emulation probe np-113f1-da3sys.ndk-m.com/up_file/np-113f1-da1.pdfnp-113f1-da3...
TRANSCRIPT
IN-CIRCUIT EMULATOR
EMULATION PROBE
NP-113F1-DA3
USER'S MANUAL
Naito Densei Machida Mfg. Co., Ltd. March 2002 Second edition
MS-DOS , WindowsTMは、米国マイクロソフト社の商標です。
PC DOS , IBM PC/ATTMは、米国IBM社の商標です。
○本資料の内容は、後日変更する場合があります。
○本製品は外国為替および外国貿易管理法の規定により戦略物資等(または役務)に該当しますので、日本国
外に輸出する場合には、同法に基づき日本国政府の許可が必要です。
○文書による当社の承諾なしに本資料の転載複製を禁じます。
○この製品を使用した事により、第三者の工業所有権等にかかわる問題が発生した場合、当社製品の構造製法
に直接かかわるもの以外につきましては、当社はその責を負いませんのでご了承ください。
MS-DOS , Windows is a trademark of Microsoft Corporation.TM
PC DOS IBM PC/AT is a trademark of IBM Corporation.TM,
○ The information in this document is subject to change without notice.
○ The export of this product from Japan may be prohibited without governmental license. To export or re-export this
product from a country other than Japan may also be prohibited without a license from that country. Please call a
Naito Densei Machida Mfg. sales representative.
○ No part of this document may be copied or reproduced in any form or by any means without the prior written consent
of Naito Densei Machida Mfg. Co., Ltd. Naito Densei Machida Mfg. Co., Ltd. assumes no responsibility for any errors
which may appear in this document.
○ Naito Densei Machida Mfg. Co., Ltd. does not assume any liability for infringement of patents, copyrights or other
intellectual property rights of third parties by or arising from use of a device described herein or any other liability
arising from use of such a device. No license, either express, implied or otherwise, is granted under any patents,
copyrights or other intellectual property rights of Naito Densei Machida Mfg. Co., Ltd. or of others.
はじめにPREFACE
この度は、エミュレーション・プローブ をお買い求めいただきありがとうございます。NP-113F1-DA3Thank you for purchasing the NP-113F1-DA3 emulation probe.
本製品はインサーキット・エミュレータ シリーズを用いて、113ピン・CSPのNEC製シングNDルチップ・マイコンのディバグを行うため開発されたものです。
This product has been developed for use when debugging NEC's 113-pin CSP single-chip microcomputers,using an ND Series in-circuit emulator.
本製品はNEC製 シリーズにも御使用になれます。 シリーズを御使用の際は、 シリーズを シリーズNS NS ND NSに読み替えてください。
This product can be used NEC's NS Series In this case using NS Series read to change ND Series for NS. ,
Series.
このマニュアルを読む前に、 シリーズのマニュアルを読んで、ディバグ・システムの構成と機能をND理解しておいてください。
Before reading this manual, read the manual supplied with the ND Series to become familiar with theconfiguration and functions of the debugging system.
NP-113F1-DA3 の梱包箱の中には次のものが入っています。お確かめください。万一、不足や破損な
どがありましたらご連絡ください。
The NP-113F1-DA3 package contains the following items. Check that none of the items are missing. If anyitem is found to be missing or damaged, contact Naito Densei.
●エミュレーション・プローブ 1本NP-113F1-DA3Emulation probe NP-113F1-DA3 1
●ユーザーズ・マニュアル(このマニュアル) 1冊
User's Manual (this manual) 1
● 113 1110 01 1LSPACK A N● 113 1110 01 1CSSOCKET A N
目 次CONTENTS
第1章 概 説 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 1CHAPTER 1 OUTLINE
1 1 動作環境 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 1.OPERATING ENVIRONMENT
1 2 対象デバイス ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 1.TARGET DEVICE
第2章 接 続 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2CHAPTER 2 CONNECTION
2 1 シリーズとターゲット・システムの接続 ・・・・・・・・・・・・・・・・・ 2. NDCONNECTING THE ND SERIES TO THE TARGET SYSTEM
2 2 電源投入,切断の順序 ・・・・・・・・・・・・・・・・・・・・・・・・・ 4.POWER-ON/OFF SEQUENCES
付 録1 エミュレーション・プローブのピン対応表 ・・・・・・・・・・・・・・・ 5APPENDIX1 CORRESPONDENCE BETWEEN THE PINS OF THE IC AND EMULATION PROBE
付 録2 ソケットの実装図 ・・・・・・・・・・・・・・・・・・・・・・・・・・ 7APPENDIX2 THE MOUNTING FIGURE OF THE SOCKET
付 録3 113 パッケージの端子配置図 ・・・・・・・・・・・・・・・・・・ 8pin CSPAPPENDIX3 THE TERMINAL ARRANGEMENT FIGURE OF THE 113PIN CSP PACKAGE
- 1 -
第1章 概 説CHAPTER 1 OUTLINE
本章では、 の概要について説明します。NP-113F1-DA3This chapter outlines the NP-113F1-DA3.
1.1 動作環境OPERATING ENVIRONMENT
NP-113F1-DA3 NDは、インサーキット・エミュレータ シリーズとターゲット・システムを接続するた
めのエミュレーション・プローブです。具体的な接続方法については第2章 接続を参照してくださ
い。
The NP-113F1-DA3 is an emulation probe, used to connect an ND Series in-circuit emulator to the targetsystem. For details of the connection, see Chapter 2.
図1-1 動作環境
Figure 1-1. Operating Environment
ND シリーズとターゲット・システムとの接続
Connection between the ND Series and target system
ND SeriesNP-113F1-DA3
インサーキット・エミュレータ エミュレーション・プローブ ターゲット・システム
In-circuit emulator Emulation probe Target system
1.2 対象デバイスTARGET DEVICE
NP-113F1-DA3 NDの対象デバイスは、インサーキット・エミュレータ シリーズを用いてディバグを行
える 113ピン・ タイプのNEC製シングルチップ・マイコンです。CSPThe target devices for the NP-113F1-DA3 are NEC's 113-pin CSP single-chip microcomputers which support
debugging with an ND Series in-circuit emulator.
インサーキット・エミュレータ シリーズに添付の「プローブ接続用コネクタ設定表」を参照してくNDださい。
Refer to the "Connector Setting Table for Probe Connection," supplied with the ND Series in-circuit emulator.
- 2 -
第2章 接 続CHAPTER 2 CONNECTION
本章では、 の接続方法,電源投入,切断の順序について説明します。NP-113F1-DA3This chapter describes the connection of the NP-113F1-DA3 and the system power-on/off sequences.
2.1 NDシリーズとターゲット・システムの接続CONNECTING THE ND SERIES TO THE TARGET SYSTEM
接続手順の概要は次のとおりです。
The connection procedure is outlined below.
注 意 1.接続の際には、ピンの逆差しに注意してください。誤って接続すると、 シリーズが破壊NDされる場合があります。
Cautions When connecting the probe, note the orientation of the pins. If the orientation of the pins is1.
reversed, the ND Series may be damaged.2.接続の際には、全ての電源を切ってください。また電源の投入、切断の順序は必ず守っ
てください。順序を間違えますと破損される場合があります。
2.Before attempting to make a connection, turn off the power to both the ND Series and targetsystem. The power must be turned on and off in the correct sequence. Otherwise, the ND Seriesor target system may be damaged.
3.CSSOCKET113A1110NO1 は予めターゲット・システムに半田付けして下さい。
3. 113 1110 1 .Solder CSSOCKET A NO into the target system beforehand
(1) シリーズとエミュレーション・プローブの接続NDConnecting the emulation probe to the ND Series
① シリーズの電源を切る。NDTurn off the power to the ND Series.
② シリーズの筐体上部を外す。NDRemove the top cover of the ND Series.
③ シリーズと を接続する。ND NP-113F1-DA3Connect the NP-113F1-DA3 to the ND Series.
④ シリーズの筐体上部を元に戻す。NDReplace the top cover of the ND Series.
(2)エミュレーション・プローブとターゲット・システムの接続
Connecting the emulation probe to the target system① ターゲット・システムの電源を切る。
Turn off the power to the target system.② 1ピン位置を合わせながら LSPACK113A1110NO1 CSSOCKET113A1110NO1を に実装して下さい。
Mount LSPACK113A1110NO1 on CSSOCKET113A1110NO1 With aligning 1pin.③ 1ピン位置を合わせながら をNP-113F1-DA3 LSPACK113A1110NO1 と接続して下さい。
Mount on LSPACK113A1110NO1 With aligning 1pin.NP-113F1-DA3④ の4隅のガイドピンをドライバーで回し固定して下さい。NP-113F1-DA3
Turn and fix the guide pin of the four corners in the part tip.NP-113F1-DA3(3)電源の投入
Turn on the power in the specified sequence.
- 3 -
次に、各項目の詳細な接続手順を説明します。
Each step is detailed below.
(1) シリーズとエミュレーション・プローブの接続NDConnecting the emulation probe to the ND Series.
① シリーズの電源を切ります。NDTurn off the power to the ND Series.
② シリーズの本体下面のネジ(4箇所)を外して、本体上部を外します。NDRemove the four screws from the bottom of the ND Series, then remove its top cover.
③ シリーズのサブ・エミュレーション・ボードのプローブ接続用コネクタ(CN1~4)とNDNP- F -DA113 1 3の本体接続用コネクタを接続します。
プローブ接続用コネクタの(CN1~4)の接続位置については、対象デバイスによって異なり
ますので別紙「プローブ接続用コネクタ設定表」を参照して、決められたコネクタに接続してく
ださい。
Connect the emulator connector of the NP- F -DA to the probe connector (CN to CN ) on the113 1 3 1 4
sub-emulation board of the ND Series.The location of the probe connector (CN to CN ) varies with the ND Series model or target device1 4 .
Connect the probe to the correct connector by referring to the "Connector Setting Table for ProbeConnection " supplied with the ND Series, .
④ シリーズの本体上部を元に戻し本体下面のネジ(4箇所)を留めます。NDReplace the top cover of the ND Series, then replace and tighten the four screws.
図2-1 シリーズとエミュレーション・プローブの接続NDFigure 2-1. Connecting the Emulation Probe to the ND Series
※ の機種により異なりますので に添付の 及び資料を参照してくださいND NDシリーズ 、 シリーズ マニュアル 。Varies with the ND Series model. Refer to the manual and other documents supplied with the ND Series.
- 4 -
(2)エミュレーション・プローブとターゲット・システムの接続
Connecting the emulation probe to the target system① ターゲット・システムの電源を切ります。
Turn off the power to the target system.② 1ピン位置を合わせながら LSPACK113A1110NO1 CSSOCKET113A1110NO1を に実装して下さい。
Mount LSPACK113A1110NO1 on CSSOCKET113A1110NO1 With aligning 1pin.③ 1ピン位置を合わせながら をNP-113F1-DA3 LSPACK113A1110NO1 と接続して下さい。
Mount on LSPACK113A1110NO1 With aligning 1pin.NP-113F1-DA3④ の4隅のガイドピンをドライバーで回し固定して下さい。NP-113F1-DA3
Turn and fix the guide pin of the four corners in the part tip.NP-113F1-DA3
図2-2 113ピン・CSPエミュレーション・プローブ接続図
Figure 2-2. Connecting the 113-pin CSP Emulation Probe
2.2 電源投入,切断の順序POWER-ON/OFF SEQUENCES
エミュレーション・プローブとターゲット・システムの接続が終了したら、次に電源を投入しま
す。電源の投入、切断の順序は次の通りです。
After connecting the emulation probe to the target system, turn on the power. The power must be turned onand off in the sequences described below.
ND シリーズとターゲット・システムを接続した場合
When the ND Series is connected to the target system
◎電源の投入順序 ◎ Power-on sequence① シリーズの電源を入れます。 ①ND Turn on the power to the ND Series.② ターゲット・システムの電源を入れます。 ② Turn on the power to the target system.
◎電源の切断順序 ◎ Power-off sequence① ターゲット・システムの電源を切ります。 ① Turn off the power to the target system.② シリーズの電源を切ります。 ②ND Turn off the power to the ND Series.
- 5 -
付 録1 エミュレーション・プローブのピン対応表APPENDIX1 CORRESPONDENCE BETWEEN THE PINS OF THE IC AND EMULATION PROBE
表A-1 NP-113F1-DA3のピン対応表(1/2)
ピン番号 エミュレーション・プローブ ピン番号 エミュレーション・プローブ
Pin No. Emulation probe Pin No. Emulation probeA1 - J3 6
B1 117 K3 38
C1 - L3 -
D1 107 A4 76
E1 103 B4 79
F1 93 C4 85
G1 24 D4 108
H1 16 E4 30
J1 - F4 29
K1 33 G4 19
L1 - H4 44
A2 90 J4 52
B2 118 K4 43
C2 114 L4 47
D2 113 A5 66
E2 104 B5 71
F2 94 C5 80
G2 23 D5 75
H2 15 E5 -
J2 5 H5 60
K2 34 J5 57
L2 37 K5 48
A3 - L5 51
B3 89 A6 61
C3 86 B6 64
D3 100 C6 72
E3 99 D6 65
F3 20 H6 55
G3 10 J6 50
H3 9 K6 58
- 6 -
表A-1 NP-113F1-DA3のピン対応表(2/2)
ピン番号 エミュレーション・プローブ ピン番号 エミュレーション・プローブ
Pin No. Emulation probe Pin No. Emulation probeL6 59 H9 22
A7 69 J9 36
B7 74 K9 31
C7 63 L9 -
D7 62 A10 83
H7 45 B10 88
J7 42 C10 115
K7 49 D10 105
L7 56 E10 97
A8 73 F10 28
B8 77 G10 18
C8 70 H10 7
D8 78 J10 8
E8 101 K10 4
F8 91 L10 32
G8 92 A11 -
H8 14 B11 87
J8 35 C11 -
K8 41 D11 106
L8 46 E11 98
A9 - F11 27
B9 84 G11 17
C9 116 H11 13
D9 111 J11 -
E9 112 K11 3
F9 102 L11 -
G9 21
- 7 -
付 録2 ソケットの実装図APPENDIX2 THE MOUNTING FIGURE OF THE SOCKET
ターゲット・システム Ta rg e t sys te m
C S S O C K E T
L S PA C K
C S IC E
プローブ P R O B E
C S -G U ID E
C S -G U ID Eを回す C S -G U ID E is tu rn e d .
プローブとC S IC Eを接続した状態でL S PA C Kへ実装し、C S -G U ID Eで固定する
It is m o u n te d u n d e rth e c o n d itio n th a t p ro b e a n dC S IC E a re c o n n ec te d to L S PA C K ,a n d tix e d w ith C S -G U ID E
- 8 -
付 録3 113 パッケージの端子配置図PIN CSPAPPENDIX3 THE TERMINAL ARRANGEMENT FIGURE OF THE 113PIN CSP PACKAGE
TOP_VIEW
A B C D E F G H J K L
3
2
1
6
5
4
8
7
11
10
9