fac 858 i/wp/ir-s/-hs fa 857 i/wp/ir - funkwerkfac 858 i/wp/ir-s/-hs . fa 857 i/wp/ir . operating...

FAC 858 I/WP/IR-S/-HS

FA 857 I/WP/IR Operating Instructions

Funkwerk video systeme GmbH Thomas-Mann-Str. 50 D-90471 Nürnberg Tel.: 0911/75884-0 01/2013 Fax: 0911/75884-100 Subject to change without notice 43042-941.01(03)

Hardcopies of these operating instructions are available in German and English only. Other languages are recorded on CD-ROM (part of delivery)

Special note: Contents CD-ROM: • File “ReadmeD.txt”

contains detailed informations about this CD-ROM including terms of a license and legal restrictions.

• Program “CD858.exe” for easy and clear CD-Navigation • Technical documentation

- operating instructions FAC 858 (all major languages) - zoom lenses – suitable types and general informations (D + GB only) - examples of use (D + GB only)

• programming software “PGE858” for configuration of camera series FAC 858/FA857 (D+GB only)

Minimum system requirements • PC Pentium 3 • min. 64 MB central memory (≥ 128 MB recommended) • min. 100 MB free harddisk space • SVGA graphics card or higher • CD-ROM disk drive • mouse • 1 free serial interface • monitor or flat screen • Windows NT4+SP4/2000/XP

General Task The FAC 858, FA 857 digital colour camera series are designed for video and security applications. The use of supersensitive and high resolution 1/2 ” CCD sensors allow for very good image quality. Use of high-density ICs offers a lot of features as well as highest possible image quality.

Applications The camera is suitable for indoor and, with suitable weatherproof housing or WP-type, for outdoor use. PC-configuration with program PGE 858 (enclosed) via serial interface RS 485.

If necessary, RS 232/485 interface adapters can be ordered from Funkwerk customer service. Order code:

RS PGE-Win RS485/232 adapter, cable kit I/WP 9.43039-110400

2 FAC 858/FA857 I/WP/IR-S/HS

Camera types FAC858I colour camera, indoor type FAC858I-S colour camera, indoor type with livecheck, ticker and text FAC858I-HS colour camera, indoor type with livecheck, ticker without text FAC858I-IR colour camera, indoor type, with IR sensor FAC858WP colour camera, weatherproof FAC858WP-S colour camera, weatherproof with livecheck, ticker and text FAC858WP-HS colour camera, weatherproof with livecheck, ticker without text FAC858WP-IR colour camera, weatherproof, with IR sensor FA857I monochrome camera, indoor type FA857I-IR monochrome camera, indoor type, with IR sensor FA857WP monochrome camera, weatherproof FA857WP-IR monochrome camera, weatherproof, with IR sensor

Camera types and available accessories: FAC 858I colour camera, indoor 9.43042-1201 FAC 858I-S colour camera, indoor type with livecheck, ticker and

text 9.43042-1202

FAC 858I-HS colour camera, indoor type with livecheck, ticker without text

9.43042-1203

FAC 858I-IR IR colour camera, indoor 9.43042-1204 FA 857I monochrome camera, indoor 9.43042-1101 FA 857I-IR IR monochrome camera, indoor 9.43042-1104 FAC 858WP colour camera, weatherproof 9.43042-1401 FAC 858WP-IR colour camera, weatherproof 9.43042-1404 FA 857WP monochrome camera, weatherproof 9.43042-1301 FAC 858WP-S colour camera, weatherproof with livecheck, ticker and

text 9.43042-1402

FAC 858WP-HS colour camera, weatherproof with livecheck, ticker without text

9.43042-1403

FA 857WP-IR IR monochrome camera, weatherproof 9.43042-1304 CW system camera casing CW 9.43035-1301 CW-N system camera casing CW with power supply 9.43035-1304 W 2 system camera housing W2 9.43038-1501 WN 2 system camera housing W2 with power supply 9.43038-1505 W130 system camera housing W130 9.43037-1245 SD 87 W sun cover for 2/WN 9.43035-1203 SD 87 CW sun cover for CW/CN 9.43035-1303 CW elox. system camera housing CW anodized 9.43035-1309 W 2 elox. system camera housing W2 anodized 9.43038-1509 WN 2 elox. system camera housing W2 with power supply, 9.43038-1510

FAC 858/FA857 I/WP/IR_S/HS 3

anodized SD 87 W elox. sun cover for W2/WN anodized 9.43035-1210 SD 87 CW elox. sun cover for CW/CN anodized 9.43035-1310 WN Kupplung coupling for W2 9.43035-1206 CW Kupplung coupling for CW 9.43035-1305 D-SUB system plug 15pol. 7643070160 SN 830I desktop power supply 7643050170 parallel dongle for Funkwerk security module 943039150100 WIN USB Funkwerk security module 943039160100 PGEWin PGE WIN software license 943039160200 PGE WIN HS PGE WIN HS software license 943039160300 PGE WIN Service

PGE WIN Service software license 943039160400

RS PGE-Win RS485/232 adapter, cable kit I/WP 943039110400 CD PGEWin 3.50.0

configuration tool for PES cameras and accessories 943039110200

FP70 steering plate for system casing W2/WN2 943209131500 FP70 elox. steering plate for system casing W2/WN2 anodized 943209130600 ES76 setting base for system casing W2/WN2 943021160100 ES76 elox setting base for system casing W2/WN2 anodized 943021111000 ES82 setting base for system casing W/WN 943031160400 AGW838 connection for WP cameras 943038190300 AGN838 power supply for AGW838 943038190200 SN810 W power supply, weatherproof 943033160100 AK930 camera terminal box 943036130100 AK187 camera terminal box 943036110100 BMS operating unit 943522170100 Oberteil BMK cover plate for BMK 943522170200 BMS Joystick BMS joystick for SNK 943522170900 BMS-J3 BMS joystick, triaxial 943522171000 Software software for BMS802 943523110700 SNK Globe WD panning head SNK Globe 943037128600 SNK Move panning head SNK Move 943037124500 Sockel 94 socket for SNK Globe/Move 943037140100 SV12NT power supply for SNK Globe/Move 943037180100


Features

Highlighted FAC 858/FA 857 features at a glance: • automatic image setting (SCS/AGC/lens control/LSS/ALL) • integrated image memory for increased photosensitivity, max. 16 additional memory

images, sequential recording with pre triggering, dynamic comparison between memory and live image

• lens connection for all diaphragm types (Vss diaphragm, automatic diaphragm, galvanometric diaphragm and ER diaphragm)

• electronic seat adjustment with 2 memory positions • automatic image setting with adjustable characteristic (peak value, mean value,

adjustment time, back light compensation (BLC) • automatic white balance • automatic black level control • automatic sharpness (aperture) • automatic contrast • external synchronization with Genlock signal, mains interlink or restart • 2 hardware control in-/outputs for different applications • advanced IR sensitivity (only FAC 858-IR, FA 857-IR) • text, time, date insertion • line mirror and image rotation • alarm management • static masking of image areas (max. 8 areas) • pixel error correction (static und dynamic) • remote control interface (RS-485) for configuration and operation • 3 user memories for customized configuration • 1 memory for factory setting • wide reach of supply voltage • galvanic isolation between power supply, video GND and casing • fully compatible with previous Funkwerk systems • Electronic anti-theft protection

The camera may be damaged or destroyed if

• used for purposes other than those specified • wrenched • used outside the ranges specified in the technical data • used in contaminated environments


• directed towards sources of strong light (sun) with open diaphragm (switched on or off) • installed, serviced, configured or repaired by unauthorized and untrained persons The casing warms during operation. Always care for proper installation of zoom lenses or dust protection covers to avoid intrusion of dust that may appear in the image zone.

Camera mounting points pic 2: (1-3) 3 x M 4 threads for AGW adapter housing, wallmounting bracket (4) 1/4” stand thread for general mounting

Pic. 1 Pic. 2

Mounting sequence for rotation of sensor unit pic. 1: The position of the sensor unit in the camera housing can be rotated by 2 x 90° allowing reproduction of normal and 180° turned images.

Attention: First remove all external connectors!

• loosen all screws and insulation rings 4 x (1a/1b) (SW2).

• remove ring nut (3 ).

• unplug 14 pin female multiplug connector from ribbon cable (4).

• rotate sensor holder (5) in the clockwise direction by 90° or 180°.

• plug 14 pin female multiplug connector to strip (orientation lug on top!).

• apply ring nut (3).

• replace 4 screws with insulation rings (1a/1b) and screw tight (SW2).

• Attention These screws fix the base plate of the lens tube at the same time in the case of WP version. Avoid slipping of gasket between base plate and camera housing!

• Prevent sensor surface from dirt and damage!


Connection and installation The I-type connects via 15 pin D-SUB connector (2) plus BNC coaxial video connection (3) for all camera features, zoom lens diaphragm control with 4-pin terminal (4).

The WP-type 12 pin female multipoint connector is used for wiring of electrically controlled zoom lenses.

Connection plug arrangement see page 16.

The WP concept components:


The scope of delivery includes the basic WP camera (1), the tube with mutable length (2) and a sun cover (3).

Connection housing AGW838 (with or without power supply AGN838) and zoom lens are not part of the delivery.

To fix the preassembled tube 4 screws (5) are fixed at the camera housing (SW3). The 3 pin connector connects to the glass heater.

Attention Care for proper positioning of the gasket (7) during tube installation. It may not be squashed in or otherwise damaged.

Sun cover installation at the ribs (14) on both sides of the camera housing requires smooth uncompressing of the inside (13). If the WP-camera is installed in a position realizing angles >30° to the top the sun cover must be fixed by suitable means.

Putting the camera on a connection box uses bottom side fixing points (9), (10).

Attention The gasket (15) between connection box and camera is part of the connection box. It may not be displaced or damaged (squeezed).

Fixing points at the connection box are two ¼“ threads (11), (12) in a distance of 55mm for installation on a panning head, tripod or other fixing means.


Installation of WP tube

The tube length is mutable for use of different lenses. The standard equipment includes 4 extension rings for use of lenses with a maximum length of 74mm and a maximum diameter of 60mm. The “tube extension” accessory kit contains 3 more rings for lenses with a total length of 111mm.

Note: The tube parts are equipped with gaskets (1a), (3a), (5a) and may not be damaged or soiled.

Mounting sequence: Provide tube head with integrated heating and soldered contacts (1), (2), (9).

Attach first ring (3) according to drawing, take care of inside rib pairs (10).

Use M3 screws (4) for fixing ring at head (SW 2,5).

The following rings, if necessary, are screwed the same ways. Take care to install rings 1 & 3 (3) and 2 & 4 (5) in the proper position. Correct positions are achieved with 60° turns. At the last ring before fixing of the tube flange one rib (3b or 5b) must be at the bottom position for connector fixing.

Attach tube flange according to drawing.

Connector fixing is supported by the ribs (5b, 3b, sometimes also 3c) and held down by the flange contour. Screw flange with 3 screws M3, positions according to the number of used rings. In case of 0, 2 or 4 rings use (b1), (b2) and (b3) in case of 1,3 or 5 rings use (a1), (a2) und (a3).

The right picture shows full assembly of the tube with two rings.


Pic. 6 shows maximum lens dimensions. Please take care for lens wiring within the hatched area.

Lenses camera allows following lens control versions:

Diaphragm Focal length Focus

Manual Fixed Fixed Video signal control Manually mutable Manually mutable Snap diaphragm Mutable by motor-driven

control Mutable by motor-driven control

Galvanometer control (DC) Mutable positioning Mutable positioning DC control (ER)


Lens connector The 4 pin lens connector of all indoor types is located at the camera backside.

If WP-type requires diaphragm control only use 4 pin lens socket (8), connectors are often factory-fitted on the lens cables. Open 8 wires remain unused and can be cut off if necessary (9).

4pin PIN

12pin PIN

function

1 1 + U at VS diaphragm (12 VDC) or + U at ER diaphragm (12 VDC) or Damping at galvanometric diaphragm (6 VDC)

3 2 Video signal at VS diaphragm or Remote control at ER diaphragm or Drive + at galvanometric diaphragm or Switching voltage at snap diaphragm

4 3 GND at VS diaphragm or GND at ER diaphragm or GND at galvanometric diaphragm or GND at snap diaphragm

2 4 Damping + at galvanometric diaphragm 5 Zoom large* 6 Zoom small* 7 Focus close * 8 Focus far* 9 POS_COM for lens (positioning)* 10 NEG_COM for lens (positioning)* 11 Zoom reference for positioning)* 12 Focus reference (for positioning)*

* control via external unit (e.g. SNK Globe...)


For vario lenses press enclosed 12-pin connector to ribbon cable and cut off 4 pin lens socket. Install enclosed plug at the lens cable.

The plug consists of two 6-pin pin jacks (2) and (3), 12 crimp contacts and one socket (1). Both pin jacks are plugged to the 12 pin socket with orientation lugs facing outside. The crimp contacts are attached to the lens wires using suitable tools and locked into place in the cavities of the pin jacks as described in the a.m. table with position of pin 1 to be seen from the drawing.

Back focus adjustment This camera generation allows remote controlled back focus adjustment, e.g.

via RS 485 interface with BMK 802 or PGEWin

via enclosed activation magnet pic. 3 (1) at the camera

For camera operation the activation magnet must be positioned directly at one of both lateral check marks at the housing pic. 3 within 5 minutes after switching as 5 minutes after last activation of any button all contacts are locked. This operation method can also be locked according to preset configuration. For proper adjustment diaphragm must be fully opened.


IR cameras

IR-Cameras are equipped with advanced ½“ image sensors for small distances. The diagram shows spectral sensitivity compared with standard cameras. Lenses with stronger virtual diaphragm (spot filter) allow sufficient light damping even when used during full daylight. This spot filter

also works in the infrared area.

Attention! Artificial light (halogen lamps) deteriorates colour fidelity. The high modulation in the IR range may cause signal contraction (colour loss) in the IR range.

Operation with IR lighting requires switching from colour to monochrome operation via RS 485 or control input. It is recommended to choose another operator memory that may also include other modified parameters, e.g. other SCS/AGC windows or other features.

Lenses behave differently with infrared and visible light due to the transmission range allowing uniform focus over the entire spectral range in the case of IR-corrected lenses.

Both back focus settings of uncorrected lenses must be stored at position 1 and 2, automatic back focus must be switched on and both positions must be stored in the operator memory module.

If switching of operator memory is not possible, snap diaphragm lenses should not be used in IR cameras.

Diaphragm adjustment The camera must be configured and adjusted to the relative diaphragm. The configuration software PGE 858 provides necessary tools with suitable instructions (help menu).

Alignment instructions:

diaphragm types actuator default

manual lens adjustment ring sufficient even brightness

VSS automatic

snap automatic alignment test pattern in the monitor until the camera switches

0

10

20

30

40

50

60

70

80

90

100

350

375

400

425

450

475

500

525

550

575

600

625

650

675

700

725

750

775

800

825

850

875

900

925

950

975

1000

1025

1050

1075

1100

1125

1150

1175

1200

nm

%IR-Kameras

Standard-Kameras

B G Rnear-infrared


off independently

DC automatic -

ER automatic -

During automatic diaphragm regulation the shutter time must be always 20 ms.

The configuration- and adjusted values must be stored thereafter.


FAC 858/FA857 I/WP-S/HS The S/HS camera has the following functions in addition to the general functions of the standard camera:

Ticker • Ticker can be switched on/off.

• Ticker position adjustable.

• Simple positioning of the ticker through 3 preset positions: Bottom left, right and center.

The parameters listed above can be stored in the camera as part of the user settings (they are not reset by "factory settings"!).

Live image check a) Live image check can be switched on/off.

b) White lines level 100%.

c) Invisible insertion in 3 lines from line 24 (1st half image) and from line 336 (2nd half image),

Attention: This setting is detected in the monitor; the monitor can switch to "dark" if changes are made!

Restrictions in standard functions a) Backlight menu/backlight option cannot be accessed when live image check active.

b) In the case of "-S/HS" cameras the image memory is blocked, i.e. storage and display of memory images (single images, sequential recording etc.) is not possible.

c) The designations of the cameras are FAC 858 I-S/HS or FAC 858 WP-S/HS with their own identification plate, own item number and own version number.

d) No script insert possible (user text, date &. time, status pages and operating menu) for HS types!

PGEWin-HS Operation and configuration of the function ticker and live image check is only possible in the PGEWin-HS.


Connection plug arrangement system plug WP 48-pin DIN

a b c

1 SX SX GND

2 GND -(F)BAS

3 +(F)BAS GND

4 (F)BAS SABO2_ C

5 Y SABO2 GND_BATT

6 GND U_BATT

7 Zoom_REF* TXD_B

8 Zoom_small* Zoom_large*

9 Focus_REF* SABO1 RXD_B

10 Focus_close* SABO1 Focus_far*

11 TXD_A RXD_A

12 Uobj

13 U_UHR DÄMPF Steuer1

14 -U_HEIZ GND +U_HEIZ

15 BA_IRIS_SB NEG_COM*

16 Steuer2 U_BLENDE POS_COM*

* control via external unit (e.g. SNK Globe...)

top view of contacts


Indoor D-Sub 15-pin

1 RXD _A 9 +U BATT

2 RXD_B 10 ST2

3 ST1 11 SX GND

4 TXD_B 12 TXD_A

5 SX 13 -U BATT

6 -(C) VBS/C 14 GND

7 (C) VBS 15 GND

8 +(CVBS)/Y

Troubleshooting Camera does not work (no output signal)

disconnect camera from mains for a few seconds (Reset)

Camera works, but no image Set or configure diaphragm

Camera works, but image out of focus Adjust back focus

For repair purposes please contact our equipment exchange pool.

address: Funkwerk video systeme GmbH Thomas-Mann-Str. 50 D-90471 Nürnberg Phone: +49 911 75884-232 Fax: +49 911 75884-476

Ansicht auf Kontakte


Technical data FAC 858 FAC 858 IR FA 857 FA 857 IR

LSS 4HI (hlaf

images), ALL

2

LSS 4HI,

ALL 2

LSS 4HI,

ALL 2

LSS 4HI,

ALL 2

Sensitivity 100 % (lx) 0,025 0,45 0,0015 0,02 0,015 0,25 0,001 0,01

Sensitivity 50 % (lx) 0,015 0,2 0,0009 0,01 0,008 0,13 0,0005 0,005

Sensitivity 25 % (lx) 0,007 0,1 0,0005 0,005 0,004 0,07 0,0003 0,003

Sensor 440000 pixel 1/2"

Lens receiver CS....C 13.5 mm… 21.5 mm

Lens immersion depth

CS=5 mm, C=10 mm

Standard 625 lines, 50 Hz acc. CCIR (PAL) 625 lines, 50 Hz acc. CCIR

max. exposure 100 000 lx

Resolution (lines) 480 580

SNR rated

Supply voltage 10…32 VDC

Ambient temperature -25 °C … +55 °C

Storage temperature -40 °C … +70 °C

EMC Within prescriptive limits acc. EN 50081, part1/2, class B

Casings I WP

Power consumption 5.5 W 5.5/12* W

Protection type IP32 IP66

Weight 0.6 kg 2.4 kg

*power consumption with activated heating


FAC 858 I

1/4"

39

163

49,5

17

47,53560

71,5 186,5

FAC 858 WP

40

86,5

92 64,5

56

46

13

35

55

121,

1

124

300

110 42 ...


fac 858 i/wp/ir-s/-hs fa 857 i/wp/ir - funkwerkfac 858 i/wp/ir-s/-hs . fa 857 i/wp/ir . operating...

Documents