engineering s.r.l....7 engineering s.r.l. gomma naturale natural rubber 6231 9245 15050 0 2000 4000...
TRANSCRIPT
engineering s.r.l.
ANTIVIBRANTI CAMPANA COMPONIBILI
MODULAR ANTI-VIBRATION BELL MOUNTS
1
EXAMPLE OF CHOICE OF ANTI-VIBRATION MOUNT:Suppose you need to isolate a 6234 kg refrigeration unit with onefrequency equal to 1800 r.p.m. (30 Hz).
The unit has six resting points with 1.039 kg resting on each point (the load is evenly distributed).
To achieve about 90% insulation, a deflection of about 4 mm. is necessary.
When choosing the anti-vibration mount, check that the maximum recommended load is higher than the load applied.
Please consult the technical guide for correct installation.
Soleco Engineering S.r.l. declines all responsibility in cases where the incorrect installation of the support is detected.
ESEMPIO DI SCELTA DI UN SUPPORTO ANTIVIBRANTE:Si supponga di dover isolare un gruppo frigorifero di 6.234 kg con una frequenza pari a 1800 r.p.m. (30 Hz).
L’unità ha 6 punti di appoggio, su ogni punto d’appoggio gravano 1039 kg (il carico è uniformemente distribuito).
Per ottenere un isolamento del 90% ca. è necessaria una deflessione (freccia) di ca. 4 mm.
Nella scelta del supporto antivibrante controllare che il carico massimo consigliato sia superiore al carico applicato.
Per la corretta installazione consultare l’apposita guida tecnica.
Soleco engineering s.r.l. non si assume responsabilità nei casi dove si evidenzia l’errata installazione del supporto.
1
Il diagramma degli isolamenti, riassume graficamente, le relazioni intercorrenti tra la freccia elastica espressa in mm, il regime vibrante in r.p.m. o i cicli/mm e il grado diisolamento espresso in %.
The insulation diagram shows graphically the ratios between the elastic deflections in mm, the vibration speed in r.p.m. or cycles/mm and the degree of insulation as a %.
NOMOGRAMMANOMOGRAPH
FREQUENZAFREQUENCY
ottimavery good
buonagood
discretafair
sufficientesufficient
zona di risonanzaresonant zone
engineering s.r.l.
Hz
PER SCEGLIERE IL SUPPORTO ANTIVIBRANTE CORRETTO BISOGNA CONOSCERE:1. PESO STATICO della macchina e NUMERO DEI PUNTI DI
APPOGGIO con rispettivo carico gravante.2. FREQUENZA ECCITANTE determinata dal corpo rotante con r.p.m.
più bassa.3. LUOGO D’INSTALLAZIONE: se la macchina viene installata in una
zona sismica, in copertura, se è soggetta alle forze del vento o in una zona con elevata presenza di nebbie saline o altri agenti aggressivi.
4. TEMPERATURA D’IMPIEGO: bisogna tenere in considerazione le temperature alle quali saranno soggetti i supporti antivibranti.
L’INSTALLAZIONE É CORRETTA QUANDO TUTTI I SUPPORTI INSTALLATI PRESENTANO LA STESSA FRECCIA ELASTICA.
Se le basi di appoggio dei diversi supporti antivibranti non sono tra loro a livello, è necessario compensare tale mancanza utilizzando appositi registri (MARTINETTI).
TO CHOOSE THE CORRECT ANTI-VIBRATION MOUNT, YOU MUST KNOW:1. The STATIC WEIGHT of the machine and the NUMBER OF
SUPPORT POINTS with their respective loads;2. The EXCITATION FREQUENCY determined by the rotating body at
the lowest r.p.m..3. INSTALLATION SITE: if the machine is installed in a seismic area,
on the roof, if it is subject to wind forces or in an area with high presence of saline mists or other aggressive agents.
4. WORKING TEMPERATURE: the temperatures to which the anti-vibration mounts will be subject must be taken into
consideration.
THE INSTALLATION IS CORRECT WHEN ALL THE INSTALLED MOUNTS HAVE THE SAME ELASTIC DEFLECTION.
If the support bases of the different anti-vibration mounts are not among them at level, it is necessary to compensate for this lack using special registers (JACKS).
2
engineering s.r.l.
TESTED, CERTIFIED AND PATENTED IN
ITALY AND WORLDWIDE
TESTATI, CERTIFICATI EBREVETTATI IN
ITALIA E NEL MONDO
ANTIVIBRANTE COMPONIBILE.
NESSUNA VULCANIZZAZIONE
FRA GOMMA E METALLO
MODULAR ANTI-VIBRATION
MOUNT. NO VULCANIZATION BETWEEN RUBBER
AND METAL
IDENTIFICAZIONE VISIVA DELLA DUREZZA DEL
CORPO ELASTICO DAL COLORE DEL
CUSCINETTO
SHORE HARDNESSVISUAL
IDENTIFICATION FROM THE COLOUR
OF THE PAD
BUSSOLA ANTISTRAPPO
DI SERIE. NESSUN RISCHIO DI
RIBALTAMENTO
STANDARD ANTI-TEAR
PROTECTION. NO RISK OF OVERTURN
3
engineering s.r.l.
MODELLIDisponibile in 3 grandezze per supportare carichi elevati e dotati di fori asolati per adattarsi alle più comuni misure di fissaggio.
Ogni modello può essere fornito in 3 diverse durezze che vengono identificate dal colore del cuscinetto posto sulla base superiore del supporto.
Il cuscinetto è dotato di rilievi deformabili antiscivolo che consentono all’antivibrante caricato di stazionare per attrito e nel contempo di ridurre la trasmissione di rumori.
MODELSAvailable in 3 sizes to support high loads and equipped with slotted holes to adapt to the most common fixing measures.
Each model can be supplied in 3 different hardnesses which are identified by the color of the bearing placed on the upper base of the support.
The pad has slip-proof, flexible embossing which allow the charged anti-vibration mount to stand by friction and at the same time reduce the transmission of noise.
SERIE CAMPANABELL SERIES
45 ShA 60 ShA 70 ShA
CORPO ELASTICO
ELASTOMERO TERMOPLASTICO ideale per applicazioni in ambienti con temperature di impiego da -45°C a +110°C per i 45 e 70 ShA e da -55°C a +135°C per il 60 ShA. La mescola, in termoplastica reciclabile, presenta una elevata resistenza all’invecchiamento, alle sostanze inquinanti, agli idrocarburi, nebbie saline, raggi UV e detergenti.
ELASTIC BODY
THERMOPLASTIC ELASTOMER ideal for applications with temperatures ranging from -45°C to +110°C for the 45 and 70 ShA version and from -55°C to +135°C for the 60 ShA version. The compound, in recyclable thermoplastic, has a high resistance to ageing, pollutants, hydrocarbons, salt mist, UV rays and detergents.
GOMMA NATURALE indicata per applicazioni in ambienti con temperature comprese fra -25°C e +90°C (disponibile in mescole speciali NBR, HNBR e EPDM).
NATURAL RUBBER suitable for applications in environments with temperatures between -25°C and +90°C (available in special NBR, HNBR and EPDM compounds).
4
BUSSOLA ANTISTRAPPO DI SERIE
NESSUN RISCHIO DI RIBALTAMENTOI supporti a CAMPANA Soleco sono stati testati presso il Politecnico di Milano e hanno soddisfatto in modo eccellente le aspettative assicurando il raggiungimento dei più alti standard qualitativi.
I supporti a CAMPANA Soleco sono protetti da BREVETTO in ITALIA e all’ESTERO.
STANDARD ANTI-TEAR PROTECTION
NO RISK OF OVERTURN Soleco BELL mounts have been tested at the Politecnico di Milano and have successfully met all the requirements, guaranteeing the highest standards of quality.
Soleco BELL mounts are protected by PATENT in ITALY and ABROAD.
CERTIFICATI EBREVETTATI
CERTIFIED ANDPATENTED
engineering s.r.l.
STRUTTURA METALLICA
ACCIAIO INOX AISI 316 adatto per il settore OFFSHORE, alimentare e sanitario.
Inoltre, utilizzato in combinazione con l’elastomero termoplastico, è la soluzione ideale per applicazioni in ambienti con TEMPERATURE ESTREME.
METAL STRUCTURE
AISI 316 STAINLESS STEEL suitable for OFFSHORE, food and health sectors.
In addition, used in combination with thermoplasticelastomer, it is the ideal solution for applications in environments with EXTREME TEMPERATURES.
ACCIAIO ZINCATO UNI EN 10111 DD13 con superficie zincata UNI ISO 2081 Fe/Zn 15c1A bianca.
GALVANIZED STEEL UNI EN 10111 DD13 steel with UNI ISO 2081Fe/Zn 15c1Awhite galvanized coating.
5
engineering s.r.l.
6231
9245
15050
MODELLIMODELS
6
engineering s.r.l.
6231
9245
15050
DIMENSIONALIDIMENSIONS
WEIGHTkg
0.25
0.60
DIMENSIONS C Amm
Bmm
D1mm
D2mm
D3mm
D4mm
Emm
Fmm
Lmm
Hmm
Gmm
6231 67M12
M1034 76.5 90.5 110 9 2
9245M16
M1292 44 98 120 130 50 150 10.5 8.5932.5
15050M20
M16147 56 138 168 12.5 3 1.84
7
engineering s.r.l.GOMMA NATURALENATURAL RUBBER
6231
9245
15050
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
22000
24000
26000
28000
1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR...15050-B limite di impiegolimit of use
carico Max consigliatomax recommended load
X
SCHEDA DI PROVA - TEST DATA SHEET
23/10/2017Pioltello - Italy
Oggetto: supporto antivibrante a CAMPANACFNNR6231.. 45-60-70shA
Data - Date
DA MAGAZZINO - FROM WAREHOUSE
CFNNR6231.. 45-60-70shAValori indicati dalle curve sono conseguenti a prove statiche ricavati con dinamometro marca Acquati modello AG/10E a temperatura +22÷25°C
Provenienza materiale :
Form nr. 7015Object : Bell anti-vibration mount
Dinamometro / Dynamometer matr. MCH009OPERATORE / OPERATOR : Taras ServatyakN° REGISTRO PROVE / TEST REGISTER NUMBER : 173-174-175/17GM
Tolleranze di precisione sulle curve di carico / cedimento ± 0,5% - Accuracy tolerances on load/deflection curves ± 0.5%
Material origin:
Dimensioni - Dimension
Frequenza naturale / Natural frequency : Tolleranza durezza elastomero ± 5 shA / Elastomer hardness tolerance ± 5 shA
The values indicated by the curves are the result of static tests obtained with Acquati AG/10E dynamometer at +22÷25 °C
Curva ottenuta dopo la prova di n° 3 campioni - Curve obtained after 3 tests
Materiali utilizzati / Adopted material
DA FORNITORE - FROM SUPPLIER ……………………………………………………………………………………….
0500
10001500200025003000350040004500500055006000650070007500800085009000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
Elemento elastico: Gomma Naturale resistente a temperature di esercizio da -20 a +90°C.Corpo metallico: Acciaio UNI EN 10111 DD13 con superficie zincata UNI ISO 2081 Fe/Zn 15c1A bianca. Cuscinetto superiore: Elastomero termoplastico TPV 80shA colorato rispondente all'elemento elastico interno:45shA Beige - 60shA Rosso - 70shA NeroA richiesta: Versione in acciao INOX AISI 316
Elastic body: Natural Rubber resistant to operating temperatures from -20 to +90°C.Metallic body: Zinc UNI ISO 2081 Fe/Zn 15c1Awhite Steel UNI EN 10111 DD13. Upper pad: Thermoplastic elastomer TPV 80shA, coloured depending on the hardness of the inner elastic body:45shA Beige - 60shA Red - 70shA BlackOn request: AISI 316 stainless steel version
CFNNR6231.. - Gomma Naturale / Natural Rubber
8 - 13 Hz
limite di impiegtousage limit
45 ShA
70 ShA
60 ShA
90008500800075007000650060005500500045004000350030002500200015001000
5000
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of use
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of uselimite di impiego
usage limit
carico max consigliatomax recommended load
45 ShA
70 ShA
60 ShA
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
22000
24000
26000
28000
1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR...15050-B limite di impiegolimit of use
carico Max consigliatomax recommended load
X23/10/2017Pioltello - Italy
Oggetto: supporto antivibrante a CAMPANACFNNR9245.. 45-60-70shA
Data - Date
DA MAGAZZINO - FROM WAREHOUSE
CFNNR9245.. 45-60-70shAObject : Bell anti-vibration mount Form nr. 7015
Dinamometro / Dynamometer matr. MCH009OPERATORE / OPERATOR : Taras ServatyakN° REGISTRO PROVE / TEST REGISTER NUMBER : 177-178-179/17GM
Tolleranze di precisione sulle curve di carico / cedimento ± 0,5% - Accuracy tolerances on load/deflection curves ± 0.5%
Material origin:
Dimensioni - Dimension
DA FORNITORE - FROM SUPPLIER ……………………………………………………………………………………….
Frequenza naturale / Natural frequency : Tolleranza durezza elastomero ± 5 shA / Elastomer hardness tolerance ± 5 shA
SCHEDA DI PROVA - TEST DATA SHEET
Valori indicati dalle curve sono conseguenti a prove statiche ricavati con dinamometro marca Acquati modello AG/10E a temperatura +22÷25°CThe values indicated by the curves are the result of static tests obtained with Acquati AG/10E dynamometer at +22÷25 °C
Curva ottenuta dopo la prova di n° 3 campioni - Curve obtained after 3 tests
Materiali utilizzati / Adopted material
Provenienza materiale :
0
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
Elemento elastico: Gomma Naturale resistente a temperature di esercizio da -20 a +90°C.Corpo metallico: Acciaio UNI EN 10111 DD13 con superficie zincata UNI ISO 2081 Fe/Zn 15c1A bianca. Cuscinetto superiore: Elastomero termoplastico TPV 80shA colorato rispondente all'elemento elastico interno.45shA Beige - 60shA Rosso - 70shA NeroA richiesta: Versione in acciao INOX AISI 316
Elastic body: Natural Rubber resistant to operating temperatures from -20 to +90°C.Metallic body: Zinc UNI ISO 2081 Fe/Zn 15c1Awhite Steel UNI EN 10111 DD13. Upper pad: Thermoplastic elastomer TPV 80shA, coloured depending on the hardness of the inner elastic body.45shA Beige - 60shA Red - 70shA BlackOn request: AISI 316 stainless steel version
CFNNR9245.. - Gomma Naturale / Natural Rubber
7 - 14 Hz
limite di impiegousage limit
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
0
1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of use
carico max consigliatomax recommended load
X
Tolleranza durezza elastomero ± 5 shA / Elastomer hardness tolerance ± 5 shA
SCHEDA DI PROVA - TEST DATA SHEET
Valori indicati dalle curve sono conseguenti a prove statiche ricavati con dinamometro marca Acquati modello AG/10E a temperatura +22÷25°CThe values indicated by the curves are the result of static tests obtained with Acquati AG/10E dynamometer at +22÷25 °C
Curva ottenuta dopo la prova di n° 3 campioni - Curve obtained after 3 tests
Materiali utilizzati / Adopted material
Provenienza materiale :
Form nr. 7015
Dinamometro / Dynamometer matr. MCH009OPERATORE / OPERATOR : Taras ServatyakN° REGISTRO PROVE / TEST REGISTER NUMBER : 180-181-182/17GM
Tolleranza lettura cella di carico da 100 kN ± 0,5% - 100 kN load cell accuracy ± 0.5%
Material origin:
Dimensioni - Dimension
DA FORNITORE - FROM SUPPLIER ……………………………………………………………………………………….
Frequenza naturale / Natural frequency :
23/10/2017Pioltello - Italy
Oggetto: supporto antivibrante a CAMPANACFNNR15050.. 45-60-70shA
Data - Date
DA MAGAZZINO - FROM WAREHOUSE
CFNNR15050.. 45-60-70shAObject : Bell anti-vibration mount
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
22000
24000
26000
1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 7,5 8,0
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
Elemento elastico: Gomma Naturale resistente a temperature di esercizio da -20 a +90°C.Corpo metallico: Acciaio UNI EN 10111 DD13 con superficie zincata UNI ISO 2081 Fe/Zn 15c1A bianca. Cuscinetto superiore: Elastomero termoplastico TPV 80shA colorato rispondente all'elemento elastico interno:45shA Beige - 60shA Rosso - 70shA NeroA richiesta: Versione in acciao INOX AISI 316
Elastic body: Natural Rubber resistant to operating temperatures from -20 to +90°C.Metallic body: Zinc UNI ISO 2081 Fe/Zn 15c1Awhite Steel UNI EN 10111 DD13. Upper pad: Thermoplastic elastomer TPV 80shA, coloured depending on the hardness of the inner elastic body:45shA Beige - 60shA Red - 70shA BlackOn request: AISI 316 stainless steel version
CFNNR15050.. - Gomma Naturale / Natural Rubber
6 - 12 Hz
limite di impiegousage limit
2,01,0 2,51,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 7,5 8,00
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
22000
24000
26000
28000
1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR...15050-B limite di impiegolimit of use
carico Max consigliatomax recommended load
45 ShA
70 ShA
60 ShA
20000
12000
18000
10000
16000
8000
4000
14000
6000
0
2000
22000
24000
26000
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of use
carico max consigliatomax recommended load
8
engineering s.r.l.ELASTOMERO TERMOPLASTICOTHERMOPLASTIC
ELASTOMER
6231
9245
15050
45 ShA
70 ShA
60 ShA
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of use
X
Dinamometro / Dynamometer matr. MCH009OPERATORE / OPERATOR : Taras ServatyakN° REGISTRO PROVE / TEST REGISTER NUMBER : 247-248-249/16GM
Object: Bell anti-vibration mount
25/10/2016
Material origin:
Curva ottenuta dopo la prova di n° 3 campioni - Curve obtained after 3 tests
Materiali utilizzati / Adopted material
Di
mensioni - Di
mension
Tolleranze di precisione sulle curve di carico / cedimento ± 0,5% - Accuracy tolerances on load/deflection curves ± 0.5%
Pioltello - Italy DA MAGAZZINO - FROM WAREHOUSEProvenienza materiale :
DA FORNITORE - FROM SUPPLIER ……………………………………………………………………………………….
SCHEDA DI PROVA - TEST DATA SHEET
Valori indicati dalle curve sono conseguenti a prove statiche ricavati con dinamometro marca Acquati modello AG/10E a temperatura +22÷25°CThe values indicated by the curves are the result of static tests obtained with Acquati AG/10E dynamometer at +22÷25 °C
CFN623110/12E 45-60-70shAForm nr. 7015
Data - Date
Oggetto: supporto antivibrante a CAMPANACFN623110/12E 45-60-70shA
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFN623110/12E - ENFLEX
70shA
60shA
45shA
Elemento elastico: Elstomero temoplastico con caratteristiche elastico-meccaniche costanti nel tempo, elevata resistenza meccanica Elevata resistenza all’invecchiamento atmosferico, all’ozono ed agli U.V. La temperatura di esercizio può variare dai –40°C ai +120°C.Cuscinetto superiore: Elastomero termoplastico TPV 80shA colorato rispondente all'elemento elastico interno.45shA Beige - 60shA Rosso - 70shA NeroCorpo metallico: Acciaio UNI EN 10111 DD13 con superficie zincata UNI ISO 2081 Fe/Zn 15c1A bianca. A richiesta: Versione in acciao INOX AISI 316
Elastic body: Termopastic elastomer which has physical-mechanical characteristics that remain unchanged with time and is highly resistant to atmospheric agents, ozone, organic greaseswhich, salty fog, detergents, UV rays, low and high temperatures from –40°C to +120°C.Upper pad: Thermoplastic elastomer TPV 80shA, coloured depending on the hardness of the inner elastic body.45shA Beige - 60shA Red - 70shA BlackMetallic body: Zinc UNI ISO 2081 Fe/Zn 15c1Awhite Steel UNI EN 10111 DD13.
limite di impiegousage limit
carico max consigliatomax recommended load
6500
6000
5500
5000
4500
4000
3500
3000
2500
2000
1500
1000
500
00500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of use
1,0 1,2 1,4 1,6 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,21,8 2,0
45 ShA
70 ShA
60 ShA
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of use
X
Dinamometro / Dynamometer matr. MCH009OPERATORE / OPERATOR : Taras ServatyakN° REGISTRO PROVE / TEST REGISTER NUMBER : 249-250-251/16GM
Object: Bell anti-vibration mount
25/10/2016
Material origin:
Curva ottenuta dopo la prova di n° 3 campioni - Curve obtained after 3 tests
Materiali utilizzati / Adopted material
Di
mensioni - Di
mension
Tolleranze di precisione sulle curve di carico / cedimento ± 0,5% - Accuracy tolerances on load/deflection curves ± 0.5%
Pioltello - Italy DA MAGAZZINO - FROM WAREHOUSEProvenienza materiale :
DA FORNITORE - FROM SUPPLIER ……………………………………………………………………………………….
SCHEDA DI PROVA - TEST DATA SHEET
Valori indicati dalle curve sono conseguenti a prove statiche ricavati con dinamometro marca Acquati modello AG/10E a temperatura +22÷25°CThe values indicated by the curves are the result of static tests obtained with Acquati AG/10E dynamometer at +22÷25 °C
CFN924512/16E 45-60-70shAForm nr. 7015
Data - Date
Oggetto: supporto antivibrante a CAMPANACFN924512/16E 45-60-70shA
0
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
11000
1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFN924512/16E - ENFLEX70shA
60shA
45shA
Elemento elastico: Elstomero temoplastico con caratteristiche elastico-meccaniche costanti nel tempo, elevata resistenza meccanica Elevata resistenza all’invecchiamento atmosferico, all’ozono ed agli U.V. La temperatura di esercizio può variare dai –40°C ai +120°C.Cuscinetto superiore: Elastomero termoplastico TPV 80shA colorato rispondente all'elemento elastico interno.45shA Beige - 60shA Rosso - 70shA NeroCorpo metallico: Acciaio UNI EN 10111 DD13 con superficie zincata UNI ISO 2081 Fe/Zn 15c1A bianca. A richiesta: Versione in acciao INOX AISI 316
Elastic body: Termopastic elastomer which has physical-mechanical characteristics that remain unchanged with time and is highly resistant to atmospheric agents, ozone, organic greaseswhich, salty fog, detergents, UV rays, low and high temperatures from –40°C to +120°C.Upper pad: Thermoplastic elastomer TPV 80shA, coloured depending on the hardness of the inner elastic body.45shA Beige - 60shA Red - 70shA BlackMetallic body: Zinc UNI ISO 2081 Fe/Zn 15c1Awhite Steel UNI EN 10111 DD13.
carico max consigliatomax recommended load
limite di impiegousage limit
11000
10000
9000
8000
7000
6000
5000
4000
3000
2000
1000
00
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of use
1,5 2,0 2,5 3,0 4,5 5,0 5,5 6,0 6,5 7,03,5 4,0
45 ShA
70 ShA
60 ShA
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
22000
24000
26000
28000
1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR...15050-B limite di impiegolimit of use
carico Max consigliatomax recommended load
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFNNR 8031
carico max consigliatomax recommended load
limite di impiego limit of use
XProvenienza materiale :
SCHEDA DI PROVA - TEST DATA SHEET
Object: Bell anti-vibration mountCFN1505016/20E 45-60-70shA
Material origin:
Oggetto: supporto antivibrante a CAMPANACFN1505016/20E 45-60-70shA
Curva ottenuta dopo la prova di n° 3 campioni - Curve obtained after 3 tests
25/10/2016Pioltello - Italy DA MAGAZZINO - FROM WAREHOUSE
Form nr. 7015
Data - Date
Dinamometro / Dynamometer matr. MCH009OPERATORE / OPERATOR : Taras ServatyakN° REGISTRO PROVE / TEST REGISTER NUMBER : 251-252-253/16GM
Materiali utilizzati / Adopted material
Valori indicati dalle curve sono conseguenti a prove statiche ricavati con dinamometro marca Acquati modello AG/10E a temperatura +22÷25°CThe values indicated by the curves are the result of static tests obtained with Acquati AG/10E dynamometer at +22÷25 °C
DA FORNITORE - FROM SUPPLIER ……………………………………………………………………………………….
Di
mensioni - Di
mension
Tolleranze di precisione sulle curve di carico / cedimento ± 0,5% - Accuracy tolerances on load/deflection curves ± 0.5%
0
2000
4000
6000
8000
10000
12000
14000
16000
18000
20000
2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 7,5
caric
o st
atic
o / s
tatic
load
[N]
deflessione / deflection [mm]
CFN1505016/20E - ENFLEX Elemento elastico: Elstomero temoplastico con caratteristiche elastico-meccaniche costanti nel tempo, elevata resistenza meccanica Elevata resistenza all’invecchiamento atmosferico, all’ozono ed agli U.V. La temperatura di esercizio può variare dai –40°C ai +120°C.Cuscinetto superiore: Elastomero termoplastico TPV 80shA colorato rispondente all'elemento elastico interno.45shA Beige - 60shA Rosso - 70shA NeroCorpo metallico: Acciaio UNI EN 10111 DD13 con superficie zincata UNI ISO 2081 Fe/Zn 15c1A bianca. A richiesta: Versione in acciao INOX AISI 316
Elastic body: Termopastic elastomer which has physical-mechanical characteristics that remain unchanged with time and is highly resistant to atmospheric agents, ozone, organic greaseswhich, salty fog, detergents, UV rays, low and high temperatures from –40°C to +120°C.Upper pad: Thermoplastic elastomer TPV 80shA, coloured depending on the hardness of the inner elastic body.45shA Beige - 60shA Red - 70shA BlackMetallic body: Zinc UNI ISO 2081 Fe/Zn 15c1Awhite Steel UNI EN 10111 DD13.
carico max consigliatomax recommended load
limite di impiegousage limit
20000
18000
16000
14000
12000
10000
8000
6000
4000
2000
02,0 2,5 3,0 4,5 5,0 5,5 6,0 6,5 7,0 7,53,5 4,0
9
engineering s.r.l.CODICI PRODOTTOPRODUCT CODES
CODICE / CODE STRUTTURA METALLICA / METAL STRUCTURE CORPO ELASTICO / ELASTIC BODY
CFNRNR6231 ACCIAIO ZINCATO / GALVANIZED STEEL GOMMA NATURALE / NATURAL RUBBER
CFNRNRX6231 ACCIAIO INOX AISI 316 / AISI 136 STAINLESS STEEL
ELASTOMERO TERMOPLASTICO / THERMOPLASTIC ELASTOMER
ELASTOMERO TERMOPLASTICO / THERMOPLASTIC ELASTOMER
CFNEX6231 ACCIAIO INOX AISI 316 / AISI 136 STAINLESS STEEL
CFNE6231 ACCIAIO ZINCATO / GALVANIZED STEEL
6231
9245
CODICE / CODE STRUTTURA METALLICA / METAL STRUCTURE CORPO ELASTICO / ELASTIC BODY
CFNARNR15050 ACCIAIO ZINCATO / GALVANIZED STEEL GOMMA NATURALE / NATURAL RUBBER
GOMMA NATURALE / NATURAL RUBBERCFNARNRX15050 ACCIAIO INOX AISI 316 / AISI 136 STAINLESS STEEL
ELASTOMERO TERMOPLASTICO / THERMOPLASTIC ELASTOMER
ELASTOMERO TERMOPLASTICO / THERMOPLASTIC ELASTOMER
CFNAEX15050 ACCIAIO INOX AISI 316 / AISI 136 STAINLESS STEEL
CFNAE15050 ACCIAIO ZINCATO / GALVANIZED STEEL
15050
CODICE / CODE STRUTTURA METALLICA / METAL STRUCTURE CORPO ELASTICO / ELASTIC BODY
CFNRNR9245 ACCIAIO ZINCATO / GALVANIZED STEEL GOMMA NATURALE / NATURAL RUBBER
GOMMA NATURALE / NATURAL RUBBERCFNRNRX9245 ACCIAIO INOX AISI 316 / AISI 136 STAINLESS STEEL
ELASTOMERO TERMOPLASTICO / THERMOPLASTIC ELASTOMER
ELASTOMERO TERMOPLASTICO / THERMOPLASTIC ELASTOMER
CFNEX9245 ACCIAIO INOX AISI 316 / AISI 136 STAINLESS STEEL
CFNE9245 ACCIAIO ZINCATO / GALVANIZED STEEL
GOMMA NATURALE / NATURAL RUBBER
10
engineering s.r.l.A RICHIESTAON REQUEST
VERSIONE CON BUSSOLA FILLETATA ANTISTRAPPOConsente al Cliente di acquistare i componenti e assemblarli successivamente secondo la reale necessità elastica.
Questa versione è disponibile per tutti i modelli della serie, in tutte le combinazioni previste per la versione standard.
VERSION WITH ANTI-TEAR THREADED BUSHINGThe Customer can purchase the components and assemble them later based on actual elastic requirements.
This version is available for all models in the series, in all the combinations provided for the standard version.
MARTINETTO1. grano filettato con sede per chiave a brugola,2. dado basso UNI 5589,3. rondella elastica spaccata UNI 1751,4. disco in acciaio da 4.0 mm per sostenere la macchina,5. dado alto UNI 5587 per registrare il livello della macchina,6. disco in acciaio da 4.0 mm per distribuire il
carico sull’antivibrante.
Disponibile in M10 - M12 - M16 - M20 anche in ACCIAIO INOX AISI 316.
JACK1. threaded set screw with slot for allen key,2. UNI 5589 low hexagon nut,3. UNI 1751 split elastic washer,4. 4.0-mm steel disc to support the machine,5. UNI 5587 high hexagon nut to level the machine,6. 4.0 mm steel disc to distribute the weight on the
anti-vibration mount.
Available in M10 - M12 - M16 - M20 and in AISI 316 STAINLESS STEEL.
engineering s.r.l.
www.solecosrl.com - [email protected] via Masaccio 12, 20096 Pioltello (Mi) - Italy tel +39 02 92 44 311 - fax +39 02 73 96 50 50
cod.fisc. e p.IVA 01349290153 - reg. impr. MI 148283 M.9711244 - R.E.A. MI 835036ITA_ING_REV2