estimating low temperature pg-grade of binders in rap
TRANSCRIPT
![Page 1: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/1.jpg)
Estimating Low Temperature PG-Grade of Binders in RAP without ExtractionHussain U. Bahia, Tao Ma, Emil Bautista University of WisconsinPeter Sebaaly, Elie HajjUniversity of Nevada-Reno
Spring RAP ETG Meeting April 22, 2009Manchester, NH
![Page 2: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/2.jpg)
Outline
•Relevance •Testing Procedure•Analysis Spreadsheet •Next steps
![Page 3: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/3.jpg)
Research Needs
• Modulus of RAP Mixes• Fatigue Concerns• Final Effective Binder Grade• Performance of High RAP Mixes• Need to Bump Binder Grade• How to Better Control RAP - Fractionating
2007 Survey - Cecil Jones
![Page 4: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/4.jpg)
Concept of Testing • Replace extraction and testing with testing RAP
mortar– Mortar: Voidless mix of selected gradation of RAP with binder
• Estimate PG of binder in RAP from mortar testing • High Temp PG • Intermediate Temp PG • Low Temp PG
– Most critical – Start with BBR
![Page 5: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/5.jpg)
Challenges / Solutions
• BBR is not designed for testing mortars– Not enough load to cause enough deflection – Cannot exceed load –cell limits – Mold is too narrow for casting mortars
• Solutions – Change mold – Done – Increase temp of testing and use models – Done– Re-design BBR allow higher load and measure fracture –
70 % done
![Page 6: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/6.jpg)
Mold Modification1. Wider Sample
12.5 x 10.0 mm 2. Teflon coated3. Stronger end holders
![Page 7: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/7.jpg)
New Terminology
• RAP: Reclaimed asphalt pavement– Selective RAP (SRAP): RAP passing # 8 sieve retained on single sieve or different
sieves combined according to fixed gradation– PAV RAP (PRAP): consists of the aggregates extracted from SRAP mixed with PAV
binder
• Binders (B):– PAV binder (PB): binder subjected to aged process of RTFO+PAV– SRAP binder (SB): aged binder in SRAP;– Blended binder (BB): SRAP binder blended with fresh or PAV binder
•Mortar (M): RAP material mixed with binder– PAV mortar (PM): RAP aggregates mixed with PAV binder by weight percentage;– SRAP mortar (SM): SRAP mixed with PAV binder by weight percentage;
![Page 8: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/8.jpg)
First Approach: Test Mortars, Correlate to Binder
![Page 9: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/9.jpg)
First Approach: Use Blending Chart to Estimate RAP Binder Grade
RAP
Bind
er S
(60)
New
Bind
er S
(60)
![Page 10: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/10.jpg)
Many Problems
•Correlations vary – Highly temperature dependent
•RAP mortars have very high stiffness – hard to control molding
•Blending charts do not work for all loading times
![Page 11: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/11.jpg)
New Approach
• Selective RAP to control molding – # 30, #50, #100
• Use PAV aged binder for blending – Can test at same temp as mortar
• Use more PAV binder to make molding easier • New analysis procedure
– focus on S(60), m(60). • It appears to be working based on verification
![Page 12: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/12.jpg)
Select RAP Gradation
![Page 13: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/13.jpg)
Blending Procedures
• Blending procedure:• Binder and was heated at 150℃ while aggregate and RAP
were heated at 180℃ for 1h before mixing together to get mortar.
• Different mortar samples were heated for different times ( 1 , 2 & 3 hrs) and then left to cool down to the ambient temperature. – During the heating process, mortar was stirred every half an hour and
Argon gas was used to prevent further aging of binder.• All the mortar samples were heated at 150℃ for 1h and then
stirred and poured into beam molds.
![Page 14: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/14.jpg)
Effect of Blending Time – (S-ratio)
T3: With fines
3 hours
2 hours 1 hours
![Page 15: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/15.jpg)
Effect of Blending Time (m-ratio)
![Page 16: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/16.jpg)
Steps – 1,2,3, 4 • Test new binder after PAV at 3 temps
– Two around grade, plus one more temp E.g. for PG xx-22, test at -6 and -12, Plus 0.0C
> At 0.0 C, reduce load in BBR if @ -6 C S(60) <60MPa
• Burn SRAP, estimate %AC, get RAP agg. • Mix SRAP with PAV Binder, total 25% AC
– PRAP, test 2 specimens at 0.0 C • Mix SRAP aggregates with 25% PAV aged AC
– SRAP, test 2 specimens at 0.0 C
![Page 17: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/17.jpg)
1. Estimate Equivalent Limiting Stiffness at Test Temp used for Mortars
PAV Binder (RTFO + PAV)
10
100
1,000
‐14‐12‐10‐8‐6‐4‐20Temperature (�C)
S60 (MPa
S60 (MPa) Equivalent Limited Stiffness
PAV Binder (RTFO + PAV)
0.25
0.30
0.350.40
0.45
0.50
‐14‐12‐10‐8‐6‐4‐20Temperature (�C)
(m‐value)60
m‐value Equivalentm‐value Limit
Mortars Test Temp. = 0.0 C
![Page 18: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/18.jpg)
2. Convert binder to mortar limits( all at 0.0 C)
Stiffness at Testing Temperature
10
100
1,000
10,000
1 10 100 1000Time (sec.)
Stiffness (M
P
PAV Binder Limit Stiffness
m‐value at Testing Temperature
0.10.30.50.70.9
1 10 100 1000Time (sec.)
m‐value
PAV Binder Limit m‐value
Mortar Binder
![Page 19: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/19.jpg)
Allowable RAP Binder
0.29727.72
0.127.72 27.72Allowable %SRAP - m-value
Allowable %SRAPBinder
-16°C1376.947.52
Target binder low temp PG grade:10047.52
27.720.3825-3.09E-03Allowable %SRAP - Stiffness
%SRAPba
m-value = a×(%SRAPBinder)+b1000.2971376.90.31023.64825.5
m-value00.2971376.90.3830.0497.5
47.522.69689.303E-03% SRAPLimit mLimit Sm-value% SRAPS (MPa)
%SRAPBA
log(S) = A×log(%SRAPBinder)+B23.640.310825.50.00.383497.560.00.00
Stiffness% SRAPm-valueS (MPa)% SRAPm-valueS (MPa)
Blended Mortar (Bmortar)PAV mortar (Pmortar)Time (sec.)Temp (°C)
LIMIT PERCENT OF SRAP BINDER
Mortars
Use the PAV Mortar limit stiffness and m-value at test temp from step 3 to determine the limit % of SRAP binder.
Step 4 - SRAP Binder Limit Percentage
![Page 20: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/20.jpg)
Allowable RAP Binnder
0.387-1.60
0.1-1.60-1.60
Allowable %SRAP - m-value
Allowable %SRAP Binder
-22°C704.316.22
Target binder low temp PG grade:10016.22
-1.600.3825-3.09E-03Allowable %SRAP - Stiffness
%SRAPba
m-value = a×(%SRAPBinder)+b1000.387704.30.31023.64825.5
m-value00.387704.30.3830.0497.5
16.222.69689.303E-03% SRAPLimit mLimit Sm-value% SRAPS (MPa)
%SRAPBA
log(S) = A×log(%SRAPBinder)+B23.640.310825.50.00.383497.560.00.00
Stiffness% SRAPm-valueS (MPa)% SRAPm-valueS (MPa)
Blended Mortar (Bmortar)PAV mortar (Pmortar)Time (sec.)Temp (°C)
LIMIT PERCENT OF SRAP BINDER
Mortars
Step 4 ‐ SRAP Binder Limit Percentage
100
1,000
‐10 10 30 50 70 90Percentage of SRAP Binder (%)
Smortar at 60 sec. (MP
0.1
1.0
(m‐value) mortar at 60 sec
Mortar Stiffness Limit Stiffness
![Page 21: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/21.jpg)
Allowable RAP in New Mix
Stiffness m-value Minimum*68.9 57.0 57.0 48.347.5 27.7 27.7 23.516.2 -1.6 -1.6 -1.4-22.0
Step 5 - Target Binder Grade v.s SRAP Binder Limit Percentage
Target binder low temp PG grade (°C)
-10.0
SRAP binder % LimitFresh Asphalt Binder: PG64-22 Calculation of percent RAP allowed in new HMA
-16.0
Percent binder in new mix 5.0Percent binder in RAP 5.91
‐1001020304050607080
‐22 ‐16 ‐10 ‐4 2Target Binder Low PG Grade (� )
SRAP Binder % Limit 1. Enter % AC in new
mix2. Select Target PG
Grade 3. Determine max
allowable RAP
S value limitM value limit
![Page 22: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/22.jpg)
Validation with artificial RAP
4.21.61.67.03.43.10.813.6240
4.42.82.65.35.24.91.418.6120
4.54.64.43.77.97.62.425.160
2.47.27.02.511.811.54.233.330
1.211.211.00.417.217.16.944.015
-1.916.116.4-2.223.624.210.955.68
Differ (%)TestedCalcul-
atedDiffer
(%)TestedCalcul-ated
Blended with 74.9% of freshBlended with 51.2% of freshFresh2PAVTime
(s)
![Page 23: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/23.jpg)
Unknowns – more work
•Effect of aging of binder RAP is not considered in this procedure– Will attempt aging mortars in PAV
•Temperature dependency is assumed to be same for blended and new binder– Can test mortar at 2 temps to verify
•Effect of RAP size blend – Work is underway to try several sizes
![Page 24: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/24.jpg)
Effect on other PG properties
• High temp grade – Work started on # 100 - #200 RAP in DSR – Using parallel plate ( 25-mm)
• Intermediate temp– DSR with new geometry will be tried – BBR at longer times
• Fracture at low temp– Device is underdevelopment (New BBR).
![Page 25: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/25.jpg)
Summary
• An initial procedure has been developed• Results appear reasonable • A few issues to be checked
– PAV aging of mortars – Temp dependency
• Future work – High and Intermediate Temp testing – Fracture
![Page 26: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/26.jpg)
The blending concept New binder is a PG 70-16 (TG PG70-20)
X
X
![Page 27: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/27.jpg)
Effect of blending time compared to PAV aging
![Page 28: Estimating Low Temperature PG-Grade of Binders in RAP](https://reader033.vdocuments.site/reader033/viewer/2022042302/625adb6d1a4e760a396987a1/html5/thumbnails/28.jpg)
Example of the problemRA
P Bi
nder
S(6
0)