" 3/8" 337 14.0 19.0

5 x 4 x 13L 125-100-315L 140 250 315 160 120 400 315 80 16 18 3/8" 3/8" 3/8" 337 14.5 18.0

5 x 4 x 16 125-100-400 140 280 355 200 150 500 400 100 20 22 1/2" 1/2" 1/2" 420 19.0 21.0

5 x 4 x 16L 125-100-400L 140 280 355 200 150 500 400 100 20 22 1/2" 1/2" 1/2" 395 18.0 20.0

6 x 5 x 10 150-125-250L 140 250 355 160 120 400 315 80 16 18 3/8" 3/8" 3/8" 300 12.0 18.0

6 x 5 x 13L 150-125-315L 140 280 355 200 150 500 400 100 20 22 1/2" 1/2" 1/2" 370 13.5 19.0

6 x 5 x 6L 150-125-400L 140 315 400 200 150 500 400 100 20 20 1/2" 1/2" 1/2" 425 15.5 21.0

8 x 6 x 13L 200-150-315L 160 280 400 200 150 550 450 100 20 22 1/2" 1/2" 1/2" 370 13.5 20.5

8 x 6 x 16L 200-150-400L 160 315 450 200 150 550 450 100 20 22 1/2" 1/2" 1/2" 425 17.0 22.0



Pumps


Pump Size a h1 h2 m1 m2 n1 n2 b p s1 Gas thread D Casing Thickness

g k rNorth American Europe in in in in in in in in in in mm Stainless Steel

Cast Iron

2 x 1-1/4 x 5 50-32-125 3.1 4.4 5.5 3.9 2.8 7.5 5.5 2.0 0.5 0.6 1/4" 1/4" 1/4" 5.9 0.35 0.31

2 x 1-1/4 x 6 50-32-160 3.1 5.2 6.3 3.9 2.8 9.4 7.5 2.0 0.5 0.6 1/4" 1/4" 1/4" 6.8 0.35 0.39

2 x 1-1/4 x 8 50-32-200 3.1 6.3 7.1 3.9 2.8 9.4 7.5 2.0 0.5 0.6 1/4" 1/4" 1/4" 8.7 0.39 0.43

2 x 1-1/4 x 8L 50-32-200L 3.1 6.3 7.1 3.9 2.8 9.4 7.5 2.0 0.6 0.6 1/4" 1/4" 1/4" 8.7 0.43 0.39

2-1/2 x 1-1/2 x 5 65-40-125 3.1 4.4 5.5 3.9 2.8 8.3 6.3 2.0 0.5 0.6 1/4" 1/4" 1/4" 5.9 0.35 0.39

2-1/2 x 1-1/2 x 6 65-40-160 3.1 5.2 6.3 3.9 2.8 9.4 7.5 2.0 0.5 0.6 1/4" 1/4" 1/4" 6.8 0.35 0.39

2-1/2 x 1-1/2 x 8L 65-40-200L 3.9 6.3 7.1 3.9 2.8 10.4 8.3 2.0 0.6 0.6 1/4" 1/4" 1/4" 8.7 0.39 0.39

2-1/2 x 1-1/2- x 10 65-40-250 3.9 7.1 8.9 4.9 3.7 12.6 9.8 2.6 0.6 0.6 1/4" 1/4" 1/4" 10.4 0.51 0.51

2-1/2 x 1-1/2 x 10L 65-40-250L 3.9 7.1 8.9 4.9 3.7 12.6 9.8 2.6 0.6 0.6 1/4" 1/4" 1/4" 10.4 0.49 0.51

2-1/2 x 2 x 5 65-50-125 3.9 5.2 6.3 3.9 2.8 9.4 7.5 2.0 0.5 0.6 1/4" 1/4" 1/4" 5.9 0.35 0.43

2-1/2 x 2 x 6 65-50-160 3.9 6.3 7.1 3.9 2.8 10.4 8.3 2.0 0.6 0.6 1/4" 1/4" 1/4" 7.0 0.37 0.47

2-1/2 x 2 x 8L 65-50-200L 3.9 6.3 7.9 3.9 2.8 10.4 8.3 2.0 0.6 0.6 1/4" 1/4" 1/4" 8.9 0.43 0.43

2-1/2 x 2 x 10L 65-50-250L 3.9 7.1 8.9 4.9 3.7 12.6 9.8 2.6 0.6 0.6 1/4" 1/4" 1/4" 10.4 0.47 0.47

3 x 2-1/2 x 5 80-65-125 3.9 6.3 7.1 4.9 3.7 11.0 8.3 2.6 0.6 0.6 1/4" 1/4" 1/4" 5.9 0.35 0.51

3 x 2-1/2 x 6 80-65-160 3.9 6.3 7.9 4.9 3.7 11.0 8.3 2.6 0.6 0.6 1/4" 1/4" 1/4" 7.0 0.37 0.51

3 x 2-1/2 x 8L 80-65-200L 3.9 7.1 8.9 4.9 3.7 12.6 9.8 2.6 0.6 0.6 1/4" 1/4" 1/4" 8.9 0.39 0.47

3 x 2-1/2 x 10L 80-65-250L 3.9 7.9 9.8 6.3 4.7 14.2 11.0 3.1 0.6 0.7 3/8" 3/8" 3/8" 10.4 0.45 0.51

3 x 2-1/2 x 13L 80-65-315 4.9 8.9 11.0 6.3 4.7 15.7 12.4 3.1 0.6 0.7 3/8" 3/8" 3/8" 13.3 0.61 0.67

4 x 3 x 6 100-80-160 4.9 7.1 8.9 4.9 3.7 12.6 9.8 2.6 0.6 0.6 1/4" 1/4" 1/4" 7.0 0.39 0.55

4 x 3 x 8L 100-80-200L 4.9 7.1 9.8 4.9 3.7 13.6 11.0 2.6 0.6 0.6 3/8" 3/8" 3/8" 9.6 0.43 0.51

4 x 3 x 10L 100-80-250L 4.9 7.9 11.0 6.3 4.7 15.7 12.4 3.1 0.6 0.7 3/8" 3/8" 3/8" 10.4 0.47 0.55

4 x 3 x 13 100-80-315 4.9 9.8 12.4 6.3 4.7 15.7 12.4 3.1 0.6 0.7 3/8" 3/8" 3/8" 13.3 0.59 0.71

5 x 4 x 8L 125-100-200L 4.9 7.9 11.0 6.3 4.7 14.2 11.0 3.1 0.6 0.7 3/8" 3/8" 3/8" 9.6 0.41 0.59

5 x 4 x 10L 125-100-250L 5.5 8.9 11.0 6.3 4.7 15.7 12.4 3.1 0.6 0.7 3/8" 3/8" 3/8" 11.8 0.43 0.59

5 x 4 x 13 125-100-315 5.5 9.8 12.4 6.3 4.7 15.7 12.4 3.1 0.6 0.7 3/8" 3/8" 3/8" 13.3 0.55 0.75

5 x 4 x 13L 125-100-315L 5.5 9.8 12.4 6.3 4.7 15.7 12.4 3.1 0.6 0.7 3/8" 3/8" 3/8" 13.3 0.57 0.71

5 x 4 x 16 125-100-400 5.5 11.0 14.0 7.9 5.9 19.7 15.7 3.9 0.8 0.9 1/2" 1/2" 1/2" 16.5 0.75 0.83

5 x 4 x 16L 125-100-400L 5.5 11.0 14.0 7.9 5.9 19.7 15.7 3.9 0.8 0.9 1/2" 1/2" 1/2" 15.6 0.71 0.79

6 x 5 x 10 150-125-250L 5.5 9.8 14.0 6.3 4.7 15.7 12.4 3.1 0.6 0.7 3/8" 3/8" 3/8" 11.8 0.47 0.71

6 x 5 x 13L 150-125-315L 5.5 11.0 14.0 7.9 5.9 19.7 15.7 3.9 0.8 0.9 1/2" 1/2" 1/2" 14.6 0.53 0.75

6 x 5 x 6L 150-125-400L 5.5 12.4 15.7 7.9 5.9 19.7 15.7 3.9 0.8 0.8 1/2" 1/2" 1/2" 16.7 0.61 0.83

8 x 6 x 13L 200-150-315L 5.5 11.0 15.7 7.9 5.9 21.7 17.7 3.9 0.8 0.9 1/2" 1/2" 1/2" 14.6 0.53 0.81

8 x 6 x 16L 200-150-400L 6.3 12.4 17.7 7.9 5.9 21.7 17.7 3.9 0.8 0.9 1/2" 1/2" 1/2" 16.7 0.67 0.87



Pumps


Pump Size Standard Construction Optional Construction


Flanges PN Flanges

Suction Discharge ANSI 125 ANSI 250

2 x 1-1/4 x 5 50-32-125 PN10/16 PN10/16 Yes Yes

2 x 1-1/4 x 6 50-32-160 PN10/16 PN10/16 Yes Yes

2 x 1-1/4 x 8 50-32-200 PN10/16 PN10/16 Yes Yes

2 x 1-1/4 x 8L 50-32-200L PN10/16 PN10/16 Yes Yes

2-1/2 x 1-1/2 x 5 65-40-125 PN10/16 PN10/16 Yes Yes

2-1/2 x 1-1/2 x 6 65-40-160 PN10/16 PN10/16 Yes Yes

2-1/2 x 1-1/2 x 8L 65-40-200L PN10/16 PN10/16 Yes Yes

2-1/2 x 1-1/2- x 10 65-40-250 PN10/16 PN10/16 Yes Yes

2-1/2 x 1-1/2 x 10L 65-40-250L PN10/16 PN10/16 Yes Yes

2-1/2 x 2 x 5 65-50-125 PN10/16 PN10/16 Yes Yes

2-1/2 x 2 x 6 65-50-160 PN10/16 PN10/16 Yes Yes

2-1/2 x 2 x 8L 65-50-200L PN10/16 PN10/16 Yes Yes

2-1/2 x 2 x 10L 65-50-250L PN10/16 PN10/16 Yes Yes

3 x 2-1/2 x 5 80-65-125 PN10/16 PN10/16 Yes Yes

3 x 2-1/2 x 6 80-65-160 PN10/16 PN10/16 Yes Yes

3 x 2-1/2 x 8L 80-65-200L PN10/16 PN10/16 Yes Yes

3 x 2-1/2 x 10L 80-65-250L PN10/16 PN10/16 Yes Yes

3 x 2-1/2 x 13L 80-65-315 PN10/16 PN10/16 Yes Yes

4 x 3 x 6 100-80-160 PN10/16 PN10/16 Yes Yes

4 x 3 x 8L 100-80-200L PN10/16 PN10/16 Yes Yes

4 x 3 x 10L 100-80-250L PN10/16 PN10/16 Yes Yes

4 x 3 x 13 100-80-315 PN10/16 PN10/16 Yes Yes

5 x 4 x 8L 125-100-200L PN10/16 PN10/16 Yes Yes

5 x 4 x 10L 125-100-250L PN10/16 PN10/16 Yes Yes

5 x 4 x 13 125-100-315 PN10/16 PN10/16 Yes Yes

5 x 4 x 13L 125-100-315L PN10/16 PN10/16 Yes Yes

5 x 4 x 16 125-100-400 PN10/16 PN10/16 Yes Yes

5 x 4 x 16L 125-100-400L PN10/16 PN10/16 Yes Yes

6 x 5 x 10 150-125-250L PN10/16 PN10/16 Yes Yes

6 x 5 x 13L 150-125-315L PN10/16 PN10/16 Yes Yes

6 x 5 x 6L 150-125-400L PN10/16 PN10/16 Yes Yes

8 x 6 x 13L 200-150-315L PN10 PN10/16 Yes Yes

8 x 6 x 16L 200-150-400L PN10 PN10/16 Yes Yes

Pump Casing Flange



Pumps


Flange Dimension Data PN10/PN16

North American EuropeSuction Discharge

DNA DNRmm in. mm in.

2 x 1-1/4 x 5 50-32-125 50 2 32 1-1/42 x 1-1/4 x 6 50-32-160 50 2 32 1-1/42 x 1-1/4 x 8 50-32-200 50 2 32 1-1/42 x 1-1/4 x 8L 50-32-200L 50 2 32 1-1/4

2-1/2 x 1-1/2 x 5 65-40-125 65 2-1/2 40 1-1/22-1/2 x 1-1/2 x 6 65-40-160 65 2-1/2 40 1-1/2

2-1/2 x 1-1/2 x 8L 65-40-200L 65 2-1/2 40 1-1/22-1/2 x 1-1/2- x 10 65-40-250 65 2-1/2 40 1-1/22-1/2 x 1-1/2 x 10L 65-40-250L 65 2-1/2 40 1-1/2

2-1/2 x 2 x 5 65-50-125 65 2-1/2 50 22-1/2 x 2 x 6 65-50-160 65 2-1/2 50 22-1/2 x 2 x 8L 65-50-200L 65 2-1/2 50 22-1/2 x 2 x 10L 65-50-250L 65 2-1/2 50 23 x 2-1/2 x 5 80-65-125 80 3 65 2-1/23 x 2-1/2 x 6 80-65-160 80 3 65 2-1/23 x 2-1/2 x 8L 80-65-200L 80 3 65 2-1/23 x 2-1/2 x 10L 80-65-250L 80 3 65 2-1/23 x 2-1/2 x 13L 80-65-315 80 3 65 2-1/2

4 x 3 x 6 100-80-160 100 4 80 34 x 3 x 8L 100-80-200L 100 4 80 34 x 3 x 10L 100-80-250L 100 4 80 34 x 3 x 13 100-80-315 100 4 80 35 x 4 x 8L 125-100-200L 125 5 100 45 x 4 x 10L 125-100-250L 125 5 100 45 x 4 x 13 125-100-315 125 5 100 45 x 4 x 13L 125-100-315L 125 5 100 45 x 4 x 16 125-100-400 125 5 100 45 x 4 x 16L 125-100-400L 125 5 100 46 x 5 x 10 150-125-250L 150 6 125 56 x 5 x 13L 150-125-315L 150 6 125 56 x 5 x 6L 150-125-400L 150 6 125 58 x 6 x 13L 200-150-315L 200 8 150 68 x 6 x 16L 200-150-400L 200 8 150 6

PN10 / 16 PN10mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in.

DN 32 1"1/4 40 1"1/2 50 2" 65 2"1/2 80 3" 100 4" 125 5" 150 6" 200 8"V 76 3.0 84 3.3 99 3.9 118 4.6 132 5.2 156 6.1 184 7.2 211 8.3 266 10.5W 100 3.9 110 4.3 125 4.9 145 5.7 160 6.3 180 7.1 210 8.3 240 9.4 295 11.6Y 140 5.5 150 5.9 165 6.5 185 7.3 200 7.9 220 8.7 250 9.8 285 11.2 340 13.4Z 4 0.2 4 0.2 4 0.2 4 0.2 8 0.3 8 0.3 8 0.3 8 0.3 8 0.3d1 19 0.7 19 0.7 19 0.7 19 0.7 19 0.7 19 0.7 19 0.7 23 0.9 23 0.9



Pumps

MEN Standard Lead Times

Standard Lead TimesInformation not provided



Pumps

MEN Standard Lead Times




Pumps

MEN Typical Specifications

Typical Specifications

GeneralFurnish and install a Flowserve model MEN centrifugal pump for ________ service. The pump is to be cast iron construction with bronze impeller and is to be mounted on a steel baseplate extending under the pump and motor drive. The pump is to be mounted to the driver by means of a woods or approved equal coupling and protected by a polymer split coupling guard.

Operating ConditionsEach pump shall be rated ______ USGPM at ______ feet of total developed head, at ______ RPM, minimum ______ % efficiency at full speed. Minimum shut off head shall be ______ feet, and BHP to run out shall not exceed ______, and in no event shall BHP exceed HP rating of motor furnished at 1.0 service factor. Net positive suction head to the centerline of the impeller shall be ______ feet. Any further characteristics of the fluid should also be specified:

PH: _______Temperature: _________ Specific Gravity: _______Solids Present: ________% Solids by Wt. ________Viscosity @ Pumped Temperature: __________

CasingThe casing shall be close grained cast iron ASTM A48 class 35, self venting, and top centerline discharge design. The casing shall be designed to permit disassembly from the rear to remove pump internals without disturbing the system piping, and be supported by casing feet. Drain and gauge connections shall be supplied. In addition, a horizontal priming or filling port shall be supplied in the casing volute. The casing shall be rated for 230 PSI of working pressure.

Casing NozzlesFlanged casing nozzles shall conform to ANSI B16.1 specification with a minimum 125# rating. All flanged connections shall be flat face.

Stuffing BoxThe stuffing box shall be designed as an open seal chamber to allow maximum flushing action at the mechanical seal faces. The mechanical seal chamber shall be vented to suction pressure and sealed from discharge by back ring faces.

Mechanical SealThe mechanical seal shall be a Flowserve internal elastomeric bellows – non pusher design type 220. Mechanical seal rotating parts shall be stainless steel with carbon vs. ceramic faces and EPDM bellows.

ImpellerThe extended hub impeller shall be bronze, C90800-B427 of the enclosed design, hydraulically and dynamically balanced. Impeller shall be balanced to ISO 1940 G6.3 or higher standard. The impeller shall be securely positioned on the shaft by means of an impeller key. Balance holes shall be provided through the impeller hub to minimize axial thrust loads and keep stuffing box pressure to a minimum. The impeller shall include an integral one-piece extended hub through the stuffing box to prevent leakage and eliminate the stack-up of tolerances and run out at the mechanical seal.

ShaftThe pump shaft shall be high strength 13% chrome, AISI 420F and provide a minimum of shaft deflection. The shaft shall be of dry construction sealed from the pumped fluid.

Bearing FrameThe bearing frame shall be close grained cast iron, one piece design to eliminate stack-up of tolerance at the mechanical seal faces. The bearing frame shall have a registered fit to the cover and / or casing to ensure reassembly of the pump after it has been serviced.

BearingsThe shaft shall be supported by two anti-friction ball bearings located in the pump bearing frame. Both bearings shall be sealed-for-life type, which will not require re-lubrication and will be adequately protected from entrance of contaminated material while operating.

Factory TestingOne pump of each size and rating shall be tested in accordance with the latest standards of the Hydraulic Institute (H.I.), using calibrated shop drivers and instrumentation. All instrumentation shall have been calibrated within the time frame as specified by H.I. H.I. shall govern acceptable tolerances. No negative tolerances will be accepted in any event.

BaseplateThe baseplate shall be of channel steel sufficiently designed to support the pump and the driving motor.

CouplingThe coupling shall be Woods or equal, of the flexible spacer type to allow removal of the pump internals without disconnecting motor leads or system piping.

ManufacturersPlans and specifications were developed basis Flowserve model _______________ pumps. Other manufactures are acceptable provided equipment is modified to meet these specifications and a submittal is approved by the engineer. Should use of other manufactures result in changes to piping or structures, such changes must be approved by the engineer, and there shall be no additional cost to the owner for such changes.



Pumps

MEN Typical Specifications




Pumps

MEN Typical Applications

Typical Applications

Water supplyWatering, irrigation•Raising, draining, exhaure•Air conditioning•Swimming pools, fountains•Fire service•Hot water circulation up to 140°C (284°F) (consult the factory)•

IndustryServices•Cooling•Lubrication•Surface treatment•Washing machines•Sea water and diverse liquids (consult us)•



Pumps

MEN Typical Applications




Pumps

MEN Representative Installation Lists

Representative Installations ListInformation not provided



Pumps

MEN Representative Installation Lists




Pumps

MEN Competitive Analysis

Competitive AnalysisInformation not provided



Pumps

MEN Competitive Analysis




Pumps

MEN Coverage Charts

50 Hz (For the final choice of the MEN pump – See PROS characteristics curves)


2 x 1-1/4 x 5 50-32-125

2 x 1-1/4 x 6 50-32-160

2 x 1-1/4 x 8 50-32-200

2 x 1-1/4 x 8L 50-32-200L

2-1/2 x 1-1/2 x 5 65-40-125

2-1/2 x 1-1/2 x 6 65-40-160

2-1/2 x 1-1/2 x 8L 65-40-200L

2-1/2 x 1-1/2- x 10 65-40-250

2-1/2 x 1-1/2 x 10L 65-40-250L

2-1/2 x 2 x 5 65-50-125

2-1/2 x 2 x 6 65-50-160

2-1/2 x 2 x 8L 65-50-200L

2-1/2 x 2 x 10L 65-50-250L

3 x 2-1/2 x 5 80-65-125

3 x 2-1/2 x 6 80-65-160

3 x 2-1/2 x 8L 80-65-200L

3 x 2-1/2 x 10L 80-65-250L

3 x 2-1/2 x 13L 80-65-315

4 x 3 x 6 100-80-160

4 x 3 x 8L 100-80-200L

4 x 3 x 10L 100-80-250L

4 x 3 x 13 100-80-315

5 x 4 x 8L 125-100-200L

5 x 4 x 10L 125-100-250L

5 x 4 x 13 125-100-315

5 x 4 x 13L 125-100-315L

5 x 4 x 16 125-100-400

5 x 4 x 16L 125-100-400L

6 x 5 x 10 150-125-250L

6 x 5 x 13L 150-125-315L

6 x 5 x 6L 150-125-400L

8 x 6 x 13L 200-150-315L

8 x 6 x 16L 200-150-400L



Pumps

MEN Coverage Charts

60 Hz (For the final choice of the MEN pump – See PROS characteristics curves)


2 x 1-1/4 x 5 50-32-125

2 x 1-1/4 x 6 50-32-160

2 x 1-1/4 x 8 50-32-200

2 x 1-1/4 x 8L 50-32-200L

2-1/2 x 1-1/2 x 5 65-40-125

2-1/2 x 1-1/2 x 6 65-40-160

2-1/2 x 1-1/2 x 8L 65-40-200L

2-1/2 x 1-1/2- x 10 65-40-250

2-1/2 x 1-1/2 x 10L 65-40-250L

2-1/2 x 2 x 5 65-50-125

2-1/2 x 2 x 6 65-50-160

2-1/2 x 2 x 8L 65-50-200L

2-1/2 x 2 x 10L 65-50-250L

3 x 2-1/2 x 5 80-65-125

3 x 2-1/2 x 6 80-65-160

3 x 2-1/2 x 8L 80-65-200L

3 x 2-1/2 x 10L 80-65-250L

3 x 2-1/2 x 13L 80-65-315

4 x 3 x 6 100-80-160

4 x 3 x 8L 100-80-200L

4 x 3 x 10L 100-80-250L

4 x 3 x 13 100-80-315

5 x 4 x 8L 125-100-200L

5 x 4 x 10L 125-100-250L

5 x 4 x 13 125-100-315

5 x 4 x 13L 125-100-315L

5 x 4 x 16 125-100-400

5 x 4 x 16L 125-100-400L

6 x 5 x 10 150-125-250L

6 x 5 x 13L 150-125-315L

6 x 5 x 6L 150-125-400L

8 x 6 x 13L 200-150-315L

8 x 6 x 16L 200-150-400L



Pumps

MEN Pump Selection Program Guidelines

Pump Selection Program Guidelines

SelectionStep1•

Key in input dataQuantity –Rated flow (m – 3/h)Rated TDH (m) –NPSH available (m) –Specific gravity –Suction conditions –Liquid –Units –Frequency –Material : FB1 Cast iron casing, Cast iron impeller – FB2 Cast iron casing, Bronze impeller

Step 2•Various selections will be presented to you –Chose the most suitable one depending on the criteria are most –important to your customer



Pumps

MEN Pump Selection Program Guidelines




Pumps

MEN Drivers, Mechanical Seals and Accessory Information

Drivers, Mechanical Seals and Accessory InformationInformation not provided



Pumps

MEN Drivers, Mechanical Seals and Accessory Information




Pumps

MEN Optional and Alternative Configurations

Optional and Alternative ConfigurationsInformation not provided



Pumps

MEN Optional and Alternative Configurations




Pumps

MEN Aftermarket and Recommended Spare Parts

Recommended Spare PartsRecommended spare parts for 2 years of operation

Ordering of SparesFlowserve keeps records of all pumps that have been supplied. When ordering spares the following information should be quoted:

1) Pump serial number2) Pump size3) Part name4) Part number5) Number of parts required

The pump size and serial number are shown on the pump nameplate.

Spare Parts Item

Number of pumps in operation

1 2 3 4 5 6 or more

Quantity of spare parts

Set of bearings [3011] 1 1 2 2 3 50%

Casing gaskets [4590-03] 2 4 6 8 10 150%

Other gaskets [4590-01] & [02] 1 2 3 4 5 100%

Mechanical seal [4200] 1 1 1 2 2 30%

Gland packing (option) [4130] 2 3 4 5 6 130%

Casing wear rings (option) [1500] 1 1 2 2 3 50%

To ensure continued satisfactory operation, replacement parts to the original design specification should be obtained from Flowserve. Any change to the original design specification (modification or use of a non-standard part) will invalidate the pump’s safety certification.

Storage of SparesSpares should be stored in a clean dry area away from vibration. Inspection and re-treatment of metallic surfaces (if necessary) with preservative is recommended at 6 monthly intervals.



Pumps


Bearing Frame Size

Pump Size Inlet-Outlet-Max Imp Dia

Pump Casing [1110]

Impeller [2250]

Casing Cover Gland

Packing [1221-

01]

Casing Cover FMI

Mech. Seal

[1221- 02]

Casing Cover FMI

Mech. Seal

[1221- 03]

Gasket [4590-

03]

Shaft Sleeve Gland

Packing [2450]

Pump Shaft

[2110]

Gland [4120]

Mech. Seal

[4200]

Bearing Housing [3200]

Radial Ball

Bearing [3011]

24


2 x 1-1/4 x 5 50-32-125 1 1 1 1 1 1 1 1 1 1 1 1

2 x 1-1/4 x 6 50-32-160 2 2 3 3 3 2 1 1 1 1 1 1

2 x 1-1/4 x 8 50-32-200 3 3 6 6 6 4 1 1 1 1 1 1

2 x 1-1/4 x 8L 50-32-200L 4 4 6 6 6 4 1 1 1 1 1 1

2-1/2 x 1-1/2 x 5 65-40-125 5 5 1 1 1 1 1 1 1 1 1 1

2-1/2 x 1-1/2 x 6 65-40-160 6 6 3 3 3 2 1 1 1 1 1 1

2-1/2 x 1-1/2 x 8L 65-40-200L 7 7 6 6 6 4 1 1 1 1 1 1

2-1/2 x 1-1/2- x 10 65-40-250 8 8 7 7 7 7 1 1 1 1 1 1

2-1/2 x 1-1/2 x 10L 65-40-250L 9 9 7 7 7 7 1 1 1 1 1 1

2-1/2 x 2 x 5 65-50-125 10 10 2 2 2 1 1 1 1 1 1 1

2-1/2 x 2 x 6 65-50-160 11 11 4 4 4 3 1 1 1 1 1 1

2-1/2 x 2 x 8L 65-50-200L 12 12 8 8 8 5 1 1 1 1 1 1

2-1/2 x 2 x 10L 65-50-250L 13 13 7 7 7 7 1 1 1 1 1 1

3 x 2-1/2 x 5 80-65-125 14 14 2 2 2 1 1 1 1 1 1 1

3 x 2-1/2 x 6 80-65-160 15 15 5 5 5 3 1 1 1 1 1 1

3 x 2-1/2 x 8L 80-65-200L 16 16 8 8 8 5 1 1 1 1 1 1

32

4 x 3 x 6 100-80-160 17 17 10 10 10 3 2 2 2 2 2 2

3 x 2-1/2 x 13L 80-65-250L 18 18 12 12 12 8 2 2 2 2 2 2

4 x 3 x 6 80-65-315 19 19 5 5 5 10 1 1 1 1 1 1

4 x 3 x 8L 100-80-200L 20 20 9 9 9 6 2 2 2 2 2 2

4 x 3 x 10L 100-80-250L 21 21 10 10 10 8 2 2 2 2 2 2

4 x 3 x 13 100-80-315 22 22 12 12 12 10 2 2 2 2 2 2

5 x 4 x 8L 125-100-200L 23 23 9 9 9 6 2 2 2 2 2 2

5 x 4 x 10L 125-100-250L 24 24 11 11 11 9 2 2 2 2 2 2

5 x 4 x 13 125-100-315 25 25 13 13 13 10 2 2 2 2 2 2

5 x 4 x 13L 125-100-315L 26 26 13 13 13 10 2 2 2 2 2 2

42

5 x 4 x 16 150-125-250L 27 27 14 14 14 9 3 3 3 3 3 3

5 x 4 x 16L 125-100-400 28 28 15 15 15 13 3 3 3 3 3 3

6 x 5 x 10 125-100-400L 29 29 11 11 11 12 2 2 2 2 2 2

6 x 5 x 13L 150-125-315L 30 30 16 16 16 11 3 3 3 3 3 3

6 x 5 x 6L 150-125-400L 31 31 17 17 17 14 3 3 3 3 3 3

8 x 6 x 13L 200-150-315L 32 32 16 16 16 11 3 3 3 3 3 3

8 x 6 x 16L 200-150-400L 33 33 17 17 17 14 3 3 3 3 3 3

[1110] = Part number in sectional drawing and parts list

MEN Pump Interchangeability ChartPer column, same number corresponds to same component.



Pumps


Pump NomenclatureThe following example explains how the pump name identifies the construction features:

MEN Europe – 65-40-250LNorth American – 2-1/2 x 1-1/2 x 10L

Each pump is supplied with one of the following nameplates:

Memphis Tn USA 1-800-343-7867

Job 1234567Serial Number 12345678901

Pump type

Speed of rotation

Flow rate

Year of construction + Manufacture number

Head

Radial/thrust bearing

Mass

Maximum admissible Pressure at 20°C (68°F)

Maximum/minimum temperature

CE marked pump units are supplied with the following nameplate:

Mass of the set

kg



Pumps





Pumps

MEN FAQs (Frequently Asked Questions)

FAQs (Frequently Asked Questions)Information not provided



Pumps

MEN FAQs (Frequently Asked Questions)




Pumps

MEN Typical Instructional Manual

Typical User Instructions (formerly IOMs)Information not provided



Pumps

MEN Typical Instructional Manual

Faults: Causes and Remedies

Insufficient flow rate Irregular pump running Driver overloaded Mechanical seal leak Equipment vibration Excessive pump casing temperature

Possible Causes Solutions

• • • • Pump or suction pipe not completely filled - Check and complete filling• • • Air bubbles in pipes - Check and desecrate the pipes

• • • Suction level too low

- Check: the available NPSH > the required NPSH - Reduce geometrical suction lift- Reduce head losses in pipes and in fittings (diameter increase and appropriate fitting positions)- Check valves and strainers- Check the immersion head of the suction valve

• • Wrong rotation - Reverse 2 phases on motor terminal boxes• • • The motor is running on 2 phases only - Check and control the motor electrical power supply• Motor running too low - Check the connection in the terminal box according to the voltage

• • Total manometric head system higher than pump differential head

- Check the discharge head- Check the head losses in discharge pipes (partly closed valve, foreign particles, back pressure too high)- Modify the installation or change the pump set

• • Total manometric head system lower than pump differential head

-Throttle at discharge valve or trim the impeller (contact our local agent): - Consult Flowserve

• • • Pipes (valves, filter...) - Control, dismantle and clean• • Insufficient flow rate - Check the suction and discharge pipes (valves, back pressure)

• Worn wear-ring surfaces - Foresee pump mending. Consult Flowserve• • • • Seizure, jamming - Consult Flowserve

• • • • Excessive strains on flanges - Check the flange connections and eliminate strains (pipe positioning or elastic sleeves mounting)

• Defective mechanical seal- Check and replace all the mechanical seal parts - Mechanical seal: Consult Flowserve

• • • • Defective motor bearings - Consult Flowserve• • Specific gravity or viscosity of liquid too high - Consult our local agent to analyze the problem

• Misalignment - Check the alignment of the pump and of its driver• Foundations not sufficiently rigid - Check the setting of base plates: tightening, bad adjustment, seal

Insufficient pressure

Pump looses prime after starting

Possible Causes Solutions

• Rotation speed too low (check the driver) - Check the connection in the terminal box according to the voltage

• • Presence of air - Check and de-aerate

• Suction pressure insufficient - Check: the available NPSH > the required NPSH

• Mechanical defects - Consult Flowserve

• Air leak in the suction pipe - Check suction pipe is airtight

• Restriction in suction pipe - Check diameter of suction pipe

• Suction level too low

- Check the available NPSH > the required NPSH - Reduce geometrical suction lift- Reduce head losses in pipes and in fittings (diameter increase and appropriate fitting positions)- Check valves and strainers- Check the immersion head of the suction valve

Obstruction of suction pipe - Check condition of pipe

• Defective gland packing on the shaft- Check the screwing of the gland and the gland packing.- Check and replace all the gland packing. Never run dry- Mechanical seal: Consult Flowserve

• Defective gasket - Consult Flowserve



Pumps

MEN Submittal Documentation (Software)

Submittal Documentation (Software)Information not provided



Pumps

MEN Submittal Documentation (Software)




Pumps

MEN Testing Capabilities

Testing Capabilities NDE a. Information not provided

Performance b. Information not provided

Hydro c. Information not provided

Special d. Information not provided

Inspection definitions and issues e. Information not provided

Witness test guidelines and safety f. Information not provided



Pumps

MEN Testing Capabilities




Pumps

MEN Pricing for Pumps, Parts and Accessories

Pricing for Pumps, Parts and AccessoriesTo obtain current pricing on this pump, including parts and a. accessories, please refer to PROS+. a free copy of PROS+ may be ordered or downloaded from Flowserve.com Information not provided

Discount Schedules and Pricing b. Information not provided



Pumps

MEN Pricing for Pumps, Parts and Accessories


12/0824-1

Pumps

MEN Terms and ConditionsRev. 4 January 11, 2008

24-1 Type MEN End-Suction Water Pump


1. Applicability:

Except for the application of overriding General Terms Agreements previously executed between Buyer and Seller, any purchase order covering the sale of Seller’s equipment or services (“Order”) shall be governed solely by these Conditions of Sale and other written provisions mutually agreed upon. Any oral understandings are expressly excluded. Seller shall not be deemed to have waived these Conditions of Sale if it fails to object to provisions appearing on, incorporated by reference in, or attached to Buyer’s Purchase Order Form which provisions are hereby expressly rejected. Buyers’ silence or acceptance or use of products constitutes its acceptance of these Conditions of Sale. No modification or addition to these Conditions of Sale shall be effective unless agreed to in writing and signed by an authorized representative of Buyer and Seller. Seller reserves the right to reject any Order submitted for its acceptance.

2. Definitions:

“Order” means any purchase order covering the sale of Seller’s equipment or services.

“Equipment” means all equipment and parts manufactured by Seller.

“Buyer” means the company who accepted Seller’s offer or is named in the Purchase Order.

“Services” means work, direction of work, technical information or technical consulting and advice or other services furnished by Seller to Buyer and may support such activities as the installation, testing, alignment, startup, operation, repair and maintenance of the Equipment.

“Seller” means the company named on the offer.

“Suppliers” means any of Seller’s suppliers of material or services for the Equipment or Services, regardless of tier.

3. Delivery:

Delivery of the Equipment hereunder shall be made Ex-works (Incoterms 2000) Seller’s plant. Shipping dates are approximate and are based on prompt receipt of all necessary information at Seller’s plant. In case of delay in furnishing complete information, dates of shipment may be extended for a reasonable time based on conditions at Seller’s plant. In the event Seller provides transport services these will be quoted as a lump sum price based on destination and shipping mode.

Seller shall not be liable for delay in delivery due to causes beyond its reasonable control including but not limited to, acts of God, acts of government, acts of Buyer, fires, labor disputes, boycotts, floods, epidemics, quarantine restrictions, war, insurrection, riot, civil or military authority, freight embargoes, transportation shortages or delays, unusually severe weather or inability to obtain necessary labor, materials or manufacturing facilities due to such causes. In the event of any such delay, the date of delivery shall be extended for a length of time equal to the period of the delay.

In the event Buyer requests a delay in completion and shipment of the Equipment or any part thereof for any reason, the parties shall agree upon any cost and/or scheduling impact of such delay, with such costs to the account of Buyer. Any delay period beyond thirty (30) days after original scheduled shipment date shall require Buyer to take title and risk of loss of such Equipment, thereafter to make arrangements for storage of such Equipment with the Seller or other party. Seller’s invoice, which is contractually based on shipment, shall be issued upon Seller’s readiness to ship the original Equipment.

4. Warranty:

“Nonconformance” means failure to comply with, or failure to operate due to noncompliance with, applicable Seller drawings or having defects in workmanship or material. Normal wear and tear, erosion, corrosion and the need for regular overhaul and periodic maintenance do not constitute a Nonconformance.

Seller warrants at time of shipment to Buyer its Equipment will comply with applicable Seller drawings and will be free from defects in workmanship and material. Any equipment and parts supplied by Seller but manufactured by third parties carry the warranty that the manufacturer of such equipment and parts conveyed to Seller which can be passed on to Buyer. These warranties run to the Buyer, its successors, assigns, and customers. Supplier’s obligations under this warranty shall expire one (1) year from initial startup or use of the Equipment or eighteen (18) months after shipment, whichever occurs first. Seller warrants that the Services shall be performed in accordance with industry practices. Seller’s warranty obligation for service work shall expire ninety (90) days from the date of the initial start-up or six (6) months after completion of the service work, whichever occurs first.

Buyer must notify Seller in writing during the defects liability period of a Nonconformance and, within 30 calendar days of discovery of the Nonconformance.

Seller’s obligation and Buyer’s sole remedy under this defects liability period is repair or replacement, at Seller’s election, of any Equipment Nonconformance. All Equipment repaired or replaced will be warranted only for the unexpired portion of the original defects liability period.

Seller agrees to repair or replace Ex-works Seller’s plant any Equipment or part thereof manufactured by Seller which does not conform to the warranty for Equipment. Equipment claimed to be defective must be returned, freight prepaid and allowed by Buyer and in accordance with Seller’s instructions to the point of manufacture, unless Seller directs otherwise. Title to and risk of loss of any equipment being repaired shall remain with Buyer at all times.

In connection with the performance of any corrective work, all removal and reinstallation of the Equipment shall be performed by Buyer at its expense. Buyer shall, at its expense, be responsible for removing, reinstalling, replacing or supplying any equipment, materials or structures which are necessary to provide reasonable access to the Equipment to be repaired or replaced. Any decontamination or radiation protection necessary in connection with the removal/reinstallation or on-site repair of the Equipment shall be performed by Buyer without cost to Seller.

Seller will not be liable under this warranty if the Equipment has been exposed or subjected to any (1) maintenance, repair, installation, handling, packaging, transportation, storage, operation or use which is improper or otherwise not in compliance with Seller’s instructions; (2) alteration, modification or repair by anyone other than Seller or those specifically authorized by Seller, (3) accident, contamination, foreign object damage, abuse, neglect or negligence after shipment to Buyer; (4) damage caused by failure of a Seller supplied Product not under warranty or by any hardware or software not supplied by Seller; (5) use of counterfeit or replacement parts that are neither manufactured nor approved by Seller for use in the Equipment; or (6) Equipment which is normally consumed in operation or which have normal life inherently shorter than the warranty period including, but not limited to, consumables (e.g. flashtubes, lamps, batteries, storage capacitors).

THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER WRITTEN, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, AND FITNESS FOR PARTICULAR PURPOSE.

5. Payment:

All prices are net cash 30 days from date of invoice, unless otherwise stated in Seller’s proposal, quotation, or offer. Should Buyer for any reason default in the payment of the contract of purchase, Buyer agrees to pay all collection costs, attorney fees and expenses incurred in collecting payment, including interest on the amount due at the maximum legal rate. All transportation, insurance and similar charges incident to delivery shall be paid by Buyer. Seller shall issue its invoice upon shipment, or upon notice to Buyer that Seller is ready to ship, whichever is earlier. Depending on the value of the order, Seller may at its sole discretion require progress payments.

If Buyer’s financial condition is or becomes unsatisfactory to Seller, Seller reserves the right to: a) cancel shipment at any time prior to delivery of the Equipment without further obligation or liability on the Seller’s part (b) or require a letter of credit or other acceptable security before shipment.

WORLDWIDE TERMS AND CONDITIONS OF SALE

continued

12/0824-2

Pumps




6. Changes:

Buyer may request modifications as to the amount, scope and/or nature of the Equipment to be supplied by a written change request. Buyer may also request modifications, including but not limited to drawings, models, instructions, specifications, quantities, method of shipment, packing, place of delivery or delivery dates for the Equipment. If, in the opinion of Seller, any modification will affect the agreed fixed price and/or time of delivery, Seller will notify Buyer thereof in writing and will not be obligated to perform any modification unless agreed to by Seller. Buyer shall confirm that such change is authorized and accepted by issuing a Purchase Order revision.

7. Setoff:

All amounts that Buyer owes Seller under an Order shall be due and payable according to the terms of an Order. Buyer is prohibited from, and shall not set off such amounts or any portion thereof, whether or not liquidated, against sums which Buyer asserts are due it, its parent affiliates, subsidiaries or other divisions or units under other transactions with Seller, its parent affiliates, subsidiaries or other divisions or units.

8. Cancellation:

Buyer reserves the right to cancel any portion of an Order affected by a default of Seller or any insolvency or suspension of Seller’s operations or any petition filed or proceeding commenced by or against Seller under any state or federal law relating to bankruptcy, arrangement, reorganization, receivership or assignment for the benefit of creditors.

9. Non-Disclosure and Non-Use of Sellers’ Information:

Buyer agrees that it will not use Seller’s data for the manufacture or procurement of products which are the subject of an Order or any similar products, or cause said products to be manufactured by, or procured from, any other source or reproduce said data and information or otherwise appropriate them without the written authorization of the Seller. Buyer agrees that it will not disclose or make available to any third-party any of Seller’s data or other information pertaining to this Order which is proprietary to Seller without obtaining Seller’s prior written consent.

10. Patent Indemnity:

Except insofar as an Order calls for equipment pursuant to Buyer’s designs, drawings or specifications, Seller agrees to pay the amount of any final judgment against Buyer resulting from a suit claiming that any commercial equipment manufactured or furnished hereunder, by reason of their manufacture, sale or use, infringes any United States patent which has issued at date of an Order, and Buyer’s reasonable costs and expenses in defense of such suit if Seller does not undertake the defense thereof, provided Seller is promptly notified of the threat or commencement of such suit and is offered full and exclusive control to conduct the defense or settlement thereof.

Seller’s indemnity shall not apply where infringement would not have occurred from the normal use for which the equipment was designed. Seller’s liability for damages hereunder is limited to those computed solely on the value of any equipment sold to Buyer. In no event shall Seller be liable for consequential damages or costs applicable thereto. In the event of any claim that equipment furnished hereunder infringes any United States patent, Seller may at its option and expense (a) procure for Buyer the right to continue using the product, or (b) replace or modify the product so that it becomes non-infringing, or (c) grant Buyer a credit for such product, less a reasonable depreciation for use, damage, and obsolescence upon its return to Seller. Buyer agrees to pay all costs and expenses incurred by Seller in its defense and the amount of any judgment against Seller, in any suit or proceeding against Seller based upon a claim of infringement, resulting solely from the Buyer combining any equipment furnished hereunder with any item not manufactured or furnished by Seller or from the sale or use of any such combination by Buyer. Seller shall also indemnify Buyer’s customers and agents for such infringement if, and to the extent that, Buyer has agreed so to indemnify them, but to no greater extent than Seller has indemnified Buyer herein and under the same conditions as set forth herein. In the event any equipment to be furnished under this Order is to be made in accordance with drawings, samples or manufacturing specifications designated by Buyer and is not the design of Seller, Buyer agrees to defend, indemnity and hold Seller harmless to the same extent and subject to the same requirements as set forth in Seller’s obligation to Buyer as above. The above is in lieu of any other indemnity or warranty, express or implied by Seller, with respect to intellectual property (patents, trade secret, mask works, trademarks, copyrights, or the like).

11. Special Tooling and Data:

Unless otherwise agreed in writing, all material, software, data processes, equipment, facilities and special tooling, which term includes but is not limited to jigs, dies, fixtures, molds, patterns, special taps, special gages, special test equipment, other special equipment and manufacturing aids and replacements thereof, used in the manufacture of products covered by an Order shall be and remains the property of Seller. Seller retains all rights, title and interest in drawings, engineering instructions, specifications, and all other written data, if any, furnished with equipment.

12. Import Permit or License:

In the event an import permit or license is required by Buyer’s or End User’s authorities for the Equipment sold hereunder, performance is subject to Seller’s prior receipt of evidence satisfactory to Seller that an appropriate import permit or license has been granted. As to any such permit or license Buyer shall advise Seller of the validity, number, date of issue and whether the expiration date refers to clearance from the port of departure or arrival at the port of destination. Buyer assumes all responsibility for the procurement thereof and any expenses incurred therein related to any import permit or license. In the event currency exchange controls exist in Buyer’s country, Buyer shall so state.

13. Export License:

Unless otherwise agreed in writing, Buyer shall be responsible for compliance with the export control laws and regulations of the U.S. Government or the jurisdiction where Seller’s manufacturing facility accepting the Order is located, and when required by such laws and regulations shall obtain export and re-export licenses required for goods, services and technical data delivered under an Order. Seller shall not be liable to Buyer for any failure to provide goods, services or technical data as a result of any of the following governmental actions: (1) refusal to grant export or re-export license; (2) cancellation of export or re-export license, or (3) any subsequent interpretation of the export laws and regulations, after the date of an Order, that limits or has a material adverse effect on the cost of Seller’s performance on an Order. Seller’s performance hereunder is subject to Seller’s prior receipt of evidence satisfactory to Seller that an appropriate export license has been granted. If Seller assists in obtaining any export license, Buyer shall reimburse Seller for all expenses.

14. Taxes:

Seller’s price does not include, and Seller is not responsible for, payment of any tax levied for sales, use, excise, value-added, goods and services, business (franchise or privilege) or any duties, charges or other such taxes. Seller is only responsible for any tax imposed on Seller, by taxing authorities in Seller’s jurisdiction, which are based on Seller’s revenue, income, net income, net assets, net worth, or capital or any taxes imposed in lieu thereof. Seller accepts sole responsibility and liability for the payment of any and all contributions or taxes for unemployment insurance, social security payments, or other assessments for those persons performing work for Seller hereunder. If Seller is required to pay any taxes or other charges that are the responsibility of the Buyer, then Buyer shall promptly reimburse Seller those amounts.

15. Assignment:

Neither party shall assign an Order or any portion thereof without the advance, written consent of the other party, which consent shall not be unreasonably withheld. The non-assigning party shall not have any obligation to an assignee of the assigning party unless such consent is obtained.

continued

12/0824-3

Pumps




16. Waiver:

Failure by Seller to assert all or any of its rights upon any breach of an Order shall not be deemed a waiver of such rights either with respect to such breach or any subsequent breach, nor shall any waiver be implied from the acceptance of any payment of service. No waiver of any right shall extend to or affect any other right Seller may possess, nor shall such waiver extend to any subsequent similar or dissimilar breach.

17. Severability:

If any portion of these Conditions of Sale is determined to be illegal, invalid, or unenforceable, for any reason, then such provision shall be deemed stricken for purposes of the dispute in question and all other provisions shall remain in full force and effect.

18. Disputes:

Except as otherwise specifically agreed in writing by Buyer and Seller, any dispute relating to an Order placed by a Buyer incorporated in the United States which is not resolved by the parties shall be adjudicated by a court of competent jurisdiction in the state of Texas. For Orders placed by a Buyer incorporated outside the United States, the parties shall resort to binding arbitration under mutually agreed procedures.

19. Applicable Law:

This Agreement shall be interpreted in accordance with the laws of the jurisdiction in which the Seller’s facility accepting the Order hereunder is located, exclusive of any choice of law provisions. The Seller and Buyer expressly agree to exclude from this Agreement the United Nations Convention on Contracts for the International Sale of Goods, 1980, and any successor thereto.

20. Limitation of Liability:

The remedies set forth herein are exclusive, and the total liability of the Seller with respect to this Contract, or any breach thereof, whether based on contract, warranty, tort (including negligence), indemnity, strict liability or otherwise, shall not exceed the Contract Price of the specific equipment or service which gives rise to the claim except in the clause entitled “Patent Indemnity.” IN NO EVENT, WHETHER ARISING BEFORE OR AFTER COMPLETION OF ITS OBLIGATIONS UNDER THE CONTRACT, SHALL SELLER BE LIABLE FOR SPECIAL, CONSEQUENTIAL, INCIDENTAL OR PENAL DAMAGES OF ANY KIND (INCLUDING BUT NOT LIMITED TO LOSS OF USE, REVENUE OR PROFITS, INVENTORY OR USE CHARGES, COST OF CAPITAL, OR CLAIMS OF CUSTOMERS) INCURRED BY BUYER OR ANY THIRD PARTY.

21. Translations; Governing Language:

English shall be the legal language of this Agreement, and all parties waive any right to use and/or rely upon any other language, translation or interpretation. The parties specifically agree that in the case of any inconsistencies or interpretation disputes, the English language version shall control.

22. Entire Agreement:

The contract of purchase, consisting of these terms and conditions, Seller’s quotation and Buyer’s order if accepted in writing by Seller, constitutes the entire agreement between Buyer and Seller. All other previous and collateral agreements (including letters of intent or purchase orders issued by Buyer), representations, warranties, promises and conditions relating to the subject matter hereof are superseded by the contract of purchase. Any understanding, promise, representation, warranty or condition not incorporated in the contract of purchase shall not be binding on either party.

12/0824-4

Pumps





FPD-1210

MEN

END-SUCTION WATER PUM

PS Product Reference Manual

1 Product Summary and

Description

2 Standard and Optional

Construction 3

Pump Features and Benefits 4 Product Brochure

5 Product Presentation 6

Pump Cross Sectional Drawings 7 General Arrangement Drawings 8

Engineering Data

9 Standard Lead Times 10

Typical Specifications 11 Typical Applications 12

Representative Installation Lists

13 Competitive Analysis 14

Coverage Charts 15


16

Drivers, Mechanical Seals and Accessory Information

17 Optional and Alternative

Configurations

18 Aftermarket and Recommended

Spare Parts

19 FAQs (Frequently Asked

Questions) 20

Typical Instruction Manual

21 Submittal Documentation

(Software) 22

Testing Capabilities 23

Pricing for Pumps, Parts and Accessories

24 Terms and Conditions


Description


Construction 3




Engineering Data





Coverage Charts 15


16



Configurations


Spare Parts


Questions) 20



(Software) 22





Description


Construction 3




Engineering Data





Coverage Charts 15


16



Configurations


Spare Parts


Questions) 20



(Software) 22




Designed for Avery 11416 labels

Please Note:

Designed for use with Avery Index Maker® Clear Labels Dividers with White Tabs (Avery part number 11416)

flowserve men end-suction water pumps product …turbofluid.co.za/images/pdf/new/durco - men end...

Documents