filters with internal seals - baldwin filters | home · refill engine with recommended motor oil....

BALDWINFILTER.COM Installation Instructions for BD7153, BD7154, BD7250 and BD50000 Heavy-Duty Lube Filters. When installing a heavy-duty lube filter, especially those used on vehicles in demanding, high pressure or high vibration environments, it is important to follow the recommended installation instructions. A properly installed filter will not only keep the oil flowing; it will also prevent leakage caused by the filter loosening or the gasket displacing. Gaskets help to seal the filter in place. The amount of additional turns needed to give the best gasket compression for that filter, is shown on the installation pictogram (see step 4). In addition to the gasket, some filters may also feature an internal seal, which seals the filter element to the post on the filter mounting base. The internal seal ensures a positive seal between the clean side and the dirty side of the filter element. When installing, it is important to remember to oil both the gasket and the internal seal (see step 2). Installation tips for these filters are as follows: 1. Clean base. Remove old filter and gasket. Wipe filter mounting base with clean cloth. 2. Apply clean oil to gasket and internal seal. Apply thin film of clean motor oil to new filter gasket and internal seal. Do not use grease. 3. Hand tighten to gasket contact. Position filter to engage the threads. Hand tighten until gasket contacts filter mounting base. 4. Tighten additional turns. Tighten an additional ¾ turn after gasket contact. Make sure gasket contacts filter mounting base before tightening additional ¾ turn. 5. No leaks. Refill engine with recommended motor oil. Start engine and check for leaks. Add oil if necessary. 6. Inspect for dents. Important – Do not use filter if it is dented. Note: A thin layer of clean motor oil must be applied to the gasket and internal seal before installing the filter. Applying oil to the internal seal will allow the internal seal to slide onto the post on the filter mounting base. TECH TIPS FILTERS WITH INTERNAL SEALS Gasket Internal Seal 3 5 6 4 1 2

Upload: trandien

Post on 09-Apr-2019

222 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: FILTERS WITH INTERNAL SEALS - Baldwin Filters | Home · Refill engine with recommended motor oil. Start engine and check for leaks. Add oil if necessary. 6. ... FILTERS WITH INTERNAL

BALDWINFILTER.COM

Installation Instructions for BD7153, BD7154, BD7250 and BD50000 Heavy-Duty Lube Filters.When installing a heavy-duty lube filter, especially those used on vehicles in demanding, high pressure or high vibration environments, it is important to follow the recommended installation instructions. A properly installed filter will not only keep the oil flowing; it will also prevent leakage caused by the filter loosening or the gasket displacing.

Gaskets help to seal the filter in place. The amount of additional turns needed to give the best gasket compression for that filter, is shown on the installation pictogram (see step 4).

In addition to the gasket, some filters may also feature an internal seal, which seals the filter element to the post on the filter mounting base. The internal seal ensures a positive seal between the clean side and the dirty side of the filter element. When installing, it is important to remember to oil both the gasket and the internal seal (see step 2).

Installation tips for these filters are as follows:

1. Clean base.Remove old filter and gasket. Wipe filter mountingbase with clean cloth.

2. Apply clean oil to gasket and internal seal.Apply thin film of clean motor oil to new filtergasket and internal seal. Do not use grease.

3. Hand tighten to gasket contact.Position filter to engage the threads. Hand tightenuntil gasket contacts filter mounting base.

4. Tighten additional turns.Tighten an additional ¾ turn after gasket contact.Make sure gasket contacts filter mounting basebefore tightening additional ¾ turn.

5. No leaks.Refill engine with recommended motor oil. Startengine and check for leaks. Add oil if necessary.

6. Inspect for dents.Important – Do not use filter if it is dented.

Note: A thin layer of clean motor oil must be applied to the gasket and internal seal before installing the filter. Applying oil to the internal seal will allow the internal seal to slide onto the post on the filter mounting base.

TECH TIPSFILTERS WITH INTERNAL SEALS

Gasket

InternalSeal

3 5 641 2

Internal combustion engine

internal combustion engine vs electric engine

Internal Combustion Engine. (I C Engine)

Internal Combution engine

Small Engine Discount · cv boot joint & axles chassis exhaust fenders & body fuel tanks internal engine hunting misc & safety oil filters oil & chemical rack & utilities tires &

Internal Combustion Engine Introduction Shoubra/Mechanical... · Internal Combustion Engine Introduction. The internal combustion (IC) engine is a heat engine that converts chemical

Principles of an Internal Combustion Engine...Principles of an Internal Combustion Engine Topics 1.0.0 Internal Combustion Engine 2.0.0 Engines Classification 3.0.0 Engine Measurements

Internal Combustion Engine (IC ENGINE)