e83 rear-view camera retrofit
TRANSCRIPT
-
8/15/2019 E83 Rear-View Camera Retrofit
1/15
© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
Original BMW Accessory.Installation Instructions.
1
Rear-view camera retrofitBMW X3 (E
83)
These installation instructions are only valid for US cars with SA 609 (navigation system).
Retrofit kit no. 66 21 0 397 639 Rear-view camera retrofit kit66 21 0 397 650 Handle strip with rear-view camera
Installation timeThe installation time is approx. 2.75 hours, but may vary depending on the condition of the car and theequipment in it.
Important informationThese installation instructions are primarily designed for use within the BMW dealership organizationand by authorized BMW service companies.
In any event, the target group for these installation instructions is specialist personnel trained on BMWcars with the appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manualsand work instructions, in a rational order, using the prescribed tools (special tools) and observing currenthealth and safety regulations.
To avoid unnecessary extra work and/or costs, if any installation or function problem occurs,after a brief troubleshooting session (approx. 0.5 hours), please contact the following:1. Either your national subsidiary or your regional office, or2. The Support team via the Aftersales Assistance Portal (ASAP), using the optional technicalparts support application.Specify the chassis number and the part number of the installed retrofit kit and give a precisedescription of the problem.
Do not archive the hard copy of these installation instructions since daily updates are made by ASAP!
Pictograms
Denotes instructions that draw your attention to dangers.
Denotes instructions that draw your attention to special features.
Denotes the end of the instruction or other text.
Subject to technical modifications.
!
-
8/15/2019 E83 Rear-View Camera Retrofit
2/15
2© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
Installation informationEnsure that the cables/lines are not kinked or damaged as you install them in the car. Costs incurred asa result of this will not be reimbursed by BMW AG.
Additional cables/lines that you install must be secured with cable ties.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
Ordering instructions
The handle strip with rear-view camera B is not included in the retrofit kit and must be ordered separately(see EPC for part number and details).
Special tools requiredNone
-
8/15/2019 E83 Rear-View Camera Retrofit
3/15
3© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
Contents
Section Page
1. Parts overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Preparatory work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Connections diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. To install the handle strip with rear-view camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. To install and connect the wiring harness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7. To install and connect the switchbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Concluding work and coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9. Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
-
8/15/2019 E83 Rear-View Camera Retrofit
4/15
4© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
1. Parts overview
Legend
This is a universal retrofit kit. Only the illustrated parts are used.
A Wiring harness
B Handle strip with rear-view camera (not supplied in the retrofit kit)
C Control module
D Protective strip
E Cable tie 292 x 4.8 mm (1x)
F Cable tie 200 x 3.6 mm (20x)
G Miniature connector (3x)
J Adapter cable
K Supply cable
L Switchbox
V Socket casing
W Plug casing
X Socket contact
Y Plug contact
Z Grommet
AA Information sticker
DO NOT RELY ONLY ON CAMERA WHILE BACKING UP
083 0544 Z
GD F
A B C
E
V
L
W X Y
J K
Z
AA
-
8/15/2019 E83 Rear-View Camera Retrofit
5/15
5© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
2. Preparatory work
TIS No.
Conduct a brief test ---
Disconnect negative pole of battery 12 00 ...
The following components must be removed first of all
Tailgate trim 51 49 000
Exterior trim on the tailgate ---
Handle strip (no longer required) 51 24 145
Rear trunk floor trim 51 47 131
Flap in the trunk trim on the right 51 47 172
Roof pillar trim, rear (D pillar) right 51 43 252
Rear closing panel trim ---
Flap in the trunk trim on the left 51 47 172Navigation computer 65 90 510
-
8/15/2019 E83 Rear-View Camera Retrofit
6/15
6© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
3. Connections diagram
Branch
/Item
Designation Signal Cable color /
Cross-section
Connection location in car Abbreviation
/ Slot
A Wiring harness --- --- --- ---
A1 Black 12-pin socket casing --- --- On control unit C ---
A2 Cable open RFS GN
0.75mm2
Cars built before 08/06 only
To right rear reversing l ight,
with miniature connector on blue/yellow cable
Cars built after 08/06 only
To right rear reversing l ight,
with miniature connector on blue/yellow cable
X328
PIN 3
X328
PIN 4
A3 Cable open RFS GN
0.75 mm2
Insulate and tie back---
A4 Socket contact Video + Transparent
0.14 mm2
On branch K1 PIN 24
A5 Socket contact Video - SW/BR
0.35 mm2
On branch K1 PIN 11
A6 Socket contact RSF inv SW
0.25 mm2
On branch K1 PIN 23
A7 Socket contact Terminal 30 RT
0.75 mm2
On branch K1 PIN 25
A8 Socket contact Terminal 31 BR
0.75 mm2On branch K1 PIN 12
A9 Socket contact TA WS
0.25 mm2
Insulate and tie back---
083 0459 Z
A1
A7
A8
A9
A5
A6
A2
A3
A4
J5
J4
J3
J1
J2J
K1 K2
K3
K
A
-
8/15/2019 E83 Rear-View Camera Retrofit
7/15
7© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
3. Connection diagram
Branch
/Item
Designation Signal Cable color /
Cross-section
Connection location in car Abbreviation
/ Slot
J Adapter cable --- --- --- ---
J1 Natural 18-pin socket casing --- --- On switchbox L ---
J2 Socket contact Terminal 30 RT/GE
0.75 mm2
On branch K1 PIN 26
J3 Socket contact Terminal 31 BR
0.75 mm2
On branch K1 PIN 13
J4 Blue 18-pin plug casing --- --- On standard wiring harness X1313
J5 Blue 18-pin socket casing --- --- On navigation computer ---
K Supply cable --- --- --- ---
K1 Blue 26-pin socket casing --- --- On switchbox L ---
K2 Black 1-pin socket casing Terminal R Violet/White
0.50 mm2
On navigation computer, twin-lead terminal with
terminal parts V - Y to violet/white cable
X1312
PIN 3
K3 Black 1-pin plug casing Terminal R Violet/White
1.50 mm
On navigation computer, twin-lead terminal with
terminal parts V - Y to violet/white cable
X1312
PIN 3
083 0459 Z
A1
A7
A8
A9
A5
A6
A2
A3
A4
J5
J4
J3
J1
J2J
K1 K2
K3
K
A
-
8/15/2019 E83 Rear-View Camera Retrofit
8/15
8© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
4. Installation and cabling diagram
Legend
A Wiring harness
B Handle strip with rear-view camera
C Control module
J Adapter cable
K Supply cable
L Switchbox
1 Navigation computer
083 0461 Z
C
B
A
L 1
J/K
-
8/15/2019 E83 Rear-View Camera Retrofit
9/15
9© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
5. To install the handle strip with rear-view camera
Mark the specific dimensions on the trunk lid (1)starting from the speed nuts (4) and the edge (3).
Drill through the trunk lid (1) at the drillingposition (2) using a 12 mm twist drill bit.
Deburr the hole and coat the bare surfaces withpreservative.
Unclip the handle strip (1) from the trim (2).
Do not damage the painted exterior of thetrim (2).
Mark the specified dimensions on the trim (2) andsaw out the marked area (1).
Clip the handle strip with rear-view camera B intothe trim (1).
Push grommet Z onto the camera cable (2).
Not illustrated:
- Route the camera cable (2) through the hole inthe trunk lid.
- Insert grommet Z into the hole in the trunk lidand fit the trim (1).
083 0542 Z
72 mm50 mm
1
3
7 m m
4
2
083 0278 Z
1
2
083 0543 Z
1
2
68 mm
45 mm
7 m m
083 0547 Z
1
B
Z2
-
8/15/2019 E83 Rear-View Camera Retrofit
10/15
10© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
6. To install and connect the wiring harness
Connect the connection plug (2) of the rear-viewcamera and branch A1 (black 12-pin socketcasing) to control unit C.
Affix protective strip D to control unit C. Cut off
any excess lengths.Use cable tie E to secure control unit C to theexisting hole in the trunk lid (1).
Route wiring harness A to the right-hand side.
Cars built before 08/06 only
Connect branch A2, green cable, to the blue/yellow cable from plug X328 (PIN 3) usingminiature connector G.
Cars built after 08/06 only
Connect branch A2, green cable, to the blue/yellow cable from plug X328 (PIN 4) usingminiature connector G.
All carsRoute wiring harness A along the standard wiringharness through the grommet (1) into the right-hand side of the trunk.
Route wiring harness A along the standard wiringharness to the left side of the trunk.
1
E
2
D
A1
083 0463 Z
C
A
X328
A2
A2
G
083 0464 Z
1
A
083 0288 Z
083 0289 Z
A
-
8/15/2019 E83 Rear-View Camera Retrofit
11/15
11© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
6. To install and connect the wiring harness
Remove the draw-in tool (1) from wiringharness A.
Insulate branch A3, GN cable, and branch A9,WS cable, and tie them back.
Connect branches A4 – A8 to branch K1 asfollows:
- Branch A4, transparent cable, to PIN 24
- Branch A5, black/brown cable, to PIN 11
- Branch A6, black cable, to PIN 23
- Branch A7, red cable, to PIN 25
- Branch A8, brown cable, to PIN 12
Connect branches J2 and J3 to branch K1 asfollows:
- Branch J2, red/yellow cable, to PIN 26
- Branch J3, brown cable, to PIN 13
083 0545 Z
1
A
A3-A9K1
083 0467 Z
J3
J2
K1
083 0468 Z
-
8/15/2019 E83 Rear-View Camera Retrofit
12/15
12© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
7. To install and connect the switchbox
Connect branches J1 and K1 to switchbox L.
Route branches K2 and K3, violet/white cables,to the navigation computer (1).
If the violet/white cable has a cross-sectiongreater than 0.75 mm², use a twin-lead
terminal with the terminal parts V – Y.3
Cut the socket contact off branch K2 and con-nect it to the violet/white cable from plug X1312 (Bordeaux 18-pin socket casing, PIN 3) usingminiature connector G.
Route branches J4 and J5 to the navigationcomputer (1).
Disconnect blue plug X1313 from the navigationcomputer (1).
- Connect branch J4 to plug X1313
- Connect branch J5 to the navigationcomputer (1)
Install the navigation computer (1).
Secure switchbox L to the standard wiringharness (1) using cable ties F.
L
K1J1
083 0469 Z
083 0470 Z
G
1
V-Y
X1312
K2/K3
X1313
J4
J5
1
083 0471 Z
083 0546 Z
1
F
L
-
8/15/2019 E83 Rear-View Camera Retrofit
13/15
13© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
8. Concluding work and coding
This retrofit system does not require coding.
- Connect the battery
- Conduct a brief test
Check the function of the rear-view camera as follows:
- Turn on the ignition
- Engage reverse; an image must appear on the on-board monitor
- Disengage reverse gear; the on-board monitor must switch over after approx. 5 seconds
- Re-assemble the car
Affix information sticker AA under the on-boardmonitor (1).
D O N O T R E L Y O N L Y O N CA
M E RA W H IL E BA C K I N G U P
MENU
On-Board Computer
DSP
Emergenc y
GPS-Na vigation
Telephone
Monitor O ff
11:21am 03/07/2006
Settings
1
AA
083 0650 Z
-
8/15/2019 E83 Rear-View Camera Retrofit
14/15
14© BMW AG, Munich 01 29 0 406 876 11/2006 (Z/Z)
9. Circuit diagram
x
J 1 *
A 1 1 2
J 5 *
3
1 0
1
9
1 8
1 8
9
1 2
3
1 0
1 3
1
2 6
1 0
0 , 7 5 R T / G E
6 1 3
1 5 5
0 , 3 5 S W
5 1 4
1 4 6
0 , 3 5 S W
7 1 5
1 6 4
0 , 3 5 S W
5
1 4
6
1 5
N A V N F -
N A V N F +
V M C L 3 1
K - B u s
3 1
3 0
N A V B
N A V B 3 1
N A V G
N A V G 3 1
N A V R
N A V R 3 1
7
1 6
K - B u s
3 1
3 0
N A V N F +
N A V N F -
N A V G
N A V G 3 1
N A V B
N A V B 3 1
N A V R
N A
V R 3 1
1 2
V M C L 3 1
0 , 7
5 G E / B R
0 , 7
5 G E / S W
0 , 7
5 B R
0 , 7
5 R T / G E
0 , 5
0 B R / S W
0 , 5
0 W S / G R / G E
0 , 5
0 V I / W S
K 1 * L
*
3 1
3 0
R
0 , 7 5 B R
N A V B
N A V B 3 1
N A V G
N A V G 3 1
N A V R
N A V R 3 1
1 8
7 0 , 3 5 S W
1 7
9 0 , 3 5 S W
1 6
8 0 , 3 5 S W
N A V B
N A V B 3 1
N A V G
N A V G 3 1
N A V R
N A V R 3 1
0 , 3 5 G N
0 , 3 5 W S
0 , 3 5 S W
0 , 3 5 S W
0 , 3 5 W S
0 , 3 5 G N
0 , 7 5 R T / G E
0 , 7 5 B R
V i d e o -
2 4
2 5
1 2
2 3
0 , 7 5 R T x
0 , 7 5 B R x
0 , 3 5 S W / B R x
2
1
5
6
1 2
1 1
3 0
3 1
R S F i n v
V i d e o +
V i d e o -
3 0
3 1
R S F i n v
V i d e o + 0 , 1 4 t r a n s p a r e n t
C *
0 , 2 5 S W x
K 2 *
1 , 5
0 V I / W S
K 3 *
x
0 , 2
5 S W
x 0 , 2
5 R T
x
0 , 2
5 W S
x
3 4 2 1
3 1
+ 6 V
V i d e o +
V i d e o -
0 , 2
5 G E
B *
X 1 *
A 1 *
3
R S F
A 2 *
A 3 *
0 , 7
5 G N
0 , 7
5 G N
A 9 *
0 , 2
5 W S
4
T A
J 4 *
X
1 3 1 3
0 8 3 0 4 7 3 Z
-
8/15/2019 E83 Rear-View Camera Retrofit
15/15
15© BMW AG Munich 01 29 0 406 876 11/2006 (Z/Z)
9. Circuit diagram
Key
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.
Cable colours
A112 Navigation computer
A1* 12-pin plug SW
A2* Open cable, RFS terminal pick-upA3* Open cable, insulate and tie back
A9* Socket contact, insulate and tie back
B* Handle strip with rear-view camera
C* Control module
L* Switchbox
J1* Natural color 18-pin plug
J4* Blue 18-pin plugJ5* Blue 18-pin plug
K1* Blue 26-pin plug
K2* Black 1-pin plug, terminal R pick-up
K3* Black 1-pin plug, terminal R pick-up
X1* 4-pin plug SW
X1313 Blue 18-pin plug
BL Blue
BR Brown
GE Yellow
GN Green
GR Grey
RT Red
SW Black
VI Violet
WS White