e-ttl ii auto flash for canon™ -...
TRANSCRIPT
BEFORE USING YOUR NEW PRODUCT, PLEASE READ THESE INSTRUCTIONS TO PREVENT ANY DAMAGE.
E-TTL II AUTO FLASH FOR CANON™PT-DFLEXT1C
USER GUIDE
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 1 Wednesday, August 20, 2014 3:27 PM
2
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 2 Wednesday, August 20, 2014 3:27 PM
PT-DFLEXT1CE-TTL II Auto Flash for Canon
ContentsWelcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Back view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5LCD panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setting up your flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Installing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Attaching and removing the flash . . . . . . . . . . . . . . . . . . . . . . . . . . .8Turning on the flash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Using Auto Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Using your flash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Fully automatic flash shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Using E-TTL II autoflash in the shooting modes. . . . . . . . . . . . . .11Using the Flash Exposure Lock (FEL) . . . . . . . . . . . . . . . . . . . . . . . .12Using the High-speed Sync. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Using bounce flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Creating a catchlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Using ZOOM to set the flash coverage . . . . . . . . . . . . . . . . . . . . . .15Using the wide angle panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Using manual flash (M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Using stroboscopic (multi) flash . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Calculating the shutter speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Using second-curtain sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Using S1/S2 slave triggering mode . . . . . . . . . . . . . . . . . . . . . . . . .20
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Legal notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23One-year limited warranty - Platinum . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
WelcomeCongratulations on your purchase of a high-quality Platinum product. Your PT-DFLEXT1C auto flash represents the state-of-the-art in automatic electronic flash design and is designed for reliable and trouble-free performance.
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 3 Wednesday, August 20, 2014 3:27 PM
Important safety instructions1 Read these instructions.2 Keep these instructions.3 Heed all warnings.4 Follow all instructions.5 Do not use this apparatus in the water.6 Clean only with a dry cloth.7 Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.8 Do not store near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.9 Only use attachments/accessories specified by the manufacturer.10 Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
11 To reduce the risk of fire or electric shock, do not expose this device to rain, moisture, dripping, or splashing, and objects filled with liquids, such as vases, shall be placed on it.
FeaturesPackage contents
• E-TTL II Auto Flash• Mini stand• Protective carrying bag• User Guide• Quick Start Guide
3
4
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 4 Wednesday, August 20, 2014 3:27 PM
Front view
# Item Description
1 Built-in wide angle panel and white reflector card
Use the wide angle lens to spread the flash light over a wider angle or to reduce its direct intensity. Pull out the white reflector card with the flash head pointed up to create a more diffused light and a catchlight in a subject's eye for portrait shots. See “Creating a catchlight” on page 14.
2 AF-assist beam emitter Projects a red light beam to help the camera focus in darker settings.
3 Optic slave sensor Detects light from a camera’s built-in flash or other flash source to trigger the flash.
4 External power port Plug an external high-power battery pack or other external power supply into this socket to supplement the flash’s internal batteries. Can also be used instead of the internal batteries.
5 Power port cover Covers and protects the external power port.
6 Mounting foot Connect to the camera’s hot shoe to mount and connect the flash on the camera.
7 Flash head Provides the light (flash) for the photograph.
8 Tripod mount socket Use with the flash in slave mode to mount the flash to a tripod or similar device.
9 PC sync terminal cover Covers the PC sync terminal.
10 PC sync terminal Connect a PC sync cord (not included) to this jack to control the flash remotely.
11 Locking knob Tighten this knob to secure the flash to the camera.
12 Contacts Provides electrical contact to a camera’s hot shoe.
10
11
12
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 5 Wednesday, August 20, 2014 3:27 PM
Back view
# Item Description
1 Bounce angle indicator Indicates the angle of head tilt, when used for bounce flash. See “Using bounce flash” on page 14.
2 LCD panel Displays setting and status information. See “LCD panel” on page 6.
3 ZOOM button Press to zoom the flash head out or in. See “Using ZOOM to set the flash coverage” on page 15.
4 MODE button Press to change the flash mode. See “Using E-TTL II autoflash in the shooting modes” on page 11.
5 Press once to light the LCD panel.
6 / Press to select the previous or next item. Also press to decrease or increase the setting.
7 button Press to select or set an option.
8 / button Press to set high-speed sync (FP flash) (see “Using the High-speed Sync” on page 13) or the second curtain sync (see “Using second-curtain sync” on page 20).
9 Battery compartment cover Slide open to install or replace the batteries.
10 Flash-ready indicator/TEST button
Lights red when the flash is ready to use. Press to fire a test flash.Caution: Do not look closely at the flash window or point it at someone’s eyes at close range.
11 Power switch Slide to the right to turn the flash on. Slide to the left to turn the flash off.
10
11
5
6
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 6 Wednesday, August 20, 2014 3:27 PM
LCD panel
# Item Description
1 M/Multi Indicates whether manual (M) or multi-flash (Multi) is selected.
2 TTL Indicates that the flash is in E-TTL mode.
3 Indicates that the high speed sync (FP flash) is enabled.
4 Indicates that the second-curtain sync is enabled.
5 X/XXX Indicates the manual flash output level.
6 XX+XX Hz • Multi-flash count indicator.• Multi-flash frequency indicator.• Manual flash output indicator in 1/3 stop increments.• FEC - Flash exposure compensation level.
7 S1 Indicates that the S1 slave triggering mode is enabled.
8 S2 Indicates that the S2 slave triggering mode is enabled.
9 Indicates the battery is low. Immediately replace the batteries.
10 Meters scale Indicates the flash distance range of the current setting, in meters.
11 Flash range scale Lights to indicate the current flash range.
12 (manual zoom) Indicates that the zoom must be set manually.
13 Zoom focal length Indicates the current zoom setting of the flash. Matches the lens focal length setting in E-TTL mode.
14 Aperture Indicates the current aperture setting of the camera.
15 Feet scale Indicates the flash distance range of the current setting, in feet.
TTLMulti
0.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm F
Hz1/188 88 88
188 88
+S1 S2
1312
10 11
14 15
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 7 Wednesday, August 20, 2014 3:27 PM
Setting up your flashInstalling the batteries
1 Open the battery compartment cover by pressing it with your thumb, sliding the compartment down, then lifting it open.
2 Insert four (4) AA batteries (not included). Make sure that the + and – match what is indicated in the compartment.
Cautions• Using AA batteries other than Alkaline or NiMH may
cause improper battery contact due to the irregular shape of the battery contacts.
• If you change the batteries after firing many flashes continuously, be aware that the batteries might be hot.
Notes• Make sure that all four batteries are the same brand and
type.• When replacing the batteries, replace all four at one
time.• Batteries are not included with this flash.
7
8
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 8 Wednesday, August 20, 2014 3:27 PM
3 Close the battery compartment cover and slide it into place.
Attaching and removing the flash1 Turn the camera and the flash off.2 With the flash facing toward the front of the camera, slide the flash’s mounting
foot all the way into the camera’s hot shoe.
3 Rotate the locking knob on the mounting foot until it’s tight. Do not overtighten.
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 9 Wednesday, August 20, 2014 3:27 PM
4 Make sure that the camera and flash are turned off, then remove the flash from the camera by loosening the locking knob and sliding it off of the camera’s hot shoe.
Turning on the flash1 Slide the power switch to ON. The flash begins charging. The flash zoom
mechanism also resets. This generates some movement sounds and is normal.
2 When the flash-ready indicator turns red, the camera flash is fully charged and ready for firing.
Using Auto Power OffTo save battery power, if the flash is not used for 90 seconds the power turns off automatically when attached to a camera, or mounted on its stand or a tripod. When the flash is in S1/S2 slave triggering mode, the flash enters sleep mode after 30 to 60 minutes (adjustable). To turn the flash on again, press the camera’s shutter button halfway, or press the flash’s TEST button.
Note
If the battery icon blinks on the LCD panel, the battery power is low and the flash stops charging. Change the batteries immediately.
Note
To test the flash, press the TEST button.
CautionDo not look closely at the flash window or point it at someone’s eyes at close range.
Caution
When the power switch is set to ON and the flash power has automatically turned off, power is still being consumed. Long-term power discharge damages batteries, so make sure to slide the power switch to OFF if the flash will not be used for an extended period.
9
1
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 10 Wednesday, August 20, 2014 3:27 PM
Using your flashFully automatic flash shootingSetting the camera's shooting mode to P (Program AE) or (Full Auto) makes automatic shooting as easy as normal AE shooting.
1 Set the flash to ETTL auto flash mode by pressing the MODE button repeatedly until “TTL” is displayed on the LCD panel.
2 To focus the camera, press the shutter button halfway. The shutter speed and aperture is displayed in the camera viewfinder. Make sure that the icon is shown in the camera viewfinder.
3 Make sure that the subject is within the effective range (indicated by the lighted bars on the flash range scale) displayed on the flash LCD panel.
Before the shot is recorded by the camera, the flash fires a pre-flash. This is immediately followed by the main flash.
Note
“TTL” is displayed on the LCD panel even if the camera is compatible with E-TTL.
TTL
0.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm F35 56
60 5.0
TTL
0.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm F35 56
0
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 11 Wednesday, August 20, 2014 3:27 PM
Using E-TTL II autoflash in the shooting modesSet the camera’s shooting mode to Tv (shutter-priority AE), Av (aperture-priority AE), or M (manual) to use E-TTL II autoflash.
* 1/X seconds is the camera’s maximum flash sync speed.
Mode Description
Tv Select this mode when you want to set the shutter speed manually.The camera automatically sets the aperture, matching the shutter speed, to obtain a standard exposure.
Av Select this mode when you want to set the aperture manually.The camera automatically sets the shutter speed, matching the aperture, to obtain a standard exposure.If the background is dark (like a night scene), a slow sync speed is used to obtain a standard exposure of both the main subject and background.Standard exposure of the main subject is obtained with the flash, while a standard exposure of the background is obtained with a slow shutter speed.Note: Since a slow shutter speed is used for low-light scenes, use of a tripod is recommended.
M Select this mode if you want to set both the shutter speed and aperture manually.Standard exposure of the main subject is obtained with the flash. The exposure of the background is obtained with the shutter speed and aperture combination you set.
Mode Shutter Speed Setting Aperture Setting
AUTO Automatic Automatic
P Set automatically (1/60s - 1/Xs*) Automatic
Tv Set Manually (30s - 1/Xs*) Automatic
Av Set automatically (30s - 1/Xs*) Manual
M Set manually (bulb 30s - 1/Xs*) Manual
11
1
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 12 Wednesday, August 20, 2014 3:27 PM
Using the Flash Exposure Lock (FEL)The FE (flash exposure) lock locks the correct flash exposure setting into the flash for any part of the scene you select.
1 Set the flash to ETTL auto flash mode by pressing the MODE button repeatedly until “TTL” is displayed on the LCD panel, then focus on the subject.
2 Place the selected subject in the center of the viewfinder, then press the FEL button on the camera. If your camera does not have an FEL button, press the
button on the flash. The camera flash fires a preflash and the required flash output for the subject is retained in memory.
“FEL” is displayed in the camera’s viewfinder for 0.5 seconds.Each time you press the FEL button, a preflash is fired, a new flash exposure setting is locked into memory.
Notes• If the TTL mode is not selected, the FE lock cannot be set.• If the subject is too small, the FE lock might not be very
effective.• If the subject is too far away and underexposure is
possible, the blinks in the camera’s viewfinder. Move closer to the subject and try the FE lock again.
*
2
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 13 Wednesday, August 20, 2014 3:27 PM
Using the High-speed SyncBy using the high-speed sync (FP flash), the flash can synchronize with all shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.
• Press the / button repeatedly until the high-speed sync icon is displayed on the flash LCD panel, indicating that the high speed sync function is enabled on the flash.
Notes• Make sure that the icon is visible in the camera’s
viewfinder.• If you set a shutter speed that is the same as or slower
than the camera’s maximum flash sync speed, is not displayed in the viewfinder.
• With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
• To return to normal flash, press the / button. The icon disappears.
• Multi flash mode cannot be set in high-speed sync mode.
TTL
0.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm F35 56
13
1
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 14 Wednesday, August 20, 2014 3:27 PM
Using bounce flashBy pointing the flash head toward a wall or ceiling, the flash bounces off of the surface before illuminating the subject. This can soften shadows behind the subject for a more natural-looking shot. This is called bounce flash.
• Hold the flash head and turn it to the angle you want.
Creating a catchlightWith the white reflector card, you can create a catchlight (a light source that causes a specular highlight) in the subject’s eyes to add life to their facial expression.
1 Point the flash head upward 90°. 2 Pull out the wide angle panel on the front of the flash head. The white
reflector card comes out at the same time.
Notes• If the wall or ceiling is too far away, the bounced flash
might be too weak and may result in underexposure.• The wall or ceiling should be a plain, white color for high
reflectance. If the bounce surface is not white, the surface color may affect the picture.
270
90
4
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 15 Wednesday, August 20, 2014 3:27 PM
3 Push the wide angle panel back in, leaving the white reflector card out.
4 Hold the flash head and turn it to the angle you want.
Using ZOOM to set the flash coverageThe flash coverage can be set, automatically or manually, to match the lens focal length from 24 mm to 105 mm. Also, with the built-in wide angle panel, the flash coverage can be expanded for 14 mm wide-angle lenses.
1 Set your camera to manual zoom. (manual zoom) appears on the flash LCD panel.
2 Press the ZOOM button until the Zoom value blinks on the LCD panel.
3 Press the - or + buttons to change the flash coverage. If the manual zoom is not turned on the flash coverage is set automatically.
Notes• Point the flash head straight ahead or upward by 90°.
The catchlight does not appear in the subject’s eyes if you swing the flash head left or right.
• For maximum catchlight effect, stay approximately 4.9 ft (1.5 m) away from the subject.
Notes• If you set the flash coverage manually, make sure that it
covers the lens focal length so that the picture does not have a dark periphery.
• If you use a commercially-available PC sync cord to connect the camera to the flash’s PC terminal, set the flash zoom manually.
• If the LCD panel displays Zoom mm, the effective focal length cannot be shown. This means that the flash head failed to zoom and the ZOOM button does not work in this case.
TTL
0.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm F35 56
15
1
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 16 Wednesday, August 20, 2014 3:27 PM
Using the wide angle panelUse the wide angle panel to spread light over a wider angle or to reduct its intensity.
1 Pull out the wide angle panel on the front of the flash head. The white reflector card comes out at the same time.
2 Push the white reflector card back in, leaving the wide angle panel out.3 Pivot the wide angle panel down over the flash head. The flash coverage is
extended to 14 mm.
Notes• If you use bounce flash with the wide angel panel in
place, the subject is illuminated by both the bounce flash and direct flash, which may look unnatural.
• Pull out the wide angle panel gently. Using excessive force may detach the wide panel from the flash head.
• The ZOOM button does not work with the wide angle panel in place.
6
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 17 Wednesday, August 20, 2014 3:27 PM
Using manual flash (M)The flash output is adjustable from full power to 1/128th power in 1/3rd step increments. Use a hand-held flash meter to determine the required flash output to obtain a correct flash exposure when using manual flash.
1 Press the MODE button repeatedly until the M is displayed on the LCD panel.
2 Press the SET button to set the flash output. The flash output blinks on the LCD panel.
3 Press the - button to set a lower value, or the + button to set a higher value.4 Press the SET button again to lock the settings.5 Press the shutter button halfway to see the effective flash range displayed.
Using stroboscopic (multi) flashUsing stroboscopic flash, a rapid series of flashes is fired. This can be used to capture multiple images of a moving subject in a single photograph.
You can set the firing frequency (number of flashes per second, expressed as Hz), the number of flashes, and the flash output.
1 Press the MODE button repeatedly until “Multi” is displayed on the LCD panel.
0.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm F35 56
1/128M
0.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm35
1/ 16Multi Hz12
17
1
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 18 Wednesday, August 20, 2014 3:27 PM
2 Press the SET button to select the first item. The flash repeat rate or frequency (the number of flashes per second) blinks on the LCD panel).
3 To set the multi-flash count (the number of flash actuations), press the - or + to select the number of flashes.
4 Press SET button. The next item to be set (the flash power level) starts blinking.
5 To set the flash power level, press the - or + to select the power level. 6 Press the SET button. You can select 1/4, 1/8,1/16,1/32,1/64, or 1/128.
Calculating the shutter speedDuring stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.
Number of flashes / Firing frequency = Shutter speed
For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the shutter speed should be at least 2 seconds.
Caution
To avoid overheating and damaging the flash head, do not use stroboscopic flash more than 10 times in succession. After 10 times, allow the camera flash to rest for at least 15 min. If you try to use the stroboscopic flash mode more than 10 times in succession, the firing might stop automatically to protect the flash head. If this happens, allow the camera flash to rest for at least 15 min.
10 100.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm35
1/128Multi Hz
8
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 19 Wednesday, August 20, 2014 3:27 PM
Maximum stroboscopic flashes
Notes• Stroboscopic flash is most effective with a highly
reflective subject against a dark background.• Use of a tripod, a remote switch, and an external power
source is recommended.• A flash output of 1/1 or 1/2 cannot be set for
stroboscopic flash.• Stroboscopic flash can be used with bulb mode on the
camera.
Hz
Flash Output
1/4 1/8 1/16 1/32 1/64 1/128
1 Hz 7 14 30 60 90 99
2 Hz 6 14 30 60 90 99
3 Hz 5 12 30 60 90 99
4 Hz 4 10 20 50 80 99
5 Hz 4 8 20 50 80 99
6-7 Hz 3 6 20 40 70 90
8-9 Hz 3 5 10 30 60 80
10 Hz 2 4 8 20 50 70
11 Hz 2 4 8 20 40 70
12-14 Hz 2 4 8 20 40 60
15-19 Hz 2 4 8 18 35 50
20-50 Hz 2 4 8 16 30 40
60-99 Hz 2 4 8 12 20 40
19
2
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 20 Wednesday, August 20, 2014 3:27 PM
Using second-curtain sync With second-curtain sync, using a slow shutter speed, you can create a light train following the subject, in which the flash fires right before the shutter closes.
• Press the / button. The second curtain sync icon is displayed on the LCD panel.
Using S1/S2 slave triggering modeThis flash unit supports slave triggering mode. To enter S1/S2 mode from the main mode, press and hold the MODE button until S1 displays. If you are in S1 mode, press the MODE button to enter S2 mode. If you are in S2 mode, press the MODE button to return to master mode. S2 disappears from the LCD panel.
The flash output setting in slave triggering mode is the same as that in manual mode. After pressing the SET button, the flash output blinks. Press the - button or + button to set a value.
You can use your mini stand to set the flash away from the camera in S1 or S2 slave trigger mode.
1 Slide the flash hot shoe onto the mini stand.2 Rotate the locking knob on the mounting foot until it’s tight. Do not
overtighten.3 Place the flash in the location you want.
S1 slave triggering modeIn this mode, the flash unit functions as a slave flash for creating multiple lighting effects. It should be used in manual flash mode. In S1 mode, the flash unit fires at the same time as the master flash fires.
Notes• Second-curtain sync works well in the camera's “bulb”
mode.• With E-TTL, two flashes are fired even at slow shutter
speeds. The first flash is only the preflash, not a malfunction.
• Stroboscopic flash cannot be set.
TTL
0.5 0.7 1 1.5 2 3 4 6 9 13 18
1.7 2.3 4 5 7 10 15 20 30 40 60
m
ft
Zoom mm35
0
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 21 Wednesday, August 20, 2014 3:27 PM
S2 slave triggering modeThis mode is also called “Preflash Cancel.” In this mode, the flash unit ignores a single “preflash” from the master flash and only fires in response to the second, actual flash from the master. Therefore, this mode can be used when using a TTL master flash on the camera.
Troubleshooting
Notes• Slave triggering modes are not supported: when
“red-eye reduction” function is initiated by the master flash (either camera pop-up flash or external on-camera flash) and when the master flash uses the modeling flash function.
• In either slave triggering mode the flash output level is only manually adjustable.
Problem Solution
The flash does not charge • Make sure the batteries are installed in the correct direction.• If appears and blinks on the LCD panel, replace the batteries immediately.• Install the batteries even when using an external power source.
The flash does not fire • Make sure the flash's mounting foot is securely connected to the camera's hot shoe.• Wait until the flash is fully charged and the flash ready indicator lights red.• Make sure the electrical contacts on the mounting foot and hot shoe are clean.• Make sure the camera's flash is turned on.• If the flash ready indicator does not light, replace the batteries.• If appears and blinks on the LCD panel, replace the batteries immediately.• If the flash is used in slave mode, make sure that the master flash on the camera is
turned on and active.
The power turns off by itself • When the flash is set as the master unit, the flash enters sleep mode after 90 seconds of inactivity. Press the shutter button halfway or press the TEST button to wake it up.
• When the flash is set as the slave unit, the flash enters sleep mode after 30 minutes of inactivity. Press the TEST button to wake it up.
Auto zoom does not work • Make sure the flash is not set to manual zoom mode.• Make sure the flash's mounting foot is securely connected to the camera's hot shoe.• If appears and blinks on the LCD panel, replace the batteries immediately.
The picture is underexposed or overexposed
• If there is a highly reflective object (such as glass or a mirror) in the picture, use the FE lock.
• If you are using the high-speed sync, make sure that the subject is within the effective flash range displayed.
• If you are using Manual Flash mode, set the flash to TTL or modify the flash output. Make sure that the flash exposure compensation is set to zero.
Photos have dark corners or only parts of the target subject are illuminated
• Check the flash coverage you set. This flash unit has flash coverage between 24 and 105 mm (lens focal length), which fits medium-format cameras. Pull the wide panel out to extend the flash coverage.
21
2
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 22 Wednesday, August 20, 2014 3:27 PM
SpecificationsSpecifications are subject to change without notice.
Guide No. (at ISO 100, in meters/feet)
Compatible cameras Canon EOS series cameras (E-TTL II autoflash)
Guide No. 58/190 (at 105mm focal length, ISO 100 in meters/feet)
Flash coverage 24-105mm (14mm with wide angle panel)-Auto zoom (flash coverage set automatically to match the lens focal length and image size)-Manual zoom-Rotating/tilting flash head, 0° - 270° horizontally and -10° - 90° vertically (bounce flash)
Flash duration 1.2ms or shorter
EXPOSURE CONTROL
Exposure control system E-TTL autoflash, manual flash
FE lock Via the FEL button or button on the camera
High-speed sync Yes
Stroboscopic flash 1-99 Hz
Optic slave triggering S1 and S2
FLASH RECYCLING (WITH AA ALKALINE BATTERIES)
Recycling time Normal flash approximately 0.1 to 5 seconds
Flash-ready indicator Red indicator light
AF - ASSIST BEAM
Effective range (approx.) 2.3-20 ft. (0.7-6m)
POWER SOURCE
Internal power 4 AA Alkaline or Ni-MH batteries
Battery life (approx. flash count)
100-700 flashes (with AA alkaline batteries)
Power saving Powers off after about 1.5 min. of inactivity
COLOR TEMPERATURE 5600±200k
DIMENSIONS (HxWxD) 4.4 × 3.3 × 6.1×4.4 in. (112 × 83 × 15 mm)
WEIGHT 13.9 oz. (395 g) (flash only, excluding batteries)
Flash coverage (focal length in mm)
14 24 28 35 50 70 80 105
Normal flash (full output)
15/49.2
28/91.9
30/98.4
39/127.9
42/137.8
50/164
53/173.9
58/190.3
*
2
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 23 Wednesday, August 20, 2014 3:27 PM
Manual Flash
Legal noticesFCC Part 15This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply within the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.• Consult the dealer or an experienced radio/TV technician for help.
FCC warningChanges or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user’s authority to operate this equipment.
Flash output Flash coverage (focal length mm)
14 24 28 35 50 70 80 105
1/1 15/49.2
28/91.9
30/98.4
39/127.9
42/137.8
50/164
53/173.9
58/190.3
1/2 10.6/34.8
19.8/65
21.2/69.6
27.6/90.7
29.7/97.4
35.4/116.1
37.5/121
41/134.5
1/4 7.5/24.5
14/45.9
15/29.2
19.5/64
21/68.9
25/82
26.5/86.9
29/95.1
1/8 5.3/17.4
9.9/32.5
10.6/34.6
13.7/45.2
14.8/48.6
17.7/58.1
18.7/61.4
20.5/67.3
1/16 3.8/12.5
7/23
7.5/24.6
9.7/32
10.5/34
12.5/41
13.3/43.6
14.5/47.6
1/32 2.7/8.9
4.9/16.1
5.3/17.4
6.9/22.7
7.4/24.3
8.8/28.9
9.4/30.8
10.3/33.8
1/64 1.9/6.2
3.5/11.5
3.8/12.5
4.9/16
5.3/17.4
6.3/20.7
6.6/21.7
7.3/24
1/128 1.3/4.3
2.5/8.2
2.7/8.9
3.5/11.4
3.7/12.1
4.4/14.4
4.7/15.4
5.1/16.7
23
2
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 24 Wednesday, August 20, 2014 3:27 PM
4
E-TTL II AUTO FLASH FOR CANON™
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 25 Wednesday, August 20, 2014 3:27 PM
One-year limited warranty - PlatinumDefinitions:The Distributor* of Platinum branded products warrants to you, the original purchaser of this new Platinum-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).For this warranty to apply, your Product must be purchased in the United States or Canada from a Best Buy brand or Future Shop brand retail store location or www.bestbuy.com or www.bestbuy.ca or www.futureshop.ca that are packaged with this warranty statement.
How long does the coverage last?The Warranty Period lasts for 1 year (365 days) from the date you purchased the Product. Your purchase date is printed on the receipt you received with the Product.
What does this warranty cover?During the Warranty Period, if the original manufacture of the material or workmanship of the Product is determined to be defective by an authorized Platinum repair center or store personnel, Platinum will (at its sole option): (1) repair the Product with new or rebuilt parts; or (2) replace the Product at no charge with new or rebuilt comparable products or parts. Products and parts replaced under this warranty become the property of Platinum and are not returned to you. If service of Products or parts are required after the Warranty Period expires, you must pay all labor and parts charges. This warranty lasts as long as you own your Platinum Product during the Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the Product.
How to obtain warranty service?If you purchased the Product at a Best Buy or Future Shop retail store location, please take your original receipt and the Product to any Best Buy or Future Shop store. Make sure that you place the Product in its original packaging or packaging that provides the same amount of protection as the original packaging. If you purchased the Product from a Best Buy or Future Shop online web site (www.bestbuy.com, www.bestbuy.ca, or www.futureshop.ca), mail your original receipt and the Product to the address listed on the web site. Make sure that you put the Product in its original packaging or packaging that provides the same amount of protection as the original packaging.To obtain warranty service, in the United States call 1-888-BESTBUY, Canada call 1-866-BESTBUY for FutureShop call 1-800-663-2275. Call agents may diagnose and correct the issue over the phone.
Where is the warranty valid?This warranty is valid only in the United States and Canada at Best Buy or Future Shop branded retail stores or websites to the original purchaser of the product in the county where the original purchase was made.
What does the warranty not cover?This warranty does not cover:• Customer instruction/education• Installation• Set up adjustments• Cosmetic damage• Damage due to acts of God, such as power surges• Accident(s)• Misuse• Abuse• Negligence
25
2
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 26 Wednesday, August 20, 2014 3:27 PM
• Commercial purposes/use, including but not limited to use in a place of business or in communal areas of a multiple dwelling condominium or apartment complex, or otherwise used in a place of other than a private home.
• Modification of any part of the Product, including the antenna• Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in).• Damage due to incorrect operation or maintenance• Connection to an incorrect voltage or power supply• Attempted repair by any person not authorized by Platinum to service the Product• Products sold “as is” or “with all faults”• Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.)• Products where the factory applied serial number has been altered or removed• Loss or Theft of this product or any part of the product• Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly illuminated)
grouped in an area smaller than one tenth (1/10) of the display size or up to five (5) pixel failures throughout the display. (Pixel based displays may contain a limited number of pixels that may not function normally.)
• Failures or Damage caused by any contact including but not limited to liquids, gels or pastes.REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. PLATINUM SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS. PLATINUM PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.Contact Platinum:For customer service please call 800-499-3964*Distributed by Best Buy Purchasing, LLC7601 Penn Avenue South, Richfield, Minnesota, U.S.A. 55423-3645© 2014 BBY Solutions, Inc.All rights reserved. PLATINUM is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.
6
The Pt logo is a registered trademark of Best Buy and its affiliated companies.PLATINUM trademark of Best Buy and its affiliated companies.Registered in some countries. Distributed by Best Buy Purchasing, LLC7601 Penn Ave South, Richfield, MN 55423 U.S.A.©2014 Best Buy. All rights reserved.Made in China.
V1 ENGLISH14-0804
PT-DFLEXT1C_14-0804_MAN_V1_ENG.fm Page 28 Wednesday, August 20, 2014 3:27 PM