earth-moving machinery — safety requirements for remote ...b/513/1, earth moving machinery...

raising standards worldwide™

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

BSI Standards Publication

Earth-moving machinery — Safety requirements for remote operator control systems

BS ISO 15817:2012

This is a preview of "BS ISO 15817:2012". Click here to purchase the full version from the ANSI store.

https://webstore.ansi.org/Standards/BSI/BSISO158172012?source=preview

National foreword

This British Standard is the UK implementation of ISO 15817:2012. It supersedes BS ISO 15817:2005 which is withdrawn.

The UK participation in its preparation was entrusted by Technical CommitteeB/513, Construction equipment and plant and site safety, to SubcommitteeB/513/1, Earth moving machinery (International).

A list of organizations represented on this committee can be obtained onrequest to its secretary.

This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application.

© The British Standards Institution 2012

Published by BSI Standards Limited 2012

ISBN 978 0 580 66014 6

ICS 53.100

Compliance with a British Standard cannot confer immunity fromlegal obligations.

This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 March 2012.

Amendments issued since publication

Amd. No. Date Text affected

BRITISH STANDARDBS ISO 15817:2012



Reference numberISO 15817:2012(E)

© ISO 2012

INTERNATIONAL STANDARD

ISO15817

Second edition2012-01-15


Engins de terrassement — Exigences de sécurité relatives aux systèmes de commande à distance utilisés par l'opérateur

BS ISO 15817:2012



ISO 15817:2012(E)

COPYRIGHT PROTECTED DOCUMENT © ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester.

ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org

Published in Switzerland

ii © ISO 2012 – All rights reserved

BS ISO 15817:2012



ISO 15817:2012(E)

© ISO 2012 – All rights reserved iii

Contents Page

Foreword ............................................................................................................................................................ iv

1 Scope ...................................................................................................................................................... 1

2 Normative references ............................................................................................................................ 1

3 Terms and definitions ........................................................................................................................... 2

4 Requirements for remote operator control ......................................................................................... 3

5 Forward-direction marking ................................................................................................................... 8

6 Instructions ............................................................................................................................................ 8 Annex A (informative) Example machine safety label for remote control .................................................... 9

Bibliography ...................................................................................................................................................... 10

BS ISO 15817:2012



ISO 15817:2012(E)

iv © ISO 2012 – All rights reserved

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 15817 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 2, Safety, ergonomics and general requirements.

This second edition cancels and replaces the first edition (ISO 15817:2005), which has been technically revised.

BS ISO 15817:2012



INTERNATIONAL STANDARD ISO 15817:2012(E)

© ISO 2012 – All rights reserved 1


IMPORTANT — The electronic file of this document contains colours which are considered to be useful for the correct understanding of the document. Users should therefore consider printing this document using a colour printer.

1 Scope

This International Standard specifies the essential safety requirements for remote operator control systems used on earth-moving machinery as defined in ISO 6165. It is not applicable to autonomous control systems that enable a machine to work without the assistance of an operator, nor does it apply to the remote control of attachments on non-remote controlled machines.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 6165, Earth-moving machinery — Basic types – Identification and terms and definitions

ISO 6405-1, Earth-moving machinery — Symbols for operator controls and other displays — Part 1: Common symbols

ISO 6405-2, Earth-moving machinery — Symbols for operator controls and other displays — Part 2: Specific symbols for machines, equipment and accessories

ISO 9244, Earth-moving machinery — Machine safety labels — General principles

ISO 13766, Earth-moving machinery — Electromagnetic compatibility

ISO 13850, Safety of machinery — Emergency stop — Principles for design

ISO 15998, Earth-moving machinery — Machine-control systems (MCS) using electronic components —Performance criteria and tests for functional safety

IEC 60068-2-31, Environmental testing — Part 2-31: Tests — Test Ec: Rough handling shocks, primarily for equipment-type specimens

IEC 60529, Degrees of protection provided by enclosures (IP code)

BS ISO 15817:2012


earth-moving machinery — safety requirements for remote ...b/513/1, earth moving machinery...

Documents