fixtemp c&b 4:1 - dental plus · page 2/8 safety data sheet according to 1907/2006/ec, article 31...

Fixtemp C&B 4:1

Dreve Dentamid GmbH

Max-Planck-Str. 31

59423 Unna / Germany

Tel.: 02303 / 8807-0

Fax: 02303 / 8807-55

[email protected]

www.dreve.com

These data result from measurements which are executed from time to time In view of our quality management system.

This document is valid without any signature.

Rev. 03/ 07.2017 Seite 1 von 1 41-50391/CL

Technical Data Sheet

Product discription: Fixtemp is a resin based material used to fabricate temporary crowns and bridges

Manufacturer: Dreve Dentamid GmbH Max-Planck-Straße 31

59423 Unna / Germany

Composition:

Component A Component B

Chemical term Pos Chemical term

1 Glass powder 1 Urethane dimethacrylate

2 Aerosil 2 Dimethacrylate

3 polyester 3 Glass powder

4 catalyst 4 Aerosil

5 5 pigments

Mixing ratio: 1:4 (Cat:Base)

Contents of syringe: 50 ml

Colours: A1, A2, A3, A3,5,B1, Bleach X, D2

Processing:

Processing time: > 0:45 min

Curing time in the mouth: approx. 2:00 – 3:00 min

Removal of surplus after setting: approx. 6:00 min

Physical properties:

Compressive strenght: (DIN EN ISO 4049:2010) 200 Mpa

Bending resistance: (DIN EN ISO 4049:2010) 60 Mpa

E-Modul: (DIN EN ISO 4049:2010) 1500 Mpa

Water asorption: fulfill the requirements of DIN EN ISO 4049:2010

/8Safety data sheet

according to 1907/2006/EC, Article 31Printing date 31.07.2017 Revision: 31.07.2017Version number 1

45.0

SECTION 1: Identification of the substance/mixture and of the company/undertaking

· 1.1 Product identifier· Trade name: Fixtemp C&B 4:1· 1.2 Relevant identified uses of the substance or mixture and uses advised against

No further relevant information available.· Application of the substance / the mixture Temporary C&B material· 1.3 Details of the supplier of the safety data sheet· Manufacturer/Supplier:

Dreve Dentamid GmbHMax-Planck-Straße 3159423 Unna / GermanyTel.: ++49 2303 /8807-0Fax.: ++49 2303 / 8807-55

· Further information obtainable from:Department Research & DevelopmentFax: ++49 2303 / 8807-562Email: [email protected]

· 1.4 Emergency telephone number:Tel.: ++ 49 211 / 797-3350Plant Fire Department Henkel

SECTION 2: Hazards identification· 2.1 Classification of the substance or mixture· Classification according to Regulation (EC) No 1272/2008

GHS07

Skin Sens. 1 H317 May cause an allergic skin reaction.

· 2.2 Label elements· Labelling according to Regulation (EC) No 1272/2008

The product is classified and labelled according to the CLP regulation.· Hazard pictograms

GHS07

· Signal word Warning· Hazard statements

H317 May cause an allergic skin reaction.· Precautionary statements

P261 Avoid breathing dust/fume/gas/mist/vapours/spray.P272 Contaminated work clothing should not be allowed out of the workplace.P280 Wear protective gloves.P302+P352 IF ON SKIN: Wash with plenty of water.P333+P313 If skin irritation or rash occurs: Get medical advice/attention.P501 Dispose of contents/container in accordance with local/regional/national/international

regulations.(Contd. on page 2)

GB

/8Safety data sheet


Trade name: Fixtemp C&B 4:1

(Contd. of page 1)

45.0

· 2.3 Other hazards· Results of PBT and vPvB assessment· PBT: Not applicable.· vPvB: Not applicable.

SECTION 3: Composition/information on ingredients· 3.1 Chemical characterisation: Substances· CAS No. Description

Not applicable.· Identification number(s) Not applicable.· 3.2 Chemical characterisation: Mixtures· Description: Resin mixture with colouring agents· Dangerous components:

CAS: 41637-38-1EC number: 609-946-4

Ethoxylated (04) Bisphenol A DimethacrylateAquatic Chronic 4, H413

2.5-10%

CAS: 109-16-0 triethylene glycol dimethacrylate Skin Irrit. 2, H315; Eye Irrit. 2, H319; Skin Sens. 1, H317;

STOT SE 3, H335

2.5%

CAS: 72846-00-5EINECS: 276-940-2

1-Benzyl-5-Phenylbarbitursäure Acute Tox. 3, H301

2.5%

· Additional information: For the wording of the listed hazard phrases refer to section 16.

SECTION 4: First aid measures· 4.1 Description of first aid measures· General information: Immediately remove any clothing soiled by the product.· After inhalation:

Supply fresh air and to be sure call for a doctor.In case of unconsciousness place patient stably in side position for transportation.

· After skin contact:Immediately wash with water and soap and rinse thoroughly.If skin irritation continues, consult a doctor.

· After eye contact:Rinse opened eye for several minutes under running water. Then consult a doctor.

· After swallowing:Do not induce vomiting.Call a doctor immediately.

· 4.2 Most important symptoms and effects, both acute and delayedNo further relevant information available.

· 4.3 Indication of any immediate medical attention and special treatment neededNo further relevant information available.

SECTION 5: Firefighting measures· 5.1 Extinguishing media· Suitable extinguishing agents:

CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.· For safety reasons unsuitable extinguishing agents: Water with full jet· 5.2 Special hazards arising from the substance or mixture

No further relevant information available.(Contd. on page 3)

GB

/8Safety data sheet



(Contd. of page 2)

45.0

· 5.3 Advice for firefighters· Protective equipment: Wear self-contained respiratory protective device.

SECTION 6: Accidental release measures· 6.1 Personal precautions, protective equipment and emergency procedures

Avoid contact with skin and eyes.Ensure adequate ventilationWear protective clothing.

· 6.2 Environmental precautions: Do not allow to enter sewers/ surface or ground water.· 6.3 Methods and material for containment and cleaning up:

Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).Dispose contaminated material as waste according to item 13.Ensure adequate ventilation.

· 6.4 Reference to other sectionsSee Section 7 for information on safe handling.See Section 8 for information on personal protection equipment.See Section 13 for disposal information.

SECTION 7: Handling and storage· 7.1 Precautions for safe handling

Avoid contact with skin and eyes.Keep receptacles tightly sealed.Ensure good ventilation/exhaustion at the workplace.Prevent formation of aerosols.

· Information about fire - and explosion protection: No special measures required.· 7.2 Conditions for safe storage, including any incompatibilities· Storage:· Requirements to be met by storerooms and receptacles: Protect against sunlight.· Information about storage in one common storage facility: Store away from foodstuffs.· Further information about storage conditions: Keep container tightly sealed.· 7.3 Specific end use(s) No further relevant information available.

SECTION 8: Exposure controls/personal protection· Additional information about design of technical facilities: No further data; see item 7.· 8.1 Control parameters· Ingredients with limit values that require monitoring at the workplace:

The product does not contain any relevant quantities of materials with critical values that have tobe monitored at the workplace.

· Additional information: The lists valid during the making were used as basis.· 8.2 Exposure controls· Personal protective equipment:· General protective and hygienic measures:

Keep away from foodstuffs, beverages and feed.Immediately remove all soiled and contaminated clothingWash hands before breaks and at the end of work.Avoid contact with the eyes and skin.

(Contd. on page 4) GB

/8Safety data sheet



(Contd. of page 3)

45.0

· Respiratory protection:Do not inhale fumes.In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longerexposure use self-contained respiratory protective device.

· Protection of hands:

Protective gloves

Protective gloves should be changed regularly, especially after intensive contact with the product.For every workplace a suitable type of protective gloves must be selected.The glove material has to be impermeable and resistant to the product/ the substance/ thepreparation.

· Material of glovesNitrile rubber, NBR (0,4 mm)As there are many different conditions in every day work these indications can only serve as an aidto orientation for the selection of suitable gloves for the handling of chemical products. By nomeans they can replace qualifying examinations by the end-user.These recommendations only apply to the product mentioned in the safety data sheet. Whenmixing with other substances or under conditions deviant from norm EN 374 a manufacturer ofCE-approved gloves should be referred to.The selection of the suitable gloves does not only depend on the material, but also on furthermarks of quality and varies from manufacturer to manufacturer. As the product is a preparation ofseveral substances, the resistance of the glove material can not be calculated in advance and hastherefore to be checked prior to the application.

· Penetration time of glove materialThe exact break trough time has to be found out by the manufacturer of the protective gloves andhas to be observed.The determined penetration times according to EN 374 part III are not performed under practicalconditions. Therefore a maximum wearing time, which corresponds to 50% of the penetration time,is recommended.

· Eye protection:

Tightly sealed goggles

· Body protection: Protective work clothing

SECTION 9: Physical and chemical properties· 9.1 Information on basic physical and chemical properties· General Information· Appearance:

Form: PastyColour: Different according to colouring

· Odour: Ester-like· Odour threshold: Not determined.· pH-value: Not determined.· Change in condition

Melting point/freezing point: Undetermined.Initial boiling point and boiling range: >114 °C


/8Safety data sheet



(Contd. of page 4)

45.0

· Flash point: >100 °C· Flammability (solid, gas): Not applicable.· Ignition temperature: >300 °C· Decomposition temperature: > 200 °C· Auto-ignition temperature: Product is not selfigniting.· Explosive properties: Product does not present an explosion hazard.· Explosion limits:

Lower: Not determined.Upper: Not determined.

· Oxidising properties Not determined· Vapour pressure: Not determined.· Density at 20 °C: 1.8 g/cm³· Relative density Not determined.· Vapour density Not determined.· Evaporation rate Not determined.· Solubility in / Miscibility with

water: Not miscible or difficult to mix.· Partition coefficient: n-octanol/water: Not determined.· Viscosity:

Dynamic: Not determined.Kinematic: Not determined.

· Solvent content:Organic solvents: 0.0 %

· 9.2 Other information No further relevant information available.

SECTION 10: Stability and reactivity· 10.1 Reactivity No dangerous reactions if used according to specifications.· 10.2 Chemical stability Stable if used according to specifications.· Thermal decomposition / conditions to be avoided:

Protect from heat and direct sunlight.No decomposition if used according to specifications.

· 10.3 Possibility of hazardous reactionsPhotoreactive.Polymerisation.

· 10.4 Conditions to avoid No further relevant information available.· 10.5 Incompatible materials:

Reacts with peroxides and other radical forming substances.Reacts with reducing agents.Reacts with heavy metals.

· 10.6 Hazardous decomposition products: In case of fire: acrylic, acrid fumes. GB

(Contd. on page 6)

/8Safety data sheet



(Contd. of page 5)

45.0

SECTION 11: Toxicological information· 11.1 Information on toxicological effects· Acute toxicity Based on available data, the classification criteria are not met.· LD/LC50 values relevant for classification: LD50 oral > 5000 mg/kg (rat)· Primary irritant effect:· Skin corrosion/irritation Based on available data, the classification criteria are not met.· Serious eye damage/irritation Based on available data, the classification criteria are not met.· Respiratory or skin sensitisation

May cause an allergic skin reaction.· CMR effects (carcinogenity, mutagenicity and toxicity for reproduction)· Germ cell mutagenicity Based on available data, the classification criteria are not met.· Carcinogenicity Based on available data, the classification criteria are not met.· Reproductive toxicity Based on available data, the classification criteria are not met.· STOT-single exposure Based on available data, the classification criteria are not met.· STOT-repeated exposure Based on available data, the classification criteria are not met.· Aspiration hazard Based on available data, the classification criteria are not met.

SECTION 12: Ecological information· 12.1 Toxicity· Aquatic toxicity: Fish: LC50: > 360 mg/l/48h· 12.2 Persistence and degradability No further relevant information available.· 12.3 Bioaccumulative potential No further relevant information available.· 12.4 Mobility in soil No further relevant information available.· Additional ecological information:· General notes:

Do not allow product to reach ground water, water course or sewage system.Danger to drinking water if even small quantities leak into the ground.

· 12.5 Results of PBT and vPvB assessment· PBT: Not applicable.· vPvB: Not applicable.· 12.6 Other adverse effects No further relevant information available.

SECTION 13: Disposal considerations· 13.1 Waste treatment methods· Recommendation

Must not be disposed together with household garbage. Do not allow product to reach sewagesystem.Disposal must be made according to official regulations.

· Waste disposal key: 180106· Uncleaned packaging:· Recommendation: Disposal must be made according to official regulations.

SECTION 14: Transport information· 14.1 UN-Number· ADR, ADN, IMDG, IATA Void


/8Safety data sheet



(Contd. of page 6)

45.0

· 14.2 UN proper shipping name· ADR, ADN, IMDG, IATA Void· 14.3 Transport hazard class(es)· ADR, ADN, IMDG, IATA· Class Void· 14.4 Packing group· ADR, IMDG, IATA Void· 14.5 Environmental hazards:· Marine pollutant: No· 14.6 Special precautions for user Not applicable.· 14.7 Transport in bulk according to Annex II

of Marpol and the IBC Code Not applicable.· Transport/Additional information: Not dangerous accord ing to the abov e

specifications.

· UN "Model Regulation": Void

SECTION 15: Regulatory information· 15.1 Safety, health and environmental regulations/legislation specific for the substance or

mixture· Directive 2012/18/EU· Named dangerous substances - ANNEX I None of the ingredients is listed.· REGULATION (EC) No 1907/2006 ANNEX XVII Conditions of restriction: 3· National regulations:· Technical instructions (air):· Class Share in % III 2,5-10· 15.2 Chemical safety assessment: A Chemical Safety Assessment has not been carried out.

SECTION 16: Other informationThis information is based on our present knowledge. However, this shall not constitute a guaranteefor any specific product features and shall not establish a legally valid contractual relationship.

· Relevant phrasesH301 Toxic if swallowed.H315 Causes skin irritation.H317 May cause an allergic skin reaction.H319 Causes serious eye irritation.H335 May cause respiratory irritation.H413 May cause long lasting harmful effects to aquatic life.

· Department issuing SDS: Department Research & Development· Contact: Dr. Thomas Veit, Lothar Sutor· Abbreviations and acronyms:

RID: Règlement international concernant le transport des marchandises dangereuses par chemin de fer (Regulations Concerningthe International Transport of Dangerous Goods by Rail)IATA-DGR: Dangerous Goods Regulations by the "International Air Transport Association" (IATA)ICAO: International Civil Aviation Organisation


/8Safety data sheet



(Contd. of page 7)

45.0

ICAO-TI: Technical Instructions by the "International Civil Aviation Organisation" (ICAO)ADR: Accord européen sur le transport des marchandises dangereuses par Route (European Agreement concerning theInternational Carriage of Dangerous Goods by Road)IMDG: International Maritime Code for Dangerous GoodsIATA: International Air Transport AssociationGHS: Globally Harmonised System of Classification and Labelling of ChemicalsEINECS: European Inventory of Existing Commercial Chemical SubstancesELINCS: European List of Notified Chemical SubstancesCAS: Chemical Abstracts Service (division of the American Chemical Society)LC50: Lethal concentration, 50 percentLD50: Lethal dose, 50 percentPBT: Persistent, Bioaccumulative and ToxicvPvB: very Persistent and very BioaccumulativeAcute Tox. 3: Acute toxicity – Category 3Skin Irrit. 2: Skin corrosion/irritation – Category 2Eye Irrit. 2: Serious eye damage/eye irritation – Category 2Skin Sens. 1: Skin sensitisation – Category 1STOT SE 3: Specific target organ toxicity (single exposure) – Category 3Aquatic Chronic 4: Hazardous to the aquatic environment - long-term aquatic hazard – Category 4

GB

Descripción del materialFixtemp C&B es un composite de mezclado automatico, basado en metacrilatos multifuncionales. Sirve para la elaboración de coronas y puentes, inlays, onlays y carillas provisionales. Esta disponible en los colores dentales A1, A2, A3, A3.5, B1 y Bleach X.

IndicaciónCoronas, puentes, inlays, onlays, coronas parciales y carillas provi-sionales y restauraciones provisionales de larga duración.

TiemposLos tiempos de procesado se refieren a una temperatura ambiente de 23 °C y a una humedad relativa del aire del 50 %.

Estos tiempos se prolongan a menor temperatura y se acortan a mayor temperatura.

a) Sistema de elaboración directaFixtemp C&B se dispensa directamente con la cánula de mezcla (especialmente para materiales de 4:1) del cartucho doble en el área de la impresión correspondiente de los dientes a reemplazar. Para obtener resultados exactos y estables se recomienda de recortar el septum interdental en la impresión. Para evitar las burbujas de aire, se debería de mantener la punta de la cánula de mezcla siempre dentro de la masa de material durante la inyección. Las preparaciones tienen que aliviarse así como aislarse ligeramente, por ejemplo con vaselina, en las zonas retentivas. Durante el tiempo indicado de procesado, la impresión rellenada con Fixtemp C&B se

posiciona en su lugar manteniendo una presión constante hasta que se alcance la fase elástica (aproximadamente 2 minutos). Entonces el temporal se puede retirar junto con la impresión. Sin embargo, se debe dejar en la impresión durante al menos 5 minutos (para que finalice la polimerización).b) Elaboración indirectaPara la elaboración del temporal en laboratorio se necesita una impresión de las condiciones antes del tallado de los muñones. Se adapta una plancha termoadaptable (por ejemplo Drufolen H) sobre el modelo. Luego se recorta la llave, contra o patrón de la zona que se va a trabajar. Se rellena con Fixtemp C&B directamente del cartucho a través de la cánula de mezcla. 30 segundos más tarde después del inicio de la mezcla y rellenado de la matriz, se coloca sobre el modelo previamente aislado (por ejemplo con una capa de Isolat film) y se fija a los dientes restantes. Después de dos minutos se alcanza la fase flexible de Fixtemp C&B, la plancha se puede retirar con cuidado junto con el temporal. El provisional debería de permanecer en la matriz hasta el final del curado tras 5 minutos.

Tratamiento• Quitar la capa de inhibición al oxígeno de la superficie de la

restaurcación con ayuda de los disolventes orgánicos tales como el isopropanol.

• Repasar el provisorio después de su endurecimiento completo (después de 5 minutos de comenzalr la mezcla) con fresas de metal duro finas. Si se desea, pulir. No respirar el polvo de esme-rilado, usar una protección de boca o un sistema de aspiración!

• Laquear la superficie con una lace fotopolimerizable (p. ej. Plaquit) o pulir manuelmente con un pulidor de goma o con un cepillo de cabra.

CementarLos cementos con eugenol pueden impedir la polimerización de composites de fijación en la ficación definitiva. Se recomienda utilizar cementos de fijación habituales para fijar el provisional, p. ej. Fixtemp cement.

Características técnicasTiempo de procesamiento > 45 seg.Tiempo de fraguado < 1:50 min.Resistencia a la compresión 200 MPaResistencia a la flexión (Después de 24 h) 60 MPaAbsorción de agua 25 µg / mm³

Avisos importantes• Debido a razones técnicas del llenado, puede haber una presencia

desigual de los dos componentes al comienzo de un cartucho doble nuevo. Por ello no se debe de utilizar el primer material que aparece por la canula de mezcla (aproximadamente el volumen de un guisante).

• Cuando se usa de nuevo un cartucho ya empezado, se debe de retirar posibles tapones antes de usar una nueva cánula de mezcla.

• Se puede desinfectar con todos los actuales productos.• El producto esta exclusivamente diseñado para el campo de

aplicación descrito anteriormente y para usarse por personal cualificado e instruido.

Manténgase fuera del alcance le los niños!Exclusivamente para uso odontológico!

ContraindicacionesEl material no se debe utilzarse en caso de alergia contra una de los ingredientes o alergia de contacto.

Efectos secundariosHasta ahora no se conocen efectos secundarios sistemáticos.

Desinfección del inyector 4:1La desinfección puede llevarse a cabo usando un baño estandar de inmersión. Además se puede esterilizar en autoclave.

Condiciones de almacenamientoA temperatura ambiente, no más de 25 °C.No almazenar en el frigorífico.

Descrizione del materialeIl Fixtemp C&B è un composito automiscelante sulla base di meta-crilati multifunzionali. Serve per la produzione di corone e ponti provvisori, nonchè di inlays ed onlays e veneers ed è disponibile nei colori A1, A2, A3, A3.5, B1 e Bleach X.

Campi di applicazioneCorone e ponti provvisori, inlays, onlays, corone parziali e restauri provvisori di lunga durata.

TempiI tempi di miscelazione e lavorazione ad una temperatura dámbiente di 23 °C ed ad unúmidità relativa dellária del 50 % sono come segue:

Temperature inferiori allungano, temperature più alte riducono i tempi indicati.

a) Metodo diretto Fixtemp C&B viene iniettato direttamente dalla cartuccia doppia e con la cannula di miscelazione (specialmente per materiali 4:1) sulla zona da trattare di unímpronta presa preventivamente dalla preparazione. Per un risultato preciso e stabile si consiglia di tagliare sullímpronta gli spazi interdentali. Al fine di prevenire bolle dária, la cannula deve rimanere sempre immersa nel materiale durante lápplicazione. Sui monconi preparati si debbono eliminare le aree di sottosquadro, e applicare un leggero strato isolante: per entrambi gli scopi si può utilizzare della vasellina. Entro il termine indicato

per la lavorabilità si deve inserire il materiale in situ, mantenendolo con una pressione costante fino alla scadenza del tempo della fase elastica (ca 02:00 min.). Solo ora si può rimuovere il provvisorio insieme allímpronta. Sarebbe meglio, comunque lasciarlo nel cucchiaio per minimo 5 minuti (fino alla fine della polimerizzazione).b) Metodo indirettoPer la produzione di provvisori in laboratorio è necessario avere un modello che riproduca la situazione prima della preparazione e uno con i monconi preparati. Sui denti da preparare si deve provvedere a termostampare un foglio (ad es. Drufolen H) in modo da creare una matrice. Questa opportunamente rifinita va riempita diretta-mente con il Fixtemp C&B tramite la cannula di miscelazione. 30 secondi dopo l'inizio della miscelazione si applica il tutto sui monconi preparati ed adeguatamente isolati (ad es. con Isolat film) e se lo tiene ben fermo in sede. Dopo 2 minuti la fase elastica del Fixtemp C&B viene raggiunta e si può quindi provvedere a togliere il foglio termoformato dolcemente insieme al provvisorio. Si consiglia di lasciare quest´ ultimo all'interno della matrice stessa fino al termine del indurimento, cioè per 5 minuti.

Rifinitura• Il leggero strato di inibizione dell´ ossigeno presente sulla

superfice del provvisorio si può facilmente eliminare nei punti non levigati utilizzando un liquido organico (ad es. Isopropanol).

• Dopo l´ indurimento totale (al più presto 5 minuti dopo l´ inizio della miscelazione) si può rifinire il provvisorio mediante frese in carburo tungsteno. Non respirare la polvere di levigatura, utilizzare protezione per la bocca o aspiratore!

• Lucidare la superficie con una vernice ad elevata lucidità (ad es. con Plaquit) o lucidare manualmente co un gommino o uno spazzolino in pelo di capra.

CementoCementi contenenti eugenolo possono inibire la polimerizzazione di compositi di fissagio nel fissaggio definitivo. Fissare il provvisorio con appositi cementi provvisori di fissaggio presenti sul mercato (ad es. Fixtemp cement).

Dati tecnicitempo di lavorazione > 45 sec. tempo di indurimento < 1:50 min.resistenza alla pressione 200 MParesistenza a rottura (dopo 24 ore) 60 MPaassorbimento idrico 25 µg / mm³

Avvertenze importanti• A causa di motivi tecnici potrebbe accadere che vi sia una distribu-

zione disugale dei due componenti del materiale all` interno delle cartucce. Per questo si consiglia di non utilizzare la primissima quantità di materiale che fuoriesce.

• Quando si usa una cartuccia già iniziata, si consiglia di rimuovere ogni ostacolo dal beccuccio prima di applicare una nuova cannula.

• È possibile provvedere alla disinfezione con tutti i prodotti attual-mente in commercio.

• Il prodotto è stato studiato per gli utilizzi sopra descritti e deve essere utilizzato da personale qualificato ed adeguatamente istruito.

Conservare lontano dalla portata dei bambini!Solo per uso odontoiatrico!

ControindicazioniIl materiale non dovrebbe essere usato in caso di allergie ai componenti o in caso di allergie da contatto.

Effetti collateraliAd oggi non sono stati riscontrati effetti collaterali sistematici.

Disinfezione del dispenser injector 4:1La disinfezione puo' essere fatta in un normale bagno ad immersione oppure in autoclave.

Condizioni di conservazioneA temperatura ambiente, non superiore a 25 °C.Non conservare in frigorifero.

Scadenza: Vedi data di scadenzaNon utilizzare Fixtemp C&B dopo la data di scadenza.

Durabilidad: vease fecha de caducidadNo utilizar Fixtemp C&B si la fecha de caducidad ha expirado.

Medidas de seguridadFixtemp C&B contiene éster de ácido metacrilico. En caso de alergias se recomienda de no utilizar este material.Presentación

D50391 Fixtemp C&B A1 1 x 82 g cartucho doble + 10 cánulas de mezcla


D503925 Fixtemp C&B A2 5 x 82 g cartuchos dobles + 50 cánulas de mezcla


D503935 Fixtemp C&B A3 5 x 82 g cartuchos dobles + 50 cánulas de mezcla

D50394 Fixtemp C&B A3,5 1 x 82 g cartucho doble + 10 cánulas de mezcla

D50395 Fixtemp C&B B1 1 x 82 g cartucho doble + 10 cánulas de mezcla

D50396 Fixtemp C&B Bleach X 1 x 82 g cartucho doble + 10 cánulas de mezcla

Accesorios D4970X4 Cánulas de mezcla 40 piezas D49701X4 Cánulas de mezcla100 piezas D5008 DS 50 Injector 4:1

Misura precauzionaleFixtemp C&B contiene esteri metacrilici acidi. Non usare il materiale in caso di allergia accertata a questi componenti.

Confezioni D50391 Fixtemp C&B A1

1 x 82 g cartuccia doppia incl. 10 cannule di miscelazione

D50392 Fixtemp C&B A2 1 x 82 g cartuccia doppia incl. 10 cannule di miscelazione

D503925 Fixtemp C&B A2 5 x 82 g cartucce doppie incl. 50 cannule di miscelazione

D50393 Fixtemp C&B A3 1 x 82 g cartuccia doppia incl. 10 cannule di miscelazione

D503935 Fixtemp C&B A3 5 x 82 g cartucce doppie incl. 50 cannule di miscelazione

D50394 Fixtemp C&B A3,5 1 x 82 g cartuccia doppia incl. 10 cannule di miscelazione

D50395 Fixtemp C&B B1 1 x 82 g cartuccia doppia incl. 10 cannule di miscelazione

D50396 Fixtemp C&B Bleach X 1 x 82 g cartuccia doppia incl. 10 cannule di miscelazione Accessori

D4970X4 Cannule di miscelazione, 40 pezzi D49701X4 Cannule di miscelazione, 100 pezzi D5008 DS 50 Injector 4:1

Données techniquesTemps de travail > 45 sec. Temps de prise < 1:50 min.Résistance à la pression 200 MPaRésistance à la flexion (après 24 h) 60 MPaAbsorption de l’eau 25 µg / mm³Avis importants• Pour des raisons de production il est possible, qu'au début d'une

nouvelle cartouche il y a une transportation inégale des deux com-posants. Pour cela la première quantité – à peu près la taille d'un petit pois – devrait être jetée.

• En cas d'usage des cartouches déjà commencées il est important que les ouvertures soient nettoyées des blocages éventuelles.

• Une désinfection est possible avec tous matériaux habituels. • Le produit est exclusivement désigné à l'usage indiqué en haut et doit

seulement être procédé par des personnes qualifiées et instruites.

Garder hors de portée des enfants!Seulement pour usage dentaire!

Contre-indicationsLe matériel ne doit pas être utilisé en cas d’ allergies contre undes ingrédients et / ou en cas d’allergies de contact.

Effets secondairesJusqu'à présent, aucun effet secondaire systématique n'est connu.

Désinfection de l'injecteur 4:1La désinfection peut être effectuée avec un désinfectant d'immersion disponible dans le commerceet peut également être autoclavée.

Conditions de stockageA température ambiante, c’est à dire ne pas plus de 25 °C.Ne pas stocker dans le réfrigérateur.

Durabilité: voir date de péremptionNe plus utiliser Fixtemp C&B après la date de péremption.

Mesures de précautionFixtemp C&B contient des esters d’acide méthacryle. En cas d’allergies il est recommandé de ne pas utiliser ce produit.

Conditionnement D50391 Fixtemp C&B A1

1 x 82 g double cartouche + 10 becs mélangeurs

D50392 Fixtemp C&B A2 1 x 82 g double cartouche + 10 becs mélangeurs

D503925 Fixtemp C&B A2 5 x 82 g doubles cartouches + 50 becs mélangeurs

D50393 Fixtemp C&B A3 1 x 82 g double cartouche + 10 becs mélangeurs

D503935 Fixtemp C&B A3 5 x 82 g doubles cartouches + 50 becs mélangeurs

D50394 Fixtemp C&B A3,5 1 x 82 g double cartouche + 10 becs mélangeurs

D50395 Fixtemp C&B B1 1 x 82 g double cartouche + 10 becs mélangeurs

D50396 Fixtemp C&B Bleach X 1 x 82 g double cartouche + 10 becs mélangeurs

Accessoires D4970X4 Becs mélangeurs, 40 pièces D49701X4 Becs mélangeurs, 100 pièces D5008 DS 50 Injector 4:1

Gebrauchsinformation

Working Instructions

Mode d’emploi

Instrucciones de trabajo

Istruzioni d‘uso

Fixtemp C&B4:1

Dreve Dentamid GmbH Max-Planck-Straße 31 · 59423 Unna / GermanyTel +49 2303 88 07-40 · Fax +49 2303 8807-55 [email protected] · www.dreve.com/dentamid

Rx only15°C59°F

Indicaciónes de peligroH317 Puede provocar una reacción alérgica en la piel.Consejos de prudenciaP261 Evitar respirar el polvo/el humo / el gas / la niebla / los vapores / el aerosol. P272 Las prendas de trabajo contaminadas no podrán sacarse del lugar de trabajo. P280 Llevar guantes de protección. P302+P352 EN CASO DE CONTACTO CON LA PIEL: Lavar con abundante agua. P333+P313 En caso de irritación o erupción cutánea: Consultar a un médico.

Eliminar el contenidoP501 Eliminar el contenido o el recipiente conforme a la reglamen-tación local / regional / nacional / internacional.

Indicazioni di pericoloH317 Può provocare una reazione allergica cutanea.Consigli di prudenzaP261 Evitare di respirare la polvere / i fumi / i gas / la nebbia / i vapori / gli aerosol. P272 Gli indumenti da lavoro contaminati non devono essere portati fuori dal luogo di lavoro. P280 Indossare guanti di protezione. P302+P352 IN CASO DI CONTATTO CON LA PELLE: Lavare abbondantemente con acqua. P333+P313 In caso di irritazione o eruzione della pelle: consultare un medico.

Smaltire il prodottoP501 Smaltire il prodotto / recipiente in conformità con le disposi-zioni locali / regionali / nazionali / internazionali.

Ce produit a été développé pour l’usage dans le domaine dentaire et doit être utilisé selon ce mode d’emploi. Pour des dommages dus à un autre usage ou une application inadéquate, le fabriquant décline toute responsabilité. De plus, l’utilisateur est obligé de vérifier ce produit en vue de son aptitude avant l’usage, spécialement, si ces champs d’application ne sont pas mentionnés dans le mode d’emploi.

El producto fue desarollado para uso odontológico y debe ser utilizado según estas instrucciones de trabajo. El fabricante no esta responsable por daños debido a otras aplicaciones o aplicaciones inadecuadas. Además el utilizador esta obligado de examinar el producto antes de utilizarlo en visto a lo apropriado y campo de aplicación planeado – especialmente, si estas objetivos no estan nombrados en las instrucciones de trabajo.

Il prodotto è stato sviluppato per límpiego nel settore dentale e deve essere lavorato secondo le istruzioni dúso. Il produttore non risponde di danni che derivano da un utilizzo diverso o da una lavorazione non corretta. Inoltre lútilizzatore è obbligato a verificare prima dellúso lídoneità e la possibilità di utilizzo per gli scopi previsti, in modo particolare se questi scopi non sono specificati nelle istruzioni d´ uso.

min:seg00:00

min:seg02:00

min:seg03:00

min:seg06:00

min:seg00:45

Inserción en la impresión y reponerla

Fraguado en la boca

Retirada de la boca

Fraguado completo

Tratamiento

min:sec00:00

min:sec02:00

min:sec03:00

min:sec06:00

min:sec00:45

inserimento nellímpronta ed riposizio-

namento

indurimento in bocca

estrazione dalla bocca

indurimento totale

rifinitura

Description of materialFixtemp C&B is an automatically mixable composite on the basis of multifunctional methylacrylates. It is used for the manufacturing of temporary crowns and bridges, as well as inlays, onlays and veneers, and it is available in tooth-colours A1, A2, A3, A3.5, B1 and Bleach X.

IndicationTemporary crowns and bridges, inlays, onlays and veneers and long-term temporaries.

Time dataAt a room temperature of 23 °C and a comparative air humidity of 50 % the following time data is provided for processing:

Lower temperatures extend, higher temperatures shorten the given time data.

a) Direct manufacturingFixtemp C&B is applied directly out of the double cartridge by help of the mixing tips (especially for 4:1 materials) into an impression (which has been taken before the preparation) in the area of the denture. To receive exact and stable results it is recommended to cut out the interdental septum. For the avoidance of air bubbles, it is important that the tip of the mixing tips stays inside the material. The preparations have to be blocked out and insulated at the under-cuts e. g. with Vaseline. The Fixtemp C&B filled impression is to be

inserted in situ within the above mentioned processing time, and is to be hold in position until reaching the flexible phase (approx. 2 min) under constant pressure. Afterwards the temporary can be removed along with the impression, but it is recommended to let it remain inside the impression for about 5 min (end of poly-merisation).b) Indirect manufacturingFor manufacturing the temporary in a dental laboratory a precise situation model of the state before the preparation is required, as well as a prep-model. A thermo-forming blank (e. g. Drufolen H) is placed onto the model in the area of the teeth that need to be prepared; subsequently a matrix is cut out and filled with Fixtemp C&B directly from the double cartridge with the mixing tips. 30 seconds after beginning of mix-ing, the Fixtemp C&B-filled thermo-forming blank is set on the insulated preparation model (e. g. with Isolat Film) and fixed safely at the remaining teeth. After 2 minutes, the flexible phase of Fixtemp C&B is reached, and the thermoforming blank can be removed carefully along with the temporary. Until the material has ultimately hardened after 5 minutes, the temporary is recommended to remain inside the thermoforming blank.

Final Treatment• The inhibition layer on the surface, which has been created by the

aerial oxygen, can be removed from the not-abraded areas with the help of organic solvent (e. g. isopropyl alcohol).

• The temporary is to be treated with fine carbide-trephines after it has hardened completely (at least 5 minutes after begin of mixing). Do not breathe in abrading dust! Use mask or suction!

• Apply light-curing high-gloss lacquer (e. g. Plaquit) or polish manually with rubber-polisher respectively caprine-hair brush.

CementationCements containing Eugenol can interfere the curing composites when fixing. Insert temporary with usual temporary fixing cements (e. g. Fixtemp cement).

Technical dataProcessing time > 45 sec. Curing time < 1:50 min.Pressure strength 200 MPaBending strength (after 24 h) 60 MPaWater absorption 25 µg / mm³

Important advice• Due to technical filling an unbalanced mixing of components

can occur when using new cartridges. For this reason it is recom-mended to dispose the initially mixed pea-sized amount.

• In case of reusing a started double cartridge the outlets have to be cleaned of possible blockages before attaching the mixing tips.

• Disinfection with usual material is possible without any problems.• This product is only to be used in the above mentioned applica-

tion area. Only professional and introduced persons are allowed to use this product.

Keep away from children!Only for dental use!

ContraindicationsThe material should not be used for allergies to any of the ingredients and / or contact allergies.

Side effectsSo far no systematic side effects are known.

Desinfection of the Injector 4:1The disinfection can be carried out with a common immersion disinfection and is also autoclavable.

Storage conditionsStore at room temperature that means not over 25 °C. Do not store in refrigerator!

Description du matériauFixtemp C&B est un composite de mélange automatique à la base de méthacrylates multi-fonctionnels pour la production de couronnes et bridges provisoires ainsi que pour des inlays, des onlays et des facettes. Fixtemp C&B est disponible en couleurs dentaires A1, A2,A3, A3.5, B1 et Bleach X.

IndicationCouronnes et bridges provisoires, des inlays, des onlays, des couronnes partielles des facettes et des provisoires de longue durée.

TempsLes temps de travail se réfèrent à une température ambiante de 23 °C et une humidité d’air relative de 50 %.

Des températures inférieures prolongent et des tempéra tures plus hautes ralentissent ces temps.

a) Production directeAppliquer Fixtemp C&B directement de la double cartouche par le bec mélangeur (spécial pour des matériaux 4:1) dans la partie du dentier de l'empreinte de situation, qui a été prise avant de la préparation. Pour des résultats exacts et stables il est recommandé de couper le septum interdentaire de l'empreinte. Pour éviter les bulles d'air, il faut observer que la pointe du bec mélangeur reste dans le matériau durant l'injection. Les préparations doivent être bloqués et isolés dans les cavités, p. ex. avec de la vaseline. Dans le temps de travail indiqué en haut l'empreinte remplie avec Fixtemp C&B doit être mise en situ

Erreichung der flexiblen Phase (ca. 2 Min.) in der Position gehalten werden. Anschließend kann das Provisorium zusammen mit der Abformung entformt werden, sollte aber bis zum Ablauf von mindestens 5 Min. (Abschluss der Polymerisation) in der Abformung verbleiben.b) Indirekte HerstellungFür die Herstellung eines Provisoriums im zahntechnischen Labor wird ein möglichst präzises Situationsmodell vom Zustand vor der Präparation sowie ein Stumpfmodell benötigt. Über das Situationsmodell wird im Bereich der zu präparierenden Zähne eine Tiefziehfolie (z. B. Drufolen H) gezogen, anschließend eine Schablone herausgeschnitten und mit Fixtemp C&B direkt aus der Doppelkartusche mit aufgesetzter Mischkanüle gefüllt.30 Sekunden nach Mischbeginn wird die mit Fixtemp C&B gefüllte Tiefziehfolie auf das isolierte Präparationsmodell (z. B. mit Isolat Film) gesetzt und anhand des Restzahngebisses sicher fixiert. Nach Ablauf von weiteren 2 Min. wird die flexible Phase von Fixtemp C&B erreicht, die Tiefziehfolie kann zusammen mit dem Provisorium vorsichtig entfernt werden. Bis zur endgültigen Aushärtung des Materials nach 5 Min. sollte das Provisorium in der Tiefziehfolie verbleiben.

Ausarbeitung• Die durch Luftsauerstoff entstandene oberflächliche Inhibitions-

schicht kann an den Stellen, an denen nicht beschliffen wurde, mit organischen Lösungsmitteln, z. B. Isopropanol, entfernt werden.

• Das Provisorium nach vollständiger Aushärtung (frühestens 5 Min. nach Mischbeginn) mit feinen Hartmetallfräsen ausarbeiten. Schleifstaub nicht einatmen, Mundschutz oder Absaugung verwenden!

• Oberfläche mit einem lichthärtenden Hochglanzlack (z. B. Plaquit) lackieren oder mit einem Gummipolierer bzw. Ziegenhaar-bürstchen manuell polieren.

ZementierungEugenolhaltige Zemente können die Abbindung von Befestigungs-kompositen bei der definitiven Befestigung behindern!Das Provisorium mit handelsüblichen provisorischen Befestigungs-zementen, z. B. Fixtemp cement einsetzen.

Technische DatenVerarbeitungszeit > 45 Sek. Abbindezeit < 1:50 Min.Druckfestigkeit 200 MPaBiegefestigkeit (nach 24 h) 60 MPaWasseraufnahme 25 µg / mm³Wichtige Hinweise• Aus abfülltechnischen Gründen kann bei Neukartuschen zuerst

eine ungleichmäßige Förderung der Komponenten auftreten. Aus diesem Grunde sollte die erstgeförderte, etwa erbsengroße Menge verworfen werden.

• Bei Wiederverwendung von angebrochenen Doppelkartuschen müssen vor dem Aufsetzen der Mischkanüle die Material-austrittsöffnungen von evtl. Verstopfungen befreit werden.

• Eine Desinfektion ist mit allen handelsüblichen Materialien prob-lemlos möglich.

• Das Produkt ist ausschließlich für den o. g. Einsatzbereich bestimmt und nur von fachlich qualifizierten und eingewiesenen Personen zu verwenden.

Für Kinder unzugänglich aufbewahren!Nur für den zahnärztlichen Gebrauch verwenden!

KontraindikationenDas Material sollte nicht eingesetzt werden bei Allergien gegen einen der Inhaltsstoffe und / oder bei Kontaktallergien.

NebenwirkungenBisher sind keine systematischen Nebenwirkungen bekannt.

Desinfektion des Injektor 4:1Die Desinfektion kann mit einer handelsüblichen Tauchdesinfektion erfolgen, außerdem ist er autoklavierbar.

Lagerungsbedingungenbei Raumtemperatur, d. h. nicht über 25 °C lagern. Nicht im Kühlschrank lagern.

au patient et gardée dans cette position en pression constante jusqu'à l'obtention de la phase flexible (approx. 3 min.). Après le provisoire peut être enlevé avec l'empreinte; il doit rester dans l'empreinte pour 5 min. au minimum (terminaison de la polymérisation).b) Production indirectePour la production d'un provisoire dans le laboratoire dentaire il faut un modèle de situation précise en état avant la préparation ainsi qu'un modèle de moignon. Dans l'endroit des dents à préparer il faut appli-quer une feuille de thermoformage (p. ex. Drufolen H) sur le modèle de situation, et puis couper un gabarit et remplir avec Fixtemp C&B de la double cartouche avec un bec mélangeur. 30 secondes après le mélange la feuille de thermoformage avec Fixtemp C&B sera appli-quée sur le modèle de préparation isolé (p. ex. avec Isolat film) et fixée à l'aide des dents restants. Après 2 minutes ultérieures la phase flexible de Fixtemp C&B sera atteinte, on peut enlever la feuille de thermoformage ensemble avec le provisoire. Le provisoire devrait rester dans la feuille de thermoformage jusqu'au durcissement complet du matériau, c'est à dire environ 5 min.

Traitement• La couche d’inhibition, qui s’avait formé à la surface à cause d’oxygène

dans l’air, peut être enlevé aux endroits non-meulés avec des solvants organiques, p. ex. isopropanole.

• Traiter le provisoire après durcissement complet (au plus tôt 5 min. après mélange) avec des fraises au métal dur fines. Ne pas aspirer la poussière de meulage, utiliser une masque de protection ou un aspirateur !

• Laquer la surface avec un vernis photopolymérisant (p.e. Plaquit) ou polir manuellement avec un polissoir en gomme ou une brosse en chèvre.

CimenterDes ciments contenant d’eugénol peuvent perturber la prise de com-posites de fixation durant la fixation définitive! Pour cela insérer le provisoire avec des ciments de fixation provisoires courants, p. ex. Fixtemp cement.

Drev

e De

sign

Rev.1

2061

8-DU

1206

18-1

000-

3014Haltbarkeit: siehe Ablaufdatum.

Fixtemp C&B nach Ablauf des Verfallsdatums nicht mehr verwenden.

VorsichtsmaßnahmenFixtemp C&B enthält Methacrylsäureester. Bei bekannter Allergie gegen diese Bestandteile ist auf eine Anwendung zu verzichten. Lieferform

D50391 Fixtemp C&B A1 1 x 82 g Doppelkartusche inkl. 10 Mischkanülen


D503925 Fixtemp C&B A2 5 x 82 g Doppelkartuschen inkl. 50 Mischkanülen


D503935 Fixtemp C&B A3 5 x 82 g Doppelkartuschen inkl. 50 Mischkanülen

D50394 Fixtemp C&B A3,5 1 x 82 g Doppelkartusche inkl. 10 Mischkanülen

D50395 Fixtemp C&B B1 1 x 82 g Doppelkartusche inkl. 10 Mischkanülen

D50396 Fixtemp C&B Bleach X 1 x 82 g Doppelkartusche inkl. 10 Mischkanülen

Zubehör D4970X4 Mischkanülen 40 Stück D49701X4 Mischkanülen 100 Stück D5008 DS 50 Injector 4:1

Durability: see date of expiryFixtemp C&B is not to be used when expiry date has passed.

CautionFixtemp C&B contains methacryl acid ester. In case that allergic reactions according to this component are known, do not use!

Mode of delivery D50391 Fixtemp C&B A1

1 x 82 g double cartridge incl. 10 mixing tips

D50392 Fixtemp C&B A2 1 x 82 g double cartridge incl. 10 mixing tips

D503925 Fixtemp C&B A2 5 x 82 g double cartridges incl. 50 mixing tips

D50393 Fixtemp C&B A3 1 x 82 g double cartridge incl. 10 mixing tips

D503935 Fixtemp C&B A3 5 x 82 g double cartridges incl. 50 mixing tips

D50394 Fixtemp C&B A3.5 1 x 82 g double cartridge incl. 10 mixing tips

D50395 Fixtemp C&B B1 1 x 82 g double cartridge incl. 10 mixing tips

D50396 Fixtemp C&B Bleach X 1 x 82 g double cartridge incl. 10 mixing tips

Accessories D4970X4 Mixing tips 40 pieces D49701X4 Mixing tips 100 pieces D5008 DS 50 Injector 4:1

MaterialbeschreibungFixtemp C&B ist ein automatisch anmischbares Komposit auf der Basis von multifunktionellen Methacrylaten. Es dient der Herstellung von provisorischen Kronen und Brücken sowie Inlays, Onlays und Veneers und ist erhältlich in den Zahnfarben A1, A2, A3, A3.5, B1 und Bleach X.

IndikationProvisorische Kronen, Brücken, Inlays, Onlays, Teilkronen, Veneers und Langzeitprovisorien.

ZeitenBei 23 °C Raumtemperatur und einer relativen Luftfeuchtigkeit von 50 % stehen für die Verarbeitung folgende Zeiten zur Verfügung:

Geringere Temperaturen verlängern, höhere Temperaturen verkürzen die angegebenen Zeiten.

a) Direkte Herstellung Fixtemp C&B wird direkt aus der Doppelkartusche durch die aufgesetzte Mischkanüle (speziell für 4:1 Materialien) in eine Situationsabformung, welche vor der Präparation genommen wurde, in den Bereich des Zahnersatzes appliziert. Für exakte und stabile Ergebnisse emp-fiehlt es sich, die Interdentalsepten aus der Abformung herauszu-schneiden. Zur Vermeidung von Luftblasen sollte darauf geachtet werden, daß die Spitze der Mischkanüle während der Förderung immer innerhalb des Materials verbleibt. Die Präparationen müssen an unter sich gehenden Stellen ausgeblockt sowie leicht isoliert werden, z. B. mit Vaseline. Innerhalb der oben angegebenen Verarbeitungszeit muss die mit Fixtemp C&B gefüllte Abformung beim Patienten wieder in situ gebracht und mit möglichst gleichbleibendem Druck bis zur

AchtungWarningAttentionAtenciónAttenzione

GefahrenhinweiseH317 Kann allergische Hautreaktionen verursachen.SicherheitshinweiseP261 Einatmen von Staub / Rauch / Gas / Nebel / Dampf / Aerosol vermeiden.P272 Kontaminierte Arbeitskleidung nicht außerhalb des Arbeitsplatzes tragen. P280 Schutzhandschuhe tragen. P302+P352 BEI BERÜHRUNG MIT DER HAUT: Mit viel Wasser waschen. P333+P313 Bei Hautreizung oder -ausschlag: Ärztlichen Rat einholen / ärztliche Hilfe hinzuziehen.

EntsorgungP501 Entsorgung des Inhalts / des Behälters gemäß den örtlichen / regionalen / nationalen / internationalen Vorschriften.

Hazard statementsH317 May cause an allergic skin reaction.Precautionary statementsP261 Avoid breathing dust / fume / gas / mist / vapours / spray. P272 Contaminated work clothing should not be allowed out of the workplace. P280 Wear protective gloves. P302+P352 IF ON SKIN: Wash with plenty of water. P333+P313 If skin irritation or rash occurs: Get medical advice / attention.

DisposalP501 Dispose of contents / container in accordance with local / regional / national / international regulations.

Mentions de dangerH317 Peut provoquer une allergie cutanée.Conseils de prudenceP261 Éviter de respirer les poussières / fumées / gaz / brouil-lards / vapeurs / aérosols. P272 Les vêtements de travail contaminés ne devraient pas sortir du lieu de travail. P280 Porter des gants de protection. P302+P352 EN CAS DE CONTACT AVEC LA PEAU: Laver abondamment à l’eau.P333+P313 En cas d'irritation ou d'éruption cutanée: consulter un médecin.

Éliminer P501 Éliminer le contenu / récipient conformément à la réglementation locale / régionale / nationale / internationale.

Stand der Information, Date of information, L‘etat actuel de I‘information, Información actualizada, Data delle informazioni: 06.2018

Das Produkt wurde für den Einsatz im Dentalbereich entwickelt und muss gemäß Gebrauchsinformation angewendet werden. Für Schäden, die sich aus anderweitiger Verwendung oder nicht sachgemäßer Anwendung ergeben, übernimmt der Hersteller keine Haftung. Darüber hinaus ist der Verwender verpflichtet, das Produkt eigenverantwortlich vor dessen Einsatz auf Eignung und Verwendungsmöglichkeit für die vorgesehenen Zwecke zu prüfen, besonders wenn diese Zwecke nicht in der Gebrauchsinformation stehen.

This product was developed for dental use and has to be used according to the instructions. In the case of damages resulting from ulterior or improper use, the manufacturer assumes no liability. Furthermore the user is bound to check the product according to suitability and possible use in self dependence before using it subject to its purpose, especially in case the purpose is not mentioned in the instructions.

min:sek00:00

min:sek02:00

min:sek03:00

min:sek06:00

min:sek00:45

Einbringenin den

Abdruck undReponierung

Abbindenim Mund

Entnahmeaus dem

Mund

Vollständige Abbindung

Bearbeitung

min:sec00:00

min:sec02:00

min:sec03:00

min:sec06:00

min:sec00:45

Insertinginto the

impressionand re-

positioning

Curing insidethe mouth

Removalfrom

the mouth

Completebinding

Processing

min:sec00:00

min:sec02:00

min:sec03:00

min:sec06:00

min:sec00:45

Injection dans

l’empreinte et repositi-

onnement

Temps de prise dans la

bouche

Enlèvement de la bouche

Prise complète

Traitement

fixtemp c&b 4:1 - dental plus · page 2/8 safety data sheet according to 1907/2006/ec, article 31...

Documents