en short operating instructions
TRANSCRIPT
7/28/2019 En Short Operating Instructions
http://slidepdf.com/reader/full/en-short-operating-instructions 1/4
Brief Instruction TruShear Series 3000
1 SAFETY ............................................................................................................................. 1
2 OPERATING- AND DISPLAY ELEMENTS................................................................... 2
3 BRIEF OPERATING INSTRUCTION OF THE PLATE SHEARS ................................. 3
3.1 SETTINGS, DATA INPUT FOR STARTING WORK ........................................................................ 3 3.2 SWITCH OFF MACHINE ............................................................................................................. 3
4 POSITIONING CONTROL ELGO 85............................................................................... 4
1 Safety
You must first read the Chapter „Safety“ from the Operating Instruction or to be trained accordingly.
Only after that, you are allowed to work on the machine!
7/28/2019 En Short Operating Instructions
http://slidepdf.com/reader/full/en-short-operating-instructions 2/4
BRIEF INSTRUCTION
2 Operating- and Display Elements
Operating- and Display Elements on the front side of the control cabinet with the most
important options
Pos. IdentificationOperating- / Display
ElementComments
0 red – yellow Main switchSwitch On / interrupt power supply
1Key switch
Set up - Auto
Change controlSetup-, Automatic mode
2Signal lamp White
Auto
Automatic modeShear is ready for operation
3Signal lamp Red
Malfunction
- Rear shielding- Hand protection
4Illumination buttonGreen
On
Main motor with pump
5Push button Red
Off Main motor with pump
6Push button Black
Cutting angle largerEnlarge cutting angle up to 4°
7Push button Black
Cutting angle smallerReduce cutting angle to 1°
8
Push button Black
Empty pressureaccumulator
Emptying pressure accumulator
means to lower shear blade
9Push button Black
Fill pressure
accumulator
Filling pressure accumulator means to pump up shear blade
10Selection switch
Lift ( 0 – 1 )
0 – Lifting Off 1 – Lifting On
11Selection switch 1
Delayed to ( 0 - 1 )
0 – Release presser foot in lower dead point (UT)
1 – Release presser foot in upper dead point (OT)
12Illumination buttonGreen 1
Down - Up
Setting – releasing presser foot
PPositioning
ControlP8511
Control of the axis rear-stop
no program execution
PPositioning
Control
P87111
Control of the axis rear-stopand program execution
Issue: 01/2007 Page 2 - 2
1 Option
7/28/2019 En Short Operating Instructions
http://slidepdf.com/reader/full/en-short-operating-instructions 3/4
BRIEF INSTRUCTION
3 Brief Operating Instruction of the Plate Shears
3.1 Settings, Data Input for Starting Work
- Switch on main switch [0] on the control cabinet
- Check function of the safety devices Hand-protection, E-Stop and
light curtain.
- Activate light curtain at the back-side of the control cabinet with
key switch.
- Switch on main motor on the control cabinet with push button
„Hydraulic On“ [4]
- Check pressure in the retraction system on the applicable
manometer at the tank.
- Set key switch „Control“ [1] on the control cabinet to Auto
(Automatic mode).
- Control will be activated automatically in Single-mode.
- Push [Start] button on the control
- Rear stop moves slowly in direction of the shears and
subsequently back to the reference mark of the measurement
system.
- Input command value for rear stop
- Press [Start]
- Rear-stop moves into position
- Push sheet onto stop or insert after marking.
- Close hand-protection
- Release cutting with presser foot
- Sheet is being cut until the presser foot will be released or the
shear plate has finished the complete stroke
- Programming of the control, see Operating Instruction or Control
Manual.
3.2 Switch Off Machine- Move rear stop up to approximately 20 mm towards the front
- Switch off main motor on the control cabinet with push button [5]
„Off“
- Switch off main switch [0] on the control cabinet.
Issue: 01/2007 Page 2 - 3
7/28/2019 En Short Operating Instructions
http://slidepdf.com/reader/full/en-short-operating-instructions 4/4
BRIEF INSTRUCTION
Issue: 01/2007 Page 2 - 4
4 Positioning Control ELGO 85
DemandPosition
ActualPosition
Quantity
Select single positionor Hand operation
Function button
Start Postioning
Stop Positioning
LED 1-2
mm
Hand
Single
P8511
>
ELECTRIC ELGO
8 9
5 6
2 3
7
4
1
C 0 >
F
Start
Stop
Clear Button
Select
Cursor Button
Display Window
Actual Value Display of the actual position of the rear stop at the moment
Command Value Input or display of the desired command position
Number of Pieces- Display:
Window 1. Number of cuts still to be performed
2. Number of chain dimensions of the set command value which are
still to be positioned.
LEDs
Hand illuminates if Hand-mode has been selected
Single illuminates if Single-mode has been selected
1 – 2 Display of which input window has been selected with the cursor
button.
Push Buttons
[Select] Changing between Hand- and Single-mode
[Start] Start of the positioning process or of reference traveling.
Activate reference traveling only at the first time after switching on
the control.
The [Start] button is without function during Hand-mode.
[Stop] Interruption of the positioning process (continue with [Start])
[>] Cursor-button for selecting the windows Command Value and
Number of Pieces.
[F] Input button for machine parameter. The button must be kept activatedfor approximately 3s in order to get to the parameters.
[0] ... [9] Numerical buttons for data input