en1b0041-ie10r0414 cpobalance install
DESCRIPTION
En1b0041-Ie10r0414 CPOBalance InstallTRANSCRIPT
-
5/21/2018 En1b0041-Ie10r0414 CPOBalance Install
1/3
Copyright 2014 Honeywell International Inc EN1B-0041 IE10 R0413
ComfortPoint Open
Balancing Tool
Trademark Information
ComfortPointTMOpen is a trademark of HoneywellInternational Inc.
BACnetis a registered trademark of ASHRAE Inc.
About this guide
This guide describes the software requirements for installingthe Balancing tool.
Purpose
This tool is used to balance and calibrate the CP-VAV andCPO-VAV2A controllers.
Software prerequisites
The Balancing tool can run on Windows 7 Enterprise edition(32-bit or 64-bit) SP1.
The following software are additionally required for installingthe Balancing tool and are supplied on the installation media:
Microsoft .Net Framework 4.5
MSXML 6.0 SP2
Note:
All prerequisite software is automatically installed during thetool installation.
Installing the Balancing tool
The following table informs you when a restart is requiredwhile installing prerequisite software required for theBalancing tool.
To install the Balancing t ool
1 Double-click the :\Disk1\setup.exe from theinstallation media (CD/DVD/Network location).
The Install Shield Wizard window appears indicating thelist of prerequisite software to be installed.
2 Click Install. The Windows Installer 4.5 - XP SP2installation begins as indicated by the progress bar.
The prerequisite software are installed.
Installation Guide
Prerequisite software installation Restart required?
Microsoft .Net Framework 4.5 Restart prompted. Restart
recommended.
MSXML 6.0 SP1 No
Windows Installer 4.5 XP SP2 Restart prompted. Restart
recommended.
-
5/21/2018 En1b0041-Ie10r0414 CPOBalance Install
2/3
INSTALLING THE BALANCING TOOL
EN1B-0041 IE10 R0413 2
3 Click Next.
4 Select the option (as highlighted in the above figure) andclick Next.
5 Enter your User nameand Company Namedetails. TheNextbutton is enabled.
6 Click Next.
7 Click Next.
8 Click Installto initiate the installation.
9 Click Finishto complete the installation.
You can start the tool by either double-clicking theBalancing tool icon from the desktop or go to Start> AllPrograms> Honeywell> ComfortPoint Open Balance.
-
5/21/2018 En1b0041-Ie10r0414 CPOBalance Install
3/3
EN1B-0041 IE10 R0413
April 2014
2014 Honeywell International Sarl
Removing the Balancing tool
This section provides the information for removing theBalancing tool from your computer.
To remove Balancing tool from Control Panel
1 Go to Start> ControlPanel> Uninstall a Program.
2 Select ComfortPoint Openand click Uninstall.
The Balancing tool is removed.
To remove Balancing tool f rom installer
1 Double-click the :\Disk1\setup.exe from theinstallation media (CD/DVD/Network location).
2 Select the Removeoption and click Next.
3 ClickYesto continue the uninstallation.
4 Click Finish.
Troubleshooting tips
This section provides some of the troubleshooting tips.
1. Facing issues while starting the Balancing tool.
Check if the Microsoft .Net Framework 4.5 is installed on
your machine.Install the tool again and launch the tool.
2. Facing communication issues with multiple tools(ComfortPoint Open Balancing tool and ComfortPointOpen Online tool) open.
Use the Pause/Resume button to ensure only one tool isconnected at a time.
Note:
The ComfortPoint Open Online tool and ComfortPoint OpenBalancing tool can coexist on the same machine and you canwork simultaneously on both the tools. However, at any givenpoint in time only one tool can be online and connect tocontrollers.
Honeywell Building Solutions
1985 Douglas Drive North
Golden Valley MN 55422-4386
USA
www.honeywell.com