fdkn-h - c-o-k.ru · 469 fdkn-h 12. wall mounted type packaged air-conditioner split system, air to...
TRANSCRIPT
469
FDKN-HFDKN-H
469
12. WALL MOUNTED TYPEPACKAGED AIR-CONDITIONER
Split system, Air to airheat pump type
Refrigerant R22 use modelsFDKN208HEN-S1
258HEN-S1
Alternative refrigerant R407C use modelsFDKNP208HEN-S
258HEN-S308HEN-S308HES-S
( )
FDKN-H
470
FDKN-H
CONTENTS
12.1 GENERAL INFORMATION ........................................................................ 471
12.1.1 Specific features ................................................................................. 471
12.1.2 How to read the model name ............................................................. 471
12.2 SELECTION DATA..................................................................................... 472
12.2.1 Specifications ...................................................................................... 472
12.2.2 Range of usage & limitations ............................................................. 478
12.2.3 Exterior dimensions............................................................................ 479
12.2.4 Exterior appearance............................................................................ 485
12.2.5 Piping system...................................................................................... 486
12.2.6 Selection chart .................................................................................... 488
12.2.7 Noise level ........................................................................................... 490
12.3 ELECTRICAL DATA .................................................................................. 491
12.3.1 Electrical wiring .................................................................................. 491
12.4 OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER ............. 497
12.5 APPLICATION DATA ................................................................................. 497
12.5.1 Installation of indoor unit ................................................................... 498
12.5.2 Installation of outdoor unit................................................................. 501
12.6 MAINTENANCE DATA............................................................................... 501
471
FDKN-H
FDKN : Wall mounted type unit with
wireless remote controller.
FDC : Outdoor unit
Applicable power source ... See the specifications
Heat pump type
Series No
Product capacity
P : R407C model
: R22 model
Model name
Example: FDKN P 25 8 H EN - S
12.1 GENERAL INFORMATION12.1.1 Specific features(1) Less refrigerant charge amount due to use of double phase refrigerant flow system. The total refrigerant charge amount has been
reduced by more than 50%.
(2) The indoor outdoor interconnection signal wiring has been done away with. The microcomputer chip is installed in the indoor unit.
There is no need for the unit to communicate between the outdoor and indoor units so the unit is more resistant to electromagnetic
noise thus the incidence of microcomputer malfunction has been reduced. The compressor in the outdoor unit has its own self
protection function, that reacts according to abnormal high pressure and excessive high temperature.
(3) There are only five power line between the outdoor and indoor unit. As no signal wire is used there is no need to separate the power
line from the signal line. One cab tyre cable with 6 wires encased in one sheath is enough for conducting the wiring work between
the outdoor unit and the indoor unit. This contributes to simpler wiring work in the field.
(4) All air supply ports have auto swing louvers. The indoor fan motor has two speeds of high and low.
(5) All models have service valves protruding from the outdoor unit for faster flare connection work in the field.
(6) Aero trap louver
(a) Pleasantness will be enhanced with the employment of aero trap louver. It has an excellent wind orientation and a homogeneous
air conditioning feeling is ensured at every corner in a room with the auto swing blasting which can be adjusted the maximum
70° downward.
(b)Louver angle can be adjusted to 4 fixed positions with the remote control. It can be adjusted at any optional angle during the
manual operation. Sidewise blast is adjustable by 40° in each direction.
(7) Low noise
(a) Specially developed silent fan is employed. A very gentle operation sound is assured because the noise like wind slashing sound
are suppressed effectively.
(8) Thin and compact design
(a) The unit measures 17.9 cm (208 type) or 19.6 cm (258, 308 type) in thickness and its size is so compact as a room air condi
tioner. Body of the unit is dinished in the ivory white color and a pleasant and simple design produces a very pleasant harmony
for the interior design.
12.1.2 How to read the model name
472
FDKN-H
ItemModel
FDKN208H FDC208HEN3ANominal cooling capacity(1) W 4850
Nominal heating capacity(1) W 5400
Power source 1 Phase, 220/240V, 50Hz
Cooling input kW 1.76/1.85
Running current (Cooling) A 8.2/8.0
Power factor (Cooling) % 98/96
Heating input kW 1.72/1.82
Running current (Heating) A 8.0/7.8
Power factor (Heating) % 98/97
Inrush current (L.R.A) A 44
Noise level(4) dB(A) Hi: 45 Lo: 38 52
Exterior dimensionsmm 275 × 790 × 179 690 × 880 × 290
Height × Width × Depth
Net weight kg 10 49
Refrigerant equipment– RM5523GNE4 × 1
Compressor type & Q’ty
Motor kW – 1.7
Starting method – Line starting
Heat exchanger Louver fins & inner grooved tubing Slitted fins & bare tubing
Refrigerant control Capillary tube
Refrigerant R22
Quantity kg Holding charged 0.98 [Pre-charged up to the piping length of 5m]
Refrigerant oil r – 0.7 (BARREL FREEZE 32SAM)
Defrost control MC controlled de-icer
High pressure control High pressure switch
Air handling equipment
Fan type & Q’tyTangential fan × 1 Propeller fan × 1
Motor W 26 × 1 55 × 1
Starting method Line starting Line starting
Air flow (Standard) CMM Hi:16 Lo:10 56
Fresh air intake Unavailable –
Air filter, Q’ty Long life filter ×2(washable) –
Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor)
Electric heater W – 20 (Crank case heater)
Operation control
Operation switch Wireless remote control switch – (Indoor unit side)
Room temperature control Thermostat by electronics –
Safety equipment Internal thermostat for fan motor. Internal thermostat for fan motor.
Frost protection thermostat. Abnormal discharge temperature protection
Installation data mmLiquid line: φ6.35 (1/4″) Gas line: φ15.88 (5/8″)
Refrigerant piping size (in)
Connecting method Flare piping
Drain hose (Connectable with VP16) –
Insulation for piping Necessary (both Liquid & Gas lines)
Accessories Mounting kit. Wireless remote controller. Drain hose
Optional parts –
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. JIS B8616 “UNITARY AIR-CONDITIONERS”
(3) The operation data indicate when the air-conditioner is operated at 220/240V 50Hz.
(4) Indicates the value at mild mode.
Notes (1) The data are measured at the following conditions.
Item Indoor air temperature Outdoor air temperatureStandards
Operation DB WB DB WB
Cooling 27˚C 19˚C 35˚C 24˚C
Heating 20˚C – 7˚C 6˚CISO-T1, JIS B8616
Op
erat
ion
dat
a(3)
FDKN208HEN-S1
(1) Refrigent R22 use modelsModel FDKN208HEN-S1
12.2 SELECTION DATA12.2.1 Specifications
473
FDKN-H
ItemModel
FDKN258H FDC258HEN3ANominal cooling capacity(1) W 5700
Nominal heating capacity(1) W 6100
Power source 1 Phase, 220/240V, 50Hz
Cooling input kW 2.03/2.14
Running current (Cooling) A 9.3/9.3
Power factor (Cooling) % 99/96
Heating input kW 1.93/2.08
Running current (Heating) A 9.0/9.1
Power factor (Heating) % 97/95
Inrush current (L.R.A) A 51
Noise level(4) dB(A) Hi: 45 Lo: 38 52
Exterior dimensionsmm 298 × 940 × 196 845 × 880 × 340
Height × Width × Depth
Net weight kg 11 55
Refrigerant equipment– RM5526GNE4 × 1
Compressor type & Q’ty
Motor kW – 1.9
Starting method – Line starting
Heat exchanger Louver fins & inner grooved tubing Slitted fins & bare tubing
Refrigerant control Capillary tube
Refrigerant R22
Quantity kg Holding charged 1.1 [Pre-charged up to the piping length of 5m]
Refrigerant oil r – 0.7 (BARREL FREEZE 32SAM)
Defrost control MC controlled de-icer
High pressure control High pressure switch
Air handling equipment
Fan type & Q’tyTangential fan × 1 Propeller fan × 1
Motor W 40 × 1 55 × 1
Starting method Line starting Line starting
Air flow (Standard) CMM Hi:17 Lo:10 56
Fresh air intake Unavailable –
Air filter, Q’ty Long life filter ×2(washable) –
Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor)
Electric heater W – 20 (Crank case heater)
Operation control
Operation switch Wireless remote control switch – (Indoor unit side)
Room temperature control Thermostat by electronics –
Safety equipment Internal thermostat for fan motor. Internal thermostat for fan motor.
Frost protection thermostat. Abnormal discharge temperature protection
Installation data mmLiquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)
Refrigerant piping size (in)
Connecting method Flare piping
Drain hose (Connectable with VP16) –
Insulation for piping Necessary (both Liquid & Gas lines)
Accessories Mounting kit. Wireless remote controller. Drain hose
Optional parts –
Model FDKN258HEN-S1
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. JIS B8616 “UNITARY AIR-CONDITIONERS”
(3) The operation data indicate when the air-conditioner is operated at 220/240V 50Hz.
(4) Indicates the value at mild mode.
Notes (1) The data are measured at the following conditions.
Item Indoor air temperature Outdoor air temperatureStandards
Operation DB WB DB WB
Cooling 27˚C 19˚C 35˚C 24˚C
Heating 20˚C – 7˚C 6˚CISO-T1, JIS B8616
Op
erat
ion
dat
a(3)
FDKN258HEN-S1
474
FDKN-H
ItemModel
FDKN208H FDCP208HEN3ANominal cooling capacity(1) W 4850
Nominal heating capacity(1) W 5400
Power source 1 Phase, 220/240V, 50Hz
Cooling input kW 2.07/2.14
Running current (Cooling) A 9.5/9.6
Power factor (Cooling) % 99/93
Heating input kW 1.97/2.11
Running current (Heating) A 9.3/9.5
Power factor (Heating) % 96/93
Inrush current (L.R.A) A 44
Noise level(4) dB(A) Hi: 45 Lo: 38 52
Exterior dimensionsmm 275 × 790 × 179 690 × 880 × 290
Height × Width × Depth
Net weight kg 10 49
Refrigerant equipment– RM5523HNE5 × 1
Compressor type & Q’ty
Motor kW – 1.7
Starting method – Line starting
Heat exchanger Louver fins & inner grooved tubing Slitted fins & bare tubing
Refrigerant control Capillary tube
Refrigerant R407C
Quantity kg Holding charged 0.98 [Pre-charged up to the piping length of 5m]
Refrigerant oil r – 0.7 (MA32)
Defrost control IC controlled de-icer
High pressure control High pressure switch
Air handling equipment
Fan type & Q’tyTangential fan × 1 Propeller fan × 1
Motor W 26 × 1 55 × 1
Starting method Line starting Line starting
Air flow (Standard) CMM Hi:16 Lo:10 56
Fresh air intake Unavailable –
Air filter, Q’ty Long life filter ×2(washable) –
Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor)
Electric heater W – 20 (Crank case heater)
Operation control
Operation switch Wireless remote control switch – (Indoor unit side)
Room temperature control Thermostat by electronics –
Safety equipment Internal thermostat for fan motor.
Frost protection thermostat.
Installation data mmLiquid line: φ6.35 (1/4″) Gas line: φ15.88 (5/8″)
Refrigerant piping size (in)
Connecting method Flare piping
Drain hose (Connectable with VP16) –
Insulation for piping Necessary (both Liquid & Gas lines)
Accessories Mounting kit. Wireless remote controller. Drain hose
Optional parts –
Model FDKNP208HEN-S
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. JIS B8616 “UNITARY AIR-CONDITIONERS”
(3) The operation data indicate when the air-conditioner is operated at 220/240V 50Hz.
(4) Indicates the value at mild mode.
Notes (1) The data are measured at the following conditions.
Item Indoor air temperature Outdoor air temperatureStandards
Operation DB WB DB WB
Cooling 27˚C 19˚C 35˚C 24˚C
Heating 20˚C – 7˚C 6˚CISO-T1, JIS B8616
Op
erat
ion
dat
a(3)
FDKNP208HEN-S
(2) Alternative refrigerant R407C use models
Internal thermostat for fan motor.Thermostat for discharge temperature.
High pressure swich for protection
475
FDKN-H
ItemModel
FDKN258H FDCP258HEN3ANominal cooling capacity(1) W 5700
Nominal heating capacity(1) W 6100
Power source 1 Phase, 220/240V, 50Hz
Cooling input kW 2.34/2.54
Running current (Cooling) A 11.3/12.5
Power factor (Cooling) % 94/85
Heating input kW 2.08/2.33
Running current (Heating) A 10.4/11.9
Power factor (Heating) % 91/82
Inrush current (L.R.A) A 51
Noise level(4) dB(A) Hi: 45 Lo: 38 52
Exterior dimensionsmm 298 × 940 × 196 845 × 880 × 340
Height × Width × Depth
Net weight kg 11 55
Refrigerant equipment– RM5526HNE5 × 1
Compressor type & Q’ty
Motor kW – 1.9
Starting method – Line starting
Heat exchanger Louver fins & inner grooved tubing Slitted fins & bare tubing
Refrigerant control Capillary tube
Refrigerant R407C
Quantity kg Holding charged 1.1 [Pre-charged up to the piping length of 5m]
Refrigerant oil r – 0.7 (MA32)
Defrost control IC controlled de-icer
High pressure control High pressure switch
Air handling equipment
Fan type & Q’tyTangential fan × 1 Propeller fan × 1
Motor W 40 × 1 55 × 1
Starting method Line starting Line starting
Air flow (Standard) CMM Hi:17 Lo:10 56
Fresh air intake Unavailable –
Air filter, Q’ty Long life filter ×2(washable) –
Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor)
Electric heater W – 20 (Crank case heater)
Operation control
Operation switch Wireless remote control switch – (Indoor unit side)
Room temperature control Thermostat by electronics –
Safety equipment Internal thermostat for fan motor.
Frost protection thermostat.
Installation data mmLiquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)
Refrigerant piping size (in)
Connecting method Flare piping
Drain hose (Connectable with VP16) –
Insulation for piping Necessary (both Liquid & Gas lines)
Accessories Mounting kit. Wireless remote controller. Drain hose
Optional parts –
Model FDKNP258HEN-S
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. JIS B8616 “UNITARY AIR-CONDITIONERS”
(3) The operation data indicate when the air-conditioner is operated at 220/240V 50Hz.
(4) Indicates the value at mild mode.
Notes (1) The data are measured at the following conditions.
Item Indoor air temperature Outdoor air temperatureStandards
Operation DB WB DB WB
Cooling 27˚C 19˚C 35˚C 24˚C
Heating 20˚C 12˚C 7˚C 6˚CISO-T1, JIS B8616
Op
erat
ion
dat
a(3)
FDKNP258HEN-S
Internal thermostat for fan motor.Thermostat for discharge temperature.
High pressure swich for protection
476
FDKN-H
ItemModel
FDKN308H FDCP308HEN3Nominal cooling capacity(1) W 7100
Nominal heating capacity(1) W 8000
Power source 1 Phase, 220/240V, 50Hz
Cooling input kW 3.18/3.33
Running current (Cooling) A 14.8/15.2
Power factor (Cooling) % 98/91
Heating input kW 2.93/3.07
Running current (Heating) A 13.8/14.2
Power factor (Heating) % 97/90
Inrush current (L.R.A) A 95
Noise level(4) dB(A) Hi 46 Lo:40 52
Exterior dimensionsmm 298 × 1155 × 196 845 × 880 × 340
Height × Width × Depth
Net weight kg 13.5 76
Refrigerant equipment– GT-A5534HN41 × 1
Compressor type & Q’ty
Motor kW – 2.5
Starting method – Line starting
Heat exchanger Louver fins & inner grooved tubing Slitted fins & bare tubing
Refrigerant control Capillary tube
Refrigerant R407C
Quantity kg Holding charged 1.75 [Pre-charged up to the piping length of 5m]
Refrigerant oil r – 1.45 (MA32)
Defrost control IC controlled de-icer
High pressure control High pressure switch
Air handling equipment
Fan type & Q’tyTangential fan × 1 Propeller fan × 1
Motor W 40 × 1 55 × 1
Starting method Line starting Line starting
Air flow (Standard) CMM Hi:21 Lo:15 58
Fresh air intake Unavailable –
Air filter, Q’ty Long life filter ×3(washable) –
Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor)
Electric heater W – 33 (Crank case heater)
Operation control
Operation switch Wireless remote control switch – (Indoor unit side)
Room temperature control Thermostat by electronics –
Safety equipment Internal thermostat for fan motor.
Frost protection thermostat.
Installation data mmLiquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)
Refrigerant piping size (in)
Connecting method Flare piping
Drain hose (Connectable with VP16) –
Insulation for piping Necessary (both Liquid & Gas lines)
Accessories Mounting kit. Wireless remote controller. Drain hose
Optional parts –
Model FDKNP308HEN-SO
per
atio
n d
ata(3
)
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. JIS B8616 “UNITARY AIR-CONDITIONERS”
(3) The operation data indicate when the air-conditioner is operated at 220/240V 50Hz.
(4) Indicates the value at mild mode.
Notes (1) The data are measured at the following conditions.
Item Indoor air temperature Outdoor air temperatureStandards
Operation DB WB DB WB
Cooling 27˚C 19˚C 35˚C 24˚C
Heating 20˚C – 7˚C 6˚CISO-T1, JIS B8616
FDKNP308HEN-S
Internal thermostat for fan motor.Thermostat for discharge temperature.
High pressure swich for protection
477
FDKN-H
ItemModel
FDKN308H FDCP308HES3Nominal cooling capacity(1) W 7100
Nominal heating capacity(1) W 8000
Power source 3 Phase, 380/415V, 50Hz
Cooling input kW 3.10/3.25
Running current (Cooling) A 5.4/5.7
Power factor (Cooling) % 87/79
Heating input kW 2.95/3.09
Running current (Heating) A 5.4/5.7
Power factor (Heating) % 82/75
Inrush current (L.R.A) A 45
Noise level(4) dB(A) Hi 46 Lo:40 52
Exterior dimensionsmm 298 × 1155 × 196 845 × 880 × 340
Height × Width × Depth
Net weight kg 13.5 76
Refrigerant equipment– GT-A5534HS41 × 1
Compressor type & Q’ty
Motor kW – 2.5
Starting method – Line starting
Heat exchanger Louver fins & inner grooved tubing Slitted fins & bare tubing
Refrigerant control Capillary tube
Refrigerant R407C
Quantity kg Holding charged 1.75 [Pre-charged up to the piping length of 5m]
Refrigerant oil r – 1.45 (MA32)
Defrost control IC controlled de-icer
High pressure control High pressure switch
Air handling equipment
Fan type & Q’tyTangential fan × 1 Propeller fan × 1
Motor W 40 × 1 55 × 1
Starting method Line starting Line starting
Air flow (Standard) CMM Hi:21 Lo:15 58
Fresh air intake Unavailable –
Air filter, Q’ty Long life filter ×3(washable) –
Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor)
Electric heater W – 33 (Crank case heater)
Operation control
Operation switch Wireless remote control switch – (Indoor unit side)
Room temperature control Thermostat by electronics –
Safety equipment Internal thermostat for fan motor.
Frost protection thermostat.
Installation data mmLiquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)
Refrigerant piping size (in)
Connecting method Flare piping
Drain hose (Connectable with VP16) –
Insulation for piping Necessary (both Liquid & Gas lines)
Accessories Mounting kit. Wireless remote controller. Drain hose
Optional parts –
Model FDKNP308HES-SO
per
atio
n d
ata(3
)
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. JIS B8616 “UNITARY AIR-CONDITIONERS”
(3) The operation data indicate when the air-conditioner is operated at 380/415V 50Hz.
(4) Indicates the value at mild mode.
Notes (1) The data are measured at the following conditions.
Item Indoor air temperature Outdoor air temperatureStandards
Operation DB WB DB WB
Cooling 27˚C 19˚C 35˚C 24˚C
Heating 20˚C – 7˚C 6˚CISO-T1, JIS B8616
FDKNP308HES-S
Internal thermostat for fan motor.Thermostat for discharge temperature.
High pressure swich for protection
478
FDKN-H
Item
ModelsFDKN (P) 208, 258 type FDKNP308 type
Indoor return air temperature(Upper, lower limits)
Refer to the selection chart
Outdoor air temperature(Upper, lower limits)
Refrigerant line (one way) length Max. 30 m Max. 50 m
Vertical height difference between Max. 20 m (Outdoor unit is higher) Max. 30 m (Outdoor unit is higher)outdoor unit and indoor unit Max. 15 m (Outdoor unit is lower) Max. 15 m (Outdoor unit is lower)
Power source voltage Rating ± 10%
Voltage at starting Min. 85% of rating
Frequency of ON-OFF cycle Max. 10 times/h
ON and OFF interval Min. 3 minutes
12.2.2 Renge of usage & limitations
479
FDKN-H
12.2.3 Exterior dimensions(1) Indoor unit
Model FDKN208H
Space for installation and service
120 or
more
65 o
r
mor
e
120 or
more
VIEW A (Rear side)
600
Hole on wall forrear connection(φ65)
Indoor unit Mounting plate
15 760 15
170 450 170
50 50 50 50
46
9
6118
7.5
261.
5
36
Hole on wall forrear connection(φ65)
67
Drain hose (VP16)
Gas piping
φ15.88(5/8˝)
Liquid piping
82
4.5
390
440
φ6.35(1/4˝)
784
68 26
40
790
275
Remote controllersignal receives
179 3
56
Outlet for piping
(On both side)
49Lower piping outlet(Refer to the top view.)
9
Outer for electricwiring
A
Unit : mm
Mounting plate
480
FDKN-H
Model FDKN258HUnit: mm
930
75 45
51
940
298
Remote controllersignal receives
196 3
Mounting plate
A
55 Outer forelectric wiring
51
9
Outlet for piping
(On both side)
Lower piping outlet
(Refer to the top view.)
Space for installation and service
120 ormore
90 o
rm
ore
120 ormore
VIEW A (Rear side)
Indoor unit
Mounting plate55 832 53
245 450 245
50 50 50 50
60
55 9
209 28
3
37
Hole on wall forrear connecting(φ65)
72
Drain hose(VP16)
Liquid pipingφ9.52(3/8˝)
Gas pipingφ15.88(5/8˝)
463
518
600
65
Hole on wall forrear connection(φ65)
7
481
FDKN-H
Model FDKN308H
Unit : mm
35 75
51
450
690
4575
51
104754
515
600
37
6020
9
245
50
Lower piping outlet
Indoor unit
Gas piping
Hole on wall forrear connecting(ø65)
ø15.88 (5/8'')
Mounting plate
Remote controllersignal receives
Outlet for piping(On both side)
Outlet for electric wiring
Mounting plate
(Refer to the top view)
50
220
54
1155
298
1145
196
955
3
51
120 or more
120 or more
90 o
r m
ore
Space for installation and service
45
450
245 465
6572
928
2.5
6.5
4 - 5.5 ✕ 15(Long hole)
Drain hose(VP16)Liquid piping
ø9.52 (3/8'')
8 - 12 ✕ 18(Long hole)
5050
Hole on wall forrear connecting(ø65)
A
VIEW A (Rear side)
482
FDKN-H
MODE TEMP ON/OFF
AUTO COOL DRY FAN HEAT FILTER
°CAMPMON AM
PMOFF
FAN HI LO
(2) Wireless remote controller
60 20.5
161.
5
(3) Indication board of indoor unit
Unit: mm
483
FDKN-H
Minimum allowable space to the obstacles
Unit: mm
Installation type1 2 3
Mark
L1 Open Open 500
L2 300 5 Open
L3 100 150 100
L4 5 5 5
Liquid piping φ6.35 (1/4˝)
(Flare connecting)
Gas piping: φ15.88 (5/8˝)
(Flare connecting)
40
40
95
53
Terminal block
Liquid piping: φ6.35 (1/4˝)
(Flare connecting)
Gas piping: φ15.88 (5/8˝)
(Flare connecting)
Opening for electric wiring
690
10 110 19
5 331
351
Opening for pipingand electric wiring 40
50
50
15
880
110
195
5027
50
50
Opening for piping andelectric wiring
Holes for anchor bolt
(M10 × 4 pcs. )
Electric wiring
(4) Outdoor unitModels FDC208HEN3A
FDCP208HEN3A
Notes(1) Avoid the location where four sides are entirely
surrounded by walls.(2) Fix the unit by anchor bolts without fail. Restrict
the protrusion length of anchor bolt to 15 mm andunder.
(3) When strong wind blows against the unit, directthe discharge port at a right angle to the winddirection.
(4) Secure the space of 1 m and over at the top ofunit.
(5) Make the height of obstruction wall in front of dis-charge port lower than the height of unit.
( )Maintenancespace
VIEW A
A
Unit : mm
Required space for maintenance and air flow
55
1533
0
290 55
15
3535
260 335 Holes for drain
(φ20 × 3 pcs. )
50 15
150 580 150
1510
3
40
Opening forelectric wiring
Opening for piping andelectric wiring
150
7050
5015
40
L1
Air outlet
L3
L2
L4
Airinlet
Air inlet
484
FDKN-H
Liquid piping: ø9.52 (3/8")
(Flare connecting)
Gas piping: ø15.88 (5/8")
Terminal block
Opening forelectric wiring Opening for
electric wiring
Holes for anchor bolt(M10 × 4 pcs.)
Holes for drain(ø9.52 × 3pcs.)
Electric wiring Opening for pipingand electric wiring
Opening for pipingand electric wiringOpening for piping
and electric wiring
(Flare connecting)
845
10
50
380
1515
340
55
1510
3
150
7050
47
3535
110
460 11
0
195
50
195
40
880
310222
40
L2
L3
L4
L1
Airinlet
Air inlet
Air outletMaintenancespace
150 580 150
50 15 15 50
50
50
502750 15
Models FDC258HEN3A FDCP258HEN3A, 308HEN3, 308HES3
Required space for maintenance and air flow Minimum allowable space to the obstacles
Unit:mm
Mark1 2 3
L1 Open Open 500
L2 300 5 Open
L3 100 150 100
L4 5 5 5
Installationtype
Notes(1) Avoid the location where four sides are entirely
surrounded by walls.(2) Fix the unit by anchor bolts without fail. Restrict
the protrusion length of anchor bolt to 15 mmand under.
(3) When strong wind blows against the unit, di-rect the discharge port at a right angle to thewind direction.
(4) Secure the space of 1 m and over at the top ofunit.
(5) Make the height of obstruction wall in front ofdischarge port lower than the height of unit.
Unit: mm
VIEW A
Liquid piping: ø9.52 (3/8")
(Flare connecting)
Gas piping: ø15.88 (5/8")
(Flare connecting)
40 53
95
40
485
FDKN-H
12.2.4 Exterior appearance(1) Indoor unit
Models All models
Ivory white(Air inlet grill)
Ivory white(Front panel)
Ivory white(Louver)
Ivory white(Base)
(2) Outdoor unitModels FDC208HEN3A FDCP208HEN3A
Polar white
Polar white
Models FDC258HEN3A FDCP258HEN3A, 308HEN3, 308HES3
486
FDKN-H
Service valve
(Flare connecting)
Service valve(Flare connecting)
Gas line(308:ø15.88)
Strainer
Thermistor
(ThO-D) Strainer
Capillarytube
Check valve Solenoid valve (SV2)
Capillary tube
Strainer
Strainer
Thermistor
(ThO-R)
Thermistor
(ThO-A)
Thermistor
(ThI-A)
Thermistor
(ThI-R)
Heat exchanger
Heat exchanger
Sub-coolingcoil
Flareconnecting
Liquid line(ø9.52)
Capillarytube
Checkjoint
Check joint
4way valve
Cooling cycle
Outdoor unitHeating cycle
High pressure switch (63H2)
(For fan motor control)
Check joint
MufflerSolenoidvalve
(SV1)Accumulator
Compressor
Indoor unit
High pressureswitch (63H1)
Models FDKNP308HEN-S, 308HES-S
Service valve
(Flare connecting)
Service valve(Flare connecting)
Gas line(ø15.88)
Strainer
Thermistor
(ThO-D) Strainer
Capillarytube
Check valve
Capillary tube
Strainer
Strainer
Thermistor
(ThO-R)
Thermistor
(ThO-A)
Thermistor
(ThI-A)
Thermistor
(ThI-R)
Heat exchanger
Heat exchanger
Sub-coolingcoil
Flareconnecting
Liquid line
(208:ø6.35)258:ø9.52
Capillarytube
Checkjoint
Check joint
High pressureswitch (63H1)Only case of FDKNP model
4way valve
Cooling cycle
Outdoor unitHeating cycle
High pressure switch (63H2)
(For fan motor control)
Check joint
MufflerSolenoidvalve
(SV1)Accumulators
Compressor
Indoor unit
( )
12.2.5 Piping systemModels FDKN208HEN-S1, 258HEN-S1, FDKNP208HEN-S, 258HEN-S
487
FDKN-H
Preset point of the protective devicesParts name Mark Equipped unit FDKN208, 258 type FDKNP208~308 type
Thermistor(for protection over loading in heating)
Thermistor(for detecting discharge pipe temp.)
Thermistor(for detecting heat exchanger temp.)
Thermistor(for frost prevention)
High pressure switch(for controlling FMo)
ThI-R
ThO-D
ThO-R
Indoor unit
Outdoor unit
Outdoor unit
Outdoor unit
63H2
OFF 68 °CON 61 °C
OFF 2.5 °CON 10 °C
OFF 135 °CON 90 °C
OFF 70 °CON 60 °C
OFF 2.5MPa (25.5kgf/cm2)ON 2.06MPa (21kgf/cm2)
High pressure switch(for protection) Outdoor unit63H1
OFF 3.24MPa (33kgf/cm2)ON 2.65MPa (27kgf/cm2)
488
FDKN-H
12.2.6 Selection chartCorrect the cooling and heating capacity in accordance with the conditions as follows. The net cooling and heating capacity can be
obtained in the following way.
Net capacity = Capacity shown on specification × Correction factors as follows.
(1) Coefficient of cooling and heating capacity in relation to temperaturesModels FDKN208HEN-S1, 258HENS-1, FDKNP208HEN-S, 258HEN-S
Indoor air W.B. temperature (˚CW.B.) ISO-T1 Standard condition
Ou
tdo
or
air
D.B
.te
mp
erat
ure
(˚C
D.B
.)
Co
olin
g o
per
atio
n
Ind
oo
r ai
r D
.B.
tem
per
atu
re (
˚CD
.B.)
Hea
tin
g o
per
atio
n
ISO-T1 Standard condition
Outdoor air W.B. temperature (˚CW.B.)
Models FDKN308HEN-S, 308HES-S
Outdoor air W.B. temperature (˚CW.B.)
Indoor air W.B. temperature (˚CW.B.) ISO-T1 Standard condition
Ou
tdo
or
air
D.B
.te
mp
erat
ure
(˚C
D.B
.)
Co
olin
g o
per
atio
n
Ind
oo
r ai
r D
.B.
tem
per
atu
re (
˚CD
.B.)
Hea
tin
g o
per
atio
n
Co
effi
cien
t o
f co
olin
g a
nd
hea
tin
g c
apac
ity
in r
elat
ion
to
tem
per
atu
res
489
FDKN-H
(3) Correction of cooling and heating capacity in relation to one way length of refrigerant piping
It is necessary to correct the cooling and heating capacity in relation to the one way equivalent piping length between the indoor
and outdoor units.
Note (1) Equivalent piping length can be obtained by calculating as follows.
208, 258, 308 series [φ15.88(5/8″)]: Equivalent piping length = Real piping length + (0.10 × Number or bends in piping)
[Equivalent piping length < Limitation length of piping + 5m]
(4) When the outdoor unit is located at a lower height than the indoor unit in cooling operation and when the
outdoor unit is located at a higher height than the indoor unit in heating operation, the following values should be
subtracted from the values in the above table.
Equivalent piping length(1) m 5 10 15 20 25 30 35 40 45 50 55
Heating 1.0 1.0 1.0 1.0 1.0 0.995 0.995 0.99 0.99 0.985 0.985
FDKN (P) 208 type 1.0 0.995 0.995 0.99 0.985 0.985 0.98
FDKN (P) 258 type 1.0 0.995 0.99 0.985 0.98 0.975 0.97
FDKNP 308 type 1.0 0.99 0.98 0.97 0.96 0.95 0.94 0.93 0.92 0.91 0.9
Co
olin
g
Item
Air flow Hi 0.03 0.03 0.04
FDKN (P) 208 type FDKN (P) 258 type FDKNP308 type
(2) Correction of cooling and heating capacity in relation to air flow rate control (fan speed)
Coefficient: 1.00 at High, 0.95 at Low
Table of bypass factor
Model
Height difference between the indoor unit andoutdoor unit in the vertical height difference 5m 10m 15m 20m 25m 30m
Adjustment coefficient 0.01 0.02 0.03 0.04 0.05 0.06
Piping length limitations
ItemModel FDKN(P) 208, 258 type FDKNP308 type
Max. one way piping length 30m 50m
20m (Outdoor unit is higher) 30m (Outdoor unit is higher)Max. vertical height difference
15m (Outdoor unit is lower) 15m (Outdoor unit is lower)
Note(1) Values in the table indicate the one way piping length between the indoor and outdoor units.
How to obtain the cooling capacity
Example: The net cooling capacity of the model FDKNP308HEN-S with the air flow “High”, the piping length of 15m, the outdoor
unit located 5m lower than the indoor unit, indoor wet-bulb temperature at 19.0 ˚C and outdoor dry-bulb temperature 35 ˚C
isNet cooling capacity = 7100 × 1.00 × (0.98 - 0.01) × 1.0 = 6887 w
Factor by airtemperatures
FDKNP308HEN-S Air flow“High”
Length 15m.Height difference 5 m
490
FDKN-H
Mid octave band frequency (Hz)
N30N20
N50
N60
N70
63 125 250 500 1000 2000 4000 800020
30
40
50
60
70
20
30
40
50
60
70
N40
Soun
d pr
essu
re le
vel
(Sta
ndar
d 0.
0002
µ ba
r) d
B
12.2.7 Noise levelNotes (1) The data are based on the following conditions.
Ambient air temperature:Indoor unit 27°C DB, 19°C WBOutdoor unit 35°C DB,
(2) The data in the chart are measured in an unechonic room.(3) The noise levels measured in the field are usually higher than the data because of reflection.
(1) Indoor unit
Unit
1 m1 m
Mike(Center & Low points)
Souu
d p
ress
ure
leve
l (
stan
dard
0.0
002µ
bar)
Mid octave band frequency (Hz)
N30N20
N50
N60
N70
63 125 250 500 1000 2000 4000 800020
30
40
50
60
70
20
30
40
50
60
70
N40
Mid octave band frequency (Hz)
N30N20
N50
N60
N70
63 125 250 500 1000 2000 4000 800020
30
40
50
60
70
20
30
40
50
60
70
N40
Soun
d pr
essu
re le
vel
(Sta
ndar
d 0.
0002
µ ba
r) d
B
Mid octave band frequency (Hz)
N30N20
N50
N60
N70
63 125 250 500 1000 2000 4000 800020
30
40
50
60
70
20
30
40
50
60
70
N40
Soun
d pr
essu
re le
vel
(Sta
ndar
d 0.
0002
µ ba
r) d
B
Indoor unitMeasured based on JIS B 8616Mike position as below
Model FDKN208HNoise level 45dB (A) at HIGH
38dB (A) at LOW
Outdoor unitMeasured based on JIS B 8616Mike position: at highest noise level
in position as belowDistance from front side 1 mHeight 1 m
Model FDKN258HNoise level 45dB (A) at HIGH
38dB (A) at LOW
Model FDKN308HNoise level 46dB (A) at HIGH
40dB (A) at LOW
(2) Outdoor unit
Model FDC208HEN3ANoise level 52dB (A)
Model FDC258HEN3ANoise level 52dB (A)
Mid octave band frequency (Hz)
N30N20
N50
N60
N70
63 125 250 500 1000 2000 4000 800020
30
40
50
60
70
20
30
40
50
60
70
N40
Soun
d pr
essu
re le
vel
(Sta
ndar
d 0.
0002
µ ba
r) d
B
Model FDCP208HEN3ANoise level 52dB (A)
Model FDCP258HEN3ANoise level 52dB (A)
Mid octave band frequency (Hz)
N30N20
N50
N60
N70
63 125 250 500 1000 2000 4000 800020
30
40
50
60
70
20
30
40
50
60
70
N40
Soun
d pr
essu
re le
vel
(Sta
ndar
d 0.
0002
µ ba
r) d
B
Souu
d p
ress
ure
leve
l (
stan
dard
0.0
002µ
bar)
Mid octave band frequency (Hz)
N30N20
N50
N60
N70
63 125 250 500 1000 2000 4000 800020
30
40
50
60
70
20
30
40
50
60
70
N40
Models FDCP308HEN3, 308HES3Noise level 52dB (A)
Mid octave band frequency (Hz)
N30N20
N50
N60
N70
63 125 250 500 1000 2000 4000 800020
30
40
50
60
70
20
30
40
50
60
70
N40
Soun
d pr
essu
re le
vel
(Sta
ndar
d 0.
0002
µ ba
r) d
B
491
FDKN-H
Model FDKN208HEN-S1
Co
lor
mar
k
Mar
kC
olo
rB
KB
lack
BL
Blu
eB
RB
row
nG
RG
ray
OR
Ora
nge
PK
Pink
RD
Red
WH
Whi
teY
Yel
low
Mar
kC
olo
rB
K/R
DB
lack
/Red
BK
/WH
Bla
ck/W
hite
BL
/WH
Blu
e/W
hite
BR
/WH
Bro
wn/
Whi
teO
R/W
HO
rang
e/W
hite
RD
/WH
Red
/Whi
teY
/GN
Yel
low
/Gre
en
Po
wer
so
urc
e1
Ph
ase
220/
240V
50H
z
XR
3
XR
5
BK
BK
XR
1
Op
tio
n
Th
l-A
XR
2
XR
4
BK
BK
Th
l-R
BK
BK
BK
BK
BK
BK
Rec
eive
ram
p.
Wir
eles
sre
mo
teco
ntr
olle
r
LED
1
LED
2
TB
TB
52X5
FMI
(49F
I)
LM
SW
SW
3
CnCCnNCnH CnACnT
52X6
52X
552
X6
PC
Cn
FC
nJ
Cn
QT
est
RD
RD/W
H
BK/
WH
BK/
RD
BL/
WH
BR/
WH
Y/GN
WH
BK
BL
21 9 10 14
RD
21
4O
NO
FF
Pri
nte
d c
ircu
it b
oar
d3
BLPK
ORBR
RD
WHBLY
3
BR
Y/G
N
BK
DR
DR
Tho-
R
63H
2
Cn
L
LED
-R
LED
-G
(Ch
eck)
(Ru
n)
Cn
E
Vao(C
hec
ker) Cn
A1 T
roCn
A2
BK
Tho-
D
BK
Tho-
A
6
14V
27
BL/WH
BK/RD
BR/WH
BL
BL
P
P
BR
BR
BK
BK
BK
BK
2625
2120
1918
1716
1312
2
31
42
Pri
nte
d c
ircu
it b
oar
d
3
HL
UH
A1CF
01A2
28
X05
X02
X01
X03
X04
X06
X07
X01
220/240V
7
PC
PC
CnR
CnM1
CH
X04
X07
X02
X05
X03
X06
1 22/
N
33
44
55
F(3.15A)
OR/WH
OR/WH
ORORWHBRBLBK
WHWH
RDBL
Y/GN
WHRD
RD
BK
/WH
WH
CT
1
R
S
C
52C
Cc
RD/WH
RD
BK/WH
NTB
SV
152
C20
S
NR
FMO1
(49F
O1)
CM
Val
BKRD
BKBR
CnW1
CnW2
TrI
220/240V
14V
16V
Ou
tdo
or
Un
itIn
do
or
Un
it
1L
12.3 ELECTRICAL DATA12.3.1 Electrical wiring
Mea
nin
g o
f m
arks
Mar
kP
arts
nam
eM
ark
Par
ts n
ame
CC
Cap
acito
r fo
r C
MT
hI-R
The
rmis
tor
CF
OC
apac
itor
for
FMO
Th
o-A
The
rmis
tor
CH
Cra
nkca
se h
eate
rT
ho
-DT
herm
isto
rC
MC
ompr
esso
r m
otor
Th
o-R
The
rmis
tor
Cn
A ~
WC
onne
ctor
( m
ark)
Tro
Tra
nsfo
rmer
CT
1C
urre
nt s
enso
rV
alV
aris
tor
FFu
seV
aoV
aris
tor
FM
IFa
n m
otor
(In
door
uni
t)20
S4-
way
val
ve s
olen
oid
FM
OFa
n m
otor
(O
utdo
or u
nit)
49F
IIn
tern
al th
erm
osta
t for
FM
IL
ED
1In
dica
tion
lam
p (G
reen
- R
un)
49F
OIn
tern
al th
erm
osta
t for
FM
oL
ED
2In
dica
tion
lam
p (Y
ellow
- Ti
mer
/Che
ck)
52C
Mag
netic
con
tact
or f
or C
ML
ML
ouve
r m
otor
52X
5, 6
Aux
iliar
y re
lay
NR
Surg
e su
ppre
ssor
X01
~07
Aux
iliar
y re
lay
PC
Phot
o co
uple
r63
H2
Hig
h pr
essu
re s
witc
h (f
or c
ontr
ol)
SV
1So
leno
id c
oil (
for
cont
rol)
vTe
rmin
al (
F)S
WSw
itch
(ON
/OFF
)■
Con
nect
orS
W3
Cha
ngeo
ver
switc
hL
ED
-GIn
dica
tion
lam
p (G
reen
)T
BTe
rmin
al b
lock
( m
ark)
LE
D-R
Indi
catio
n la
mp
(Red
)T
hI-A
The
rmis
tor
492
FDKN-H
Model FDKN258HEN-S1
Co
lor
mar
k
Mar
kC
olo
rB
KB
lack
BL
Blu
eB
RB
row
nG
RG
ray
OR
Ora
nge
PK
Pink
RD
Red
WH
Whi
teY
Yel
low
Mar
kC
olo
rB
K/R
DB
lack
/Red
BK
/WH
Bla
ck/W
hite
BL
/WH
Blu
e/W
hite
BR
/WH
Bro
wn/
Whi
teO
R/W
HO
rang
e/W
hite
RD
/WH
Red
/Whi
teY
/GN
Yel
low
/Gre
en
Po
wer
so
urc
e1
Ph
ase
220/
240V
50H
z
XR
3
XR
5
BK
BK
XR
1
Op
tio
n
Th
l-A
XR
2
XR
4
BK
BK
Th
l-R
BK
BK
BK
BK
BK
BK
Rec
eive
ram
p.
Wir
eles
sre
mo
teco
ntr
olle
r
LED
1
LED
2
TB
TB
52X5
FMI
(49F
I)
LM
SW
SW
3
CnCCnNCnH CnACnT
52X6
52X
552
X6
PC Cn
FC
nJ
Cn
QT
est
IC10
Val
RD
RD/W
H
BK/
WH
BK/
RD
BL/
WH
BR/
WH
Y/GN
WH
BK
BL
21 9 10 14
RD
21
4O
NO
FF
Pri
nte
d c
ircu
it b
oar
d3
BL
220/240V
PK
ORBR
RD
WHBLY
3
BR
Y/G
N
BK
DR
DR
Tho-
R
63H
2
Cn
L
LED
-R
LED
-G
(Ch
eck)
(Ru
n)
Cn
E
Vao(C
hec
ker) Cn
A1 T
roCn
A2
BK
Tho-
D
BK
Tho-
A
6
14V
27
BL/WH
BK/RD
BR/WH
BL
BL
P
P
BR
BR
BK
BK
2625
2120
1918
1716
1312
2
31
42
Pri
nte
d c
ircu
it b
oar
d
3
HL
UH
A1CF
01A2
28
X05
X02
X01
X03
X04
X06
X07
X01
220/240V
7
PC
PC
CnR
CnM1
CH
X04
X07
X02
X05
X03
X06
1 22/
N
33
44
55
F(3.15A)
OR/WH
OR/WH
ORORWHBRBLBK
WHWH
RDBL
Y/GN
WHRD
RD
BK
/WH
WH
CT
1
R
S
C
52C
Cc
RD/WH
RD
BK/WH
NTB
SV
152
C20
SFM
O1(4
9FO1
)
CM
Ou
tdo
or
Un
itIn
do
or
Un
it
BK
BK
NR
1L
Mea
nin
g o
f m
arks
Mar
kP
arts
nam
eM
ark
Par
ts n
ame
CC
Cap
acito
r fo
r C
MT
hI-R
The
rmis
tor
CF
OC
apac
itor
for
FMO
Th
o-A
The
rmis
tor
CH
Cra
nkca
se h
eate
rT
ho
-DT
herm
isto
rC
MC
ompr
esso
r m
otor
Th
o-R
The
rmis
tor
Cn
A ~
WC
onne
ctor
( m
ark)
Tro
Tra
nsfo
rmer
CT
1C
urre
nt s
enso
rV
alV
aris
tor
FFu
seV
aoV
aris
tor
FM
IFa
n m
otor
(In
door
uni
t)20
S4-
way
val
ve s
olen
oid
FM
OFa
n m
otor
(O
utdo
or u
nit)
49F
IIn
tern
al th
erm
osta
t for
FM
IL
ED
1In
dica
tion
lam
p (G
reen
- R
un)
49F
OIn
tern
al th
erm
osta
t for
FM
oL
ED
2In
dica
tion
lam
p (Y
ellow
- Ti
mer
/Che
ck)
52C
Mag
netic
con
tact
or f
or C
ML
ML
ouve
r m
otor
52X
5, 6
Aux
iliar
y re
lay
NR
Surg
e su
ppre
ssor
X01
~07
Aux
iliar
y re
lay
PC
Phot
o co
uple
r63
H2
Hig
h pr
essu
re s
witc
h (f
or c
ontr
ol)
SV
1So
leno
id c
oil (
for
cont
rol)
vTe
rmin
al (
F)S
WSw
itch
(ON
/OFF
)■
Con
nect
orS
W3
Cha
ngeo
ver
switc
hL
ED
-GIn
dica
tion
lam
p (G
reen
)T
BTe
rmin
al b
lock
( m
ark)
LE
D-R
Indi
catio
n la
mp
(Red
)T
hI-A
The
rmis
tor
493
FDKN-H
Model FDKNP208HEN-S
Co
lor
mar
k
Mar
kC
olo
rB
KB
lack
BL
Blu
eB
RB
row
nG
RG
ray
OR
Ora
nge
PK
Pink
RD
Red
WH
Whi
teY
Yel
low
Mar
kC
olo
rB
K/R
DB
lack
/Red
BK
/WH
Bla
ck/W
hite
BL
/WH
Blu
e/W
hite
BR
/WH
Bro
wn/
Whi
teO
R/W
HO
rang
e/W
hite
RD
/WH
Red
/Whi
teY
/GN
Yel
low
/Gre
en
Po
wer
so
urc
e1
Ph
ase
220/
240V
50H
z
XR
3
XR
5
BK
BK
XR
1
Op
tio
n
Th
l-A
XR
2
XR
4
BK
BK
Th
l-R
BK
BK
BK
BK
BK
BK
Rec
eive
ram
p.
Wir
eles
sre
mo
teco
ntr
olle
r
LED
1
LED
2
TB
TB
52X5
FMI
(49F
I)
LM
SW
SW
3
CnCCnNCnH CnACnT
52X6
52X
552
X6
PC
Cn
FC
nJ
Cn
QT
est
RD
RD/W
H
BK/
WH
BK/
RD
BL/
WH
BR/
WH
Y/GN
WH
BK
BL
21 9 10 14
RD
21
4O
NO
FF
Pri
nte
d c
ircu
it b
oar
d3
BLPK
ORBR
RD
WHBLY
3
BR
Y/G
N
BK
DR
DR
Tho-
R
63H
2
Cn
L
LED
-R
LED
-G
(Ch
eck)
(Ru
n)
Cn
E
Vao(C
hec
ker) Cn
A1 T
roCn
A2
BK
Tho-
D
BK
Tho-
A
6
14V
27
BL/WH
BK/RD
BR/WH
BL
BL
P
P
BR
BR
BK
BK
2625
2120
1918
1716
1312
2
31
42
Pri
nte
d c
ircu
it b
oar
d
3
HL
UH
A1CF
01A2
28
X05
X02
X01
X03
X04
X06
X07
X01
220/240V
7
PC
PC
CnR
CnM1
CH
X04
X07
X02
X05
X03
X06
BR
BR63H
1
89
1 22/
N
33
44
55
F(3.15A)
OR/WH
OR/WH
ORORWHBRBLBK
WHWH
RDBL
Y/GN
WHRD
RD
BK
/WH
WH
CT
1
R
S
C
52C
Cc
RD/WH
RD
BK/WH
NTB
SV
152
C20
SFM
O1(4
9FO1
)
CM
Val
BKRD
BKBR
CnW1
CnW2
TrI
220/240V
14V
16V
Ou
tdo
or
Un
itIn
do
or
Un
it
BK
BK
NR
L1
Mea
nin
g o
f m
arks
Mar
kP
arts
nam
eM
ark
Par
ts n
ame
CC
Cap
acito
r fo
r C
MT
hI-R
The
rmis
tor
CF
OC
apac
itor
for
FMO
Th
o-A
The
rmis
tor
CH
Cra
nkca
se h
eate
rT
ho
-DT
herm
isto
rC
MC
ompr
esso
r m
otor
Th
o-R
The
rmis
tor
Cn
A ~
WC
onne
ctor
( m
ark)
Tro
Tra
nsfo
rmer
CT
1C
urre
nt s
enso
rV
alV
aris
tor
FFu
seV
aoV
aris
tor
FM
IFa
n m
otor
(In
door
uni
t)20
S4-
way
val
ve s
olen
oid
FM
OFa
n m
otor
(O
utdo
or u
nit)
49F
IIn
tern
al th
erm
osta
t for
FM
IL
ED
1In
dica
tion
lam
p (G
reen
- R
un)
49F
OIn
tern
al th
erm
osta
t for
FM
oL
ED
2In
dica
tion
lam
p (Y
ellow
- Ti
mer
/Che
ck)
52C
Mag
netic
con
tact
or f
or C
ML
ML
ouve
r m
otor
52X
5, 6
Aux
iliar
y re
lay
NR
Surg
e su
ppre
ssor
PC
Phot
o co
uple
rX
01~0
7A
uxili
ary
rela
y63
H1
Hig
h pr
essu
re s
witc
h (f
or p
rote
ctio
n)S
V1
Sole
noid
coi
l (fo
r co
ntro
l)63
H2
Hig
h pr
essu
re s
witc
h (f
or c
ontr
ol)
SW
Switc
h (O
N/O
FF)
vTe
rmin
al (
F)S
W3
Cha
ngeo
ver
switc
h■
Con
nect
orT
BTe
rmin
al b
lock
( m
ark)
LE
D-G
Indi
catio
n la
mp
(Gre
en)
Th
I-AT
herm
isto
rL
ED
-RIn
dica
tion
lam
p (R
ed)
494
FDKN-H
Model FDKNP258HEN-S
Po
wer
so
urc
e1
Ph
ase
220/
240V
50H
z
XR
3
XR
5
BK
BK
XR
1
Op
tio
n
Th
l-A
XR
2
XR
4
BK
BK
Th
l-R
BK
BK
BK
BK
BK
BK
Rec
eive
ram
p.
Wir
eles
sre
mo
teco
ntr
olle
r
LED
1
LED
2
TB
TB
52X5
FMI
(49F
I)
LM
SW
SW
3
CnCCnNCnH CnACnT
52X6
52X
552
X6
PC Cn
FC
nJ
Cn
QT
est
IC10
Val
RD
RD/W
H
BK/
WH
BK/
RD
BL/
WH
BR/
WH
Y/GN
WH
BK
BL
21 9 10 14
RD
21
4O
NO
FF
Pri
nte
d c
ircu
it b
oar
d3
BL
220/240V
PK
ORBR
RD
WHBLY
3
BR
Y/G
N
BK
DR
DR
Tho-
R
63H
2
Cn
L
LED
-R
LED
-G
(Ch
eck)
(Ru
n)
Cn
E
Vao(C
hec
ker) Cn
A1 T
roCn
A2
BK
Tho-
D
BK
Tho-
A
6
14V
27
BL/WH
BK/RD
BR/WH
BL
BL
P
P
BR
BR
BK
BK
2625
2120
1918
1716
1312
2
31
42
Pri
nte
d c
ircu
it b
oar
d
3
HL
UH
A1CF
01A2
28
X05
X02
X01
X03
X04
X06
X07
X01
220/240V
7
PC
PC
CnR
CnM1
CH
X04
X07
X02
X05
X03
X06
BR
BR63H
1
89
1 22/
N
33
44
55
F(3.15A)
OR/WH
OR/WH
ORORWHBRBLBK
WHWH
RDBL
Y/GN
WHRD
RD
BK
/WH
WH
CT
1
R
S
C
52C
Cc
RD/WH
RD
BK/WH
NTB
SV
152
C20
SFM
O1(4
9FO1
)
CM
Ou
tdo
or
Un
itIn
do
or
Un
it
BK
BK
NR
L1
Co
lor
mar
k
Mar
kC
olo
rB
KB
lack
BL
Blu
eB
RB
row
nG
RG
ray
OR
Ora
nge
PK
Pink
RD
Red
WH
Whi
teY
Yel
low
Mar
kC
olo
rB
K/R
DB
lack
/Red
BK
/WH
Bla
ck/W
hite
BL
/WH
Blu
e/W
hite
BR
/WH
Bro
wn/
Whi
teO
R/W
HO
rang
e/W
hite
RD
/WH
Red
/Whi
teY
/GN
Yel
low
/Gre
en
Mea
nin
g o
f m
arks
Mar
kP
arts
nam
eM
ark
Par
ts n
ame
CC
Cap
acito
r fo
r C
MT
hI-R
The
rmis
tor
CF
OC
apac
itor
for
FMO
Th
o-A
The
rmis
tor
CH
Cra
nkca
se h
eate
rT
ho
-DT
herm
isto
rC
MC
ompr
esso
r m
otor
Th
o-R
The
rmis
tor
Cn
A ~
WC
onne
ctor
( m
ark)
Tro
Tra
nsfo
rmer
CT
1C
urre
nt s
enso
rV
alV
aris
tor
FFu
seV
aoV
aris
tor
FM
IFa
n m
otor
(In
door
uni
t)20
S4-
way
val
ve s
olen
oid
FM
OFa
n m
otor
(O
utdo
or u
nit)
49F
IIn
tern
al th
erm
osta
t for
FM
IL
ED
1In
dica
tion
lam
p (G
reen
- R
un)
49F
OIn
tern
al th
erm
osta
t for
FM
oL
ED
2In
dica
tion
lam
p (Y
ellow
- Ti
mer
/Che
ck)
52C
Mag
netic
con
tact
or f
or C
ML
ML
ouve
r m
otor
52X
5, 6
Aux
iliar
y re
lay
NR
Surg
e Su
ppre
ssor
X01
~07
Aux
iliar
y re
lay
PC
Phot
o co
uple
r63
H1
Hig
h pr
essu
re s
witc
h (f
or P
rote
ctio
n)S
V1
Sole
noid
coi
l (fo
r co
ntro
l)63
H2
Hig
h pr
essu
re s
witc
h (f
or c
ontr
ol)
SW
Switc
h (O
N/O
FF)
vTe
rmin
al (
F)S
W3
Cha
ngeo
ver
switc
h■
Con
nect
orT
BTe
rmin
al b
lock
( m
ark)
LE
D-G
Indi
catio
n la
mp
(Gre
en)
Th
I-AT
herm
isto
rL
ED
-RIn
dica
tion
lam
p (R
ed)
495
FDKN-H
Model FDKNP308HEN-S
Po
wer
so
urc
e1
Ph
ase
220/
240V
50H
z
XR
3
XR
5
BK
BK
XR
1
Op
tio
n
Th
l-A
XR
2
XR
4
BK
BK
Th
l-R
BK
BK
BK
BK
BK
BK
Rec
eive
ram
p.
Wir
eles
sre
mo
teco
ntr
olle
r
LED
1
LED
2
TB
TB
52X5
FMI
(49F
I)
LM
SW
SW
3
CnCCnNCnH CnACnT
52X6
52X
552
X6
PC Cn
FC
nJ
Cn
QT
est
IC10
Val
RD
RD/W
H
BK/
WH
BK/
RD
BL/
WH
BR/
WH
Y/GN
WH
BK
BL
21 9 10 14
RD
21
4O
NO
FF
Pri
nte
d c
ircu
it b
oar
d3
BL
220/240V
PK
ORBR
RD
WHBLY
3
BR
Y/G
N
BK
DR
DR
Tho-
R
63H
2
Cn
L
LED
-R
LED
-G
(Ch
eck)
(Ru
n)
Cn
E
Vao(C
hec
ker) Cn
A1 T
roCn
A2
BK
Tho-
D
BK
Tho-
A
6
14V
27
BL/WH
BK/RD
BR/WH
BL
BL
BL
BL
P
P
BR
BR
BK
BK
2625
2322
2120
1918
1716
1312
2
31
42
Pri
nte
d c
ircu
it b
oar
d
3
HL
UH
A1CF
01A2
28
X05
X02
X01
X03
X04
X06
X08
X07
X01
220/240V
7
PC
PC
CnR
CnM1
CH
X04
X07
X02
X05
X08
X03
X06
BR
BR63H
1
89
1 22/
N
33
44
55
F(3.15A)
OR/WH
OR/WH
ORORWHBRBLBK
WHWH
RDBL
Y/GN
WHRD
RD
BK
/WH
WH
CT
1
R
S
C
52C
Cc
RD/WH
RD
BK/WH
NTB
SV
2S
V1
52C
20S
FMO1
(49F
O1)
CM
BK
BK
NR
1L
Ind
oo
r U
nit
Ou
tdo
or
Un
it
Co
lor
mar
k
Mar
kC
olo
rB
KB
lack
BL
Blu
eB
RB
row
nG
RG
ray
OR
Ora
nge
PK
Pink
RD
Red
WH
Whi
teY
Yel
low
Mar
kC
olo
rB
K/R
DB
lack
/Red
BK
/WH
Bla
ck/W
hite
BL
/WH
Blu
e/W
hite
BR
/WH
Bro
wn/
Whi
teO
R/W
HO
rang
e/W
hite
RD
/WH
Red
/Whi
teY
/GN
Yel
low
/Gre
en
Mea
nin
g o
f m
arks
Mar
kP
arts
nam
eM
ark
Par
ts n
ame
CC
Cap
acito
r fo
r C
MT
hI-R
The
rmis
tor
CF
OC
apac
itor
for
FMO
Th
o-A
The
rmis
tor
CH
Cra
nkca
se h
eate
rT
ho
-DT
herm
isto
rC
MC
ompr
esso
r m
otor
Th
o-R
The
rmis
tor
Cn
A ~
WC
onne
ctor
( m
ark)
Tro
Tra
nsfo
rmer
CT
1C
urre
nt s
enso
rV
alV
aris
tor
FFu
seV
aoV
aris
tor
FM
IFa
n m
otor
(In
door
uni
t)20
S4-
way
val
ve s
olen
oid
FM
OFa
n m
otor
(O
utdo
or u
nit)
49F
IIn
tern
al th
erm
osta
t for
FM
IL
ED
1In
dica
tion
lam
p (G
reen
- R
un)
49F
OIn
tern
al th
erm
osta
t for
FM
oL
ED
2In
dica
tion
lam
p (Y
ellow
- Ti
mer
/Che
ck)
52C
Mag
netic
con
tact
or f
or C
ML
ML
ouve
r m
otor
52X
5, 6
Aux
iliar
y re
lay
NR
Surg
e su
ppre
ssor
X01
~8A
uxili
ary
rela
yP
CPh
oto
coup
ler
63H
1H
igh
pres
sure
sw
itch
(for
pro
tect
ion)
SV
1, 2
Sole
noid
coi
l (fo
r co
ntro
l)63
H2
Hig
h pr
essu
re s
witc
h (f
or c
ontr
ol)
SW
Switc
h (O
N/O
FF)
vTe
rmin
al (
F)S
W3
Cha
ngeo
ver
switc
h■
Con
nect
orT
BTe
rmin
al b
lock
( m
ark)
LE
D-G
Indi
catio
n la
mp
(Gre
en)
Th
I-AT
herm
isto
rL
ED
-RIn
dica
tion
lam
p (R
ed)
496
FDKN-H
Model FDKNP308HES-S
Po
wer
so
urc
e3
Ph
ase
380/
415V
50H
z
XR
3
XR
5
BK
BK
XR
1
Op
tio
n
Th
l-A
XR
2
XR
4
BK
BK
Th
l-R
BK
BK
BK
BK
BK
BK
Rec
eive
ram
p.
Wir
eles
sre
mo
teco
ntr
olle
r
LED
1
LED
2
TB
52X5
FMI
(49F
I)
LM
SW
SW
3
CnCCnNCnH CnACnT
52X6
52X
552
X6
PC Cn
FC
nJ
Cn
QT
est
IC10
Val
RD
WH
BK
BL
21 9 10 14
RD
21
4O
NO
FF
Pri
nte
d c
ircu
it b
oar
d3
BL
220/240V
PK
ORBR
RD
WHBLY
3
BR
Y/G
N
1 2 3 4 5
TB
RD
/WH
BK
/WH
BK
/RD
BL
/WH
BR
/WH
Y/GN
BK
DR
DR
Tho
-R
63H
2
CnL
LED
-R
LED
-G
(Che
ck)
(Run
)
CnE
Vao(C
heck
er)
CnA
1 TroC
nA2
BK
Tho
-D
BK
Tho
-A
6
14V
27
BL/WH
BK/RD
BR/WH
BL
BL
BL
BL
P
P
BR
BR
BK
BK
2625
2322
2120
1918
1716
1312
21
13
24
5 6
Prin
ted
circ
uit b
oard
3
HL
UH
A1
CF
01A
2
28
X05
X02
X01
X03
X04
X06
X08
X07
X01
220/240V
7
PC
PC
CnR
CnM1
CH
X04
X07
X02
X05
X08
X03
X06
BR
BR63H
1
89
2/N 3 4 5
F(3.15A)
OR/WH
OR/WH
ORORWHBRBLBK
BL
RD
Y/GN
WH WH
BL
RD
WH
BL
BK
/WH
RD
CT
2C
T1
V
UW
52C
RD/WH
RD
BK/WH
WH
L3 NL2TB
SV
2S
V1
52C
20S
FMO
1(4
9FO
1)
CM
BK
BKN
R
1L1
Ind
oo
r U
nit
Ou
tdo
or
Un
it
Co
lor
mar
k
Mar
kC
olo
rB
KB
lack
BL
Blu
eB
RB
row
nG
RG
ray
OR
Ora
nge
PPi
nkR
DR
edW
HW
hite
Mar
kC
olo
rB
K/R
DB
lack
/Red
BK
/WH
Bla
ck/W
hite
BL
/WH
Blu
e/W
hite
BR
/WH
Bro
wn/
Whi
teO
R/W
HO
rang
e/W
hite
RD
/WH
Red
/Whi
teY
/GN
Yel
low
/Gre
en
Mea
nin
g o
f m
arks
Mar
kP
arts
nam
eM
ark
Par
ts n
ame
CF
IC
apac
itor
for
FMI
Th
I-RT
herm
isto
rC
FO
1C
apac
itor
for
FMO
Th
o-A
The
rmis
tor
CH
Cra
nkca
se h
eate
rT
ho
-DT
herm
isto
rC
MC
ompr
esso
r m
otor
Th
o-R
The
rmis
tor
Cn
A ~
ZC
onne
ctor
( m
ark)
TrO
Tra
nsfo
rmer
(O
utdo
or u
nit)
CT
1,2
Cur
rent
sen
sor
Val
Var
isto
rF
Fuse
Vao
Var
isto
rF
MI
Fan
mot
or (
Indo
or u
nit)
20S
4-w
ay v
alve
sol
enoi
dF
MO
1Fa
n m
otor
(O
utdo
or u
nit)
49F
IIn
tern
al th
erm
osta
t for
FM
I
LE
D1
Indi
catio
n la
mp
(Gre
en-R
un)
49F
O1
Inte
rnal
ther
mos
tat f
or F
Mo
LE
D2
Indi
catio
n la
mp
(Yel
low
-Tim
er/C
heck
)52
CM
agne
tic c
onta
ctor
for
CM
LM
Louv
er m
otor
52X
5, 6
Aux
iliar
y re
lay
NR
Surg
e su
ppre
ssor
X01
~08
Aux
iliar
y re
lay
PC
Phot
o co
uple
r63
H1
Hig
h pr
essu
re s
witc
h (f
or p
rote
ctio
n)S
V1,
2So
leno
id c
oil (
for
cont
rol)
63H
2H
igh
pres
sure
sw
itch
(for
con
trol
)S
WSw
itch
(ON
/OFF
)v
Term
inal
(F)
SW
3C
hang
eove
r sw
itch
■C
onne
ctor
TB
Term
inal
blo
ck (
mar
k)L
ED
-GIn
dica
tion
lam
p (G
reen
)T
hI-A
The
rmis
tor
LE
D-R
Indi
catio
n la
mp
(Red
)
497
FDKN-H
12.5 APPLICATION DATASAFETY PRECAUTIONS
• Please read these “Safety Precautions” first then accurately execute the installation work.• Though the precautionary points indicated herein are divided under two headings. WARNING and CAUTION , those points
which are related to the strong possibility of an installation done in error resulting in death or serious injury are listed in the WARNINGsection. However, there is also a possibility of serious consequences in relationship to the points listed in the CAUTION section aswell.In either case, important safety related information is indicated, so by all means, properly observe all that is mentioned.
• After completing the installation, along with confirming that no abnormalities were seen from the operation tests, please explainoperating methods as well as maintenance methods to the user (customer) of this equipment, based on the owner’s manual.Moreover, ask the customer to keep this sheet together with the owner’s manual.
WARNING
CAUTION
• This system should be applied to places of office, restaurant, residence and the like. Application to inferiorenvironment such as engineering shop could cause equipment malfunction.
• Please entrust installation to either the company which sold you the equipment or to a professional contractor.Defects from improper installations can be the cause of water leakage, electric shocks and fires.
• Execute the installation accurately, based on following the installation manual. Again, improper installations canresult in water leakage, electric shocks and fires.
• When a large air-conditioning system is installed to a small room, it is necessary to have a prior planned counter-measure for the rare case of a refrigerant leakage, to prevent the exceeding of threshold concentration.In regards to preparing this countermeasure, consult with the company from which you perchased the equipment,and make the installation accordingly. In the rare event that a refrigerant leakage and exceeding of thresholdconcentration does occur, there is the danger of a resultant oxygen deficiency accident.
• For installation, confirm that the installation site can sufficiently support heavy weight. When strength is insufficient,injury can result from a falling of the unit.
• Execute the prescribed installation construction to prepare for earthquakes and the strong winds of typhoons andhurricanes, etc. Improper installations can result in accidents due to a violent falling over of the unit.
• For electrical work, please see that a licensed electrician executes the work while following the safety standardsrelated to electrical equipment, and local regulations as well as the installation instructions, and that only exclusiveuse circuits are used.Insufficient power source circuit capacity and defective installment execution can be the cause of electric shocksand fires.
• Accurately connect wiring using the proper cable, and insure that the external force of the cable is not conductedto the terminal connection part, through properly securing it. Improper connection or securing can result in heatgeneration or fire.
• Take care that wiring does not rise upward, and accurately install the lid/service panel. Its improper installationcan also result in heat generation or fire.
• When setting up or moving the location of the air-conditioner, do not mix air etc. or anything other than thedesignated refrigerant (R22) within the refrigeration cycle.Rupture and injury caused by abnormal high pressure can result from such mixing.
• Always use accessory parts and authorized parts for installation construction. Using parts not authorized by thiscompany can result in water leakage, electric shock, fire and refrigerant leakage.
• Execute proper grounding. Do not connect the ground wire to a gas pipe, water pipe, lightning rod or a telephoneground wire. Improper placement of ground wires can result in electric shock.
• The installation of an earth leakage breaker is necessary depending on the established location of the unit. Notinstalling an earth leakage breaker may result in electric shock.
• Do not install the unit where there is a concern about leakage of combustible gas.The rare event of leaked gas collecting around the unit could result in an outbreak of fire.
• For the drain pipe, follow the installation manual to insure that it allows proper drainage and thermally insulate itto prevent condensation. Inadequate plumbing can result in water leakage and water damage to interior items.
12.4 OUTLINE OF OPERATION CONTROL BY MICROCOMPUTERSame as the cooling/heating equipment for FDT (N) heat pump type. Refer to page 317.
498
FDKN-H
(a) Select the installation location that meets the following conditions and obtain
the customer's consent.
1) Location where cold and warm air spread all over the room
2) Location where piping and wiring to the outdoors can easily be laid down.
3) Location where the drain can be discharged completely.
4) Location where the wall to mount the unit is rigid.
5) Location where there is no wind obstruction to the return air and supply
air grills.
6) Location not exposed to direct sunshine.
7) Avoid the location exposed to oil splash or vapor.
8) Avoid the location near to the machine emitting high-frequency radio wave.
9) Avoid the location where the receiver of remote control is subject to
strong illumination.
10) Select the location where the unit can securely be operated by the wire-
less remote controller referring to the Article “Effective distance of wire-
less remote controller” indicated at the backside.
11) Secure the space for inspection and maintenance work.
Unit: mm
120 or more 120 or more
Floor
1 m
Wireless remote con-troller
2 m
Within 5 m
Illumination over suction grill-800 lus.
Within30°
Within
30°
Within 60°
Within 5 m
Relation between illumination at receiverunit and operating distance
Caution item for close installation ofmultiple units
(Plan view)
3 m
5 m
7.5
m
720 l
ux
360 lux
180 lux
60°
(Plan view)
5 m 5 m
60° 60°
[Condition] Illumination at suction grill face 800 lux
A
Effective scope Effective scope
12.5.1 Installation of indoor unitNOTICE
All Wiring of this installation must comply with NATIONAL, STATE AND LOCAL REGULATIONS. These instructionsdo not cover all variations for every kind of installation circumstance. Should further information be desired or shouldparticular problems occur, the matter should be referred to Mitsubishi Heavy Industries, Ltd. through your local distributor.
WARNINGBE SURE TO READ THESE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. FAILURE TOFOLLOW THESE INSTRUCTIONS COULD CAUSE SERIOUS INJURY OR DEATH, EQUIPMENT MALFUNCTIONAND/OR PROPERTY DAMAGE.
(2) Cautions for use of wireless remote controller(a) Opareting distance of wireless remote controller
(b) Cautlons for operation
1) Orient the remote control switch properly toward the receiver of the unit.
2) Operating distance is as shown above but it may vary largely depending on the conditions.
3) Effective distance may be shortened and the receiving may be disturbed when the receiver is under the condition of
direct exposure to sunlight or other strong light like electric bulb, dust is accumulated on it and it is shielded with a
curtain, etc.
or m
ore
(1) Selection of installation location
DimensionFDKN208 type FDKN258 · 308 type
A 65 90
499
FDKN-H
(3) Carry-in and installation of unit(a) Carry-in
1) When carrying in the unit, carry it in as packed to the installation site as near as possible.2) If you are compelled to carry in the unit unpacked, cover it with a nylon sling so that it is not
damaged.Note) Do not carry the unit by holding it at the supply air louver.
3) When laying the unit on the ground after unpacking. place it with its front side up without fail.(b) Attaching of mounting plate
1) The indoor unit weighs approx, 11 kg. Therefore, check whether the portion to install the unit can bear the weight ofunit. If it seems to be danger, reinforce the portion by a plate or a beam before installing the unit. It is not allowed toinstall the unit directly on the wall. Whenever you install the unit, use the attached mounting plate.
For left rear take-out piping For right rear take-out piping
1. Remove the drain hose. 2. Remove the drain cap. 3. Insert the drain cap. 4. Connect the drain hose.
Reference hole
WARNING
The indoors
Wall
The outdoors
Sleeve
Sealing plate
Sleeve
Piping
Drain hose
Level matching mark
For left running horizontal piping For right running horizontal piping
For left running horizontal piping For right running horizontal piping
This air-conditioner is so constructed that dew generated on thebackside is gathered in the drain pan to drain, therefore, do notstore the power cable, etc. at the higher place than the trough.
Trough
Wall
Wiring storage portion
Right
Rear
Down Left rearLeft
• Find structural members (Intermediate pillar, etc.) suitable for mounting the unit,then install the unit firmly while checking levelness.
A
• Adjust the level of mounting plate under the condi-tion that four screws are tightened temporarily.
• Turn the mounting plate around the reference holeto adjust the levelness.
• Install the unit where it can bear the weight with sufficient strength margin. In the case ofinsufficient strength or insufficient installation work, the unit may fall and cause injury.
After forming ofpiping and be-fore tape wind-ing, confirm thatthe connectingwire is securelyfixed to the ter-minal table.
The piping can be taken out from therear, left, left rear, right and down.
• Make a downgrade (5°) from the indoors toward the outdoors.
(c) Procedure for making hole on the wall
(d) Forming of piping and drain hose1) Rear take out case• Forming of piping • Tape winding
• Hold the root portion of pip-ing, change the direction thenexpand and make forming.
• Wind the tape on the portion which passesthrough the hole on the wall.
• Always make taping on the wiring whichcrosses with the piping, if any.
2) Cautions for left take-out and rear take-out casea) Looking down
b) Procedure for changing drain hose
• Loosen spring type clamp toremove.
• Remove by hand or pliers. • Insert the drain cap which wasremoved in procedure 2 se-curely using a hexagonalwrench, etc.
Note: When it is not inserted se-curely, water leakage mayoccur.
• Loosen the spring type clampto insert the drain hose se-curely.
Note: When it is not inserted se-curely, water leakage mayoccur.
ModelFDKN208 · 258 type FDKN308 typeDimension
A 450 690
500
FDKN-H
ø27.
5
ø16.
4ø1
2.4
(e) Installation of unit
Lid (right hand)
Mounting plate
Wall
Claw at the lower portion of indoor unit base.
Indoor unit
Mounting plate
Installation work procedure
(1) Hang the upper portion of in-door unit on the mounting plate.
(2) The indoor unit can be fixedwith one action by pushing itslower portion slightly.
Illustration showing the end of drain hose
No chevron-shaped bend is allowed.
No trap is allowed.
The end shallnot be sub-merged in wa-ter.
Hard vinyl chloride pipe (general-purposepipe VP-16) can be connected.
CAUTION
The drainage work must be performed surely and the
drainage must be checked. If drainage is not perfect, it
causes water leakage.
• To remove the unit from themounting plate, remove theright and left lids then removethe claw at the lower portionof base.
(4) Refrigerant piping
(a) Comply the following table for the tightening torque of the flared nut and flange bolt.
Flared nut tightening torque
φ6.35: 16 to 20 (N-m), (1.6 to 2.0 kg-m)
φ9.52: 40 to 50 (N-m), (4 to 5 kg-m)
φ15.88: 90 to 120 (N-m), (9 to 12 kg-m)
Wrap the gaseous refrigerant piping and liquid refrigerant piping with thermal insulator perfectly.
(b) In the case of liquid refrigerant piping, if it is not insulated, dew condensation and water leakage may occur.
(c) When removing the flared nut at the piping end of unit, always use 2 of spanners, and when
connecting the pipe tighten it firmly using 2 of spanners.
(d) When connecting the flared nut, apply refrigerating machine oil on the back surface of flare
and screw-in the nut for the first 3 to 4 turns by hand.
(e) Use the pipe made of the following material. It is very convenient to use the separately sold
piping kit.
Material: Phosphor deoxidized seamless copper tube (C1220T,JIS H3300)
(f) Cover the connection part with indoor unit insulation material and insulate the notched part
with attached insulation and then wrap it up with tape.
(6) Fixing of wiring
(a) Remove the front panel.
(b) Connect the wire from the indoor and outdoor units to the terminal table of control box.
(c) Attach the front panel.
Notes (1) Refer to the illustration below for the removal and attaching of the front panel.
(2) Before connecting the wiring to the terminal table, confirm the terminal number.
Arrange so that thecut portion is lo-cated upper side.
Vinyl tape
Insulate with attached in-sulation.
(5) Drain piping
(a) Lay the drain piping with downgrade to facilitate flow of drain,and do not make a trap or chevron-shaped bend. (The drain
piping can be taken out from the unit to the left, right, rear and down direction.)
Wrap the thermal insulator on the hard vinyl chloride pipe (VP-16) laid in the room.
(b) Pour water into the drain pan below the heat exchanger to
check that water is drained outdoors.
Claw (2 places)(FDKN308: 3 places)
501
FDKN-H
(d) Removal order of the panel
1) Open the return air grill. (Pull both lower ends of the return air grill, raise the grill until the reaction is felt after
disengaging the latch. The return air grill will stop at approx. 60° open position.)
2) Remove the air filter.
3) Remove 2 fixing screws for model 258 and 3 fixing screws for model 308.
4) Close the return air grill. (Hold both lower ends of the return air grill, lower the grill slowly downward, push it slightly
to engage the latch and again push the center portion slightly.)
5) Remove the fixing screw of front panel. (2 places for 208, 3 places for 258, and 4 places for 308.)
6) Lift the lower portion of front panel this side and remove it while pushing the upper portion up.
(e) Attaching order of the panel
1) Lay the front panel on the main body.
2) Push the "O" portion shown in the illustration from front side.
3) Tighten the fixing screw of front panel.
4) Open the return air grill to tighten the cap screw. (258, 308 only)
5) Set the air filter.
6) Close the return air grill.
Push in these portions.Fixing screw
Fixing screwBy switching the dip switch (SW3-3) on the indoor unit printed circuitboard ("Specify the following switch number."), the operation mode canbe changed to the quiet mode (mild mode). Confirm at installation andchange if necessary.
12.5.2 Installation of outdoor unitSame as the cooling/heating equipment for FDT (N) heat pump type.
Refer to page 338.
12.6 MAINTENANCE DATASame as the cooling/heating equipment for FDT (N) heat pump type.
Refer to page 348.
208 has no screws. 258 has 2places and 308 has 3 places.( )
258 has 3 places and308 has 4 places.( )