EQS LIMIT AND GUIDELINE VALUES FOR CONTAMINATED SITES Report

2017

2

Table of Contents

CONTENTS

INTRODUCTION ............................................................................................ 4

EQS GUIDELINE VALUES IN SWEDEN ........................................................... 5

Soil ........................................................................................................................................ 5

Generic guideline values ............................................................................................................. 5

Dutch soil Intervention values ..................................................................................................... 7

Groundwater......................................................................................................................... 7

Surface water ....................................................................................................................... 8

Drinking water ...................................................................................................................... 8

Sediment............................................................................................................................... 9

Biota ..................................................................................................................................... 9

Discussion on EQS guideline values in Sweden .................................................................... 9

EQS LIMIT VALUES IN LATVIA .................................................................... 11

Soil and subsoil ................................................................................................................... 11

Surface and groundwater ................................................................................................... 16

Biota ................................................................................................................................... 17

COMPARISON OF EQS LIMIT VALUES FOR CONTAMINATED SITES IN

LATVIA WITH EQS LIMIT AND GUIDELINE VALUES IN ANOTHER

COUNTRIES (TERRITORIES) ....................................................................... 18

SHORT OVERVIEW OF RELEVANT POLLUTANTS IN LATVIAN

CONTAMINATED SITES ............................................................................... 25

3

EXPERIENCE OF THE PILOT SITES VISIT IN THE TERMS OF APPLYING EQS

LIMIT VALUES ............................................................................................. 29

Former black fuel storage facility of Valmiera city heating company ................................ 29

Former storage facility of mineral fertilizers and pesticides “Krustmaļi” (1960 – 1990) .. 34

Conclusions from pilot sites visit ........................................................................................ 38

DISCUSSION OF EQS LIMIT VALUES IN LATVIA ........................................ 40

CONCLUSIONS ............................................................................................ 41

REFERENCES ............................................................................................... 43

4

Introduction

This report has been developed within the EU-financed project INSURE. INSURE is a four year Interreg Central Baltic project running from September 2015 until August 2019. The project is a cooperation between seven partners from Sweden, Finland and Latvia. This report has been developed by The Latvian Environment, Geology and Meteorology Centre with support from the County Administrative Board of Östergötland regarding the situation for guideline and limit values in Sweden.

The report gives examples of what guideline and limit values that are used in Latvia and Sweden. The report also discuss how the values are used and how they are in comparison with values from other countries. The report focus on values for soil, groundwater, surface water, sediment and biota.

In order to identify if a site is contaminated or not, and perform a risk assessment for it, it is essential to have clear and scientifically based guideline or limit values of environment quality standards (EQS). However, approaches how to set guideline or limit values differs in different countries and territories. There are differences, in between countries, in the numeric values for the same pollutants and also between legal status of guideline and limit values.

In Latvia limit values are firmly established in national legislation, and foreign limit or guideline values can be used only in the case if there are no national limit values available.

In Sweden it is more common to use guideline values instead of limit values for soil. If there are no Swedish guideline values consultants can use other countries guideline or limit values for risk assessment. Before using guideline values it is important to consider if the value is applicable for the specific site.

In the next chapters some of the guideline and limit values that are used in Sweden and Latvia are described into more detail, a short comparison is given on limit and guideline values in different countries and territories. One part of the comparison is dedicated to the methodology aspect and how other factors, such as soil texture and type of land use are used and taken into account or ignored in different countries and territories.

To help understand the real situation with contaminated sites in Latvia, two additional chapters are included in the report: 1) an overview of relevant pollutants in contaminated sites in Latvia, and 2) findings of field visit of two Latvian contaminated sites, designated as pilot territories of different remediation activities of INSURE project from another project partners.

This report also contains references where the reader can find more information about the background to the different values and other issues, discussed in this report.

5

EQS guideline values in Sweden

Soil

Generic guideline values The Swedish Environmental Protection Agency (SEPA) developed a model to derive guideline values for contaminated land in 2009, SEPA report 5976 [19]. The model was used to calculate the Swedish generic guideline values. In 2016 the model was partly revised and new guideline values were set for some pesticides and organotin compounds, table 1 in Appendix 1. The Swedish generic guideline values for soil are based on normal conditions at contaminated sites in Sweden. The guideline values apply to dry soil. The generic values are intended to be protective of health and the environment at the majority of the contaminated sites. However they cannot be applied at all sites. In cases where the generic guideline values are not relevant to the conditions at a contaminated site site-specific guideline values can be calculated, which take into account the actual site conditions. The calculation program can be found at the SEPA web site [32]. Generic guideline values are not legally binding values. The guideline values are one of the tools used in risk assessments. In simplified risk assessment measured contaminant concentrations on site are compared with generic or site-specific guideline values. Guideline values, in the context of remediation of contaminated sites, are the contaminant concentration in soil under which the risk of harmful effects on human health, the environment or natural resources is acceptable. However, contaminant concentrations which exceed guideline values do not necessarily give rise to negative effects. The generic guideline values are intended to protect people living on or visiting the contaminated site. The assessment of health risks takes into account exposure caused by direct contact with the contaminated soil as well as indirect exposure which can occur by the transport of contaminants to air, groundwater and plants. The guideline values also take into account protection of the soil environment on the site. Groundwater and surface water are also protected against effects which occur as a result of the transport of contaminants. The final guideline value is the lowest of the values derived to protect the health, soil environment, groundwater and surface water. In addition, a number of adjustments of the guideline values are made in order to avoid acute toxic effects and the occurrence of free-phase organic contaminants in soil. Finally, the guideline values are checked to ensure that they are not lower than the background concentrations which occur naturally or which are a result of large-scale diffuse pollution.

An important part of the derivation of guideline values is the expected land use at the site. Land use determines the likely activities on the site and therefore determines which groups of people will be exposed to contaminants and to what extent exposure will occur. Land use also affects the degree to which protection of the soil environment is required on the site. The Swedish

6

generic guideline values have been derived for two different types of land use, sensitive land use (KM) and less sensitive land use (MKM). The land use controls the activities that can be assumed to occur on the contaminated site and therefore the groups of people that can be exposed and to what extent that can be assumed.

Sensitive land use (KM) means that the soil quality does not limit the land use. All groups of people, including children, adults and elderly, can stay in the area during a lifetime. Most of the ecological systems in the soil are protected and so are the groundwater and surface water. Sensitive land use generally corresponds to residential housing and parkland.

Less sensitive land use (MKM) is where soil quality limits the choice of land use to for example industries, offices or roads. The groups of people who are assumes to be exposed are people who are working on the site and also children and elderly who are temporarily visiting the area. The soil quality provides conditions for soil functions that are necessary for less sensitive land use, for example the ability for vegetation to grow and animals to temporarily stay on the site. Groundwater up to a distance of 200 meters and surface water are protected. Less sensitive land use generally corresponds to commercial and industrial land use.

The generic guideline values are calculated with some assumptions. They are based on the chemical form in which the substances are present in the soil and are expected to provide the greatest risk. They are also based on normal dense soils and are calculated for contamination in the soil above the groundwater table. When the SEPA generic guideline values are used in the investigation of contaminated sites one should also consider:

They do indicate a level of contamination under which the risk of harmful effects on human health, the environment or natural resources is normally accepted in the context of remediation. This does not necessarily mean that contaminant concentrations that exceed guideline values give rise to negative effects.

They are recommendations and one of many tools in the risk assessment of contaminated sites. They are not legally binding values.

They are calculated on national basis and for a great number of situations.

They do not indicate a level up to which it is acceptable to pollute.

They are not directly useful for other contaminated media such as sediment, building material etc.

They do not take into account synergies between contaminants.

When the generic guideline values are used on a contaminated site, the conditions for

distribution and exposure should not deviate significantly from the assumptions in the model.

7

Dutch soil Intervention values In cases where there is no Swedish generic guideline value there is a possibility to calculate site specific values using the model from the generic guideline values, see the chapter above regarding generic guideline values. But many times the consultants or authorities use guideline values from other countries instead, for example the Dutch soil Intervention values [4]. In Sweden the Dutch soil values have been used mostly for pesticides.

The Intervention values for soil indicate when the functional properties of the soil for humans, plants and animals are seriously impaired or in danger of being so. A contamination of soil above the Intervention values is deemed to be severe. The soil Intervention Values apply to dry soil. The soil Intervention values where first published in 2000, some of the values have been adjusted since then. More information about the Dutch Intervention values are to be found at the Ministry of Infrastructure and Environment website [33].

Groundwater

The Geological Survey of Sweden has general guideline values as well as trend reversal starting point values on national level for groundwater [34]. The guideline values and the trend reversal starting point values are for example used in the work for classifying groundwater according to the water framework directive. Some pollutants are subjected to these general guidelines for example some metals and chlorinated hydrocarbons, table 5 in appendix 1. The SEPA´s Criteria for Environmental Quality Assessments, first published in 1999, constitute a system of classification which facilitates the interpretation of environmental data. The system can be used to determine whether values are low or high in relation to either a national average or baseline readings. In most cases these assessment criteria are to provide a basis for the assessment of current environmental conditions. The Environmental Quality Criteria were included in the appendix of SEPA report 4918, Methods for inventories of contaminated sites. The report has also been translated in to English [10]. Since the Water Framework Directive was adopted these environmental quality criteria, mentioned above, have been updated and replaced. The Geological Survey of Sweden published a new report regarding groundwater quality criteria in 2013 [26]. The new environmental quality criteria for groundwater have been established for a wide range of substances. Substances which generally occur naturally in groundwater have a classification based on comparison with background values and possible environmental or health effects (1 – very low, 2 – low, 3 – medium, 4 – high, 5 – very high). For substances of probable anthropogenic origin an assessment has been made based on the magnitude of the impact (1 – no or insignificant impact, 2 – some impact, 3 – significant impact, 4 – large impact, 5 – very large impact), table 6 in Appendix 1. Since there are few guideline values regarding groundwater The Dutch groundwater Target and Intervention values [4] have been used in Sweden to evaluate contamination in groundwater, table 7 in Appendix 1. Just as in soil the groundwater values have been used for

8

pesticides and also chlorinated compounds. Groundwater target values are assuming there is a negligible risk for the ecosystem in a long term perspective. For metals there is a distinction between shallow and deep groundwater. The reason is that deep and shallow groundwater contains different background concentrations. More information about the Dutch Target and Intervention values are to be found at the Ministry of Infrastructure and Environment website [34]. In Sweden the petroleum companies formed an organization, SPIMFAB, which have worked with investigation and remediation of gas stations between the years 1997 to 2014. For that project they calculated guideline values for sites contaminated with gas and diesel products, table 8 in appendix 1. Those values can be used as reference when other sites are contaminated with hydrocarbons [21].

Surface water

The Swedish Agency for Sea and Water Management has regulations and limit values for classification and environmental quality standards for surface water [31]. The regulation is based on the Water Framework Directives with values for priority substances and national environmental quality standards. In comparison to several other European Countries Sweden also has limit values for sediments and biota to determine chemical classification of surface waters, table 2 in Appendix 1.

Drinking water

The National Food Agency in Sweden has regulations regarding drinking water [5]. These limit values can also be used to evaluate contamination of groundwater, table 9 in Appendix 1.

9

Sediment

There are no Swedish generic guideline values for contaminated sediments except for some substances that can be found in the regulations regarding surface waters [31], table 3 in Appendix 1. To be able to classify sediments other countries guidelines values are therefore often used in Sweden.

Canadian Sediment Quality Guidelines for the Protection of Aquatic Life, table 4 in appendix 1, are sometimes used in Sweden for evaluation of contaminated sediments. The guidelines are divided into two values, the lower value, referred to as Interim sediment quality guidelines (ISQGs) or TEL (threshold effect level) represents the concentration below which adverse biological effects are expected to occur rarely. The upper value, referred to as the probably effect level (PEL) defines the level above which adverse effects are expected to occur frequently. More information about how and when to use the different guideline values are to be found at the Canadian Council of Ministers of the Environment [3] and [6].

Norwegian Environmental Quality Criteria are also used in Sweden for risk assessment of sediments. The Norwegian Environmental Agency has for example Environmental Quality Criteria for sediments from I-V where I stand for Background and V for Severely bad [35].

Biota

To classify biota there is some guideline values in the table 3 in appendix 1 in the regulation regarding surface water [31]. EU also has regulations (1881/2006) on setting maximum levels for certain contaminants in foodstuffs. Information could for example be found regarding maximum levels in fish of a number of contaminants [15].

Discussion of EQS guideline values in

Sweden

Sweden has guideline values for contaminated soil but is missing generic guideline values for contaminated sediment. Although, the Swedish Agency for Sea and Water Management has regulations and some limit values for sediments to determine chemical classification of surface waters that can be used in the work with contaminated sediments. To have more specific Swedish guideline values for sediments could although support the work with risk assessments of contaminated sediments. Generally, for all medias, there are guideline or limit values missing for some substances or groups of substances. The work is although progressing and for example last year the Swedish Geotechnical Institute presented preliminary guideline values for PFAS (Perfluoroalkyl substances) for soil and groundwater. Since last year there is

10

also a proposal for guideline value and trend reversal starting point value regarding PFAS in groundwater. These values will be official during 2018.

A general comment although, both if using Swedish or other countries guideline values, is the importance of applying the relevant guideline value for a specific site or condition. The Swedish generic guideline values for soil cannot be applied at all sites, in cases where generic guidelines are not relevant, site specific guideline values can be calculated. Site specific guideline values are sometimes today calculated but the knowledge about the process could be improved both in general terms and for example regarding how to consider soil environment in the process.

11

EQS limit values in Latvia

Environment quality standards (EQS) in Latvia are divided by type of environment and there are different legislative acts that define EQS target, precaution and limit values for each type of environment.

Soil and subsoil

For soil and subsoil, there is Cabinet of Ministers Regulation No 804 “Regulation of the Quality Normatives for Soil and Subsoil”, issued on 25th October 2005 [14], which contains values of EQS (target, precaution limit and critical limit values) for certain amount of pollutants, depending from granulometric content of soil (or soil texture).

Granulometrically, soil can be composed from the particles with different size (Table 1).

Table 1. Classification of soil particles (soil texture) in Latvia Size of particles, mm Type of particles

<0.002 Clay

0.002...0.05 Silt

0.05...2.0 Sand

In reality, soil is mixture from differently sized particles, and soil type is identified from content of certainly sized particles from soil textural triangle (Figure 1).

12

Figure 1. Soil textural triangle

Regulation No 804 defines three types of EQS for soil and subsoil:

Target value EQS (A) shows the maximum concentration of pollutant of soil, exceeding of which leads to loss of sustainable quality of soil and subsoil;

Precaution limit value EQS (B) shows the maximum pollution level, exceeding of which leads to potential harm to human health and environment. Besides, pollution must to decreased to this level as the result of remediation, if there are no other special requirements;

Critical limit value EQS (C) shows the level of pollution, exceeding of which leads to serious disruption of functional properties of soil or direct harm to human health and environment.

Regulation also prohibits starting a new polluting activity on the soil, if the limit value (even of type B) is exceeded. If any of limit values has been exceeded, then, according to Law on Pollution, following measures should be carried out:

Exploration and monitoring of contaminated site, if EQS of precaution limit value (B) has been exceeded or EQS of critical limit value (C) is exceeded for type II (Table 3) pollutants in the sites, which were designated as hazardous by regional environmental board of State Environment Service;

13

Remediation of site, if the EQS of critical limit value (C) is exceeded.

Table 2. Soil and subsoil EQS limit values for type I pollutants (heavy metals, oil products, PAHs and PCBs) in Latvia (mg/kg)

Parameter Sand Clayous sand (sandy loam)

Sandy clay (loam) Clay

A* B** C*** A B C A B C A B C

Cu 4 30 150 7 40 150 12 50 150 19 60 150

Pb 13 75 300 13 100 500 16 200 500 23 200 500

Zn 16 250 700 24 250 700 46 350 700 70 350 700

Ni 3 50 200 8 75 200 16 75 200 28 100 200

As 2 10 40 2.5 10 40 3 15 40 5.5 20 40

Cd 0.08 3 8 0.09 3 8 0.18 4 10 0.2 4 10

Cr 4 150 350 11 150 350 22 170 350 40 170 350

Hg 0.25 2 10 0.54 2 10 0.8 3 10 0.8 3 10

Sum of oil products

1 500 5000 1 500 5000 1 500 5000 1 500 5000

Sum of PAHs (10 cmpnds)

1 12 40 1.2 15 40 1.2 18 40 1.5 20 40

Sum of PCBs

0.02 0.1 1 0.02 0.1 1 0.03 0.2 1 0.05 0.2 1

*A – target value EQS **B – precaution value EQS ***C – critical value EQS

It is obvious that EQS values for soil and subsoil are more tolerant for soils with higher content of clay and less tolerant for soils with higher contents of sand, what can be explained by capability of clay to immobilize certain pollutants (mostly metals and oil products). However, granulometric composition of soil plays no role in the case of pollutants of type II (Table 3):

14

Table 3. Soil and subsoil EQS limit values for type II pollutants in Latvia (mg/kg) Pollutants Target value EQS (A) Critical value EQS (C)

Inorganic Compounds

Free cyanides 1 20

Cyanide complex (pH<5) 5 650

Cyanide complex (pH≥5) 5 50

Aromatic Hydrocarbons

Benzene 0.01 1

Ethylbenzene 0.03 50

Toluene 0.01 130

Sum of Xylenes 0.1 25

Sum of Phenols 0.05 40

Sum of Cresols 0.05 5

Chlorinated Organic Compounds

Vynilchloride 0.01 0.1

Dichloromethane 0.4 10

1,1-Dichoroethane 0.02 15

1,2-Dichloroethane 0.02 4

1,1-Dichloroethene 0.1 0.3

1,2-Dichloroethene 0.2 1

Dichloropropane 0.002 2

Trichloromethane 0.07 15

1,1,1-Trichloroethane 0.07 15

1,1,2-Trichloroethane 0.4 10

Trichloroethene 0.1 60

Tetrachloromethane 0.4 1

Tetrachlorethene 0.002 4

Sum of Chlorobenzenes 0.03 30

Sum of Chlorophenyls 0.01 10

Pesticides

Sum of DDT, DDE and DDD* 0.01 4

Sum of drins (Aldrin, Dieldrin, Endrin) 0.005 4

Sum of Hexachlorohyclohexane compounds 0.01 2

Atrazine 0.0002 6

Carbaryl 0.00003 5

Carbofuran 0.00002 2

2-methyl-4-chlorophenoxyacetic acid (MCPA) 0.00005 4

Other Pollutants

Cyclohexane 0.1 45

*DDT – Dichlorodiphenyltrichloroethane, DDE – Dichlorodiphenyldichloroethylene, DDD – Dichlorodiphenyldichloroethane.

Although it is not clearly stated in the regulation No 804 but just like in Sweden, EQS limit values in Latvia:

Should not be considered as the limit up to which it is allowed to pollute;

Are not directly useful for assessment of another polluted media, such as sediment, building materials etc.;

As it can be seen from the Table 2 and Table 3, EQS limit values for different pollutants in Latvia are not dependant of each other, i.e. there is no consideration of the effect of their synergy.

Regulation No 804 states that depth of soil sample taking is 25 cm. If the layer of humus accumulation is thinner, the sample should be taken in the depth of the layer, but no shallower than 10 cm.

15

The average sample of the soil should be taken by mixing not less than 25 individual samples, taken evenly from the area to be tested. However, the area to be tested shouldn’t be larger than 5 hectares. To estimate the level of contamination of subsoil in the sites, where the source of pollution is migration of contaminated groundwater, the samples of subsoil must be taken with 50 cm interval in the entire depth of prevalence of the contaminated groundwater (including zone where level of groundwater fluctuates). The regulation No 804 state clearly that EQS limit values refer to sample in form of dry solids only for heavy metals. For other pollutants this factor remains unclear. For example, so called “Dutch list”, or the document “Annex A: Target values, soil remediation intervention values and indicative levels for serious contamination” [4], unlike the Latvian regulation, clearly states that all of its EQS limit values refer to content of pollutants in the dry solids. There is no wide practice to use foreign EQS limit values in the Latvia. Only in cases, when there are pollutants, for which national EQS limit values are not available it is justified to use limit values from other countries.

16

Surface and groundwater

For surface and groundwater, there is Cabinet of Ministers Regulation No 118 “Regulation on the Quality of the Surface Water and Groundwater”, issued on 12th March 2002 [11]. This document mostly deals with EQS target and limit values for both priority substances and biogenic pollutants for surface water (dividing it into salmonid or cyprinids fish waters) and in groundwater, including limit values for water, deemed for abstraction as drinking water. EQS limit values for priority substances are harmonized with EU legislation – i.e., Directive 2013/39/EU “amending Directives 2000/60/EC and 2008/105/EC as regards priority substances in the field of water policy” [27]. However, it contains EQS target and limit values for contaminated sites either, as well as EQS requirements for remediation of groundwater in the contaminated sites. Its summary is showed in Table 4.

Table 4. EQS for groundwater in contaminated sites and its comparison with EQS for drinking water abstraction in Latvia

Parameter Unit or measurement

Groundwater in

contaminated site

Ground-water limit value for

abstraction as drinking

water

Quality requirements for surface water

deemed for abstraction as drinking water

Requirement for minimal reduction of pollution in

result of remediation, % Target

value Limit value

Target value

Limit value

COD mg O2/l 40 300 30 75

Ntot mg/l 3 50 3 80

Synthetical surfactants

µg/l 200 500* 80

Phenol index µg/l 0.5 50 10 100 60 – 70

Oil products (C10 – C40)

mg/l 1 0.5 1 60 – 70

Benzene µg/l 0.2 5 1 2 60 – 70

Ethylbenzene µg/l 0.5 60 60 – 70

Toluene µg/l 0.5 50 60 – 70

Xylenes µg/l 0.5 60 60 – 70

Cu µg/l 10 75 2000 1000 60 – 70

Cd µg/l 1 6 5 1 5 60 – 70

Pb µg/l 10 75 10 50 60 – 70

Hg µg/l 0.05 0.3 1 0.5 1 60 – 70

Cr µg/l 10 30 50 50 60 – 70

Co µg/l 10 100 60 – 70

Ni µg/l 10 75 20 20 60 – 70

As µg/l 10 60 10 50 100 60 – 70

Mo µg/l 10 300 60 – 70

*Which reacts with methylene blue, µg/l Sodium Dodecylbenzenesulfonate.

Paradoxally there are some EQS for groundwater in contaminated sites that are more stringent than EQS for surface and groundwater deemed for abstraction as drinking water. This is a result of historical implementation of different European directives, regulating various aspects of water protection and use.

It should be noted as well, how Regulation No 118 in Point 26 defines application of EQS limit values for groundwater in the contaminated sites, and it is:

17

If level of pollution has exceeded the mean arithmetic value between target and limit value, then boundaries of pollution plume must be determined, potential risk to human health and environment must be assessed and activities should be taken to avoid the spreading of pollution.

If level of pollution has exceeded the limit value it should be evaluated if remediation of the site is necessary and if it is possible to carry it out without potential risk to human health and environment, taking into account geological, hydrogeological and hydrodynamic factors and anthropogenic pressure in site, as well as if the costs of planned remediation and control (monitoring) are reasonable enough. On the basis of assessment carried out deemed treatment level of groundwater for each site should be assigned individually and remediation should be performed according to the Law on Pollution [7].

Biota

For biota, there is the same Cabinet of Ministers Regulation No 118 [11], which was mentioned above regarding the EQS limit values for surface and ground water. Table 3 of Annex I of Regulation defines EQS limit values for certain pollutants (Table 5). If not stated otherwise, default EQS limit values are given for fish and they mean maximum allowed concentration of pollutant in the soft tissue of the water organisms without drying.

Table 5. Latvian EQS limit values for certain pollutants in biota (µg/kg) Pollutant CAS number EQS limit

value

Bromdiphenylethers 32534-81-9 0.0085

Fluoranthene 206-44-0 30*

Hg 7439-97-6 20

Hexachlorobenzene 118-74-1 10

Hexachlorobuthadiene 87-68-3 55

Benz-(a)-pyrene 50-32-8 5

Dicofol 115-32-2 33

Perfluorooctanesulfonic acid (PFOS) and its derivatives

1763-23-1 9.1

Dioxines:

0.0065** TEQ

7 Polichlorodibenzo-p-dioxines (PCDD)

1746-01-6, 40321-76-4, 39227-28-6, 57653-85-7, 35822-46-9, 3268-87-9, 19408-74-3

10 Polichlordibenzofurans (PCDF)

51207-31-9, 57117-41-6, 57117-31-4, 70648-26-9, 57117-44-9, 72918-21-9, 60851-34-5, 67562-39-4,

55673-89-7, 39001-02-0

12 Polichlorinated Biphenyls, similar to Dioxine

32598-13-3, 70362-50-4, 32598-14-4, 74472-37-0, 31508-00-6, 65510-44-3, 57465-28-8, 38380-08-4, 69782-90-7, 52663-72-6, 32774-16-6, 39635-31-9

Hexabromocyclododecanes (HBCDD)

25637-99-4, 3194-55-6, 134237-50-6, 134237-51-7, 134237-52-8

167

Heptachlor and Heptachlor epoxides

76-44-8, 1024-57-3 0.00067

*EQS is set for crustacea and molluscs. **EQS for fish, crustacea and molluscs, accordingly to EU Commission Regulation No 1259/2011 regarding content limits of Dioxines and PCBs in the food.

18

Despite of the availability of EQS limit values for biota, there is no wide practice in Latvia to

use biota as indicator to identify the contaminated site. However, biota is sometimes used as

indicator of water quality in the surface water bodies, as part of river basin management

plans.

Comparison of EQS limit values for

contaminated sites in Latvia with

EQS limit and guideline values in

another countries and territories

The EQS for soil in contaminated sites are applied differently in Latvia and in other countries. In Latvia, EQS limit values depend from soil texture (or granulometric content), while in another countries it mostly depends from land use classification. Most typical classification, which can be found regarding EQS limit or guideline values for contaminated sites, contains following types of land use;

agricultural land,

residential/parkland,

commercial land,

Industrial land.

This classification seems to be developed considering potential pathways of pollutants from contaminated sites to human body as well as access of the population to certain type of land and possible type of exposure to the pollutants.

Generally, people can be exposed to contaminants in soil through ingestion (eating or drinking), dermal exposure (skin contact) or inhalation (breathing). The route of human exposure to a soil contaminant will vary with the contaminant and with the conditions and activities at a particular site.

Many people, especially children, accidentally ingest small amounts of soil as part of their normal activities, such as performing yard work, gardening or playing. Young children usually ingest more soil than older children and adults because of their frequent hand-to-mouth behaviour. Children and adults may also ingest soil while indoors if soil is transported into homes or other buildings, such as on shoes, clothing or pets. Some contaminants, such as many pesticides, can pass through the skin and enter the body. People may also inhale contaminants bound to soil particles that become airborne (such as in windblown dust), or contaminants that vaporize from soil.

People can be exposed to contaminants in soil particles that stick to edible parts of garden produce or get taken up into garden plants from the soil. Animals raised for food may also take

19

in contaminants from soil, and people may be exposed to these contaminants by eating animal products such as meat, eggs and milk. Drinking water may contain contaminants that were directly discharged into the water source or entered the surface water through runoff, or had leached from the soil into groundwater. In some situations, a contaminant may vaporize from the underlying groundwater and become part of the air that people breathe [20].

Thus, it is rather obvious that certain types of territories (i.e. agricultural and residential/parkland territories) are much more sensitive to potential contamination, unlike the other type of territories, where people are spending less time, where children do no play, or territory even has limited access – i.e., only authorized staff can enter and stay there.

Properties of each type of land use can be summarized in the following table (Table 6):

Table 6. Typical land use classification regarding EQS for contaminated sites Type of land use Potential pathway of

pollutants into human body Level of accessibility Potential

exposure time

Agricultural Ingestion Indirectly high Long

Residential/parkland Skin contact, ingestion High Moderate long

Commercial land Skin contact, inhalation Moderate Moderate

Industrial land Skin contact, inhalation Low (restricted territories, only authorized personell allowed)

Short

Comparing approaches – the Latvian approach (using soil texture as factor for EQS limit values and not using type of land use) is not unique. However, soil texture, from the countries reviewed in this analysis, is much less popular factor than type of land use. Comparison is shown in the following tables:

Table 7. Distribution of countries depending of use soil texture as factor to establish EQS limit or guideline values for contaminated sites or soil

Taking into account soil texture Not taking into account soil texture

Latvia

Germany

Denmark

Sweden

United Kingdom

Netherlands

Norway

Canada

Texas (USA)

Russia

Kazakhstan

Republic of South Africa

Nigeria

Table 8. Distribution of countries depending of use type of land use as factor to establish EQS limit or guideline values for contaminated sites

Taking into account type of land use Not taking into account type of land use

Sweden

Denmark

Germany

Nova Scotia (Canada)

Canada

Texas (USA)

Republic of South Africa

Nigeria

Latvia

Netherlands

Russia

Kazakhstan

20

As stated above, it is easy to understand that agricultural land and residential/parkland are more sensitive to potential contamination than commercial or industrial land. Therefore, EQS limit or guideline values for contaminated sites are more stringent for agricultural land than for residential or parkland, and EQS for industrial land allows higher level of contamination than for commercial land. As higher is risk for pollution pathway and exposure, as stringent should be the corresponding EQS limit values.

Land use classification exists in Latvia, however, it has minor differences with the typical classification described above and at the moment it does not affect EQS limit values for contaminated sites in Latvia. Classification of land use in Latvia exists in Cabinet of Ministers Regulation No 305 “Regulation on the cadastral valuation”, issued 18th April 2006 [16], and in the Cabinet of Ministers Regulation No 240 “General regulation on the planning, use and construction in the territory”, issued 30th April 2013 [28]. The first regulation lists the type of land use or zoning as follows:

Zone of the agricultural land;

Zone of forest land;

Zone of residential housing;

Zone of industrial installations;

Zone of commercial housing.

The second one gives a more detailed breakdown of the land use types or functional zones:

Individual residential housing;

Low-rise residential housing;

Multi-storey residential housing;

Mixed downtown housing;

Public building territory;

Industrial territory;

Transportation infrastructure territory;

Technical installations territory;

Territory of nature and parkland;

Forest territory;

Agricultural territory;

Surface water.

To harmonize various types of land use classification, the following transitional table was proposed in the terms of this project. However, the further decisions to adapt it in national legislation will depend from the competent institutions in the field of soil protection, classification and quality policy in Latvia (Ministry of Environment Protection and Regional Development etc.).

21

Table 9. Proposed transition table of various classification of land use types Typical land use classification Latvian zoning types Latvian types of functional zones

Agricultural Agricultural land Agricultural territory

Residential/parkland Residential housing Individual residential housing

Low-rise residential housing

Multi-storey residential housing

Forest land Territory of nature and parkland

Forest territory

Surface water

Commercial land Commercial housing Mixed downtown housing

Public building territory

Transportation infrastructure territory

Industrial land Industrial installations Industrial territory

Technical installations territory

Although this transitional table seems to be clear and logic enough, it is only a proposal and it may appear simpler than it is and some positions in the table can still be questioned if they are classified correctly.

For example, territory of nature and forest territory in the Latvian understanding are not exactly the same as residential/parkland in foreign classification, since territories of forest and nature in Latvia are very different and wide by their nature, differing a lot by accessibility and frequency of human presence. Some problems also exist with correct classification of transportation infrastructure territory – for example, highway or railway especially stretches with low or very low density of traffic, which easy can be accessed by people passing or children playing. It usual deal to transport oil products by railway in Latvia, and contamination of railway roads by leaking oil products is highly possible.

However, even with this transitional table (i.e. Table 9) it is impossible to compare Latvian and foreign EQS directly. Thus, the only way to compare them is to compare the intervals for certain pollutants, not taking into account soil texture (unless it is possible) and type of land use.

Also, taking into account there are present different types of EQS (for example, target values, precaution values, limit values and guideline values, which cannot be compared directly), it should be noted that this comparison at this stage is only to get a short insight how scattered and different each from other these EQS values really are. It should be also taken into account, that some foreign values can be only the proposed draft limit values or even maybe old and outdated standards. Proper and scientifically based comparison of EQS for the same conditions (soil texture, land use type, type of EQS) will request much deeper analysis, which is beyond scope of this analysis.

22

Table 10. Comparison of EQS limit or guideline value intervals for heavy metals in the soil of the contaminated sites in different countries (mg/kg)

Country (or region)

As Cd Cr Cu Pb Hg Zn Ni

Latvia [14] 2...40 0.08...10 4...350 4...150 13...500 0.25...10 16...700 3...200

Denmark [12]

2...20 0.03....5 1.3...1000 13...500 10...400 0.04...3 10...1000 0.1...50

Netherlands [4]

29...55 0.8...12 100...380 36...190 85...530 0.3...10 140...720 35...210

Germany [9]

50 0.4...20 30...400 20...60 40...400 0.1...20 60...200 15...70

United Kingdom [9]

10 1 25 - 500 1 - -

Norway [9] 20 1 100 - 50 1 - -

Sweden* 10...25 0.8...12 80...150 80...200 50...400 0.25...2.5 250... 500

40...120

Russia [18] 2...10 0.5...2 6 55...132 30...130 2.1 55...220 85

Kazakhstan/ Kirgizstan [29]

2 2 - 3.5 35 2.1 23 6.7

Japan [1] 15 - - 125 - - - -

Republic of South Africa [24]

48...150 32...260 - 2300... 19 000

230... 1900

1...6.5 19 000... 150 000

1200... 10 000

Nigeria [22] 200...625

100...380 20...240 0.3...10 35...600 85...530 1500 140...720

Texas, USA [36]

24...200 52...800 33 000... 120 000

1300... 94 000

500... 1600

3.6...6.2 9900... 25 000

840... 8800

Nova Scotia, Canada [30]

31 1.4...2090 220... 6700

1100... 20 000

140... 8200

6.6...690 5600... 47 000

330... 2200

Quebec, Canada [2]

5...15** 0.9...1.5** 45...85** 40...100** 30...50** - - 30...100**

*Table 1 of Appendix 1 **Background levels

Table 11. Comparison of EQS limit or guideline values for organic pollutants in the soil of the contaminated sites in different countries and territories (mg/kg)

Country (or region)

Sum of PAHs Sum of PCBs

Sum of oil products

Sum of DDD, DDT and DDE

Drins (Aldrin, Endrin, Dieldrin)

Latvia [14] 1...40 0.002...1 1...5 000 0.01...4 0.005...4

Denmark [12] 1.5...15 - 25...100 1 -

Netherlands [4] 1...40 0.002...1 - 0.01...4 0.005...4

Sweden* 1...20 0.008...2 3...1 000 0.1...1 0.02...0.18

Republic of South Africa [24]

33...15 290 0.61...11 47 400...767 400 - -

Nova Scotia, Canada [30]

34 100...60 400 22...33 - 220...1 600 16.8...218

Texas, USA [36] 1 869...19 290 1.1...7.7 - 29.4...274 9.155...202.2

*Table 1 of Appendix 1

Unfortunately, there are lot of organic pollutants and within limited resources of this project it is impossible to perform a deep and detailed study for all of them. Thus, only few pollutants were analysed.

It is obvious, that different countries use different EQS values, and it seems that there is not only slight differences (as, for example, with Latvia and Denmark, where EQS values although

23

are not exactly the same, but at least are comparable), but rather different methodology or understanding of what EQS for contaminated sites is (for example, Republic of South Africa, Texas (USA), and Nova Scotia (Canada) have very different EQS limit or guideline values for contaminated sites, what most likely means that approach to estimate EQS in these countries or territories differs a lot from approach in another countries) as well.

Even the fact of Latvia, Denmark, Netherlands, Sweden, United Kingdom (UK) and Germany all are European Union member states, does not mean there is a harmonized EQS limit or guideline values, mostly due to EU Soil Directive has not been issued and adopted yet.

It is normal that there are inconsistencies for the lower values of the same pollutant in the different countries – since there can be target and/or background values presented for one country, while there can be precaution or the lower limit values for another country; such values can’t be compared and there is nothing wrong if they differ.

It should also be taken into account that type of land use commonly plays a significant role in establishing EQS limit or guideline values. And in the countries or territories where EQS limit or guideline values are established depending on land use type (as, for example, in Sweden), it may not be connected directly with the thresholds to achieve in the result of remediation. And EQS limit or guideline values are rather viewed as thresholds, prohibiting to use contaminated territory for specific purpose. For example, contaminated site with certain level of pollutants can be not suitable to be used as residential or parkland territory, but it still can be safe enough to be used as industrial territory. However, the largest values, considered to be direct “limit values” in most of countries, or the “worst scenario”, should be rather comparable though. Thus, the limit values (i.e., largest EQS values) for Lead in Latvia, Sweden, Denmark, Netherlands, UK and Germany are quite close (400 – 530 mg/kg) – especially, considering the dependence on soil texture and land use type as well. That is, Latvian EQS limit value for lead can vary from 300 to 500 mg/kg depending is the soil texture dominated by the sand or the clay. But Lead limit values in Texas (USA), Republic of South Africa and Nova Scotia (Canada) are certainly out of range with corresponding limit values of 1600, 1900 and 8200 mg/kg. That is – it seems that site in the same conditions can be viewed as “contaminated” in one country, while being perfectly safe in the other! Especially suspicious are EQS limit values, exceeding such levels as 100 000 mg/kg. For example, there is EQS limit value as high as 150 000 mg/kg for Zinc in Republic of South Africa, which can be recalculated as 150 g/kg, or 15% of Zn content in the soil. The same goes for limit value for oil products in the same country, with “worst scenario” limit value 767 400 mg/kg or up to almost 77% of oil product content in the soil sample, what appears to be not credible, since sample with such content of oil products most likely will be sandy oil, not oily sand, hardly possible to be called “soil”. For comparison, in one of the top contaminated sites in Latvia (former military airfield “Rumbula” near Riga), where research of contaminated site was performed, and content of oil products in the soil was found to be up to 23 000 mg/kg [17]. Another interesting observation, it appears that European countries in general tend to have more stringent EQS limit or guideline values than countries for another parts of world (i.e. America, Africa etc.). Latvia also has one of the most stringent EQS limit values for contaminated sites.

24

One of possible explanation is that some of EQS, mentioned in this short analysis, is too stringent, while other ones are too tolerant. Another explanation can be that methodologies on how to evaluate or identify the contaminated site in different countries differ a lot. For example, some of EQS limit values definitions are strongly connected with toxicological properties of the pollutants, and it seems that EQS limit values sometimes are established according to the toxicity of the pollutant, taking into account that accidental ingestion of soil could happen. As already mentioned before, it is not always clear, whether EQS limit or guideline value refers to content of pollutant in the dry solids or in the naturally wet sample. This can be one of possible explanations of obviously different approaches in establishing of EQS limit or guideline values. The brief overview of the requirements for the type of sample is shown in the following Table 12: Table 12. Requirements for soil sample type in different countries

Countries (regions), clearly stating to use dry solid sample

of the soil

Countries, at least partly referring to dry solid sample of

the soil

Countries with no clear requirements regarding soil

sample

Netherlands

Sweden

Denmark

Nova Scotia, Canada

Latvia

Germany

Norway

United Kingdom

Republic of South Africa

Russia

Texas, USA

It is not the aim of this project to judge, which methodologies or EQS values are more correct and more scientifically based – rather it is to pay attention and raise the problem that large differences in the field of EQS limit and guidance values for the contaminated sites exist.

25

Short overview of relevant pollutants

in Latvian contaminated sites

To identify most important Latvian EQS limit values, the list of relevant or “most popular” pollutants was made from the existing records of Latvian contaminated sites register (PPPV). However, it should be noted, that following analysis is limited by a few shortcomings:

Most of data collected are old and can be outdated at the moment especially taking into account that updates of site status change due to completed investigation or remediation sometimes arrives to PPPV register with a considerable delay;

Only small part of contaminated site records has information about type of pollutant present in the site (i.e., from total number of 3572 contaminated and potentially contaminated sites only 115 contains information about pollutants in soil and 242 – about pollutants in water [39]);

It should be noted, that deeper study and inventory of all contaminated sites in Latvia can change the following list dramatically.

However, even this limited statistics can give an insight of pollutants, found in the Latvian contaminated sites.

Table 13. Known pollutants in the soil of the Latvian contaminated sites Pollutant Number of contaminated sites

Oil products 94

Pb 22

Cu 17

Zn 15

Ni 8

Cr(VI) 8

Cd 6

Oil product waste 6

As 3

Hg 2

DDT 1

Metals 1

Spirits and Phenols 1

End of life vehicles 1

26

Table 14. Known pollutants in the water* of the Latvian contaminated sites Pollutant Number of contaminated sites

Oil products 178

Chemical Oxygen Demand 61

Total Nitrogen 27

Chlorides Cl- 15

Ammonium NH4+ 15

Biochemical Oxygen Demand 13

Pb 13

Zn 13

Anions 12

Oil product waste 11

Surfactants 11

Spirits and Phenols 10

Cu 5

Ammonia NH3 5

Cr(VI) 4

Phenol index 4

Ni 4

Total Phosphorus 4

As 3

Sulphates SO42- 3

Cd 2

DDT 2

Phosphates PO43- 2

End of life vehicles 2

Agrochemical waste 1

Fluorides F- 1

Hg 1

Creosote 1

Animal manure 1

Mn 1

Sodium alkyl sulphate 1

*It is not specified is it surface water or groundwater

PPPV register contains also information about pollutants, which have been stored in the territory of the contaminated or potentially contaminated site. In this case there is more information available than in the case of pollutants in the soil or water, however it still covers only smallest part from the total number of sites registered. 1397 contaminated or potentially contaminated sites of total 3572 have been reported on having stored certain pollutants (Table 15).

27

Table 15. Number of contaminated sites where particular pollutants have been stored historically in Latvia

Pollutant Number of contaminated sites

Oil products 679

Agrochemical waste 258

Municipal waste 199

Animal manure 113

Oil product waste 69

Gasoline 32

Ammonia NH3 27

Pesticides 12

Sewage sludge 11

Paint, lackuor, ink and glue waste 11

Spirits and Phenols 10

Animal and plant waste 8

Metal compounds 8

Acid waste 7

End of life vehicles 7

Oil and emulsion sludge 6

Waste electric and electronic equipment 6

Haloginated hydrocarbons and PCBs 5

Non-metallic compounds 5

Sulphates SO42- 5

Sulphuric acid H2SO4 4

Cr(VI) 3

DDT 3

Mixed chemical waste 3

Ni 3

Phosphates PO43- 3

Surfactants 3

Asphalt and bitumen waste from road construction 2

Cu 2

Chlorides Cl- 2

Nitric acid HNO3 2

Timber waste 2

Excavated contaminated soil 2

Alkalis and salts waste 2

Solvent waste 2

Zn 2

Amines 1

Anions 1

As 1

Phenol index 1

Hg 1

Lindane 1

Scrap metal 1

Sodium alkyl sulphate 1

Oil solvent 1

Ammonium NH4+ 1

Nitrates NO3- 1

Pb 1

Turpentine 1

White spirit 1

28

Not all pollutants in these lists have EQS limit values established or even need such values, especially many pollutants listed in the “historically stored” list. For example, there never will be EQS limit values for such “pollutants” as end of life vehicles, waste electric and electronic equipment, animal manure and agrochemical waste, and sites, reportedly being contaminated with these and similar types of pollutants, most likely should and will be eventually inventoried to specify the exact type of pollutant. Also, presence of certain type of waste in the site can give a clue to identify specific pollutants in the soil or in the water or groundwater. However, even this information is not always available – as it can be guessed from the fact that most of sites, registered in Latvia, do not have any information on type of pollution present. Mostly only type of facility or economic activity is known for contaminated or potentially contaminated site.

However, if rely on this limited statistics on pollutants, present in contaminated and potentially contaminated sites in Latvia, it is possible to generalize that most priority pollutants in the soil of contaminated sites are oil products and heavy metals, and, occasionally, pesticides as well.

Also, this chapter raises another question - can a site be viewed as contaminated if it contains only pollutants that are not included in the national pollutant list for contaminated sites? I.e., is the Latvian methodology, used in practice to identify contaminated site, consistent and uncontroversial?

29

Experience of the pilot sites visit in

the terms of applying EQS limit

values

During field visit of two contaminated sites in Latvia, selected as pilot sites for deeper study and remediation by another Latvian project partners (Valmiera city municipality and Vidzeme Planning Region) – former black fuel (mazut) storage facility of Valmiera city heating company on the Dzelzceļa street and former storage facility of mineral fertilizers and pesticides “Krustmaļi”, following observations were made.

Former black fuel storage facility of Valmiera

city heating company

Pilot site is located just north of individual residential houses (Figure 5). According to one assumption of this pilot area [37], the groundwater in this area flows roughly from north to south (Figure 6), i.e. in the direction of nearby residential housing (however, modelling done by LAMO Hydrogeological Model [40], gives a different direction of groundwater flow – from south-east to north-west (Figure 7). Although the heavy fractions (i.e. black fuel) of oil products have a low mobility in the environment and trend to be bound on the surface of soil particles, certain degree of pollution spreading risk still remains, since black fuel also has a trend to form stable emulsions with water. Moreover, heavy oil products, including black fuel, contain higher levels of polyaromatic hydrocarbons (PAHs) than lighter fractions of oil products and PAHs have better solubility in water than linear hydrocarbons (alkanes) [13]. Despite of groundwater flow rate being relatively slow (i.e. measured in meters per year), the long age of polluting activity and pollution presence in site means that it had enough time to spread. If the first assumption regarding direction of groundwater flow is true and remediation would be applied to this pilot site, it could be case, where application of different EQS limit values for contaminated site itself (black fuel former storage facility) and nearby residential area would be reasonable, due to their different sensitivity to pollution. However, it is and remains only “thought experiment”, because, as already stated, there is no distinction of EQS limit values for contaminated sites depending of land use type in Latvia.

30

Figure 2. View on the former former black fuel storage facility of Valmiera city heating company (photo from site visit in October, 2016)

Figure 3. Remains of semi-liquid black fuel in the bottom of reservoir (photo from site visit in

October, 2016)

31

Figure 4. Residue of black fuel mixed with rain water near railroad branch for unloading of

black fuel (May 2016)

32

Figure 5. Rough scheme of pilot area of contaminated site – former black fuel storage facility of Valmiera city heating company. Inside blue line is contaminated site itself with buildings

and fuel storage reservoirs. Territory inside orange line is a neighbouring residental housing, red line – rough distance measurement from the approximate border of contaminated site

(i.e. fence of storage facility, since exact boundaries of pollution plume is unknown yet) to the well in the nearby housing. The distance between dots is 45 meters. Aerial photo from

www.balticmaps.eu [41]

33

Figure 6. Planned boreholes for soil and groundwater sample taking in the Valmiera black oil fuel storage facility pilot area. Arrow shows potential direction of groundwater flow,

suggested by consultants [37]

34

Figure 7. Different estimation of direction of groundwater flow (red line) from the pilot site from contaminated site (orange area) to the nearby river [40]

Former storage facility of mineral fertilizers

and pesticides “Krustmaļi” (1960 – 1990)

Pilot site was once storage building (Figure 8), located on the roadside, surrounded from the other 3 sides with arable land (Figure 9 and Figure 10). At the moment the building is demolished (Figure 11), and soil contamination with pesticides (DDT/DDE/DDD) was detected (in 2012 [23]). During the site visit in the October 2016, the crops in the field around the location of sites still were grown (Figure 13). In this case too, out of the boundaries where the building stood, and where crops are grown now, it would better to cultivate only technical crops (energetic corn or rapeseed, grown as biomass for production of biogas in the digesters or production of bio-diesel), or to ensure that soil is safe enough to cultivate crops for food. Especially taking into account that according to information available, pollution plume already protrudes out of boundaries where the building once stood (Figure 12). EQS limit values designated for agricultural land would be helpful in this case.

35

Figure 8. “Krustmaļi” agrochemical storage building (2012)

Figure 9. Google Streetview image on the “Krustmaļi” site from the nearby main road

(September 2011, [42]). Storage building is still standing and crops can be seen growing in the field

36

Figure 10. Location of “Krustmaļi” site (roughly marked with blue). Red circle on the road is place from the Google Streetview image (Figure 9) was taken [42]. It can be seen that site is

surrounded by the agricultural land

Figure 11. Building demolished, floor and debris left. Sight very similar to that what was observed in the site visit in October 2016. Crop field and main road can be seen in the

background

37

Figure 12. Scheme of “Krustmaļi” site, with pollution areal marked (pink area – during site visit its boundaries were found to be marked with flags), samples with soil pollution detected (red triangles), samples with no pollution detected (green triangles), and rough marking of

auxiliary road (brown lines). This scheme shows that area of pollution protrudes out of boundaries of former building and intrudes into the surrounding agricultural land [38]

38

Figure 13. View on “Krustmaļi” site from the near crop field. Part of crops are located in the contaminated part of the land (photo from field visit in October 2016)

Conclusions from pilot sites visit

Taken into account this information, available from partner pilot projects and site visit, the following conclusions can be made:

In the terms of EQS limit value analysis, both pilot sites were chosen randomly – i.e. it was opportunity to visit these sites and get additional information regarding them because activities from other project partners were performed there. Despite of that, both pilot areas turned out to be located nearby the sensitive territories – i.e. residential housing in one case and agricultural land in the other, what means it could be more or less typical cases in the Latvia.

In both cases spreading of pollution in the direction and into territory of sensitive neighbouring areas were either already proven (site “Krustmaļi”) or likely to a certain degree (former black fuel storage facility of Valmiera city heating company).

Since both sites are designated as pilot territories for remediation activities, and there are no EQS limit values depending of land use type in Latvia, it means that as the successful result of remediation, the soil directly in the contaminated site (i.e. in the point of pollution source) and soil in the impacted sensitive area should be remediate up to the same level. It is not an optimal solution, since it would mean that either EQS limit values are too stringent for the industrial territories, where higher pollution levels could be allowed (and it would also mean higher costs of remediation), according to approach in many other countries, or that they are too tolerant for sensitive areas and in that case the threat for environment and/or human health would not be removed completely.

39

According to Cabinet of Ministers Regulation No 483 “Procedure of identification and registration of contaminated and potentially contaminated sites”, issued on 20th November of 2001 [8], if the contaminated or potentially contaminated site is located near a sensitive territory, it gets more risk points in the process of its assessment. However, presence of sensitive territory nearby does not affect the EQS limit values for contaminated site in Latvia.

40

Discussion of EQS limit values in

Latvia

Only small part of contaminated and potentially contaminated sites in Latvia listed in the PPPV register has been identified with pollution present in soil, water or have been stored in the site historically.

As far as it can be assessed from the information available, the most common pollutants in contaminated sites in Latvia are oil products, pesticides and heavy metals, other substances being present only occasionally.

It seems that at least some contaminated (or potentially contaminated) sites in Latvia are including in the register of contaminated sites because of presence of pollutants, not included in the pollutant list of the national legislation regarding contaminated sites.

Although type of land use is a factor, being taken into account in the process of identification and risk assessment for contaminated or potentially contaminated sites, it is not used for establishing EQS limit values in Latvia.

Study of information, available for pilot sites of INSURE Latvian project partners, shows that there can be a different estimations of groundwater flow direction for the same site.

During the field visit of two contaminated sites Latvia, designated as pilot sites for remediation activities by INSURE Latvian project partners, it was found that both of them are located close to residential or agricultural, with already proved or possible (to a certain degree) impact on them. Taking into account that in Latvia there are no EQS limit values depending on type of land use, these examples are good reason to reconsider this approach. As well as reconsider is it safe and cost-effective to achieve the same EQS limit values after remediation in the industrial, agricultural and residential land.

There are cases when EQS limit values for surface or groundwater in the contaminated sites are more stringent than drinking water standards, meaning that water from contaminated site is perfectly safe for drinking, which is absurd situation.

41

Conclusions

EQS limit values in Latvia are firmly established in a national legislation and is legally binding. EQS limit values in Latvia exist in up to 3 types – target, precaution and critical limit value and, for certain pollutants, can be dependant of granulometric composition of soil (or soil texture). There is no wide practice to use foreign EQS limit values for contaminated sites in Latvia, even in the cases, when no national EQS limit values exist for pollutant of the interest.

EQS guideline values for soil are used in Sweden and can be very site-specific. An important part of the derivation of guideline values is the expected land use at the site. Land use determines the likely activities on the site and therefore determines which groups of people that will be exposed to contaminants and to what extent exposure will occur. Land use also affects the degree to which protection of the soil environment is required on the site. The Swedish generic guideline values have been derived for two different types of land use, sensitive land use (KM) and less sensitive land use (MKM). If generic guideline values are not available, it is possible to use guideline values from other countries. EQS guideline values for soil in Sweden are not legally binding. Sweden has limit values for classification and environmental quality standards for surface water where also some values for sediments are included but generic guideline values for contaminated sediments are missing. Sweden also has guideline values for the classification of groundwater and limit values for drinking water.

Various and different approaches exist over the world on how to establish EQS limit and/or guideline values for contaminated sites. A general comment regarding guideline values is the importance of applying the relevant guideline value for a specific site or condition.

Approaches consider or not consider different factors in establishing the EQS limit or guideline values. Such factors are: texture of soil, type of land use, limit or guideline value, precaution or critical value. Type of pollutant of interest, regarding its physical and chemical properties or analytical methods can be factors as well.

Generally, range of EQS limit or guideline values for the same pollutant can be very wide in different countries, even in those countries which are EU member countries. However, in general terms, European countries tend to have more stringent EQS limit and/or guideline values for contaminated sites than countries from another parts of the world.

Not all EQS limit or guideline values for soil are clearly stated to refer to content of pollutant in the dry solid sample. It is possible that this is another reason for EQS limit and guideline values to differ from country to country.

Some foreign EQS limit/guideline values seems to be incredibly tolerant, especially when compared with level of contamination in actual contaminated sites in Latvia, which are classified as contaminated while having considerably lower levels of pollution than EQS limit values in some other countries.

42

EQS limit values for surface water, at least for EU countries, are more harmonized due to Directive 2013/39/EU, issued to establish average annual and maximum allowed concentration EQS limit values for priority substances in surface water.

43

References

1. “Environment Quality Standards for Soil Pollution”, Government of Japan, Ministry of Environment, 1994, https://www.env.go.jp/en/water/soil/sp.html

2. “Generic Criteria for Soils and Groundwaters”, Soil Protection and Contaminated Sites Rehabilitation Policy, Quebec, 1998.

3. Canadian Council of Ministers of the Environment, 1999, http://ceqg-rcqe.ccme.ca/en/index.html

4. “Circular on Target Values and Intervention Values for Soil Remediation”, “Dutch Target and Intervention values”, 2000, http://www.esdat.net/Environmental%20Standards/Dutch/annexS_I2000Dutch%20Environmental%20Standards.pdf

5. National Food Agency in Sweden, regulation SLVFS 2001:30, https://www.livsmedelsverket.se/globalassets/om-oss/lagstiftning/dricksvatten---naturl-mineralv---kallv/slvfs-2001-30-kons-2015-3-webb.pdf

6. Canadian Council of Ministers of the Environment, 2001, http://ceqg-rcqe.ccme.ca/download/en/317

7. Law on Pollution, 2001, https://likumi.lv//ta/id/6075 8. Cabinet of Ministers Regulation No 483 “Procedure of identification and registration of

contaminated and potentially contaminated sites” (issued on 20th November of 2001), http://likumi.lv//ta/id/55895

9. Recatala L., Mico C., Sanchez J., Boluda R. “Approaches for Characterising Contaminated Sites; an Analysis Considering the Role of Soil”, Transactions on Ecology and Environment vol 46, WIT Press, 2001.

10. Swedish Environmental Protection Agency, Methods for inventories of contaminated sites, 2002, http://www.naturvardsverket.se/Documents/publikationer/620-5053-2.pdf?pid=2816

11. Cabinet of Ministers Regulation No 118 “Regulation on the Quality of the Surface Water and Groundwater” (issued on 12th March 2002), http://likumi.lv//ta/id/60829

12. “Guidelines for Remediation on Contaminated Sites”, Environmental Guidelines No 7, Danish Environmental Protection Agency, 2002.

13. Kalniņa D. “Nafta un vides problēmas” (“Oil and environmental problems”), Riga Technical University, Riga, 2005.

14. Cabinet of Ministers Regulation No 804 “Regulation of the Quality Normatives for Soil and Subsoil” (issued on 25th October 2005), http://likumi.lv//ta/id/120072

15. European Union regulation EC 1881/2006, setting maximum levels for certain contaminants in foodstuffs, 2006, http://eur-lex.europa.eu/legal-content/EN/TXT/PDF/?uri=CELEX:32006R1881&from=SV

16. Cabinet of Ministers Regulation No 305 “Regulation on the Cadastral Valuation” (issued on 18th April 2006), http://likumi.lv//ta/id/134568

17. “Vēsturiski piesārņotu vietu sanācija” (“Remediation of Historical Contaminated Sites”), draft National program for European Regional Development Fund application, 2006, http://www.vidm.gov.lv/lat/finansu_instrumenti/kohez/files/text/finansu_instrumenti/koh_f/nac_prog_2007_2013//NP_piesarnojums.pdf

44

18. State Report “О состоянии окружающей среды в городе Москве в 2008 году” (“About State of Environment in the Moscow City in the 2008”), State Institution of Nature Protection “Mosecomonitoring”, http://www.mosecom.ru/reports/

19. Swedish Environmental Protection Agency, Guideline values for contaminated land, report 5976, 2009, http://www.naturvardsverket.se/Documents/publikationer/978-91-620-5976-7.pdf?pid=3574

20. Shayler H., McBride M., Harrison E. “Sources and Impacts of Contaminants in the Soil”, Cornell Waste Managemant Institue, Ithaca, 2009.

21. SPI, Remediation of contaminated gas stations and diesel plants, 2010, http://spbi.se/spimfab/files/2013/02/SPBI-rek_ebh-fororenade-bensinst-dieselanl_uppdaterad20120129.pdf

22. Wuana R.A., Okieimen F.E. “Heavy Metals in Contaminated Soils: a Review of Sources, Chemistry, Risks and Best Available Strategies for Remediation”, ISRN Ecology, 2011.

23. “2007 – 2013. gada finanšu plānošanas perioda ierobežotas atlases 3.4.1.4. aktivitātes „Vēsturiski piesārņoto vietu sanācija” projektu saraksta papildināšanas iespēju izvērtēšana, veicot piesārņoto un potenciāli piesārņoto vietu reģistrā iekļauto vietu izvērtēšanu atbilstoši piesārņojumu pakāpei un nosakot to atbilstību vēsturiski piesārņotās vietas statusam” (”Evaluation of possibility to expand the list of project list for limited selection of activity No 3.4.1.4 “Remediation of Historically Contaminated Sites” for financial planning period for years 2007 – 2013, by evaluating sites, included in the PPPV register accordingly to their grade of contamination and identifying their accordance to the status of historically contaminated site”), Reserach ordered by Latvian Ministry of Environment Protection and Regional Development, 2012.

24. “Draft National Norms and Standards for the Remediation of Contaminated Land and Soil Quality”, Department of Environmental Affairs, “Government Gazette”, Republic of South Africa, Vol 561, Pretoria, 2012.

25. Rijkswaterstaat Environment, Soil Remediation Cirkular, 2013, http://rwsenvironment.eu/publish/pages/97218/soil_remediation_circular_2013_july_2013.pdf

26. Geological Survey of Sweden, Groundwater Quality Criteria, report SGU 2013:01, 2013. http://resource.sgu.se/produkter/sgurapp/s1301-rapport.pdf

27. Directive 2013/39/EU “Amending Directives 2000/60/EC and 2008/105/EC as regards priority substances in the field of water policy” (issued 12th August 2013), http://eur-lex.europa.eu/LexUriServ/LexUriServ.do?uri=OJ:L:2013:226:0001:0017:EN:PDF

28. Cabinet of Ministers Regulation No 240 “General Regulation on the Planning, Use and Construction in the Territory” (issued 30th April 2013), http://likumi.lv//ta/id/256866

29. Кулдунбаев Н.К., Фогт Р.Б., Арнолдуссен А., Сыдыкбаев Т.Н., Окланд Т.И., Эйлертсен О. “Содержание тяжелых металлов в почве национального парка «Беш-Таш»” (“Content of the Heavy Metals in the Soil of the National Park “Besh-Tash”), Вестник КАЗНМУ, 2013.

30. “Environment Quality Standards for Contaminated Sites”, Rationale and Guidance Document, Nova Scotia Environment, 2014.

31. Swedish Agency for Sea and Water Management, regulation HVMFS 2015:4, https://www.havochvatten.se/download/18.39e6d68414ca353051f2d15d/1429085661024/HVMFS+2015-4-ev.pdf

45

32. Swedish Environmental Protection Agency, Calculation program, version 2.0.1, 2016, http://www.naturvardsverket.se/upload/stod-i-miljoarbetet/vagledning/fororenade-omraden/Version2-0-1-nv-berakningsprogram-rv-mark20160706.xlsm

33. Ministry of Infrastructure and Environment, website 2016-11-30, http://rwsenvironment.eu/subjects/soil/legislation-and/soil-remediation/

34. Geological Survey of Sweden, regulation SGU FS 2016:1, http://resource.sgu.se/dokument/om-sgu/foreskrifter/sgu-fs-2016-1.pdf

35. Norwegian Environmental Agency, Grenseverdier for klassifisering av vann, sediment og biota, Miljödirektoratet, M- 608, 2016, http://www.miljodirektoratet.no/Documents/publikasjoner/M608/M608.pdf

36. Texas Risk Reduction Program Protective Concentration Levels”, Texas Commission on Environmental Quality, Tier 1 PCL and supporting tables, 2016, https://www.tceq.texas.gov/remediation/trrp/trrppcls.html

37. “Ar naftas produktiem potenciāli piesārņotas mazuta saimniecības teritorijas izpētes stratēģijas izstrāde, ietverot teritorijas topogrāfisku uzmērīšanu” (“Development of Investigation Strategy, Including Topographic Survey, for Territory of Black Fuel Storage Facility, Potentially Contaminated with Oil Products”), SIA “Vides Konsultāciju Birojs”, 2016.

38. “Projekta INSURE pilotvietu izpētes stratēģija Vidzemes plānošanas reģiona teritorijā” (“INSURE project pilot sites investigation strategy in the territory of Vidzeme planning region”), Vidzeme planning region, 2016.

39. “Piesārņoto un potenciāli piesārņoto vietu informācijas sistēma” (Latvian Information System of Contaminated and Potentially Contaminated Sites), http://oas.vdc.lv:7779/lva/ppv_read_pub/

40. LAMO Hydrogeological Model, Riga Technical University. 41. www.balticmaps.eu 42. www.maps.google.lv

Appendix 1. Guideline and limit values

1

Table 1. Swedish Environmental Protection Agency generic guideline values for soil, 2009. Parameter Unit Sensitive

land use (KM)

Less sensitive land use (MKM)

Comment

Antimony mg/kg dry weight (dw)

12 30

Arsenic mg/kg dw 10 25

Barium mg/kg dw 200 300

Cadmium mg/kg dw 0,8 12 Revised June 2016

Chromium (VI) mg/kg dw 2 10 Note 2

Chromium total mg/kg dw 80 150 If the percentage of chromium (VI) is greater than 1% of the total amount of chromium, chromium (VI) should also be assessed for risk.

Cobalt mg/kg dw 15 35

Copper mg/kg dw 80 200

Lead mg/kg dw 50 400

Mercury mg/kg dw 0,25 2,5

Molybdenum mg/kg dw 40 100

Nickel mg/kg dw 40 120

Vanadium mg/kg dw 100 200

Zinc mg/kg dw 250 500

Cyanide (total) mg/kg dw 30 120

Cyanide (free) mg/kg dw 0,4 1,5 Note 2

Total phenol and cresols mg/kg dw 1,5 5 Note 2

Sum of chlorophenols (monopenta) mg/kg dw 0,5 3 Note 2

Sum of mono- and dichlorobenzenes mg/kg dw 5 15 Note 1,2

Trichlorobenzene mg/kg dw 1 10

Total tetra- and pentachloro-benzenes mg/kg dw 0,5 2

Hexachlorobenzene mg/kg dw 0,035 2

Dichloromethane mg/kg dw 0,08 0,25 Note 1,2

Dibromochloromethane mg/kg dw 0,5 2 Note 1,2

Bromodichloromethane mg/kg dw 0,06 1 Note 1,2

Trichloromethane mg/kg dw 0,4 1,2 Note 1,2

Carbontetrachloride (Tetrachloromethane)

mg/kg dw 0,08 0,35 Note 1,2

1.2-dichloroethane mg/kg dw 0,02 0,06 Note 1,2

1.2-dibromoethane mg/kg dw 0,0015 0,025 Note 1,2

1,1,1-trichloroethane mg/kg dw 5 30 Note 1,2

Trichlorethane (Tri) mg/kg dw 0,2 0,6 Note 1,2

Tetrachloroethene (Per) mg/kg dw 0,4 1,2 Note 1,2

Dinitrotoluen (2,4) mg/kg dw 0,05 0,5 Note 2

PCB-7 mg/kg dw 0,008 0,2 PCB-7 are assumed to be 20% of PCBs-tot

Dioxin (TCDD-ekv WHO-TEQ) mg/kg dw 0,00002 0,0002 Also include dioxin-like PCBS

PAH-L mg/kg dw 3 15 PAH with low molecular weight

Appendix 1. Guideline and limit values

2

PAH-M mg/kg dw 3,5 20 PAH with medium-high molecular weight. Revised June 2016.

PAH-H mg/kg dw 1 10 PAH with high molecular weight

Benzene mg/kg dw 0,012 0,04 Note 1,2

Toluene mg/kg dw 10 40 Note 1,2

Ethylbenzene mg/kg dw 10 50 Note 1,2

Xylene mg/kg dw 10 50 Note 1,2

Aliphatic fraction >C5-C8 mg/kg dw 25 150 Note 1,2. Revised June 2016.

Aliphatic fraction >C8-C10 mg/kg dw 25 120 Note 1. Revised June 2016.

Aliphatic fraction >C10-C12 mg/kg dw 100 500 Note 1

Aliphatic fraction >C12-C16 mg/kg dw 100 500

Aliphatic fraction >C5-C16 mg/kg dw 100 500 Sum of the aliphatic fractions above

Aliphatic fraction >C16-C35 mg/kg dw 100 1000

Aromatic fraction >C8-C10 mg/kg dw 10 50

Aromatic fraction >C10-C16 mg/kg dw 3 15

Aromatic fraction >C16-C35 mg/kg dw 10 30

MTBE mg/kg dw 0,2 0,6 Note 1,2

DDT, DDD, DDE mg/kg dw 0,1 1 New, June 2016.

Aldrine-Dieldrine mg/kg dw 0,02 0,18 New, June 2016.

Quintozene-Pentachloroaniline mg/kg dw 0,12 0,4 New, June 2016.

Organotin compounds mg/kg dw 0,25 0,5 New, June 2016.

Tributyltin (TBT) mg/kg dw 0,15 0,3 New, June 2016.

Dibutyltin (DBT) mg/kg dw 1,5 5 New, June 2016.

Monobutyltin (MBT) mg/kg dw 0,25 0,8 New, June 2016.

Irgarol mg/kg dw 0,004 0,015 New, June 2016.

Diuron mg/kg dw 0,025 0,08 New, June 2016.

Note 1. Substances that may be present in soil air. Additional analyses of soil air and indoor air are recommended. Note 2. Substances that may be present in the groundwater. Additional analyses of groundwater are recommended.

Appendix 1. Guideline and limit values

3

Table 2. Dutch soil intervention values (RIVM 2013) Parameter Unit Intervention values Comments

Concentrations in soil are shown for standard soil (10% organic matter and 25% clay)

Cyanide (complex) mg/kg d.w. 50

Cyanide (free) mg/kg d.w. 20

Thiocyanate mg/kg d.w. 20

Phenol mg/kg d.w. 14

Cresols (sum) mg/kg d.w. 13

Monochlorophenols (sum) mg/kg d.w. 5,4

Dichlorophenols (sum) mg/kg d.w. 22

Trichlorophenols (sum) mg/kg d.w. 22

Tetrachlorophenols (sum) mg/kg d.w. 21

Pentachlorophenol mg/kg d.w. 12

Monochlorobenzene mg/kg d.w. 15

Dichlorobenzenes (sum) mg/kg d.w. 19

Trichlorobenzenes (sum) mg/kg d.w. 11

Tetrachlorobenzenes (sum) mg/kg d.w. 2,2

Pentachlorobenzenes mg/kg d.w. 6,7

Hexachlorobenzene mg/kg d.w. 2

Dichloromethane mg/kg d.w. 3,9

Trichloromethane mg/kg d.w. 5,6

Carbon Tetrachloride (Tetrachloromethane) mg/kg d.w. 0,7

1.2-dichloroethane mg/kg d.w. 6,4

1,1,1-trichloroethane mg/kg d.w. 15

Trichlorethane (Tri) mg/kg d.w. 2,5

Tetrachloroethene (Per) mg/kg d.w. 8,8

Monochloroethene (Vinylchloride) mg/kg d.w. 0,1

1,1-dichlororethane mg/kg d.w. 15

1,1-dichlororethene mg/kg d.w. 0,3

1,2-dichloroethene (sum) mg/kg d.w. 1

Dichloropropanes (sum) mg/kg d.w. 2

1,1,2-trichloroethane mg/kg d.w. 10

PCB (sum 7) mg/kg d.w. 1

Dioxin (sum I-TEQ) mg/kg d.w. 0,00018

Monochloroanilines (sum) mg/kg d.w. 50

Chloronaphthalene (sum) mg/kg d.w. 23

PAHs (total (sum 10) mg/kg d.w. 40

Benzene mg/kg d.w. 1,1

Toluene mg/kg d.w. 32

Ethylbenzene mg/kg d.w. 110

Xylenes (sum) mg/kg d.w. 0,2

Styrene (vinylbenzene) mg/kg d.w. 86

Mineral oil mg/kg d.w. 5000

Chlorodane (sum) mg/kg d.w. 4

DDT (sum) mg/kg d.w. 1,7

DDE (sum) mg/kg d.w. 2,3

DDD (sum mg/kg d.w. 34

Aldrin mg/kg d.w. 0,32

Drins (sum) mg/kg d.w. 4

α-endosulphan mg/kg d.w. 4

α-HCH mg/kg d.w. 17

β-HCH mg/kg d.w. 1,6

γ-HCH (lindane) mg/kg d.w. 1,2

Heptachlor mg/kg d.w. 4

Heptachlor epoxide (sum) mg/kg d.w. 4

Organotin compounds (sum mg/kg d.w. 2,5

MCPA mg/kg d.w. 4

Atrazine mg/kg d.w. 0,71

Carbaryl mg/kg d.w. 0,45

Carbofuran mg/kg d.w. 0,017

Asbestos mg/kg d.w. 100

Cyclohexanone mg/kg d.w. 150

Dimethyl phthalate mg/kg d.w. 82

Diethyl phthalate mg/kg d.w. 53

Di-isobutyl phthalate mg/kg d.w. 17

Dibutyl phthalate mg/kg d.w. 36

Butyl benzyl phthalate mg/kg d.w. 48

Dihexyl phthalate mg/kg d.s. 220

Appendix 1. Guideline and limit values

4

Di(2-ethylhexyl)phthalate mg/kg d.w. 60

Pyridine mg/kg d.w. 11

Tetrahydofuran mg/kg d.w. 7

Tetrahydrothiophene mg/kg d.w. 8,8

Tribromomethane (bromoform)

mg/kg d.w. 75

Appendix 1. Guideline and limit values

5

Tabel 3. Limit values to determine chemical classification of surface waters (HVMFS 2015:4).

Limit values to determine chemical classification of surface waters (HVMFS 2015:4)

Blue colour indicate Swedish limit values.

Name of substance Type of substance

CAS number

AA-EQS (annual average)

AA-EQS (annual average)

MAC-EQS (maximum allowable concentration)

MAC-EQS (maximum allowable concentration)

EQS EQS EQS Comment

Inland surface waters: Inland surface waters encompass rivers and lakes and related artificial or heavily modified water bodies.

Other surface waters

Inland surface waters: Inland surface waters encompass rivers and lakes and related artificial or heavily modified water bodies.

Other surface waters

Inland surface waters: Biota: Unless explicitly indicated, the biota EQS refer to fish muscle.

Other surface waters: Biota: Unless explicitly indicated, the biota EQS refer to fish muscle.

Sediment: Swedish EQS

µg/L µg/L µg/L µg/L µg/kg (ww) µg/kg

(ww) µg/kg (dw)

Alachlor priority substance

15972-60-8 0,3 0,3 0,7 0,7

Anthracene priority substance

120-12-7 0,1 0,1 0,1 0,1

24 Sediment-EQS refers to 5 % organic C. Normalisation is needed when sediment organic content deviates from 5 %.

Atrazine priority substance

1912-24-9 0,6 0,6 2 2

Benzene priority substance

71-43-2 10 8 50 50

Brominated diphenylethers

priority substance

32534-81-9 4,9 10-8 2,4 10-9 0,14 0,014 0,0085

For the group of priority substances covered by

Appendix 1. Guideline and limit values

6

brominated diphenylethers (No 5), the EQS should be compared with the sum of the concentrations of congener numbers 28, 47, 99, 100, 153 and 154.

Cadmium and its compounds

priority substance

7440-43-9 ≤ 0,08 (Class 1)

0,2 ≤ 0,45 (Class 1)

≤ 0,45 (Class 1)

2300 EQS refers to

dissolved concentration, i.e. sample filtrated though 0,45 µm-filter. For Cadmium and its compounds (No 6) the EQS values vary depending on the hardness of the water as specified in five class categories (Class 1: <40 mg CaCO3/l, Class 2: 40 to <50 mg CaCO3/l, Class 3: 50 to <100 mg CaCO3/l, Class 4: 100 to <200 mg CaCO3/l and Class 5: ≥200 mg CaCO3/l).

(depending on water hardness classes)

priority substance

0,08 (Class 2)

0,45 (Class 2) 0,45 (Class 2)

0,09 (Class 3)

0,6 (Class 3) 0,6 (Class 3)

0,15 (Class 4)

0,9 (Class 4) 0,9 (Class 4)

0,25 (Class 5)

1,5 (Class 5) 1,5 (Class 5)

Carbon-tetrachloride priority substance

56-23-5 12 12 not applicable not applicable

This substance is not a priority substance but one of the other

Appendix 1. Guideline and limit values

7

pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009.

C10-13 Chloroalkanes priority substance

85535-84-8 0,4 0,4 1,4 1,4 17000

No indicative parameter is provided for this group of substances. The indicative parameter(s) must be defined through the analytical method.

Chlorfenvinphos priority substance

470-90-6 0,1 0,1 0,3 0,3

Chlorpyrifos (Chlorpyrifos-ethyl)

priority substance

2921-88-2 0,03 0,03 0,1 0,1

Cyclodiene pesticides: priority substance

Σ = 0,01 Σ = 0,005 not applicable not applicable

Aldrin priority substance

309-00-2

This substance is not a priority substance but one of the other pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009.

Dieldrin priority substance

60-57-1

This substance is not a priority substance but one of the other pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009.

Appendix 1. Guideline and limit values

8

Endrin priority substance

72-20-8

This substance is not a priority substance but one of the other pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009.

Isodrin priority substance

465-73-6

This substance is not a priority substance but one of the other pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009.

DDT total priority substance

not applicable

0,025 0,025 not applicable not applicable

This substance is not a priority substance but one of the other pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009. DDT total comprises the sum of the isomers 1,1,1 trichloro 2,2 bis (p chlorophenyl) ethane (CAS number 50 29 3; EU number 200 024 3); 1,1,1 trichloro 2 (o chlorophenyl) 2 (p chlorophenyl) ethane (CAS

Appendix 1. Guideline and limit values

9

number 789 02 6; EU Number 212 332 5); 1,1-dichloro 2,2 bis (p chlorophenyl) ethylene (CAS number 72 55 9; EU Number 200 784 6); and 1,1 dichloro 2,2 bis (p chlorophenyl) ethane (CAS number 72 54 8; EU Number 200 783 0).

para-para-DDT priority substance

50-29-3 0,01 0,01 not applicable not applicable

This substance is not a priority substance but one of the other pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009.

1,2-Dichloroethane priority substance

107-06-2 10 10 not applicable not applicable

Dichloromethane priority substance

75-09-2 20 20 not applicable not applicable

Di(2-ethylhexyl)-phthalate (DEHP)

priority substance

117-81-7 1,3 1,3 not applicable not applicable 3000 for crustaceans and cephalopods

Diuron priority substance

330-54-1 0,2 0,2 1,8 1,8

Endosulfan priority substance

115-29-7 0,005 0,0005 0,01 0,004

Fluoranthene priority substance

206-44-0 0,0063 0,0063 0,12 0,12 30 for crustaceans and cephalopods

2000 Sediment-EQS

refers to 5 % organic C. Normalisation is needed when sediment organic content deviates from 5 %.

Hexachloro-benzene priority substance

118-74-1

0,05 0,05 10

Appendix 1. Guideline and limit values

10

Hexachloro-butadiene priority substance

87-68-3

0,6 0,6 55

Hexachloro-cyclohexane priority substance

608-73-1 0,02 0,002 0,04 0,02

Isoproturon priority substance

34123-59-6 0,3 0,3 1 1

Lead and its compounds priority substance

7439-92-1 1,213 1,3 14 14

Inland surface waters 130 000, Other surface waters 120 000

EQS refers to dissolved concentration, i.e. sample filtrated though 0,45 µm-filter. AA-EQS for inland water refers to bioavailable concentrations of the substance.

Mercury and its compounds

priority substance

7439-97-6

0,07 0,07 20

EQS refers to dissolved concentration, i.e. sample filtrated though 0,45 µm-filter.

Naphthalene priority substance

91-20-3 2 2 130 130

Nickel and its compounds priority substance

7440-02-0 413 8,6 34 34

EQS refers to dissolved concentration, i.e. sample filtrated though 0,45 µm-filter. AA-EQS for inland water refers to bioavailable concentrations of the substance.

Nonylphenols (4-Nonylphenol)

priority substance

84852-15-3 0,3 0,3 2 2

Octylphenols ((4-(1,1',3,3'-tetramethylbutyl)-phenol))

priority substance

140-66-9 0,1 0,01 not applicable not applicable

Pentachlorobenzene priority substance

608-93-5 0,007 0,0007 not applicable not applicable 370

Pentachlorophenol priority substance

87-86-5 0,4 0,4 1 1

Appendix 1. Guideline and limit values

11

Polyaromatic hydrocarbons (PAH)

priority substance

not applicable

not applicable

not applicable

not applicable not applicable

For the group of priority substances of polyaromatic hydrocarbons (PAH) (No 28), the biota EQS is based on the toxicity of benzo(a)pyrene, which should be measured as a marker for the other PAHs, and whose concentration should be compared with the EQS. The AA-EQS in water is a corresponding value.

Benzo(a)pyrene priority substance

50-32-8 1,7 10-4 1,7 10-4 0,27 0,027 5 for crustaceans and cephalopods, (10 for molluscs, 2 for fish)

Benzo(b)fluor-anthene priority substance

205-99-2

0,017 0,017

Benzo(k)fluor-anthene priority substance

207-08-9

0,017 0,017

Benzo(g,h,i)-perylene priority substance

191-24-2

8,2 10-3 8,2 10-4

Indeno(1,2,3-cd)-pyrene priority substance

193-39-5

Simazine priority substance

122-34-9 1 1 4 4

Tetrachloro-ethylene priority substance

127-18-4 10 10 not applicable not applicable

This substance is not a priority substance but one of the other pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009.

Appendix 1. Guideline and limit values

12

Trichloro-ethylene priority substance

79-01-6 10 10 not applicable not applicable

This substance is not a priority substance but one of the other pollutants for which the EQS are identical to those laid down in the legislation that applied prior to 13 January 2009.

Tributyltin compounds (Tributhyltin-cation)

priority substance

36643-28-4 0,0002 0,0002 0,0015 0,0015

1,6 Sediment-EQS refers to 5 % organic C. Normalisation is needed when sediment organic content deviates from 5 %.

Trichloro-benzenes priority substance

12002-48-1 0,4 0,4 not applicable not applicable

Trichloro-methane priority substance

67-66-3 2,5 2,5 not applicable not applicable

Trifluralin priority substance

1582-09-8 0,03 0,03 not applicable not applicable

Dicofol priority substance

115-32-2 1,3 10-3 3,2 10-5 not applicable10

not applicable10

33

Perfluorooctane sulfonic acid and its derivatives (PFOS)

priority substance

1763-23-1 6,5 10-4 1,3 10-4 36 7,2 9,1

Quinoxyfen priority substance

124495-18-7

0,15 0,015 2,7 0,54

Dioxins and dioxin-like compounds

priority substance

See footnote 10 in Annex X to Directive 2000/60/EC

Sum of PCDD+PCDF+PCB-DL 0,0065 µg.kg-1 TEQ

PCDD: polychlorinated dibenzo-p-dioxins; PCDF: polychlorinated dibenzofurans; PCB-DL: dioxin-like polychlorinated biphenyls; TEQ: toxic equivalents.

Aclonifen priority substance

74070-46-5 0,12 0,012 0,12 0,012

Appendix 1. Guideline and limit values

13

Bifenox priority substance

42576-02-3 0,012 0,0012 0,04 0,004

Cybutryne priority substance

28159-98-0 0,0025 0,0025 0,016 0,016

Cypermethrin priority substance

52315-07-8 8 10-5 8 10-6 6 10-4 6 10-5

Dichlorvos priority substance

62-73-7 6 10-4 6 10-5 7 10-4 7 10-5

Hexabromocyclododecane (HBCDD)

priority substance

See footnote 12 in Annex X to Directive 2000/60/EC

0,0016 0,0008 0,5 0,05 167

Heptachlor and heptachlor epoxide

priority substance

76-44-8 / 1024-57-3

2 10-7 1 10-8 3 10-4 3 10-5 6,7 10-3

Terbutryn priority substance

886-50-0 0,065 0,0065 0,34 0,034

Ammonia (NH3-N) (4) other pollutant

7664-41-7 1 0,66 6,8 5,7

Ammonia concentration, as ammonia-nitrogen (NH3-N), calculated from the concentration of ammoniumnitrogen (NH4-N), temperature and pH:– Conc NH3-N = fraction NH3-N * halt NH4-N, – Fraction NH3-N = 1/(10^(pKa-pH)+1), – pKa = 0,0901821 + 2729,92 / T (T = temperature expressed as Kelvin).

Arsenic other pollutant

7440-38-2 0,5 0,55 7,9 1,1

Bentazone other pollutant

25057-89-0 27

4700

Bisphenol A other pollutant

65873 1,6 0,11 2,7

Appendix 1. Guideline and limit values

14

Bronopol other pollutant

52-51-7 0,7 0,3

C14-17 Chloroalkanes, MCCP

other pollutant

85535-85-9 1 0,2

Diflufenican other pollutant

83164-33-4 0,01

Diclofenac other pollutant

15307-86-5 0,1 0,01

Dichlorprop-P other pollutant

15165-67-0 10

17alpha-ethinylestradiol other pollutant

57-63-6 0,000035 0,000007

Glyphosate other pollutant

1071-83-6 100

Chloridazon other pollutant

1698-60-8 10

Copper other pollutant

7440-50-8 0,5 biological available

biological available: 2,6 for Västerhavet, 0,87 for the Baltic Sea (5)

The value in the table (biological available) should be compared to the measured concentration of dissolved copper multiplited with (DOC/2)^0,6136. If site-specific values for DOC is missing, the value 4,3 µg Cu/l should be used for Västerhavet and 1,45 µg Cu/l for the Baltic Sea.

Chrome (total halt) (5) other pollutant

1333-82-0; 7775- 11-3; 10588-01- 9; 7789-09-5; 7778-50-9

3,4 3,4

The value is based on Cr VI.

Appendix 1. Guideline and limit values

15

MCPA other pollutant

94-74-6 1

Mekoprop & Mekoprop- P other pollutant

7085-19-0 & 16484-77-8

20

Metribuzin other pollutant

21087-64-9 0,08

Metsulfuronmetyl other pollutant

74223-64-6 0,02

Nonylphenolethoxylates other pollutant

0,3 NP-TEQ 0,3 NP-TEQ

The total concentration of nonylfenol (NP) and NP-eqvivalents is calculated according to the following formula: total concentration = Σ(Cx * TEF). TEF-värden: NP = 1; NP1EO = 0,5; NP2EO = 0,5; NPnEO (3 >=n<=8) = 0,5; NPnEO (n >= 9) = 0,005; NP1EC = 0,005; NP2EC = 0,005.

Pirimikarb other pollutant

23103-98-2 0,09

Sulfusulfuron other pollutant

141776-32-1

0,05

Triclosan other pollutant

3380-34-5 0,1 0,01

Uran other pollutant

7440-61-1 0,17 0,17 8,6 8,6

Zinc other pollutant

7440-66-6 5,5 biotillgängligt

3,4 for Västerhavet, 1,1 for the Baltic Sea

Appendix 1. Guideline and limit values

16

17beta-estradiol other pollutant

50-28-2 0,0004 0,00008

Sum of nondioxinlike PCBs (28, 52, 101, 138, 153 and 180)

other pollutant

125 75

Appendix 1. Guideline and limit values

17

Table 4. Canadian Sediment Quality Guidelines for the Protection of Aquatic Life for

freshwater (http://st-ts.ccme.ca/en/index.html)

Chemical groups Concentration (μg/kg dry weight) ISQG

Concentration (μg/kg dry weight) PEL

Date

2-Methylnaphthalene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

20.2 201 1998

Acenaphthene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

6.71 88.9 1998

Acenaphthylene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

5.87 128 1998

Anthracene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

46.9 245 1998

Aroclor 1254 PCBs

Organic Polyaromatic compounds Polychlorinated biphenyls

60 340 2001

Arsenic CASRN none

Inorganic Metals

5900 17 000 1998

Benz(a)anthracene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

31.7 385 1998

Benzo(a)pyrene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

31.9 782 1998

Cadmium CASRN 7440439

Inorganic Metals

600 3500 1997

Chlordane Organic Pesticides Organochlorine

4.5 8.87 1998

Chromium (total) CASRN 7440-47-3

Inorganic Metals

37 300 90 000 1998

Chrysene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

57.1 862 1998

Copper Inorganic Metals

35 700 197 000 1998

Dibenz(a,h)anthracene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

6.22 135 1998

Dichloro diphenyl dichloroethane, 2,2-Bis (p-chlorophenyl)-1,1-dichloroethane DDD

Organic Pesticides Organochlorine compounds

3.54 8.51 1998

Appendix 1. Guideline and limit values

18

Chemical name Chemical groups Concentration (μg/kg dry weight) ISQG

Concentration (μg/kg dry weight) PEL

Date

Dichloro diphenyl ethylene, 1,1-Dichloro- 2,2-bis(p-chlorophenyl)-ethene DDE

Organic Pesticides Organochlorine compounds

1.42 6.75 1998

Dichloro diphenyl trichloroethane; 2,2- Bis(p-chlorophenyl)-1,1,1-trichloroethane DDT (total)

Organic Pesticides Organochlorine compounds

1.19 4.77 1998

Dieldrin Organic Pesticides Organochlorine compounds

2.85 6.67 1998

Endrin Organic Pesticides Organochlorine compounds

2.67 62.4 1998

Fluoranthene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

111 2355 1998

Fluorene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

21.2 144 1998

Heptachlor Heptachlor epoxide

Organic Pesticides Organochlorine compounds

0.6 2.74 1998

Hexachlorocyclohexane Lindane

Organic Pesticides Organochlorine compounds

0.94 1.38 1998

Lead Inorganic Metals

35 000 91 300 1998

Mercury CASRN 7439976

Inorganic Metals

170 486 1997

Naphthalene PAHs

Organic Polyaromatic compounds Polycyclic aromatic

34.6 391 1998

Nonylphenol and its ethoxylates CASRN 84852153

Organic Nonylphenol and its ethoxylates

1400 No data 2002

Phenanthrene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

41.9 515 1998

Polychlorinated biphenyls PCBs

Organic Polyaromatic compounds Polychlorinated biphenyls

34.1 277 2001

Polychlorinated dibenzo-pdioxins/ dibenzo furans PCDDs, PCDFs

Organic Polyaromatic compounds Polychlorinated dioxins and furans

0.85 ng TEQ/kg dry weight

21.5 ng TEQ/kg dry weight

2001

Pyrene PAHs

Organic Polyaromatic compounds Polycyclic aromatic hydrocarbons

53 875 1998

Chemical name Chemical groups Concentration (μg/kg dry

Concentration (μg/kg dry

Date

Appendix 1. Guideline and limit values

19

weight) ISQG

weight) PEL

Toxaphene Organic Pesticides Organochlorine compounds

0.1 No PEL derived 2002

Zinc Inorganic Metals

123 000 315 000 1998

Appendix 1. Guideline and limit values

20

Table 5. Swedish Guideline Values and Trend Reversal Starting Point Values for Groundwater (SGU- FS 2016:1)

Parameter Unit Guideline value Trend Reversal Starting Point

Nitrate mg/l 50 20

Nitrite mg/l 0,5 0,1

Phosphate mg/l 0,6 0,1

Pesticides

μg/l 0,1 0,5 total

Detected

Chloride mg/l 100 50; West Coast 75

Conductivity mS/m 150 75

Sulphate mg/l 100 50

Ammonium mg/l 1,5 0,5

Arsenic μg/l 10 5

Cadmium μg/l 5 1

Lead μg/l 10 2

Mercury μg/l 1 0,05

Trichloroethylene + Tetrachloroethylene

μg/l 10 2

Chloroform (Trichloromethane)

μg/l 100 50

1,2- dichloroethane μg/l 3 0,5

Benzene μg/l 1 0,2

Benzo(a)pyrene ng/l 10 2

Sum of 4 PAH:, Benzo(b)fluoranthene Benzo(k)fluoranthene Benzo(ghi)perylene Indeno(1,2,3-cd)pyrene

ng/l 100 20

PFAS (

Appendix 1. Guideline and limit values

21

Table 6. Criteria for Environmental Quality Assessment for Groundwater, Geological Survey of Sweden, 2013:01

Parameter Unit Class 1 Class 2 Class 3 Class 4 Class 5 Comment

Arsenic µg/l <1 1-2 2-5 5-10 ≥10

Lead µg/l <0,5 0,5-1 1-2 2-10 ≥10

Cadmium µg/l <0,1 0,1-0,5 0,5-1 1-5 ≥5

Copper mg/l <0,02 0,02-0,2 0,2-1 1-2 ≥2

Chromium totalt µg/l <0,5 0,5-5 5-10 10-50 ≥50

Mercury µg/l <0,005 0.005-0,01

0,01-0,05 0,05-1 ≥1

Nickel µg/l <0,5 0,5-2 2-10 10-20 ≥20

Zinc mg/l <0,005 0,005-0,01

0,01-0,1 0,1-1 ≥1

Trichloromethane (chloroform)

µg/l <1 1-20 20-50 50-100 ≥100

1.2-dichloroethane µg/l <0,02 0,02-0,1 0,1-0,5 0,5-3 ≥3

Trichlorethane (Tri)

µg/l <0,1 0,1-1 1-2 2-10 ≥10 Sum of trichloroethane and tetrachloroethane

Tetrachloroethene (Per)

Sum PAH4 µg/l <0,001 0,001-0,01

0,01-0,02

0,02-0,1

≥0,1 Sum of benzo(b)flouranthene, benzo(k)flouranthene, benzo(ghi)perylene and indeno(1,2,3-cd)pyrene)

Benzo(a)pyrene µg/l

<0,0005 0,0005-0,001

0,001-0,002

0,002-0,01

≥0,01

Benzene µg/l <0,02 0,02-0,1 0,1-0,2 0,2-1 ≥1

Pesticides (sum) µg/l <0,01 0,01-0,025

0,025-0,05

0,05-0,1

≥0,1/0,5 The value 0,5 µg/l refers to the sum of all measured pesticides (including metabolites)

Appendix 1. Guideline and limit values

22

Table 7. Dutch groundwater target and intervention values, VROM 2000

Parameter Unit

Target values

Intervention values Comment

Shallow (Metals)

Deep (Metals)

Antimony µg/l - 0,15 20

Arsenic µg/l 10 7,2 60

Barium µg/l 50 200 625

Lead µg/l 15 1,7 75

Cadmium µg/l 0,4 0,06 6

Cobalt µg/l 20 0,7 100

Copper µg/l 15 1,3 75

Chromium µg/l 1 2,5 30

Mercury µg/l 0,05 0,01 0,3

Molybdenum µg/l 5 3,6 300

Nickel µg/l 15 2,1 75

Zinc µg/l 65 24 800

Cyanide (complex) µg/l 10 1500

Cyanide (free) µg/l 5 1500

Thiocyanate µg/l - 1500

Phenol µg/l 0,2 2000

Cresols (sum) µg/l 0,2 200

Monochlorophenols (sum) µg/l 0,3 100

Dichlorophenols (sum) µg/l 0,2 30

Trichlorophenols (sum) µg/l 0,03 10

Tetrachlorophenols (sum) µg/l 0,01 10

Pentachlorophenol µg/l 0,04 3

Monochlorobenzene µg/l 7 180

Dichlorobenzenes (sum) µg/l 3 50

Trichlorobenzenes (sum) µg/l 0,01 10

Tetrachlorobenzenes (sum) µg/l 0,01 2,5

Pentachlorobenzenes µg/l 0,03 1

Hexachlorobenzene µg/l 0,00009 0,5

Dichloromethane µg/l 0,01 1000

Trichloromethane (chloroform)

µg/l 6 400

Carbon Tetrachloride (Tetrachloromethane)

µg/l 0,01

1.2-dichloroethane µg/l 7 400

1,1,1-trichloroethane µg/l 0,01 300

Trichlorethane (Tri) µg/l 24 500

Tetrachloroethene (Per) µg/l 0,01 10

Monochloroethene (Vinylchloride)

µg/l 0,01 5

1,1-dichlororethane µg/l 7 900

1,1-dichlororethene µg/l 0,01 10

1,2-dichloroethene (sum) µg/l 0,01 20

Dichloropropanes (sum) µg/l 0,8 80

1,1,2-trichloroethane µg/l 0,01 130

PCB (sum 7) µg/l 0,01 0,01

Dioxin (sum I-TEQ) µg/l - N/A

Monochloroanilines (sum) µg/l - 30

Chloronaphthalene (sum) µg/l - 6

Naphthalene µg/l 0,01 70

Phenanthrene µg/l 0,003 5

Anthracene µg/l 0,0007 5

Parameter Unit Target values Intervention

values Comment

Flouranthene µg/l 0,003 1

Chrysene µg/l 0,003 0,2

Benzo(a)pyrene µg/l 0,0001 0,5

Benzo(a)anthracene µg/l 0,0005

Benzo(k)flouranthene µg/l 0,0004 0,05

Indeno(1,2,3,cd)pyrene µg/l 0,0004 0,05

Benzo(ghi)perylene µg/l 0,0003 0,05

Benzene µg/l 0,2 30

Toluene µg/l 7 1000

Ethylbenzene µg/l 4 150

Appendix 1. Guideline and limit values

23

Xylenes (sum) µg/l 0,2 70

Styrene (vinylbenzene) µg/l 6 300

Mineral oil µg/l 50 600

Chlorodane (sum) µg/l 0,02 ng/l 0,2

DDT/DDE/DDD (sum) µg/l 0,004 ng/l 0,01

Aldrin µg/l 0,009 ng/l -

Dieldrin µg/l 0,1 ng/l -

Endrin µg/l 0,04 ng/l -

Drins (sum) µg/l - 0,1

α-endosulphan µg/l 0,2 ng/l 5

α-HCH µg/l 33 ng/l -

β-HCH µg/l 8 ng/l -

γ-HCH (lindane) µg/l 9 ng/l -

HCH-compounds (sum) µg/l 0,05 1 Sum of the HCH-

compounds above.

Heptachlor µg/l 0,005 ng/l 0,3

Heptachlor epoxide (sum) µg/l 0,005 ng/l 3

Organotin compounds (sum µg/l 0,05-16 ng/l 0,7

MCPA µg/l 0,02 50 (chlorophenoxy-

acetic acid herbicides)

Atrazine µg/l 29 ng/l 150

Carbaryl µg/l 2 ng/l 50

Carbofuran µg/l 9 ng/l 100

Cyclohexanone µg/l 0,5 15000

Phthalates (sum) µg/l 0,5 5

Pyridine µg/l 0,5 30

Tetrahydofuran µg/l 0,5 300

Tetrahydrothiophene µg/l 0,5 5000

Tribromomethane (bromoform)

µg/l - 630

Appendix 1. Guideline and limit values

24

Table 8. Proposed groundwater limit values for remediation of contaminated gas stations and diesel plants, SPI 2010.

Parameter Unit Drinking water Vapors in buildings Irrigation Surface water Wetlands

Lead mg/l 0,005 0,03 0,05 0,5

PAH-L mg/l 0,01 2 0,08 0,12 0,04

PAH-M mg/l 0,002 0,01 0,01 0,005 0,015

PAH-H mg/l 0,00005 0,3 0,006 0,0005 0,003

Benzene mg/l 0,0005 0,05 0,4 0,5 1

Toluene mg/l 0,04 7 0,6 0,5 2

Ethylbenzene mg/l 0,03 6 0,4 0,5 0,7

Xylenes (sum) mg/l 0,25 3 4 0,5 1

Aliphatic fraction >C5-C8 mg/l 0,1 3 1,5 0,3 1,5

Aliphatic fraction >C8-C10 mg/l 0,1 0,1 1,5 0,15 1

Aliphatic fraction >C10-C12 mg/l 0,1 0,025 1,2 0,3 1

Aliphatic fraction >C12-C16 mg/l 0,1 - 1 3 1

Aliphatic fraction >C16-C35 mg/l 0,1 - 1 3 1

Aromatic fraction >C8-C10 mg/l 0,07 0,8 1 0,5 0,15

Aromatic fraction >C10-C16 mg/l 0,01 10 0,1 0,12 0,015

Aromatic fraction >C16-C35 mg/l 0,002 25 0,07 0,005 0,015

MTBE mg/l 0,02 20 0,2 5 15

Appendix 1. Guideline and limit values

25

Table 9. Regulation for Drinking water (SLVFS 2001:30)

Parameter Unit Inexpedient Comment

Antimony µg/l 5

Arsenic µg/l 10

Barium mg/l 1

Lead µg/l 10

Cadmium µg/l 5

Copper mg/l 2 Chromium totalt µg/l 50

Mercury µg/l 1

Nickel µg/l 20

Selenium µg/l 10

Cyanide (complex) µg/l 50

Trichloromethane µg/l 100 Trichlorethane (Tri)

µg/l 10 Sum of trichloroethane and tetrachloroethane Tetrachloroethene (Per)

Monochloroethene (Vinylchloride)

µg/l 0,5

1,2-dichloroethane µg/l 3

Trihalomethanes µg/l 100

Sum of chloroform, bromoform, dibromochloromethane, bromodichloromethane

Pesticides (individual) µg/l 0,1

Regarding aldrin, dieldrin, heptachlor and heptachlor epoxide the limit value is 0,030 µg/l.

Pesticides (sum) µg/l 0,5

Benzene µg/l 1,0

Benzo(a)pyrene) µg/l 0,01

Sum of 4 PAH:, Benzo(b)fluoranthene Benzo(k)fluoranthene Benzo(ghi)perylene Indeno(1,2,3-cd)pyrene

µg/l 0,1

Nitrate mg/l 50

Nitrite mg/l 0,5

Boron mg/l 1

Fluoride mg/l 1,5