ecad
TRANSCRIPT
![Page 1: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/1.jpg)
re Transistor Model
![Page 2: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/2.jpg)
The three amplifier networkconfigurations are:
The amplifier is a common-emitter when the emitterterminal is connected directly to the reference point,the input signal is applied to the base, and theoutput signal is connected on the collector.
The amplifier is a common-collector when thecollector terminal is connected directly to thereference point, the input signal is applied to thebase, and the output signal is taken at the emitterterminal.
The amplifier is a common-base when the base isconnected to ground point, the input signal isconnected to the emitter, and the output is on thecollector.
![Page 3: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/3.jpg)
Steps in obtaining the ac equivalent network:Step 1. Set all dc sources to zero and replace
them by equivalent short-circuit.Step 2. Replace all capacitors by a short-
circuit equivalent.Step 3. Remove all resistors bypassed by the
shorted capacitors.Step 4. Redraw the network.
![Page 4: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/4.jpg)
CE Fixed-bias Configuration
Input voltage ( Vi) is applied at the base of the transistor.Input voltage ( Vi) is applied at the base of the transistor.
Output voltage ( Vo) is taken at the collector terminal.Output voltage ( Vo) is taken at the collector terminal.
Emitter is the common terminal.Emitter is the common terminal.
CB and CC are coupling capacitors for the input and outputCB and CC are coupling capacitors for the input and outputvoltages.voltages.
There is no emitter resistor.There is no emitter resistor.
The negative sign in the equation for Av tells that a 180The negative sign in the equation for Av tells that a 180°°phase shift occurs between the input and output signals.phase shift occurs between the input and output signals.
The input signal isThe input signal is capacitivelycapacitively coupled to the base throughcoupled to the base throughCB, causing IB to vary above and below its dc bias value.CB, causing IB to vary above and below its dc bias value.
The purpose of biasing is to establish a QThe purpose of biasing is to establish a Q--point about whichpoint about whichvariations in voltage and current occur in response to anvariations in voltage and current occur in response to aninput signal.input signal.
![Page 5: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/5.jpg)
CE Fixed Bias Configuration
![Page 6: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/6.jpg)
PARAMETERS AC FORMULAS AC FORMULAS(effect of ro)
Ac emitterresistance, re
26 mV / IE no effect
Rin(base) β re no effect
InputImpedance
Zi
RB // Rin(base) no effect
OutputImpedance Zo
Rc Rc//ro
Voltage GainAv = Vo/Vi
-Rc / re -(Rc//ro)/re
Current GainAi = Io / Ii
![Page 7: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/7.jpg)
Vi and Vo phase relationship
The negative sign in the equation for Avreveals that a 180˚ phase shift occursbetween the input and output signals.
![Page 8: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/8.jpg)
CE Emitter-bias Configuration
Input voltage ( Vi) is applied at the base of theInput voltage ( Vi) is applied at the base of thetransistor.transistor.
Output voltage ( Vo) is taken at the collectorOutput voltage ( Vo) is taken at the collectorterminal.terminal.
CB and CC are coupling capacitors for the inputCB and CC are coupling capacitors for the inputand output voltages.and output voltages.
There is no emitterThere is no emitter--bypass capacitor.bypass capacitor. Emitter is at ac ground.Emitter is at ac ground. The negative sign in the equation for Av tellsThe negative sign in the equation for Av tells
that a 180that a 180°° phase shift occurs between the inputphase shift occurs between the inputand output signals.and output signals.
![Page 9: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/9.jpg)
AC Equivalent Network
![Page 10: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/10.jpg)
PARAMETERS AC FORMULAS
Ac emitterresistance, re
26 mV / IE
Rin(base) β re
Input ImpedanceZi
RB // ZB
Output ImpedanceZo
Rc
Voltage GainAv = Vo/Vi
- Rc / (re + RE )
Current GainAi = Io/Ii
βRB / ( RB + ZB)
ZB Β(re + RE)
![Page 11: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/11.jpg)
CE Voltage Divider Configuration
Input voltage ( Vi) is applied at the base of theInput voltage ( Vi) is applied at the base of thetransistor.transistor.
Output voltage ( Vo) is taken at the collectorOutput voltage ( Vo) is taken at the collectorterminal.terminal.
Emitter is the common terminal.Emitter is the common terminal. The negative sign in the equation for Av tellsThe negative sign in the equation for Av tells
that a 180that a 180°° phase shift occurs between the inputphase shift occurs between the inputand output signals.and output signals.
CB and CC are coupling capacitors for the inputCB and CC are coupling capacitors for the inputand output voltages.and output voltages.
CE is the emitterCE is the emitter--bypass capacitor.bypass capacitor.
![Page 12: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/12.jpg)
Voltage Divider
![Page 13: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/13.jpg)
PARAMETERS AC FORMULAS
Ac emitterresistance, re
26 mV / IE
Rin(base) β re
Input ImpedanceZi R12 // Rin(base)
Output Impedance Zo Rc
Voltage GainAv = Vo/Vi
-Rc / re
Current GainAi = Io/Ii
R12 / (R12+re )
R12 R1 // R2
![Page 14: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/14.jpg)
Common Base
Input is applied at the emitter.Input is applied at the emitter.
Output is taken at the collector terminalOutput is taken at the collector terminal
Base is the common terminal.Base is the common terminal.
Used mainly as RF amplifier.Used mainly as RF amplifier.
Current gain is slightly less than one.Current gain is slightly less than one.
Vo and Vi are in phase.Vo and Vi are in phase.
Input impedance is low.Input impedance is low.
Output impedance is high.Output impedance is high.
![Page 15: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/15.jpg)
AC Equivalent Circuit
![Page 16: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/16.jpg)
PARAMETERS AC FORMULAS
Ac emitterresistance, re
26 mV / IE
InputImpedance
Zi
RE//re
OutputImpedance Zo
Rc
Voltage GainAv = Vo/Vi
Rc/re
Current GainAi = Io/Ii
- α [ RE / ( RE + re)] ≈ -α ≈ -1
![Page 17: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/17.jpg)
CC EmitterCC Emitter--follower Configurationfollower Configuration
Input is applied at the base.Input is applied at the base.
Output is taken at the emitter terminalOutput is taken at the emitter terminal
Collector is the common terminal.Collector is the common terminal.
Used for impedanceUsed for impedance--matching purposes.matching purposes.
Used as an isolation amplifier.Used as an isolation amplifier.
Vo and Vi are in phase.Vo and Vi are in phase.
Input impedance is high.Input impedance is high.
Output impedance is low.Output impedance is low.
The output voltage is always slightly less than the inputThe output voltage is always slightly less than the inputsignal.signal.
Capacitors CB and CE must have a negligible reactance atCapacitors CB and CE must have a negligible reactance atthe frequency of operation.the frequency of operation.
![Page 18: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/18.jpg)
AC Equivalent Circuit
![Page 19: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/19.jpg)
PARAMETERS AC FORMULAS
Ac emitterresistance, re
26 mV / IE
Rin(base) β re
InputImpedance
Zi
RB //ZB
OutputImpedance Zo
re // RE
Voltage GainAv = Vo/Vi
RE / ( RE + re)
Current GainAi = Io/Ii
-β [ RB / ( RB + ZB)]
ZB β(re + RE)
![Page 20: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/20.jpg)
Collector DC Feedback
![Page 21: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/21.jpg)
SUMMARY OF AC PARAMETERSFOR CE, CC, AND CB AMPLIFIERCHARACTERISTI
CSCOMMON
BASECOMMON
EMITTERCOMMONCOLLECTOR
Power Gain, Ap moderate highest moderate
Voltage Gain, Av highest moderate lowest (less than 1)
Current Gain, Ai lowest(lessthan 1)
moderate highest
Input Impedance,Zi
lowest moderate highest
OutputImpedance, Zo
highest moderate lowest
Phase Inversion none 180o out–of-phase
none
Application RF amplifier The most widelyused type ofBJT amplifier
Isolator
![Page 22: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/22.jpg)
![Page 23: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/23.jpg)
![Page 24: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/24.jpg)
A cascade connection is a series configuration withthe output of one stage then applied as input to thesecond stage.
Two or more transistors can be connected together toincrease the overall gain.
Each transistor that amplifies the signal is considereda stage.
The overall voltage gain ( AVT) is the product of thegain for each stage.
The initial stage of the amplifier must have a very highinput impedance to avoid loading the source.
Coupling capacitors prevent the dc bias of one stagefrom affecting the dc bias of another stage ( capacitorsblock dc).
CASCADE
![Page 25: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/25.jpg)
Multistage Voltage Gain, AVT
The overall voltage gain of cascaded amplifiers is theproduct of the individual voltage gains.
Voltage gain expressed in decibels (dB)
Av(dB) = 20logAv
Overall voltage gain in dB of multistage system
AVT(dB) = AV1(dB) + AV2(dB) + …..AVn(dB)
![Page 26: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/26.jpg)
FORMULAS:
AVT = AV1 AV2 AV3 ….. AVn
AVT(dB) = 20 log [AV1 AV2 AV3 ….. AVn]
![Page 27: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/27.jpg)
Three-Stage Amplifier
![Page 28: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/28.jpg)
CASCODE
A cascode connection has one transistor inseries with another transistor.
This connection is design to provide a highinput impedance with low voltage gain toensure that the input Miller capacitance isminimum.
The overall voltage gain ( AVT) is the productof the gain for each stage.
The voltage gain for the common-emitterstage is approximately equal to one.
![Page 29: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/29.jpg)
Example:
![Page 30: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/30.jpg)
FORMULAS:
Stage 1 ( common-emitter)
Av1 = - re2 / re1 = -1
Stage 2 ( common-base)
Av2 = Rc / re
![Page 31: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/31.jpg)
DARLINGTON CONNECTION
The purpose of this configuration is toincrease the overall current gain which is theproduct of the current gains of the individualtransistor.
Current gain is very large.
βD = β1β2
![Page 32: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/32.jpg)
E
B
C
B
E
C
BD
B2
B1
DARLINGTON CONNECTION
βD = β1 + β2 + β1β2 ≈ β1β2
![Page 33: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/33.jpg)
Darlington emitter-followernetwork.
![Page 34: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/34.jpg)
AC Equivalent Circuit
![Page 35: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/35.jpg)
FORMULASInput Impedance, Zi
Zi = RB // (ri + βDRE )
Output Impedance, Zo
Zo = RE // ri // ( ri / βD )
Voltage Gain, Av
Av = ( RE + βDRE ) / [ ri + ( RE + βDRE)]
Current Gain, AiAi = βDRB / ( RB + βDRE)
![Page 36: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/36.jpg)
Output Section
![Page 37: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/37.jpg)
Power amplifiers are large-signalamplifiers. The larger part of the loadline is used during signal operation.Power amplifiers are commonly usedas the final stage of thecommunication receiver or transmitterto provide sufficient power to anoutput load to drive the speakers or toa transmitting antenna, typically a fewwatts to tens of watts.
![Page 38: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/38.jpg)
CLASS A AMPLIFIERS
This amplifier operates entirely in the linear region of thetransistor’s characteristic curves.
The transistor operate and conduct during the full cycle(360°) of the input signal.
In this mode of operation, the network does not go intocutoff or saturation.
The output voltage signal has the same shape as the inputsignal.
Class A can be either be inverting or noninverting amplifier.
For maximum output signal swing, the Q-point must becentered on the load line.
Maximum efficiency of a class A amplifier is 25%.
![Page 39: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/39.jpg)
Formulas
Maximum currentIc(sat) = IcQ + VCEQ / Rc
AC emitter resistorre = ∆VBE / ∆Ic
Cutoff voltageVCE(CO) = VCEQ + IcQRc
Voltage gain, AvAv = Rc / re
Power gain. ApAp = βDCAv
Q-pointVCEQ = IcQRc
Power (Q-point)PQ = IcQVCEQ
Output load powerPL = V2
CEQ / 2RL
![Page 40: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/40.jpg)
CLASS B AMPLIFIERS
This amplifiers operates in the linear region for half of theinput cycle.
The transistor is cutoff for the other half cycle of the input.
For class B amplifiers, the Q-point is at cutoff
Operated in a push-pull network in order to produce anoutput that is a replica of the input.
Push-pull configuration is a type of class B amplifier withtwo transistors in which one transistor conducts for onehalf-cycle and the other operates for the other half-cycle.
Crossover distortion is the deformation in the output at thepoint where each transistor changes from the cutoff state tothe on state.4
Maximum efficiency is 79%
![Page 41: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/41.jpg)
CLASS AB AMPLIFIERS
This amplifier is biased slightly above cutoffand operates in the linear region for slightlymore than the half cycle of the input.
It eliminates crossover distortion in class Bamplifiers.
![Page 42: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/42.jpg)
CLASS C
Amplifiers that operate in the linear region foronly small part of the input cycle.
This amplifier is biased below cutoff.
Highest efficiency.
Commonly used as tuned amplifier toproduce a sinusoidal output.
The maximum efficiency is higher than that ofeither class A or class B amplifiers.
![Page 43: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/43.jpg)
ComparisonClass of
OperationEfficiency Bias Operating
cycleDistortion
Class A 25 % to50%
Linearregion
360° Low
Class B 79 %(max)
Cutoff 180° High
Class AB BetweenA and B
Abovecutoff
Between Aand B
Moderate
Class C ≈ 100% Belowcutoff
Less than180°
Extreme
Class D Over 90% Pulseoperation
![Page 44: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/44.jpg)
![Page 45: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/45.jpg)
AMPLIFIER FREQUENCYRESPONSE
![Page 46: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/46.jpg)
In the past lessons about amplifiers, thecapacitive reactance, Xc, of the capacitors( CB, CC, and CE) were assumed to beapproximately equal to 0 Ω. Also, the internaltransistor capacitances were assume to besmall enough. We will now consider thefrequency effects introduced by the couplingand bypass capacitors at the low-frequencyend and the internal transistor capacitances(parasitic) at the high frequencies.
![Page 47: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/47.jpg)
LOW-FREQUENCYAMPLIFIER RESPONSE
The capacitively coupled amplifier above hasthree high-pass RC circuits that affect its gain asthe frequency is reduced below midrange.
![Page 48: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/48.jpg)
FOUR CATEGORIES Active Low-Pass Filter (LPF)
A type of filter that passes frequencies below the cutofffrequency (fc) while rejecting higher frequencies.
Active High-Pass Filter (HPF)
A type of filter that passes frequencies above the cutofffrequency while rejecting lower frequencies.
Active Band-Pass Filter (BPF)
A type filter that passes the midrange frequencies lyingbetween the lower-cutoff frequency (f1) and the upper-cutofffrequency
Active Band-Stop Filter (BSF)
Band-Elimination Filter
Notch Filter
Band-Reject Filter
A type of filter that rejects a range of frequencies lyingbetween f1 and f2.
![Page 49: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/49.jpg)
Important Terms
Bandwidth – the usable range offrequencies that pass from input tooutput section
Bode Plot – a comparative plot (graph)of the gain versus frequency used toillustrate the response of an amplifier
Critical Frequency (Cutoff) – frequencyat which the response of a filter is 3 dBless than midrange
Decade – ten times increase ordecrease
Midrange – the part of a responsecurve between the two cutofffrequencies
Octave – two times increase ordecrease
Passband – range of frequencies thatare allowed to pass through a system
Quality Factor – the ratio of the centerfrequency (fo) to its bandwidth (BW)
![Page 50: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/50.jpg)
CE Voltage-Divider
![Page 51: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/51.jpg)
RC Network
![Page 52: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/52.jpg)
Cutoff frequency
![Page 53: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/53.jpg)
INPUT RC CIRCUITOne RC circuit is formed by the inputcoupling capacitor, Cs, and the inputimpedance of the amplifier.
Cutoff frequency due to Cs
Zi = R1 // R2 // Rin = R1 // R2 // βre
![Page 54: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/54.jpg)
OUTPUT RC CIRCUITRC network that is formed by the couplingcapacitor, Cc, and the resistance looking in atthe collector and the load resistance.
Cutoff frequency due to Cc
![Page 55: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/55.jpg)
Considering the effect of ro
![Page 56: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/56.jpg)
BYPASS RC CIRCUIT
Rth = R1 // R2 // Rs
fCE = 1/ ( 2π RTCE ) = 1 / [ 2π(( re + Rth/Β )// RE ) CE ]
![Page 57: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/57.jpg)
THE DOMINANT (highest) LOWERCRITICAL FREQUENCY WILL DETERMINETHE LOWER CUTOFF FREQUENCY, f1, OFTHE SYSTEM.
If fCE < fCB < fCC
then f1 = fCC
If fCC < fCE < fCB
then f1 = fCB
If fCB < fCC < fCE
then f1 = fCE
![Page 58: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/58.jpg)
System Voltage Gain, AVS
Considering the effect of Rs
![Page 59: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/59.jpg)
HIGH - FREQUENCYAMPLIFIER RESPONSE
At the higher frequency end, the transistor’sinternal capacitances begin to have a significanteffect on the gain.
![Page 60: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/60.jpg)
![Page 61: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/61.jpg)
![Page 62: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/62.jpg)
MILLER CAPACITANCEThe interelectrode capacitances between terminals canbe used to simplify the analysis of inverting amplifiersat high frequencies. The coupling and bypasscapacitors have all been replaced by their short-circuitequivalent due to their very low reactance.
![Page 63: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/63.jpg)
Cin(Miller) = Cf ( 1 – Avmid)
Cout(Miller) = Cf ( 1 – 1 / Avmid )
Miller’s theorem states that Cf effectively appears as acapacitance from input to ground. It also states that Cfeffectively appears as a capacitance from output to ground.Avmid = (-Rc//RL)/re
![Page 64: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/64.jpg)
INPUT RC CIRCUIT
RT = Rs // R1 // R2 // Rin = Rs // R1 // R2 // βreCT = Cw(input) + Cbe + Cin(Miller)
![Page 65: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/65.jpg)
Upper cutoff frequency due toinput RC network.
fCi = 1/ ( 2π RTCT ) = 1 / [ 2π( Rs // R1 // R2 //βre) (Cw(input) + Cbe + Cin(Miller) ) ]
![Page 66: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/66.jpg)
OUTPUT RC NETWORK
RT = Rc // RL
CT = Cw(out) + Cce + Cout(Miller)
![Page 67: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/67.jpg)
Upper cutoff frequency due tooutput RC circuit.
fCo = 1/ ( 2π RTCT ) = 1 / [ 2π( Rc // RL )(Cw(iout) + Cce + Cout(Miller) ) ]
![Page 68: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/68.jpg)
THE LOWER OF THE TWOCRITICAL HIGH FREQUENCIESIS THE DOMINANT UPPER –CUTOFF FREQUENCY, f2, OFTHE SYSTEM.
![Page 69: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/69.jpg)
Example1
![Page 70: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/70.jpg)
DIFFERENTIAL AMPLIFIER,DIFF-AMP
An amplifier that produces an outputsignal proportional to the difference of thetwo input signals. It has a very large gainwhen opposite signals are applied to theinputs as compared to the negligible gainresulting from common inputs. Commonlyused for the input stages of anoperational amplifier.
![Page 71: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/71.jpg)
BASIC CIRCUITThe circuit has two separate inputs, two outputs,and both emitter terminals are connectedtogether.
![Page 72: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/72.jpg)
MODES OF SIGNAL OPERATION:SINGLE-ENDED INPUT
Case 1: Vi1 ≠ 0 and Vi2 = 0
Input signal is applied to B1 ( Vi1 ≠ 0 ). B2 is grounded ( Vi2 = 0). Inverted amplified output signal, Vo1, appears at terminal
C1. A signal voltage Ve appears in phase at the emitter of Q1
and Q2 which becomes an input to Q2. Q2 functions as a common-base amplifier. Noninverted amplified output signal, Vo2, appears at
terminal C2. Voltage gain Av1 = - Rc / re. Voltage gain Av2 = +Rc / re.
![Page 73: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/73.jpg)
![Page 74: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/74.jpg)
CONFIGURATION
![Page 75: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/75.jpg)
Case 2: Vi2 ≠ 0 and Vi1 = 0
Input signal is applied to B2 ( Vi2 ≠ 0 ). B1 is grounded ( Vi1 = 0). Inverted amplified output signal, Vo2, appears at terminal
C2. A signal voltage Ve appears in phase at the emitter of Q1
and Q2 which becomes an input to Q1. Q1 functions as a common-base amplifier. Noninverted amplified output signal, Vo1, appears at
terminal C1. Voltage gain Av2 = - Rc / re. Voltage gain Av1 = +Rc / re.
![Page 76: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/76.jpg)
CONFIGURATION
![Page 77: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/77.jpg)
DIFFERENTIAL INPUT
Two opposite-polarity input signals areapplied to the inputs ( double-endedoperation).
Vi1 and Vo2 are in phase.
Vi2 and Vo1 are in phase.
There is a 180° out-of-phase relationshipbetween Vo1 and Vo2.
/ Vo1/ = / Vo2/
![Page 78: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/78.jpg)
![Page 79: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/79.jpg)
COMMON-MODE INPUT
The same input is applied to both inputterminals.
The output signals for both transistors areequal to zero
![Page 80: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/80.jpg)
COMMON-MODE REJECTIONRATIO, CMRR
The ratio between differential voltage gain andcommon-mode gain.
The measure of an amplifier’s ability to rejectcommon-mode signals.
CMRR = ∞ (ideal).
CMRR = Avd / Acm
Where: Avd = differential voltage gainAcm = common-mode gain
Expressed in decibelsCMRR = 20 log ( Avd / Acm)
![Page 81: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/81.jpg)
OPERATIONAL AMPLIFIERS(OP-AMPS)
![Page 82: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/82.jpg)
OPERATIONAL AMPLIFIER
An op-amp is a high gain differential amplifier withhigh input impedance (Zi) and low outputimpedance (Zo). An op-amp contains severalstages of differential amplifier to achieve a veryhigh voltage gain.
![Page 83: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/83.jpg)
Typical op-amp unit
![Page 84: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/84.jpg)
![Page 85: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/85.jpg)
The concept of negative feedback is usedin several op-amp applications. Negativefeedback is the process whereby a portionof the output voltage of an amplifier isreturned to the input with a phase angle
that opposes the input signal.
![Page 86: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/86.jpg)
![Page 87: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/87.jpg)
AC Equivalent Network
![Page 88: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/88.jpg)
OUTPUT VOLTAGE
Op-amp provides an output component that is due tothe amplification of the difference of the signals (Vd)applied to the two inputs and a component due to thesignals common to both inputs (Vc).
Vo = AdVd + AcVc
Where : Vd = difference voltageVd = Vi1 – Vi2
Vc = common voltage( unwanted)Vi1 + Vi2
Vc = --------------2
Ad = differential gainAc = common mode gainAd >> Ac
![Page 89: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/89.jpg)
COMMON MODE REJECTIONRATIO, CMRR
The measure of an amplifier’s abilityto reject unwanted signals. The mainpurpose of differential connection isto amplify the difference signal whilerejecting the common signal (noise)at the inputs.
![Page 90: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/90.jpg)
CMRR = AdAc
CMRRdB= 20 log AdAc
VcVo = AdVd 1 + -------------
CMRR Vd
CMRR = infinite (ideal)the larger the value, the better the circuit operationVo = AdVd + AcVc
Vo = AdVd 1 + AcVcAdVd
![Page 91: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/91.jpg)
DC OFFSSET PARAMETER(output error voltage)
Unwanted voltage and currentgenerated by the internalcircuitry and not by the appliedinput signal.
![Page 92: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/92.jpg)
INPUT OFFSET VOLTAGE; VIO
(1mV ~ 6mV)
When Vi = 0, the circuit acts like annoninverting amplifier.
Vo(offset) = VIO [ 1 + Rf / R1 ]
![Page 93: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/93.jpg)
INPUT OFFSET CURRENT;IIO(20nA ~ 200 nA)
An offset current due to the difference incurrents at the two inputs.
Vo(offset) = IIO Rf
TOTAL OUTPUT OFFSET VOLTAGE
Vo(offset) = VIO [ 1 + Rf / R1 ] + IIO Rf
![Page 94: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/94.jpg)
INPUT BIAS CURRENT , I IB
I+IB + I-IBIIB = ---------------
2I+IB = IIB + IIO
2I-IB = IIB - IIO
2IIO = I+IB - I-IB
![Page 95: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/95.jpg)
FREQUENCY PARAMETERS
fc = f1 / AVD
Where B1 = unity- gain BWf1 = unity- gain freqAVD = voltage differential gain
= open loop voltage gain= 200V/mV typical= 20V/mV (min)
CUTOFF FREQUENCY, fc
![Page 96: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/96.jpg)
SLEW RATE, SR
Slew rate is the maximum permissible rate at which op-ampoutput can change in volts per microsecond. If the rate ofoutput voltage change is greater than SR, the output signalwill be distorted.
SR = ΔVo / Δt
Vo = ACL Vi
ΔVo / Δt = ACL [ ΔVi / Δt ]
SR = ACL [ ΔVi / Δt ]
![Page 97: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/97.jpg)
MAXIMUM SIGNALFREQUENCY
The input frequency of an op-amp is dependent on both thebandwidth and slew rate parameters
ws < SR/ K
K =output gain factorK = ACL Vi
![Page 98: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/98.jpg)
APPLICATIONS:INVERTING AMPLIFIER
Vo = - (Rf / R1) Vi
Zi = R1 + Rf / AOL ≈ R1
Zo = [ AOL / ( 1 + AOL)] Rf // Zout
Zo ≈Zout
![Page 99: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/99.jpg)
Where Zout = open-loop output impedanceZin = open-loop input impedanceAOL = open-loop gainZi = input impedance of the
inverting amplifierZo = output impedance of the
inverting amplifier
B = feedback fractionAOL(mid) = midrange open-loop gainfi = signal frequencyfc = critical frequencyBWCL = closed-loop BW
![Page 100: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/100.jpg)
NONINVERTING AMPLIFIER
Vo = [ 1 + Rf / R1 ] Vi
Zi = [ 1 + AOLB ] Zin
Zo = Zout / ( 1 + AOLB)
![Page 101: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/101.jpg)
UNITY FOLLOWER
A voltage buffer configuration provides a means ofisolating an input signal from a load.
Vo = ViB = 1
ACL = 1Zi = ( 1 + AOL) Zin
Zo = Zout / ( 1+ AOL)
![Page 102: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/102.jpg)
SUMMING AMPLIFIER
Rf Rf RfVo = - ------ V1 + -------- V2 + ---------V3
R1 R2 R3
![Page 103: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/103.jpg)
INTEGRATOR
![Page 104: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/104.jpg)
DIFFERENTIATOR
![Page 105: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/105.jpg)
VOLTAGE DIFFERENCE
![Page 106: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/106.jpg)
INSTRUMENTATIONAMPLIFIER
Vo = [1 + 2Rf / RG ] ( V1 – V2 )
Let R1 = R3 = R2 = R4 = R
Rf1 = Rf2 = Rf
![Page 107: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/107.jpg)
PHASE-SHIFT OSCILLATOR
Oscillator is a circuit that produces periodic (repeating)waveforms on its output with only the dc supply as arequired input.
fo = 1_____2Π√6 RC
B = 1 / 29
![Page 108: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/108.jpg)
ACTIVE FILTERS
First-order LPF Fourth-order LPF
![Page 109: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/109.jpg)
Values for ButterworthResponse
Order Roll off ratedB/Decade
First stagePoles
First stageDF
Second stagePoles
Second stageDF
Third stagePoles
Third stageDF
1 20 1 Optional
2 40 2 1.414
3 60 2 1.0 1 1.0
4 80 2 1.848 2 0.765
5 100 2 1.0 2 1.618 1 0.618
6 120 2 1.932 2 1.414 2 0.518
![Page 110: ECAD](https://reader034.vdocuments.site/reader034/viewer/2022050919/544729ecb1af9fe9108b4734/html5/thumbnails/110.jpg)
FUNCTION GENERATOR
12
X1k
X10k
R7
C8
X10
C1
12
12
0
X100
Vz2
R8
2
1
1 2
R10
21
X1
1 2
R1
12
0
R2
R6
R11
2
1
C13
12
X10
C7
C12
12
C10
X1k
12
R4
X1
C 5
C140
0
Vz1
12
1 2
X100
C11
C4
C9
C2
X1
1 2
12
X1k
1
3
2
41
1
OUT
+
-
V+
V-
C15 X10k
0
C3
X10k
R921
X100
12
1 2
12
1
3
2
41
1OUT
+
-
V+
V-
R521
X10
12
C6
Vout
12
1
3
2
41
1
OUT
+
-
V+
V-
R3