eagle double-hung replacement sash kit measuring guidelines · 800.324.5354 | eaglewindow.com eagle...
TRANSCRIPT
800.324.5354 | EagleWindow.com
Eagle® Double-Hung ReplacementSash Kit Measuring Guidelines
To assist you with measuring for Eagle® double-hung replacement sash products, we’ve included typicalsection details of double-hung products comparable to what may be in your home.
Please read these guidelines completely before starting. For questions about this and other Eagle products,see your nearest Eagle Window & Door dealer or visit us online at EagleWindow.com.
Consult your local building code official for applicable building codes and regulations. Thank you forchoosing Eagle products.
Tape measure Angle finder
TOOLS REQUIRED
Vertical Section - Head and Sill DetailHorizontal Section - Side Jamb Detail
Exteriorcasing
Topsash
Exteriorblind stop
Partingstop
GlassSide jamb
Interiorstop Interior
casing
Bottomsash
Interior
Exterior
TYPICAL DOUBLE-HUNG WINDOWS
Exteriorcasing
Top sash
Exteriorblind stop
Parting stopGlass
Head jamb
Interior stop
Interior casing
Bottom sash
InteriorExterior
Glass
Sill Apron
Stool
Carefully inspect the existing windowopenings prior to ordering your Double-Hung Replacement Sash Kit.
If any rotten wood on the frame and stopsof the original window cannot be repairedor replaced, the opening will not be suit-able for a Replacement Sash Kit.
Page 2 800.324.5354 | EagleWindow.com
INSPECT THE OLD WINDOW
Eagle® Double-Hung Replacement Sash Kit Measuring Guidelines
MEASURING THE OPENING
Measure each window, even if they appear to be the same size.Use extreme accuracy when tak-ing measurements.
STEP 2
SASH OPENING WIDTH. For sash opening width, take an inside measurement of the framefrom side jamb to side jamb. Do not measure from jamb liner to jamb liner. Measure inthree locations: top, middle and bottom. Use the smallest measurement of the three andround down to nearest 1/8". Record this measurement on the worksheet provided.
Interior
Interior
Exterior
Side jamb
Sash opening width
Tapemeasure
STEP 1
SILL ANGLE. Eagle Double-HungReplacement Sash Kits are built to fityour specific window frame. The sillangle must be specified to cut angles forjamb liners and to provide you with theproper sill dam.
The easiest way to measure the sill angleis to use an angle finder available atmost hardware stores. Set angle finderon sill and record the angle on the work-sheet provided on page 5.
Anglefinder
Sill
Measure from wood side jamb to wood side jamb.Lower sash not shown for clarity.
Side jamb
Page 3 800.324.5354 | EagleWindow.comEagle® Double-Hung Replacement Sash Kit Measuring Guidelines
MEASURING THE OPENING (CONT’D)
STEP 3
Interior
Headjamb
InteriorExterior
Sash
open
ing
heig
ht
StoolSill
Note: Measure directlybehind stool.
Measure from head jamb to sill.
Tapemeasure
STEP 4
CHECK TO SEE IF FRAME ISSQUARE. In many cases you willfind that one side of the windowor the other has settled, pulling theunit out of square. This will affectany replacement sash placed inthat opening. If the measurementsvary, you may need to adjust thesash opening height measured inStep 3.
A). Measure from the inside cornerof the sill and side jamb on theright side of the unit, up to theinside corner of the side jamb andhead jamb on the left side. Repeatthis step from the opposite corners.
B). If the measurements taken are within 1/8", then the unit issquare. If the measurements are greater than 1/8", then adjust asneeded.
Tapemeasure
Interior
SASH OPENING HEIGHT. Carefully measure the inside height ofthe sash opening from the inside of the head jamb to where theinside face of the bottom sash meets the sill behind the stool.Measure in three locations: left, right and center. Use the small-est measurement of the three and round down to the nearest1/8". Record this measurement on the worksheet provided.
Stool
Exterior
Must be measured and ordered after the sash kit has been installed for proper crosssbar location. Record measurements on worksheet provided.
Page 4 800.324.5354 | EagleWindow.comEagle® Double-Hung Replacement Sash Kit Measuring Guidelines
STEP 5 - FULL INSECT SCREEN OPTION - MEASUREMENT
MEASURING THE INSECT SCREEN
INSECT SCREEN OPENING WIDTH. Measure the distance betweenthe outside jamb casing. Subtract 1/8" from this dimension. This isyour insect screen width.
INSECT SCREEN OPENINGHEIGHT. Measure the dis-tance from the inside ofthe outside head casingdown to the sill where theinsect screen will rest.Subtract 1/8" from thisdimension. This is yourinsect screen height.
CROSS BAR LOCATION.Measure from the top ofthe insect screen openingheight, down to the cen-ter of the check rail.
Outsidehead casing
Sill
STEP 5 - HALF INSECT SCREEN OPTION - MEASUREMENT
HALF INSECT SCREEN WIDTH. Measure the distancebetween each jamb liner (opening width) and add 7/8".This is your overall insect screen width.
HALF INSECT SCREEN HEIGHT. Measure the distance between the bottomof top sash and sill (opening height). Subtract 5/16" from this dimension.Choose style: flanges on 2 sides or flanges on 3 sides.
InteriorExterior
Sill
Must be measured and ordered after the sash kit has been installed. Record measurements on worksheet provided.
Interior
ExteriorOutsidejamb casing
Interior
Cross barlocation(center ofcheck rail)
Interior
Exterior
Jambliner
Exterior Interior
Half Insect Screen(Flange 2 Sides)
Half Insect Screen(Flange 3 Sides)
Top sashTop sash
Sill
Opening - 5/16"= Half insect screen height
Opening width + 7/8"= Half insect screen width
Insect screen opening width
Insectscreenopeningheight
Cross barlocation
Opening - 5/16"=Half insect screenheight
Page 5
STEP 2 STEP 4STEP 3STEP 1
Existing Window Opening
Note: Eagle Window & Door only accepts unit “make size” measurements. It remains the customer’sresponsibility to subtract from the inside opening dimensions to get the unit make size.
Qty Sill Angle Width HeightWindow/Location
1 Example 8˚ 24-1/8" 48-1/8" 24-3/8" 48-7/8"
ScreenWidth
ScreenHeight
800.324.5354 | EagleWindow.comEagle® Double-Hung Replacement Sash Kit Measuring Guidelines
Project Name: Measured By:
Date:
“Eagle” and all other marks denoted are trademarks of Eagle Window & Door Manufacturing, Inc.
©2010 Eagle Window & Door Manufacturing, Inc. All rights reserved.
MEASUREMENT WORKSHEET
Full
Screen Type
Full ScreenCross Bar
24"
(Full Screen)
(Half ScreenFlange 2 Sides)
(Half ScreenFlange 3 Sides)