eurostyle 6’x8’eurostyle 6’x8’ greenhouse 255x193x203 cm / 100”x76”x80” keep these...
TRANSCRIPT
-
Cat
alog
No.
661
63 *
Ver
sion
#3
EuroStyle 6’X8’Greenhouse
255x193x203 cm / 100”X76”X80”
Keep these instructions in a safe place for future reference.
You must read these instructions carefully before you start to assemblethis greenhouse. Please carry out the steps in the order set out in theseinstructions.
Do not tighten the screws of the Greenhouse until completing on theassembly of the panels.
We strongly recommend the use of work gloves during assembly . Do not attempt toassemble the greenhouse in windy or wet conditions.Do not touch overhead power cables with the aluminum pro�les. Always wear shoesand safety goggles when working with extruded aluminum. Dispose of all plastic bagssafely - keep them out of reach of small children. The greenhouse must be positionedand �xed on a �at level surface. Do not lean against or push the greenhouse duringconstruction. Keep children away from the assembly area. Do not position your greenhousein an area exposed to excessive wind.Do not attempt to assemble this greenhouse if you are tired, have taken drugs or alcoholor if you are prone to dizzy spells. If using a step ladder or power tools ensure that youfollow the manufacturers safety advice. Hot items such as recently used grills, blowtorchesetc. must not be stored in the greenhouse. Ensure there are no hidden pipes or cablesin the ground before inserting the pegs.
SAFETY ADVICE
GENERAL ADVICEInventory all parts before beginning the assembly process to ensure that there are nomissing parts. This is a multi-part assembly that typically requires at least 3 hours. To beconservative, please allow at least 6 hours for assembly process to ensure time forcompletion..Selecting a site - choose a sunny level position away from overhanging trees. If you are�xing your greenhouse directly to a solid concrete foundation use the pre drilled holesin the metal base supplied. The component parts should be checked and laid out closeat hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.Keep roof clear of snow and leaves.
When your greenhouse needs to be cleaned, use a mild detergent solution and rinsewith cold clean water. DO NOT use acetone, abrasive cleaners or other special detergentsto clean the clear panels.Replacement parts - contact Customers service helpline at: 877-627.8476.For additional information please visit our web site: www.palramapplications.com
CARE & MAINTENACE
TOOLS & EQUIPMENT- Silicone sealant applicable to panels & Applicator- Tape measure- Work gloves- Plastic or rubber mallet- Lubricant- Phillipshead-- Step ladder- Drill- Large hammer- Scissors- 2mm (5/64) metal drill bitIf help is required seek professional advice whithin store.
IMPORTANT
ASSEMBLY INSTRUCTIONS
-
IMPORTANT
- A - Aluminum profiles and parts.
- P5XX – Polycarbonate panels.
- P3XX – Plastic parts.
- M – Metal parts.
- 4XX – Screws, nuts, disks, etc.
Please carefully read all notes, instructions & remarks, BEFORE STARTING THE ASSEMBLY of the greenhouse.
Sort the parts and check against the contents parts list.
Carry out the assembly steps in the order set out in the instructions.
Screws 411 are to be assembled from the outside and nuts 412 from the inside of the greenhouse.
Close screws and nuts (411 & 412), 2-3 turns only, do not fasten them until completion of the assembly,
if not specified otherwise.
Prefix of the parts reference in the assembly instructions:
The end of all profiles, pointed by an arrow, is always upward.
The oval hole in the crossbars A256 should always be assemble to the base of the greenhouse.
The front of the greenhouse is the wall including the door, and the back is the opposite wall.
Firmly connect the greenhouse to a leveled final position immediately after completion of the assembly.
-
ContentsItem Qty.Inc./mm
A102 44.33”/1126mm 12A103 62.40”/1585mm 1A104 62.40”/1585mm 1
A111 44.69”/1135mm 2A112 44.69”/1135mm 2A113 44.96”/1142mm 1A114 44.96”/1142mm 1A115 44.96”/1142mm 1A116 44.96”/1142mm 1
A131 96.73”/2457mm 2
A141 97”/2463mm 1
A151 23.07”/586mm 1
A171 59.65”/1515mm 2
A172 24.17”/614mm 1
A181 24.17”/614mm 1
A201 61.48”/1560mm 1A202 61.48”/1560mm 1
A211 24.25”/616mm 1
A221 48.82”/1240mm 1
A231 23.82”/604mm 1
A251 24.84”/630mm 1
A253 72.76”/1848mm 1A254 24.02”/610mm 2
A256 50.79”/1290mm 8
A261 15.75”/400mm 1
A271 23.07”/586mm 1
A282 21.77”/553mm 2
A191 24.17”/614mm 1
M243 2
.
Item Qty.Inc./mm Item Qty.Inc./mm
A161 49.07”/1246mm 1
-
Contents
(2 spare)
K i t A c c e s s o r i e s
Item Qty.Inc./mm
M244 2
P517 10.63” x24.09” 1
P513 22.64” x24.09” 1
1135X612 mm
270X612 mm
575X612 mm
P516 25.79” x24.09” 1666X612 mm
P514 17.32” x24.09” 2440X612 mm
P515 17.32” x24.09” 2440X612 mm
P505 9.45”x23.94” 1240X608 mm
P512 23.62” x21.65” 1600X550 mm
Item Qty.Inc./mm Item Qty.Inc./mm
P311 44.09”/1120mm 42P312 61.42”/1560mm 6P313 9.84”/250mm 2P314 28.74”/730mm 2P315 14.17”/360mm 2
R303 59.6”/1515mm 2
4P324
P302
A306
A323
M307
P301
2
1
2
4
2
431 1/8”X1/2”/1/8’X13 9(1 Spare)
(1 Spare)P316 3.94”/100mm 9
447 M8X0.63”/M8X16 4
411 M6X0.39”/M6X10 85
412 M6 90
421 M4X0.63”/M4X16 6
422 M4 4
445 8X1/2”/M8X7 4
441 M6X1.77”/M6X45 1
442 0.26”/6.5mm 1
443 0.26”/6.5mm 4
P502 44.69”x24.09” 21
P317(1 Spare) 14
1P333
-
Be sure to bend in the tabs of the base profiles M243 into a 90° anglebefore inserting the screws.Tighten firmly the screws 447 at the lower hole as seen in the lowerpicture.
Attach the sides of the base (M244) to the front and back base pieces(M243).Use the aluminum screws and nuts (411, 412) as shown. Tighten nutcompletely.
1 2
M243
M243
M244
447
M243
Front Side
M243
Connectors
M244
M244
M243
A244
412
411
Back Side
M244
-
Pay attention to set the aluminum corners (A111, A112) according tothe marks showing bottom and top.
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.
NOTE: The assembly of profile A161 should be done simulataneouslywith profile A111.The other side of profile A161 will be connected later.
NOTE: The nuts are to be from the inside. Do not tighten them untilcompletion of the assembly, If not specifically stated otherwise, thisprocedure applies to all cases wherescrews and nuts 411, 412 are to be used.
A111A111
A161
412
411 411
412
411
412
411
from the inside
QTY
2#A111#A112
1#A161
QTY
A161
3
-
4 Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.
BACK
(a)
A112
A111
A112
A111411
A111 411
412
QTY
2#A111#A112
A111
2FROM THE INSIDE
-
NOTE: Screws 411 should be inserted through the lower oftwo holes in profile A253.
NOTE: Profiles A256 are assembled from the inside.The upper holes will be used later on.
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.5
BACK
!!
A256 A256
411
412
A256
412
411
BACK
A256 A256
411
412 411
A253
412
2#A256
QTY
1#A253
QTY
412
411
A256
-
NOTE: The set includes two left and two right “gutter end cups” P324and four plugs. Assemble a plug in all four “gutter end cups” P324. Insert eachone of them into the gutters A131 ends.
NOTE: Leave the end cup open on the side you would like the water to drain. (a)
A131
(b)
(b)
P324
P324
P324
4#A324
QTY
6
2#A131
QTY
-
Assemble the gutter A131 to the profiles (A111/A112) oneon each end.NOTE: Assemble the crossbars A256 from the insidesimultaneously with the gutter A131 using the same screwsand nuts. The oval holes in A256 must be connected tothe base of the greenhouse.
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.7
2#A131
QTY QTY
4#A256
A256
A256
!
BACK
A256
A256
411
412
411
412
411
411
412
A131
A131
A256A256
A256
A256
411
-
a
A253 BACK
A104
A103
411
A103
A104
!BACK
412
411
A104
b
b
!!
a
a
411
A103A253
The slanted end of the profiles A103 and A104 shouldbe parallel to the downward slope of the roof. Theother end should be insert onto the head of screws411 connecting the crossbars to the base. Insert onescrew 411 in each profile A103, A104 and connect toprofile A253(b).
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.8
QTY
1#A1031#A104
-
Profiles A254 should be connected throughthe lower of the two holes to profiles A111and A112. At their other end, they should beconnected to profiles A201 and A202.
NOTE : Assemble the crossbars A256Simultaneously with the profiles A254 andprofiles A111 and A112, using the same screwsand nuts. The oval holes must be connectedto the base of the greenhouse.
BACK
A202
A256
A256
!
A254
OUTSIDE411
412
A256INSIDE
412
411
A256
INSIDE
OUTSIDE
OUTSIDE
INSIDE
FRONT
411
411
412411
411
412
A201
A254
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.9
QTY
2#A254#A256 2
QTY
1#A201
1#A202
A254
-
Aluminum profiles A113, A114 are to be connected at the front to aluminum profiles A254 using the upper of the two holes. Aluminum profilesA115, A116 are to be connected at the back to aluminum profile A253 - on its two sides using the upper holes. Profiles A113, A114, A115, A116are to be also connected Simulaneously to profiles A131.
A116
411
412
411411
411
411
412
412
412
A113
A253
411
FRONT
BACKA131
A131
A114
A115
FRONT BACK
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.10
QTY1#A113111
#A114#A115#A116
-
Assemble the main beam A141 UNDER A113, A114at the FRONT, A115 and A116 at the BACK .
A141
411
412
411
412
A211
411
412412
411
QTY
1#A141
QTY
1#A211
11 Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.
Assemble profile A211, from the outside, to profiles A113,A114.
-
Slide profile A102 on to the preassembled (to the base) screw 411.On the other end slide the head of screw 411 into the groove onprofiles A102, insert the screw into predrilled holes in the gutter A131and close (DO NOT TIGHTEN) with nut 412.
NOTE: Repeat the above assembly procedure to all six profiles A102.You will have to add one screw 411 and nut 412 to each side of thebase in order to assemble the middle profile A102. (* See next step)
A102
A102
412
412
©b®
102
412
411
(c)
A102
412
411
(a)
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.12
QTY
6#A102
-
Slide profile A102 on to the preassembled (to the base) screw 411. Onthe other end slide the head of screw 411 into the groove on profilesA102, insert the screw into predrilled holes in the gutter A131 and close(DO NOT TIGHTEN) with nut 412.
412
411
A102
A102
(a) (b)
412
411
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.13
QTY
6#A102
A102
-
NOTE: The vent in the roof can be inserted replacing one of themiddle sections panels.
In order to assemble the vent you have to insert an additional screw411(b) into two profile A102(b) on both sides of the vent before youconnect it. These two additional screws will be used in the next step.
411
412
(a)
(a)
(b) 411
A102
(a)411
412
411
(a)
(b)
411
412
412
412 412
A102
412
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.14
QTY
6#A102
-
Assemble aluminum profile A251 using the additional screws youinserted on the previous step.
412
A251A251
A251
412
A261
A221(a)
(b)
A211
412
411
442
412
441
(b
A261412
441A261
442
441
(c)
Assemble aluminum profile A221 onto aluminum profile A211(a) .Connect aluminum profile A221(b) and aluminum profile A261 toprofile A113(c).
QTY
1#A251
QTY
1#A221
QTY
1#A261
Insert the screws from the outside, tighten nuts only 2-3 turns and leave loose.15 16
A221
A113
-
P301
A191
A191
P301
P301
A191
P301
Lay profiles A171 L&R on a flat surface. Lay between them profiles A172,A181 and A191 including preassembled P301 as shown below and tightenall screws.
Door Assembly- When inserting the plastic part No. P301 to aluminumProfile A191 use plastic or rubber mallet. After you inserted part A301push it in approximately 2”/50mm from the profiles A191 end.
17 18
QTY
1#A191
QTY
2#A301
431
421
A172
A172
431
A191
(c)
A181
431
431
431
A171 L & R
QTY
2#A171
1#A172
QTY
1#A181
1#A191
A191
-
When inserting the panel to the door use a flat surface and if the panel doesnot fit properly, trim the lower and upper corners of the panel.
NOTE: Make sure the grooves on both sides of the panel are properlypositioned along the aluminum-extruded profiles.
C
D
B
D
C
B
A
A
19 20
QTY
1#P502
During the assembly of plastic strips you must put pressure on them untilthey snap into place. Put the pressure at one end of the platic strip andcontinue all the way to the other end.
QTY
1#P517
P502
P502 P517
QTY
2#P311
-
QTY
2#P313
21
A231
411
412A181
412
411
412
A231
A181
Lay profile A231 on profile A181 and connect them with screws andnuts 411,412.
22
A231
-
443
421
P302
422
443
422
A231
P302
422
A181
P302443
A231
421
443
QTY
421
#P302
2
2
QTY
443
422
4
2
23
Assemble of the wheels to profile A231.
Note: Make sure to assemble all parts in theorder described in i l lustration below.Part No’ 443 must be assembled, one underscrew 421 head and one between the wheeland profile A231.
-
VENT SUBASSEMBLYAssemble the handle A306 to profile A271 and tighten screws 421(a) andnuts 422(a). Slide panel P512 into the groove in profile A151(b). Slide profilesA282 on each side of panel P512 until they fit the holes on profile A151ends and the two holes on panel P512(c).
422
A306
421
A271
(a)
When inserting the rubber R303 apply some lubrication solution on thealuminum A171.
R303
24 25
QTY
2#R303
QTY
1#A151
Connect corners with screws 411 and nuts 412.Slide the final profile A271 (with the handle) until it fits the holes on bothprofiles A282 and the two holes on the panel P512(d). Connect cornerswith screws 411 and nuts 412 . Tighten all screws and nuts.
QTY
1#A271
412
412
A282
A282
A151
A271
(b)
411
411
411
411
(c)
(c)
(d)
(b)
P512
1#A282 1#A306
-
(b)
A251
A141
A306
(b)
(a)
INSIDE
A251
445
A251A323
The brackets A323 should be connected to profile A251 using screws 445(a). To install the vent on main bean aluminum profiles A141, hold it at an angleof 45° relative to the profile’s plane Slide it to the position between the tworoof aluminum profiles AI02(b). The handle A306 should rest on brackets(A323) when the vent is in the closed position.In the open position, the vent can be secured in one of several angles, bycatching a selected hole in the handle with the protruding tip of bracketsA323.
26 27
QTY
2#A323
QTY
4445
-
QTY
14#P317
28
P317
P317
P317
Noise reduction elements assembly. Put one part of P317 in the middle of eachsection of the wall as shown in the picture below it will be used later on.
-
(b3)(b1)
(b2)
Note: Make sure the panel is secure in P317 plastic holder (a). Makesure the grooves on both sides of the panel are properly positionedalong the aluminum – extruded profiles.* See also next step.
During the assembly of the plastic strips you must put pressure onthem until they snap into place. Put the pressure at one end andcontinue all the way to the other end-using tool P333, as shown below.
(a) (b)
P502
29
P333
D
A
B
C
D
-
Pay special attention when assembling the triangular polycarbonate sections(P505, P514 and P515). The plastic strips (P311,P312,P314,P315) should beinstalled only after the polycarbonate panels (P505, P514, and P515, P516) arein position.* (see previous step)
P502
P502
P502
P502
P502
P502
P502
P314
P515
P514
P515
P312x2
P502
P516
P315
P505
P514
12
3
5
4
6
7
9
10
11
12
13
14
15
18
17
16
19
8P311
30
QTY
1#P516
QTY
1#P505
QTY
2#P514
#P515 2
QTY
#P502 13
QTY#P311#P312#P314#P315
24622
-
When you mount the polycarbonate panels on the roof,insert the panels by sliding them into the gutter as shownin the picture below.Noise Reduction elements assembly. Insert one partP316 in the middel of each of the roof panels and pushit in the groove of the gutter.
* A step ladder will be needed for this step.
(a)
(b)
P513
P311
P311
P311
(c)P316
(c)(c)
P502
P316
1
23
4
5
6
78
31
QTY
#P316 8
QTY
#P311 14
QTY
#P513 1
QTY
#P502 7
-
307
When fitting the door in its place, pay attention to insert the plastic part(P301) inside the special aluminum rail (A161(a)). It is advised to spreadsome tender lubrication on the rail.After you assemble the door to its place, assemble screw and nut 411,412into the door stopper hole on profile A221(b).
NOTE: Make sure to fasten all screws and nuts.
32 33
(a)
411 (b)
A221
(a)
412
A221
-
FIRMLY CONNECT the greenhouse to leveled final positionIMMEDIATELY after completion of the assembly, towithstand high winds effects.
The pegs M307 (spikes) are assembled from the inside of the greenhouse.Make sure to use the pre-punched notch in the bottom of the base.
M307
34