exj_8l99 jeep xj service manual
TRANSCRIPT
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 1/16
LAMPS
CONTENTS
page page
BULB APPLICATION . . . . . . . . . . . . . . . . . . . . . 15HEADLAMP ALIGNM ENT . . . . . . . . . . . . . . . . . . 4LAMP BULB SERVICE . . . . . . . . . . . . . . . . . . . . 7
LAMP DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . 1LAMP SERVICE . . . . . . . . . . . . . . . . . . . . . . . . 10LAMP SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . 14
LAMP DIAGNOSIS
INDEX
page page
GENERAL INFORMATIONDAYTIME RUNNING LAMP MODULE . . . . . . . . . 1GENERAL INFORMATION . . . . . . . . . . . . . . . . . 1
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . 1SENTINEL HEADLAMP DELAY MODULE . . . . . . 1
DIAGNOSIS AND TESTINGDIAGNOSTIC PROCEDURES . . . . . . . . . . . . . . 2FOG LAMP DIAGNOSIS . . . . . . . . . . . . . . . . . . . 3
HEADLAMP DELAY MODULE . . . . . . . . . . . . . . 3HEADLAMP DIAGNOSIS . . . . . . . . . . . . . . . . . . 2
GENERAL INFORMATION
GENERAL INFORMATIONEach vehicle is equipped with various lamp assem-
blies. A good ground is necessary for proper l ightingoperation. Grounding is provided by the lamp socket
w h e n i t com es i n con t a c t w i t h t h e m et a l b od y, or
t h r o u g h a s e p a r a t e g r o u n d w i r e .
Wh e n ch a n g i n g l a m p bu lbs ch e ck t h e s ock et f or
corrosion. If corrosion is present, clean i t with a wire
br u s h a n d c o a t t h e i n s i d e o f t h e s o c k e t l i g h t l y w i t h
Mopar Multi-Purpose Grease or equivalent.
SAFETY PRECAUTIONS
WARNING: EYE PROTECTION SHOULD BE USEDWHEN SERVICING GLASS COMPONENTS. PER-
SONAL INJURY CAN RESULT.
CAUTION: Do not touch the glass of halogen bulbs
with fingers or other possibly oily surface, reducedbulb life will result.
Do not use bulbs with higher candle power thanindicated in the Bulb Application table at the end of
this group. Damage to lamp can result.Do not use fuses, circuit breakers or relays hav-
ing greater amperage value than indicated on thefuse panel or in the Owners Manual.
When i t is necessary to remove components to ser-
v ice a n o t he r, i t s h ou ld n ot b e n ece ss a r y t o a p pl y
e xce ss i ve f or ce or ben d a com p on e n t t o r e m ov e i t .
B e f or e d a m a g i n g a t r i m com pon en t , v er i fy h i dd en
fasteners or captured edges are not holding the com-ponent in place.
SENTINEL HEADLAMP DELAY MODULEThe H eadlam p Module delay s t he de-activat ion of
the headlamps for 45 Ϯ 15 seconds after the ignition
switch is turned OFF. The driver engages the module
by t u r n i n g t h e i g n i t i o n s w i t c h O FF, t h e n t u r n i n g t h e
headlamps OFF.
DAYTIME RUNNING LAMP MODULETh e Da y t i m e R u n n i n g L i g h t s (H e a d l a m p s ) Sy s t e m
is instal led on vehicles manufactured for sale in Can-
a d a on l y. Th e h e a d l a m p s a r e i l lu m i n a t e d w h e n t h ei g n i t i o n s w i t c h i s t u r n e d t o t h e O N p o s i t i o n a n d t h e
vehicle is put into motion. The DRL module receives
a vehicle-moving signal from the vehicle speed sen-
sor. This provides a consta nt headlamps-on condi-
t i o n a s l o n g a s t h e v e h i c l e i s m o v i n g . T h e l a m p s a r e
i ll u m in a t e d a t a p p r ox im a t e l y 30 p e r ce n t of n or m a l
intensity.
XJ LAM PS 8L - 1
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 2/16
DIAGNOSIS AND TESTING
DIAGNOSTIC PROCEDURESWh e n a v eh i cl e e xp er i en ce s p r obl em s w i t h t h e
h e a d l a m p s y s t e m , v e r if y t h e con d i t i on of t h e ba t t e r y
c o n n e c t i o n s , c h a r g i n g s y s t e m , h e a d l a m p bu l bs , w i r e
con n ect or s , r el a y, h i gh b ea m d im m er s w i t ch a n dh e a d l a m p s w i t ch . R e fe r t o Gr o u p 8 W, Wi r in g Di a -
gram s for component locat ions and circuit informa -
tion.
HEADLAMP DIAGNOSISAl w a y s b eg in a n y d ia g n os is b y t e st i n g a l l o f t h e
f u se s a n d ci rcu it b r ea k er s i n t h e s y st e m. R ef er t o
G roup 8W, Wiring Dia gram s.
C on v en t i on a l a n d h a l og en h ea d l a m ps a r e i n t er -
ch a n gea b le. I t i s r ecom men d ed t h a t t h ey n ot b e
intermixed on a given vehicle.
HEADLAMP DIAGNOSIS
CONDITION POSSIBLE CAUSES CORRECTION
HEADLAMPS ARE DIM
WITH ENGINE IDLING ORIGNITION TURNED OFF.
1. Loose or corroded battery cables. 1. Clean and secure battery cable clamps
and posts.2. Loose or worn generator drive belt. 2. Adjust or replace generator drive belt.
3. Charging system output too low. 3. Test and repair charging system, refer toGroup 8A
4. Battery has insufficient charge. 4. Test battery state-of-charge, refer to
Group 8A
5. Battery is sulfated or shorted. 5. Load test battery, refer to Group 8A.
6. Poor lighting circuit Z1-ground. 6. Test for voltage drop across Z1-groundlocations, refer to Group 8W.
7. Both headlamp bulbs defective. 7. Replace both headlamp bulbs.
HEADLAMP BULBSBURN OUT
FREQUENTLY.
1. Charging system output too high. 1. Test and repair charging system, refer toGroup 8A
2. Loose or corroded terminals orsplices in circuit.
2. Inspect and repair all connectors andsplices, refer to Group 8W.
HEADLAMPS ARE DIMWITH ENGINE RUNNING
ABOVE IDLE.*
1. Charging system output too low. 1. Test and repair charging system, refer toGroup 8A.
2. Poor headlamp circuit ground. 2. Test voltage drop across Z1-ground,refer to Group 8W.
3. High resistance in headlamp circuit. 3. Test amperage draw of headlamp circuit.
4. Both headlamp bulbs defective. 4. Replace both headlamp bulbs.
HEADLAMPS FLASHRANDOMLY.
1. Poor headlamp circuit ground. 1. Repair circuit ground, refer to Group 8W.
2. High resistance in headlamp circuit. 2. Test amperage draw of headlamp circuit.
3. Faulty headlamp switch circuitbreaker. 3. Replace headlamp switch.
4. Loose or corroded terminals orsplices in circuit.
4. Repair connector terminals or splices,refer to Group 8W.
HEADLAMPS DO NOTILLUMINATE.
1. No voltage to headlamps. 1. Replace fuse, refer to group 8W.
2. No ground at headlamps. 2. Repair circuit ground, refer to Group 8W.
3. Faulty headlamp switch. 3. Replace headlamp switch.
4. Faulty headlamp dimmer switch. 4. Replace headlamp dimmer switch.
5. Broken connector terminal or wire
splice in headlamp circuit.
5. Repair connector terminal or wire
splices.
* Canada vehicles must have lamps ON.
8L - 2 LAM PS XJ
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 3/16
FOG LAMP DIAGNOSIS
HEADLAMP DELAY MODULE
DELAY FUNCTION INOPERATIVE
(1) Ensure headla mps operate before proceeding.
(2) R e m ov e, i n s pe ct a n d t e s t t h e H DL P d e la y 10
amp fuse in junction box. Replace i f defective.(3) Wi t h t h e k ey of f a n d t h e con n ect or d i scon -
n e c t e d , m e a s u r e t h e r e s i s t a n c e f r o m t h e d e l a y m o d -
ule termina l 4 to vehicle body ground. The ohmmeter
should indicat e zero ohms. If not, repair the open cir-
cuit in the wire harness to vehicle body ground.
(4 ) W i t h t h e k e y o n m e a s u r e t h e v o l t a g e be t w e e n
t h e d ela y m od ule t er min a l 8 a n d veh icle b od y
g r ou n d . Th e v ol t m et e r s h ou l d i n d ica t e ba t t e r y v ol t -
a g e . I f n ot , r ep a i r t h e op en ci r cu it i n t h e w i r e h a r -
n e ss f r om i g n it i on s w i t ch t o H DL P d e la y m od u l e.
(5) Turn hea dlamps on and measure volta ge at ter-
m i n a l 6 . T h e v o l t m e t e s h o u l d i n d i c a t e ba t t e r y v o l t -
age. If not repair open circuit between L2 and HDLP
delay module.
(6) Measure the voltage between the delay module
t e r m in a l 2 a n d v eh i cl e bo d y g r ou n d . Th e v ol t m et e rs h ou ld i n di ca t e b a t t e r y v ol t a g e. I f n ot , r ep a i r t h e
op en ci r cu i t i n t h e w i r e h a r n e s s t o t h e H DL P f u se i n
t h e P D C .
(7) I f s t e ps 1 t h r o ug h 6 p r ov e ou t g ood , r e pl a c e
headlamp delay module.
CONDITION POSSIBLE CAUSES CORRECTION
FOG LAMPS ARE DIMWITH ENGINE IDLING ORIGNITION TURNED OFF.
1. Loose or corroded battery cables. 1. Clean and secure battery cable clampsand posts.
2. Loose or worn generator drive belt. 2. Adjust or replace generator drive belt.
3. Charging system output too low. 3. Test and repair charging system, refer toGroup 8A
4. Battery has insufficient charge. 4. Test battery state-of-charge, refer toGroup 8A.
5. Battery is sulfated or shorted. 5. Load test battery, refer to Group 8A
6. Poor lighting circuit Z1-ground. 6. Test for voltage drop across Z1-groundlocations, refer to Group 8W.
7. Both fog lamp bulbs defective. 7. Replace both lamp bulbs.
FOG LAMP BULBS BURNOUT FREQUENTLY.
1. Charging system output too high. 1. Test and repair charging system, refer toGroup 8A.
2. Loose or corroded terminals or
splices in circuit.
2. Inspect and repair all connectors and
splices, refer to Group 8W.
FOG LAMPS ARE DIMWITH ENGINE RUNNINGABOVE IDLE.
1. Charging system output too low. 1. Test and repair charging system, refer toGroup 8A.
2. Poor fog lamp circuit ground. 2. Test voltage drop across Z1-ground,refer to Group 8W.
3. High resistance in fog lamp circuit. 3. Test amperage draw of fog lamp circuit.
4. Both fog lamp bulbs defective. 4. Replace both fog lamp bulbs.
FOG LAMPS FLASHRANDOMLY.
1. Poor fog lamp circuit ground. 1. Repair circuit ground, refer to Group 8W.
2. High resistance in fog lamp circuit. 2. Test amperage draw of fog lamp circuit.
3. Faulty fog lamp switch circuit
breaker.
3. Replace fog lamp switch.
4. Loose or corroded terminals or
splices in circuit.
4. Repair connector terminals or splices,
refer to Group 8W.FOG LAMPS DO NOT
ILLUMINATE.
1. Blown fuse for fog lamps. 1. Replace fuse, refer to group 8W.
2. No ground at fog lamps. 2. Repair circuit ground, refer to Group 8W.
3. Faulty fog lamp switch. 3. Replace fog lamp switch.
4. Broken connector terminal or wire
splice in fog lamp circuit.
4. Repair connector terminal or wire
splices.
XJ LAM PS 8L - 3
DIAGNOSIS AND TESTING (Continued)
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 4/16
HEADLAMP ALIGNMENT
INDEX
page page
GENERAL INFORMATION
HEADLAMP ALIGNMENT . . . . . . . . . . . . . . . . . . 4SERVICE PROCEDURES
FOG LAMP ADJUSTMENT . . . . . . . . . . . . . . . . . 6
HEADLAMP ADJUSTMENT . . . . . . . . . . . . . . . . 5
HEADLAMP ALIGNMENT PREPARATION . . . . . . 4SPECIAL TOOLS
HEADLAMP ALIGNMENT . . . . . . . . . . . . . . . . . . 6
GENERAL INFORMATION
HEADLAMP ALIGNMENTHeadlamps can be al igned using the screen method
provided in th is section. Alignmen t Tool C-4466-A or
e q ui va l en t ca n a l s o b e u s ed . R ef er t o i n st r u ct i on s
p r ov id e d w i t h t h e t o ol f or p r op er p r oce d ur e s. Thepreferred headlamp alignment setting is 0 forthe left/right adjustment and 1” down for theup/down adjustment.
SERVICE PROCEDURES
HEADLAMP ALIGNMENT PREPARATION(1) Verify headlamp dimmer switch and high beam
indicat or operation.
(2) Correct defective components that could hinder
proper headlamp alignment.(3) Verify proper tire inflation.
(4) Clean headlamp lenses.
(5) Verify that luggage area is not heavily loaded.
(6) F u e l t a n k s h ou l d be F U L L . Ad d 2.94 k g (6.5
l bs .) o f w e i g h t o v e r t h e f u e l t a n k f o r e a c h e s t i m a t e d
gallon of missing fuel .
Fig. 1 Headlamp Alignment Screen—Typical
CENTER OF VEHICLETO CENTER OF HEAD-LAMP LENS TOP EDGE OF HIGH INTENSITY ZONEFLOOR TO CENTEROF HEADLAMP LENS 7.62 METERS (25FEET) FRONT OF HEADLAMPVEHICLE CENTERLINELEFT EDGE OF HIGH INTEN-SITY ZONE
8L - 4 LAM PS XJ
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 5/16
ALIGNMENT SCREEN PREPARATION
(1) P osition vehicle on a level surfa ce perpendicu-
l a r t o a f l a t w a l l 7 .6 2 m e t e r s (2 5 f t ) a w a y f r o m f r o n t
of headlamp lens (Fig. 1).
(2) I f n eces sa r y, t a p e a l in e on t h e f loor 7. 62
m e t e r s (2 5 f t ) a w a y f r o m a n d p a r a l l e l t o t h e w a l l .
(3) M e a s u r e f r om t h e f loor u p 1.27 m e t er s (5 f t )a n d t a p e a l i n e o n t h e w a l l a t t h e c e n t e r l i n e o f t h e
v eh i cl e. S i g ht a l on g t h e ce nt e rl in e of t h e v eh i cl e
(f r om r e a r of v eh i cl e f or w a r d ) t o v er i f y a c cu r a c y of
the l ine placement.
(4) Rock vehicle side-to-side three t imes to al low
suspension to sta bil ize.
(5) J ounce front suspension three times by pushing
d o w n w a r d o n f r o n t bu m p e r a n d r e l e a s i n g .
(6 ) M e a s u r e t h e d i s t a n c e f r o m t h e c e n t e r o f h e a d -
lamp lens to t he floor. Tra nsfer measurement to t he
a l ig n men t s cr een (w i t h t a p e). U s e t h is l in e f or
up/down a djustment reference.
(7) M ea s u r e d is t a n ce f r om t h e ce nt e rl in e of t h evehicle to the center of each headlamp being al igned.
Tran sfer measurements t o screen (with ta pe) to each
s i d e o f v eh i cl e ce n t er l in e . U s e t h e s e l i n e s f or l ef t /
right adjustment reference.
HEADLAMP ADJUSTMENTA pr op er l y a i m e d l ow bea m w i l l p r o je ct t h e t o p
edge of high intensity pattern on the screen from 50
m m (2 i n .) a bo ve t o 5 0 m m (2 i n .) bel ow h e a d l a m p
centerline. The side-to-side left edge of high intensity
p a t t e r n s h o u l d be f r o m 5 0 m m (2 i n .) l e f t t o 5 0 m m
(2 in.) right of headla mp centerline). The preferred
headlamp alignment is 0 for the left/rightadjustment and 1” down for the up/downadjustment. The high beams on a vehicle with dual
headlamps cannot be al igned. The high beam pattern
s h ou ld b e c or r ect w h e n t h e l ow b ea m s a r e a l i gn ed
properly.
(1) Remove screws and both headlamp bezels.
(2) C l ea n f r on t of t h e h e a d l a m p s.
(3) Place headlamps on LOW beam.
(4 ) C o v e r f r o n t o f t h e h e a d l a m p t h a t i s n o t be i n g
adjusted.
(5) Tu r n v er t i ca l a d ju st m e n t s cr e w (Fi g . 2) u n t i l
the h eadlamp beam patt ern on screen/wa ll is similart o t h e p a t t e r n d e p i c t e d i n t h e a l i g n m e n t s c r e e n f i g -
ure.
NOTE: When using a headlamp aiming screen:
• Ad ju s t t h e h e a d l a m p s s o t h a t t h e be a m h or i z on -
t a l p o s i t i o n i s a t 0 .
• Ad ju s t t h e bea m v er t i ca l p os i t ion i s 25 m m (1
in) downward from the lamp horizontal centerl ine.(6) R ot a t e t h e h or i z on t a l a d ju st m e n t s cr e w u n t i l
t h e h ea d l a m p b ea m p a t t er n on t h e a i m in g s cr ee n/
w a l l s im il a r t o t h e p a t t e rn i n t h e a l i gn m en t s cr ee n
figure.
(7) C ov er f ron t of t h e h ea d la m p t h a t h a s b een
a d ju st ed a n d a d ju st t h e ot h er h ea d la m p b ea m a s
instructed above.
(8) I n s t a l l h e a d l a m p bez el s . Ti g h t en t h e s cr e w s
securely.
Fig. 2 Headlamp Beam Adjustment Screws
LEFT/RIGHTADJUSTMENTSCREW UP/DOWN ADJUST-MENT SCREWHEADLAMP
XJ LAM PS 8L - 5
SERVICE PROCEDURES (Continued)
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 6/16
FOG LAMP ADJUSTMENT
P r e p a r e a n a l i g n m en t s cr e en . R e fe r t o Al ig n m en tScreen Preparation paragraph in this section. A prop-
e rl y a l i gn ed f og l a m p w i ll p roje ct a p a t t er n on t h e
alignment screen 100 mm (4 in.) below the fog lamp
centerline and straight ahead (Fig. 3).
Rotate the adjustment screw to adjust beam height
(Fig. 4).
SPECIAL TOOLS
HEADLAMP ALIGNMENT
Fig. 3 Fog Lamp Alignment —Typical
VEHICLECENTERLINE CENTER OF VEHICLE TO CENTEROF FOG LAMP LENS HIGH-INTENSITY AREA FLOOR TO CENTEROF FOG LAMP LENS100 mm (4 in.)7.62 METERS (25 FEET)FRONT OF FOG LAMP
Fig. 4 Fog Lamp Adjustment
ADJUSTMENTSCREW MOUNTINGBRACKETFOG LAMP
Headlamp Aiming Kit C-4466–A
8L - 6 LAM PS XJ
SERVICE PROCEDURES (Continued)
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 7/16
LAMP BULB SERVICE
INDEX
page page
REMOVAL AND INSTALLATION
BACK-UP/REAR TURN SIGNAL/TAIL LAMPBULB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CENTER HIGH MOUNTED STOP LAMP(CHMSL) BULB . . . . . . . . . . . . . . . . . . . . . . . . 8
DOME LAMP BULB . . . . . . . . . . . . . . . . . . . . . . 9FOG LAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . 7
FRONT PARK/TURN SIGNAL LAMP BULB . . . . . 7
HEADLAMP BULB . . . . . . . . . . . . . . . . . . . . . . . 7LICENSE PLATE LAMP BULB . . . . . . . . . . . . . . 8MAP READING LAMP BULB . . . . . . . . . . . . . . . 9SIDE MARKER LAMP BULB . . . . . . . . . . . . . . . . 8
UNDERHOOD LAMP BULB . . . . . . . . . . . . . . . . 9VISOR VANITY LAMP BULB . . . . . . . . . . . . . . . . 9
REMOVAL AND INSTALLATION
HEADLAMP BULB
REMOVAL
(1 ) R e m o v e t h e s c r e w s a t t a c h i n g t h e be z e l t o t h e
grille opening panel (Fig. 1).
(2) Remove the screws attaching the retaining ring
t o t h e h e a d l a m p bu ck et .
(3) D i scon n ect t h e h ea d l a m p b ul b w i r e h a r n e ss
connector.
(4) Separate the bulb from the vehicle.
INSTALLATION
(1) Connect wire harness connector.
(2) Position bulb in bucket.
(3) P os i t ion r e t a i n i n g r i n g on h e a d l a m p bu l b a n d
instal l screws.
(4) Instal l headlamp bezel .
FOG LAMP BULB
REMOVAL
(1) Remove the screws attaching the access cover
to the bottom of the fog lamp (Fig. 2).
(2) Remove spring cl ip securing bulb to fog lamp.
(3) Disconnect wire connectors at bulb.
(4) Remove bulb element from fog lamp.
INSTALLATION
CAUTION: Do not touch the bulb glass with fin-
gers or other oily surfaces. Reduced bulb life willresult.
(1) Position bulb element in fog lamp.
(2) Connect wire connectors at bulb.
(3) Instal l spring cl ip securing bulb to fog lamp.
(4) Instal l screws attaching the access cover to the
bottom of the fog lamp.
FRONT PARK/TURN SIGNAL LAMP BULB
REMOVAL
(1) Remove headlamp bezel.
Fig. 1 Headlamp Bezel
HEADLAMP ADJUSTMENTNUT HEADLAMP BEZELPARK/TURN LAMPSPRINGBUMPER
Fig. 2 Fog Lamp Components
FOG LAMPCLIPBULBACCESS COVERBULBSOCKET
XJ LAM PS 8L - 7
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 8/16
(2) R em ov e s cr ew s a t t a ch i ng p a r k/t u r n s ig n a l
lamp to gri l le opening panel .
(3) Rota te bulb socket one-third turn an d remove
it from lamp (Fig. 3).
(4) Remove bulb from socket.
INSTALLATION
(1) Instal l bulb in socket.
(2) Instal l socket in lamp.
(3) I nsta l l park/turn signal lamp.
(4) Instal l headlamp bezel .
SIDE MARKER LAMP BULB
REMOVAL
(1) Remove side marker lamp.(2) Remove bulb and socket from back side of lamp
housing (Fig. 4).
(3) Remove bulb from socket.
INSTALLATION
(1) Instal l bulb in socket.
(2 ) I n s t a l l bu l b a n d s o c k e t i n ba c k o f s i d e m a r k e r
lamp.
(3) I n s t a l l s i de m a r k er l a m p .
BACK-UP/REAR TURN SIGNAL/TAIL LAMP BULB
REMOVAL
(1) Remove tai l lamp.
(2) Rota te bulb socket one-third turn an d remove
bulb socket from lamp (Fig. 5).
(3) Remove bulb from socket.
INSTALLATION
(1) Instal l bulb in socket.
(2) Instal l bulb and socket in lamp.
(3) I n s t a l l l a m p .
LICENSE PLATE LAMP BULB
REMOVAL
(1) Remove screws attaching l icense plate lamp to
li ftgate.
(2) Remove bulb from lamp socket.
INSTALLATION
(1) Instal l a replacement bulb in lamp socket.
(2 ) I n s t a l l s c r e w s a t t a c h i n g l i c e n s e p l a t e l a m p t o
li ftgate.
CENTER HIGH MOUNTED STOP LAMP (CHMSL)BULB
REMOVAL
(1) Remove the screws attaching the lamp housing
t o t h e l i f t g a t e .
(2) Rota te bu lb socket 1/4 tur n a nd pull from hous-
ing (Fig. 6).
(3) Grasp bulb and pull from socket.
Fig. 3 Park/Turn Signal Lamp Bulb
PARK LAMPPARK LAMPBULB
Fig. 4 Side Marker Lamp
SI DE M AR KE RLAMP SIDE MARKER LAMPBULB
Fig. 5 Bulb Socket Removal
TAIL LAMPBULB TAIL LAMP
8L - 8 LAM PS XJ
REMOVAL AND INSTALLATION (Continued)
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 9/16
INSTALLATION
(1) Push bulb into socket.
(2) P osition socket in la mp a nd rotat e 1/4 turn .
(3 ) I n s t a l l t h e s c r e w s a t t a c h i n g t h e l a m p h o u s i n g
t o t h e l i f t g a t e .
UNDERHOOD LAMP BULB
REMOVAL
(1) Disconnect the w ire ha rness connector from t he
underhood lamp.
(2) Rota te the bulb counterclock-wise. Remove i t
from the lamp socket.
INSTALLATION
(1) I n s e r t t h e r e pl a c em e n t bu l b i n t h e l a m p ba s esocket. Rotate it clockwise.
(2) C on n ect t h e w i r e h a r n es s con n ect or t o t h e
lamp.
DOME LAMP BULB
REMOVAL
(1) Remove the dome lamp lens by squeezing i t at
bo t h s i d e s . T h i s w i l l s e p a r a t e t h e l e n s r e t a i n e r t a bs
from the lamp housing shoulders.
(2 ) P u l l t h e l e n s d o w n w a r d t o r e m o v e i t f r o m t h e
lamp housing.
(3 ) Gr a s p bu l b a n d p u l l f r o m l a m p .
INSTALLATION
(1 ) P o s i t i o n bu l b i n l a m p a n d s n a p i n t o p l a c e .
(2) Position the lens at the lamp housing and force
i t u p w a r d i n t o t h e h ou s in g u n t i l t h e r e t a i n e r t a bs a r e
seated on the lamp housing shoulders.
MAP READING LAMP BULB
REMOVAL
(1 ) I n s e r t a f l a t bl a d e s c r e w d r i v e r i n s l o t a t f r o n t
of lens (Fig. 7).
(2) R ot a t e t h e s c r ew d r i v er u n t i l l e n s s n a p s o u t of
the housing.
(3) Remove lens from housing.
(4) Remove bulb from terminals.
INSTALLATION
(1) I n s er t bu lb i n t o r e a d i n g l a m p t e r m in a l s .(2) Replace lens by holding lens level and pushing
r e a r w a r d i n t o h o u s i n g .
(3 ) P u s h l e n s u p t o s n a p i n t o h o u s i n g .
VISOR VANITY LAMP BULB
REMOVAL
(1) Using a small flat blade, carefully pry each cor-
n e r o f l e n s o u t w a r d f r o m l a m p .
(2) Separate lens from lamp.
(3 ) Gr a s p bu l b a n d p u l l o u t w a r d .
INSTALLATION
(1) Position bulb in socket and push into place.
(2) P o s it i on l en s on l a m p a n d s n a p i n t o p la c e.
Fig. 6 CHMSL Bulb
CHMSL CHMSLBULB
Fig. 7 Reading Lamp Bulb
LENS FLAT BLADECONSOLE
XJ LAM PS 8L - 9
REMOVAL AND INSTALLATION (Continued)
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 10/16
LAMP SERVICE
INDEX
page page
REMOVAL AND INSTALLATION
BACK-UP/REAR TURN SIGNAL/TAIL LAMP . . . 11CENTER HIGH MOUNTED STOP LAMP
(CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11DOME LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FOG LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10FRONT PARK/TURN SIGNAL LAMP . . . . . . . . . 10
HEADLAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LICENSE PLATE LAMP . . . . . . . . . . . . . . . . . . 12MAP/READING LAMP . . . . . . . . . . . . . . . . . . . 13SIDE MARKER LAMP . . . . . . . . . . . . . . . . . . . . 11UNDERHOOD LAMP . . . . . . . . . . . . . . . . . . . . 12
VISOR VANITY LAMP . . . . . . . . . . . . . . . . . . . . 13
REMOVAL AND INSTALLATION
HEADLAMP
REMOVAL
(1 ) R e m o v e t h e s c r e w s a t t a c h i n g t h e be z e l t o t h e
gril le opening panel
(2) Remove the screws attaching the retaining ring
t o t h e h e a d l a m p bu ck et .
(3) D i scon n ect t h e h ea d l a m p b ul b w i r e h a r n e ss
connector.
(4) Separate the bulb from the vehicle.
(5) R em ov e t h e s pr i ng a t t a ch i ng t h e h ea d l a m p
bucket to the gri l le opening panel (Fig. 1).
(6) Sl i d e t h e h e a d l a m p bu ck et d ow n w a r d t o d i s en -
g a g e i t f r o m t h e h e a d l a m p a d ju s t i n g s c r e w s .
INSTALLATION
(1) P o si t ion t h e h ea d l a m p b u ck et i n t h e g r il le
opening panel and sl ide the headlamp bucket upward
t o e n g a g e i t w i t h t h e h e a d l a m p a d ju s t i n g s c r e w s .
(2) I n st a l l t h e s pr in g a t t a c hi ng t h e h ea d la m p
bucket to the gri l le opening panel .
(3) Connect the wire harness connector.
(4) Position the bulb in the bucket.
(5) P os i t ion r e t a i n i n g r i n g on t h e h e a d l a m p bu l b
a n d i n s t a l l s c r e w s .
(6) I n s t a l l t h e h e a d l a m p be z el .
FOG LAMP
REMOVAL
(1) D isconnect the fog lamp wire ha rness connec-
tor.
(2) R e m ov e t h e s cr e w s a t t a c h in g t h e f og l a m p t o
the support (Fig. 2).
(3) Separate the fog lamp from the vehicle.
INSTALLATION
(1) P os i t ion t h e f og l a m p i n t h e s u pp or t br a c ke t
a n d i n s t a l l t h e s c r e w s .
(2) Connect the fog lamp wire harness connector.
FRONT PARK/TURN SIGNAL LAMP
REMOVAL
(1) Remove the headlamp bezel .
Fig. 1 Headlamp
HEADLAMP ADJUSTMENTNUT HEADLAMP BEZELPARK/TURN LAMPSPRINGBUMPER
Fig. 2 Fog Lamp
FOG LAMP BUMPER
8 L - 10 LAM PS XJ
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 11/16
(2) Remove the screws at ta ching the park/turn sig-
nal lamp housing to the gri l le opening panel (Fig. 3).
(3) Remove the bulb sockets and separate from the
vehicle.
INSTALLATION
(1) I n s t a l l bu lbs a n d s ock et s i n t h e l a m p h o u si n g .
(2) P osition the park/turn signal lamp housing on
t h e g r i l l e o p e n i n g p a n e l a n d i n s t a l l t h e s c r e w s .
(3) I n s t a l l t h e h e a d l a m p be z el .
SIDE MARKER LAMP
REMOVAL
(1) R em ov e s cr ew s a t t a ch i ng s id e m a r k er l a m p
lens to gri l le opening panel (Fig. 4).(2) R em ov e b u lb a n d s ock et f r om b a ck s id e of
lamp.
INSTALLATION
(1 ) I n s t a l l bu l b a n d s o c k e t i n ba c k o f s i d e m a r k e r
lamp.
(2) I ns t a ll s id e m a r ker l a mp i n g ri ll e op en in g
panel.
BACK-UP/REAR TURN SIGNAL/TAIL LAMP
REMOVAL
(1) Open the l i ftgate.
(2) R e mov e t h e bol t s a t t a ch i n g t h e t a i l l a m p h ou s -
i n g t o t h e q u a r t e r p a n e l (Fi g . 5 ) .
( 3 ) G r a s p t h e l a m p a n d p u l l t o d i s e n g a g e i t f r o m
t h e g r o m m e t a t t h e ba s e o f t h e l a m p .
(4) R ot a t e t h e b u lb s ock et s on e-t h i r d t u r n a n d
remove the bulb sockets from the lamp housing.
INSTALLATION
(1 ) I n s t a l l t h e bu l b a n d s o c k e t s i n t h e l a m p h o u s -ing.
(2) P o s it i on t h e l a m p h ou s in g i n t h e q u a r t e r p a n e l
a n d p u s h t o e n g a g e t h e g r o m m e t .
(3) I n s t a l l t h e l a m p h ou s in g s cr e w s . Ti g h t en t h e
screws securely.
(4) I n s t a l l t h e b ol t s a t t a ch i ng t h e t a i l l a m p h o us -
i n g t o t h e q u a r t e r p a n e l .
(5) Close the l i ftgate.
CENTER HIGH MOUNTED STOP LAMP (CHMSL)
REMOVAL
(1) R e mov e t h e s cr ew s a t t a ch i ng t h e C H M S L t othe l i ftgate (Fig. 6).
(2) Disconnect the wire harness connector.
(3) Se pa r a t e t h e C H M SL f r om t h e v e h i cl e.
INSTALLATION
(1) Connect the wire harness connector.
(2 ) P o s i t i o n t h e C H M SL o n t h e l i f t g a t e .
(3 ) I n s t a l l t h e s c r e w s a t t a c h i n g t h e C H M SL t o t h e
li ftgate.
Fig. 3 Park/Turn Signal Lamp
NUTBEZELPARK/TURN LAMPBUMPER
Fig. 4 Side Marker Lamp
GRILLE OPEN-ING PANEL FENDERSIDE MARKERLAMP
Fig. 5 Tail Lamp
TAIL LAMPREAR BUMPERGROMMET
XJ LAM PS 8 L - 1 1
REMOVAL AND INSTALLATION (Continued)
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 12/16
LICENSE PLATE LAMP
REMOVAL
(1) R em ov e s cr ew s a t t a ch i ng t h e l ice ns e p la t e
l a m p t o t h e l i f t g a t e .
(2) Remove the bulb from the lamp socket.
INSTALLATION
(1) Instal l bulb in the lamp socket.
(2 ) P o s i t i o n t h e l i c e n s e p l a t e l a m p o n t h e l i f t g a t e
a n d i n s t a l l s c r e w s .
UNDERHOOD LAMPThe underhood lamp is instal led on the hood inner
pa n el. Th e la m p i llu min a t es w h en t h e h ood is
op en e d . Th e l i q u id O N/O FF s w i t ch t h a t i s i n t eg r a l
w i t h t h e l a mp b a se con t r ol s t h e oper a t ion . Th e
s w i t ch p r ov id e s a u t o m a t i c O N/O FF f u n ct i on s e a ch
time the hood is opened and closed.
REMOVAL
(1) Disconnect the w ire ha rness connector from t he
lamp.
(2) Rota te the bulb counterclock-wise. Remove i t
from the lamp base socket.
(3) R em ov e t h e s cr ew t h a t a t t a ch es t h e l a mp
reflector and support bracket (Fig. 7).
(4) Remove the lamp from the hood inner panel .
INSTALLATION
(1) Position the underhood lamp on the hood inner
panel.
(2) I n s t a l l t h e s cr ew t h r ou g h t h e l a m p a n d i n t o
th e hood panel. Tight en t he screw securely.
(3) I n se rt a r ep la c em en t b ul b i n t h e l a m p b a s e
socket. Rotate it clockwise.
(4) C on n ect t h e w i r e h a r n es s con n ect or t o t h e
lamp.
DOM E LAMP
REMOVAL
(1) Remove the dome lamp lens by squeezing i t at
bo t h s i d e s . T h i s w i l l s e p a r a t e t h e l e n s r e t a i n e r t a bs
from the lamp housing shoulders.
(2 ) P u l l t h e l e n s d o w n w a r d t o r e m o v e i t f r o m t h e
lamp housing.
(3) R e mov e t h e f a s t e n e r s a t t a c h in g t h e l a m p t o t h e
roof (Fig. 8).
(4) Disconnect the wire harness connector.
(5) R e mov e t h e l a m p h ou s i ng f r om t h e h e a d l in e r
cavity.
INSTALLATION
(1) P o si t ion t h e d om e l a m p h ou s in g a t t h e h ea d -
liner cavity.
(2) Connect the wire harness connector.
(3 ) I n s t a l l t h e f a s t e n e r s a t t a c h i n g t h e l a m p t o t h e
roof.
Fig. 6 Center High Mounted Stop lamp
U-NUTLIFTGATECHMSL
Fig. 7 Underhood Lamp
WIRE CONNEC-TOR UNDERHOOD LAMPAND SWITCHSCRE WHOOD INNER PANELCONVOLUTED WIRE HAR-NESS COVERGROMMETWIRE HOLE
Fig. 8 Dome Lamp
HEADLINERDOME LAMP BULBLENSNUT FWD
8 L - 12 LAM PS XJ
REMOVAL AND INSTALLATION (Continued)
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 13/16
(4) Position the lens at the lamp housing and force
i t u p w a r d i n t o t h e h ou s in g u n t i l t h e r e t a i n e r t a bs a r e
seated on the lamp housing shoulders.
M AP/READING LAM PThe ma p/rea ding lam p can be serviced by removing
t h e o v e r h e a d c o n s o l e . R e f e r t o Gr o u p 8 C , O v e r h e a dConsole for removal/insta llat ion procedures.
VISOR VANITY LAMP
REMOVAL
(1) Fold down sunvisor.
(2) S t a r t i n g a t t h e b a s e of t h e l a m p a s s em b ly a n d
working right-to-left , use a small flat blade, carefully
pry lamp from visor.
(3) D i scon n ect v is or l a m p w i r e con n ect or a n d
remove from vehicle.
INSTALLATION
(1) P osition visor lamp at visor an d connect visor
lamp wire connector.
(2) P os it i on v is or l a m p i n v is or a n d p re ss i n t o
place.
XJ LAM PS 8 L - 1 3
REMOVAL AND INSTALLATION (Continued)
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 14/16
LAMP SYSTEMS
INDEX
page page
REMOVAL AND INSTALLATION
DAYTIME RUNNING LAMP MODULE . . . . . . . . 14
SENTINEL HEADLAMP DELAY MODULE . . . . . 14
REMOVAL AND INSTALLATION
SENTINEL HEADLAMP DELAY MODULE
REMOVAL
(1) Remove the knee blocker.
(2 ) R e m o v e t h e s c r e w t h a t a t t a c h e s t h e m o d u l e t o
the inside of the instrument panel (Fig. 1).
(3) D is con n ect t h e w i r e h a r n es s con n ect or a n d
remove the module from the instrument panel .
INSTALLATION
(1) P osition the module inside the I/P an d connect
the wire harness connector to the module.
(2) I n s t a l l t h e s c rew t h a t a t t a ch es t h e m o du l e t o
t h e i n s id e o f t h e i n s t r u me n t p a n e l.
(3) Instal l the knee blocker.
DAYTIME RUNNING LAMP MODULE
REMOVAL
Th e D a y t i m e R u n ni n g L i gh t s (D R L ) m od u le i s
l oca t e d o n t h e r i g h t f e n d er i n n er p a n e l a d ja c en t t o
the dash panel (Fig. 2).
(1) Disconnect the wire harness connector from the
module.
(2) R e m ov e t h e s cr e w s t h a t a t t a c h t h e m o d u le t o
the fender inner panel .
(3) Re mov e t h e m od u le f r om t h e f en d er i n ne rpanel.
INSTALLATION
(1) P o s it i on t h e m od u l e o n t h e r i g h t f en d er i n n er
panel.
(2) I n st a l l t h e a t t a ch in g s cr ew s . Ti gh t en t h e
screws securely.
(3) Connect the w ire ha rness connector to t he mod-
ule.
Fig. 1 Headlamp Delay Module
HEADLAMP DELAY MOD-ULE BRACKET
Fig. 2 Daytime Running Lamp Module
DAYTIME RUNNING LIGHTMODULE
8 L - 14 LAM PS XJ
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 15/16
BULB APPLICATION
INDEX
page page
GENERAL INFORMATION
GENERAL INFORMATION . . . . . . . . . . . . . . . . 15SPECIFICATIONS
EXTERIOR LAMPS . . . . . . . . . . . . . . . . . . . . . 15
INTERIOR LAMPS . . . . . . . . . . . . . . . . . . . . . . 15
GENERAL INFORMATION
GENERAL INFORMATIONTh e f ol low i n g B u l b Ap pl ica t i o n Ta bl es l i st s t h e
l a m p t i t l e o n t h e l e f t s i d e o f t h e c o l u m n a n d t r a d e
n u m be r o r p a r t n u m be r o n t h e r i g h t .
CAUTION: Do not use bulbs that have a highercandle power than the bulb listed in the Bulb Appli-cation Table. Damage to lamp can result. Do not
touch halogen bulbs with fingers or other oily sur-faces. Bulb life will be reduced.
SPECIFICATIONS
EXTERIOR LAMPS
LAMP BULB
B a ck -u p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 157
Center High Mounted Stoplamp . . . . . . . . . . . . . 921
F og l a m p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H 3
Fr o n t Si d e M a r k er . . . . . . . . . . . . . . . . . . . . . . . 1 68
Headla mp/Sealed B eam . . . . . . . . . . . . . . . . . H6054
L i ce n se P l a t e . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 68
P ar k/Turn S ignal . . . . . . . . . . . . . . . . . . . . . . . 3157
Tail/St op . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3157
R e a r Tu r n Si g n a l . . . . . . . . . . . . . . . . . . . . . . . 3 157
INTERIOR LAM PSSe r v ice p r oce d ur e s f o r m o s t of t h e l a m p s i n t h e
i n s t r u m en t p a n e l, I n s t r u m en t cl u st e r a n d s w i t ch e s
a r e loca t ed in G r ou p 8E , I n st r um en t P a n el a n d
Ga u g e s . So m e c o m p o n e n t s h a v e l a m p s t h a t c a n o n l y
be serviced by an Authorized Service C enter (ASC)
a f t e r t h e com p on e n t i s r e m ov ed f r om t h e v eh i cl e.
Contact local dealer for location of nearest ASC.
LAMP BULB
C a r g o . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 61
Do m e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 61
LAMP BULB
Do m e/R e a d i n g . . . . . . . . . . . . . . . . . . . . . . . . . . 906
Gl o ve C o m pa r t m e n t . . . . . . . . . . . . . . . . . . . . . . 194
Overhead Console . . . . . . . . . . . . . . . . . . . . . . . . 912
U n d e r H o od . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 05
Va n i t y M i r ror . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
U n d e r pa n e l C o u r t es y . . . . . . . . . . . . . . . . . . . . . 168INDICATOR LAMPS
Se r v ice p r oce d ur e s f o r m o s t of t h e l a m p s i n t h e
i n s t r u m en t p a n e l, i n s t r u me n t cl u st e r a n d s w i t ch e s
a r e loca t ed in G r ou p 8E , I n st r um en t P a n el a n d
Ga u g e s .
LAMP BULB
A/C C on t r o l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
Ai rb a g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
An t i -l ock B r a k e . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
B r a k e Wa r n i n g . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
C h e ck E n g i n e . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4C h eck G a u g es . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
C i g a r L i g h t e r . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3
C ool a n t Te m p H i gh . . . . . . . . . . . . . . . . . . . . . . 1 94
C r u is e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
F a s t e n S ea t B e l t s . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
Fou r Wh e el Dr i v e . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
Ge n e r a t o r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 94
H e a t e r C o n t r ol . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
H i g h B e a m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
I l l um i n a t i on . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 03
L ow F u el . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
L ow O il P r e ss u r e . . . . . . . . . . . . . . . . . . . . . . . . 1 94
L ow Wa s h e r Fl u i d . . . . . . . . . . . . . . . . . . . . . . . . 7 4
R a d i o . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASC
Se cu r i t y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
Tr a n s f e r C a s e . . . . . . . . . . . . . . . . . . . . . . . . . . . 658
Tra nsmission Floor Shift . . . . . . . . . . . . . . . . . . 658
Tu r n Si g n a l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
U p s h i ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4
XJ LAM PS 8 L - 1 5
7/29/2019 EXJ_8L99 jeep xj service manual
http://slidepdf.com/reader/full/exj8l99-jeep-xj-service-manual 16/16