f22 filter (stainless steel)d25g25bk48as5o.cloudfront.net/pdf/en_8_550_100_f22.pdf · manual drain...
TRANSCRIPT
F22-400-˙˙DA
0,5
0,4
0,3
0,2
0,1
10 20 30 40 50 60 70 80
2,5 4,0 6,3 8,0 10,0
bar
dm3/s
F22 Filter (Stainless steel)
07/17en 8.550.100.01
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. (2011 - 8171d) © 2015 Norgren Inc.
Technical features
> Port size: 1/2 PTF
> Metallic parts meet NACE*
> Applications include marine environment, oil and gas production, chemical and industrial compressed air systems
* National Association of Corrosion Engineers (NACE) MR-01-75) defines requirements for sulphide stress cracking resistant materials used in well-head and other corrosive environments.
Technical data, standard modelSymbol Port size Filter element Flow *1) Drain Weight Model
(µm) Material (dm3/s) (kg)
1/2 PTF 25 PE 46 Manual 1,88 F22-400-M7DA
1/2 PTF 25 PE 46 Automatic 1,84 F22-400-A7DA
*1) Typical flow with 25μm element at 6.3 bar inlet pressure and 0.35 bar pressure drop.
Option selectorDrain Substitute
Automatic A
Manual M
Filter element Substitute
5 µm, stainless steel 1
25 µm, stainless steel 2
5 µm, polyethylene 6
25 µm, polyethylene 7
Flow rate
Inlet pressure (bar)
Pre
ssur
e d
rop
Flow characteristics
Medium:Compressed airOperating pressure:17 bar max (246 psi)
Filter element:25 or 5 µmPort sizes:1/2 PTF
Ambient/Media temperature:-20 ... +80°C (-4 ... +176 °F)Air supply must be dry enough to avoid ice formation at temperatures below +2°C (+35 °F)
Materials:Body & bowl: stainless steel Filter element: PE or sintered stainless steel Elastomers: Synthetic rubber
31
125
103
52
90
2
8,5
99
1/4 NPT
3476
17
189
242
#
99
3476
1738
,5
18023
3 #
1
F22 Filter (Stainless steel)
Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. (2011 - 8171d) © 2015 Norgren Inc.en 8.550.100.02
07/17
Warning
These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under »Technical features/data«. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems or other applications not within published specifications, consult IMI Precision Engineering, Norgren Inc.
Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products.
EN - Englisch
AccessoriesWall mounting bracket
18-001-962
DimensionsManual drain Automatic drain
Wall mounting bracket
Spares kitFilter element Service kit,
manual drainService kit, automatic drain
Automatic drain
25 µm 4338-99 (polyethylene) F22-100M F22-100A 3000-90
5 µm 4338-01 (polyethylene)
# Minimum clearance required to remove bowl
Dimensions in mm Projection/First angle