electric griddle installation & owners … griddle installation & owners manual serial...

AccuTemp Products, Inc. · 8415 North Clinton Park · Fort Wayne, IN 46825 ·800 210-5907 · accutemp.net

MP5004-1605

ELECTRIC GRIDDLE INSTALLATION & OWNERS MANUAL

Serial Number:Model:

Install Date:

Improper installation, alteration, adjustment,service, cleaning or maintenance of this commercial appliance could result in property damage, serious injury or death.

Read and understand the installation, operational, maintenance instructions before installing, servicing, or operating this commercial appliance.

Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 1

Current Revision: Date Prior Revision DateN/A 8/4/05 None NoneInitial Release

Current Revision: Date Prior Revision DateA 8/16//05 N/A 8/4/5Added {ages 26,28-30 and 34-3; Renumbered pages as necessary

Current Revision: Date Prior Revision DateB 10/7/05 A 8/4/5Added paged ii and 24-27; Modified pages iv, 19-27; Renumbered page iv.

Current Revision: Date Prior Revision DateC 10/12/05 B 10/7/05Added page iii; Modified pages iv, 19-27; Renumbered page 4

Current Revision: Date Prior Revision DateD 11/10/05 C 10/12/05Deleted pages ii, iii and 25; Added pages 18,33 and 34; Modified pages 13,14, 25-32 and 35-40

Current Revision: Date Prior Revision DateE 12/29/05 D 10/12/05Added page ii; Modified pages 18, 19, 22-24, 33 and 34

Current Revision: Date Prior Revision DateMP5004-1202 2/14/12 E 12/29/05Numeric Page Numbers all pages; Pages modified for Engineering Changes

Current Revision: Date Prior Revision DateMP5004-1307 7/15/13 1202 2/14/12Added cut sheets pages 8-10; Changed graphic description - Page 14; Added Operation section - pages 22-24; Added Cleaning section- pages 25-26; Added Service & Troubleshooting section - pages 27-29; Added Parts Commercial section - pages 30-34; Added Military/Maritime Parts section - Pages 36-40; Added Schematic section

DOCUMENT HISTORY

Current Revision: Date Prior Revision DateMP5004-1605 5/24/2016 1307 7/15/13 Replaced Installation Checksheet with latest release pages 3-4 Replaced cut sheets pages 8-13; Operation section-page numbers change to 23-25; Cleaning section page numbers change to 26-27; Service & Troubleshooting secti page numbers change to 27-29; Model EGF Service Parts page numbers change to 31-38;Model EGD Service Parts section page numbers change to 39-48;Model EGF Schematics section page numbers change to 49-53; Model EGD Schematics sec-tion page numbers change to 54-57


DESCRIPTION PAGEDocument History 1Table of Contents 2Warranty Registration Instructions 3Startup Form 4-5Safety Warnings 6-8Accu-Steam Model EGF Specifications 9-12Accu-Steam Model EGD Specifications 13-14Accu-Steam Model EGD & EGF Theory of Operation 15Accu-Steam Model EGF Installation Instructions 16-18Accu-Steam Model EGD Installation Instructions 19-23Accu-Steam Model EGD & EGF Operation Instructions 24-26Accu-Steam Model EGD & EGF Cleaning Instructions 27-28Accu-Steam Model EGD & EGF Service & Troubleshooting 29-31Accu-Steam Model EGF Service Parts 32-39Accu-Steam Model EGD Service Parts 40-49Accu-Steam Model EGf Schematics 50-54Accu-Steam Model EGD Schematics 55-58Warranty 59

This manual is for Accu-Steam Griddles Starting with:Model EGD Series S/N 7547 Model EGF Series S/N 7642

This manual is to be used for all Accu-Steam Electric Models including:

Model NSNEGF4403B3602-00 7310-01-525-8008EGF4403B3602-T3 N/AEGF4403B2405-T3 7310-01-525-8934EGF4403B3605-T3 7310-01-525-8947EGF4403B4805-T3 7310-01-525-8948EGF4403B4802-00 7310-01-590-4486EGF4403A4805-T3 N/AEGD4403B3606-00 7310-01-525-8962EGD4403B4806-00 7310-01-525-8955


Before installing this appliance complete the following items:1. Fill in the warranty registration card enclosed in the documentation packet that came with the appliance.2. Complete the startup checklist on page 4 and 5 of this manual.3. Mail, fax or email the warranty registration card and startup form to AccuTemp Products, Inc

If you have any questions please contact our technical service group. They are available 7 days a week from 7:00 am to 7:00 pm EST.

Toll Free 800 480-0415Office 260 469-3040Fax 260 469-3045Email -Service [email protected] [email protected] Site www.accutemp.net


Contact Name:

Yes No

Yes No

Yes No

Yes No Yes No

Yes No

Yes No

15-50P

L16-20P

L16-30P

Store/Location:

Address:

Phone Number: Fax Number:

Check-Off List

Model # Serial #

Name of Service/Installer Company:

Is the correct NEMA Plug and Receptacle being used on the Supply Power Cord?

General :

Is the electrical wall receptacle positioned in a low heat-zone? Note: It is recommended that the wall receptacle be placed as low as State & Local codes allow. Placement in high heat-zones could cause damage to the electrical cord or plug that would not be covered under the product warranty.

Is the griddle level, both side-to-side and front-to-back?

If this is a table-top installation, have the (4) rubber foot tip/boots been installed?

Electrical Connection :

Is the Supply Power Cord being plugged into a wall outlet?

Is the Supply Power Cord being hard-wired, without the plug, to a breaker box?

Is the Supply Power Cord properly connected to GND?

208/240VAC (All Models)

440/480VAC (24" Models)

440/480VAC (36" & 48" Models)

Type of NEMA Plug?

MP5011-1403 Page: 1

Installation/Operational Checklist & Warranty Registration Form

ELECTRIC - ACCU-STEAM™

Failure to accurately complete and provide this Installation/Operational Checklist & Warranty Registration Form to AccuTemp Products, may delay or void future Warranty Service Calls.

** AccuTemp Products, Inc. is not responsible for the installation and/or modifications to the electrical supply source. **

What is the Electrical Breaker Amperage that will interupt the Supply Voltage to the electric griddle? AMPS

City: State: Zip:

Email:

Technician: Phone Number:


Yes No

Single Φ

208VAC 240VAC 440VAC 480VAC

Yes No

Yes No

Yes No

°F

No

Supply Power Electrical Readings :

Does the Supply Electrcial Power match the information on the griddle model number?

Temperature & Operational Verification :

Three Φ

1Φ = WHT BLK 3Φ = RED WHT BLK

Using a 9 square-grid-pattern on the griddle surface, are the surface temperatures consistant (±5°F)?

Using a weighted contact temperature probe with digital thermometer, does the surface temperature (°F) match the normal operating temperature (°F) set on the Thermostat? Note: DO NOT use an infrared or flat-top mercury thermometer . Yes

Does the unit operate properly for 15 minutes after the griddle has reached operating temperature?

I accept and submit this Installation/Operational Checklist & Warranty Registration Form as complete and accurate:

Restaurant/Facility Manager Approval:Signature Printed Name Date:

Page: 2

Phase (Φ)?

Measured Supply Voltage?

Measured Amperage on Each Leg?

AccuTemp Products, Inc Attn: Warranty Administration

8415 North Clinton Park Dr. Fort Wayne, IN 46825

Attn: Warranty Administration 260 469-3045

Attn: Warranty Administration [email protected]

Mail Fax Email

Does the Griddle heat light cycle OFF/ON once the surface temperature has reached the Thermostat setting?

What is the customer's normal operating Thermostat temperature for the Griddle?

MP5011-1403

Note: If the operating temperature is 250°F, then set Thermostat to 300°F and verify surface temperature. If the operating temperature is 400°F, then set Thermostat to 400°F and verify surface temperature does not exceed 396°F on the high side of the temperature drift/cycle.

Installation/Operational Checklist & Warranty Registration Form

ELECTRIC - ACCU-STEAM™


SAFETY WARNINGSSYMBOL DEFINITIONSSymbols are used to attract your attention to possible dangers. They are only effective if the operator uses proper accident prevention measures. Some of the symbols are boxed text, while other maybe just picture icons. Please give this information the respect they deserve for safe operation.

WARNING TEXT BOXESBelow are definitions of the warning text boxes:

WARNINGIndicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTIONIndicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTEAdvises reader of information or instructions vital to the operation or maintenance of the equipment.

DANGERIndicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.


CAUTION, HOT SURFACE

SAFETY WARNINGS CONTINUED

SYMBOL ICONSBelow are the definitions of symbol icons used in this manual;

ALERT - Notifies the reader of a n important message/warning, usually a safety related message.

DANGEROUS VOLTAGE

INFORMATION - Notifies the reader of important information that may or may not be safety related.

EARTH GROUND


Plug commercial appliance into a properly grounded electrical outlet of the correct voltage, size and plug configuration. If they do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet.

To avoid any personal injury or damage to the unit do not pull the commercial appliance by the power cord.

To prevent any injury, discontinue any use if power cord is frayed or worn.

To prevent any injury or damage this commercial appliance must be installed by a qualified electrician.

To avoid any injury, turn the power off, unplug from the power source and allow to cool before performing any maintenance.

To avoid electrical shock or personal injury, do not steam clean or use excessive water on this commercial appliance.

This product has no “user” serviceable parts. To avoid injury or damage to the commercial appliance use only Authorized AccuTemp Service Agents and Genuine Replacement Parts when service is required.

Genuine AccuTemp Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket parts or generic replacements parts do not have the same specifications to operate safely in AccuTemp equipment. It is imperative that to use Genuine AccuTemp Replacement Parts to avoid injury or damage to the commercial appliance.

Always disconnect from power source before cleaning or servicing.

Any infield modification that bypass the built-in safety features will result in personal injury or death.

This commercial appliance must be properly grounded, in accordance with all National, State or local electrical codes.

This commercial appliance has a totally unique design and is constructed unlike any other griddle on the market today. Any modification may permanently damage the griddle.

This commercial appliance must be level for proper operation and to reduce possible damage to this commercial appliance.

This commercial appliance is heavy, for safe handling, the installer should obtain help as needed or employ appropriate material handling equipment to remove the commercial appliance from the skid and move to the final location in the building.

Temperatures in and around the commercial appliance are very hot and can cause severe burns.

To avoid damage to the cooking surface of this commercial appliance do not use abrasive cleaners such as a griddle stone or brick.

To avoid personal injury or damage to the commercial appliance do not use a water jet to clean this commercial appliance.

To avoid damage to the commercial appliance do not leave a chlorine sanitizer in contact with the stainless steel longer than 10 minutes.

To avoid severe burns slowly remove the grease reservoir to avoid spilling the contents. It is recommended to let it cool before removing.

IMPORTANT SAFETY INSTRUCTIONSIMPORTANT: Read the following safety installation to avoid personal injury or death and to avoid damage to the equipment or property

WARNINGS

CAUTIONS


Short Specification

Griddle shall be an Energy Star compliant electric-heated unit, with a hermetically-sealed vacuum chamber that produces steam that heats the 8-gauge stainless steel griddle plate. Efficient steam heat transfer provides 200–400°F (93–204°C) operating temperature range and uniform griddle surface temperatures of ±5°F (±3°C). Griddle fabricated from cold-rolled stainless steel with 4.5” high back splash, sides that taper from 4.5” to 1.7”, a 4” wide by 1” deep full front grease trough and 11⁄2–2 gallon grease drawer. Unit to be UL listed, UL EPH Sanitation Certified (NSF 4) and manufactured in the USA.

Construction Features

• Cold-rolled and annealed stainless steel griddle plate with polished stainless steel body and stand

• 8 gauge griddle plate with 4.5” high rear splash and 4.5 to 1.7” tapered side walls

• 4” wide by 1” deep full front grease trough

• 2” x 4” drop chute to 11⁄2–2 gallon capacity grease drawer inside enclosed compartment

• 4” legs with bullet feet (standard)

Performance Features

• Hermetically-sealed steam chamber heats griddle plate

• 9.6-kW [24”] or 14.25-kW total power, long-life low watt density heating elements mounted inside vacuum chamber and immersed in chemically pure water (Water never needs replacement)

• Steam transfers heat evenly to entire cooking surface with only ±5°F (±3°C) in temperature variation

• Rapid surface temperature recovery [10 seconds or less] allows turning product to same spot

• Smooth cold-rolled stainless steel griddle surface speeds and simplifies cleaning

Standard Control Features

• Power-On switch & indicator light• Heating indicator light• 200–400°F (93–204°C) solid state

thermostat• Easy front service access to controls

Cooking Capacity & Applications

Effective Cooking Area

Griddle Applications include:

• Pancakes, Eggs, Sausage, French Toast• Burgers, Grilled Onions, Toasted Buns• Grilled Cheese, Sandwiches• Fried Potatoes, Fish, Chicken Breasts,

Philly Steaks, Liver and MORE

Environmental Approvals & Programs

Other Approvals

Options & Accessories

• “U” Channel for connecting 2 griddles• Front mounted condiment board/prep

shelf—8” wide stainless steel• Heavy duty stainless steel stand with

bottom shelf with 5” casters• Condiment Board• Control Guards• Maritime Package (call for details)• Correction Package (call for details)• Chain Package (call for details)

Accu-SteAm™ Griddle eG SerieS

Electric/Steam-Heated, Tabletop Griddle

MM5206-1405

Project: ___________________________________ Location: ___________________________________ Item #: ___________________________________ Quantity:___________

AccuTemp Products, Inc. 8415 North Clinton Park • Fort Wayne, IN 46825 • 800-210-5907 • 260-493-0415 • Fax 260-493-0318 • accutemp.net

EGF-A36 Accu-Steam™Tabletop Griddle

Depth 24” Wide 36” Wide 48” Wide

29” 677 sq. in 1017 sq. in. 1358 sq. in.

24” 558 sq. in. 838 sq. in. 1119 sq. in.

NSF/ANSI 4


MM5206-1405


Accu-Steam Griddle Specifications (replace **** with voltage & phase, i.e. 2083)

Model # EGF****A2400-T1 EGF****B2400-T1 EGF****A3600-T1 EGF****B3600-T1 EGF****A4800-T1 EGF****B4800-T1

KW Input 9.6 kW 9.6 kW 14.25 kW 14.25 kW 14.25 kW 14.25 kW

208/3 Amp Load 26.68 26.68 39.56 39.56 39.56 39.56

240/1 Amp Load 40 40 n/a n/a n/a n/a

240/3 Amp Load 39.58 39.58 34.28 34.28 34.28 34.28

440/3 Amp Load 17.1 17.1 25 25 25 25

480/3 Amp Load 15.41 15.41 22.87 22.87 22.87 22.87

Unit Width (A) 24.25 [616] 24.25 [616] 36.25 [921] 36.25 [921] 48.25 [1226] 48.25 [1226]

Unit Depth (D) 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714]

Cooking Surface Width (B) 23.875 [606] 23.875 [606] 35.875 [911] 35.875 [911] 47.875 [1216] 47.875 [1216]

Cooking Surface Depth (C) 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594]

Depth to Front Leg (E) 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144]

Effective Cooking Area 677 sq. in. 558 sq. in. 1017 sq. in. 838 sq. in. 1358 sq. in. 1119 sq. in.

Grease Pan Capacity 1.5 gal. 1.5 gal. 2 gal. 2 gal. 2 gal. 2 gal.

NEMA Plug (208/240) 15-50P 15-50P 15-50P 15-50P 15-50P 15-50P

NEMA Plug (440/480) L16-20P L16-20P L16-30P L16-30P L16-30P L16-30P


Electric/Steam-Heated, Tabletop Griddle

Notes:1.) Dimensions in brackets [ ] are metric.2.) 5’ power cord wtih plug provided.


Short Specification

Griddle shall be an Energy Star compliant electric-heated unit, with a hermetically-sealed vacuum chamber that produces steam that heats the 8-gauge stainless steel griddle plate. Efficient steam heat transfer provides 200–400°F (93–204°C) operating temperature range and uniform griddle surface temperatures of ±5°F (±3°C). Griddle fabricated from cold-rolled stainless steel with 4.5” high back splash, sides that taper from 4.5” to 1.7”, a 4” wide by 1” deep full front grease trough and 11⁄2–2 gallon grease drawer. Griddle to be mounted on heavy duty stainless steel stand with one undershelf and casters. Unit to be UL listed, UL EPH Sanitation Certified (NSF 4) and manufactured in the USA.



• 8 gauge griddle plate with 4.5” high rear splash and 4.5” to 1.7” tapered side walls

• 4” wide by 1” deep full front grease trough

• 2” x 4” drop chute to 11⁄2–2 gallon capacity grease drawer inside enclosed compartment

• 5” heavy-duty casters standard, front are locking type (optional bullet or flanged feet)




• Steam transfers heat evenly to entire cooking surface with only ±5°F (±3°C) in temperature variation












Other Approvals


• “U” Channel for connecting 2 griddles• Front mounted condiment board/prep

shelf—8” wide stainless steel• Condiment Board• Control Guards• Maritime Package (call for details)• Correction Package (call for details)• Chain Package (call for details)


Electric/Steam-Heated, Stand-Mounted Griddle

MM5205-1405



EGF-A36 Accu-Steam™Stand-Mounted Griddle

(also available with bullet or flanged feet)

Depth 24” Wide 36” Wide 48” Wide

29” 677 sq. in 1017 sq. in. 1358 sq. in.

24” 558 sq. in. 838 sq. in. 1119 sq. in.

NSF/ANSI 4



Accu-Steam Griddle Specifications (replace **** with voltage & phase, i.e. 2083)

Model # EGF****A2400-S2 EGF****B2400-S2 EGF****A3600-S2 EGF****B3600-S2 EGF****A4800-S2 EGF****B4800-S2

KW Input 9.6 kW 9.6 kW 14.25 kW 14.25 kW 14.25 kW 14.25 kW

208/3 Amp Load 26.68 26.68 39.56 39.56 39.56 39.56

240/1 Amp Load 40 40 n/a n/a n/a n/a

240/3 Amp Load 39.58 39.58 34.28 34.28 34.28 34.28

440/3 Amp Load 17.5 17.5 25 25 25 25

480/3 Amp Load 15.41 15.41 22.87 22.87 22.87 22.87

Unit Width (A) 24.25 [616] 24.25 [616] 36.25 [921] 36.25 [921] 48.25 [1226] 48.25 [1226]

Unit Depth (D) 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714]

Cooking Surface Width (B) 23.875 [606] 23.875 [606] 35.875 [911] 35.875 [911] 47.875 [1216] 47.875 [1216]

Cooking Surface Depth (C) 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594]

Depth to Front Leg (E) 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144]

Effective Cooking Area 677 sq. in. 558 sq. in. 1017 sq. in. 838 sq. in. 1358 sq. in. 1119 sq. in.

Grease Pan Capacity 1.5 gal. 1.5 gal. 2 gal. 2 gal. 2 gal. 2 gal.

NEMA Plug (208/240) 15-50P 15-50P 15-50P 15-50P 15-50P 15-50P

NEMA Plug (440/480) L16-20P L16-20P L16-30P L16-30P L16-30P L16-30P


Electric/Steam-Heated, Stand-Mounted Griddle

Notes:1.) Dimensions in brackets [ ] are metric.2.) 5’ power cord with plug provided.

MM5205-1405


Short Specification

Griddle shall be an AccuTemp Model EG modular drop-in electric heated unit, with hermetically-sealed vacuum chamber that produces steam to heat the 8-gauge stainless steel griddle plate. Efficient steam heat transfer provides 200–400°F (93–204°C) operating temperature range and uniform griddle surface temperatures of ±3°F (±1°C). Unit is fabricated in two modules with water and grease resistant front control panel and insulated and sealed griddle cook surface drop-in, fabricated from cold-rolled stainless steel recessed 1.5” below work surface, with 3” wide by 1.25” deep full front grease trough and 1.5-gallon grease drawer. Unit to be UL listed, UL EPH Sanitation Certified (NSF 4) and manufactured in the USA.



• 8 gauge griddle plate with 4.5” high rear splash and 4.5 to 1.7” tapered side walls

• 3” wide by 1.25” deep full front grease trough

• 2” x 4” drop chute to 11⁄2 gallon capacity grease drawer inside enclosed compartment

• Sealed control panel provided for cabinet front mounting




• Steam transfers heat evenly to entire pan surface with only ±5°F (±3°C) in temperature variation












Other Approvals


• Control Guards• Maritime Package (call for details)• Chain Package (call for details)• Control panel available in left mount,

right mount and center mount


Electric/Steam-Heated, Drop-In Griddle

MM5207-1405



EGD-B36 Accu-Steam™Drop-In Griddle

Depth 36” Wide 48” Wide

24” 799 sq. in. 1093 sq. in.

NSF/ANSI 4


MM5207-1405


Accu-Steam Drop-In Griddle Specifications (replace **** with voltage & phase, i.e. 2083)

Model # EGD****B3600-00 EGD****B4800-00

KW Input 14.25 kW 14.25 kW

208/3 Amp Load 39.56 39.56

240/3 Amp Load 34.28 34.28

440/3 Amp Load 21 21

480/3 Amp Load 17.14 17.14

Unit Width (A) 36.5 [927] 49 [1245]

Unit Depth (D) 29.5 [749] 29.5 [749]

Cooking Surface Width (B) 34 [864] 46.5 [1181]

Cooking Surface Depth (C) 23.5 [597] 23.5 [597]

Effective Cooking Area 799 sq in[20295 sq mm]

1093 sq in[27762 sq mm]

Rough Opening Griddle 35.5 x 28.5[902 x 724]

47.75 x 28.5[1213 x 724]

Rough Opening Control Panel

33.75 x 4.875[857 x 124]

33.75 x 4.875[857 x 124]

Grease Pan Capacity 1.5 gal. 1.5 gal.

NEMA Plug (208/240) 15-50P 15-50P

NEMA Plug (440/480) L16-30P L16-30P


Electric/Steam-Heated, Drop-In Griddle

Notes:1.) Dimensions in brackets [ ] are metric.2.) 5’ power cord wtih plug provided.


THEORY OF OPERATION

INTRODUCTIONThe ACCU-STEAM™ griddle is constructed and uses technology like no other griddle in the world. The diagram below is a cross-sectional view of the griddle. The griddle cooking surface is the top of a chamber in which we have produced a unique environment. Welded stainless steel reinforcement studs connect the chamber top to the chamber bottom. The perimeter joints are all robotically welded to produce a vessel that is airtight, which is verified using a helium mass spectrometer. The chamber is filled half full with distilled water. The remaining air is removed and the chamber is welded shut. At this point, the chamber becomes a hermetically sealed vessel, never to be opened again. The griddle steam chamber requires no water or maintenance. A thermowell for a temperature sensor to sense temperature and a thermowell for the over temp safety shutdown system are also welded into the griddle steam chamber.

At temperatures below 212°F (100°C), the chamber is actually in a vacuum, similar to that of a canning jar. At temperatures above 212°F (100°C), the chamber operates under pressure. Located between the water and the bottom of the cooking surface is the best heat transfer medium – steam, the most effective way to transfer heat. The temperature sensor senses the temperature of the steam and reports this data to the thermostat, which energizes the heating elements. This system maintains the griddle cooking surface temperatures to within ± 5°F (2.7°C) over the entire cooking surface and provides a near instant temperature recovery, even in the same spot on the griddle, when turning food in place.


ELECTRIC TABLE TOP & STANDMODEL EGF SERIES

INSTALLATION INSTRUCTIONS


INSTALLATION TABLE TOP/STAND MODEL - EGF SERIES

LOCATION AND PLACEMENTThe ACCU-STEAM electric griddle has been designed to be placed on a commercial kitchen counter-top, an AccuTemp griddle stand or directly onto any flat, level surface that will support the appliance weight.The operating temperature ranges from 200°- 400°F (93°- 204°C). Since these temperatures can also be found on surfaces around the perimeter of the griddle, care should be given not to install griddle next to or against, objects or surfaces with a low melting or flash point.

TOOLS REQUIRED:

Spirit Level Clamp Amp MeterPhillips Screw Driver Weighted Temperature ProbeSmall Blade Straight Screw Driver Digital Temperature MeterDigital Volt Meter

IN-FIELD MODIFICATIONSThis appliance has a totally unique design and is constructed unlike any other griddle on the market today. Any modification may permanently damage the griddle.

Only a qualified service or electrician should complete the installation to ensure that all electrical and safety requirements are met and that all wiring is installed as per all National, State and Local electrical codes.

WARNING

This appliance is heavy. For safe handling, the installer should obtain help as needed or employ appropriate material handling equipment to remove the appliance from the skid and move into the final destination.

WARNING

Any in field modifications made without written authorization from AccuTemp™ will void all warranties

NOTE

LEVELING The appliance must be installed in a level condition. An out-of-level condition may cause uneven temperatures and in a severe out of level condition damage to the appliance can occur. Use a spirit level resting on the appliance cooking surface to ensure it is level front-to-back and left-to-right.

The griddle must be level front to back and side to side. Warranty will be void if not.

WARNING

Any in field modifications that bypasses the safety features could result in injury or death.

WARNING


INSTALLATION TABLE TOP/STAND MODEL - EGF SERIES

ELECTRICAL SUPPLYThe ACCU-STEAM™ griddle has been designed, manufactured and tested to meet or exceed the demanding standards of safety set forth by Underwriters Laboratories, Inc. To to ensure that this high level of safety is maintained in your installation, it is important that you read and understand the following information before attempting to plug in your griddle.

ELECTRICAL REQUIREMENTSElectrical requirements are listed on the data plate located on the right side of the unit, near the front. All standard AccuTemp griddles are supplied with a 6ft (1.83m) cord and the appropriate UL listed plug. Make sure that the voltage at your supply receptacle is within ± 10 % of the voltage listed on the griddle data plate. Connection to any other voltage may cause damage to components in the appliance. The appliance plug must be used with the appropriate receptacle. Direct wiring will void the warranty.

This appliance must be properly grounded, In accordance with all the National, State and local electrical codes.

WARNING

GROUNDING INSTRUCTIONSGrounding provides a path for electric current to reduce the risk of shock. This product is equipped with a power cord having a grounding conductor and a grounding plug.

ELECTRICAL CONNECTIONS (EGF MODELS ONLY)The receptacle requirements vary between models. For a 240 V single-phase model, you will need a NEMA 6-50R receptacle. If you have purchased 208/240V three-phase model, you will need a NEMA 15-50R receptacle and if you purchased a 440V/480V three-phase model you will need a NEMA L16-30R receptacle.

NEMA 6-50R NEMA 15-50R NEMA L16-30R

240V Single 208/240V 3 Phase 440/480V 3 Phase

LEVELING - CONTINUEDTABLE TOPInstall the (4) rubber foot tips provided with your appliance onto the four foot adjusters of each of the appliance legs. This will keep the griddle from sliding on the counter-top under normal use. Once the rubber foot tips have been installed, adjust the four foot adjusters up or down as needed to level the griddle.ACCUTEMP STAND If on an AccuTemp griddle stand with casters, ensure that the floor surface is level and place the two locking casters to the “on” position and follow the leveling instructions to verify the appliance is level.


Fig. 1IntroductionIt is highly recommended that a survey of the kitchen site be conducted to determine the requirements for the installation. Electrical supply, counter space as well as counter arrangement are critical to the choice of Drop-In-Griddle options. The Drop-In-Griddle is available in many options to accommodate size, control panel arrangements and supply voltage. The model data label indicating the model number, phase, voltage, current, wattage and UL™ information is located on the bottom cover of the unit.

Counter designs that have an “L” arrangement such that the shortest part of the “L” is to the left may require a “Right Hand Control Panel” option. A counter design that has an “L” arrangement such that the shortest part of the “L” is to the right may require a “Left Hand Control Panel” option. See Figure 1 for views of these configurations.

INSTALLATION MODEL EGD DROP-IN GRIDDLE

This product is to be installed in stainless or non-combustible counter tops only.

CAUTION

Installation must allow for inspection and serviceability to the underside of the appliance.

NOTE

ELECTRICAL SUPPLYThe ACCU-STEAM™ griddle has been designed, manufactured and tested to meet or exceed the demanding standards of safety set forth by Underwriters Laboratories, Inc. To ensure that this high level of safety is maintained in your installation, it is important that you read and understand the following information before attempting install your griddle.

ELECTRICAL REQUIREMENTSElectrical requirements are listed on the data plate located on the Bottom of the Control Box, near the front. The EGD Series griddles are supplied with a 5 foot (1.52m) cord. Make sure that the voltage at your supply is within ± 10 % of the voltage listed on the griddle data plate. Connection to any other voltage may cause damage to components in the griddle and damage of this type is not covered under warranty.


INSTALLATION MODEL EGD DROP-IN GRIDDLE (cont.)

This appliance must be properly grounded, in accordance with all National, State and local electrical codes.

WARNING

GROUNDING INSTRUCTIONSGrounding provides a path for electric current to reduce the risk of shock. This product is equipped with a 5 foot power cord with a grounding conductor.

GETTING STARTEDPlease read and comprehend all instructions and manuals provided with each Drop-In-Griddle. Read and understand all safety warnings and operator instructions for all powered tools required to complete the installation of the Drop-In-Griddle. Disconnect all power from house supply connection boxes at the appropriate fuse panel and label the breakers “In service”.

This is to warn others that work is in process, preventing accidental electrocution.

TYPICAL TOOLS AND SUPPLIES REQUIREMENTS• Putty knife• Grease solvents• Clean sponges or rags• Latex gloves• Caulking gun• Approximately 3oz. NSF-approved aluminized silicone sealant• Tape measure• Carpenters square• #2 Phillips screw driver• Channel lock pliers• ½ inch box/open wrench• 3/8 inch nut driver• 3/8 inch electric or cordless drill• #25 drill bit• 3/8 inch drill bit• Saber saw with metal cutting blades• Permanent marking pen, preferably a “Sharpie” fine point. • 4 inch grinder. (If replacing an existing competitors griddle, it is recommend to use a 4 inch grinder to

clean off any welds, welded on brackets or framing attached to the counter top.)

1. Inspect the griddle packaging to ensure there are no missing components.Parts Contained in the Packaging:

QTY DESCRIPTION PART NUMBER

1 Griddle Module AT2A-2520

1 Control Panel Assembly AT2A-2772

1 Cable Assembly - 24 inch AT2A-2764-1

1 Grease Spout Extension - 1” AT2A-2592-1

1 Grease Spout Extension - 2” AT2A-2592-2

1 Grease Spout Extension - 3 “ AT2A-2592-3

1 Grease Spout Extension - 4 “ AT2A-2592-4



Fig. 2

QTY DESCRIPTION PART NUMBER

8 Screw, #10 Type AB x 1/2 Truss Head AT0F-2777-41040

6 Screw, 10-24 UNC x 1/2 inch Phillips Round Head Machine AT0F-2755-41040

2 Bolt, 5/16 -18 UNC 2A 3/4” Carriage AT0F-1921-61060

2 Washer, 5/16 “ Helical Spring Lock AT0F-1922-60000

2 Nut, 5/16-18 x UNC 2B SS Hex Machine AT0F-2778-61000

8 1/4-20 Nyloc Nut AT0F-2691-51002

4 Retainer Brackets AT2M-2535-1

1 Grease Trough Hngr Brkt AT2M-2553-1

1 Grease Trough Hanger AT2M-2554-1

6 Washer, #10 Internal Tooth Lock AT0F-2666-40000

1 Grease Trough Assembly AT2A-2529

1 Grease Tray Assembly AT2A-2552

1 Electric Griddle Owners Manual MP5004

1 Registration Card AT0T-3033-1

2. Complete the appropriate power disconnection procedures for existing equipment or local power junction boxes.

3. Clean surfaces with grease solvents and dry off with clean rags or sponges.

4. Determine the location and orientation for the griddle and control panel modules. Mark the center line on the counter top for the griddle module, using a Carpenter’s square. See Figure 2 for the counter top and control panel layouts. Continue the center line to the control panel module mounting surface. Accurate center line alignment of the counter top and control panel modules is critical to ensure the correct alignment of the grease trough assembly to the griddle module.

Parts Contained in the Packaging:


INSTALLATION MODEL EGD DROP-IN GRIDDLE (cont.)5. The dimensional relationship between the griddle module mounting flange and the control

panel module is shown in Figure 3. The griddle module mounting flange overlaps the counter top cutout by 0.50 inches on all four sides. Mark the griddle module cutout on the counter top such that the front edge of the griddle module is 0.73 inches – 2.63 inches from the control panel module mounting surface, as shown in Figure 3. Mark the control panel module cutout on the control panel module mounting surface, as shown in Figure 2.

Fig. 3

6. Cut out the griddle and control panel module openings. Straighten out any dings or bent edges in both cutouts to ensure adequate sealing between the new griddle and the counter top surface and between the control panel and the front surface of the counter.

7. Drillthemountingholesinthefaceofthecounterusinga#25drillbit.Drillthefirstsetofholesandlocate the remaining holes using the control panel as a template.

8. Use a lifting device, if possible, to raise the griddle module above the counter and position over cutout in counter top. Lower the griddle module carefully into the cutout. Install the retainer clamps to the griddle module, using the ¼-20 nyloc nuts (see drawing AT2A-3044, sheet 6).

9. Install the control panel onto the counter face using #10-24 x 3/8 inch self-tapping screws. Also, at this time, install the thermostat knob guard, if necessary, by lining up the holes on the guard to the holes on the control panel directly above and below the thermostat.

10. Install the grease trough hanger brackets onto the bottom side of the griddle using (2) #10-24 X ½ inch Phillips round head machine screws and (2) 5/16-18 X ¾ inch carriage head bolts with (2) 5/16 inch lock washers and (2) 5/16-18 nuts (see drawing AT2A-3044, sheet 6). Leave the carriage bolts loose for adjustment of the grease trough.

11. Install the grease trough using (4) #10-24 X ½ inch Phillips round head machine screws through the front panel opening and through the hanger bracket assembly, installed in step 10.

12. Adjust the hanger bracket height so that the grease trough is setting level front-to-back and tighten the 5/16-18 nuts.

13. Install the appropriate size grease spout extension onto the griddle grease spout, that ensures the bottom



ofthegreasespoutextensionisflushtotheinsidesurfaceofthegreasetroughassembly(seedrawingAT2A-3044, sheet 6).

14. Use the caulking gun to lay a 1/8” minimum diameter bead of the aluminized silicone sealant around the griddlemodulemountingflangeontothecountertop.Useaglovedfingertowipethesealantintoafilletshape.

15. Install the interconnect cable between the control panel module and the control box, mounted on the bottom side of the griddle (see drawing AT2A-3044, sheet 6).

16. Set the on/off switch to the off position and set the temperature control knob to the lowest setting.17. Install the power cord into an appropriate sized electrical connection box with an appropriate sized cord

griporcablestrainrelief.Completethefinalconnections,testingthehousesupplywirefirsttoensureitis not live.

18. Turn on power to the griddle at the fuse panel.19. Turn the griddle on and set the temperature control knob to a 350°F. Allow the griddle heat light to

cycle a minimum of two times before checking the temperature. Then use a weighted temperature probe and a digital temperature-measuring device to check the griddle surface temperature. The surface temperature should be within 5 – 7 °F of the temperature control knob setting. If it is not, go to the calibration section and follow the calibration procedures.


OPERATIONMODEL EGD & EGF


SEASONINGIt is recommended that you clean your ACCU-STEAM™ griddle thoroughly before using it for the first time. To clean the griddle surface, just simply wash the cooking surface down with a solution of mild soap and water, and then rinse thoroughly with clean water.

Once the cooking surface has been cleaned, set the thermostat to 200°F (93°C), turn the griddle power switch to the “On” position and allow the griddle cooking surface to heat for 10 minutes. Using a high temperature oil, such as Pan and Grill Shortening™, Whirl™ or equivalent, pour enough to cover the entire griddle surface. Do not use standard vegetable oil to season the griddle cooking surface. It may cause food to stick and result in improperly cooked food. Work this seasoning oil into the griddle surface with a regular heavy-duty scrub pad for about 5 minutes, making sure that you scrub the seasoning oil over the entire griddle-cooking surface. After the entire griddle surface has been scrubbed with seasoning oil for 5 minutes, simply wipe or squeegee off excess oil from griddle surface. Your griddle is now ready to use!If you use chemicals to clean your griddle periodically or on a schedule, you may need to repeat this process after the use of chemicals.

PREHEATINGTurn On switch to the “On” position and set the thermostat to the desired temperature. The griddle will increase its surface temperature at an average rate of 15° F (8°C) per minute. It takes approximately 22 minutes to raise the griddle from room temperature to its maximum temperature of 400° F (204°C). The griddle will be preheated when the “Heat” light starts to cycle on and off. Please use caution as temperatures on and around the griddle cooking surface could cause severe burns.

COOKINGBegin cooking only after the griddle has been preheated to the desired temperature. Please note these facts:

• You can cook all the way to the edges of the griddle surface because the temperature does not very across the entire cooking surface.

• You can turn the product to the same spot because the griddle has near instant heat recovery.

• It will always cook the same, regardless of product load or surface coverage.Accurate Cooking TemperaturesBecause of the inaccurate surface temperatures and long recovery times common with other griddles. It is doubtful you were cooking at the set temperature or the temperature you wanted. Adjust the temperature on your ACCU-STEAM™ griddle and it will not change or vary by the location on the griddle surface. There are no hot or cold zones.

Heat LampIt is normal for the heat light to cycle on and off. This light indicates when the heaters are energized. You will soon notice how little they are energized to maintain perfect surface temperatures on your griddle.

OPERATION


OPERATION (cont.)

Weighted Temperature Probe Digital Temperature Reading Device

Due the construction material of the griddle cooking surface an infrared temperature probe can’t be used. The proper measurement tools to use are a weighted temperature probe and digital temperature as shown below. ( Fig. 5)

CHECKING SURFACE TEMPERATURE

Fig. 5

Accu-Steam™ Installation and Owners ManualMP5004-1605


CLEANINGMODEL EGD & EGF


DAILY CLEANINGCleaning the cooking surface during the work shift can be performed with a sharp scraper. When heavy cleaning at the end of a shift or periodically through the day is needed, the following is recommended:

• Empty the grease pan as often as needed and always prior to end of shift cleaning. • Turn the griddle off and allow it to cool to between 220°F and 240°F (104°C and 116°C). Scrap off

heavy deposits and remove any standing grease before proceeding with the cleaning process.• Use water, ice and/or griddle cleaner as needed. For example, the 3M Scotch-Brite™ Quick Clean

Griddle System provides the Scotch-Brite polishing pads, quick clean liquid, pad holder and squeegee. Clean-up is very easy using these tools with the quick clean liquid, water, ice or combinations of these liquids.

• Empty the grease pan after and wash with a mixture of dish detergent and clean water and dry with a clean dry cloth after the clean the non-cooking surfaces with a damp cloth and dry with a clean dry cloth after the surface is cool to the touch. Use a high quality stainless steel cleaner on a clean cloth to keep these surfaces

• Seasoning the griddle after the daily cleaning is recommended.

NOTEDo not use a appliance stone or brick to clean griddle cooking surface. Only use a fabric scrub pad.

NOTEDo not use a water-jet to clean the griddle as it can harm the electronic components in the appliance.

Grease PanUse caution when emptying the grease pan. The contents in this pan could cause severe burns. The pan should be checked periodically and emptied as necessary to prevent an overflow or dangerous condition.

The grease can contents could cause severe burns. Slowly remove the grease can from the griddle to avoid spilling the contents

WARNING

CAUTIONIf the cooking surface of the appliance has standing grease and the griddle is at a high temperature using water or ice can cause the grease to splatter and cause skin burns.


SERVICE & TROUBLESHOOTINGMODEL EGD & EGF


WARRANTY PROCEDURE

An AccuTemp Products, Inc. Technical Service Technician is available: Monday thru Sunday, 7:00am to 7:00pm EST.

SERVICE AND TROUBLESHOOTING (cont.)

1. Contact the AccuTemp Technical Service group for all warranty service requests.2. Be prepared to supply the serial number, address, location phone and contact for the location.3. Be prepared to complete a few simple tasks to help evaluate the problem.4. If the problem requires service at the location the AccuTemp Technical Service group will dispatch

the nearest authorized service agent.

NOTEService should be completed by AccuTemp authorized service groups. Service completed by unauthorized groups will void all factory warranties.

NOTEAccuTemp™ Technical Service group must be contacted for all warranty service requests or the warranty claim my be denied.

Toll Free 800 480-0415Office 260 469-3040Fax 260 469-3045Email -Service [email protected] [email protected] Site www.accutemp.net


BASIC TROUBLESHOOTING

Griddle will not turn on• Make sure the griddle is plugged in and the “On/Off” switch is in the On position.• Check for a facility circuit breaker (or fuse) supplying the unit

Heat light will not come on• Make sure the griddle is not hotter than the temperature you have it set for. If you have

turned down the temperature of the griddle, the heat light will not come on again until the cooking surface drops below the temperature you have set.

• See if the heat light is coming on intermittently. While operating in a normal condition, the heat light cycles on and off periodically when at temperature.

Uneven or inaccurate surface temperatures• Verify griddle is level front to back and side to side.• Verify the surface temperature with an accurate digital surface probe thermometer. • Use of an infrared thermometer will not give an accurate reading of the griddle surface

temperatures.• Contact AccuTemp Technical Service for additional instructions.

Unit will not turn off• This system, which is extremely rare, indicates a serious control malfunction. • Turn off the griddle’s electrical supply at the source and contact AccuTemp Technical Service

for additional Instructions.

SERVICE AND TROUBLESHOOTING

Use of any replacement parts other than those supplied by AccuTemp can cause injury to the operator or damage the appliance and voids all warranties

WARNING

There are no user-serviceable parts. To prevent electrical shock do not open the access panel covers.

WARNING

Any in-field modification that bypass the built in safety features of this appliance will result in death or serious injury.

WARNING

NOTEService should be completed by Accutemp™ authorized service groups. Service completed by unauthorized groups will void all factory warranties.


SERVICE PARTSMODEL EGF


ITEM PART NUMBER DESCRIPTION

1 AT0E-1800-5 INDICATOR LAMP RED 250V

2 AT0E-1800-4 INDICATOR LAMP GREEN 250V

3 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH

4 AT0F-1046-31030 SCREW,#8-32 X 3/8 PHLP TRUSS HEAD


6 AT0F-3371-1 NUT ROTARY SHAFT SEAL

7 AT0E-3189-1 ASSY, EG EXTERNAL THERMOSTAT

8 AT2G-1026-1 GASKET, CONTROL PANEL EG

9 AT0E-2559-7 THERMOSTAT, RTD

10 AT0E-3339-1 MOUNTING LATCH

11 AT0E-3338-1 CONTACT BLOCK

12 AT0A-2876-1 MDR WITH TERMINALS

13 AT0F-2777-31030 SCREW #8 TYPE AB X 3/8 TRUSS HD

14 AT2M-1559-1 COVER

15 AT2A-2916-1 HIGH LIMIT OVERTEMP ASSEMBLY (See Page 8)

16 AT0E-2885-3 SENSOR, REPLACEABLE, RTD

17 AT0F-2755-41070 SCREW, #10-24UNCX7/8 PHILIPS ROUND HEAD MACHINE

18 AT0E-1134-4 4 POSITION TERMINAL BLOCK

19 AT0E-3025-2 INSULATOR STRIP, DOUBLE ROW

20 AT0F-2691-41002 NUT, 10-24 NYLOC

1

3

2

4 5 6 7 8

9

10 11

13

15

1412

16

17 19

20

18

21

2422

23

2625

2827

29 30

3332

31

34

MODEL EGF COMMERCIAL MODELS

SEE PAGE 8



21 AT0F-2662-3 TRANSFORMER 440V,480V22 AT2A-3032-3 4” LEG ASSEMBLY, FLANGE, OPTIONAL

22.1 AT2A-3032-1 4” LEG ASSEMBLY, STANDARD (NOT SHOWN)22.2 AT2A-3032-2 8” LEG ASSEMBLY, OPTIONAL (NOT SHOWN)23 AT0F-2875-51062 SCREW, 1/4-20UNC x3/4 HEX HEAD MACHINE 24 AT0E-1587-1 3 POLE CONTACTOR25 AT0F-2755-41040 SCREW, #10-24UNC X1/2 PHILPS ROUND HEAD MACHINE26 AT0F-1046-31030 SCREW, #8-32 X 3/8 PHLP TRUSS HEAD27 AT2M-1021-1 PANEL, EGF ACCESS POWER TERMINAL28 AT2G-1022 GASKET, EGF ACCESS POWER TERMINAL29 AT0E-1049-5 CONNECTOR, 1” HUB STRAIN RELIEF30 AT0A-2788-14 POWER CABLE ASSEMBLY - 440V

30.1 AT0A-2788-17 POWER CABLE ASSEMBLY - 208V/3 PHASE (NOT SHOWN)30.2 AT0A-2788-18 POWER CABLE ASSEMBLY - 240V/SINGLE PHASE (NOT SHOWN)30.3 AT0A-2788-19 POWER CABLE ASSEMBLY - 480V/3 PHASE31 AT2M-3183-1 BAR, 24” GRIDDLE GRAB (OPTIONAL)

31.1 AT2M-3183-2 BAR, 36” GRIDDLE GRAB (OPTIONAL) ( NOT SHOWN) 31.2 AT2M-3183-3 BAR, 48” GRIDDLE GRAB (OPTIONAL) (NOT SHOWN) 32 AT2H-3184-1 END BRKTS, GRIDDLE GRAB BAR (OPTIONAL) 33 AT0F-2778-71001 NUT, 3/8-16UNC-2B 11 HEXMACHINE SCREW

MODEL EGF COMMERCIAL MODELS


MODEL EGF MARITIME MODELS

ITEM NUMBER PART NUMBER DESCRIPTION

1.1.2 AT2A-2185 WELD ASSY, CHAMBER

2 AT2M-1021-1 PANEL, EGF ACCESS POWER TERMINAL

3 AT2G-1022 GASKET PANEL ACCESS POWER TERMINAL, EG

4 AT2A-3189-1 ASSY, EXT THERM CONTROL PANEL

4.1 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH

4.2 AT0H-1455-2 KNOB FOR D SHAFT

4.3 AT0E-2559-7 TEMPERATURE CONTROLLER, RTD

4.4 AT0E-1800-4 INDICATOR LAMP GRN NEON 250V

4.5 AT0E-1800-5 INDICATOR LAMP RED NEON 250V

4.6 AT0E-3338-1 CONTACT BLOCK

4.7 AT0E-3339-1 MOUNTING LATCH

4.8 AT0F-3371-1 NUT, ROTARY SEAL

5 AT0G-1026-1 GASKET, CONTROL PANEL, EG

6 AT0E-1587-1 3 POLE CONTACTOR

7 AT0E-2662-3 TRANSFORMER

8 AT2A--2916-1 HIGH LIMIT OVER TEMP ASSEMBLY

9 AT2M-1559-1 COVER


11 AT0E-3025-2 INSULATOR STRIP, DOUBLE ROW

16 AT0E-1049-5 CONNECTOR, 1” HUB STRAIN RELIEF

17 AT0A-2788-14 POWER CABLE ASSEMBLY

17.2 AT2E-2567-6 CABLE 6 AWG 4 COND




18 AT2A-2529-2 GREASE TROUGH ASSY

19 AT2A-2552-2 ASSY, BAFFLED LOCKING GREASE TRAY

19.1 AT0F-1046-41040 SCREW, #10-24X 1/2 PHLP TRUSS HEAD

19.2 AT2M-2551-2 GREASE TRAY FACE PLATE

19.3 AT2M-3008-1 LEVER, GREASE PAN

19.4 AT0F-3012-1 SPACER, ROUND

19.5 AT0F-1052-43010 WASHER, # 10 TYPE B CUSTOM

19.6 AT0F-1922-40000 WASHER, #10 SS HELICAL SPRING LOCK

19.9 AT0F-2632-41001 NUT, A0-24 ACORN

20 AT2A-3032-3 3” LEG ASSEMBLY

21 AT0F-2755-41050 SCREW, #10-24UNC X 5/8 PHILIPS ROUND HEAD MACHINE

22 AT0-1046-31030 SCREW, #8-32 X 3/8 TYPE AB PHILIPS TRUSS HEAD


24 AT0F-2777-31030 SCREW, #8-32 X 3/8 TYPE AB TRUSS HEAD

25 AT0F-2691-41002 NUT, #10-24 NYLOC

26 AT0F-2875-51062 SCREW, 1/4-20UNC X 3/4 HEX HEAD MACHINE

29 AT0F-2778-71001 NUT, 3/8 UNC SS

30 AT0F-2875-71080 SCREW, 3/8-16UNC X 1 HEX HEAD MACHINE

31 AT0H-3184-1 END BRKTS, GRIDDLE GRAB BAR

32 AT2M-3183-2 36” GRIDDLE GRAB


35 AT0E-2885-3 SENSOR REPLACEABLE, RTD

56 AT2A-3227-2 ASSY, 36” GRIDDLE FRONT 36” SKIRT

57 AT2M-3464-5 SKIRT, FRONT 36” MARITIME

56.2 AT0F-2668-1 NUTSERT, 10-24 HEX



1 AT2M-3103-1 CHASSIS, RELAY ENCLOSURE

2 AT2M-3104-1 COVER RELAY ENCLOSURE

3 AT0H-2576-1 GROMMET, 7/8 NYLON

4 AT0E-2206-3 HEAT SINK, 3.43” LONG

5 AT0E-2296-1 PAD, SSR HEAT SINK

6 AT0E-2059-3 RELAY SOLID STATE

7 AT0A-3111-1 CONTROL INPUT HARNESS

8 AT0A-3111-2 CONTROL INPUT HARNESS

9 AT0A-3112-4 ASSY, HARNESS

10 AT0A-3112-3 ASY, HARNESS

11 AT0A-3112-2 ASSY, HARNESS

12 AT0A-3112-1 ASSY HARNESS

13 AT0F-2755-31040 SCREW, #8-32UNC X 1/2 PHILLIPS ROUND HEAD MACHINE

14 ATOF-2666-40000 WASHER, #8 INTERNAL TOOTH LOCK

15 AT0F-2755-31040 SCREW, #10-24UNC X 1/2 PHILLIPS ROUND HEAD MACHINE

16 AT0F-2666-40000 WASHER INTERNAL TOOTH LOCK

17 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED

24 AT0F-2668-1 NUTSERT, #10-24 HEX



C

Title:

Rev.Drawing No.:


1 AT2A-3243-1 ASSY, EG CONTROL PANEL WELDMENT




6 AT0E-2559-7 TEMPERATURE CONTROLLER

7 AT0E-1455-2 KNOB FOR D SHAFT

8 AT0E-1800-4 INDICATOR LAMP GRN NEON 250V

9 AT0E-1800-5 INDICATOR LAMP RED NEON 250V

10 AT0E-2715-3 OVERLAY CONTROL PANEL

13 AT2A-3283-1 ASSY, WIRE HARNESS

14 AT2G-1026 GASKET CONTROL PANEL, EG

16 AT0F-3371-1 NUT, ROTARY SHAFT SEAL

CONTROL PANEL MODEL EGF COMMERCIAL & MARITIME AT2A-3189



1 AT2M-2861-1 WIRE ROD, OVER TEMP

2 AT2M-2860-1 SOLDER WASHER OVER TEMP

3 AT0F-1367-1 WASHER, TYPE A

4 AT2H-1365-1 COMPRESSION SPRING

5 AT2M-1558-2 BRACKET SWITCH

6 AT2H-1640-1 EXTENSION SPRING

7 AT2E-1639-1 MICRO-SWITCH

8 AT0F-2691-21002 NUT, #6-32 NYLOC

9 AT0F-1052-51002 WASHER 1/4 TYPE B PLAIN ZINC PLATED

10 AT0F-2755-21102 SCREW, #6-32UNC X 1 1/4 PHILI ROUND HEAD MACHINE


HIGH LIMIT OVER TEMP ASSEMBLY MODEL EGF COMMERCIAL & MARITIMEAT2A-2916-1


SERVICE PARTSMODEL EGD


17

15

1234

14

9

35

2

75

8

6

8

1

33

3

11

34

35

3413

30

31

37

36

33

2625 28 28 22 19

3

16

40

41

32

4

33

42

33

MODEL EGD DROP-IN ASSEMBLY AT2A-2520



1 AT2A-2514-2 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36

1A AT2A-2514-3 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B48

1B AT2A-2514-5 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2403B36, EGD4403B36, EGD4803B36

1C AT2A-2514-6 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2403B48, EGD4403B48, EGD4803B48

2 AT2A-2533-1 BOTTOM PAN ASSY-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36

2A AT2A-2533-2 BOTTOM PAN ASSY-MODEL EGD2083B48, EGD2403B48 EGD4403B48, EGD4803B48

3 AT2E-2700-1 TERMINAL INSULATOR

3A AT2E-2700-2 TERMINAL INSULATOR-MODEL EGD2083B48, EGD2403B48 EGD4403B48, EGD4803B48

4 AT2A-2916-2 HIGH LIMIT OVERTEMP ASSEMBLY

5 AT2I-2523-2 INSULATION-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36

1 AT2A-2514-2 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36

1A AT2A-2514-3 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36

1B AT2A-2514-5 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36

1C AT2A-2514-6 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36

2 AT2A-2533-1 BOTTOM PAN ASSY-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36

2A AT2A-2533-2 BOTTOM PAN ASSY-MODEL EGD2083B48, EGD2403B48 EGD4403B48, EGD4803B48

3 AT2E-2700-1 TERMINAL INSULATOR

3A AT2E-2700-2 TERMINAL INSULATOR-MODEL EGD2083B48, EGD2403B48 EGD4403B48, EGD4803B48

4 AT2A-2916-2 HIGH LIMIT OVERTEMP ASSEMBLY


5A AT2I-2523-3 INSULATION-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48





8B AT2I-2523-10 INSULATION-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48, EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48

9 AT2A-2577-4 CONTROL BOX ASSEMBLY

11 AT2M-1559-2 COVER

12 AT0E-1049-1 CONNECTOR, 1 1/4” HUB STRAIN RELIEF-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48

12A AT0E-1049-2 CONNECTOR, 3/4” HUB STRAIN RELIEF-MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48

13 AT0A-2736-5 MOV- TERMINALS ASSEMBLY-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48

MODEL EGD DROP-IN ASSEMBLY AT2A-2520



13A AT0A-2736-6 MOV- TERMINALS ASSEMBLY-MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48

14 AT0E-2086-2 CORD GRIP LOCKNUT-MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48

14A AT0E-2086-4 CORD GRIP LOCKNUT-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48

15 AT0A-2788-1 POWER CABLE ASSY-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48

15A AT0A-2788-3 POWER CABLE ASSY-MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48

16 AT2L-2713-7 SCHEMATIC LABEL, GRIDDLE-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48,

16A AT2L-2713-9 SCHEMATIC LABEL, GRIDDLE MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48

17 AT0L-2798-1 OVERLAY, WARNING, ELECTRICAL

18 AT0A-2617-7 25.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36




22 AT0A-2617-8 27.0” HIGH TEMP WIRE ASSEMBLYWHITE- MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36

23 AT0A-2617-10 32.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL, EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48

25 AT0A-2617-4 12.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48, EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48



30 AT2A-2758-2 CABLE ASSEMBLY OT-EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36

30A AT2A-2758-3 CABLE ASSEMBLY OT-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48

31 AT2L-3725-1 DATA TAG, ELECTRIC GRIDDLE



34 AT0F-2777-31030 SCREW, #8 TYPE AB X 3/8 TRUSS HD


36 AT0F-2666-40000 WASHER, #10 INTERNAL TOOTH LOCK



37 AT0F-2778-41001 NUT, #10-24UNC-2B SS HEX MACHINE SCREW

38 AT2M-2768-1 PLATE, ADAPTER


40 AT0H-2576-2 GROMMET, 1¼” NYLON

41 AT0E-2885-5 SENSOR, REPLACEABLE

42 AT2M-2646-1 COVER CONTROL BOX


MODEL EGD DROP-IN GRIDDLE CONTROL BOX ASSEMBLY AT2A-2577


1 AT2M-2560-3 BOX, CONTROL

2 AT0E-1587-4 3 POLE CONTACTOR


5 AT0E-3025-2 INSULATOR STRIP, 4 POSITION DOUBLE ROW

6 AT0E-2708-1 3AG OMNI-BLOK FUSE BLOCK 2 POS

7 AT0E-2731-2 FUSE 1¼ AMP 250V

8 AT0E-2662-5 TRANSFORMER

9 AT0A-2736-8 MOV- TERMINALS ASSEMBLY

10 AT0H-2887-1 CABLE TIE MOUNT

11 AT0E-2206-3 HEAT SINK, 3.47” LONG

12 AT0E-2059-3 RELAY, SOLID STATE



MODEL EGD DROP-IN GRIDDLE CONTROL BOX ASSEMBLY AT2A-2577









22 AT0F-2668-1 NUTSERT, #10-24 HEX

23 AT0F-2666-30000 #8 LOCK WASHER INTERNAL TOOTH

24 AT0A-2761-1 CABLE GROUND WIRE ASSY

25 AT0A-2615-2 WIRE HARNESS



28 AT0A-2617-1 5.0” HIGH TEMP WIRE ASSEMBLY WHITE

29 AT2A-2760-6 CABLE ASSEMBLY

30 AT0A-2617-3 5.0” HIGH TEMP WIRE ASSEMBLY RED

31 AT0A-2617-31 6.0” HIGH TEMP WIRE ASSEMBLY RED

32 AT0A-2617-32 7.0” HIGH TEMP WIRE ASSEMBLY BLACK

33 AT0A-2617-33 8.0” HIGH TEMP WIRE ASSEMBLY BLACK

34 AT0A-3178-1 HARNESS ASSEMBLY FORK TERM TO FORK TERM

35 AT0A-3178-2 HARNESS ASSEMBLY FORK TERM TO FORK TERM


21

3

6

23

7

20

18

16

19

1

4

14

5

22

9

11

10

17

2

24


1 AT2A-2592-1 1” GREASE SPOUT EXTENSION




5 AT2A-2529-1 GREASE TROUGH ASSY

5A AT2A-2529-3 GREASE TROUGH ASSY

6 AT2A-2552-1 GREASE TRAY ASSEMBLY

6A AT2A-2552-3 ASSY, LONG BAFFLED LOCKING GREASE TRAY

7 AT2A-2764-1 CABLE ASSEMBLY

9 MP5004 ELECTRIC GRIDDLE OWNERS MANUAL

10 AT2M-2553-1 GREASE TROUGH HNGR BRKT

11 AT2M-2554-1 GREASE TROUGH HANGER

14 AT0L-2716-1 OVERLAY, LOGO, ACCUTEMP



18 AT0F-1921-61060 BOLT, 5/16-18 UNC 2A X 3/4” CARRIAGE

19 AT0F-1922-60000 WASHER, 5/16” HELICAL SPRING LOCK

20 AT0F-2778-61000 NUT, 5/16-18UNC-2B SS HEX MACHINE SCREW

21 AT0F-2691-51002 NUT, ¼-20 NYLOC

22 AT2M-2535-1 RETAINER BRACKET

23 AT0F-2666-40000 WASHER, #10 INTERNAL TOOTH LOCK

24 AT0T-3033-1 PRODUCT REGISTRATION FORM

MODEL EGD DROP-IN GRIDDLE LOOSE PIECE KIT AT2A-2772


AT2A-2526-5CONTROL PANEL ASSY - RH

OTHERWISE SAME AS AT2A-2526-4

1

18

AT2A-2526-4

1

17

CONTROL PANEL ASSY - FULLOTHERWISE SAME AS AT2A-2526-1

G

G19

2

AT2A-2526-4CONTROL PANEL ASSY - FULL

5 9 11

F

121

15

7

8

4

16

3

6 11

OTHERWISE SAME AS AT2A-2526-4CONTROL PANEL ASSY - LH

AT2A-2526-6

1


1 AT2A-2565-1 CONTROL PANEL WELD ASSY - FULL

1A AT2A-2565-2 CONTROL PANEL WELD ASSY- RH

1B AT2A-2565-3 CONTROL PANEL WELD ASSY - LH

2 AT2M-2566-1 CONTROL PANEL COVER

3 AT2M-2566-1 KNOB FOR D SHAFT




7 AT0E-1800-1 INDICATOR LAMP GRN LED 28V

8 AT0E-1800-2 INDICATOR LAMP RED LED 28V

10 AT2A-2762-1 HARNESS ASSEMBLY

11 AT0F-2691-41002 NUT, #10-24 NYLOC


15 AT2L-2715-1 OVERLAY, CONTROL PANEL

16 AT2M-2907-1 THERMOSTAT GUARD BRKT

17 AT2A-2762-2 HARNESS ASSEMBLY

18 AT0E-2559-6 TEMPERATURE CONTROLLER

19 AT0F-3371-1 NUT, ROTARY SHAFT SEAL



1 AT2M-2861-1 WIRE ROD, OVER TEMP

2 AT2M-2860-1 SOLDER WASHER OVER TEMP

3 AT0F-1367-1 WASHER, TYPE A

4 AT2H-1365-1 COMPRESSION SPRING

5 AT2M-1558-2 BRACKET SWITCH

6 AT2H-1640-1 EXTENSION SPRING

7 AT2E-1639-1 MICRO-SWITCH

8 AT0F-2691-21002 NUT, #6-32 NYLOC

9 AT0F-1052-51002 WASHER 1/4 TYPE B PLAIN ZINC PLATED

10 AT0F-2755-21102 SCREW, #6-32UNC X 1 1/4 PHILI ROUND HEAD MACHINE


HIGH LIMIT OVER TEMP ASSEMBLY EGD MODELSAT2A-2916-1


SCHEMATICSMODEL EGF


ACCUSTEAM ELECTRIC SERIES SCHEMATICMODEL EGF

208/240V 3 PHASE

AT2T-3640-1 REV A

Size (inches) Voltage Ohms

24 208 13.52

24 240 18

36 & 48 208 9.11

36 & 48 240 12.13

ELEMENT SPECIFICATION



240V SINGLE PHASE

AT2T-3640-2 REV A

Size (inches) Voltage Ohm

24 240 18




440V/480V 3-PHASE

AT2T-3640-4 REV A



24 440 13.52

24 480 18

36 & 48 440 9.11

36 & 48 480 12.13



380V-435V 5 WIRE

AT2T-3640-3 REV A


Size (inches) Voltage Ohms per Element

24 380 18

24 415 18

24 440 18

24 480 18

36 & 48 380 9.11

36 & 48 415 12.13

36 & 48 440 12.13

36 & 48 480 12.13


SERVICE PARTSMODEL EGD


L

OR

N

YE

L

RED

WHT

BLK

GRN

WHT

WHT

BLK

BLUBLU

BLK

FINAL SELECTION OF PRIMARY VOLTAGE TO BE MADE IN FINAL ASSEMBLY

480V

440V

240V

208V

COM

AT0E-2662-5

24V

F1

F23AG .5A

AT0E-2731-1

41

26

3

L3

L1

L2

5

BLK

WHT

RED

N

R1 R3

R2

ZR2

WHT

RED

BLK

ZR1

RED

AT2E-1587-4

AT0E-2736-5

AT0E-2736-8

RLY 1

ZR4

L3

L2

L1

WHT

SSR 1 SSR 2

1 P

3 2

1 J3

2SW2

O.T. SW

N.O.

N.C.

1 P

4 2

1 J4

2

RED

RED

BLK

BLKAT2A-2916-2

AT0A-2758-1

1 P5 2

1 J5 2

WHT

1 2 3 4 5 6 7J2

1 2 3 4 5 6 7P1

P21 2 3 4 5 6 7

WH

T

RE

D

OR

N

RED

BLK WHT

ORN

GRNBLU

WHT/BLK

GR

N

CONTROL PANEL

BLK CONTACTOR

ENCLOSURE

AT2A-2764-1

AT2A-2760-5

AT0A-2761-1

YEL

RED

J11 2 3 4 5 6 7

ON/OFFSW1 PWR

LT1HEATLT2

BLK

RED

WHT

ORN

YE

L

CONTROL PANEL

AT2E-1755 AT0E-1800-1 AT0E-1800-2

AT2A-2762-2

BLU BLU

PRTD

RED RED

WHT

OR

N

1 3 5 6 8 9 L1 L2 OUTPUT PRTD

PRTD TYPE CONTROLLER CAL OFFSET ADJ

to

ANALOG CONTROLER

MODEL EGD DROP-IN 208/240V DELTA SSR HEATER CONFIGURATIONAT2T-2713-7


24 208 13.52

24 240 18

36 & 48 208 9.11

36 & 48 240 12.13



OR

N

YEL

RED

WHT

BLK

GRN

WHT

WHT

BLK

BLUBLU

BLK


480V

440V

240V

208V

COM

AT0E-2662-5

24V

F1

F23AG .5A

AT0E-2731-1

BLK

WHT

RED

ZR2

WHT

RED

BLK

ZR1

RED

AT2E-1587-4

AT0E-2736-5

AT0E-2736-8

RLY 1

ZR4

L3

L2

L1

WHT

SSR 1 SSR 2

1 P3

2

1 J3

2

SW2O.T. SW

N.O.

N.C.

1 P4

2

1 J4

2

RED

RED

BLK

BLK

AT0A-2758-1

1 P5 2

1 J5 2

WHT

1 2 3 4 5 6 7J2

1 2 3 4 5 6 7P1

P21 2 3 4 5 6 7

WH

T

RED

OR

N

RED

BLK WHT

ORN

GRNBLU

WHT/BLK

GR

N

BLK

CONTACTOR ENCLOSURE

AT2A-2764-1

AT2A-2760-5

AT0A-2761-1

YEL

RED

J11 2 3 4 5 6 7

ON/OFFSW1 PWR

LT1HEATLT2

BLK

RED

WHT

ORN

YEL

CONTROL PANEL

AT0E-1800-1 AT0E-1800-2

AT2A-2762-2

BLU BLU

PRTD

RED RED

WHT

OR

N



to

ANALOG CONTROLER

BLK

WHT

RED

R1 R3

R2

5

1

6

3

L3

L1

L2

N4 2

MODEL EGD DROP-IN 440/480V WYE SSR HEATER CONFIGURATIONAT2T-2713--8


24 208 13.52

24 240 18

36 & 48 208 9.11

36 & 48 240 12.13



OR

N

YE

L

WHT

BLK

GRN

WHT

WHT

BLK

BLUBLU

BLK


480V

440V

240V

208V

COM

AT0E-2662-5

24V

F1

F23AG .5A

AT0E-2731-1

BLK

WHT

WHT

BLK

ZR1

RED

AT2E-1587-4

AT0E-2736-5

AT0E-2736-8

RLY 1

ZR4

L3

L2

L1

WHT

SSR 1

1 P

3 2

1 J3

2

SW2O.T. SW

N.O.

N.C.1

P4

2

1 J4

2

RED

RED

BLK

BLK

AT0A-2758-1

1 P5 2

1 J5 2

WHT

1 2 3 4 5 6 7J2

1 2 3 4 5 6 7P1

P21 2 3 4 5 6 7

WH

T

RE

D

OR

N

RED

BLK WHT

ORN

GRNBLU

WHT/BLK

WH

T

GR

N

CONTROL PANEL

BLK CONTACTOR

ENCLOSURE

AT2A-2764-1

AT2A-2760-5

AT0A-2761-1

YEL

RED

J11 2 3 4 5 6 7

ON/OFFSW1 PWR

LT1HEATLT2

BLK

RED

WHT

ORN

YE

L

CONTROL PANEL

AT0E-1800-1 AT0E-1800-2

AT2A-2762-2

BLU BLU

PRTD

RED RED

WHT

OR

N



to

ANALOG CONTROLER

R1 R3R2

1

4

2

3

L3

L1

L2

BLK

5

6WHT

N

MODEL EGD DROP-IN 240V SINGLE PHASE SSR HEATER CONFIGURATIONAT2T-2713-9


24 208 13.52

24 240 18

36 & 48 208 9.11

36 & 48 240 12.13



AccuTemp Products, Inc. ( AccuTemp ) warrants that your AccuTemp equipment will be free of defects in material andworkmanship under normal use for a period of twelve (12) months from installation or fifteen (15) months from date of shipmentfrom AccuTemp, whichever date first occurs (the Warranty Period ). Registration of AccuTemp equipment is required at timeof installation.

Damage to AccuTemp equipment that occurs during shipment must be reported to the carrier, and is not covered under this warranty.The reporting of any damage during shipment is the sole responsibility of the commercial purchaser/user of such AccuTempequipment.

AccuTemp provides an active service department, which should be contacted and advised of service issues regardless of warrantyperiod.

During the warranty period, AccuTemp agrees to repair or replace, at its option, F.O.B. factory, any part which proves to be defectivedue to defects in material or workmanship, provided the equipment has not been altered in any way and has been properly installed,maintained, and operated in accordance with the instructions in the AccuTemp Owners Manual.

During the warranty period, AccuTemp also agrees to pay for any factory authorized equipment service agency (within the continentalUnited States and Canada) for reasonable labor required to repair or replace, at our option, F.O.B. factory, any part which proves tobe defective due to defects in materials or workmanship, provided the service agency has received advance approval from AccuTempfactory service to perform the repair or replacement. This warranty includes travel time not to exceed two hours and mileage not toexceed 50 miles (100 miles round trip), but does not include post start-up assistance or training, tightening of loose fittings or externalelectrical connections, minor adjustments, maintenance, or cleaning. AccuTemp will not reimburse the expense of labor requiredto replace parts after the expiration of the warranty period.

Proper installation is the responsibility of the dealer, owner-user, or installing contractor and is not covered by this warranty. WhileAccuTemp products are built to comply with applicable standards for manufacturers, including Underwriters Laboratories (UL) andNational Sanitation Foundation (NSF), it is the responsibility of the owner and the installer to comply with any applicable local codesthat may exist.

AccuTemp makes no other warranties or guarantees, whether expressed or implied, including any warranties of performance,merchantability, or fitness for any particular purpose. AccuTemp s liability on any claim of any kind, including negligence, withrespect to the goods and services covered hereunder, shall in no case exceed the price of the goods and services, or parts thereof,which gives rise to the claim. In no event shall AccuTemp be liable for special, incidental, or consequential damages, or damages inthe nature of penalties.

This constitutes the entire warranty, which supersedes and excludes all other warranties, whether written, oral, or implied.

IMPORTANTImproper installation can affect your warranty. Installation is the responsibility of the Dealer, Owner/User or the Installation Contractor.See: Section One, Installation of the Owner s Manual.

For Service Call 800-480-0415

Call 800 210-5907

Product Warranty

U.S. & Canada Sales Only

LIMITED WARRANTYOne Year Parts and Labor

MM6311-0601


INFORMATION

IMPORTANT SERVICE INFORMATIONAccuTemp Product, Inc. Technical & Customer Support Technician is

available Monday thru Sunday, 7:00am to 7:00pm EST

800 480-0415 or 260 469-3040

• Phone - 800 480-0415 or 260 469-3040• Fax - 260 469-3045• Email - [email protected]• Web site - www.accutemp.net

electric griddle installation & owners … griddle installation & owners manual serial...

Documents