Application Note

04/2012, V1.0 Page 1

Enabling Multi Session on the IFBD-HE07/08 Ethernet Card

Introduction This application note shows how to enable Multi Session on IFBD-HE07/08 ethernet cards. This documentation covers enabling this setting by browser and command prompt, so choose the method most comfortable. Supported Printers: See Chart in Section II Supported Interfaces: Ethernet (IFBD-HE07/08 Card) Table of Contents I. When is Multi Session Needed? …………………………………………………………… Page 1 II. IFBD-HE07/08 Printer Compatibility ……………………………………………………. Page 2 III. Enabling Multi Session by Browser …………………………………………………….. Page 3 IV. Enabling Multi Session by Command Prompt …………………………………….. Page 7

I. When Is Multi Session Needed? Enable Multi Session to ensure compatibility when replacing older Star ethernet printers. The old ethernet interface card IFBD-HE05/06 was set to Muti Session by default. The latest version, IFBD-HE07/08, is set to single session by default. Some application written for the IFBD-HE05/06 model may still require Multi Session to be enabled. Prior to the release of the StarPRNT Intelligence driver version 1.1a, the OPOS Utility required Multi Session. If the OPOS Utility of a version older than StarPRNT 1.1a is in use, it is recommended to switch the printer back to Multi Session to ensure compatibility. Use Single Session (Default) Switch to Multi Session

New installations with IFBD-HE07/08 printers Replacing older IFBD-HE05/06 printers Using StarPRNT OPOS Utility V1.1a and Higher (Optional) Using StarPRNT OPOS Utility Below V1.1a

Application Note

04/2012, V1.0 Page 2

II. IFBD-HE07/08 Printer Compatibility The IFBD-HE07/08 ethernet interfaces are supported by the minimum firmware versions listed in the table below. In addition, the table also lists the minimum Driver/Utility Package necessary to support these interfaces. Confirm the printer has the minimum required firmware or higher by performing a self test. To perform a self test: 1. Power off the printer 2. Press and hold the feed button while turning the printer back on The firmware version will be printed at the top in most cases.

Model Name Compatible Printer Firmware Versions

Compatible Printer Drivers and Utility Versions

StarPRNT Intelligence

Other Printer Drivers

FVP10 Ver. 1.3~ Yes - TSP700II Ver. 3.0~ Yes CD Ver. 1.1

TSP650 Ver. 3.0~ Yes CD Ver. 1.0

TSP800II Ver. 1.2~ Yes - TSP828L Ver. 2.0~ - CD Ver. 3.0

TSP1000 Ver. 3.0~ - Line/Raster Mode

Printer Driver

TUP500 Ver. 3.0~ - CD Ver. 1.0

SP700 Ver. 3.0~ Yes CD Ver. 1.1

SP500 Ver. 4.0~ Yes

Line/Raster Mode

Printer Driver

HSP7000 Ver. 5.0~ - CD Ver. 2.0

If the firmware of the printer is lower than the compatible version listed, contact Star for assistance with upgrading. This chart is current as of April 2012.

Application Note

04/2012, V1.0 Page 3

III. Enabling Multi Session by Browser 1. At this time, the printer should have already been assigned an IP Address. It should be powered on and connected to the same network as the PC. For installation instructions on installing an ethernet printer, visit our Ethernet FAQ section first.

2. Open any web browser and type the printer’s IP Address in the address bar. Then, click “Login” in the left menu bar.

3. Log in. The factory settings for the IFBD-HE07/08 card are: User Name: root Password: public Note: These credentials can be changed in the browser tool after logging in if desired.

Application Note

04/2012, V1.0 Page 4

4. Click “System Configuration”.

5. Set #9100 Multi Session to “Enable”. Then click “Submit”.

Application Note

04/2012, V1.0 Page 5

6. This page confirms the information set. Click “Save” in the left menu bar.

7. Select “Save -> Configuration printing -> Restart device” and then click “Execute”.

Application Note

04/2012, V1.0 Page 6

8. It will take about ten seconds for the printer to restart with the new configuration settings. At this point, close the browser window.

Congratulations! You have successfully enabled Multi Session using a browser.

Application Note

04/2012, V1.0 Page 7

IV. Enabling Multi Session by Command Prompt 1. Open the Command Prompt.

2. Type “telnet” and the printer’s IP Address after.

3. Log in. The factory settings for the IFBD-HE07/08 card are: User Name: root Password: public Note: These credentials can be changed in the menu after logging in if desired.

4. Enter 2 for System Configuration.

Application Note

04/2012, V1.0 Page 8

5. Enter 2 for #9100 Multi Session

6. Enter 1 for Enable.

Application Note

04/2012, V1.0 Page 9

7. Enter 99 for Back to Main Menu.

8. Enter 98 for Save & Restart.

Application Note

04/2012, V1.0 Page 10

9. Enter 1 for Save & Configuration printing & Restart device.

10. The settings are sent directly to the printer. Connection to the host is lost as the printer resets itself automatically. A test print is printed showing all the ethernet card settings and confirming Multi Session has been enabled. 11. Close the Command Prompt.

Application Note

04/2012, V1.0 Page 11

Congratulations! You have successfully enabled Multi Session using the Command Prompt.

Star Micronics Worldwide

Star Micronics Co., Ltd. 536 Nanatsushinya Shimizu-ku, Shizuoka 424-0066 Japan +81-54-347-2163 http://www.star-m.jp/eng/index.htm Star Micronics America, Inc. 1150 King Georges Post Road Edison, NJ 08837 USA 1-800-782-7636 +1-732-623-5500 http://www.starmicronics.com Star Micronics EMEA Star House Peregrine Business Park, Gomm Road High Wycombe, Buckinghamshire HP13 7DL UK +44-(0)-1494-471111 http://www.star-emea.com Star Micronics Southeast Asia Co., Ltd. Room 2902C. 29th Fl. United Center Bldg. 323 Silom Road, Silom Bangrak, Bangkok 10500 Thailand +66-2-631-1161 x 2 http://www.starmicronics.co.th/

Star Micronics is a global leader in the manufacturing of small printers. We apply over 50 years of knowhow and innovation to provide elite printing solutions that are rich in stellar reliability and industry-respected features. Offering a diverse line of Thermal, Hybrid, Mobile, Kiosk and Impact Dot Matrix printers, we are obsessed with exceeding the demands of our valued customers every day. We have a long history of implementations into Retail, Point of Sale, Hospitality, Restaurants and Kitchens, Kiosks and Digital Signage, Gaming and Lottery, ATMs, Ticketing, Labeling, Salons and Spas, Banking and Credit Unions, Medical, Law Enforcement, Payment Processing, and more! High Quality POS Receipts, Interactive Coupons with Triggers, Logo Printing for Branding, Advanced Drivers for Windows, Mac and Linux, Complete SDK Packages, Android, iOS, Blackberry Printing Support, OPOS, JavaPOS, POS for .NET, Eco-Friendly Paper and Power Savings with Reporting Utility, ENERGY STAR, MSR Reading, futurePRNT, StarPRNT… How can Star help you fulfill the needs of your application? Don’t just settle on hardware that won’t work as hard as you do. Demand everything from your printer. Demand a Star!