fast guide c4ops fast guide - silynx communicationsfast guide - doc-usm000011 - rev 06, april 2015...
TRANSCRIPT
20M H20 DIVABLE CONFIG
Acoustic Tube for Covert Monitoring
CONNECTING EARMUFFS
Helmet Clip
C4OPS Control Box
Peltor/ Sordin Headset Adaptor P/N: CA0015-01
Earmuff
NOTE: Prior to diving, disconnect all other radio adaptors and attach diving caps.
Tighten battery cover
Acoustic Tube
Helmet Clip
Headband
C4OPS Maritime Headset Config (P/N: SHS0003-17)
The C4OPS System configured with the C4OPS Maritime Headset Config (P/N: SHS0003-17) and MBITR 10 pin radio adaptor (P/N: CA0035-00) is 20m immersible.
CONFIGURATION NOTICE: This document contains operational informa-tion related to the Silynx C4OPS® Headset. The information contained here-in is for the operation and support of the C4OPS® Headset.
PROPRIETARY NOTICE: This document contains information that is pro-prietary to Silynx Communications, Inc. It is furnished solely for operation and support purposes and is not provided for reprocurement purposes. All reprocurement and manufacturing rights are expressly reserved by Silynx Communications, Inc. and no such use may be made of this document, either directly or indirectly, without the prior written consent of an authorized official of Silynx Communications, Inc.
SILYNX COMMUNICATIONS, INC PUBLISHED AND CONFIDENTIAL WORK Fast Guide - DOC-USM000011 - Rev 06, April 2015 ALL RIGHTS RESERVED COPYRIGHT:
www.silynxcom.com 1.866.325.1731 | [email protected]
9901 Belward Campus Drive Suite 150 Rockville, MD 20850
FAST GUIDE
MBITR 10 pin radio adaptor (P/N: CA0035-00)
Micro C4OPS External Battery Compartment (P/N: CA0234-00)
C4OPSMICRO C4OPS
MBITR 10 pin radio adaptor (P/N: CA0035-00)
FAST GUIDEC4OPS
PROTECTION FROM WITHIN
SETTING UP OPERATING C4OPS® BASIC FUNCTIONS
(+) Volume
(-) Volume
Secondary PTT
“Pairing Successful”“Pairing Activated”
Beeps 30 sec
NOTE: If “Pairing Failed” repeat the steps above.
(-) Hear Thru Low Sensitivity/ Hear Thru Off
(+) Hear Thru High Sensitivity
(1) Press & hold
(2) Press & hold pairing keys 3 sec
PAIRING DUAL WIRELESS PTT [DWPTT]
HEAR THRU LEVEL VOLUME LEVEL
Off/ On/ Volume Level
High Sensitivity
Low Sensitivity/ Hear Thru Off
NOTE: In windy conditions reduce “Hear Thru”
CHANNEL SELECTION VOICE PROMPT VOLUME LEVEL
EXTRAS
(2) Press & hold 3 sec to confirm (2) (+) Volume
(2) (-) Volume(2) Press & hold 3 sec to confirm
(1) Press until you hear “Channel Selection”
(1) Press until you hear “Voice Prompt Level”
Press & hold 3 sec “Extras”
In high noise, such as aircraft/vehicles, you may hear whistling. Press (-) until the sound disappears. If the problem continues, reinsert the ear buds and make sure you pass the sealing test.
TROUBLESHOOTING:
MOUNTING THE CONTROL BOX
Molle Clip
Zipties
Zipties
*1.5V AA Lithium battery NOTE: No battery needed if using MBITR side connector.
Peltor/ Sordin Headset Adaptor Maritime Headset Config
Secondary Radio Lead
Connect
Intercom Cable Adaptor
Connect
Attach
Tighten
(1) Connect
C4OPS Control Box
C4OPS In Ear Headset
Headband Boom Mic
Ops Core Chinstrap Boom Mic
Basic In Ear Headset (Blocked Connector)
Hybrid Headset (Boom Mic Connector)
(2)
(6) (3)
(4)
(5)
Rotary Knob Off/ On/ Volume Level
Primary PTT
Secondary PTT
PTT3 / Hot Key
(+)
(-)
Mode
C4OPS CONTROLS
EAR BUD LEAK TEST
INSERTING EAR BUDS
Shell Ear Retainers Keep mic exposed
Attach collar clip. Hang In Ear Headset on your ear.
Squash foam ear plug.
Pull upper ear up and back and push the ear bud firmly into the canal.
Press ear bud until foam ear plug expands.
Tighten nape slider. Position ear retainer.
“Leak Right”
“Leak Left”
Leak = Reinsert ear plugs / replace ear plug size.
OR
No = Pass
“C4OPS 2X Beep”
(1) Turn MBITR on. Enable MBITR side
connector.
(2) Turn C4OPS on.
“Leak Both”VP
VP
(3) MBITR is auto set to external audio and
keypad locked.
(4) Ear plug sealing test will begin.
(5)
Primary Radio Lead
GETTING STARTED
Primary PTT
VP = Voice Prompt = Important
*