FINITE word length effectin fixed point processing

The Digital Signal Processors have finite width of the data bus.

The word-length after mathematical operations, if exceeds the bus width,

will have to be omitted.

This is the source of Serious Errors.

We now discuss attributes that cause such errors.

Causes of word length error

The different causes of the errors are:

Run time error or, Register Over-flow,

Arithmetic & coefficient truncation

Data scaling in an attempt to reduce overflow.

Zero-input limit cycling.

Fixed point design procedure

Ideal floating point

FloatingPoint To Fixed pt R

ealiz

able

Filt

er

Test &Evaluate

Fail !!! causes

OPTIONS

Pass: Luck

1.Register over flow2.Coefficient errors3. Arithmetic Errors.

1, adjust binary point2. Change architecture3.Scale Parameters

Run time / over flow error: Definition

The input data begins with sign bit followed by MSB to LSB extending to mantissa.

When the input data length is larger than the bus width, the sign bit followed by MSB bits etc. overflows the register on sign bit side.

Since the significant part is over-flown which causes the “remain” in the register useless.

Solution for Run time / over flow error:

For fixed point format, we should prefer the subtraction by of 2’s complement. Here the effect of overflow is least significant.Once the sign bit enters the overflow point of the accumulator and overflow likely detected, a Flag is activated that will clamp the input to the data bus by stopping less significant bits entering. Inaccuracy incurs due to loss of data after clamping.Clamping is saturation.

Scaling to reduce overflow..

hsm( )

h m( )

0

N 1

k

h2 k( )

=

• Here we scale the input to reduce its dynamic range. • It is at the cost of performance of the system.• The methods to scale are:

hsm( )

h m( )

0

N 1

k

h k( )

=

RMS scaling: preferred

Absolute scaling

Arithmetic truncation ErrorsWhen two inputs of length N are multiplied, the net word length can increase to 2N. 2N bit is rounding off to S(<2N) bits. These S bits are added with another S bits and the result is say, T bits.The contents are again rounded off to S bits and fed to accumulator.The output is truncated to M bits, the bus width.These multiple rounding-offs causes additive errors.If M<T< 2N, may cause an arithmetic error. Generally for N=16, 2x16 bit multiplication results in maximum 32 bits while the accumulator has a width of 40 bits.

Coefficient MULTIPLIER

N BIT COEFFICIENTSTORAGE REGISTER

Adder

INPUT xK

Output yk= Ayk-1+xk N bit Output

Storage register

yk-1

Ayk-1

Implementation of First Order Recursive Filter.

Multiply accumulate :MAC unit

N-bit i/p

N-bit i/p

2N bit r/o

to s bits S-bits

T- to S- bit r/o

S- to M-bit r/o output

S-bit Accumulator

r/o round offM bit bus

Coefficient QuantizationA transfer function is represented by a ratio of Numerator and Denominator polynomials.

The binary version of coefficients are not compatible with the data bus width. Requires quantization/truncation.

The coefficients of the denominator may be sensitive to instability.

Selecting suitable structures may reduce the sensitivity.

Limit Cycling

In IIR filters, even though the present input is zero, the output may reveal some undesirable variations due to past signal.

It is caused when the response of an unforced LTI system does not decays down to zero in stipulated time.

Larger the size of data bus, smaller is the effect of limit cycling.

Methods to control the errors:

Scale the input and/or coefficients.

Increase the word length and Select an alternative DSP

architecture.

Example:1 The binary version of filter coefficients after

arithmetical calculations can come out to be non-compatible with the length of data bus.

For a data bus of width n, the actual word length of data may be larger. We need to truncate it.

Example:

H(z) = 1/[1+az-1+b]

where a = -1.957 558 and b = 0.995 813.

Truncation contd:

• Let the bus width be n=8.

One bit for sign is dedicated.

Balance are 7 bits. • If the exponent a > 1;

here one bit for exponent has to be spared.• Balance are (n-2) =6 bits for mantissa. Round-

off of quantization coefficient is to be used. • For fixed point data processing:

Manipulation:

1. The result is added by 0.5, when ‘round-off’ is desired.

2. For bottom or floor, zero is added. 3. For top or ceiling 1.0 is added.

For fixed point data processing:

CASE-1

when the coefficient has an integer before decimal. a = -1.957 558

• This ‘a’ is multiplied by 2(n-2) = 64 to yield 125.283712.

• Add 0.5 for round-off: 125.783712

• We obtain its binary equivalent truncated to 8 bits including sign bit. This amounts to

10000011= -125.

Case-1…

• In practice, we need not convert it in binary.

• We take integer number and forgo mantissa.

• We now convert -125 back into the coefficient level by dividing by 26 = 64.

• The resulting quantized coefficient is

a~ = -125/64= -1.953125.

For fixed point data processing:CASE-2: when the coefficient is Mantissa. b=0.995 813.• This b is multiplied by (2n-1-1). Given b=0.995 813

multiplied by 27-1 = 127, the result = 126.468 251. • For round off add 0.5 : 126.96851.• 126.96851. when converted in binary and truncated,

becomes 0111 1110. It is 126 when taken in decimal.• The step is 126. This can be directly taken from

126.468251 by eliminating mantissa..• To reduce to coefficient size,126 is divided by 27=128. • The truncated coefficient b is 0.984375.

Final Solution and comments

• The quantized transfer function is:• H’(z) = 1/[1+a’z-1+b’] where a’ = -1.953 125

and b’ = 0,984375.• Check it for stability. • Try Matlab function: beq = a2dR(d,n) and beq = a2dT(d,n).• These function should generate the decimal

equivalent of the binary representation/decimal representation in sign-magnitude form of a decimal number with a specified number of bits for the fractional part obtained by rounding off.

Example:02 A Digital Signal Processor takes a word length of 7 bit and 1 sign bit. A set of coefficients have been calculated and tabulated as follows.

•

•Quantize the coefficients and find out the values the DSP will accepts in place of the calculated coefficients.

Filter Coefficients

value

ao = a8 0.7252 a1 = a7 -1.1111 a2 = a6 -0.5920 a3 = a5 3.1993 a4 5.5555

Soln:02• The number of bits excluding sign bit are 7.

• When treating integer + decimal, the total number of effective bits will be 6.

• When treating no integer and only decimal, the total number of effective bits will be 7.

• ADC being successive approximation, flooring scheme is applicable. Hence 0.5 is not added.

Soln_2….• 0.7252 x(27-1) = 92.1004 92:

92/128 = 0.71875• 1.1111x(26)= 71.1104 71:

71/64 = 1.1093751.0.5920X(27 -1) = 75.18475:

75/128=0.5859375• 3.1993x26 = 204.7552 204:

204/64 = 3.1875 • 5.5555x26= 355.5552 355:

355/64 = 5.546875

Results in Tabular Form

Filter Coefficients

value Quantized SAR

ao = a8 0.7252 0.71875

a1 = a7 -1.1111 -1.109375

a2 = a6 -0.5920 -0.5859375 a3 = a5 3.1993 3.1875 a4 5.5555 5.546875

Example:03

• A filter function is represented by the polynomial:

• H[z] = 1/ [1 + 1.19z-1 + 0.198 z-2].

• The poles are at 0.99 and 0.20. The system is unconditionally stable.

• The coefficients are quantized by a 6 bit uni-polar round-off quantizer. Whether the system remains stable?

Soln:03

(A)1.19: number of bits for effecting the unipolar bits are 6 that exclude sign bit. Hence 6 –1(integer)=5.

1.19x 25 =38.09 38: 38/25 = 1.1875.

(B)0.198: number of bits effecting the unipolar bits are 6 excluding the sign bit.

0.198x(26 -1)+0.5 =12.974 12/26 = 0.1875.• The TF becomes:

H~(z) = 1/(1+1.1875z-1+ 0.1875z-2 ]• TF is marginally stable as roots are[ 1, 0.1875]

Effect of quantization on performance

Problem:4

• A band-pass digital filter to be used for digital clock recovery at 4.8 kbaud and a sampling frequency of 153.6 kHz.

• The filter is characterized by

H(z) = 1/[1–1.957558z-1 + 0.995913 z-2].

• Assess the effect of 8 bit quantization on the (a) pole location of the filter and

(b) it’s center frequency.

Soln_4:Given that the TF is a normalized 2nd BPF.

The poles are therefore complex conjugate.

For the sake of simplicity we represent the

TF = 1/[1+az-1+bz-2]

Here a = -1.957558 and b = 0.995913.

Sampling frequency given is fs = 153.6 kHz.

The polar distance p of the pole (magnitude) from the origin =b and is calculated to be p = 0.99795.

Its angle with respect to positive x-axis: = cos-1{(-1.957558/2)/(0.99795)} = 11.25.

Thus the location of poles are 0.99795 11.25

Soln: 4….The least count per degree of the angle is

153.6 /360 = 0.426666 kHz.

The value of 11.25; the un-quantized center frequency is

11.25 x 0.426666 = 4.799999 kHz.

While quantization to 8 bits, 1 bit is sign bit. So the effective number of bits are 7 only.

The rule is:

effective bits will be 6 for integer + fractions,

for fraction, the effective bits will be 7.

Soln.4…..;Case 1 : Quantization of a =-1.957558. Keeping apart the sign, it contains an integer. Therefore 1.957558 x 26 = 125.283712 125

It’s quantized equivalent is 125/26 = 1.953125.

Case 2: Quantization of b = 0.995913.

It’s equivalent integer is 0.995913x(27-1) = 126.480951126

The resulting output is 126/27 = 0.984375.

Soln 4….. The new value of p =0.984375 = 0.992156 = cos-1{(-1.953125/(2 x 0.992156)} = 10.17 The LC per degree of the angle is 0.426666 kHz. The

new center frequency is

10.17 x 0.426666 = 4.3399 kHz. Location of quantized poles are 0.992156 10.17

status Location of poles Center frequency Unqunatized 0.99795 11.25 4.80 kHz quantized 0.992156 10.17

4.34 kHz