fittings section v: illustrated fitting locater...

© 2014 Truckers AC 398

MALE FEMALE

Fittings Section V: Illustrated

FITTING LOCATER GUIDE

bASIC hOSE FITTING TypES

Fitting sizes are identified generally as: 6, 8, 10, 12, 14 and 16. These numbers come from 6/16”, 8/16”, 10/16”, and 12/16” which generally identify the tube diameter at the point that it passes through the attached threaded nut. An illustration of this measurement and a chart of sizes is shown below:

Fitting Sizes

TYPE OF FITTING ....................................................................PAGEPAD MANIFOLD ...........................................................................431QUICK DISCONNECT ..........................................................403, 417REDUCED DIAMETER .................................................................404REPAIR FITTINGS (Weld-On) .....................................................421RETROFIT PORTS .......................................................................434SERVICE VALVES .......................................................................435SHRADER PORTS / ADAPTERS .................................................434SPLICERS (Beadlock) .................................................................422SPECIALTY Adapters / Manifolds ..............................................442SUCTION TEE, TEE BLOCKS .....................................................440TUBE and LINE Repair Kits ........................................................404WELD-ON, SOLDER-ON ......................................................421, 434

TYPE OF FITTING ....................................................................PAGEADAPTERS ...................................................................402, 403, 442AEROQUIP E-Z CLIP ..................................................................406BEADLOCK (Reduced Diameter) ...............................................404BEADLOCK (Standard) ..............................................................414BURGA-CLIP ................................................................................411BULKHEAD ..................................................................................403EVAPORATOR REPAIR ...............................................................405FIELD REPAIR and HARDLINE ..................................................424FRIGOCLIC© / MANULI (Refri*MasterPlus) ......................426, 431HEATER FITTINGS ......................................................................484CCOT - ORIFICE TUBE ASSEMBLIES .......................................405

FITTING SIZES

TUBE O.D. FITTING SIZE THREAD SIZE

1/4” 4 7/16” 3/8” 5 9/16” 3/8” 6 5/8” 3/8” 7 11/16” 1/2” 8 3/4” 5/8” 10 7/8” 3/4” 12 1-1/16” 1” 14 n/a 1-15/64” 16 n/a

Note: Metric connections are not included in this sizing method.

Tube O.D.

FlAre FiTTiNgsThe sAe 45° flare fitting is found on older cars and trucks, many european made cars, recreational vehicles, construction and agricultural equipment using r12. The flare fitting seals with metal to metal contact and requires higher torque than o-ring style fittings. Not recommended for use with r134a.

O-riNg FiTTiNgsThe concept of the o-ring fitting achieves an effective seal in automotive air conditioning systyems through the use of an o-ring placed in a specially designed groove or cavity intended to apply a mild compression on the o-ring. The threads of the o-ring fittings serve only as a mechanical connection and require substantially less torque values than the comparable flare design. This design has proven more reliable than the flare fitting design, and is widely accepted as an international standard for mobile air conditioning systems. Care should be taken to use only HNbr, HsN, or Neoprene rubber compounds (as opposed to the old Nbr or nitrile materials) in repair applications which involve the new r134a refrigerant and compatible lubricants.

spriNg lOCk FiTTiNgsThis is a dual o-ring style OeM style connection used and patented by Ford Motor Company. The dual o-rings seal in a precision “barrel” and are held together mechanically by the use of a tube flare behind a garter spring. This design requires no tools to assemble, but does require special tools to disassemble. Also, special care must be taken by the repair technician to insure that the “flare-to-garter spring” connection is fully engaged.

gAskeT and seAliNg wAsHer FiTTiNgsThere are many types of variation on the gasket seal concept which have been used by OeM’s in the last 30 years. All rely on fairly heavy compression of the sealing material to metal surfaces for sealing. some examples are listed below:

• pad – These are generally “manifold” style connections often seal inlet and outlet fittings with the same gasket. They are generally secured through the use of a “hold-down” bolt.

• Teflon™ – This is a seal based on a Teflon™ ring being compressed into a groove and is known as a rotolock fitting. These fittings always use a 1”–14 thread torque to produce the compression.

• O-ring – There are many A/C systems worldwide which use this “o-ring-in-a-groove” or “over the tube” design.

rubberO-ring

TeflonO-ring

MAle MAle iNserT FeMAle

FEMALE

MANiFOlD (pAD)

sAe FlAre

O'riNg

spriNglOCk


Tube O.D. HOse i.D.

Aeroquip gH134 eZ Clip Hose eZ Clip only 15-3242 pliers (size 6-12), 15-3247 (#16)ATCO 3700 Two braid dimension, nylon barrier beadlock ATCO 15-3200A or 15-3256 burgaclip 3090 reduced barrier burgaclip, beadlock reduced 15-3243bC; 15-3200A or 15-3256Dayco 3103, 3054 single braid, reduced O.D. braid beadlock reduced, burgaclip ATCO 15-3200A *2, or 15-3256Dayco 3305 Two braid, nylon barrier beadlock ATCO 15-3200A or 15-3256Dayco T2 Two braid, all rubber beadlock ATCO 15-3200A or 15-3256goodyear 4816, Two braid dimension, beadlock 15-3242 pliers (size 6-12)4824, 4826 nylon barrier ATCO 15-3200A or 15-3256goodyear 4850, 4860 single braid, reduced O.D. barrier beadlock reduced, burgaclip ATCO 15-3200A *2, or 15-3256Manuli Type e, Class 1 High temp. braided synthetic rubber Manuli “Quick Click” only 15-3242 pliersparker 7634, 7637 reduced O.D. beadlock reduced, burgaclip ATCO 15-3200A or 15-3256parker bHk barrier Hose std. size beadlock ATCO 15-3200A or 15-3256

Section V: Illustrated Fittings

FITTING RECOmmENDATIONShose Type hose Description Recommended Fittings Recommended Crimper

hOSE SIzES and TypES

RECOmmENDED CRImp for hOSE COUpLINGS (clip types not shown)

A/C Hose size is determined by the inside and outside diameter of the hose. Outside diameters of hoses vary significantly and MusT NOT be used solely to determine hose size. All “beadlock-style” fittings shown in this catalog (i.e. parts with “b” or “bs” suffixes) are designed to be coupled to barrier two braid dimension hose ONlY1. Hose sizes also are known by the “6, 8, 10, 12, 14, and 16” number designations. The chart below shows hose i.D.’s and their corresponding size number.

It is very important that a proper combination of hose, fitting and crimp style be used to insure a coupling of high integrity. sAe J2064 Coupling integrity standards require that extensive testing be done on crimped hose assemblies to insure “leak-free” couplings that will be environmentally friendly. Testing has shown that the old barb fitting design when coupled with wormgear clamps or even ferrules and “face crimped” will not pass these new coupling integrity performance requirements. The only fitting and crimp designs which have been found to meet these sAe requirements are the “beadlock-style” fitting with a “bubble-style” crimp. both are illustrated below, along with a chart showing important details of the ATCO beadlock fitting design:

To determine the hose size that a specific fitting is designed to fit, measure the outside diameter of the hose insert as shown above.

Note: 1 reduced dia. barrier hose (goodyear #4850, 4860/Dayco #3054, 3103) supplied in single braid only. see following section “reCOMMeNDeD CriMp FOr HOse COupliNg” for additional info.

STANDARD BEADlOck FITTING DETAIl

REDUcED O.D. BEADlOckFITTING DETAIl BUBBlE STYlE cRIMP

standard size hose and reduced diameter hose have different diameters.

0.290 6 0.385 8 0.480 10 0.600 12 0.745 14

REDUcED HOSE SIZES

std.illust. A (i.D.) 0.780” 0.940” 1.040” 1.165”

reduced illust. b (i.D.) 0.590 0.7187 0 .7812 .950

Hose size #6 #8 #10 #12

A B

Note:*1 Adjustable crimpers: weatherhead coll-o-crimp, Dayco Np 30 Or Np 60, gates pC707.*2 Fittings and crimp dies for reduced O.D. nylon barrier hose such as goodyear 4850 & 4860 or Dayco 3103 & 3054 are available for use with the #15-3200A crimper.

5/16” 6 13/32” 8 1/2” 10 5/8” 12 7/8” 16

STD. HOSE SIZES HOSE I.D. HOSE SIZE


08-6962BS

DeNOTes HOse siZe1 = No. 6 (5/16”) (std or reduced)2 = No. 8 (13/32”) (std or reduced)3 = No. 10 (1/2”) (std or reduced)4 = No. 12 (5/8”) (std or reduced)5-9 = step sizeNote: Does not apply to fittings with third digit of 7, 8, or 9


SERVICE pORT INFORmATIONThere are a number of fittings that include an integral service port (for attaching manifold charging hoses), either for r12 or r134a (see illust. A). in addition, some fittings may include a switch port, used for the purpose of attaching a pressure switch to the system. The standard size switch ports used are 1/4” (actually 7/16” - 20 thread), 3/16” (actually3/8” - 24 thread), and metric M10 and M12 sizes normally associated with r134a systems.

ILLUSTRATION A

r12 serViCe pOrT/r134a swiTCH pOrT r134a lOw siDe 13MM pOrT 1 r134a HigH siDe 16MM pOrT 1

Note:1 r134a service ports may be supplied in either standard flow, or High Flow (eaton ssV) type. both are interchangable, except for the replacement shrader core inside the port. The High Flow shrader core requires a special remover/installer (p/N 16-3434), and is the preferred style (if available), providing faster charging/evacuation periods.

TRUCk AIR NUmbERING SySTEm FOR hOSE FITTINGS (pART NUmbER FORmAT)NOTE: UNLESS NOTED, ALL FITTINGS SUppLIED WITh NECESSARy O-RINGS, CLAmpS, ETC.

NOTe: To be used as a general guide, and applies ONlY to Hose Fittings and MAY NOT apply to adapters, compressor and compression fittings, splicers, dual o-ring or metric fittings, spring lock fittings, service valves, or tee connectors. The format is approximately 99% accurate.

FF - Female Flare MF - Male Flare FOr - Female O-ring MiO - Male insert O-ring FiO - Female insert O-ring

MOr - Male O-ring Fsl - Female spring lock Ms - Male spring lock FTO - Female Tube-O MTO - Male Tube-O

Frl - Female rotolock Mrl - Male rotolock DsOr - Dual standard O-ring DMOr - Dual Metric O-ring sl - springlock

USEFUL STANDARD AbbREVIATIONS FOR FITTINGS GUIDE

eX.prefixDeNOTes All FiTTiNg pArT NuMbers

First DigitDeNOTes FiTTiNg TYpe4 = Female Flare5 = Male O-ring6 = Female O-ring7 = springlock8 = special Type

second DigitDeNOTes ANgle0 = straight4 = 45 Degree9 = 90 Degree

suffix

b = beadlock (std. Dia.)bC = burgaclip bD = beadlock (short Drop)br = beadlock (reduced Dia.)bs = beadlock (steel) (std. Dia.)-10 = 10 per box(bulk) e = eZ Clip s = steel Q = Manuli / Frigoclic

Third Digit

DeNOTes sTANDArD Or speCiAl TYpe0 = Aeroquip Type Male fitting 1 = Aeroquip Type Female fitting2 = special Threads(gMC/iHC 11/16” - 16)3 = r134a Male/Female O-ring w/port4 = r134a Male insert O-ring w/port5 = Male insert O-ring fitting6 = standard (non-step) fitting7 = step up/step down fitting8 = standard fitting w/port9 = step fitting w/port

Fourth Digit



ThREADED FITTING SIzE ChART - ALL FITTINGS ACTUAL SIzE (#14, #16 not shown)

sAe FeMAle FlAre (no o-ring used)

No. 121-1/16” - 14 Thread

No. 107/8” - 14 Thread

No. 83/4” - 16 Thread

No. 65/8” - 18 Thread

MAle iNserT O-riNg (o-ring located on inside)

No. 121-1/16” - 14 Thread

No. 107/8” - 14 Thread

No. 83/4” - 16 Thread

No. 65/8” - 18 Thread

MAle O-riNg (o-ring located on outside)

No. 121-1/16” - 16 Thread

No. 107/8” - 18 Thread

No. 83/4” - 18 Thread

No. 7speCiAl gM/iHCDrier FiTTiNg

11/16” - 16 Threads

No. 65/8” - 18 Thread

FeMAle O-riNg (o-ring located on outside)

No. 121-1/16” - 14 Thread

No. 107/8” - 14 Thread

No. 83/4” - 16 Thread

No. 65/8” - 18 Thread


8-8 (Discharge) ........08-8038 1,3 10-10 (suction) ............08-8040 2,4

FlAre TO O-riNg ADApTersConverts Male Flare to Male insert O-ring 6 ..............................08-8006 8 ..............................08-8008 10 .............................08-8010

FeMAle O-riNg X MAle iNserT O-riNgr134a serViCe pOrT ADApTers

r134a

ideal for adding r134a service ports to #8 and #10 Male insert O-ring Fittings

1) 16 mm port2) 13 mm port3) for 90° use 08-34894) for 90° use 08-3490

2-1/2” length

sHrADer pOrT ADApTer / reCeiVer Drier 1/8” pipe x 1/4” r12 .................................................................................08-80563/8”-24uNF2A X 1/4” std. r12 port ........................................................08-8057Converts female switch port to male port on filter driers.

rOTOlOCk TO Tube-O ADApTer ......................................08-3070Converts rotolock style York and Tecumseh comp. to Tube-O style. supplied 1 per box. (2 required)

FlAre ADApTers 90 °Female Flare to Female Flare Adapter 8x8 ...................... 08-3962FF

FlAre ADApTers 90 °Flare to Female O-ring Adapter 8x8 ......................08-3962FO

DESCRIpTION FTG. SIzE pART NO. DESCRIpTION FTG. SIzE pART NO.


ADApTER FITTINGS (also see REtRoFIt PoRt ADAPtERs, page 434)

Tube-O TO rOTOlOCk ADApTers ........................................08-3076Converts Tube-O style York and Tecumseh comp. to rotolock style(2 per box)

MAle swiTCH pOrT ADApTer FiTTiNgMAle X MAle MeTriCM10-1.25 x 3/8-24 switch port ................................................................08-8058

M E T R I CMAle swiTCH pOrT ADApTer FiTTiNgMAle X MAle MeTriCM12-1.5 x 3/8-24 switch port ................................................................. 08-8059

M E T R I C

iNliNe CHArge FiTTiNgw/r12 port 6 ...........................08-8036A3/8” Male O-ring x 3/8” Female O-ring

r12

Drier ADApTer3/8” Male O-ring to 3/8” MiO ............................. 6 ....................................08-806011/16” Male O-ring to 3/8” MiO ......................... 6 ....................................08-8061

CHArge pOrT ADApTer3/8”-24 to 16mm (high side) ............................. 6 ....................................08-8064

r134a

r12

MAle iNserT O-riNg TO MAle 6 ..............................08-3009FlAre ADApTers 8 ..............................08-3069Converts O-ring to Flare 10 .............................08-3099(2 per box)

uses HNbr#16-4210

uses HNbr#16-4210

uses teflon#16-4018

uses teflon#16-4018

(requires o-ring)


bULkhEAD FITTINGS Also see E-Z ClIP stylE, BulkhEAD FIttIngs, page 407.

bLOCk-OFF pLUGS see page 405.

MAle X MAle wiTH NuTsFor routing hose through firewall/cab/roof 6x6 ............................08-8066 8x8 ............................08-8068 10x10 ..........................08-8070 12x12 ..........................08-8072

FTG. STEELDESCRIpTION SIzE pART NO.

MAle iNserT O-riNg 6x6 ......................08-8076BS 8x8 ......................08-8078BS 10x10 ....................08-8080BS

FTG. DESCRIpTION SIzE pART NO.

MAle iNserT O-riNg 90° 6x6 ......................08-8976BS 8x8 ......................08-8978BS 10x10 ....................08-8980BS 14x12 ................... 08-8984BR 1

QuiCk DisCONNeCTMAle iNserT O-riNg #10 MiO ........................08-80206-11/16” length1-1/2” dia. mounting hole requiredreplaces Oe CAT 5p3929

welD-ON swiTCH pOrT FiTTiNgM10 x 1.25 switch port (steel) .............................................................08-8310S

M E T R I C


DESCRIpTION FTG. SIzE pART NO. DESCRIpTION FTG. SIzE pART NO.

ADApTER FITTINGS (continued)

Drier ADApTer 7/16” Female Flare to M10 Male switch port Adapter .............................08-8067

Drier ADApTer M10 Female Flare to 7/16” r12 Male Flare Adapter ...............................08-8069

r12

CHArge pOrT ADApTer3/8”-24 to 13mm (low side) ............................... #6 ..................................08-8065

r134a

1) MiO 14 Hose Ftg., bulkhead 12 Ftg.


DESCRIpTION SIzE pART NO. DESCRIpTION SIzE pART NO.

sTrAigHT COMpressiON FiTTiNg 6 6 5/8”-18 08-3010B 08-3010BRMeTAl TO rubber 8 8 3/4”-16 08-3011B 08-3011BR 10 10 7/8”-14 08-3012B 12 12 1-1/16”-14 08-3013B 08-3013BR

10 8 3/4”-16 step Down 08-3014B 10 12 7/8”-14 step Down 08-3015B 08-3015BR 6 8 5/8”-18 step Down call 8 6 3/4”-16 step Down call

beADlOCk

hOSE FITTING FTG. hOSE FTG. STEp pART NO. pART NO. pART NO.CONFIGURATION SIzE SIzE ThREAD FTG. ALUm. STEEL Reduced Diameter

COmpRESSION FITTINGS (WIThOUT ChARGING pORT)


DESCRIpTION hOSE SIzE pART NO. DESCRIpTION hOSE SIzE pART NO.

beADlOCk

COmpRESSOR FITTINGS, TUbE-O TypE (also see sERVICE VAlVEs, page 435-439)

90 Degree FeMAle Tube-O COMp.FiTTiNg with r134a serViCe pOrT 8 (16mm port) ...... 08-3492BS1”-14 Thread, steel 10 (13mm port) ...... 08-3493BS

8 (reduced dia.) ......08-3492BR 10 (reduced dia.) ......08-3493BR

beADlOCk

45 Degree FeMAle Tube-O COMp.FiTTiNg with r134a serViCe pOrT 8 (16mm port) ...... 08-3442BS1”-14 Thread, steel 10 (13mm port) ...... 08-3443BS

TUbE and LINE REpAIR FITTING kITS

use for Metal line repairs on any A/C and Heater lines. (Can also be used on metal Transmission and power steering lines.)

LINE REPAIR KITS 5/16” O.D. line ...........................08-3100 3/8” O.D. line .............................08-3102 1/2" O.D. line.............................08-3104 5/8" O.D. line.............................08-3105 3/4" O.D. line.............................08-3106

step Down ..... 3/8” to 5/16” O.D. line ...............08-3101 step Down ..... 1/2” to 3/8” O.D. line .................08-3103

METRIC LINE REPAIR KITS 10mm O.D. line .........................08-3107 12mm O.D. line .........................08-3109 15mm O.D. line .........................08-3110 16mm O.D. line .........................08-3111

step Down ..... 12mm to 10mm O.D. line ..........08-3108


EVApORATOR INLET TUbE REpAIR kITS (with ORIFICE TUbE)

DESCRIpTION pART NO.

gM sTrAigHT OriFiCe repAir kiT ........................................08-3016 FOrD sTrAigHT OriFiCe repAir kiT ...................................08-3041

DESCRIpTION pART NO.

Compression fittings for Ford vehicles w/orifice tube in liquid line. Includes replaceable orifice tube. No. 8 x 8 Compression Fittings (1/2” O.D. Tubing) 3/4”-16 Nut; Blue Orifice Tube

Male Insert O-Ring No. 8 x 8 Compression Fittings(1/2” O.D. Tubing) 3/4”-16 Nut; Black & White Orifice Tube

Navistar prostar Oe# 3666274-C3

CCOT suCTiON Tube AssY. w/THerMisTOr ...................08-0806(uses #16-4296 O-ring and gasket kit)(o’rings: #16-4249; #16-4253)

DESCRIpTION pART NO.DESCRIpTION pART NO.


Navistar prostar Oe# 3670136-C91

CCOT suCTiON Tube AssY. w/THerMisTOr ...................08-0807(uses #16-4296 O-ring and gasket kit)(o’rings: #16-4249; #16-4253)

iNTerNATiONAl Oe# 3542578C2, bOA80-305-00-939

CCOT liQuiD Tube AssY. ....................................................08-0805 (uses #12-0805 orifice tube) (uses #16-4295 O-ring and gasket kit)(o’rings: #16-4248; #16-4252)

CCOT SUCTION LIQUID TUbE ASSEmbLIES

blOCk-OFF plugs (individual, sold ea.)

Female nut with plug Male nut with plugfor Male insert O-ring Fittings for Female insert O-ring Fittings#6 ...............................08-3077 #6 .................................08-3081#8 ...............................08-3078 #8 .................................08-3082#10 .............................08-3079 #10 ...............................08-3083#12 .............................08-3080 #12 ...............................08-3084

TXV blOCk-OFF plug kiT ..........................................................08-3042used on block Type expansion Valves (TXV) to close off unused, un-needed ports. supplied with 1 pc. each: #6, #8, #10 plug

#6

#6

#12

#12#12

13mm

includes sensor #11-0834

includes sensor #11-0834

#12

© 2014 Truckers AC 406406 © 2014 Truck Air Parts

Step 2. Slip on Two ClipsInstall two proper-sized clips onto the cut end of the hose. Orientation of the clips does not affect the performance of the connection. However, for ease of assembley, both clips should have the same orientation.

NOTE: Failure to slide the clips over the hose at this time will require the clips to be stretched over the hose or fitting later. This may permanently damage the clip.

Step 3. Oil the NippleLubricate the nipple with a generous amount of the refrigeration or A/C system’s compressor lubricating oil. This MUST be done to lower the force of the nipple insertion.

Step 4. Insert the Nipple into the HoseInsert the nipple into the hose. To ensure that the nipple is fully inserted, check the gap between the cut end of the hose and the shoulder on the nipple. Care should be taken to avoid kinking or other damage to the hose during nipple insertion.

NOTE: Be sure to wipe excess oil from the nipple and hose.

Step 5. Snap on the CageSnap the cage into the groove on the nipple. The arms should extend over the hose length. When the cage has been correctly installed in the cage groove, the cage will be able to rotate in the groove. This step MUST be performed to ensure:1. The clips will be located over the O’rings on the nipple.2. The connection will be compatible with the connection’s pressure rating.

Step 6. Slide the ClipsSlide the clips over the cage arms and into the channels on each arm.

Step 7. Close the Clips-6, -8, -10, -12 use #15-3242 pliers; (-16 use #15-3247) to close the clips. The pliers should be positioned squarely on the clip connection points and should remain square during the closing of the clip.

If the pliers are not kept square during closing of the clip, the clasp may have an offset. Use the pliers to correct the clasp alignment.

Nose of the pliers should be firmly seated under the assembly bump and lock latch. Note: -16 only, tap the top latch until fully seated.

E-z CLIp Assembly Instructions

Step 1. Cut the HoseCut the hose to proper length with an appropriate tool. The hand-held hose cutter has been specially designed for cutting all non-wire reinforced hose, such as GH134 multi-refrigerant hose. Be sure the cut is made square to the hose length.

Fittings — AEROQUIp E-z CLIp Section V: Illustrated

15-3242 Hose Pliers


Section V: Illustrated AEROQUIp E-z CLIp — Fittings

90° MALE O-RING 6 ............6 ..........08-5961E 8 ............8 ..........08-5962E 10 ..........10 ..........08-5963E 12 ..........12 ..........08-5964E 8 ..........10 ..........08-5965E 10 ..........12 ..........08-5974E

E-Z CLIP BULKHEAD 6 ............6 ..........08-8076EMIO STRAIGHT 8 ............8 ..........08-8078E 10 ..........10 ..........08-8080E

EZ-CLIP BULKHEAD 6 ............6 ..........08-8976EMIO 90° ELBOW 8 ............8 ..........08-8978E 10 ..........10 ..........08-8980E 10 ..........12 ..........08-8983E 12 ..........12 ..........08-8982E

DESCRIpTION FTG. hOSE pART NO.

STRAIGHT 6 ...........6 .........08-5061EMALE O-RING 8 ............8 .........08-5062E 10 .........10 .........08-5063E 12 .........12 .........08-5064E 10 .........12 .........08-5074E 6 ...........8 .........08-5075E 10 .........16 ..........08-5016E 12 .........16 .........08-5026E

STRAIGHT 6 ............6 ..........08-5051EMALE INSERT O-RING 8 ............8 ..........08-5052E 10 ..........10 ..........08-5053E 12 ..........12 ..........08-5054E 10 ..........12 ..........08-5056E


For use with E-z Clip type hose only, supplied with clips and cage.

mALE O-RING TypE mALE INSERT O-RING TypE

STRAIGHT 6 ...........6 .........08-5031E 1MALE O-RING 8 ............8 .........08-5032E 1R134a PORT 10 .........10 .........08-5036E 1 10 .........10 .........08-5033E 2 10 .........12 .........08-5035E 2


90° MALE O-RING M10 .........10 .........08-5984EMETRIC

STRAIGHT M20 .........10 .......08-5084EMALE O-RINGMETRIC

90° MALE INSERT O-RING 6 ............6 ..........08-5951E 8 ............8 ..........08-5952E 10 ..........10 ..........08-5953E

45° MALE O-RING 6 ............6 ..........08-5461E 8 ............8 ..........08-5462E 10 ..........10 ..........08-5463E

90° MALE O-RING 6 ............6 ..........08-5931E 1R134a PORT 8 ............8 ..........08-5932E 1 10 ..........10 ..........08-5933E 2 10 ..........12 ..........08-5935E 2 10 ..........10 ..........08-5936E 1

1 16mm port (high side)2 13mm port (low side)


mALE bULkhEAD TypE

DESCRIpTION FTG. hOSE pART NO.pILOT CONNECTION TypE

PILOT CONNECTION 8 ............8 ..........08-6902E90° ELBOW - Long Pilot 10 ..........10 ..........08-6903E 10 ..........12 ..........08-6905E



90° FEMALE O-RING 6 ............6 ..........08-6961E 8 ............8 ..........08-6962E 10 ..........10 ..........08-6963E 12 ..........12 ..........08-6964E 6 ............8 ..........08-6975E 8 ..........10 ..........08-6973E 10 ..........12 ..........08-6974E 10 ..........16 ..........08-6916E 12 ..........10 ..........08-6977E 12 ..........16 ..........08-6926E


FEmALE TypEDESCRIpTION FTG. hOSE pART NO.

STRAIGHT 6 ............6 ..........08-6061EFEMALE O-RING 8 ............8 ..........08-6062E 10 ..........10 ..........08-6063E 12 ..........12 ..........08-6064E 6 ............8 ..........08-6071E 8 ..........10 ..........08-6072E 10 ..........10 ..........08-6077E 1 10 ..........12 ..........08-6074E 12 ..........16 ..........08-6026E1 w/r12 port

STRAIGHT 6 ............6 ..........08-6031E 1FEMALE O-RING 8 ............8 ..........08-6032E 1R134a PORT 8 ..........10 ..........08-6035E 1 10 ..........10 ..........08-6033E 2 12 ..........12 ..........08-6034E 2 10 ..........12 ..........08-6037E 2



FEmALE TypE

STRAIGHT 6 ............6 ..........08-4061EFEMALE FLARE 8 ............8 ..........08-4062E 10 ..........10 ..........08-4063E


FEmALE FLARE TypE

90° FEMALE FLARE 6 ............6 ..........08-4961E 8 ............8 ..........08-4962E 10 ..........10 ..........08-4963E

45° FEMALE O-RING 6 ............6 ..........08-6461E 8 ............8 ..........08-6462E 10 ..........10 ..........08-6463E 12 ..........12 ..........08-6464E 6 ............8 ..........08-6471E 8 ..........10 ..........08-6472E 10 ..........12 ..........08-6474E 12 ..........16 ..........08-6426E

STRAIGHT M20 x 1.5 ......8.......08-6108EFEMALE O-RING M27 x 2 .....12.......08-6112E Long PilotMETRIC

STRAIGHT 10 ..........10 ..........08-6092EFEMALE O-RINGM10 x 1.25 SWITCH PORTLong Pilot

STRAIGHT 10 ..........10 ..........08-6095EFEMALE O-RING 10 ..........12 ..........08-6097EM12 x 1.5 SWITCH PORT 12 ..........12 ..........08-6096ELong Pilot

45° FEMALE O-RING 8 ............8 ..........08-6432E 1R134a PORT 10 ..........10 ..........08-6433E 2Short Pilot

M12

M10

90° O.R.S. FEMALE O-RING ORS ..........6 ..........08-6936ESPECIAL QUICK DISCONNECT ORS ..........8 ..........08-6938E(flat surface type o’ring) ORS ........10 ..........08-6940E ORS ........12 ..........08-6942E

90° FEMALE O-RINGMETRIC w/o PORT .................................. 20mm ..............8 .........08-6188E



Section V: Illustrated AEROQUIp E-z CLIp — Fittings

90° FEMALE O-RING 6 ............6 ..........08-6931E 1R134a PORT 8 ............8 ..........08-6932E 1 8 ..........10 ..........08-6935E 1 10 ..........10 ..........08-6933E 2 12 ..........12 ..........08-6934E 2 10 ..........12 ..........08-6937E 2



90° FEMALE O-RING 10 ..........10 ..........08-6987ER12 SWITCH PORT 12 ..........12 ..........08-6988E 10 ..........12 ..........08-6989E

FEmALE TypEDESCRIpTION FTG. hOSE pART NO.

90° FEMALE O-RING 8 ............8 ...........08-6998ER134a HIGH SIDE PORT and M10 SWITCH PORT Short Pilot

R12

90° FEMALE O-RING 10 ..........10 ..........08-6995EM12 x 1.5 SWITCH PORT 10 ..........12 ..........08-6997ELong Pilot 12 ..........12 ..........08-6996E

M12

90° SPLICER 6 ............6 ..........08-3025E 8 ............8 ..........08-3026E 12 ..........12 ..........08-3028E

T-SPLICER 8 x 8 x 8 ........................08-3018E 10 x 10 x 10 ........................08-3019E 12 x 12 x 12 ........................08-3020E

STRAIGHT SPLICER 6 ............6 ..........08-3000E 8 ............8 ..........08-3001E 10 ..........10 ..........08-3002E 12 ..........12 ..........08-3003E 16 ..........16 ..........08-3007E

COmpRESSION FITTINGS

DESCRIpTION FTG. hOSE ThRD. pART NO.

COmpRESSOR FITTINGS

90° COMPRESSOR FITTINGROTOLOCK FEMALE Rotolock ..... 12 ....................... 08-3096E

90° COMPRESSOR FITTINGTUBE-O FEMALE Tube-O ....... 8 ....... 1-14........ 08-3094E Tube-O ..... 10 ....... 1-14........ 08-3095E

STRAIGHT COMPRESSOR FITTINGTUBE-O FEMALE Tube-O ..... 10 ....... 1-14........ 08-3404E

STRAIGHT 6 ............6 ..........08-3010ECOMPRESSION 8 ............8 ..........08-3011E 10 ..........10 ..........08-3012E 10 ..........12 ..........08-3015E 12 ..........12 ..........08-3013E


SpLICERSDESCRIpTION FTG. hOSE pART NO.

16mmM10

A6 Compressors 8 ............8 ..........08-3045E90° SWIVEL FITTING 10 ..........10 ..........08-3046E 12 ..........12 ..........08-3047E

STRAIGHT SPLICER 6 ............6 ..........08-3421E 1R134a PORT 8 ............8 ..........08-3422E 1 10 ..........10 ..........08-3423E 2 12 ..........12 ..........08-3424E 2 10 ..........10 ..........08-3429E 1 16 ..........16 ..........08-3416E 2



hOSE TUbE SIzE O.D. pART NO.

STRAIGHT SPLICERM10 x 1.25 SWITCH PORT 8 ............8 ............ 08-3450E(High Side) 10 ..........10 ............ 08-3451E

M12 x 1.5 SWITCH PORT 12 ..........12 ............ 08-3452E(Low Side)



DESCRIpTION FTG. pART NO.

SpLICERS

CAGES and CLIpS

90° TEE STYLE 12 ..... 08-8144E Male Insert O’ring x 27mm Female O’ring x 12 Hose

Y-SPLICER 8x8x8 .................. 08-3438E

E-Z CLIP CAGE 6 .......................... 09-1006E(sold each) 8 .......................... 09-1008E 10 .......................... 09-1010E 12 .......................... 09-1012E 16 .......................... 09-1016E

E-Z CLIP CLIP 6 .......................... 09-1106E(2 required, sold each) 8 .......................... 09-1108E 10 .......................... 09-1110E 12 .......................... 09-1112E 16 .......................... 09-1116E

E-Z CLIP and CAGE KIT 6 .......................... 09-1028E(1 Cage and 2 Clips) 8 .......................... 09-1029E 10 .......................... 09-1030E 12 .......................... 09-1031E 16 .......................... 09-1032E

STRAIGHT SPLICER 6 ............6 ............ 08-3431ER12 SWITCH PORT 8 ............8 ............ 08-3432E 10 ..........10 ............ 08-3433E 12 ..........12 ............ 08-3434E

WELD-ON TypEDESCRIpTION FTG. hOSE pART NO.

WELD-ON FITTINGS 6 ............6 .............08-8100ELIFESAVERS (steel) 6 ............8 .............08-8106E 8 ............8 .............08-8101E 8 ..........10 .............08-8107E 10 ..........10 .............08-8102E 10 ..........12 .............08-8105E 12 ..........12 .............08-8103E 16 ..........16 .............08-8109E

DESCRIpTION FITTING ThREAD hOSE hOSE pART NO.

TEE FITTING TypE

TEE STYLE 3/4”-16 .....#8 MIO...... 8 .........8 ..... 08-3123E 7/8”-14 ...#10 MIO.... 12 .......12 ..... 08-3124E 1-1/16”-14 ...#12 MIO.... 16 .......16 ..... 08-3125E

E-z Clip Lifesaver kitsEach KIT contains the correct components for replacement of a single hose assembly. The Aluminum Lifesaver Braze Fitting Kits are designed to rework failed OEM aluminum air conditioning tubing and hose assemblies in sizes 10mm to 18mm (metric tubing only, -6 to –12). This repair system allows the installer to reuse unique OEM terminal connections, while replacing the failed OEM hose and nipple with the E-Z Clip attachment system.

KIT COMPONENTSQty. Description2 ea.................Braze-on Nipple5 ea.................Nipple O-ring3 ea.................Silver Braze Ring1 ea.................Assembly Instructions

#6 ............ 8mm ............. 08-8124EK #8 ............ 10mm ........... 08-8125EK #10 .......... 16mm ........... 08-8126EK #12 .......... 18mm ........... 08-8127EK

R12 Male

(NOTe: o-rings, clips and cages not included)

Male Insert O’ring Connections



• Save Time

• Eliminate Leaks

• New, Simple, Fast and Easy

• Use with Reduced Diameter Hose

• Burgaclips’ state-of-the-art hose fittings are a breakthrough in the a/c industry.• A simple procedure to attach fittings to the hose.• This hose and fitting combo provides a permeation rate which is 74% less than the presently available hose assemblies in the marketplace.

bURGACLIp FITTINGS1. 3.2.

go....

how To Install Instructions

1. Cut hose to proper length. Use reduced diameter hose only.2. Place two proper size clips into the clip holder. For ease of assembly, both clips should have the same

orientation.3. Slip in the clipholder with the clips. Place the clipholder with the two clips on the hose. In such a manner that

the side with the smallest hole touches the end of the hose.4. Lubricate the fitting with a generous amount of the a/c systems lubricator oil (this lowers the force of insertion)5. Insert the Burgaclip fitting into the hose. Ensure that the fitting is fully inserted by checking the gap between the

end of the hose and the shoulder of the fitting.6. Close the clips with the Burgaflex clip pliers (#15-3243BC). The pliers open themselves when the correct

amount of force has been reached. Start with the clip closest to the end of the hose. DONE !

Section V: Illustrated bURGACLIp — Fittings


08-6931BC 6 6R 16mm R134a08-6932BC 8 8R 16mm R134a08-6933BC 10 10R 13mm R134a08-6934BC 12 12R 13mm R134a

08-5951BC 6 6R w/o port08-5952BC 8 8R w/o port08-5953BC 10 10R w/o port

mALE O’RINGFEmALE O’RING

08-5051BC 6 6R w/o port08-5052BC 8 8R w/o port08-5053BC 10 10R w/o port08-5054BC 12 12R w/o port

Fitting HosePart # Size Size Port

MALE INSERT O’RINGSTRAIGHT

90° MALE INSERT O’RING


90° MALE O’RINGwith R134a PORT

90° MALE O’RING




STRAIGHT MALE O’RING


STRAIGHT FEMALE O’RING


08-6061BC 6 6R w/o port08-6076BC 8 6R w/o port08-6062BC 8 8R w/o port08-6063BC 10 10R w/o port08-6074BC 10 12R w/o port08-6064BC 12 12R w/o port


90° FEMALE O’RING

08-6961BC 6 6R w/o port08-6976BC 8 6R w/o port08-6962BC 8 8R w/o port08-6973BC 8 10R w/o port08-6963BC 10 10R w/o port08-6974BC 10 12R w/o port08-6977BC 12 10R w/o port08-6964BC 12 12R w/o port


STRAIGHT FEMALE O’RING with R134a PORT

08-6031BC 6 6R 16mm R134a08-6032BC 8 8R 16mm R134a08-6033BC 10 10R 13mm R134a08-6037BC 12 10R 13mm R134a 08-6034BC 12 12R 13mm R134a


90° FEMALE O’RINGwith R134a PORT



45° FEMALE O’RING



08-3492BC 1-14” 8R 16mm R134a08-3493BC 1-14” 10R 13mm R134a08-3497BC 1-14” 12R 13mm R134a

90° TUBE-O 1”-14 with R134a PORT

08-5931BC 6 6R 16mm R134a08-5932BC 8 8R 16mm R134a08-5933BC 10 10R 13mm R134a08-5935BC 12 12R 13mm R134a

All burgaclip Fittingssupplied with

Cage and Clips.

Fittings — bURGACLIp Section V: Illustrated

© 2014 Truckers AC 413413© 2014 Truck Air Parts

Section V: Illustrated bURGACLIp — Fittings

15-3008 ...... HOSE CUTTER 15-3009 ...... BLADE for #15-3008

15-3243BC BURGAFLEX CLIP PLIERSfor all sizes #6 thru #14

Fitting Hose Part # Size Size O.D.

BARRIER HOSE(reduced size)

09-5046 # 6 5/16” I.D. 39/64”09-5048 # 8 13/32” I.D. 45/64”09-5050 #10 1/2” I.D. 25/32”09-5052 #12 5/8” I.D. 61/64”09-5054 #14 3/4” I.D. 1-1/8”(rolls 50 ft. each)


SPLICER 3-WAY (“T”)

08-3017BC 6x6x6 6R w/o port08-3018BC 8x8x8 8R w/o port08-3019BC 10x10x10 10R w/o port08-3020BC 12x12x12 12R w/o port

SPLICER STRAIGHT

Fitting HosePart # Size Size

08-3000BC 6 6R 08-3001BC 8 8R08-3002BC 10 10R 08-3003BC 12 12R 08-3101BC 12 14R w/clips only08-3100BC 14 14R w/clips only


STRAIGHT SPLICER with R134a PORT

TOOLS

08-3421BC 6 6 16mm R134a08-3422BC 8 8 16mm R134a08-3423BC 10 10 13mm R134a08-3424BC 12 12 13mm R134a

Part # Size

CLIPS

09-1106BC # 6 09-1108BC # 8 09-1110BC #10 09-1112BC #1209-1114BC #14

Part # Size

CLIP HOLDERBRAZE NIPPLES (Steel)(w/o cage/clips)

08-8100BC 3/8” # 6R08-8101BC 1/2” # 8R08-8102BC 5/8” #10R08-8103BC 3/4” #12R

09-1006BC # 6 09-1008BC # 8 09-1010BC #10 09-1012BC #12

90° SPLICER



90° BEAD w/o NUT



KENWORTHHARDLINE FITTING

with PORTS

08-1020BC 8 8R M10 (2) 16mm (1)


Note: All fittings (exc. Braze Nipples) include clips and holder.

Fitting HosePart # Size Size


HOSE FITTING FTG. HOSE FTG. STEP PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD FTG. AlUM. STEEl

beADlOCk

beADlOCk

hOSE FITTINGS — FLARE FEmALE (WIThOUT ChARGING pORT)

sTrAigHT FeMAle FlAre 6 6 5/8”-18 08-4061BS 8 8 3/4”-16 08-4062BS 10 10 7/8”-14 08-4063BS

45 Degree FeMAle FlAre 8 8 3/4”-16 08-4462BS 10 10 7/8”-14 08-4463BS

90 Degree FeMAle FlAre 6 6 5/8”-18 08-4961BS 8 8 3/4”-16 08-4962BS 10 10 7/8”-14 08-4963BS

Fittings — hOSE Section V: Illustrated

90° ELBOW 6 6 - 16MM 08-7916B (high side)

hOSE FITTINGS — (WITh SERVICE pORT)

HOSE FITTING FTG. HOSE FTG. PORT PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD SIZE AlUM. STEEl AlUM. 10Pk

90 Degree MAle iNserT O-riNg 6 6 5/8”-18 08-5951BS 8 8 3/4”-16 08-5952BS 10 10 7/8”-14 08-5953BS

HOSE FITTING FTG. HOSE FTG. STEP PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD FTG. AlUM. STEEl

beADlOCk

hOSE FITTINGS — O-RING mALE INSERT TypE (mIO) / WIThOUT ChARGING pORTS

Steel ReducedDiameter

sTrAigHT MAle iNserT O-riNg 6 6 5/8”-18 08-5051BS 8 8 3/4”-16 08-5052BS 10 10 7/8”-14 08-5053BS 12 12 1-1/16”-14 08-5054BS

beADlOCk

beADlOCk


90 Degree MAle O-riNg 6 6 5/8”-18 08-5961BS 6 6r 5/8”-18 08-5961BR 7 6 11/16”-16 iHC/gMC 08-5921BS 7 6r 11/16”-16 iHC/gMC 08-5921BR 6 8 3/4”-18 08-5971BS 8 8 3/4”-18 08-5962BS 8 8r 3/4”-18 08-5962BR 10 10 7/8”-18 08-5963BS 10 10r 7/8”-18 08-5963BR 12 12 1-1/16”-16 08-5964BS 08-5964BR 10 12 7/8”-18 step Down 08-5974BS 10 12r 7/8”-18 step Down 08-5974BRbeADlOCk

45 Degree MAle O-riNg 6 6 5/8”-18 08-5461BS 8 8 3/4”-18 08-5462BS 10 10 7/8”-18 08-5463BS 12 12 1-1/16”-16 08-5464BS

beADlOCk

sTrAigHT MAle O-riNg 6 6 5/8”-18 08-5061BS 08-5061BS-10 6 6r 5/8”-18 08-5061BR 7 6 11/16”-16 iHC/gMC 08-5021BS 7 6r 11/16”-16 iHC/gMC 08-5021BR 6 8 3/4”-18 step up 08-5071BS 08-5071BR 8 8 3/4”-18 08-5062BS 8 8r 3/4”-18 08-5062BR

10 10 7/8”-18 08-5063BS 08-5063BS-10 10 10r 7/8”-18 08-5063BR 10 12 1-1/16”-16 step Down 08-5074BS 10 12r 1-1/16”-16 step Down 08-5074BR 12 12 1-1/16”-16 08-5064BS 12 12r 1-1/16”-16 08-5064BRbeADlOCk

hOSE FITTINGS — O-RING mALE / WIThOUT ChARGING pORT

HOSE FITTING FTG. HOSE FTG. STEP PART NO. PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD FTG. AlUM. STEEl Steel Reduced Diameter

Section V: Illustrated hOSE — Fittings


sTrAigHT MAle O-riNg 10 10 7/8”-14 10MM 08-5093BS

10 12 7/8”-14 10MM 08-5097BS

HOSE FITTING FTG. HOSE FTG. PORT PART NO. PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD SIZE AlUM. STEEl AlUM. 10Pk STEEl 10Pk.

sTrAigHT MAle O-riNg 6 6 5/8”-18 16MM 08-5031BS 10 10 7/8”-14 13MM 08-5033BS 10 12 7/8”-14 13MM 08-5038BS

90 Degree MAle O-riNg 6 6 5/8”-18 16MM 08-5931BS 10 10 7/8”-14 13MM 08-5933BS 10 12 7/8”-14 13MM 08-5938BS

hOSE FITTINGS — O-RING mALE / WITh R134a ChARGING pORTS

beADlOCk

hOSE FITTINGS — O-RING-mALE / WITh mETRIC R134a SWITCh pORT

beADlOCk


beADlOCk




45 Degree FeMAle O-riNg 6 6 5/8”-18 08-6461BS 08-6461BS-10 6 6r 5/8”-18 08-6461BR 8 8 3/4”-16 08-6462BS 08-6462BS-10 8 8r 3/4”-16 08-6462BR 10 10 7/8”-14 08-6463BS 08-6463BS-10 10 10r 7/8”-14 08-6463BR 12 12 1-1/16”-14 08-6464BS 08-6464BR

10 12 1-1/16”-14 step Down 08-6474BS

beADlOCk

HOSE FITTING FTG. HOSE FTG. STEP PART NO. PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD INFO AlUM. STEEl STEEl 10Pk.


hOSE FITTINGS — O-RING (SpECIAL) “QUICk DISCONNECT”

sTrAigHT Q.D. (MAle) #4QD 6 1/2”-20 08-5100BSFits onto Quick Coupler #08-5104 #4QD 6 1/2”-20 08-5100BR

QuiCk DisCONNeCT (FeMAle) #10 #10 08-8025beADlOCk FTg.

hOSE FITTINGS — O-RING FEmALE / WIThOUT ChARGING pORTS

beADlOCk

(continued)

beADlOCk

sTrAigHT FeMAle O-riNg 6 6 5/8”-18 08-6061BS 08-6061BS-10 6 6r 5/8”-18 08-6061BR 8 8 3/4”-16 08-6062BS 08-6062BS-10 8 8r 3/4”-16 08-6062BR 10 10 7/8”-14 08-6063BS 08-6063BS-10 10 10r 7/8”-14 08-6063BR 12 12 1-1/16”-14 08-6064BS 12 12r 1-1/16”-14 08-6064BR

6 8 5/8”18 step Down 08-6071BS 8 6 3/4”-16 step up 08-6076BS 8 10 3/4”-16 step Down 08-6072BS 10 12 7/8”-14 step Down 08-6074BS 10 12 7/8”-14 step Down 12 10 1-1/16”-14 step up 08-6077BS 12 14r 1-1/16”-14 step Down 08-6079BR



QuiCk DisCONNeCT COupler AssY ......... ........................08-51041/2”-20 FTg. THreADincludes Valve kitfits Drier#07-3072A

replACeMeNT VAlVe kiT ................................................ 08-5104VK


90 Degree FeMAle O-riNg 6 6 5/8”-18 08-6961BS 08-6961BS-10 6 6r 5/8”-18 08-6961BR 8 8 3/4”-16 08-6962BS 08-6962BS-10 8 8r 3/4”-16 08-6962BR 10 10 7/8”-14 08-6963BS 08-6963BS-10 10 10r 7/8”-14 08-6963BR 12 12 1-1/16”-14 08-6964BS 12 12r 1-1/16”-14 08-6964BR

6 8 5/8”18 step Down 08-6975BS 08-6975BR 8 6 3/4”-16 step up 08-6976BS 8 10 3/4”-16 step Down 08-6973BS 08-6973BR 10 12 7/8”-14 step Down 08-6974BS 12 10 1-1/16”-14 step up 08-6977BS 12 14r 1-1/16”-14 step Down 08-6979BRbeADlOCk

HOSE FITTING FTG. HOSE FTG. STEP PART NO. PART NO. A BcONFIGURATION SIZE SIZE THREAD INFO AlUM. STEEl


beADlOCk

90 Degree FeMAle O-riNg “sHOrT DrOp” ANgle 8 8 3/4”-16 08-6962BD 0.094” 0.071” 10 10 7/8”-14 08-6963BD 1.00” 0.071”

10 12 7/8”-14 step Down 08-6974BD 1.12” 0.071”

hOSE FITTINGS — O-RING FEmALE / WIThOUT ChARGING pORT

hOSE FITTINGS — O-RING FEmALE (SpECIAL) / WIThOUT ChARGING pORTS

A

B

(continued)

HOSE FITTING FTG. HOSE FTG. PORT PART NO. PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD SIZE AlUM. STEEl STEEl 10Pk.

hOSE FITTINGS — O-RING FEmALE / WITh R12 ChARGING pORT

sTrAigHT FeMAle O-riNg 6 6 5/8”-18 1/4” 08-6085BS 8 8 3/4”-16 1/4” 08-6086BS

90 Degree FeMAle O-riNg 6 6 5/8”-18 1/4” 08-6985BS 8 8 3/4”-16 1/4” 08-6986BS 10 10 7/8”-14 1/4” 08-6987BS 10 12 7/8”-14 1/4” 08-6989BS

beADlOCk

beADlOCk






90 Degree FeMAle O-riNg 6 6 5/8”-18 16MM 08-6931BSwiTH TOp CHArgiNg pOrT 6 6r 5/8”-18 16MM 08-6931BR 8 8 3/4”-16 16MM 08-6932BS 8 8r 3/4”-16 16MM 08-6932BR 10 10 7/8”-14 13MM 08-6933BS 10 10r 7/8”-14 13MM 08-6933BR 12 12 1-1/16”-14 13MM 08-6934BS 10 12 7/8”-14 13MM 08-6937BS 10 12r 7/8”-14 13MM 08-6937BR 12 14r 1-1/16”-14 13MM 08-6939BR

45 Degree FeMAle O-riNg 6 6 5/8”-18 16MM 08-6431BS 8 8 3/4”-16 16MM 08-6432BS 10 10 7/8”-14 13MM 08-6433BS 10 12 7/8”-14 13MM 08-6437BS

sTrAigHT FeMAle O-riNg 6 6 5/8”-18 16MM 08-6031BS 6 6r 5/8”-18 16 MM 08-6031BR 8 8 3/4”-16 16MM 08-6032BS 8 8r 3/4”-16 16 MM 08-6032BR 10 10r 7/8”-14 16 MM 08-6033BR 10 10 7/8”-14 13MM 08-6033BS 10 12 7/8”-14 13MM 08-6037BS 08-6037BR 12 12 1-1/16”-14 13 MM 08-6034BS

HOSE FITTING FTG. HOSE FTG. PORT PART NO. PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD SIZE AlUM. STEEl STEEl 10Pk.

beADlOCk

hOSE FITTINGS — O-RING FEmALE / WITh R134a ChARGING pORT

hOSE FITTINGS — O-RING FEmALE / w/R134a ChARGING pORT and mETRIC SWITCh pORT(also see FIElD REPAIR FIttIngs, pages 423-425)

90 Degree FeMAle O-riNg 8 8 3/4”-16 16MM M10 08-6982BS 1wiTH swiTCH pOrT & TOp 8 8 3/4”-16 16MM M10 08-6983BS 2

r134a CHArgiNg pOrT 8 8 3/4”-16 16MM M10 08-6998BR 3 (reduced dia.) 8 8 3/4”-16 16MM M10 08-6998BS 3

HOSE FITTING FTG. HOSE FTG. R134a SWITcH PART NO. cONFIGURATION SIZE SIZE THREAD PORT PORT STEEl

beADlOCk

beADlOCk

08-6982BS

(1) leFT pOrT

08-6983BS08-6998BR08-6998BS

(2) rigHT pOrT

(3) TOp pOrT



45 Degree FeMAle O-riNg M16 6 M16-1.5 08-6144BS

M E T R I C

16MM

CHArge pOrT

M10 swiTCH pOrT

sTrAigHT FeMAle O-riNg #5 6 9/16”-18 08-6103B 1 7 mm 3/4” 16-4278 M16 6 M16-1.5 08-6104BS M20 6 M20-1.5 08-6106B 11 mm 15/16” 16-4280

M20 8 M20-1.5 08-6108B 11 mm 15/16” 16-4280

M24 10 M24-2.0 08-6111B 14 mm 1-1/16” 16-4281

HOSE FITTING FTG. HOSE FTG. PART NO. PART NO. O-RINGcONFIGURATION SIZE SIZE THREAD STEEl AlUM. PART NO.


sTrAigHT FeMAle O-riNg 6 6 5/8”-18 M10 08-6091BS 8 8 3/4”-16 M10 08-6092BS 8 8 3/4”-16 M10 08-6098BS 1 10 10 7/8”-14 M10 08-6093BS

90 Degree FeMAle O-riNg 6 6 5/8”-18 M10 08-6991BS 8 8 3/4”-16 M10 08-6992BS 10 10 7/8”-14 M10 08-6993BS 10 12 7/8”-14 M10 08-6997BS

hOSE FITTINGS — O-RING FEmALE / WITh mETRIC R134a and m10 SWITCh pORT

hOSE FITTINGS — O-RING FEmALE / WITh mETRIC ThREADS (SLOT IN NUT)metric O-rings not included - Available in 10 packs each size

90 Degree FeMAle O-riNg M16 6 M16-1.5 08-6184BS M20 8 M20-1.5 08-6188B 11 mm 15/16” 16-4280

beADlOCk

beADlOCk

M E T R I CbeADlOCk

beADlOCk

slOT

slOT

M10 swiTCH pOrT

M10 swiTCH pOrT

1 with 16mm port

A b

A

A

b

b

(see illustration)

M E T R I CbeADlOCk




HOSE FITTING FTG. HOSE FTG. STEP PART NO. PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE THREAD FTG. AlUM. STEEl AlUM. 10Pk STEEl 10Pk.

spliCer Tips-iNNer lip DesigN 6 6 NONe 08-8120Cut off original hose at crimp, and 8 8 NONe 08-8111 08-8121weld tip onto old fitting. 10 10 NONe 08-8112 08-8122 12 12 NONe 08-8123

spliCer Tips-OuTer lip DesigN 6 6 NONe 08-8124 08-8100Cut off original hose at crimp, and 8 8 NONe 08-8125 08-8101weld tip onto old fitting. 10 10 NONe 08-8126 08-8102 12 12 NONe 08-8127 08-8103

REpAIR FITTINGS / SOLDER / WELD-ON

bArbeD eND

bArbeD eND

eVApOrATOr repAir FiTTiNgs 8 8 3/4”-16 08-8118 brAss MAle O-riNg sTrAigHT 10 10 7/8”-14 08-8119can be brazed/welded onto the ends of copper tubes, found on Red Dot evaporators.

spliCer Tips-OuTer lip DesigN 6 6 NONe 08-8124B 08-8100BCut off original hose at crimp, and 6 6r NONe 08-8100BR 1weld tip onto old fitting. 8 8 NONe 08-8125B 08-8101B 8 8r NONe 08-8125BR 08-8101BR 1 10 10 NONe 08-8126B 08-8102B 10 10r NONe 08-8126BR 1 08-8102BR 1 12 12 NONe 08-8127B 08-8103B 12 12r NONe 08-8127BR 1 08-8103BR 1

10 12 NONe step Down 08-8128B 10 12 NONe step Down 08-8128BR 1 10 12 NONe step Down 08-8105B 10 12r NONe step Down 08-8105BR 1 12 14r NONe step Down 08-8114BR 1

CONDeNser repAir FiTTiNgs 6 6 5/8”-18 08-8106A 08-8106 brAss MAle iNserT O-riNg 8 8 3/4”-16 08-8108A 08-8108

beADlOCk

1 reduced Diameter

Can be brazed/welded onto the ends of 3/8” copper tubes, found on red Dot grilledensers.

EZ clIP STYlE WElD-ON FITTINGS (lIFESAVERS) see page 410.


sTrAigHT spliCer 6 6 NONe 08-3000BS 6r 6r NONe 08-3000BR 8 8 NONe 08-3001BS 8r 8r NONe 08-3001BR 10 10 NONe 08-3002BS 10r 10r NONe 08-3002BR 12 12 NONe 08-3003BS 12r 12r NONe 08-3003BR

6 8 NONe step up 08-3004BS 08-3004BR 8 10 NONe step up 08-3005BS 08-3005BR 10 12 NONe step up 08-3006BS 08-3006BR 12r 14r NONe step up 08-3101BR

HOSE FITTING HOSE HOSE PORT STEP PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE SIZE FTG. AlUM. STEEl

hOSE FITTINGS — SpLICERS

sTrAigHT spliCer 6 6 NONe 08-3000 8 8 NONe 08-3001 10 10 NONe 08-3002 12 12 NONe 08-3003

spliCer Tee 6X6 6 NONe 08-3017BS 6X6 6 NONe 08-3017BR 8X8 8 NONe 08-3018BS 08-3018BR 10X10 10 NONe 08-3019BS 08-3019BR 12X12 12 NONe 08-3020BS

bArbeD eND

beADlOCk

beADlOCk


To be Discontinued upon depletion of stock.

90 Degree spliCer 6 6 NONe 08-3025BS 8 8 NONe 08-3026BS 10 10 NONe 08-3027BS 12 12 NONe 08-3028BS

beADlOCk


Tube and Line Repair Compression Fittings (#08-3100 thru #08-3111) see page 404.



spliCer wiTH r12 serViCe pOrT 6 6 1/4” 08-3021BS 8 8 1/4” 08-3022BS 10 10 1/4” 08-3023BS 12 12 1/4” 08-3024BS

spliCer wiTH r134a 6 6 16MM 08-3421BSserViCe pOrT 6r 6r 16MM 08-3421BR 8 8 16MM 08-3422BS 8r 8r 16MM 08-3422BR

10 10 13MM 08-3423BS 10r 10r 13MM 08-3423BR

10 10 16MM 08-3429BS 10r 10r 16MM 08-3429BR

12 12 13MM 08-3424BS 12r 12r 13MM 08-3424BR 14r 14r 13MM 08-3103BR

HOSE FITTING HOSE HOSE PORT PART NO. PART NO. PART NO. PART NO.cONFIGURATION SIZE SIZE SIZE AlUM. STEEl STEEl 10Pk.

beADlOCk

beADlOCk

r12

r134a

hOSE FITTINGS — SpLICERS / WITh SERVICE pORTS


Male Insert O-ring

Male Insert O-ring

SPLICER - STRAIGHTCharging Port ....... 16MMSwitch Port ........... M10 Reduced Dia.08-3431BR ................. #6FREIGHTLINER

SPLICER - w/Brkt - 80°Charging Port ....... 16MMSwitch Port ........... M10 Reduced Dia.08-3430BR ................. #6FREIGHTLINER

SpLICERS WITh SERVICE pORTS

SPLICER - w/Brkt - 80°Charging Port ....... 16MMSwitch Port ............M10 MIO08-3430SM ................ #6FREIGHTLINER

FIELD REPAIR SPLICERCharging Port ....... 16MMSwitch Port ............M10 MIO08-3431SM ............... #6FREIGHTLINER

see p.425

see p.425


Male Insert O-ring

FIELD REPAIR FITTING90° DegreeCharging Port ....... 16MMSwitch Port ............M10#8 Beadlock (Reduced Dia.) Female08-6998BR ................. #8PACCAR

HARDLINE FITTINGCONDENSER Charging Port ....... 16MMM10 Port (2) Female MIO08-1022S .....#8 ......... #8PACCAR

HARDLINE FITTINGCONDENSERBeadlock Reduced Dia. Charging Port ....... 16MMM10 Port (2) Female Reduced08-1022SR ...#8 ......... #8 PACCAR

HARDLINE FITTINGLIQUID Female MIO08-1023S ....#6 .......... #6PACCAR

HARDLINE FITTINGCONDENSER Beadlock Reduced Dia.M10 Port, Discharge Ftg. Female Reduced08-1021SR ...#8 ......... #8KENWORTH

HARDLINE FITTINGLIQUID Female MIO08-1024S ....#6 .......... #6PACCAR

HARDLINE FITTINGCONDENSER Female MIO08-1025S ....#6 .......... #6PACCAR

FIELD REPAIR FITTINGSTRAIGHT M10 Port (2) w/#6 MIO Connection Male08-5091MP ................ #6PACCAR

FIELD REPAIR FITTING80° DegreeM10 Port (2) w/#6 MIO Connection Male08-5991MP ................ #6PACCAR

FIELD REPAIR FITTING90° DegreeSteel Long Drop w/#6 MIO Connection Female08-6961ML ................. #6PACCAR

FIELD REPAIR FITTINGSTRAIGHT M10 Port (2) w/#8 MIO Connection Female08-6082MP ................ #8PACCAR

FIELD REPAIR FITTING90° DegreeCharging Port ....... 16MMSwitch Port ............M10w/#8 MIO Connection Female08-6998M1 ................. #8PACCAR

FIELD REPAIR FITTING90° DegreeM10 Port (2) w/#8 MIO Connection Female08-6998M2 .................#8PACCAR

Listed in ascending order by part number.

FIELD REPAIR SPLICERCharging Port ....... 16MMSwitch Port ............M10 MIO08-3431SM ............... #6FREIGHTLINER

Fittings — FIELD REpAIR and hARDLINE Section V: Illustrated

HARDLINE FITTINGCharging Port ....... 16MMM10 Port (2) Female MIO08-1020S .....#8 ......... #8 PACCAR

HARDLINE FITTINGBeadlock Reduced Dia.Charging Port ....... 16MMM10 Port (2) Female Reduced08-1020SR ...#8 .......... #8 PACCAR

see p.425

see p.425

see p.425

see p.425

see p.425

see p.425

see p.425

see p.425

see p.425

see p.425

see p.425see p.425


FIELD REPAIR FITTINGLiquid/SuctionPad/Tube #6 x #10MIO Connections MIO08-0608S ......... #6 x #10

FIELD REPAIR FITTING90° Degree, Pad Fitting#12 Beadlock (Reduced Dia.)(Accumulator #07-1409A) 08-1400SR ...............#12PETERBILT

Section V: Illustrated FIELD REpAIR and hARDLINE — Fittings

Also see additional Field Repair Fittings

on page 431-433.

FITTING TYPE PAD PART FTG. NO.

FITTING TYPE PAD PART FTG. NO.

J-BLOCK FITTING ........................................................08-0611FREIGHTLINER A22-57096-000

J-bLOCk FITTINGS J-bLOCk FITTINGS

pAD FITTINGS

16-4212#12 Std O-ring

J-BLOCK FITTING ........................................................08-0612FREIGHTLINER A22-54748-000

On Field Repair Fittings and Hardlines (as noted on pages 423-424)

The fittings and hardlines supplied are all designed as field-repair replacement items only. They do not have crimp-on shells attached. Instead, they have male insert o-ring ends. This allows the technician to couple a female o-ring fitting onto the end, which can then be crimped onto the hose. This also allows use of any type of hose (Goodyear standard or reduced, E-Z Clip, etc.) and any configuration of fitting (straight, 45°, 90°). See illustration.

NOTE

Example: 08-1020S

K.W. Original Equipment Hose

Field Repair Hose


Step 2. Slip on the Double Clamp Place the double clamp on the cut end of the SAE J2064 Type E refrigerant hose in such a way that the tooth of the bar comes in contact with the cut end of the hose.

Step 3. Oil the NippleLubricate the end of the coupling joint with a generous amount of lubricating oil. Use the same lubricate oil as used in air conditioning systems.

Step 4. Insert the Fitting Into the HoseFind the correct orientation and insert the fitting completely into the hose.

Step 5. Fit the Coupling in PlaceA. Position the round nose of the “CLIC” open-close pliers at the hook shaped end of the clamp. B. Position the thin nose of the “CLIC” open-close pliers at the end with the hooked teeth. C. Tighten the clamp until the click. To Disassemble - just reverse the position of the ends of the pliers on the clamp.

NOTE: The pliers should be positioned squarely on the clip connection points and should remain square during the closing of the clip.

FRIGOCLIC® Fittings Assembly Instructions

BLACK HOSE HOSE HOSE PART# END LENGTH

Refri*masterplus SAE J2064 Type EHOSE and CUTTER

09-7036 #6 70 ft09-7038 #8 75 ft09-7040 #10 75 ft09-7042 #12 60 ft

15-3265 HOSE CUTTER

09-1028Q #6 clamp 09-1016Q09-1029Q #8 clamp 09-1017Q09-1030Q #10 clamp 09-1018Q09-1031Q #12 clamp 09-1019Q

15-3243 CLIC PLIERS

for BLACK HOSE HOSE END for GREY HOSE PART # CLAMP PART #

Step 1. Cut the HoseCheck the dimensions of the components. Cut the end of the hose to proper length in a perpendicular direction using Refri*Master manual cutter. The hand-held hose cutter is especially designed for cutting non-wire reinforced hose, SAE J2064 Type E refrigerant hose. Be sure the cut is made square to the hose length.

HOSE, CLAMPS, CUTTER, and PLIERS

Refri*masterplus CLAMPS and PLIERS

Fittings — mANULI / FRIGOCLIC® Section V: Illustrated

with holes w/o holes


Section V: Illustrated FRIGOCLIC® / mANULI — Fittings

FEMALE O’RINGSTRAIGHT w/Port

R134a, High Side08-6031Q #6 #6 5/8 -18 16mm08-6032Q #8 #8 3/4 -16 16mm

R134a, Low Side08-6033Q #10 #10 7/8 -14 13mm08-6037Q #10 #12 7/8 -14 13mm.

FITTING HOSE THREAD PART # END END SIZE PORT

FEMALE O’RINGSTRAIGHT

08-6061Q #6 #6 5/8 -18 w/o port08-6071Q #6 #8 5/8 -18 w/o port08-6062Q #8 #8 3/4 -16 w/o port08-6072Q #8 #10 3/4 -16 w/o port08-6063Q #10 #10 7/8 -14 w/o port08-6074Q #10 #12 7/8 -14 w/o port08-6064Q #12 #12 1-1/16 -14 w/o port.


FEMALE O’RING 90° ELBOW w/Port

R134a, High Side08-6931Q #6 #6 5/8 -18 16mm08-6932Q #8 #8 3/4 -16 16mm08-6935Q #8 #10 3/4 -16 16mm

R134a, Low Side08-6933Q #10 #10 7/8 -14 13mm08-6937Q #10 #12 7/8 -14 13mm.


08-6461Q #6 #6 5/8 -18 w/o port08-6462Q #8 #8 3/4 -16 w/o port08-6472Q #8 #10 3/4 -16 w/o port08-6463Q #10 #10 7/8 -14 w/o port08-6474Q #10 #12 7/8 -14 w/o port08-6464Q #12 #12 1-1/16 -14 w/o port.

FEMALE O’RING45° ELBOW


FEMALE O’RING45° ELBOW w/Port

R134a, High Side08-6432Q #8 #8 3/4 -16 16mm

R134a, Low Side08-6433Q #10 #10 7/8 -14 13mm.


FEMALE O’RING90° ELBOW

08-6961Q #6 #6 5/8 -18 w/o port08-6975Q #6 #8 5/8 -18 w/o port08-6962Q #8 #8 3/4 -16 w/o port08-6973Q #8 #10 3/4 -16 w/o port08-6963Q #10 #10 7/8 -14 w/o port08-6974Q #10 #12 7/8 -14 w/o port08-6964Q #12 #12 1-1/16 -14 w/o port.


NOTE • Fittings not supplied with clamps!


MALE O’RINGSTRAIGHT

08-5061Q #6 #6 5/8 -18 w/o port08-5071Q #6 #8 3/4 -18 w/o port08-5063Q #10 #10 7/8 -18 w/o port08-5074Q #10 #12 7/8 -18 w/o port08-5064Q #12 #12 1-1/16 -16 w/o port.


08-5465Q #6 #8 5/8 -18 w/o port08-5467Q #10 #12 1-1/16 -16 w/o port

.

MALE O’RING45° ELBOW


08-5051Q #6 #6 5/8 -18 w/o port.

MALE INSERT O’RINGSTRAIGHT


MALE INSERT O’RING90° ELBOW

08-5955Q #6 #8 5/8 -18 w/o port08-5956Q #8 #10 3/4 -16 w/o port.


MALE O’RING90° ELBOW

08-5961Q #6 #6 5/8 -18 w/o port08-5971Q #6 #8 5/8 -18 w/o port08-5963Q #10 #10 7/8 -18 w/o port08-5974Q #10 #12 7/8 -18 w/o port08-5964Q #12 #12 1-1/16 -16 w/o port.

FITTING HOSE THREAD PART # END END SIZE PORTRefri*masterplus

SAE J2064 Type EHOSE and CUTTER

Refri*masterplus CLAMPS and PLIERS

09-1028Q #6 clamp 09-1016Q09-1029Q #8 clamp 09-1017Q09-1030Q #10 clamp 09-1018Q09-1031Q #12 clamp 09-1019Q

15-3243 CLIC PLIERS

for BLACK HOSE HOSE END for GREY HOSE PART # CLAMP PART #

BLACK HOSE HOSE HOSE PART# END LENGTH09-7036 #6 70 ft09-7038 #8 75 ft09-7040 #10 75 ft09-7042 #12 60 ft

15-3265 HOSE CUTTER

IMPORTANT: There are two (2) types of Manuli hose used with clip-on fittings black and grey. We do not supply the grey colored hose. The black hose will replace the grey hose, but only if used with the correct style clamp & cage assy. (the clamps are different O.D.)

For black hose use clamp & cage assembly numbers 09-1028Q through 09-1031Q (these have 2 small holes drilled in the bar)

For grey hose connections, use 09-1016Q through 09-1019Q (these do not have the holes in the bar)

For the above reasons, all Manuli fittings are supplied without the clamp & cage assy. You must order the correct ones required per type of hose used.

TECHTIP

with holes w/o holes




Section V: Illustrated FRIGOCLIC® / mANULI — Fittings

R1208-3021Q #6 #6 1/4”08-3022Q #8 #8 1/4”08-3023Q #10 #10 1/4”08-3024Q #12 #12 1/4”

R134a, High Side 16mm08-3421Q #6 #6 16mm08-3422Q #8 #8 16mm08-3429Q #10 #10 16mm

R134a, Low Side 13mm08-3423Q #10 #10 13mm08-3424Q #12 #12 13mm.

SPLICER STRAIGHT w/Port

HOSE HOSE PART # END END PORT

SPLICERS90° ELBOW

08-3026Q #8 #8 w/o port08-3027Q #10 #10 w/o port08-3028Q #12 #12 w/o port.


SPLICERS STRAIGHT

08-3000Q #6 #6 w/o port08-3001Q #8 #8 w/o port08-3002Q #10 #10 w/o port08-3003Q #12 #12 w/o port.


SPLICERS - TEE STYLE3 Way

08-3018Q #8 #8 #8 w/o port08-3019Q #10 #10 #10 w/o port08-3020Q #12 #12 #12 w/o port.

HOSE HOSE HOSE PART # END END END PORT

SPLICERS“Y” CONNECTION

08-3438Q #8 #8 #8 w/o port08-3439Q #12 #12 #12 w/o port.


SPLICERS“H” CONNECTION

08-3435Q #8 #8 #8 w/o port08-3436Q #12 #12 #12 w/o port08-3437Q #12 #12 #10 w/o port.





Carrier Number Truck Air No. Description Manuli Number Truck Air No. Description

40-60050-02 .................... 08-6461Q .......................Female O-ring40-60050-03 .................... 08-6462Q .......................Female O-ring40-60050-04 .................... 08-6463Q .......................Female O-ring40-60050-05 .................... 08-6464Q .......................Female O-ring40-60050-06 .................... 08-6472Q .......................Female O-ring40-60051-02 .................... 08-5061Q ...........................Male O-ring40-60051-04 .................... 08-5063Q ...........................Male O-ring40-60051-07 .................... 08-5074Q ...........................Male O-ring40-60058-04 .................... 08-3423Q ...................................Splicer40-60058-05 .................... 08-3424Q ...................................Splicer40-60059-03 .................... 08-3422Q ...................................Splicer40-60059-04 .................... 08-3429Q ...................................Splicer40-60060-02 .................... 08-6061Q .......................Female O-ring40-60060-03 .................... 08-6062Q .......................Female O-ring40-60060-04 .................... 08-6063Q .......................Female O-ring40-60060-05 .................... 08-6064Q .......................Female O-ring40-60060-06 .................... 08-6072Q .......................Female O-ring40-60060-07 .................... 08-6074Q .......................Female O-ring40-60060-08 .................... 08-6071Q .......................Female O-ring40-60061-02 .................... 08-6961Q .......................Female O-ring40-60061-03 .................... 08-6962Q .......................Female O-ring40-60061-04 .................... 08-6963Q .......................Female O-ring40-60061-05 .................... 08-6964Q .......................Female O-ring40-60061-06 .................... 08-6973Q .......................Female O-ring40-60061-07 .................... 08-6974Q .......................Female O-ring40-60061-08 .................... 08-6975Q .......................Female O-ring40-60081-03 .................... 08-3022Q ...................................Splicer40-60081-04 .................... 08-3023Q ...................................Splicer40-60081-05 .................... 08-3024Q ...................................Splicer40-60083-02 .................... 08-5961Q ...........................Male O-ring40-60083-04 .................... 08-5963Q ...........................Male O-ring40-60083-07 .................... 08-5974Q ...........................Male O-ring40-60083-08 .................... 08-5971Q ...........................Male O-ring40-60086-03 .................... 08-3001Q ...................................Splicer40-60086-04 .................... 08-3002Q ...................................Splicer40-60086-05 .................... 08-3003Q ...................................Splicer40-60137-03 .................... 08-3026Q ...................................Splicer40-60137-04 .................... 08-3027Q ...................................Splicer40-60137-05 .................... 08-3028Q ...................................Splicer40-62012-00 .................... 08-3018Q ...................................Splicer40-62012-01 .................... 08-3020Q ...................................Splicer40-62012-02 .................... 08-3019Q ...................................Splicer40-62022-00 .................... 08-6935Q .......................Female O-ring40-62022-01 .................... 08-6932Q .......................Female O-ring40-62023-00 .................... 08-6937Q .......................Female O-ring40-62023-01 .................... 08-6933Q .......................Female O-ring

Manuli Number Truck Air No. DescriptionC30010-06-06 ................. 08-3000Q ...................................SplicerC30010-08-08 ................. 08-3001Q ...................................SplicerC30010-10-10 ................. 08-3002Q ...................................SplicerC30010-12-12 ................. 08-3003Q ...................................SplicerC30012-06-06 ................. 08-3021Q ...................................SplicerC30012-08-08 ................. 08-3022Q ...................................SplicerC30012-10-10 ................. 08-3023Q ...................................SplicerC30012-12-12 ................. 08-3024Q ...................................SplicerC30015-06-06 ................. 08-3421Q ...................................SplicerC30015-08-08 ................. 08-3422Q ...................................SplicerC30015-10-10 ................. 08-3429Q ...................................SplicerC30016-10-10 ................. 08-3423Q ...................................SplicerC30016-12-12 ................. 08-3424Q ...................................SplicerC30090-08-08 ................. 08-3026Q ...................................SplicerC30090-10-10 ................. 08-3027Q ...................................SplicerC30090-12-12 ................. 08-3028Q ...................................Splicer

C300H0-08-08-08 ........... 08-3435Q ...................................SplicerC300H0-12-12-12 ........... 08-3436Q ...................................SplicerC300H0-12-12-10 ........... 08-3437Q ...................................SplicerC300T0-08-08-08 ............ 08-3018Q ...................................SplicerC300T0-10-10-10 ............ 08-3019Q ...................................SplicerC300T0-12-12-12 ............ 08-3020Q ...................................SplicerC300Y0-08-08-08 ............ 08-3438Q ...................................SplicerC300Y0-12-12-12 ............ 08-3439Q ...................................SplicerC37910-06-06 ................. 08-5051Q .................Male Insert O-ringC37990-08-06 ................. 08-5955Q .................Male Insert O-ringC37990-10-08 ................. 08-5956Q .................Male Insert O-ringC38010-06-06 ................. 08-5061Q ...........................Male O-ringC38010-08-06 ................. 08-5071Q ...........................Male O-ringC38010-10-10 ................. 08-5063Q ...........................Male O-ringC38010-12-10 ................. 08-5074Q ...........................Male O-ringC38010-12-12 ................. 08-5064Q ...........................Male O-ringC38040-08-06 ................. 08-5465Q ...........................Male O-ringC38040-12-10 ................. 08-5467Q ...........................Male O-ringC38090-06-06 ................. 08-5961Q ...........................Male O-ringC38090-08-06 ................. 08-5971Q ...........................Male O-ringC38090-10-10 ................. 08-5963Q ...........................Male O-ringC38090-12-10 ................. 08-5974Q ...........................Male O-ringC38090-12-12 ................. 08-5964Q ...........................Male O-ringC47910-06-06 ................. 08-6061Q .......................Female O-ringC47910-08-06 ................. 08-6071Q .......................Female O-ringC47910-08-08105 ........... 08-6062Q .......................Female O-ringC47910-10-08103 ........... 08-6072Q .......................Female O-ringC47910-10-10 ................. 08-6063Q .......................Female O-ringC47910-12-10 ................. 08-6074Q .......................Female O-ringC47910-12-12 ................. 08-6064Q .......................Female O-ringC47915-06-06 ................. 08-6031Q .......................Female O-ringC47915-08-08 ................. 08-6032Q .......................Female O-ringC47916-10-10 ................. 08-6033Q .......................Female O-ringC47916-12-10 ................. 08-6037Q .......................Female O-ringC47940-06-06 ................. 08-6461Q .......................Female O-ringC47940-08-08 ................. 08-6462Q .......................Female O-ringC47940-10-08 ................. 08-6472Q .......................Female O-ringC47940-10-10 ................. 08-6463Q .......................Female O-ringC47940-12-10 ................. 08-6474Q .......................Female O-ringC47940-12-12 ................. 08-6464Q .......................Female O-ringC47945-08-08 ................. 08-6432Q .......................Female O-ringC47946-10-10 ................. 08-6433Q .......................Female O-ringC47990-06-06 ................. 08-6961Q .......................Female O-ringC47990-08-06 ................. 08-6975Q .......................Female O-ringC47990-08-08037 ........... 08-6962Q .......................Female O-ringC47990-10-08 ................. 08-6973Q .......................Female O-ringC47990-10-10 ................. 08-6963Q .......................Female O-ringC47990-12-10 ................. 08-6974Q .......................Female O-ringC47990-12-12 ................. 08-6964Q .......................Female O-ringC47995-06-06 ................. 08-6931Q .......................Female O-ringC47995-08-08 ................. 08-6932Q .......................Female O-ringC47995-10-08 ................. 08-6935Q .......................Female O-ringC47996-10-10 ................. 08-6933Q .......................Female O-ringC47996-12-10 ................. 08-6937Q .......................Female O-ringRPMclamp-06.................. 09-1028Q Hose/Refri Master Plus ClampRPMclamp-08.................. 09-1029Q Hose/Refri Master Plus ClampRPMclamp-10.................. 09-1030Q Hose/Refri Master Plus ClampRPMclamp-12.................. 09-1031Q Hose/Refri Master Plus ClampRefriMaster Plus-06......... 09-7036 ............Hose/Refri Master PlusRefriMaster Plus-08......... 09-7038 ............Hose/Refri Master PlusRefriMaster Plus-10......... 09-7040 ............Hose/Refri Master PlusRefriMaster Plus-12......... 09-7042 ............Hose/Refri Master PlusCLIC Pliers ...................... 15-3243 ...............................CLIC PliersRefri-Cutter ...................... 15-3265 ......................Hose Cutter Tool

INTERChANGE


ALL REQUIRED SEALING WASHERS and O-RINGS are SUPPLIED with FITTING. (Listed in ascending order by part number.)

FREIGHTLINER

• example 1 Compressor with OE hose assy

• example 2Condenser with OE hose

Slimline MIO08-0602S ....#6 .......... #6Evaporator/TXV (Liquid)

Slimline MIO08-0603S ....#8 .......... #8Compressor (Discharge)fits GH head

Slimline MIO08-0604S ....#8 .......... #8Condenser (Discharge)

Slimline MIO08-0600S ....#6 .......... #6Condenser/Drier (Liquid)

Slimline MIO08-0601S ....#6 .......... #6Drier (Liquid)

#6 Slot #10 Slot #10 Slot for #08-0605S

#6 Slot for #08-0600S

Slimline MIO08-0605S ....#10 ...... #10Compressor (Suction) for GH head

Slimline MIO08-0606S ....#10 ...... #10Evaporator TXV (Suction)

Slimline MIO08-0611S ....#10 ...... #10Pad Manifold Adapter Ftg.fits exp vlv #12-0617A

#6 Slot for #08-0600S

(fits into slot)

(fits into slot #08-0603S)

REpAIR OR REpLACE ANy OE hOSE WITh pAD CONNECTIONS!NO WELDING REQUIRED!

Now you can make up your own hose assemblies using our exclusive line of field repair fitting adapters for all makes of heavy duty trucks - Freightliner, Kenworth, Navistar, Peterbilt & Volvo.

See the examples below. Photos are of actual OE components on a late model Volvo VN truck. The same concept applies to all other makes of trucks. Allows the mechanic the option to make up hoses with ordinary beadlock or EZ-clip fittings, using choice of Goodyear/Parker/EX-clip hose in either standard or reduced diameter size.

Compressor w/field repair hoses(using #08-1602S & #08-1603S adapters)

Condenser w/field repair hose(using #08-1601S adapter)

#6 Slot for #08-0600S

Section V: Illustrated pAD mANIFOLD (Field Repair) — Fittings


ALL REQUIRED SEALING WASHERS and O-RINGS are SUPPLIED with FITTING. (Listed in ascending order by part number.)

KENWORTH / PETERBILT

PETERBILT with Reduced Diameter Hose Connections

INTERNATIONAL - NAVISTAR

VOLVO / MACK with WV Head

Pad/Tube MIO08-1002S ....#8 .......... #8Condenser (Discharge)

Pad/Tube MIO08-1000S ....#6 .......... #6Drier (Inlet)

Hose Ftg.08-1003A ....#8 .......... #8Discharge Ftg. 45°

Hose Ftg.08-1003B ....#8 .......... #8Discharge Ftg. 90° (short)

Hose Ftg.08-1003C ....#8 .......... #8Discharge Ftg. 90° (long)

Pad/Tube MIO08-1001S ....#6 .......... #6Condenser (Liquid)

Pad/Tube MIO08-1003S ....#8 .......... #8Compressor (Discharge)

Pad/Tube MIO08-1004S ....#10 ...... #1008-1005S ....#10 ...... #12Compressor (Suction)

Pad/Tube MIO08-1601S ....#8 .......... #6Condenser (Liquid)

Pad/Tube MIO08-1603S ....#10 ...... #10Compressor (Suction)

Pad/Tube MIO08-0802S ....#8 .......... #8Comp / Cond (Discharge)

Pad/Tube MIO08-0801S ....#8 .......... #6Cond / Evap (Liquid)

Pad/Tube MIO08-0803S ....#10 ...... #10Comp / Cond / Evap / Accumulator (Suction)

Pad/Tube MIO08-1604S ....#10 ...... #12Compressor (Suction)

Pad/Tube MIO08-1602S ....#8 .......... #8Condenser, Compressor (Discharge)

#10 Slot for #08-1004S#08-1005S

(fits into slot #08-1003S)

Fittings — pAD mANIFOLD (Field Repair) Section V: Illustrated

Pad/Tube MIO08-0804S ....#10 ...... #12Comp / Cond / Evap / Accumulator (Suction)


CATerpillAr / kOMATsu ............................ #6 MiO .......................08-3201SCAT drier #07-5057A (outlet sides)komatsu drier #07-5054A

VOlVO OFFrOAD ........................................... #6MiO ........................08-3203Sfits drier #07-5072A (inlet and outlet sides)

J.Deere .......................................................... #6 MiO .......................08-3200Sfits drier #07-5070A (outlet side)

CATerpillAr ................................................. #6 MiO .......................08-3202Sfits drier #07-5055A (outlet side)

CATerpillAr ................................................. #6 MiO .......................08-3205Sfits #07-5055A (inlet side)

J.Deere, CAT, kOMATsu ............................. #6 MiO .......................08-3204SJ.Deere drier #07-5070A (inlet sides)komatsu drier #07-5054ACAT drier #07-5057A

pAD TypE DRIER FIELD REpAIR FITTINGS

PARTAPPlIcATION NO.

PARTAPPlIcATION NO.

Section V: Illustrated pAD TypE (Field Repair) — Fittings

OEM Field Repair

example: All fittings are universal standard thread 5/16” #6 Male Insert O-ring connectionsEnables installer to attach field made hose assys.


gM/FOrD MeTriC r134a M12-1.5 16MM 08-8438priMArY serViCe pOrT

MAle THreAD - MeTriC - High side

DEScRIPTION THREAD PORT PART SIZE SIZE NO.

ADAPTER TYPE THREAD PORT PART SIZE SIZE NO.

welD-ON reTrOFiT pOrTs NONe 13MM 08-8313 1 NONe 13MM 08-8313S 2 NONe 16MM 08-8316S 2

1 Aluminum2 steel

FOrD and NAVisTAr r134a M10-1.25 13MM 08-8437 1priMArY seAl pOrT Female

1 low side (suction)

RETROFIT ADApTER FITTINGS (R134a)

90 Degree (uNiVersAl) - sTeel 3/16” (High) 16MM 08-8490wiTH sHrADer COre 1/4” (low) 13MM 08-8491wiTH THreAD lOCk 1/4” (High) 16MM 08-8492

High side (discharge)

sTrAigHT (uNiVersAl) - sTeel 3/16” (High) 16MM 08-8400wiTH sHrADer COre 1/4” (low) 13MM 08-8401*wiTH THreAD lOCk 1/4” (High) 16MM 08-8402*

High side (discharge)low side (suction)

gM priMArY r134a 1/4” 16MM 08-8412HigH siDe ADApTer pOrT (For retrofitting r12 2-piece primary seal port)

THreAD sTD 1/4” (7/16-20)


gM/CHrYsler/Jeep OeM M15-1.0 (High16MM) 08-8432 1HigH-FlOw reTrOFiT pOrTs (Non-replaceable shrader cores) M15-1.0 (High16MM) 08-8436 2 M13-1.0 (low13MM) 08-8435 2

MAle THreAD - MeTriC


1 Aluminum2 steel

* Available in 10-pack. Order with suffix “-10”

AerOQuip 90 Degree 3/16 (A) M10 (b) 08-8920HigH siDe Tee

FeMAle (A) x MAle swiTCH pOrT (b) x 16MM r134a pOrT (C)

B

C

A

To be Discontinued upon depletion of stock.

For adding switch port to high side

Fittings — RETROFIT ADApTERS Section V: Illustrated


1. Determine compressor head type (see Diagram A) (Tube-O, rotolock, #8 - #10 O-ring, or Flange).2. Determine type of refrigerant used in system (r12 or r134a).3. Determine choice of type of service valve (standard or back seat type and/or beadlock Hose end) (see Diagram b).

SERVICE VALVES – ORDERING INFORmATION

Compressor head Types - Diagram A

Vertical Tube “O” Type

Types Of Service Valves - Diagram b

(1) Back seat type valves contain a manually operated valve which controls the position of the service valve, either allowing full refrigerant flow, a mid-way test/flow, or totally blocked off refrigerant flow from the rest of the A/C system. The standard type service valve can be substituted but allows only constant full refrigerant flow.

Standing FittingType

Back Seat FittingType (1)

Standard BeadlockCrimp Type

Vertical O-Ring TypeHorizontal O-Ring

(o-ring type shown)

Section V: Illustrated SERVICE VALVES — Fittings

TypICAL SANDEN / SELTEC REAR hEAD TypES

(shown with R134a ports)


cOMPRESSOR TYPE cOMP. HOSE PART FTG. FTG. NO.


SERVICE VALVES–R12 / with ROTOLOCk STyLE COmpRESSOR

YOrk, T/CCi, TeCuMseH DisCH .............. 8 ...............08-3139 suCT ............ 10 ...............08-3140



SERVICE VALVES – R12 / with TUbE-O TypE COmpRESSOR

YOrk, T/CCi, TeCuMseH suCT ............ 10 ...............08-3350

YOrk, T/CCi, TeCuMseH DisCH .............. 8 ...............08-3051B suCT ............ 10 ...............08-3052B

MAle iNserT O-riNg (bACk seAT TYpe VAlVe)

beADlOCk FlAre (bACk seAT TYpe VAlVe)

MAle iNserT 0-riNg

YOrk, T/CCi, TeCuMseH suCT ............ 10 ...............08-3250

YOrk, T/CCi, TeCuMseH DisCH .............. 8 ...............08-3053wiTH reAr pOrT suCT ............ 10 ...............08-3054

MAle iNserT 0-riNg (MiO)

r12

r12

r12

r12

YOrk, T/CCi, TeCuMseH suCT ............ 12 ...............08-3143B

beADlOCk

r12

r12

YOrk, T/CCi, TeCuMseH DisCH .............. 8 ...............08-3151bACk seAT TYpe VAlVe

YOrk, T/CCi, TeCuMseH suCT ............ 10 ...............08-3152bACk seAT TYpe VAlVe

MAle iNserT O-riNg (MiO)MAle iNserT O-riNg (MiO)

r12r12

Fittings — SERVICE VALVES Section V: Illustrated



r12



SERVICE VALVES – R12 / with TUbE-O TypE COmpRESSORS



YOrk, T/CCi, TeCuMseH, DisCH .............. 8 ...............08-3155sANDeN suCT ............ 10 ...............08-3156(wiTH (2)serViCe pOrTs)

YOrk, T/CCi, TeCuMseH, DisCH .............. 8 ...............08-3370sANDeN suCT ............ 10 ...............08-3371(wiTHOuT serViCe pOrT)

SERVICE VALVES – with VERTICAL/hORIzONTAL O-RING COmpRESSORS

sANDeN/Diesel-kiki DisCH .............. 8 ...............08-3359(wiTH r12 pOrT) suCT ............ 10 ...............08-3360

O-riNg

MAle iNserT O-riNg (MiO) MAle iNserT O-riNg (MiO)

r1208-3362 #8-3/4” -16 Female x 3/4” -16 Male08-3363 #10-7/8” -14 Female x 7/8” -14 Male

Sanden, Seltec/Valeo, ICE90° O’Ring Coupler

Adapts to Male Insert O’Ring

(continued)

r12

cOMPRESSOR TYPE PAD/TUBE MIO PART FTG. FTG. NO.

DeNsO pAD FiTTiNg #8 ...................... #8 ...............08-349810pA15C #10 .................... #10 ...............08-3499(fits onto plate of #03-3167)

DeNsO pAD FiTTiNg Discharge ...................... #8 ...............08-350710s15C suction .................... #10 ...............08-3508(fits onto plate of #03-3179)

SERVICE VALVES – DENSO

AluMiNuM

16-4151#8 O-ringDischarge

16-4152#10 O-ringSuction

16-4305#8 O-ringDischarge

16-4304#10 O-ringSuction

Std O-ring

Std O-ring

(wiTHOuT pOrT)

08-337510pA17C Top - Discharge and suction (w/oil bypass) #8, #10 MiO ftgs.

08-33766e171 (J.Deere)#10 suction Manifold,r12 port , 7/16” thread

08-33776e171 (J.Deere) #8 Discharge Manifold M12-1.00 thread , HprV


gM A6 - pAD ADApTer FiTTiNgs #8 ...........................08-3045S #10 .........................08-3046S #12 .........................08-3047S

cOMPRESSOR TYPE cOMP. HOSE PORT PART FTG. FTG. SIZE NO.


#16-4224 O-riNgsuCT/DisCH

cOMPRESSOR TYPE cOMP. PART FTG. NO.

CATerpillAr A6 Compressor #8 w/16mm port .........08-3090serViCe VAlVe FiTTiNg (steel) #10 w/13mm port .........08-3091r134a pOrT

SERVICE VALVES – Gm A6 / S6 COmpRESSORS

#16-4224 O-riNgsuCT/DisCH

08-3048S gM A6 HOlD DOwN brACkeT(supplied w/standard and metric bolt)

cOMPRESSOR TYPE cOMP. PART FTG. NO.

SERVICE VALVES – R134a – w/SANDEN / SELTEC / I.C.E. VERTICAL O-RING TypE COmpRESSOR

sANDeN/selTeC DisCH ........ 8x8 ...... 16MM ........08-3489sTD. FlOw pOrTs suCT .... 10x10 ...... 13MM ........08-3490

MAle iNserT O-riNg No. 8 and No. 10 Fittings (Not for rotolock or Tube-O type)

USE TO ADD A SERVICE PORT TO SANDEN/SELTEC R134a COMPRESSORS.

sANDeN/selTeC DisCH ........ 8x8 .... 16MM ........08-8038 suCT .... 10x10 .... 13MM ........08-8040low side

High side

TECHTIP


SELTEC Tm31 Only

SELTEC TM31HD DISCH .... 10 ......16MM .....08-3372STD. FLOW PORTS (16mm port only .....08-8414)

SUCT .... 12 ......13MM .....08-3373 (13mm port only .....08-8413)

lo side

Hi side

08-337308-3372

08-8413

08-8414

(uses #16-4153 o’ring)


sTep MANiFOlD FiTTiNg ......................... #10 x #8 .............................08-3626Aluminum

#8

DeepiNserT

#10

Also see: #03-6518, #03-6519universal swivel Manifold Fittings

NOTE Also, see page 300 for additional A6 / s6 compatible manifolds.



SERVICE VALVES – R134a / for FLANGE TypE COmpRESSOR


T/CCi (York style) TeCuMseH suCT .....10...... 13MM ......08-3486sTD. FlOw pOrTs

MAle iNserT O-riNg


SERVICE VALVES – R134a / for ROTOLOCk STyLE COmpRESSOR

SERVICE VALVES – R134a / for TUbE-O TypE COmpRESSOR

T/CCi (York style) TeCuMseH DisCH ........8 ...... 16MM ........08-3476BsTD. FlOw pOrTs suCT ......10 ...... 13MM ........08-3477B suCT ......12 ...... 13MM ........08-3497B




pusH-ON beADlOCk

MAle iNserT O-riNg

T/CCi (York style) TeCuMseH DisCH ........8 ...... 16MM ........08-3478BsTD. FlOw pOrTs suCT ......10 ...... 13MM ........08-3479B suCT ......12 ...... 13MM ........08-3480B

For reduced Diameter Hose

DisCH ........ 8 .....................08-3478BR suCT ....... 10 ....................08-3479BR suCT ....... 12 ....................08-3480BR suCT ....... 14 ....................08-3495BRpusH-ON beADlOCk MAle iNserT O-riNg

MAle iNserT O-riNg (bACk seAT TYpe VAlVe)

* High Flow ports

T/CCi (York style) TeCuMseH DisCH .........8.......16MM ...... 08-3483HigH FlOw pOrTs suCT .......10.......13MM ...... 08-3484 suCT .......10.......13MM ...... 08-3484H*

T/CCi (York style) TeCuMseH DisCH .......8.......16MM ....... 08-3481HigH FlOw pOrTs suCT .....10.......13MM ....... 08-3482

* High Flow ports

T/CCi (York style) TeCuMseH DisCH ........8 ...... 16MM ...... 08-3491or sANDeN Tube-O DisCH ........8 ...... 16MM ...... 08-3491H*HigH FlOw pOrTs suCT ......10 ...... 13MM ...... 08-3492 suCT ......10 ...... 13MM ...... 08-3492H*

T/CCi (York style) TeCuMseH DisCH ........8 ...... 16MM ...... 08-3493HigH FlOw pOrTs suCT ......10 ...... 13MM ...... 08-3494

Tube-O riNg COMpressOrserViCe VAlVe DisCH ........8 .........................08-3378steel beadlock w/o port suCT ......10 .........................08-3379

For reduced Diameter Hose

suCT ....... 14 ....................08-3385BR

MAle iNserT O-riNg (bACk seAT TYpe VAlVe)beADlOCk


SUCTION / DISChARGE TEE FITTINGS

suCTiON Tee FiTTiNg #12 MOr (male o’ring) .................08-7690 (Ford e series suction Tee) #12 FiOr (female insert o’ring) #10 MiO (male insert o’ring)

DEScRIPTION FTG. SIZE PART NO.DEScRIPTION FTG. SIZE PART NO.

#10

#12

suCTiON Tee FiTTiNg #12 MiO (male insert o’ring) .........08-8135(Carrier system 40-62019-02) #12 FiOr (female insert o’ring) #12 MiO (male insert o’ring)

#12 #12

#12

#12

suCTiON Tee FiTTiNg #12 MOr (male o’ring) .................08-8134(Carrier #40-62019-03) #12 FiOr (female insert o’ring) #10 MiO (male insert o’ring)

#12

#10

#12

suCTiON Tee FiTTiNg #12 MOr (male o’ring) .................08-7693(Ford e series suction Tee) #12 FiOr (female insert o’ring) #12 MiO (male insert o’ring)

#12

#12

suCTiON Tee FiTTiNg Flange .........................................08-7698proAir A/C #10 MiO (male insert o’ring)with side Connection #16-4294 gasket kit

uses gaskets#16-4292

#10

suCTiON Tee FiTTiNg Flange ..........................................08-7699(Carrier #40-62091-00) #10 MiO (male insert o’ring) #16-4294 gasket kit

suCTiON Tee FiTTiNg #27mm FOr ............................. 08-8137M #27mm MiO #10 MiO

MAle iNserT O-riNg Tee 6x6x6 MiO ......................08-5676blOCk FiTTiNg 10x10x10 MiO ...................08-5677


#10

#16-4294

Photo Not Available


#6 MiO


notE: If used with steel fittings, use of an anti-sieze compound is recommended.

Tee blOCk 6x6x6 ........... 08-8130FeMAle iNserT O-riNg FiTTiNgs 10x10x10 ........... 08-8131(aluminum)

DEScRIPTION FTG. SIZE PART NO. DEScRIPTION FTG. SIZE PART NO.

TEE bL0CkS and FITTINGS for DUAL A/C SySTEmS

Tee blOCk FiTTiNgs w/swiVel NuT 6x6x6 ........... 08-8132MAle iNserT O-riNg x FeMAle iNs. 10x10x10 ........... 08-8133O-riNg x MAle O-riNg (aluminum)

1 #6 Hose

#8 FeMAle x #8 MiO x #6 beADlOCk HOse Tee 8x8x6 ..........08-5667BS 1

#6 bl

#8 MiO#8

3/4” iD HOse spliCer ................................................................... 08-7700BR#14 x #14 x #10 MiOreduced beadlock

#10 MiO

#14

#14

DEScRIPTION FTG. SIZE PART NO. DEScRIPTION PART NO.

MiO

DisCHArge Tee FiTTiNg #6 MiO x #6 MiO x #6 FiOr .........08-8138 #8 MiO x #8 MiO x #8 FiOr .........08-8139

MiO

FiOr

SUCTION / DISChARGE TEE FITTINGS (continued)

ADApTer FiTTiNg ................................... 08-7694spriNTer 6 x 6 pADsAluminum

suCTiON Tube ........................................ 08-7695spriNTer10 x 10 pADsAluminum


“SpECIALTy” ADApTER / mANIFOLD FITTINGS PARTAPPlIcATION NO.

PARTAPPlIcATION NO.

PARTAPPlIcATION NO.

ADApTer FiTTiNg ................................... 08-76946 x 6 pADsAluminum

suCTiON Tube ........................................ 08-7695spriNTer10 x 10 pADsAluminum

ADApTer FiTTiNg ................................... 08-3502#8 MiOAluminum

MANiFOlD FiTTiNg .............................. 08-3501S#8 MiO

sTep MANiFOlD FiTTiNg ....................... 08-3626#8 x #10Aluminum

MANiFOlD FiTTiNg .............................. 08-3500S#6 MiO

MANiFOlD FiTTiNg ................................. 08-3524FOrD F-series AuX. A/C#6 MiO Aluminum

ADApTer FiTTiNg ................................... 08-3504#8 pad x #6MiOAluminum

spliCer ADApTer blOCk .................... 08-3530useD FOr AuX. A/C#10 MiO Aluminum

ADApTer FiTTiNg ................................... 08-3505#8 pAD x #8 MiOAluminum

spliCer ADApTer blOCk ................. 08-3530LuseD FOr AuX. A/C#10 MiO Aluminum

ADApTer FiTTiNg ................................... 08-3522Aluminum

spliCer ADApTer blOCk .................08-3530RuseD FOr AuX. A/C#10 MiO Aluminum

ADApTer FiTTiNg ................................... 08-3523FOrD F-series AuX. A/C#10 MiO Aluminum

DisCHArge Tube ................................... 08-3610FOrD#8 MiOAluminum

COMpressOr MANiFOlD ..................... 08-3625ADApTer FiTTiNg #8 x #10Aluminum

#6 MiO

#8

DeepiNserT

#8

#10

#10

#10 MiO

#10 MiO

Fittings — SpECIALTy Section V: Illustrated

#10 MiO

#10 MiO

#8 MiO

#8 MiO

#8 MiO

#6 MiO

#6 MiO

#10 MiO

#8 MiO

#6 MiO

Only one (1) fitting supplied per part number. Photos show alternate view.

NOTE

fittings section v: illustrated fitting locater...

Documents