e2004_computer aided design 1_unit3

7/30/2019 E2004_Computer Aided Design 1_UNIT3

1/44

E2004/3/1

DRAWING AIDS , DRAWING LIMITS & DISPLAY CONTROL

DRAWING AIDS,

DRAWING LIMITS AND DISPLAY CONTROL

OBJECTIVES

General Objective :To understand and apply the concept of drawing aids, drawing

limits and display control

Specific Objectives : At the end of the unit you will be able to :

Specify the Snap and Grid increment.

Use the Setup and Create New Drawing dialog boxes

to accomplish basic drawing setup.

Use the various OSNAP command options.

Use the various ZOOM command options.

Adjust the display using Realtime ZOOM and PAN

modes.

Use the Ariel View feature to Zoom and Pan different

parts of a drawing.

Create and restore views with the View Control dialog

box.

Use and distinguish the REDRAW, REGEN, and

REDRAWALL commands.

UNIT 3


2/44

E2004/3/2


DRAWING AIDS

3.0 INTRODUCTION

When placing a line, arc or circle in a drawing, the easiest method is to enter pointby selecting a point in the drawing windows. The problem with these methods is that

it is inaccurate. To assist you in selecting points in the drawing windows, you can

setup the drawing aids to suit the design requirements of your current project.

AutoCAD provides with a number of features that will increase your efficiency and

make more productive. Many of these features are contained in the Drawing Aids

dialog box. They include Snap, Gridand Ortho as shown in the Figure 3.1

Figure 3.1 : Drawing Aids Dialog Box

Methods for opening the Drawing Aids dialog box include:

Menu : Tools> Drawing Aids

Command : DDRMODES

INPUT 3a


3/44

E2004/3/3


The Ortho option is used to turn Ortho mode ON or OFF. By selecting Ortho command, we

can draw a line weather horizontal or vertically.

The Solid Fill mode option controls whether objects such as Polylines with widths and

Solids are displayed filled or in outline. This mode can be controlled from the command line

using the FILL command.

When Quick Text is checked, all text objects in the drawing will be displayed with empty

boundary boxes. This option is often used to increase Regen and Redraw times when the

drawing has a lot of text. This mode can also be set using the QTEXT command.

The Blips option controls whether temporary blips will be displayed when points are pickedor entered. Blips can be removed from the display using the Redraw command but they can

only be suppressed completely by turning Blip mode OFF. This mode can also be set using

the BLIPMODE system variable.

Highlight mode determines whether objects are highlighted or not when they are selected.

You can also control highlighting using the HIGHLIGHT system variable.

The Groups option turns automatic Group selection ON and OFF. When Groups mode is

turned ON, selecting an object which is a member of a previously defined group will

automatically select the whole group.

The Hatch option determines whether the hatch boundary is selected when a hatch object is

selected or not. When this mode is turned ON, the boundary is automatically selected with

the hatch.

3.1 SNAP

SNAP, when activated by pressing F9 or double-clicking on SNAP in the status line (

Figure 3.2 ) forces the cursor position to regular increments. The function can be assistance

to you by making it faster and more accurate for creating and editing objects. The default

snap setting is 0.5 The Snap command is used to set the value for these invisible snap

increments. Snap spacing can be set to any value.


4/44

E2004/3/4


Figure 3.2 : The Status Line

The Snap command is easily typed, displaying the options in command line format. The

command line format is as follows:

Command : Snap

Snap spacing or ON/OFF/Aspect/rotate/Style< current value ): ( value or

letter ) ( enter a value or option )

ON/OFF

Selecting ON or OFF accomplishes the same action as toggling the F9 key, pressing

Ctrl+B, or double clicking SNAP on the status line. Typically, SNAP should be ON for

drawing and editing but turned OFF to make object selection easier ( the cursor moves

smoothly to any location with SNAP OFF )

Aspect

The Aspectoption allows specification of unequal X and Y spacing for SNAP. This actioncan also be accomplished in the drawing Aids dialog box by entering different values for X

Spacing and Y Spacing.

Rotate

SNAP can also be rotated about any point and set to any angle. When SNAP has been

rotated, the GRID, ORTHO, and crosshairs automatically follow this alignment.

Style

The style option allows switching between a standard snap pattern ( the default square or

rectangular ) and an Isometric snap pattern. If using the dialog box, toggle Isometric

Snap/Grid On. When the SNAP Style or Rotate angle is changed, the GRID automatically

aligns with it.


5/44

E2004/3/5


3.2 GRID

GRID is visible on the screen, whereas SNAP is invisible. GRID is only a visible display of

some regular interval. GRID and SNAP can be independent of each other. In other words,

each can have separate spacing settings and the active state of each (ON, OFF) can be

controlled independently. The GRID follows the SNAP if SNAP is rotated or changed to

Isometric Style. Although the GRID spacing can be difference than SNAP, it can also be

forced to follow SNAP by using snap option. The default GRID setting is 0.5.

Figure 3.3 : The GRID is ON in the drawing area

The GRID cannot be plotted. It is not comprised of point object and therefore is not part of

the current drawing. GRID is only visual aids.

Grid can be accessed by command line format ( shown below ) or set via the Drawing Aids

dialog box ( Figure 3.2 ).

Command :grid

Gridspacing ( X ) or ON/OFF/Snap/Aspect: (value or letter)

( enter a value or option )

Grid spacing ( X )

If you supply a value for the grid spacing, GRID is displayed at the spacing regardless of

SNAP spacing. If you key in an X as a suffix to the value ( for example, 2X ), the GRID is

displayed as that value times the SNAP spacing ( for example, 2 times SNAP )


6/44

E2004/3/6


ON/OFF

The ON and OFF options simply make the grid visible or not ( like toggling the F7 key,

pressing Ctrl+G or double clicking GRID on the status line.

Snap

The snap option of the grid command forces the GRID spacing to equal that of SNAP, even

if SNAP is subsequently changed.

Aspect

The aspect option of Grid allows difference X and Y spacing ( causing a rectangular rather

than a square GRID )

3.3 THE FUNCTION KEYS

Many of the modes described above can be controlled quickly using the keyboard function

keys. In most cases this is quicker than using a pull-down or the command line. The

function keys are arranged along the top of your keyboard. AutoCAD uses function keys F1

to F10. Their use is described below.

The F1 key on your keyboard brings up the "Help Topics: AutoCAD Help" dialogue box.

You can use this dialogue box to search for help on any AutoCAD command or topic.

Simply follow the instructions in the dialogue box and when you have found the item you

wish to view, click on the "Display" button. You will usually be given a list of options in the

"Topics Found" dialogue box, select the most appropriate and click the "Display" button to

see the item.


7/44

E2004/3/7


Figure 3.4: Help Topic Box

The F2 key is used to toggle (turn ON and OFF) the AutoCAD text window. This is a

floating version of the command window which can be resized to suit your requirements.

The text window contains the whole command history from the beginning of the drawing

session. If you wish, you can scroll back to see which commands you have used. The text

window is also useful for viewing the results of commands like LIST which report to the

command line on a number of lines which may scroll off the command window and make

them difficult to view.

Figure 3.5: AutoCAD Text Windows

The F3 key displays the "Osnap Settings" dialogue box.

The F4 key on your keyboard toggles tablet mode ON and OFF. This only has an effect if a

digitizing tablet has been calibrated.


8/44

E2004/3/8


The F5 key cycles through the Isoplanes, this only has an effect if "Isometric Snap/Grid"

mode is ON. The options are Left, Top and Right. The different options describe the plane

in which Ortho mode works. It also affects the orientation ofIsocircles drawn with the

Ellipse command. The illustration on Figure 3.6shows a cube with isocircles drawn on the

top, left and right faces. Each isocircle was drawn using the corresponding isoplane.

Figure 3.6

The F6 key is a three way toggle which changes the co-ordinate reading in the status bar. By

default the status bar shows co-ordinates using the Cartesian system. You can use the F6 key

to turn the co-ordinate readout OFF and to change to the polar system when you are in pick

mode.

The F7 key is used to toggle grid mode ON and OFF. When grid mode is ON a grid of dots

is shown on the screen as a drawing aid. You can set the grid spacing by using "Drawing

Aids" from the "Tools" pull-down. The grid points do not necessarily reflect the Snap

setting, they can be set independently, and however, you can force the grid to reflect the

snap setting by giving the grid setting a value of zero. The word "GRID" is highlighted in

the status bar when grid is set ON.


9/44

E2004/3/9


The F8 key on your keyboard can be used to toggle Ortho (orthogonal) mode ON and OFF.

When Ortho mode is ON AutoCAD will only allow you to draw either vertical or horizontal

lines. You can think of it as being a computer version of the parallel motion on your

drawing board. You can see if Ortho mode is ON by looking at the status bar. The word

"ORTHO" is highlighted when Ortho is turned ON.

The F9 key can be used to toggle Snap mode ON and OFF. Snap makes the crosshairsjump

to points on a defined grid. The snap spacing can be set using the "Drawing Aids" dialogue

box from the "Tools" pull-down menu. You can also see ifSnap mode is ON by looking at

the status bar.

The F10 key is used to control the display of the status bar, the display can be toggled OFF

and ON.

3.4 OBJECT SNAP

The Object Snaps (Osnaps for short) are drawing aids which are used in conjunction with

other commands to help you draw accurately. Osnaps allow you to snap onto a specific

object location when you are picking a point. For example, using Osnaps you can accurately

pick the end point of a line or the center of a circle. Osnaps in AutoCAD are so importantthat you cannot draw accurately without them. For this reason, you must develop a good

understanding of what the Osnaps are and how they work.

This simple example is to give you an idea how Osnaps work. Follow the command

sequence below to draw a circle and then to draw a line from the center point of the circle to

a point on the circle's circumference at the 12 o'clock position.

To Draw the Circle

Command: CIRCLE

3P/2P/TTR/:

(pick a point in the middle of the drawing window)

Diameter/:

(pick another point to draw the circle, the size is not important)

Figure 3.7


10/44

E2004/3/10


To Draw the Line using Osnaps

Command: LINE

From point: CEN (this is the short-cut for the Center Osnap)

_cen of (pick a point on the circumference of the circle, P1 in the illustration)

To point: QUA (this is the short-cut for the Quadrant Osnap)

_qua of (pick a point on the circumference of the circle, P2 in the illustration)

To point: (to end)

When you use Osnaps you need only pick a point which is near to the point required

because AutoCAD automatically snaps to the object location implied by the particular

Osnap you use. Notice that when you move the cursor close enough to an Osnap location, it

is highlighted with an Osnap marker. Each Osnap has a different marker. As you have

already seen, the Center Osnap marker is a circle and the Quadrant Osnap marker is a

diamond. Notice also that when you move the cursor over a snap point the cursor jumps to

the snap location. This feature is known asMagnet.

One thing that often catches new users out is that when you want to snap to the centre of a

circle, the pick point should be on the circle's circumference. This is because the circle has

no solidity, it is only an outline.

Although you can get quite close to the result above by picking freehand you will never be

able to pick as accurately as you can using Osnaps. Many AutoCAD

commands rely upon the fact that objects have been drawn accurately

and so you should always use Osnaps when you need to pick a point at a

particular location.

There are four basic methods of accessing the Osnaps:

The Osnaps are available from a flyoutbutton on the Standard

toolbar, see illustration on Figure 3.8

Figure 3.8


11/44

E2004/3/11


The Osnaps are also available on their own Object Snap toolbar. If this toolbar is not

already displayed, you can display it using the TOOLBAR command, View

Toolbars from the pull-down menu. When the Toolbar dialogue box appears,

simply check the box next to "Object Snap" in the toolbars list. Many AutoCAD

users work with the Object Snap toolbar permanently dockedon their screen because

it gives one-click access to all of the Osnaps, making drawing much more efficient.

You can also access the Osnaps from the cursor menu. Hold the Shiftkey down on

the keyboard and right-click the mouse to bring up the cursor menu. The menu

appears at the current cursor position.

Finally, you can also access the Osnaps from the keyboard by typing their

abbreviated name.

There are eleven Osnaps in all and although they are all useful in certain situations you will

probably find yourself using about half of them on a regular basis and the other half in

special circumstances. However, it's a good idea to get to know all of the Osnaps so that you

can plan your drawing, knowing all of the tools at your disposal. A sensible use of Osnaps is

the best way to improve your drawing efficiency.

Each of the sections below is accompanied by a small screen-shot illustrating the Osnap in

use. In each case, drawing objects are shown in pale blue (cyan), the Osnap marker is shown

in red and the cursor cross-hairs in white. The corresponding Snap Tip is also shown. Snap

tips appear if you let the cursor hover over an Osnap location for a second or so and have a

similar function to the toolbar Tool Tips.

Endpoint

Toolbar :

Pull-down : Shift + Right ClickEndpoint

Keyboard : END (when selecting objects)


12/44

E2004/3/12


The Endpoint Osnap snaps to the end points of lines and arcs and to polyline vertices. This

is one of the most useful and commonly used Osnaps.

Midpoint

Toolbar :

Pull-down : Shift + Right ClickMidpoint

Keyboard : MID (when picking)

The Midpoint Osnap snaps to the mid poins of lines and arcs and to the mid point of

polyline segments.

Intersection

Toolbar :

Pull-down : Shift + Right ClickIntersection

Keyboard : INT (when picking)

The Intersection Osnap snaps to the physical intersection of any two drawing objects (i.e.

where lines, arcs or circles etc. cross each other) and to Polyline vertices. However, this

osnap can also be used to snap to intersection points which do not physically exist. This

feature is called the Extended Intersection (see the illustration above). To use the apparent

intersection feature, you must pick two points to indicate which two objects should be used.

Apparent Intersect

Toolbar :

Pull-down : Shift + Right ClickApparent Intersect

Keyboard : APP or APPINT (when picking)

Apparent Intersection snaps to the point where objects appear to intersect in the current

view. For example, you may be looking at a drawing in plan view where two line cross, as


13/44

E2004/3/13


in the illustration. However, since AutoCAD is a 3 dimensional drawing environment, the

two lines may not physically intersect. One line may be at ground level and the other may be

10 meters or more above or below ground level. As with the Intersection Osnap, Apparent

Intersection also has an "Extended" mode.

Center

Toolbar :

Pull-down : Shift + Right ClickCenter

Keyboard : CEN (when picking)

The Center Osnap snaps to the centre of a circle, however, the pick point used to pick the

centre must be on the circumference of the circle. This often causes some confusion for new

users.

Quadrant

Toolbar :Pull-down : Shift + Right ClickQuadrant

Keyboard : QUA or QUAD (when picking)

The Quadrant Osnap snaps to one of the four circle quadrant points located at north, south,

east and west or 90, 270, 0 and 180 degrees respectively.

Tangent

Toolbar :

Pull-down : Shift + Right ClickTangent

Keyboard : TAN (when picking)


14/44

E2004/3/14


The Tangent Osnap snaps to a tangent point on a circle. This osnap works in two ways. You

can either draw a line from a point to the tangent point (see illustration) or you can draw a

line from a tangent point, the latter is reffered to as the "Deffered Tangent" snap mode.

Perpendicular

Toolbar :

Pull-down : Shift + Right ClickPerpendicular

Keyboard : PER or PERP (when picking)

The Perpendicular Osnap snaps to a point which forms a perpendicular with the selected

object. As with the Tangent Osnap, Perpendicular can be used to draw a line to aperpendicular point, as in the illustration or from a perpendicular point, known as the

"Deffered Perpendicular" snap mode

Insert

Toolbar :

Pull-down : Shift + Right ClickInsertKeyboard : INS (when picking)

The Insert Osnap snaps to the insertion point of a block, text or an image.

Node

Toolbar :

Pull-down : Shift + Right ClickNode

Keyboard : NODE (when picking)

The Node Osnap snaps to the center of a Point object. This osnap can be useful if you have

created a number of Points with the Measure or Divide commands. You could, for

example insert a number of regularly spaced tree symbols (blocks) along a line by using the

Node Osnap for the insertion point of each block.


15/44

E2004/3/15


Figure 3.9

The image above shows a Spline (cyan). The Measure command has been used to set Points

(red) at regular intervals and a tree symbol has been inserted with the Insert command at

each Point location using the Node Osnap.

Nearest

Toolbar :

Pull-down : Shift + Right ClickNearest

Keyboard : NEA or NEAR (when picking)

The Nearest Osnap snaps to the nearest point on a drawing object. This Osnap is useful ifyou want to make sure that a pick point lies on a drawing object but you don't necessarily

mind exactly where it is located.

From

The From Object Snap is a little more complicated than the other object snaps but it is well

worth getting to know because it can be very useful.

Toolbars :

Pull Down : Shift + Right ClickFrom

Keyboard : FROM ( When Picking )


16/44

E2004/3/16


The From Osnap can be used in conjunction with other osnaps or ordinary pick points and

relative co-ordinates to pick offset points. The From Osnap does not snap to object snap

locations, rather it can be used to snap to points at some distance or offset from an object

snap location. Consider the following example.

Look at the illustration on the right. It shows a circle drawn on top of a line. It is

quite difficult to see how this circle could have been drawn accurately without the use of

construction lines. However, the From Osnap can be used to draw the circle without any

construction lines. Follow the command sequence below to discover how this is done.

To draw theLine

Command:LINE

From point: (pick a point in the lower half of the screen)

To point: @0,30

(this is a relative co-ordinate, 30 units above the first point)

To point: (to end)

To draw the Circle

Command: CIRCLE3P/2P/TTR/: FROM

_from Base point:END ( click at the top of line )

_endp of : @0,10

(this co-ordinate is a point 10 units from the endpoint in the Y direction)Diameter/

: 10

(a radius value of 10 ensures that the southern point on the circle will just touch the top of

the line)

Your drawing should now look like the illustration above. Practice using the From Osnap

until you are quite sure how it works. Don't forget to prefix all co-ordinates with the @

symbol to let AutoCAD know that you are entering a relative co-ordinate. The North Point

exercise below demonstrates more uses of the From Osnap.


17/44

E2004/3/17


3.5 DRAWING LIMITS

The limits command allows you to set the size of the drawing area by specifying the lower

left and upper right corners in X,Y coordinates values. Methods for invoking the limits

command include :

Pull-down menu : Format>Drawing Limits

Command : Limits

When using command line, we can get the following step

Command : limits

Reset Model space limits

ON/OFF/: x,y or Enter ( Enter an X,Y

value or accept the 0,0 default-normally use 0,0 as lower left corner. )

Upper right corner < 19,9>:x,y ( Enter new values to change upper-right corner to

allow adequate drawing area.)

The default Limits values in AutoCAD are 12 and 9; that is, 12 units in the X direction and

9 unit in the Y direction ( figure 3.10 ). Starting a drawing by any of the following methods

( of the setup or create new Drawing dialog boxes ) results in limits of 12 X 9

Figure 3.10


18/44

E2004/3/18


If the GRID is turned ON, the dots are displayed only over theLimits. The AutoCAD screen

( default configuration ) displays additional area on the right past the Limits the units are

generic decimal units that can be used to represent inches, feet, millimeters, miles, or

whatever is appropriate for the intended drawing. Typically, however, decimal units are

used to represent inches or millimeters. If the default units are used to represent inches, the

default drawing size would be 12 by 9 inches.

Remember that when a CAD system is used to create a drawing, the geometry should be

drawn full size by specifying dimensions of object in real world units. A completed CAD

drawing or model is virtually an exact dimensional replica of the actual object. Scaling of

the drawing occurs only when plotting or printing the file to an actual fixed-size sheet of

paper.

Before beginning to create an AutoCAD drawing, determine the size of the drawing area

needed for the intended geometry. After setting Units, appropriate Limits should be set in

order to draw the object or geometry to the real-world size in the actual units. There are no

practical maximum or minimum settings forLimits.

The X,Y values you enter as Limits are understood by AutoCAD as values in the units

specified by the Units command. For example, if you previously specified Architectural

units, then the values entered are understood as inches unless the notation for feet ( ` ) is

given ( 240,180 or 20,15 would define the same coordinate). Remember, you can type in

explicit feet and inch values only ifArchitectural orEngineering units have been specified

as the drawing units

If the ON option of Limits is used, limits checking is activated. Limits checking prevents

you from drawing objects outside of the limits by issuing an outside-limits error. This is

similar to drawing off the paper. Limits checking is OFF by default.


19/44

E2004/3/19


Limits also defines the display area for GRID as well as the minimum area displayed when

Zoom All is used. Zoom All forces the full display of the limits. Zoom All can be invoked

by typingZ ( command alias ) thenA for the all option

Changing Limits does not automatically change the display. As a general rule, you should

make a habit of invoking a Zoom All immediately following a change in Limits to display

the area defined by the new limits ( Figure 3.11 )

Figure 3.11


20/44

E2004/3/20


ACTIVITY 3a

ANSWER ALL THE QUESTIONS BELOW.

3.1 What is the function of Snap and Grid?. How to adjust the Snap 1.5 (X and

Y) spacing and Grid to 2.0 ( X and Y) spacing?

3.2 Complete the steps for the drawing setup below:

Begin a New Drawing. When the Start Up or Create New Drawing dialog

box appears, select Start from Scratch. Select theEnglish default settings.

Set the GRID to 1.

Set SNAP to 0.125

Save this drawing.

3.3 Give the method for accessing the Osnaps and list all the Osnaps.


21/44

E2004/3/21


FEEDBACK TO ACTIVITY 3a

ANSWERS

3.1 The function of Snap and Grid is making faster and accurate for creating and editing

object. It also functions as a guidance for creating objects.

We can adjust the Snap and Grid by using Drawing Aids Dialog Box and set the X

to 1.5 and Y to 2.0 or by type snap / grid and then set the X and Y.

3.4 There are four basic methods of accessing the Osnaps:

Fromflyoutbutton on the Standard toolbar

From TOOLBAR command, View Toolbars from the pull-down menu.

From the cursor menu. Hold the Shiftkey down on the keyboard and right-click

the mouse to bring up the cursor menu. The menu appears at the current cursorposition.

From the keyboard by typing their abbreviated name.

Osnaps List

1. Endpoint

2. Midpoint

3. Intersection

4. Apparent Intersect

5. Center6. Quadrant

7. Tangent

8. Perpendicular

9. Insert

10. Node

11. Nearest


22/44

E2004/3/22


3.6 DISPLAY CONTROL

The accepted CAD practice is to draw full size using actual units. Since the drawing

is a virtual dimensional replica of the actual object, a drawing could represent a vast

area (several hundred feet or even miles) or a small area (only millimeters). The

drawing is created full size with the actual units, but it can be displayed at any size

on the screen. Consider also that CAD systems provide for a very high degree of

dimensional precision, which permits the generation of drawings with great detail

and accuracy.

Display commands provide you with different options for changing the view

of your drawing while it is being created. These commands make it easier to work

with your drawing, and see the overall effects of changes. the commands that

facilitate viewing different areas of a drawing are ZOOM, PAN, and View.

When you use drawing or editing commands, you can utilize the transparent

PAN command and ZOOM command options to change the view and magnification

of a drawing. You can also use display commands for saving and restoring specific

views, or to display several views.

The Viewing commands are found in the View pull-down menu (Figure 3.12 ).

INPUT 3b


23/44

E2004/3/23


The Standard toolbar contains a group of tools (icon buttons) for the Figure 3.12

Viewing commands located near the right end of the toolbar ( Figure. 3.12 ). The

Realtime options of Pan and Zoom, Zoom Previous, and Aerial View each has an

icon permanently displayed on the toolbar, whereas the other Zoom options are

located on flyouts.

Figure 3.12: View pull-down

menu

Figure 3.13: Standard toolbar button

for viewing

Aerial View

Pan Realtime

Zoom Realtime

Zoom Previous


24/44

E2004/3/24


3.7 USING ZOOM COMMAND

When you create a drawing, you may need to change the way objects are viewed in

the drawing window. To achieve this, the orientation, magnification, or position of

the drawing may have to be adjusted. The ZOOM command options let you change

the view by increasing or decreasing the size of displayed images. You zoom in to

magnify objects so you can see more details. You zoom out to reduce objects in the

drawing window and view a larger portion of the drawing.

Zooming does not change the true size of a drawing or object. It only changes the

size of the view in your drawing window. You can view the entire drawing, specify a

display window, or zoom to re a specific scale. We can get Zoom All Toolbar from

Flyout toolbar.

3.7.1 Zoom Window

The Zoom Window option lets you zoom in on an area of your drawing by using a

window to specify the viewing boundaries. When you enter the Zoom Window

option, AutoCAD displays a rectangular window in the drawing window. Select a

point to specify where you want your view to start, then move the window to cover

the area or section you want to magnify ( Figure 3.14 )

Figure 3.14: Using Zoom Window

BeforeAfter

START

END


25/44

E2004/3/25


Methods for invoking the zoom window option include:

Toolbar :

Pull Down Menu : View> Zoom > Window

Command : ZOOM> Window

3.7.2 Zoom Previous

The Zoom Previous option displays the last view of your drawing. This option lets

you restore as many as ten previous views.

Methods for invoking the Zoom Previous option include:

Toolbar:

Menu: View> Zoom> Previous

Command: ZOOM> Previous

3.7.3 Zoom All

The Zoom All option lets you view the entire drawing in the current viewport. The

display shows the drawing limits and all objects even if the objects extend outside of

the drawing limits.

Methods for invoking the Zoom All option include:

Toolbar :

Menu : View> Zoom > All

Command : ZOOM> All


26/44

E2004/3/26


3.7.4 Zoom Extents

The Zoom Extents option displays the region of the drawing where all objects you

draw are located. The display is based just on drawing objects, the drawing limits are

not considered to recalculate the display.

Methods for invoking the Zoom Extents option include:

Toolbar :

Menu : View > Zoom> Extents

Command : ZOOM> Extents

3.7.5 Zoom Center

The Zoom Center option lets you change the displayed size of an object and locate it

in the center of the viewport. When you enter the Zoom Center option, you are

prompted to locate a center point on the drawing plane. The next command prompt

lets you enter a magnification value or a height. The magnification value is followed

by an x which is the relative magnification factor. For the Height option, enter

smaller numbers for the height to enlarge the image size, and enter larger numbers

for the height to decrease the size.

Methods for invoking the Zoom Center option include:

Toolbar:

Menu: View > Zoom > Center

Command: ZOOM> Center

3.7.6 Dynamic

The Zoom Dynamic option uses a viewbox to adjust the display. The view box

represents your viewport. This means that the region of your drawing that you select


27/44

E2004/3/27


with the view box will be displayed in the entire drawing window. You can enlarge,

reduce, and move the viewbox around your drawing to select the desired view.

Methods for invoking the Zoom Dynamic option include:

Toolbar :

Menu : View > Zoom> Dynamic

Command : ZOOM> Dynamic

3.7.7 Zoom Scale

The Zoom Scale option uses a scale factor to adjust the display. The value you enter

should correspond to the limits of the drawing.

The Scale (X) option requires you to use positive numbers to change the

magnification factor. When you enter the X option, the current display can be

enlarged or reduced by a certain multiple. For example, entering 2 at the Zoom Scale

Command prompt will display your drawing at twice its size, relative to its full view.

However, entering 2x at the Zoom Scale Command prompt will display your

drawing at twice the size as displayed in the current view.

You use the Scale (XP) option for scaling the display in floating viewports created in

paper space. This is useful when you are plotting layouts of scaled multiview

drawings.

Methods for invoking the Zoom Scale option include:

Toolbar :

Menu : View> Zoom> Scale

Command : ZOOM> Scale


28/44

E2004/3/28


3.8 REALTIME DISPLAY

3.8.1 Zoom Realtime

When working with complex drawings, you spend significant time using the ZOOM

and PAN commands. After you invoke the command, the Realtime Zoom cursor is

displayed, drag the cursor down to decrease or up to increase the image. To activate

the Realtime ZOOM / PAN menu right-click the mouse.

The ZOOM/PAN cursor menu options include:

Exit - cancels the Realtime option and returns you to the Command prompt

Pan - Switches from Realtime ZOOM to PAN

Zoom - Switches from PAN to Realtime ZOOM

Zoom window - Displays a specified window and returns to REALTIME ZOOM

Zoom Previous - Restores the previous view and returns to the Realtime option

Zoom Extents - Displays the drawing extents and returns to the Realtime option

Methods for invoking the Realtime ZOOM command include:

Toolbar :

Menu : View> Zoom> Realtime

Commands : ZOOM

The Zoom/Pan Cursor menu is shown in the following figure:

Figure 3.15: The ZOOM/PAN Cursor Menu


29/44

E2004/3/29


3.8.2 PAN REALTIME

With the PAN command, you can move the drawing around the drawing window

without changing the magnification. The two options that let you change the display

are Realtime and Point.

Methods for invoking the PAN command include:

Toolbar :

Menu : View> Pan> Realtime

Command : PAN

When you select the Realtime PAN option, the cursor changes into a hand cursor. To

change the location of your drawing, press the left mouse button. This locks the

cursor into its current location relative to the coordinate system used in the current

viewport. As you move the mouse, the drawing image pans to a new location. The

view of the objects in the drawing window shift in the same direction as the cursor.

The PAN Point option lets you specify a single point. AutoCAD then uses the

selected point and the current view orientation to displace the image. You also can

specify two points, AutoCAD computes the displacement between the two points

then moves the image in the drawing window. You can also pan by entering absolute

or relative coordinates at the Displacement prompt. To invoke the Pan Point option,

select Pan from the View menu, then choose Point.

The PAN command also has preset options that move the drawing in the specified

direction. You can access these options from the View menu. They include Left,

Right, Up, and Down. A view of the Pan cascading menu is shown in the following

figure:


30/44

E2004/3/30


Figure 3.16: Pan cascading menu options

3.9 The Aerial View Zoom Feature

The Aerial View feature is a viewing aid that saves drawing time by displaying your entire

drawing in a separate window. You can then use the ZOOM and PAN command options

within the window to change the view of your drawing on the drawing window. If you keep

the Aerial View window open while you work, you can pan and zoom around your drawing

without entering commands at the Command prompt, or accessing them from the View

menu.

Methods for invoking the Aerial View window include:

Toolbar : Standard

Menu : View> Aerial View

Command : DSVIEWER

Figure 3.17: Realtime Pan and Zoom cursor menu


31/44

E2004/3/31


When you enter the Aerial View window, AutoCAD displays the Aerial View window by

default, in the same location and with the same size as it was located in the last drawing

session. This means that you may have to move or change the size of the Aerial View

window so that you can have a better view of the display window. To do so, use the left

mouse button to select the title bar. Drag the window to a desired location and release the

left mouse button. To change the size of the window, move your cursor to one of the four

corners. When you see the doubled-pointed arrow, drag the cursor to change the window

size.

The Aerial View window contains the following four menus labeled View, Mode, Options,

and Help.

The View menu lets you select three zoom options to change the magnification of the Aerial

View. These include Zoom In, Zoom Out, and Global.

Zoom In - Increases the magnification of the drawing in the Aerial View by

zooming in by a factor of 2, centered on the current view box.

Zoom Out - Decreases the magnification of the drawing in the Aerial View by

zooming out by a factor of 2, centered on the current view box.

Global - Displays the entire drawing and the current view in the Aerial View

window.

3.10 USING REDRAW, REGEN AND REGEN ALL

3.10.1 REDRAW

The REDRAW command quickly refreshes the display of the current viewport by

removing all blips and any marks left from the use of editing commands. Blips are

small crosses left on the drawing window after a point is selected. REDRAW is also a

transparent command.


32/44

E2004/3/32


Methods for invoking the REDRAW command include:

Menu : View > Redraw

Command : REDRAW

3.10.2 REGEN and REGENALL

The REGEN command refreshes the drawing window and recalculates all of the

objects in the drawing. When using the REGEN command, it will take AutoCAD a

longer time to redisplay your drawing than if the REDRAW command was used. This

is a major consideration when working with large drawings. The REGEN command

re-indexes the drawing database, re-computes drawing window coordinates for all

objects, and smoothes out all circles, arcs. ellipses, and splines. You may need to use

REGEN after changes in text styles, layer and linetype properties, and other changes

to properties.

Methods for invoking the REGEN command include:

Menu : View > Regen

Command : REGEN

The REGEN command only affects the current viewport. If you are working with

multiple viewports that need to be updated, use the REGENAL, command. The

REGENALL, command works the same way as REGEN except it regenerates all

viewports, and recalculates the drawing window coordinates and view resolution for

all objects in each of the active viewports.

Methods for invoking the REGENALL command include:

Menu :View > Regen All

Command : REGENALL


33/44

E2004/3/33


Example using REGEN ALL

Create the circle with diameter 10mm ( Start new drawing with metric setting ).

Then zoom the circle. The figure below shown that the circle before zoom, after

zoom and after using regen command

Figure 3.18 UsingRegen All to smoother the display of object

Original Drawing After Zoom Windows After Regen All


34/44

E2004/3/34


ACTIVITY 3 b

EXERCISES.

3.5 Controlling the Display

You often use the ZOOM command options to change the view in the drawing

window. In this activity, you use the ZOOM options to display new drawing views.

A. Using the Zoom Command

1. Open the file C:\Program files\AutoCAD R14\Sample\campus.dwg. The drawing

looks like the following figure:

Figure 3.19 : Campus.dwg

2. From the View menu, chooseZoom, then choose Window.

3. In response to the First corner: prompt, select A. For the Other corner: select B.

A

B


35/44

E2004/3/35


The following figure shows the result of using zoom window:

Figure 3.20: Result of using ZOOM Window

4. To recall a previous display, you can use the Zoom command option Previous. At

the Command prompt, enter the command alias z.

5. Enter p at the Command prompt. The previous display is now displayed again.

6. To display all visible objects in the whole drawing, you can use the Zoom Extents

option.

7. From the View menu, choose Zoom, then choose Extents. All visible objects in the

drawings are now displayed.

8. To center an object in the middle of the drawing window, use the Zoom Center

option. At the Command prompt, enter z. Then enter c for the center option.


36/44

E2004/3/36


B. Using Realtime ZOOM and PAN

1. The REALTIME PAN and ZOOM commands let you quickly obtain the display you

want. Open Campus.dwg file and use REALTIME ZOOM

2. To use the REALTIME ZOOM command, enter z and accept the default command

option by pressing ENTER.

3. The Realtime Zoom cursor is now displayed as a magnifying glass with plus and

minus signs. Press the left mouse and drag the Realtime Zoom cursor up and down

the drawing window. When the desired view is displayed in the drawing window,

release the left mouse button.

4. Press the right mouse button. The Pan/Zoom cursor menu is displayed. Select the

Pan option, as shown in the following figure:

Figure 3.21: Realtime Pan and Zoom cursor menu

5. The Realtime Pan cursor is now displayed as a hand in the drawing window. Position

the Realtime Pan cursor over the office building. Drag the cursor around the drawing

window, and when the desired view is displayed in the drawing window, release the

left mouse button and press ENTER.

6. This concludes the ZOOM Command exercise. You are encouraged to explore the

other Zoom command options and command entry methods.

7. Try another ZOOM command ( All, Extents, Center, Dynamics, Scale )


37/44

E2004/3/37


C. Using REDRAW, REGEN and REGEN ALL

Start New drawing. Start From Stractch > Metric. Create a circle with diameter 5

mm. Then zoom the circle using ZOOM Windows commands. What happen with this

circle? Using Regen All to make the circle smoothes

.


38/44

E2004/3/38


FEEDBACK TO ACTIVITY 3b

Please discuss with your lecturer


39/44

E2004/3/39


FOLLOW THE ENTIRE STEP BELOW AND ANSWER THE QUESTION.

QUESTION 3-1

a) Begin a New drawing. When the Start Up or Create New Drawing dialog box

appears, select Start From Scratch. Select theEnglish default settings. Set Limits in

order to draw full size. Make the lower-left corner 0,0 and the upper-right at 24,18.

Set the grid to 1 and snap to 1. Draw the T character as shown below. Save your

drawing.

Figure 3.22

Then, set the Grid to 0.5 What happened with the grid and snap? Discuss with your lecturer.


40/44

E2004/3/40


b) Draw the marker of each Osnap below

Osnap Marker

i. Endpoint

ii. Midpoint

iii. Center

iv. Quadrant

v. Intersection

vi. Perpendicular

vii. Tangent

c) Follow this exercise to demonstrate the use of some of the most commonly used

Osnaps.

To Draw the Triangle

Command:LINE

From point: (pick a point in the middle of the drawing area)

To point: @15,0

To point: FROM

_from Base point:MID

_mid of : (pick a point near the middle of the line)

: @0,75

To point: C (to close)

To Draw the Vertical Line

Command:LINE

Figure 3.24


41/44

E2004/3/41


From point:MID

_mid of : (pick point near the middle of the triangle base)

To point: @0,-100

To point:

To Draw the Horizontal Line

Command:LINE

From point: FROM

_from Base point:MID

_mid of : (pick a point near the middle of the vertical line)

: @-25,0

To point: @50,0

To point:

To Draw the Circle

Command: CIRCLE

3P/2P/TTR/:INT

_int of:(pick a point near the intersection of the two lines)

Diameter/ : 12.5

To Trim the Lines within the Circle

Command: TRIM

Select cutting edges: (Projmode = UCS, Edgemode = No extend)

Select objects: (pick the circle on its circumference)

Select objects:

/Project/Edge/Undo: (pick one of the two lines within the

circle)

/Project/Edge/Undo: (pick the other line within the circle)

/Project/Edge/Undo:

To Draw the Text

Command:DTEXT

Justify/Style/:J


42/44

E2004/3/42


Align/Fit/Center/Middle/Right/TL/TC/TR/ML/MC/MR/BL/BC/BR:M

Middle point: CEN

_cen of : (pick a point on the circumference of the circle)

Height : 15

Rotation angle : 0

Text:N

Text:

Command:

d) Follow the step carefullyi. Begin a New drawing. Turn ON the Snap ( F9 ) and Grid( F7 ). Draw

twocircles, each with a 1.5 unit radius. The circle centers are at 3,5 and

5,5 See Figure 3.24

Figure 3.24

ii. UseZoom All. Does the display change? Now use Zoom Extents. What

happens? Now useZoom Allagain. Which option always showns all the

limits?

iii. Draw a circle with the center at 10,10 and with a radius of5. now use

Zoom All. Notice the Grid only appears on the area defined by the limits.

Can you move the cursor to 0,0? Now useZoom Extents. What happens?

Can you move the cursor to 0,0?

iv. Erase the largecircle. UseZoom All. Can you move the cursor 0,0? Use

Zoom Extents. Can you find point 0,0?


43/44

E2004/3/43


e) Open the file C:\Program files\AutoCAD R14\Sample\azimuth.dwg. The drawing

looks like the following figure

Figure 3.25:Azimuth.dwg File

Using Zoom and Pan command, please show how the figures below look.

Figure 3.26

Figure 3.27

Figure 3.28


44/44

E2004/3/44


FEEDBACK TO SELF ASSESSMENT

Discuss your answers with your lecturer

e2004_computer aided design 1_unit3

Documents