18350

18350

MINI-USB10Pin

1 2 3

4

Joystick

360°

360°

360°

For other functionsSwitch operating modesTurn on/off

The working mode and function can be identified by the LED status

Joystick

Video Output Cable

5 Read the GoPro SD card and Charge the GoPro

PC

GoPro Mini to Micro port

SD reading switch

GoPro charging switch

ONOFF

OFFON

USB Cable

Read the GoPro SD card and Charge the GoPro without dismount the GoPro

When the gimbal and GoPro are powered on , connect the Analog Monitor to the function port with the Video Output Cable ,to output the video to the Analog Monitor.

G4S 3-Axis handheld gimbal has a mini to micro port, It can connect the GoPro with a micro usb cable. You can read the GoPro SD card and Charge the GoPro without dismount the GoPro, and it works when the gimbal is powered off.The GoPro charging switch and the SD card reading switch works independently, and it works when the gimbal is powered off The default is off.

Rolling

Rolling

Tilting

TiltingPanning

Panning

Function Button（ ON / OFF ）

1/4 Inch Screw Hole

Suitable for GoPro 4/GroPro 3+/GroPro 3EN

If the indicator light flashes red, the Gimbal will not work correctly due to an error.

Attention !

1 Beginner Guide

2 Product Appearance Instructions

4 Video Output

Operation Instructions3

Inversion Mode When in any working mode, press the function button for three times in succession, the Gimbal will enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset the Gimbal back to the original state.

Manual Pulling Locking The pitching can be adjusted 8 seconds after the Gimbal has been started. Within the Heading Follow and Heading Lock Mode the pitching can be adjusted to the desired angle manually, wait in this position up to 0.5 second until the current angle is adjusted.

Reset

Indicator Explanation

LED Status Explain

Blue light flashes three times Full Power

Blue light flashes twice Enough Power

Blue light flashes once Low Power

Blue light keeps flashing No Power

If any comments or suggestions please do not hesitate to e-mail us directly : service@feiyu-tech.com

Remove the power switch cap, insert two 18350 batteries into the handle.

Mount the camera carefully to the mounting bracket and make sure the camera is firmly connected with the MINI-USB 10Pin

Press the clip at both ends of the clip, clip it as above picture.

Power On / Off

Assembly the clipMount the CameraInsert The Batteries

JoystickAdjust the angleof the gimbal with the joystick when the angle is locked.

Function Interface

Indicator

Working Mode Instructions

Camera stays in its current orientation.

Panning Mode Camera is permitted to pan left or right.

Camera is permitted to pan left or Panning and Tilting Mode

Lock Mode

Vertical tilts or rolls are restricted.

right and tilt up and down. Rolls are restricted.

All panning, tilting and rolls are restricted.

FunctionInterface

Analog Monitor( Equipped By Users )

G4S 3-Axis Handheld GimbalFunction Button

( Indicator Light )Version 1.0

Power On: Single tap the function button,the gimbal shall be powered on after 2 seconds.Power Off: Hold down the function button for 3 seconds to turn off the gimbal.

Attention: Turn the gimbal on after ensuring the camera is secure.

Reset the tilting axis of the gimbal to initial orientation and initial mode.

Operation

Double tap

Single tap

LED status Mode / Status

Single flash

Double flashes

Function Explanation

Panning Mode / Lock Mode

Panning and Tilting Mode

Panning mode

Panning and Tilting mode

Lock mode / Initialize the gimbal

Triple tap

Single tap to switch between panning mode and lock mode

Under panning and tilting mode, single tap to switch to lock mode

Always on

Inversion Mode It is possible to switch to other modes under inversion mode, triple tap again to exit inversion mode and reset

Long press for 3 seconds Power off

Quadruple tap

Flash quicklyRolling angle adjustment / Initialization failure / Malfunction

Reset

Tap button for six times Please refer to“Gimbal Horizontal Angle Adjustment”for operations

Single tap again to awake the gimbal, or triple tap to initialize the gimbal

Rolling angle adjustment

Long press for 1 second Standby

Three flashes Standby

Mode

Panning mode

Panning and Tilting mode

Lock mode

Controllable angle of joystick

Tilting angle

Uncontrollable

Tilting and panning angle

Movement of joystick

Up, Down

Uncontrollable

Up, Down, Left, Right

Operating Instructions of Function Button

Indicator status

Joystick Control

Reset the tilting axis of the gimbal to initial orientation and initial mode.In standby model, keep the gimbal in power-up state, the motor stops working, the indicator light flashes for three times, and single tap again to wake the gimbal.

Standby

Other Function

! ( 1 ) Please install the suitable camera first before power on the Gimbal. ( 2 ) Please turn off the power when not in use.

GND

Video

8 Horizontal Angle Adjustment of The Gimbal

Initialize the gimbal

STEP 1

STEP 2

Tap button for six times for roll angle adjustment, the tilt and roll angle restore to the horizontal status. Under the roll angle adjustment state, move the joystick to the left or to the right to adjust the roll angle, single tap again to save the setting and exit after adjusting.

The horizontal angle needs to be adjusted whenever the following situations happen to the gimbal, user can adjust the horizontal angle by gimbal initialization and joystick.

Note: Please adjust in this state7

Type：18350

USB CableUSB ConnectorCharger

Input: DC 5VOutput: DC 4.2V

Rechargeable Battery

Video Output Cable

How to charging

USB Cable

USB Power Adapter

（Not Included）

Remote Control（Optional Item）

Note: The joystick and function button will be disabled after connecting with the remote control.

Wireless remote control

Receiver for wireless remote control

Steps to connect wireless remote control:

Joystick

Wireless Remote Control

USB Cable

Power

FunctionInterface

FunctionInterface

【 Panning Mode 】/ 【Lock Mode】

【 Panning and Tilting Mode 】

Inversion Mode

OFF

ON

Reset (Restore to the boot-up state)

Function Button

Operation

Long press for 0.5 second

Long press for 3 seconds

Keep the gimbal powered on, restart the remote control and connect the receiver of RC to the gimbal, press the remote control function button for 7 times in 5 seconds, if the indicator on the RC flashes 5 times it means the receiver and the transmitter of RC match successfully, then customer can control the gimbal by the RC.

▲ RC needs to be match code whenever the following situations：（1）Connecting properly but still control in fail.（2）Change the receiver or wireless remote control

Match Code

Up Left RightDown

Wired remote control

Install the receiver for wireless remote control: Insert the receiver for wireless remote control into the function port of gimbal .

Open the wireless remote control.

Open the gimbal.

1

2

3

Use the wireless remote control to control the gimbal.4

15 meters in an open environment.

Connect the Micro interface of wireless remote control with 5V charger by USB cable.

Charging

Remote Control Distance

Power on / off

Please install the receiver properly before power on

!

Function Button

Direction ButtonDirection Button

of The Wired Remote Control

Remote Control Operation Instructions

Turn Off The Gimbal and RC

Calibration Using Remote Control

Operation Explanation Remark

Tap Button Six Times

Match Code Mode Match code when connecting properly but still control in fail or change the receiver/wireless remote control.Tap Button Seven Times

Double Tap

Single Tap

Triple Tap

Quadruple Tap

Long Press For 3 Second

StandbyLong Press For 1 Second

Wireless RC

Wireless RC

G4S 3-Axis Handhled Gimbal is a feature-rich camera stabilizer, yet lightweight and portable.It is prohibited for any user to use the gimbal for any illegal purposes. Guilin Feiyu Electronic Technology Co.,Ltd and our associates assume no liability for any accident, injury, death, loss, or other claim related to or resulting from the use of this product. In no event shall Guilin Feiyu Electronic Technology Co.,Ltd and our associates be liable for incidental or consequential damages relating to or resulting from the use of this product or any of its parts. Damage resulting from use, accident, or normal wear and tear is not covered by our warranty. Guilin Feiyu Electronic Technology Co.,Ltd reserves the right to amend this manual and the terms and conditions of this product at any time.

DISCLA IMER AT T E N T I O N

6 Function Interface Instructions

9 Specification

FunctionInterface

USB Cable USB Connector

Attention: Make sure that the connection to the computer is done by the USB connector

Upgrade........

PC

10 Standard And Optional Accessories

Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware then unzip the RAR file. Refer to the connection diagram to connect the gimbal with the computer.Please refer to the manual of update operation to upgrade, otherwise the Gimbal can not work normally.

The heading follow speed can be configurated through parameter setting software. Users can adjust to the desired following speed mode according to the requirements of filming scene. Three modes for optional: “SLOW” mode, “NORMAL” mode , “FAST” mode. Default setting is “NORMAL” mode.

Firmware Upgrade Instruction

Tilt and Level Calibration

Attention : Please make sure that the connection to the computer is done by the USB connector.

Attention : Please make sure that the connection to the computer is done by the USB connector.

Please visit the official website of Feiyu Tech to get related information: www.feiyu-tech.com

260 g (Without Batteries & Camera)

800 mA

3°/S ~ 150°/S

Camera GoPro HERO4/3+/3

Usage Time 3 ~ 5 Hours

2°/S ~ 75°/S

360°

6.0 V ~ 9 V360°

360°

Working Voltage

Overload Current Protection

Vertical Tilting Angle

Rolls Angle

Horizontal Panning Angle

Tilting Increments

Panning Increments Weight

Reset the tilting axis of the gimbal to initial orientatiozn and initial mode

Single tap to switch between panning mode and lock mode

Under panning and tilting mode, single tap to switch to lock mode

It is possible to switch to other modes under inversion mode, triple tap again to exit inversion mode and reset

Please refer to“Gimbal Horizontal Angle Adjustment”for operations

Single tap again to awake the gimbal, or triple tap to initialize the gimbal

Tip：It will be automatically powered off to save battery if there is no operation within three minutes.

Adjusting steps:

( 1 ) After powering the gimbal on, hold down the function button for one second to enter standby mode, and the LED indicator shall flash for three times;( 2 ) Consecutively tap the function button for three times, LED indicator shall be always on, place the gimbal on a flat surface and keep it stationary;( 3 ) When the initialization is completed, the LED indicator will flash for three times. Afterward pick up the gimbal and single tap to awake the gimbal.

Initialize the gimbal

（1）The tilt angle is not leveled with the horizontal surface.（2）The roll angle is not parallel to the horizontal surface.（3）Under lock mode, the panning angle drifts.

When the initialization failed, the LED indicator will flash quickly, repeat step (2) & (3) to reinitialize.After finished the , the rolling angle still not parallel to the horizontal surface, you can use the joystick to adjust the rolling angle according to .

Rolling angle adjustment

STEP 1STEP 2

Please assemble the gimbal in accordance to the diagram provided .Please upgrade the firmware and configuration settings with the provided USB data cable.Please charge the battery with the provided battery charger.Please install the camera securely before powering on the gimbal.When the gimbal is not in use or placed on the table, please ensure it is powered off.