echlin digital fuel injector belden flow bench and ......bosch k-jet various types page bosch...

BeldenEchlin Digital Fuel Injector Flow Bench and Ultrasonic

Cleaning System

Copyright 2009 ASNU Corporation All Rights Reserved

IMPORTANT

Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used

only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced.

Match & select the components with the injector. Ensuring they are suitable for use.

IMPORTANT - INJECTOR SERVICE INFORMATION

QUALIFY THE INJECTORS TO BE SERVICED BY PART NUMBER AND APPLICATION.

CORROSION OR RUST CONTAMINATION IN INJECTOR INLET CANNOT BE PROPERLY

CLEANED. CLEANING INJECTOR WILL NOT RESOLVE PROBLEM AND INJECTORS MUST BE

REPLACED.

INJECTORS WITH BROKEN OR DAMAGED PINTLE TIPS CANNOT BE REPAIRED.

INJECTORS MUST BE REPLACED.

BEFORE DISASSEMBLING THE INJECTOR, MAKE SURE YOU HAVE THE NECESSARY REPAIR

COMPONENTS. SOME INJECTOR COMPONENTS CANNOT BE REPLACED OR ARE NOT

AVAILABLE FROM ASNU. REFER TO THE INJECTOR INDEX.

ADAPTER APPLICATIONS: WE ARE NOT ABLE TO IDENTIFY EVERY APPLICATION THIS IS

ONLY A GUIDE, PLEASE REPER TO PAGES TO THE INJECTOR INDEX.

ACCESSORY INFORMATION: REFER TO PAGES

FOR THE BEST PERFORMANCE, CLEANED INJECTORS SHOULD BE INSTALLED IN VEHICLE

IMMEDIATELY AFTER SERVICING WITH ASNU.

SHELF LIFE: SERVICED INJECTORS THAT WILL NOT BE RE-INSTALLED TO A VEHICLE

ENGINE MUST BE TREATED WITH AN INHIBITER AND FITTED WITH EITHER 2-15110 OR

2-15114 DUST PROTECTION CAPS. FAILURE TO FOLLOW RECOMENDATIONS COULD

RESULT IN SEIZURE OF INTERNAL COMPONENTS.

REFER TO ASNU OPERATION MANUAL FOR PROPER PROCEDURE.

DUST PROTECTION CAPS MUST BE INSTALLED TO PREVENT CONTAMINATION & PRE-

SURVE INJECTOR SHELF LIFE. SEE INJECTOR INDEX TO SELECT PROPER

PROTECTIVE CAPS.

Page Page Page 222


IMPORTANT




Machine Warranty

Page Page Page 333

All repairs or replacements of machines will be handled NAPA Echlin DSM. All questions regarding inoperative machines will be conducted through your local NAPA Echlin DSM.

If a machine breaks down and repairs cannot be determined in the field, the NAPA Echlin DSM will get authorization to ship the machine back to the factory for repairs or replacement for up to one year after purchase. The customer will be instructed where to ship the machine prepaid and then all freight charges will be re-reimbursed.

If the customer is able to determine the problem causing an inoperative machine, upon approval of the NAPA Echlin DSM, the necessary parts will be shipped on a no charge basis for up to one year after purchase. The customer will perform the replacement of these parts. No labor will be paid for customer installed components.

In instances where the machine has been damaged due to user neglect, we will ship parts for a charge, plus freight. If repairs are done at the ASNU repair center, all freight, parts and labor are the responsibility of the user.

After the 12 month warranty period, the user may continue to have the machine serviced at the ASNU Repair Center, on a labor, materials and freight cost basis.

The ASNU Repair Center will not be responsible for any damage which occurs during the shipment of a machine back to the user.


IMPORTANT




BOSCH

Various

Page

ROCHESTER

GM MULTEC

Page

LUCAS

DISC

Page

WEBER

MPI

Page

DENSO

Ford/Mazda/Kia

Page

HONDA

KEIHIN STYLE

Page

BOSCH

Various

Page

DELPHI

Page

Machine Warranty

Section 1 Page Section 1 Page Section 1 Page Section 1 Page 1111


IMPORTANT




Injector Index

BOSCH

Page

BOSCH D-JET

Page

BOSCH

Trumpet Cap Type

Page

BOSCH

Ford/Mazda

Page

BOSCH D-JET

Page

BOSCH K-JET

Various Types

Page

BOSCH

Toyota/Mitsubushi

Page

DENSO

Chrysler/Mitsubishi

Page

JECS

Nissan

Page

BOSCH

Chrysler

Page

BOSCH

Ford CFI

Page

SIEMENS GDI

Citroen/Peugeot

Page

Page Page Page Page 2222

IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used




IMPORTANT




Injector Index

HITACHI GDI

Mitsubushi

Page

BOSCH GDI

VW

Page

BOSCH GDI

Ford

Page

BOSCH

Ford

Page

WEBER

Fiat/PSA

Page

SIEMENS

VW/Audi

Page

SIEMENS

VW/Audi

Page

BOSCH

Ford

Page

SIEMENS

Chysler

Page

SAGEM AIR ASSISTED

BMW/KIIA

Page 40



IMPORTANT




Injector Index

ROCHESTER/WEBER

Page

ROCHESTER/WEBER

Page

BOSCH / HOLLY

Page

DENSO

Nissan /Subaru

Page

BOSCH

Chrysler

Page

BOSCH/WEBER

DENSO/SIEMENS

Page

JECS

Nissan/Toyota

Page

JECS

Nissan

Page

JECS

Toyota

Page

JECS

Nissan

Page

DENSO

Mazda

Page

DENSO

Nissan

Page



IMPORTANT




Injector Index

KEIHIN

Honda

Page

KEIHIN

Honda

Page

BOSCH

Ford

Page

BOSCH

Nissan

Page

BOSCH

Chrysler

Page

DENSO

Susuki

Page

GM EARLY VORTEC SYSTEMS

Page

GM LATE VORTEC SYSTEMS

Page

GM LATE VORTEC SYSTEMS

Page



IMPORTANT




GM / BMW

MERCEDES

(16V & 24V ENGINES)

BOSCH

MULTI HOLE TYPE

2-15536 with filter in.

2-15001

FILTER

2-15004

O-RING-BROWN

TOP & BOTTOM

2-15114

DUST CAP

2-15662

SPACER-1mm

2-15038

PINTLE CAP

MULTIHOLE 3mm

HOLE

2-15012

SPACER 2mm

2-15671

PINTLE CAP

MULTIHOLE

OPEN ENDED

2-15663

PINTLE CAP

FOR BMW

3mm HOLE

2-15035

PINTLE CAP

3mm HOLE

2-15511

Test Adapter for

injectors with

filter removed

2-15536

Test Adapter for

injectors with

filter installed

2-15502

Universal Injector

Wire Harness

Top Feed Injectors

Section 3 Page 1Section 3 Page 1Section 3 Page 1Section 3 Page 1


IMPORTANT




GM

ROCHESTER MULTEC

Use Adapter 2-15536

with filter in.

2-15001

FILTER

2-15004

O-RING-BROWN

TOP & BOTTOM

2-15114

CAP (2 REQ)

2-15109

SPACER

2-15511

Test Adapter for

injectors with

filter removed

2-15536

Test Adapter for

injectors with

filter installed

2-15502

Universal Injector

Wire Harness

Top Feed Injectors



IMPORTANT




Warning

Use only ASNU

02 with these

Injectors

ROVER / BMW

SAAB / PSA

LUCAS IDISC

Use Test Adapter


2-15013

O-RING

TOP AND BOTTOM

NA

FILTER

2-15110

CAP (2 REQ)

2-15511

Test Adapter for

injectors with

filter removed

2-15536

Test Adapter for

injectors with

filter installed

2-15502

Universal Injector

Wire Harness

Top Feed Injectors



IMPORTANT




FORD / FIAT

PSA (EUROPE)

Weber

Use Test Adapter


NA

FILTER

NA

PINTLE CAP

2-15012

SPACER

2-15004

O-RING

2-15114

CAP (2 REQ)

2-15511

Test Adapter for

injectors with

filter removed

2-15536

Test Adapter for

injectors with

filter installed

2-15502

Universal Injector

Wire Harness

Top Feed Injectors



IMPORTANT




FORD / FIAT

PSA (EUROPE)

Weber

Use Test Adapter


2-15001

FILTER

2-15019

PINTLE CAP

2-15009

O-RING

2-15007

DUST SEAL

2-15114

DUST CAP

2-15008

HEAD SEAL

2-15110

DUST CAP

2-15511

Test Adapter for

injectors with

filter removed

Test Adapter 2-15538

test injectors with

filter installed

2-15502

Universal Injector

Wire Harness

Top Feed Injectors



IMPORTANT




HONDA

KEIHIN STYLE

Use Test Adapter


2-15014

GREEN SEAL

2-15015

O-RING

2-15041

HEAD SEAL

PINTLE CAP CANNOT BE REPLACED. DO NOT REMOVE

FOR INJECTOR CLEANING OR TESTING

2-15016

GROMMET

2-15064

FILTER

2-15114

CAP

2-15110

CAP

2-15511

Test Adapter for

injectors with

filter removed

2-15538

Test Adapter for

injectors with

filter installed

2-15502

Universal Injector

Wire Harness

Top Feed Injectors



IMPORTANT




VARIOUS

VEHICLES

BOSCH EV6

MULTIPOINT

Use Test Adapter

2-15538

use Adapter 2-15640

plate in fuel rail for testing

2-15013

O-RING

(TOP & BOTTOM)

2-15001

FILTER

USE 2-15640 - INJECTOR MOUNTING PLATE IN

FUEL RAIL TO HOLD INJECTORS

PLASTIC O'RING RETAINING WASHER NOT YET

AVAILABLE, REMOVE CAREFULLY AND RE-USE OLD WASHER

2-15511

Test Adapter for

injectors with

filter removed

2-15536

Test Adapter for

injectors with

filter installed

2-15502

Universal Injector

Wire Harness

Top Feed Injectors



IMPORTANT




Top Feed Injectors


BUICK Delphi production

Use Injector Adapter 2-15536

Use custom harness 2-15637

2- O-RING (LOWER)

2- O-RING (UPPER)

2-15001 FILTER

USE ASNU 89 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS

PINTLE CAP NOT YET AVAILABLE DO NOT REMOVE

INJECTOR ADAPTER 2-15536

(Tests Injectors with filter installed)

DELPHI WIRING HARNESS 2-15637


IMPORTANT




GM / JAGUAR FIAT-ALFA

Use Adapter 2-15537 with hose and filter

installed

2-15020 PINTLE CAP

2-15019 PINTLE CAP

2-15006 O-RING

2-15001 FILTER

2-15110 CAP

2-15114 CAP

2-15010 O-RING

2-15024 FERRULE

2-15011 SEAL

2-15511 Test Adapter for injectors with filter removed

2-15537 Tests injectors with hose

& filter installed

2-15502 Universal Injector Wire Harness

Top Feed Injectors



IMPORTANT




MERCEDES JAGUAR / VOLVO

BOSCH D-JETRONIC Use Adapter 2-15537 with hose installed Use Adapter 2-15511

without hose and filter installed

Connect Injectors with 2-15502

Universal Harness

2-15019 PINTLE CAP

2-15001 FILTER

2-15006 O-RING

2-15011 SEAL

2-15110 CAP

2-15114 CAP

2-15006 HEAD SEAL

2-15024 FERRULE

2-15511

(ASNU 51) Test Adapter for injectors with filter removed

2-15537

(ASNU 58) Tests injectors with hose

& filter installed

2-15502

(ASNU 70) Universal Injector Wire Harness

Top Feed Injectors



IMPORTANT




Top Feed Injectors


GM / SAAB Chimney Style

Aliminium Pintle Cap 2-15536 with filter in

Replacement cap not available, remove and replace

with 2-15672

2-15012 WASHER

ASNU 14 O-RING (2 REQ)

2-15001 FILTER

2-15017 PLASTIC PINTLE CAP RENAULT CLIO ONLY

ASNU 23 BOTTOM O'RING RENAULT

CLIO ONLY

2-15110 CAP

2-15114 CAP


2-15536 Tests injectors with hose &

filter installed



IMPORTANT




Top Feed Injectors


FORD / HYUNDAI MAZDA / PROTON Pintle type with

SINGLE SPRAY exit hole. For Multi Hole Spray

See page 25

Use Test Adapter 2-15538 with filter in

2-15096 PINTLE CAP BLACK - 10 DEG



2-15099 PINTLE CAP

2-15067 PINTLE CAP

2-15070 PINTLE CAP 18 SPRAYS

2-15001 FILTER

2-15110 CAP

2-15114 CAP

2-15007 bushing

2-15009 O'RING

2-15102 O'RING

2-15008 HEAD SEAL


2-15538 Tests injectors with filter in-

stalled



IMPORTANT




Top Feed Injectors


CADILLAC Use Test Adapter 2-15511

Connect Injectors with 2-15502 Universal Harness

2-15019 PINTLE CAP

ASNU 240 COPPER WASHER

2-15001 FILTER

2-15110 CAP

2-15107 BLEEDER O-RING

2-15006 HEAD SEAL

2-15302 O-RING


tests injectors with hose & filter removed

2015502 Universal Injector Wire Harness


IMPORTANT




Top Feed Injectors


K-JETRONIC BOSCH MECHANICAL FUEL INJECTOR &

COLD START VALVES

Use Adapter 2-15535 or 2-15514 or 2-15515

2-15002 O-RING

2-15109 0-RING

AUDI APPLICATIONS

2-15114 CAP

2-15110 CAP

2-15108 MOUNTING SEAL

VARIOUS

2-15101 MOUNTING SEAL

BMW

Test Adapter 2-15535 10mm Female Coupling For Male K-Jet & Cold Start

Test Adapter 2-15514 8mm Male

Coupling for Female K-Jet & Cold Start

Test Adapter 2-15515 12mm Female Coupling

for Male K-Jet


IMPORTANT




Top Feed Injectors


MAZDA Use Test Adapter

2-15538 with filter in

2-15009 O-RING

2-15008 HEAD SEAL

2-15106 BUSHING

2-15019 PINTLE CAP

2-15001 FILTER

2-15110 CAP

2-15114 CAP

Test Adapter 2-15511 test s injectors with filter removed

Test Adapter 2-15538 tests injectors with filter

installed



IMPORTANT




Top Feed Injectors


TOYOTA MAZDA Use test Adapter

2-15538 with filter in

2-15009 O-RING

2-15008 HEAD SEAL

2-15007 DUST SEAL

ASNU 241 O-RING

2-15055 SEALING O-RING

ASNU 243 HOUSING SEAL

2-15062 HOUSING RING

2-15001 FILTER

2-15021 PINTLE CAP

2-15019 PINTLE CAP

2-15110 DUST CAP

2-15114 DUST CAP

Test Adapter 2-15511 tests injectors with filter

removed

Test Adapter 2-15538 tests injectors with

filter installed



IMPORTANT




Top Feed Injectors


CHRYSLER NISSAN


Connect Injectors w/ 2-15502 Universal Harness

2-15009 O-RING

2-15033 COLLAR

2-15094 INSULATOR SEAL

2-15110 DUST CAP

2-15114 DUST CAP

Test Adapter 2-15511tests injectors with filter removed

Test Adapter 2-15538 tests injectors with filter installed



IMPORTANT




Top Feed Injectors


NISSAN Use Test Adapter 2-15538

with filter in Connect injectors w/ 2-15502

Universal Harness

2-15001 FILTER

2-15019

PINTLE CAP

2-15006 O-RING

2-15009 O-RING

2-15051 BUSHING

2-15110 DUST CAP

2-15114

DUST CAP


2-15538 Test Adapter for injectors with filter installed



IMPORTANT




Top Feed Injectors


CHRYSLER TBI

SINGLE UNIT

Use Test Adapter 2-15536

with filter in

2-15001 FILTER

2-15110 DUST CAP BOTTOM

2-15114 DUST CAP TOP

2-15004 TOP O-RING

2-15011 BODY CLAMPING SEAL

ASNU 273 LOWER BODY O'RING SEAL

2-15536 INJECTOR ADAPTER

Tests injectors with filter installed



IMPORTANT




Top Feed Injectors


FORD CFI DUAL UNIT


2-15501 FILTER

2-15312 FILTER CFI

2-15068 PINTLE CAP

2-15069 PINTLE CAP

2-15304 LOWER O-RING

2-15302 UPPER O-RING

2-15114 DUST CAP TOP

2-15110 DUST CAP BOTTOM

2-15511 INJECTOR ADAPTER

Tests injectors with filter removed



IMPORTANT




Top Feed Injectors


CITROEN PEUGEOT- GDI

SIEMENS Gasoline Direct Injection

Use Test Adapter ASNU 56 with filter in

ASNU 262 O-RING (TOP)

ASNU 264 FILTER

ASNU 263 SPLIT SPACER

ASNU 265 NYLON SEALING BUSH

INJECTOR ADAPTER ASNU 56

Tests injectors with filter installed

WIRING HARNESS 2-15502

Universal Injector


IMPORTANT




Top Feed Injectors


MITSUBUSHI HITACHI - GDI

Gasoline Direct Injection Use Test Adapter 2-15536

with filter in

TO TEST: REMOVE TOP O'RING & SPLIT WASHER.

REPLACE WITH 2 x 2-15004 & USE 2-15536 COUPLING

ASNU 234 O-RING

ASNU 20 FILTER


Test injectors with filter installed


Universal Injector


IMPORTANT




Top Feed Injectors


FORD - GDI BOSCH


with filter in


2-15001 FILTER


INJECTOR ADAPTER 2-15536 (Tests injectors with filter installed)


Universal Injector


IMPORTANT




Top Feed Injectors


VW - GDI Bosch


with filter in

ASNU 14 0-RING (TOP & BOTTOM)

2-15001 FILTER


INJECTOR ADAPTER 2-15536 (Tests injectors with filter installed)


Universal Injector


IMPORTANT




Top Feed Injectors


FORD - USA BOSCH


Use 2-15640 Adapter Plate in fuel rail for testing

ASNU 14 BOTTOM O-RING

2-15001 FILTER

USE 2-15640 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS

ASNU 239 BOTTOM 0-RING

Test Adapter 2-15511 tests injectors with hose & filter removed


(Tests injectors with filter installed)


Universal Injector


IMPORTANT




Top Feed Injectors


CITROEN PEUGEOT RENAULT

FIAT Weber & Siemens

Use Test Adapter 2-15536 with filter in Use 2-15640 Adapter Plate in fuel rail for

testing

ASNU 14 O-RING (TOP & BOTTOM)

ASNU 04 FILTER

USE 2-15640 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS

Test Adapter 2-15511 tests injectors with hose & filter re-

moved




Universal Injector


IMPORTANT




Top Feed Injectors


VW / AUDI SIEMENS



ASNU 03 FILTER

PINTLE CAPS ARE NOT REMOVABLE





Universal Injector


IMPORTANT




Top Feed Injectors


VW / AUDI SIEMENS

Use Test 2-15536 with filter in


2-15001 FILTER





WIRING HANESS 2-15502

Universal Injector


IMPORTANT




Top Feed Injectors


FORD USA SIEMENS



2-15001 FILTER





Universal Injector


IMPORTANT




Top Feed Injectors


CHRYSLER USA

SIEMENS Use Test Adapter 2-15536

with filter in


2-15001 FILTER





Universal Injector


IMPORTANT




Top Feed Injectors


BMW / KIA Air Assisted

Sagem Use Tests Adapter 2-15536

with filter in


2-15001 FILTER


ASNU 21 O-RING (BOTTOM)




Universal Injector


IMPORTANT




Side Feed Injectors


WEBER / ROCHESTER LARGE

MONO POINT / SINGLE POINT TBI (USA)

Use Test Adapter 2-15518(single injector block

includes custom harness) or

Use Test Adapter 2-15598 (twin injector block includes

custom harness)

2-15110 DUST CAP

2-15031 SIDE FEED FILTER

ASNU 60F HOUSING WASHER

ASNU 60C WEBER FILTER

2-15301 ROCHESTER FILTER

2-15320 HOUSING O-RING

ASNU 60B WEBER BOTTOM O-RING

2-15319 ROCHESTER BOTTOM O-RING

ASNU 60J DUST SEAL

2-15518 ADAPTER BLOCK

2-15598 ADAPTER BLOCK


IMPORTANT




Side Feed Injectors

VARIOUS APPLICATIONS

WEBER / ROCHESTER SMALL

MONO POINT / SINGLE POINT

TBI (USA)

Use Test Adapter 2-15519 (single

injector block includes custom

harness) or Use Test Adapter 2-15632 4

injector block (includes custom har-

ness)

2-15110

CAP

2-15307

O-RING (ROCHESTER)

2-15093

WEBER FILTER

ASNU 64F

ROCHESTER FLTER

ASNU 64C

WEBER FILTER

ASNU 64E

ROCHESTER FILTER

ASNU 64B

O-RING

2-15519

ADAPTER BLOCK

2-15632

ADAPTER BLOCK & HARNESS

GM TBI MULTEC 700



IMPORTANT




Side Feed Injectors

CHRYSLER

CFI

SINGLE UNIT

BOSCH

(LONG VERSION)

Use Test Adapter 2-15597 (single block)

or

Test Adapter 2-15528(twin block)

2-15065

FILTER

2-15321

O-RING (LOWER)

2-15669

2-15528

(twin block w/harness)

2-15597

(single block w/harness)



IMPORTANT




Side Feed Injectors

NISSAN / SUBARU

SINGLE POINT


(single block)

MULTI POINT

Use Adapter

2-15608 (6 inj. block)

Connect injectors with universal

harness 2-15502

2-15077

FILTER

2-15019

PINTLE CAP

2-15048

SEAL

(Nissan)

2-15049

PLASTIC WASHER

2-15673

O-RING

2-15635

CAP

2-15674

LOWER O-RING

2-15523

SINGLE BLOCK

Use 2-15608

4 INJ. BLOCK

2-15608

6 INJ. BLOCK



IMPORTANT




Side Feed Injectors


BOSCH

MONOPOINT / SINGLE POINT

TBI (USA)


(single block includes custom

harness)

2-15032

O-RING (UPPER)

2-15043

O-RING (LOWER)

2-15066

CLIP (UPPER)

2-15672

FILTER (NEW TYPE) (UPPER)

2-15065

FILTER (UPPER)

2-15093

FILTER (LOWER)

2-15524

ADAPTER BLOCK WITH CUSTOM

HARNESS

2-15110

DUST CAP

2-15671

PINTLE CAP



IMPORTANT




Side Feed Injectors


BOSCH, WEBER, DENSO,

SIEMENS

Use Test Adapter 2-15530 (block

holds 4 injectors)

or


(block holds 6 injectors for

Chrysler 3.5L)


harness 2-15502

2-15032

O-RING TOP

2-15679

O-RING BOTTOM

2-15065

FILTER

WEBER & SIEMENS INJECTORS

HAVE NO REMOVABLE

PINTLE CAPS

2-15659

SINGLE SPRAY PINTLE CAP

BOSCH

2-15070

TWIN SPRAY

PINTLE CAP

DENSO

2-15530

ADAPTER BLOCK

(Holds 4 injectors - Ford Zeta

2-15635

ADAPTER BLOCK

(Holds 6 injectors - Jaguar &

Chrysler 3.5L)



IMPORTANT




NISSAN

&

TOYOTA


(block holds 2 injectors,

includes custom harness)

2-15682

O-RING (UPPER)

2-15114

CAP

2-15612

O-RING (LOWER)

ASNU 102C

FILTER

2-15607

ADAPTER BLOCK

Side Feed Injectors



IMPORTANT




Side Feed Injectors

NISSAN JECS


(block holds 6 injectors)

Connect injectors with

universal harness 2-15502

2-15039

TOP O-RING

2-15613

BOTTOM O-RING NISSAN

2-15685

BOTTOM O-RING TOYOTA

2-15053

TOP O-RING Nissan / Toyota Housing

seal (large)

2-15050

TOP O-RING Nissan /

Toyota Housing seal (small)

2-15052

TOP O-RING Nissan / Toyota

Housing seal (medium)

ASNU 103C

FILTER

ASNU 103E

PINTLE CAP

2-15685

FILTER / SPACER

2-15609

ADAPTER BLOCK

2-15613

BLANKING OFF PLUG

2-15110

DUST CAP



IMPORTANT




Side Feed Injectors

TOYOTA JECS




harness 2-15502

2-15058

O-RING

2-

15060

O-RING

2-15687

O-RING

REPLACEMENT FILTER

CURRENTLY NOT

AVAILABLE DO NOT REMOVE

FILTER

2-15059

INSULATOR

2-15110

CAP

2-15606

TWIN ADAPTER BLOCK

2-15502

UNIVERSAL INJECTOR

WIRE HARNESS



IMPORTANT




Side Feed Injectors

NISSAN

JECS



Connect injectors with

universal harness 2-15502

2-15029

O-RING (UPPER)

2-15689

O-RING (LOWER)

REPLACEMENT FILTER NOT CURRENTLY

AVAILABLE DO NOT REMOVE FILTER

2-15114

CAP

2-15529

ADAPTER BLOCK

2-15502

UNIVERSAL INJECTOR WITH HARNESS



IMPORTANT




Side Feed Injectors

MAZDA

NIPPON DENSO


(Injector block)


harness 2-15502

2-15690

TOP O-RING

2-15004

BOTTOM O-RING

REPLACEMENT FILTER CURRENTLY

NOT AVAILABLE DO NOT REMOVE

FILTER

2-15659

SINGLE SPRAY PINTLE

CAP BOSCH 2-15070

TWIN SPRAY PINTLE CAP

DENSO

2-15634

6 INJ. BLOCK

2-15613

BLANKING OFF PLUG



IMPORTANT




Side Feed Injectors

NISSAN

JECS


(4 Injector block)


harness 2-15502

2-15692

TOP O-RING

2-15693

BOTTOM O-RING

REPLACEMENT FILTER CURRENTLY NOT

AVAILABLE DO NOT REMOVE FILTER

2-15661

4 INJ. BLOCK

2-15502

UNIVERSAL INJECTOR WIRE HARNESS



IMPORTANT




Side Feed Injectors

HONDA CIVIC

KEIHIN


(double block)

Connect injectors with universal harness

2-15502

2-15029

TOP O-RING

2-15030

MIDDLE O-RING

2-15040

UPPER SEAL

2-15110

CAP

2-15636

TWIN ADAPTER BLOCK

2-15502

UNIVERSAL INJECTOR WIRE

HARNESS



IMPORTANT




Side Feed Injectors

HONDA CIVIC

KEIHIN


(double block)

Connect injectors with universal harness

2-15502

2-15029

TOP O-RING

2-15030

MIDDLE O-RING

2-15036

BOTTOM O-RING

2-15040

UPPER SEAL

2-15110

CAP

2-15636

TWIN ADAPTER BLOCK

2-15502

UNIVERSAL INJECTOR WIRE

HARNESS



IMPORTANT




Side Feed Injectors

FORD CFI

SINGLE UNIT

BOSCH


(single block) or

Test Adapter 2-15528 (block)

2-15309

O-RING (LOWER)

2-15314

O-RING (UPPER)

ASNU 61C

FILTER

2-15597

ADAPTER BLOCK

(Includes Custom Harness)

2-15528

ADAPTER BLOCK

(Includes Custom Harness)



IMPORTANT




Side Feed Injectors

NISSAN CFI

SINGLE UNIT

BOSCH

Use Test Adapter 2 2-15597

(single block) or

Test Adapter 2-15528 (twin block)

2-15322

O-RING (UPPER)

2-15306

FILTER

2-15321

O-RING (LOWER)

2-15597

(single block w/harness)

2-15528

(twin block w/harness)

2222----15669156691566915669 CUPCUPCUPCUP (Bosch Style Only)(Bosch Style Only)(Bosch Style Only)(Bosch Style Only)



IMPORTANT




Side Feed Injectors

CHRYSLER

CFI

SINGLE UNIT

BOSCH

(LONG VERSION) 2-15597

(single block)

or


(twin block)

2-15065

FILTER

2-15322 O-RING (UPPER)

2-15321 O-RING (LOWER)

2-15669

2-15597 (single block w/harness)

2-15528 (twin block w/harness)

2222----15669156691566915669 CUPCUPCUPCUP (Bosch Style Only)(Bosch Style Only)(Bosch Style Only)(Bosch Style Only)



IMPORTANT




Side Feed Injectors

SUZUKI

MONOPOINT

DENSO


(single block)

2-15027

O-RING

2-15026

O-RING

REPLACEMENT FILTER CURRENTLY

NOT AVAILABLE DO NOT REMOVE

FILTER

2-15114

DUST CAP

2-15525

ADAPTER BLOCK WITH CUSTOM HARNESS



IMPORTANT




Vortec Injectors

Use Test Adapter 2-15631 (tests &

cleans complete assembly )

Connect injectors with 2-15629

Universal Harness

GM VORTEC

4.3L V-6 & 5.7L CPI

SPRAYING SECURING FLOWING

2-15631 Test Adapter Kit

Includes plastic cleaning tray (see below) for ultrasonic cleaning of individual

injector coils & frame mount shown below.

Injector components not available at this time

2-15631

Test Adapter Stainless Steel

Frame in Anodized Aluminum

Rail Complete with cleaning

tray

2-15660

Cleaning Tray

2-15629

Vortec Harness



IMPORTANT




GM VORTEC

4.3L V-6 CPI

MODELS 92-95


(tests complete assembly)

ASNU 108A

O-RING Early style GM Vor-

tex 4.3L

ASNU 108B


tex 4.3L

ASNU 108C

O-RING Early style GM

Vortex 4.3L

ASNU 108D


tex 4.3L

ASNU 108E

O-RING Early style GM

Vortex 4.3L

2-15630

Test Adapter Kit

ASNU 108T

Cleaning Tray

(optional)

Vortec Injectors



IMPORTANT




Accessories, Components and Adaptors

2-15627

BIO-CLEAN ULTRASONIC CLEANING FLUID

5 LITER BOTTLE

2-15593

FLOW-RITE

CALIBRATION FLUID

5 LITER BOTTLE

ASNU 46

ADAPTER COUPLING HITACHI INJECTORS

USED ON AUDI QUATTRO

2-15532

8MM FEMALE ADAPTER COUPLING FOR

8MM MALE COLD START INJECTOR

2-15533

10MM MALE ADAPTER COUPLING

FOR 10MM FEMALE COLD START

INJECTOR

2-15534

ADAPTER COUPLING COLD START

INJECTOR HOSE TYPE (12-13MM)

2-15535

10MM FEMALE ADAPTER COUPLING

FOR 10MM MALE COLD START

INJECTOR

2-15511

ADAPTER COUPLING TOP FEED MULTI-

PORT INJECTORS WITH FILTER

BASKET REMOVED

2-15512

SMALL O-RING FOR 2-15511 COUPLING



IMPORTANT




2-15513

LARGE (TOP) O-RING FOR ASNU ADAPTER

COUPLING

2-15514

8MM MALE ADAPTER COUPLING FOR 10MM

FEMALE CIS (K-JET)

2-15515

12MM FEMALE ADAPTER COUPLING

FOR 12MM MALE CIS (K-JET)

ASNU 56

ADAPTER COUPLING FOR SLIM TOP

SIEMENS GDI INJECTORS TESTS INJEC-

TORS WITHOUT REMOVING INLET FILTER

2-15536

ADAPTER COUPLING BOSCH, LUCAS,

WEBER, MARELLI, SIEMENS TESTS

INJECTORS WITHOUT REMOVING INLET

FILTER

2-15537

ADAPTER COUPLING TESTS

MULTIPORT INJECTORS WITH FUEL

HOSE INSTALLED

2-15538

ADAPTER COUPLING SLIM TYPE DENSO

TESTS INJECTORS WITHOUT REMOVING

INLET FILTER

2-15502

UNIVERSAL INJECTOR HARNESS

CONNECTS MOST MULTIPORT INJECTORS

2-15610

REPAIR KIT FOR MAIN ASNU

INJECTOR HARNESS

NOT AVAILABLE




IMPORTANT




2-15518

ADAPTER BLOCK

GM TBI MAXI WITH CUSTOM HARNESS

(single block - use 2-15598 for double

block)

2-15519

ADAPTER BLOCK

GM TBI MULTEC WITH CUSTOM HARNESS

(single block - use 2-15632 for Quad

Block)

2-15526

ADAPTER BLOCK

FORD CFI - HOLLEY SPI CHRYSLER &

BOSCH WITH CUSTOM HARNESS

(single block - use 2-15528 for double

block)

2-15522

ADAPTER KIT

MITSUBISHI MPI WITH CUSTOM HAR-

NESS

(Tests 2 injectors)

2-15529

ADAPTER BLOCK

NISSAN / SUBARU SPI

(Tests 4 injectors)

2-15524

ADAPTER BLOCK

BOSCH SPI

(Tests 1 injector)

2-15525

ADAPTER BLOCK

SUZUKI SPI

(Tests 1 injector)

2-15530

ADAPTER BLOCK

FORD ZETA MPI / SPI

(BOSCH / WEBER / SIEMENS / DENSO)

(Tests 4 injectors)

ADAPTER BLOCK

NISSAN / SUBARU SPI

(Tests 1 injector)

Injector Index



IMPORTANT





FILTER BASKET

REMOVAL TOOL

T-HANDLE TYPE

2-15638

CUSTOM NYLON COVER

FOR ASNU MACHINE

NLA

"FOAMEX"

WEATHERPROOF SIGN

COMPONENT ASSTS

2-15100 / FILTERS & CAPS

2-15200 /O'RINGS-SEALS

2-15300 /MONOPOINT KIT

2-15639

PINTLE CAP & FILTER BASKET

ASSEMBLY TOOL

2-15594

PINTLE CAP

REMOVAL TOOL

GUN TYPE

2-15595

FILTER REMOVAL TOOL

GUN TYPE

2-15510

RUBBER BENCH MAT

2-15521

PLASTIC

RAIL HOLDER

DISCONTINUED DISCONTINUED


FILTER BASKET

REMOVAL TOOL

T-HANDLE TYPE

2-15638

CUSTOM NYLON COVER

FOR ASNU MACHINE

NLA

"FOAMEX"

WEATHERPROOF SIGN

COMPONENT ASSTS

2-15100 / FILTERS & CAPS

2-15200 /O'RINGS-SEALS

2-15300 /MONOPOINT KIT

2-15639

PINTLE CAP & FILTER BASKET

ASSEMBLY TOOL

2-15594

PINTLE CAP

REMOVAL TOOL

GUN TYPE

2-15595

FILTER REMOVAL TOOL

GUN TYPE

2-15510

RUBBER BENCH MAT

2-15521

PLASTIC

RAIL HOLDER


IMPORTANT




2-15640

WEBER / SIEMENS

TOP FEED MULTIPOINT

"MINI PECO INJECTOR"

ADAPTER PLATE

2-15605

INJECTOR SERVICE

REPORT PAD

50 SELF CARBON

(ENGLISH ONLY)

2-15531

TBI ADAPTER RING

USE W/ 2-15507 CRADLE

LARGE TBI INJECTORS

(GM MAXI)

2-15601

TBI ADAPTER RING

USE W/ 2-15507 CRADLE SMALL TBI IN-

JECTORS

GM MULTEC / DAEWOO

2-15520

CIS (K-JET) INJECTOR

CLEANING TRAY

2-15641

SIDE FEED INJECTOR CLEANING

TRAY

(SHALLOW)

ASNU 1992 onward

2-15600

ASNU UPTO 1992 (DEEP)

2-15642

CLEANING TRAY

PECO INJECTOR

2-15598

ADAPTER BLOCK

GM TBI MAXI

(Tests 2 injectors, includes custom harness)

2-15607

ADAPTER BLOCK

NISSAN / TOYOTA 2 WIRE

(Tests 2 injectors, includes blanking off

plug & custom harness




IMPORTANT




Injector Index

2-15609

ADAPTER BLOCK

NISSAN JECS

(Tests 6 injectors)

2-15606

ADAPTER BLOCK

TOYOTA JECS MPI

PREVIA / TARAGO

(Tests 6 injectors)

ASNU 105

ADAPTER BLOCK

NISSAN PATHFINDER / NAVARA

(Tests 4 injectors)

2-15608

ADAPTER BLOCK

NISSAN / SUBARU SPI

(Tests 6 injectors)

2-15634

ADAPTER BLOCK

MAZDA / DENSO

(Tests 6 injectors)

2-15630

ADAPTER GM VORTEC 4.3 EARLY VERSION

(Tests complete assembly)



IMPORTANT




Injector Index

2-15631

ADAPTER KIT GM VORTEC 4.3L & 5.7L LATE VERSION

(Tests complete assembly includes cleaning tray)


Echlin Part Numbers 2-15630 and 2-15631 Adapters comes complete with 2-15629 harness and plastic cleaning tray for ultrasonic cleaning of individual injector coils.

2-15629 Harness assembly is a available separately.

The later GM Vortec (late) system is a Multi Point operation with 6 or 8 individual injectors mounted in the housing, allowing either a simultaneous or sequential injection delivery.

The fuel is pressurized into the injector housing and as the injector is electronically opened, the fuel is pressure fed into a nylon delivery tube. At the end of the tube is a pressure poppet valve. The poppet valve sits in the inlet manifold and can be subject to extremely harsh conditions that may affect the per-formance of the valve. The opening and closing of the poppet valve is controlled by pressure and deter-

mines the fuel distribution, fuel atomization and the fuel delivery to each cylinder. The is therefore very important to examine the performance of this system, both before servicing (to un-derstand the cause of the engine problem) and after, to ensure the cause of the problem had been elimi-

nated and that the system is working properly.

SPRAYING SECURING FLOWING


IMPORTANT




Injector Index

2-15631

ADAPTER KIT GM VORTEC 4.3L & 5.7L LATE VERSION

(Tests complete assembly includes cleaning tray)

2-15635

ADAPTER BLOCK

FORD ZETA / SIEMENS

CHRYSLER 3.5L

(Tests 6 injectors)

2-15636

ADAPTER BLOCK

HONDA CIVIC

NIKI KEIHIN

(Tests 2 injectors



IMPORTANT





2-15637



IMPORTANT







IMPORTANT




Numerical Parts Listing Echlin # DESCRIPTION

2-15001 Standard Injector Filter Basket with Brass Collar

2-15002 K-Jetronic (CIS) Injector O'Ring

2-15003 BMW Finned Pintle Insulator Cap - Yellow

2-15004 Standard L-Jetronic O'Ring - 15mm - Black

2-15006 L-Jetronic / Nissan / GM Injector Head Seal - Medium

2-15007 Nippon Denso Injector Rail Dust Seal (50)

2-15008 O'Ring Toyota Bottom Small Flat

2-15009 Toyota / Mazda / Nippon Denso Top O'Ring Seal

2-15010 D-Jetronic Injector O'Ring Head Seal - Small

2-15011 DUST SEAL OD 27MM ID22MM WIDTH 8MM

2-15012 Bosch L-Jetronic Injector Spacer - 2mm

2-15014 Nikki Injector Head Seal

2-15015 Nikki Injector Top O'Ring

2-15016 Honda Injector Grommet

2-15017 Bosch Trumpet End Pintle Cap

2-15018 Bosch/Nippon Denso Standard Pintle Insulator Cap

2-15019 L-Jetronic Standard Pintle Insulator Cap-Black

2-15020 D-Jetronic Pintle Insulator Cap-Black 18mm

2-15021 CAP, PKG TOYOTA PINTLE

2-15022 24 Compartment tray

2-15024 FERRULE, PKG

2-15026 O-RING, PKG INJECT LOW

2-15027 O-RING, PKG INJECT UPP

2-15029 NA FROM ACE



2-15031 SIDE FEED FILTER, PMAXI TBI INJ

2-15032




IMPORTANT




Numerical Parts Listing 2-15033 COLLAR, PKG INJECTOR

2-15035 Pintle Cap

2-15036 O-RING, PKG AUX INJECT

2-15039 Nissan/Toyota Side Feed Injector - Top- O-Ring

2-15040 SEAL, PKG INJECT UPPER

2-15041 SEAL, PKG INJECTOR

2-15042 CLIP, PKG INJECTOR








2-15055 INSULATOR, PKG TOYOTA




2-15060 O-RING, PKG INJECTOR



2-15064 FILTER, HONDA INJECTOR

2-15065

2-15065 Screen Filter 25pk

2-15066 CLIP, SPI BOSCH

2-15067 CAP, MAZDA PINTLE

2-15068 CAP, FORD LRG PINTLE

2-15069 CAP, FORD SMALL PINTLE

2-15070 CAP, FORD 2HOLE PINTLE



IMPORTANT




Numerical Parts Listing 2-15071 O-RING, TOYOTA

2-15072 CAP, WEBER PINTLE

2-15074 Fuel Injector Pintle Cap

2-15075 SPACER, NISSAN INJECTOR

2-15076

2-15076 Fuel Injector Filter Screen

2-15077 Fuel Injector Filter Screen

2-15091 FUEL INJECTOR HOSE

2-15092 SPACER, ROCH INJECTOR

2-15093 FILTER, TBI INJECT LOW

2-15094 Inj. O-Ring 25pk

2-15095 CAP, PINTLE L-JET

2-15096 VAPOR CAP 2-HOLE

2-15097 CAP, DENSO 2HOLE VAPOR

2-15098 CAP, 2HOLE INSULATOR

2-15099 CAP, FORD INSULATOR

2-15100 Multipoint Fuel Injection Kit 2 - O'Rings, Rubber Seals & Dust Caps.

2-15101 BMW CIS (K-Jetronic) Injector O'Ring

2-15102 Mazda Injector O'Ring - Lower Mazda Injector Head Seal

2-15103 Rail Washer 100pk

2-15104 Mazda Injector O'Ring - Lower Mazda Injector Head Seal

2-15106 Mazda Grommet

2-15107 Mazda Air Bleed Socket O'Ring

2-15108 Cadillac Fuel Rail Grommet

2-15109 Audi CIS (K-Jetronic) Injector Seal

2-15110 Injector Protective Cap - Small

2-15111 Injector Protective Cap Rail Fitted Injector Protective Dust Cap

2-15112 Injector Protective Cap

2-15113 Injector Protective Cap Hose Fitted Injector Protective Dust Cap

2-15114 Injector Protective Cap - Large



IMPORTANT




Numerical Parts Listing

2-15300 Singlepoint/Monopoint Fuel Injection Kit 3 - Fiter Baskets, O'Rings & Seals.

2-15301 Rochester bottom filter basket

2-15302 Ford Injector O'Ring - Upper

2-15304 Ford Injector Mounting - Lower O'Ring

2-15305 Hitachi InjectorO'Ring - Small

2-15306 Hitachi Injector Filter Screen

2-15306 Bosch/Chrysler / Hitachi Tbi Filter Screen

2-15307 Rochester TBI Model 700 Injector O'Ring - Upper

2-15308 Inj. Washer 25pk

2-15309 Holley Tbi Injector O'ring - Lower

2-15310 Nissan Injector O'Ring

2-15311 Rochester TBI Larger Filter Screen (50)

2-15312 Ford Injector Filter Screen

2-15313 Bosch Injector O'Ring BLACK (50)

2-15314 Holley Tbi Upper O'ring

2-15315 Rochester Injector Housing Dust Seal

2-15316

2-15316 Niisan Single Point Injector

2-15317 Injector Body Support Rubber - Thick(SQUARE CORNERS)

2-15318 Bosch Injector O'Ring

2-15319 Rochester TBI Large - Lower O'Ring

2-15320 Rochester/Bendix/Weber small TBI O'Ring - Upper

2-15321 Bosch/Chrysler / Hitachi Tbi O'ring - Lower

2-15322 Bosch/Chrysler / Hitachi Tbi O'ring - Upper

2-15323 Chrysler / Hitachi Injector O'Ring

2-15500 ASNU Ultrasonic Injector Cleaner & Flow Bench

2-15502 Universal Injector Harness - Connects most multiport Injectors

2-15503 Plastic Moulded Flow Display Window

2-15504 Calibration Fluid Tank Cover

2-15506 Power Cord USA - 3metre



IMPORTANT




Numerical Parts Listing 2-15507 Ultrasonic Bath Injector Cradle

2-15508 Steel Braided Fuel Hose Complete with Quick Coupler

2-15509 Glass Measuring Cylinder - MM

2-15510 Rubber Bench Mat

2-15511 Adaptor Coupling Top Feed Multiport Injectors w/filter basker removed

2-15512 Small O-Ring for 2-15511 Coupling

2-15513 Large(TOP) O-Ring for 2-15511 Adaptor Coupling

2-15514 8mm Male Adaptor for 10MM Female CIS (K-Jet)

2-15515 12mm Female Adaptor Coupling for 12MM Male CIS (K-Jet)

2-15518 Adaptor Black GM TBI Maxi with Custom Harness (single block / use 2-15598 for double block)

2-15519 GM TBI Multec w/Custom Harness (single block / use 2-15632 for Quad block)

2-15520 CIS K-Jet Cleaning Tray

2-15521 Plastic Fuel Rail Holder

2-15522 Adaptor Kit Mitsubishi MPI w/Custom Harness(Tests two injectors) ECI Two

2-15523 Adaptor Block Nissan / Subaru SPI (tests 1 injector)

2-15524 Adaptor Block Bosch SPI (tests 1 injector)

2-15525 Adaptor Block Suzuki SPI (tests 1 injector)

2-15526 Adaptor Block Ford CFI - Holly SPI Chrysler & Bosch w/Custom Harness (single block / use 2-15528 for double block)

2-15527 Adaptor Block Bosch / Holly / Nissan / Ford (tests 2 injectors)

2-15528 Adaptor Block Bosch / Holly / Nissan / Ford (tests 2 injectors)

2-15529 Adaptor Block Subaru / Nissan SPI (tests 4 Injectors)

2-15530 adaptor Block Ford Zeta MPI /SPI (Bosch / Weber / Siemens / Denso) (tests 4 injectors)

2-15531 TBI Adaptor Ring - use w/2-15507 Cradle large TBI Injectors (GM Maxi)

2-15532 8mm Female Adaptor For 8mm Male Cold Start Injector

2-15533 10mm Male Adaptor for 10mm Female Cold Start Injector

2-15534 Adaptor Coupling Cold Start Injector Hose Type 12-13MM

2-15535 10mm Female Adaptor Coupling for 10MM Male Cold Start Injector

2-15536 Adaptor Coupling Bosch, Lucas, Weber, Marelli, Siemens - Tests Injector w/o

2-15537 Adaptor Coupling Tests Multiport Injectors with Hose Attached

2-15538 Adzaptor Coupling Slim Tyope Denso - Tests Injectors w/o removing inlet filter



IMPORTANT




Numerical Parts Listing 2-15539 Calibration Fluid In-Line Fuel Filter

2-15540 Calibration Fluid In-Tank Pre-pump Filter

2-15562 Ultrasonic Tank Complete Assembly

2-15593 Flow Rite calibration fluid

2-15594 Pintle Cap Removal Tool - Hand Gun Type

2-15595 Filter Basket Removal Tool - Hand Gun Type

2-15597 Adaptor Block Ford CFI - Holly SPI Chrysler & Bosch w/Custom Harness (single block / use 2-15528 for double block)

2-15598 GM-TBI Large (TBI) Dual Injector Manifold and Harness Kit

2-15599 ASNU Main Board-Service Exchange ($750 Core)

2-15600 Side Feed Injector Cleaning Tray (Deep)

2-15601 TBI Adaptor Ring - use w/2-15507 Cradle Small TBI Injectors (GM Multec / Dae-woo)

2-15602

2-15603 Quick Reference Wall Chart - English

2-15604 Instruction Manual

2-15605 Injector Service Report Pad (50 Pages per Pad)

2-15606 Toyota Tarago/Previa Quad Injector Manifold Kit

2-15607 Nissan / Toyota 2 Wire Dual Injector Manifold and Harness Kit

2-15608 Subaru / Nissan Maxima 6 Injector Manifold Kit

2-15609 Nissan Navara Multipoint Six Injector Manifold Kit

2-15610 Repair Lits for Main Injector Harness

2-15612 Injector Blank - Nissan / Toyota 2 Wire

2-15613 Injector Blank - Nissan Navara Multipoint

2-15627 Bio-Clean Ultrasonic Cleaneing Fluid

2-15629 Universal Injector Harness for Vortec System

2-15629 Wiring Harness for Vortec

2-15630 Adaptor Block GM Vortec 4.3 - Early Version

2-15631 Adaptor Kit GM Vortec - 4.3 & 5.7 Later Version

2-15632 Adaptor Block GM TBI Multec 700 ( tests 4 injectors) includes harness

2-15634 Adaptor Block Mazda / Denso (tests 6 injectors) 2-15635 Adaptor Block Ford Zeta / Siemens Chrysler 3.5 (tests 6 injectors)



IMPORTANT




Numerical Parts Listing 2-15636 Adaptor Block Honda Civic / Nikki Keihen (tests 2 injectors)

2-15637 Custom Harness Delphi Pin Type Connectors (tests up to 8 injectors)

2-15638 Injector Nylon Cover for 2-15500 ASNU Machine

2-15639 Injector Filter Basket & Pintle Cap Assembly Tool

2-15640 Adaptor Plate for Weber / Siemens (Mini Peco Injector)

2-15641 Side Feed Injector Cleaning Tray (Shallow) 1992 onward / 2-15600 up to 1992 (Deep)

2-15642 Perspex cleaning tray for K-jet & Weber/Sieman Mini Peco injectors

2-15643 Magnetically Couples Electric High Performance Pump

2-15644 High Performance Fuel Rail Top Feed Injectors (tests 8 injectors) includes extension bolts for long GDI injectors

2-15645 Lid for ultra-sonic tank

2-15646 GDI injector Drive box

2-15647 Mercury Optimax

2-15648 Filter removal tool replacement bit

2-15649 Late Bosch Pintle



2-15652 Late GM Pencil Pintle

2-15653 Top O-Ring Retainer

2-15654 GM Vortex 4.3L V5 CPI Filter

2-15655 Pintle Cap Holden

2-15656 Pintle Cap Ford AU

2-15660

2-15660 NA FROM ACE

2-15661 NA FROM ACE

2-15662 1MM Spacer

2-15663 Pintle Cap; Ribbed for BNW w/4MM hole for 24V engine

2-15669 SPI/TBI Plastic Clip Cover

2-15671 Pintle Cap

2-15671 Pintle Cap- Bosch Cone Type Single Point Injector

2-15672



IMPORTANT




Numerical Parts Listing

2-15672 NA FROM ACE

2-15673 Upper O-Ring - Nissan SPI / MPI


2-15679 14.5 MM O-RING Brown

2-15682 Hitachi InjectorO'Ring Seal - Upper Large


2-15687 NA FROM ACE

2-15689 O-RING, PKG

2-15690 Top O-Ring for Mazda Side Feed Injectors

2-15692 NA FROM ACE

2-15693 NA FROM ACE

2-15698 Pintle Cap - Large Hole Type for "V" Spray Injectors

TBA Brass / Plastic Filter Basket for Lucas Injectors

TBA Brass / Wire Filter Basket for Weber Injectors


echlin digital fuel injector belden flow bench and ......bosch k-jet various types page bosch...

Documents