flexible packaging roll handling - ht · pdf fileflexible packaging roll handling. dotec....
TRANSCRIPT
1©dotec-RH Im Brochure-3a 2015-11
Dotec R&D - Design & Production Centre 3800 m² / 40.000 ft² FacilityFlex
ible
Pac
kagi
ng R
oll H
andl
ing
Slitter-Rewinder process
From start to finish, film extrusion to end product, rolls need to be handled in various processes.
After rewinding and slitting they need to be taken from the unloading shaft and be palletized.
Further on in the roll life cycle processes like converting, laminating and (label)printing this
again require roll handling solutions. The life of a roll than ends in a final (flexible)packaging/
labeling process to create an attractive end-product for the consumer. Lifting and rotating these
rolls require smart, ergonomic and cost effective solutions. That is our mission at Dotec.
Roll Handling SolutionsManual process
Dotec process
2©dotec-RH Im Brochure-3a 2015-11
The Air-Balancer: The air-balancer is the “muscle” of the system and makes the
elastic vertical movement possible. The compressed air pressure
that move the piston brings the load “in balance”. By letting in
additional compressed air or by escaping air, the piston moves.
The piston rod is connected to a ball-screw that is connected to the
spool. In this way the linear movement of the piston is turned into
a turning movement of the spool. This means that the wire rope
winds up and unwinds. In fact, the load is permanently supported
(in balance) by an air cushion.
The elastic effect is the result of the compressibility of air.
This principle explains the difference between the operation of an
Air-Balancer and a Hoist. The logic control unit permanently
measures the “pressure” in the piston
chamber and uses this information
to react. Once the lifting weight is “In
Balance” only minimal effort (pressure)
is needed to move the load UP & Down.
This all creates the typical
Dotec Dynamics!
Air Balance Lifter®The ABL combines Balance
Lift and horizontal travel
in one unit. Plug & Play
installation. (For 70/150
Kg/Lbs applications)
Housing
Liner
Ball screw
Piston Air
chamber
Spool
Air pressure I N / O U T
Dotec LiftAssists have very specific characteristics that are
based on ease of operation, speed of work and ergonomics in posture.
The learning curve is very short, and work becomes a pleasure.
Dotec The Friendly LiftAssist®.
Dotec ErgoHandle ®The central feature of the Dotec lift assist
is the ergonomic handle, which is used to
operate the lift assist. The handle can move
freely up and down sliding through the
hands, allowing the user to keep his eye on
the load, while a mere finger touch
determines both direction and speed.
There is no need for bending and stretching
(gymnastics) when lifting and storing in high
or low places.
Additional functions are activated by
finger-tip touch of the levers at the sides.
Without distraction or requiring special
attention, likewise the steering wheel of a
car. Not circular but vertical (right-angled),
since we move Up & Down.
Smart logic Controls! (Fully pneumatic)The Dotec LiftAssist guides the process through the following stages:
from empty to full – moving – putting down – from full, back to empty
(Release) (Automated sequence). Extra functions can be added and
operated without using any buttons or switches. This makes operation
foolproof. The logic controls responds automatically (proportional) to
the user’s movements and follows his
own work speed. Compact valve-mod-
ules have been developed to achieve
high speed reaction and avoid (speed)
losses through long pneumatic tubing.
They are in the centre of each logic
control.
Dotec ABC-System:The ABC-System is based on an Air-Balancer
Cylinder instead of the Cable Air-Balancer. It
has the same “Balance” elastic movement. It’s
meant for higher loads up to 250KG.
ZA- Logic Control: Activated by the Ergo-Handle®, the basic
ZA-logic control allows the compressed air to
enter into the Balancer for the up/down-move-
ment. The valves react “proportional”, which
means that “pressing” the operating lever
harder results in a “quicker” up & down move-
ment. This makes operating the lift assist quick
and dynamic, or
quiet and accurate,
whatever way of
operating the pro-
cess requires. This
gives the operator
the feeling that he
(or she) decides
what happens or
should happen,
which creates
positive motivation and an acceleration
of the overall process.
Center of Gravity: (CG)An important feature in every Dotec
system is the automated “Center Of
Gravity” adjustment. This unit secures
the horizontal and vertical alignment
under any condition.
This means that an empty or loaded
handler will always adjust itself into the
correct position. Once adjusted for the
application, it will align automatically.
3©dotec-RH Im Brochure-3a 2015-11
Rotating FamilyRH150xxL R/L50/150Kg
100/300Lb
RH150xxL WR50/150Kg
100/300Lb
The Tilting Family provide fast and efficient roll handling operations for both roll
production and packaging processes (Slitter-Rewinder-Converting-Printing-Packaging
processes). Tell us about your roll handling process and we can advise you what roll
handler fits you best.
The Rotating FamilyPresents ease of operation,
particularly for wider rolls.
It rotates the roll through its
center which enables large/
wide rolls to easily being
picked-up, rotated, and then
placed on the pallet.
The “Balance Mode” control
(option) allow to take rolls
directly from the shaft.
Dotec is more than just a “Roll Handler”. We care about your process.
For over 30 years we’ve studied and observed the roll handling processes
at our customers. We learn and we focus on making these processes more
efficient for you and easier to handle for your operators. We protect the
roll and bring comfort to the job. Speed in combination with comfortable
handling provides “Motivation for the Job” and a positive incentive for the
investment in modern roll handling solutions. Not to mention the money you
can save.
Roll distribution from the warehouse
to the packaging department.
Roll Carts & Trolley’s:
Unloading rolls from a shaft -
- Loading the roll
Roll distribution
Dotec Roll Handling Solutions;
Tilting Family
FP18/32Kg
20/70Lb
FP215/80Kg
30/175Lb
RH9025/100Kg
50/220Lb
RH14050/140Kg
110/300Lb
RH ABC100/250Kg
220/600Lb
RH20060/200Kg
130/450Lb
4©dotec-RH Im Brochure-3a 2015-11
CE Applied Standards:
Machine Directive 2006/42/EG
Cranes - Manually controlled load manipulating devices
NEN-EN 14238:2004+A1 2010
NEN-EN-ISO 12100:2010, NEN-EN-ISO 13857:2008
NEN-EN-ISO 4414: 2010 en
Dotec LiftAssits® are designed and build under strict
CE legislation and therefore provide high and durable
quality connected with safe working conditions for the
operator. Certif ied Manuals are provided. Safety First!
Made in Holland
B: Ceiling Mount Rail System
A: Free standing steel-structure & AL-Railsystem
Accurate and heavy-duty pivot bearing allows smooth and free 360º rotation.
End-stops & Absorbers, can limit the radius. Parking brake (Option) secures a
safe way of parking the Handler, when not in use.
Dotec Infra Structure:The infrastructure is the backbone in the total system. In the design of the LiftAssist, we
strive for maximum weight savings to accomplish minimum effort while moving the load
from A to B. It is therefore most essential that infrastructure components, such as Rail,
Trolley’s and Cranes match these design-rules.
It is designed for a 24/7 production environment at high frequencies.
Our aluminium rail profiles are extruded from 6063-T66 and anodized
for a smooth, clean, corrosive-free surface. The enclosed rail design
reduces the accumulation of dirt and grime on the internal running
surfaces, thus reducing rolling effort. The special rail profiles, the
unique way of suspending and the advanced trolley design provide a
rolling resistance of ≤1% of the load to be moved.
LH- Type Low Headroom Crane
700C Articulating Arm
Air Balance Lifter® (360º)
Jib cranes are perfect for short transfer applications.
Aluminium-rail for the boom provide a comfortable
ergonomic (lightweight) movement.
Parking Brake on hinge
Plug & Play Crane with
integrated Air Balancer.
- 360º rotation
- 1600mm vetical travel
- 2100mm horizontal travel
J-Type Jib Crane
AL-Railsystems Crane Systems
Profile L180
Hangerkit
Profile XL220
A
B