e-tender - madhya pradesh skill development mission

e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs

of Sagar Zone

TENDER SPN NO: JDSD-SGO/SP/TEN/2015-16/ 01

FOR THE YEAR

2015-2016

OFFICE OF THE JOINT DIRECTOR

SKILL DEVELOPMENT (ITIs) – SAGAR ZONE

Khurai Road, SAGAR – 470002 (MP)

Phone 07582-266814, E-Mail: [email protected], Website: www.mpdt.nic.in

http://www.mpdt.nic.in/

[I]

Table of Contents

1. Tender Notice (NIeT) ............................................................................................................................................ 1

2. Tender Rules ............................................................................................................................................................. 3

2.1. Scope of Tender ......................................................................................................................................... 3

2.2. Eligibility Criterion .................................................................................................................................. 3

2.3. Earnest Money Deposit (EMD) ........................................................................................................... 4

2.4. Validity of Tender ..................................................................................................................................... 4

2.5. Preparation and submission of Tender ........................................................................................... 4

2.6. Tender Prices ............................................................................................................................................. 5

2.7. Deviation ...................................................................................................................................................... 5

2.8. Opening of Tenders ................................................................................................................................. 5

2.9. Evaluation of Tenders ............................................................................................................................. 5

2.10. Award of Contract .................................................................................................................................... 6

2.11. Placement of Purchase Orders and Delivery Requirements .................................................. 6

2.12. Quality Testing Requirements: ........................................................................................................... 7

2.13. Payment Terms ......................................................................................................................................... 7

2.14. Settlement of Disputes ........................................................................................................................... 7

3. E-TENDERING PROCESS ...................................................................................................................................... 8

3.1. Registration of Bidders on e-Procurement System .................................................................... 8

3.2. Digital Certificates .................................................................................................................................... 8

3.3. Set Up of Bidders' Computer System ................................................................................................ 9

3.4. Publishing of N.I.T. ................................................................................................................................... 9

3.5. Key Dates and time .................................................................................................................................. 9

3.6. Downloading of the Tender Documents ......................................................................................... 9

3.7. Payment for registration on E-tendering portal .......................................................................... 9

3.8. Payment of tender document fee ....................................................................................................... 9

3.9. Preparation of Bids and Submission of Online Bids by the Bidders.................................... 9

3.10. Submission of Earnest Money Deposit ......................................................................................... 10

3.11. Opening of Tender ................................................................................................................................ 10

3.12. Contact Details ........................................................................................................................................ 10

e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone

Joint Director Skill Development – Sagar Zone

Pag

e1

1. Tender Notice (NIeT)

e-Tender Notice

The Joint Director, Skill Development (ITIs) – Sagar Zone, Woman ITI Campus,

Khurai Road, SAGAR – M.P. Invites online bids (Two bid system) from Manufacturers or

Authorized dealers for Supply of Tools, Equipment's and Machines for ITIs of Sagar Zone as

below :

Tender No

Description Earnest Money

Deposit Bid Document

Price

01 Mechanical & Electrical Machine INR 100000 INR 1000

2. Online bidding go through https://www.mpeproc.gov.in and online e-tenders are

invited as per key dates from Manufacturers or their Authorized Dealers for Supply of

Tools, Equipment's and Machines for ITIs of Sagar Zone Madhya Pradesh. Tender

document and other details are also available at the websites

https://www.mpeproc.gov.in, www.tender.gov.in and www.mpdt.nic.in

3. In all respect the hard copy of the Bids (Envelope-A along with Earnest money, and

Envelope-B) must be received at the office of the undersigned latest by 3:00 PM on

19/01/2016 and will be opened ONLINE Technical Tender (Envelope-A) on the same day

i.e. 19/01/2016 at 4:00 PM. In the presence of such tenderer or their authorized

representatives as may be present.

4. All corrigendum/ amendments/changes if any will only be issued and made available only

on https://www.mpeproc.gov.in.

(Sunil Choudhary)

Joint Director

Skill Development(ITIs)Sagar



Pag

e2

Key Dates and Time

SN Task Date & Time

1. ONLINE BID DOCUMENT

PURCHASING END DATE 19/01/2016, 12:00 HRS

2. BID CLOSING FOR SUBMISSION

ON ONLINE BIDS 19/01/2016, 14:00 HRS

3.

SUBMISSION OF HARD COPY OF

BIDS (Envelope – A along with

EMD, and Envelope – B)

20/01/2016, 15:00 HRS

4. ONLINE OPENING OF THE

TECHNICAL BIDS 20/01/2016, 16:00 HRS

5. ONLINE OPENING OF THE

FINANCIAL BIDS 25/01/2016, 12:00 HRS

Note: Soft copy (In prescribed Excel & Word Format) and Hard Copy of the Bid should be same, if in

case of any difference/discrepancy Soft Copy will be considered.



Pag

e3

2. Tender Rules

Scope of Tender

The Joint Director, Skill Development (ITIs) – Sagar Zone, Woman ITI Campus Khurai Road, SAGAR

– M.P. (hereinafter referred as Tender Inviting Authority and/or Tender Acceptance Authority

and/or Ordering Authority unless the context otherwise requires) Invites online bids (Two bid

system) from Manufacturers or Authorized dealers for Supply of Tools, Equipment's and Machines

for ITIs of Sagar Zone as below :

Tender

No Description

Earnest Money

Deposit

Bid Document

Price

01 Mechanical & Electrical Machine

INR 100000 INR 1000

Eligibility Criterion

The Tenderers should fulfil the following eligibility criteria:

a) The Tenderer should be Manufacturer or Authorized Dealer having relevant Licence of

Manufacturer/ Authorized Dealer and such a Registration should be valid as on the date

of Tender submission. as per Annexure -2

b) The Tenderer should have achieved annual turnover as follows (every FY) in the last

three financial years, backed by practicing chartered accountant.

Tender

No Description Minimum Annual Turnover

01 Mechanical & Electrical Machine

100 Lakhs

c) The Tenderer (and tenderer’s principal manufacturer, if tenderer is Authorized Dealer)

should not be blacklisted either by the Tender Inviting Authority or by any State

Government or by Government of India. An undertaking by the tenderer should be

submitted in this regard certifying that the tenderer or its principal manufacturer (if

applicable) is eligible to participate in the bid process. as per Annexure.4(Compliance of

Tender)

d) The Manufacturer should be in the business of manufacturing of similar equipment for a

period not less than 5 Years.

e) The Tenderer should furnish the information on past 2 years supplies and satisfactory

performance inAnnexure – 3.

f) The Tenderer must submit the latest Sales Tax/VAT Tax clearance certificate.

g) The Tenderer must submit the Form –“A” on letterhead with signature &

stamp.Annexure-1



Pag

e4

Earnest Money Deposit (EMD)

a) All tenders must be accompanied with Tender-wise EMD (Hard Copy) along with

Technical (Physical) bid.

b) The EMD should be submitted in the form of Demand Draft of Nationalized

Bank/Scheduled Bank in Favour of “Joint Director, Skill Development, (ITI's)Sagar

Zone” Payable at Sagar. Earnest Money submitted in any other form will not be

accepted and the tender will be rejected.

c) Earnest Money/Security Deposit to this office in previous tenders will not be adjusted

towards the present tender and no request will be entertained in this regard.

d) Industries registered as Small scale industrial units with the Director of Industries,

Government of Madhya Pradesh, Bhopal only will be exempted from depositing the

Earnest money; however they should send a true copy of the certificate for claiming the

above exemption. Firms registered with the Director General of Supplies and Disposals

and small Scale Industrial Units registered with Central Govt. or with other State

Government are not exempted from depositing earnest money.

e) The EMD shall be refunded to the unsuccessful tenderer after finalization of the contract. It

shall be refunded to the successful tenderer on receipt of the performance security deposit.

f) The EMD will be forfeited, in case Tenderer withdraws its Tender during the validity of

bids OR the successful bidder who fails to sign the contract agreement.

Validity of Tender

a) The Tender will be valid for a period of 12 Months after the due date of submission of

Tenders. A Tender valid for a shorter period shall be rejected by the Tender Inviting

Authority as non-responsive

b) In exceptional circumstances, prior to the expiration of the Tender validity, the Tender

Inviting Authority may request the Tenderers to extend the Tender validity for further

period as deemed fit. The request and the responses thereto shall be made in writing. A

Tenderer may refuse the request without forfeiting its EMD. A Tenderer, agreeing to the

request will not be required or permitted to modify its Tender.

Preparation and submission of Tender

a) The Tender should be Computerised and every correction and interlineations in the bid

should be attested with full signature by the tenderer, failing which the bid will be

treated as ineligible. Corrections done with correction fluid should also be duly attested.

b) Bidder should give all relevant particulars about every item, such as maker’s name

Country of Manufacture and Specifications and Price etc.

c) Articles for which rate contracts are available with the D.G.S.& D. Government of

India, New Delhi. The bidder should enclose the copy of the rate contract agreement

along with the tender.

d) Authorized dealer should submit the certificate from its manufacturer as proof to

purchase supplied items from OEM.

e) All documents/papers should be numbered, signed and sealed by the Tenderer on each

page.

f) The Tender is required to be prepared and submitted in two parts viz. ‘Part A -

Technical Bid’ and ‘Part B - Price Bid’.

g) The ‘Envelope of Part-A Technical Bid’ shall contain all essential documents for

Technical Tender. Such documents attached as per Annexure-8 to (Online & Physical).



Pag

e5

h) The ‘Envelope of Part-C- Financial Bid’ shall contain duly filled, stamped and signed

Price Schedule in the format provided in Annexure – 5.

i) The Online tenders as above should be submitted on www.mpeproc.gov.in as per

Scheduled date and time.

j) Tender submitted or received after the closing date and time will not be considered and shall

be returned to the Tenderer unopened.

Tender Prices

a) Tender has been called for in the names of Items. The Tenderers should quote the rates

for the Items mentioned in Annexure – 10. The composition and Specification of each

item should be as per details given in Annexure – 10.

b) The Tenderer should mention the name of manufacturer of the item being quoted.

c) The rates should be quoted in format of Price Schedule shown in Annexure-5. Rates quoted

in any other format tender will be rejected.

d) Rates inclusive of Excise Duty, Customs duty, transportation, insurance, and any

incidental charges, but exclusive of State VAT/CST should be quoted for each of the

required item, separately on door delivery basis (FOR Destination, at Stores) as per

format of Price Schedule given in Annexure – 5.

e) Quoted rates are valid up to one year from the date of signing of contract agreement

and shall be firm during the currency of the contract.

Deviation

If the Tenderer submits the offer with deviation for any item then Deviation statement

should be submitted for every offer. In the absence of this the purchaser reserves the right

to accept or reject the bid of that particular item. Bidder should submit Deviation statement

as per Annexure-9. No other formats will be accepted. In absence of deviation statement the

tender will be rejected.

Opening of Tenders

a) The Tenders shall be opened at the scheduled date, time and venue by the committee

constituted by the Tender Inviting Authority. The Tenderers’ representative may

attend the Tender opening.

b) Technical Bid shall be opened first Online and the envelopes containing Technical Bid

along with EMD shall be opened physically.

c) The date and time of opening of Price Bid shall be informed to all such Tenderers who

qualify in technical Bid evaluation. The tenderer’s representative may choose to attend

the opening of Price Bid.

d) In the event, the date of opening as above is declared government holiday; the tenders

shall be opened at the same time on the next working day.

Evaluation of Tenders

a) The purchase committee, constituted by the Tender Inviting Authority, shall evaluate

the tender with reference to technical requirements and various other commercial

criteria given in the Tender Document.

http://www.mpeproc.gov.in/



Pag

e6

Award of Contract

a) Security Deposit to the extent of 5% of the total value of the order in the form of

FDR/Bank Guarantee (in Performance Security Form- as per Annexure-7) will have to

be deposited by the successful Bidder before the final orders are placed with him.

Security Deposit should be submitted in favour of the Joint Director Skill

Development (ITI's) Sagar Zone Woman ITI Campus Khurai Road Sagar M.P.If the

demanded security deposit to the extent of 5% is not deposited by the bidder in the

specific period the Earnest Money already deposited with the tender is liable to be

forfeited.

b) Bid Security should have the validity period of 16 months.

Placement of Purchase Orders and Delivery Requirements

a) The Tender Inviting Authority shall place individual Purchase Orders for supply of

Items during the period of 1 year from the date of award of contract with successful

Tenderer(s). Tender Inviting Authority reserves the right to extend the validity of

purchase order further by 3 months on the same rates and terms & conditions of the

contract.

b) The supplier should complete the supply at the respected Govt. Industrial Training

Institute(ITI) situated at various location of Sagar Zone within 45 days from the date of

issue of purchase order.

c) If at any time the Tenderer has, in the opinion of the Tender inviting authority, delayed

the supply of Items due to one or more reasons related to force Majeure events such as

riots, mutinies, wars, fire, storm, tempest or other exceptional events, the time for

supplying the Items may be extended by the Tender inviting authority/ordering

authority at its discretion for such period as may be considered reasonable. However

such extension shall be considered only if a specific written request is made by the

Tenderer within 7 days from the occurrence of such event. The exceptional cause does

not include scarcity of raw material, power cut and labour disputes.

d) According to the M.P. Store Purchase Rules, 30% of total purchase will be made from

that Manufacturer/Authorized Dealer/Firm who has more than 50% partnership of the

persons belonging to SC/ST category. If the Manufacturer/Authorized Dealer/Firm who

has more than 50% partnership of the persons belonging to SC/ST category does not

participate in the tender then purchaser will call the list of such

Manufacturer/Authorized Dealer/Firm from the District Industries Centre (DIC) and

may place the order up to the 30% value of tender to the eligible SC/ST firms on the

accepted lowest rates.

e) The undersigned reserves the rights for any changes/cancellation/rejection of any part

or whole tender, without assigning any reason what so ever.

f) Warrantee/Guarantee should be for a period of minimum 1 year.

g) All consignment must be dispatched freight paid to concern ITI “To pay” Railway

Receipt/Freight Receipts will not be accepted. Loading /Unloading charges shall be

borne by the supplier.

h) It must be noted that normally all correspondence and transactions will be made only

with the parties whose tenders have been accepted and not with anybody else.

i) The undersigned reserves the right to split up the order for supply of articles at tender

for amongst more than one tender.



Pag

e7

Quality Testing Requirements:

a) The Tender inviting authority may ask for samples and demonstration of any particular

item quoted by the bidders. The bidders shall have to submit samples and give

Demonstration in the prescribed time limit. In case the samples are not produced in the

prescribed time it shall be open to the undersigned to forfeit Earnest Money Deposited

by the bidder.If the samples sent by the party are approved the same will be adjusted in

regular supply and in the case of rejection, they will be returned back to the party at his

cost.

b) The Items including its packing (packaging), to be supplied, shall be of the best quality

and shall comply with the specifications given in the Tender Document.

c) All Items should be supplied with quality certificate. The undersigned may get the items

inspected by such person or persons he deems fit and to reject such of these items as in

his opinion do not come up to the specification. The decision of the undersigned will be

final in such cases. The rejected items will be returned on the bidder’s cost.

d) If any of the Items supplied by the tenderer, found to be ‘Not of Standard Quality’ after

the delivery, the tenderer should supply the whole Item quantity again irrespective of

consumption of that particular. The balance stock, if any, should be taken back within 7

days by the supplier at his/her own cost otherwise the authority will destroy it and no

claim in this regard shall be entertained.

e) Guarantee Certificate: - The Bidder will have to submit the GUARANTEE CERTIFICATE

as per Annexure – 6. Warrantee/Guarantee should be for a period of minimum 1 year.

Payment Terms

a) The 90% payment shall be released within 30 days from the date of receipt of accepted

Items and upon submission of claim for payment supported by Invoice (in triplicate),

and remaining 10% after successful working of item in duration of 2 months. However,

if supplied Items are found not as per specifications, then whole payment will be

withheld and shall be released only after receipt of replacement of Items which were

found not of standard quality.

Settlement of Disputes

a) In the event of any dispute arising out of the tender or orders such dispute would be

subject to the jurisdiction of Courts of Madhya Pradesh nearest to the place of Tender

Inviting Authority.



Pag

e8

3. E-TENDERING PROCESS

Registration of Bidders on e-Procurement System

Manufacturers or their Authorized Dealers for Supply of Tools, Equipment's and Machines for ITIs

of Sagar Zone are required to register on the e-Procurement System on the website

https://www.mpeproc.gov.in in order to participate in tenders processed by Directorate of Skill

Development using E-Procurement system of IT department.

E-tendering Helpdesk at TCS, Bhopal Tel. No.18002588684

Digital Certificates

The Bids submitted online should be signed electronically with a Class III Digital Certificate to

establish the identity of the bidder submitting the bid online. The Bidders may obtain Class III

Digital Certificate issued by an approved Certifying Authority authorized by the Controller of

Certifying Authorities, Government of India. A Class III Digital Certificate is issued upon

receipt of mandatory identity proofs along with an Application Form. Only upon the receipt of

the required documents, a Digital Certificate can be issued. For details please visit

www.ccc.gov.in

Please note that it may take upto 7 working days for issuance of Class III Digital

Certificate, hence the bidders are advised to obtain them at the earliest.

The Bidders may obtain more information and the Application Forms required to be

submitted for the issuance of Digital Certificate from the e -Procurement, IT

Department, Arera Hills, and Bhopal.

E-tendering Helpdesk at TCS, Bhopal Tel. No.18002588684.

E-mail :- [email protected]

Important Note

Bid for a particular tender can be submitted during the ONLINE BID SUBMISSION stage only using the

Digital Certificate that is used to encrypt the data during the ONLINE BID PREPARATION.

In case, during the process of a particular tender, the bidder looses his Digital Certificate because of any

problem (such as misplacement, virus attack, hardware problem, operating system problem, etc.); he

may not be able to submit his bid online. Hence, the bidders are advised to keep their Digital

Certificates in a safe place under proper security.

The digital certificate issued to the Authorized User of a Partnership firm / Private

Limited Company / Public Limited Company / Joint Venture and used for online bidding

will be considered as equivalent to a no-objection certificate / power of attorney of that

user.

In case of Partnership Firm, majority of the Partners have to authorize a specific

individual through Authority Letter signed by majority of the Partners of the firm.

In case of Private Limited Company, Public Limited Company, the Managing Director /

any other Person (having designated authority to authorize a specific individual) has to

authorize a specific individual through Authority Letter.

Unless the certificate is revoked, it will be assumed to represent adequate authority of

the specific individual to bid on behalf of the Organization for online tenders as per

Information Technology Act, 2000. This Authorized User will be required to obtain a

mailto:[email protected]



Pag

e9

Digital Certificate. The Digital Signature executed through the use of Digital Certificate of this

Authorized User will be binding on the firm. It shall be the responsibility of

Management/Partners of the concerned firm to inform the Certifying Authority, if the

Authorized User changes, and apply for a fresh digital certificate for the new Authorized User.

Set Up of Bidders' Computer System

In order for a Bidder to operate on the e-Procurement System, the Computer System of the

Bidder is required to be set up for Operating System, Internet Connectivity, Utilities, Fonts,

etc. A help file on setting up of the Computer System can be obtained from e-Procurement Cell

(M/s. TCS Limited, 5th Floor Corporate Block, DB Mall, Bhopal).

Publishing of N.I.T.

For the Tenders processed using the e-Procurement System, only a brief Advertisement

related to the Tender shall be published in the newspapers and the Detailed Notice and terms

and conditions of tender shall be published only on the e-Procurement System. The bidders can

view the Detailed Notice, Terms & Conditions of tender document and the time schedule for all

the Tenders processed using the e-Procurement System on the website

https://www.mpeproc.gov.in

Key Dates and time

The Bidders are strictly advised to follow the time schedule (Key Dates and time) of the

tender for their side of tasks and responsibilities to participate in the tender, as all the

stages of each tender are locked before the start time and date and after the end time and

date for the relevant stage of the tender as set by the concerned Department Official.

Downloading of the Tender Documents

The tender documents can be downloaded online from the website https://www.mpeproc.gov.in. All

the Bidders are required to register on the e-Procurement System of IT Department of Madhya

Pradesh website https://www.mpeproc.gov.inin order to participate in tender.

Payment for registration on E-tendering portal

The registration fee Rs. 500/- + taxes applicable is to be paid ONLINE. And details of payment

are required to email on [email protected] , [email protected],

[email protected]

Payment of tender document fee

Although the tender document can be downloaded from the website http://www.mpeproc.gov.in,

the bidder has to pay a sum of INR 1000 (Rupees One Thousand only) towards tender document fee

by way of Online.

Preparation of Bids and Submission of Online Bids by the Bidders

The Bidders have to prepare their Bids online, encrypt their bid data in the bid forms and

submit documents required to be uploaded related to the tender as per the time schedule

mentioned in the key dates and time as given in the Notice Inviting Tender after signing of the

same by the Digital Signature of their authorized representative.

https://www.mpeproc.gov.in/






Pag

e10

Submission of Earnest Money Deposit

The manufacturers or their Authorized Dealers shall submit their Earnest Money Deposit as usual in a

physically sealed Earnest Money Deposit envelope and the same should reach the concerned office

as stated in the Notice Inviting Tender and key dates.

Earnest Money should be submitted in the form of Demand Draft of Nationalized Bank/Scheduled

Bank in Favour of “Joint Director, Skill Development, (ITI's)Sagar Zone”Sagar MP.

The manufacturers or their Authorized Dealers has to upload scanned copy of Earnest

Money Deposit instrument along with the reference details in the relevant field during online

bidding.

Opening of Tender

The concerned Department Official receiving the tender or his duly authorized person shall open

the online.

For any further queries, bidders may kindly contact

For more details, please contact on working days within working hours (10:30 to 17:30)

Tel. No. 07582-266814, Mob. 9425477550

E-tendering Helpdesk at TCS, Bhopal Tel. No. 18002588684

E-mail:- [email protected]

FORMAT OF COVERING LETTER

Ref No: …………………………………….. Date: …………………………….

To,

The Joint Director

Skill Development, (ITI's)

Woman ITI Campus Khurai Road,

Sagar-470002

Sub: Submission of Supply of Tools & Equipment for ITIs of Sagar Zone, Tender SPN No. JDSD-

SGO/SP/TEN/2015-16/01

Dear Sir,

As per terms & conditions of the tender following documents are submitted as under:

1. Form “A” Enclosure No. …………………….

2. EMD

Tender No

Earnest Money Deposit

DD No Date Issuing Bank

01 INR 100000

3. Other Testimonials …………………

We have quoted rates for items (Number of quoted item to be mentioned) in the Tenders as stated

below:

Tender No

Total Item in Tender Enquiry

No of Item Quoted

01

The entire item is quoted with brand name & full specification. The technical detail as desired is

submitted in prescribed format as per enclosed Annexure

Authorized Signatory

Name & Signature with Seal

Date

Annexure-1

FORM – A

(To be signed and returned along with the tender)

Ref No: …………………………………….. Date: …………………………….

To,

The Joint Director



Sagar-470002


SGO/SP/TEN/2015-16/01

Dear Sir,

I/We

Name of Authorized Signatory

Name of Bidder

Address of Bidder

Phone

e-Mail

Have read the Tender rules for the supply of various goods as per Tender notice to the Industrial

Training Institutes in Sagar Zone and I/We accept all rules for Tender.



Date

Annexure - 2

MANUFACTURERS' AUTHORIZATION FORM

Ref No: …………………………………….. Date: …………………………….

To,

The Joint Director



Sagar-470002

Dear Sir,

We who are established and reputable manufacturers of (name and description of goods

offered) having factories at (address of factory) do hereby authorize M/s (Name and address of

Agent) to submit a bid, and sign the contract with you for the goods manufactured by us against the

Tender Published by you.

Yours faithfully

(Name)

(Name of manufacturers)

Note: This letter of authority should be on the letterhead of the manufacturer and should be

signed by a competent person. This AUTHORIZATION FORM should be notarized. It should be

attached in the bid.

Annexure – 3

PROFORMA FOR PERFORMANCE STATEMENT

(FOR THE PERIOD OF LAST TWO YEARS)

Tender SPN NO JDSD-SGO/SP/TEN/2015-16/01

Date of Opening

Name of Bidder

Name & Address of Purchaser

Order No & Date

Description & Quantity

of order item

Order Value

(in Rs)

Date of Delivery

Actual Delivery

Date

Reason of delay in delivery (if any)

Attach satisfaction Certificate issued by Purchaser

1 2 3 4 5 6 7 8



Date

Annexure - 4

(COMPLIANCE OF TENDER (AFFIDAVIT)

(To be submitted by the BIDDER on stamp paper duly notarized)

I/We, M/s. ___________________________________ represented by its Proprietor/Managing Partner / Managing Director having as Registered Office at _____________________________________andits factory premises at _____________________________________ do declare that I / We have carefully read all the conditions of Tender in Ref. No. __________________ for supply of Tools, Equipments and Machines floated byJoint Director, Skill Development (ITIs) – Sagar Zone, Woman ITI Campus Khurai Road, SAGAR – M.P, and accepts all terms and conditions of tender. I / We agree that the Deptt. forfeiting the Bid security and or Performance Security Deposit and debarring / black listing me / us for a period of 2 years , if any information furnished by us proved to befound false, misleading, malafide at any time or during the inspection and not complying the tenderconditions & specifications. I /We hereby declare that, we have not been debarred / penalized by any Govt. Departments/ neither Undertaking nor our marketing Assistance has been stopped / withdrawn in the past. We hereby extend our full guarantee and warrantee as per Terms & Conditions of the above tender for goods & services offered by us. We hereby declare that we will be held fully responsible for any mischief/misconduct or supply of substandard items by us or our dealer/distributor. We also confirm to provide the spares for at least five years from the date of supply / installation. We reiterate that goods ordered on the above firm shall be supplied in due time.

Seal Signature:

Name & address:

to be attested by the Notary:

Annexure-5

PRICE SCHEDULE (To be fill in prescribed Excel format only & same to be upload for Price Bid, should be submit Separate Sheet for each Tender)

Tender SPN NO JDSD-SGO/SP/TEN/2015-16/01

S.No Item

Code

Name &

Specification

of Item

Make Price for each unit (in Rs.)

Unit Price

Including

Excise/

Custom Duty

(if any)

Service

Tax (if

any)

Inland transportation,

insurance, Installation

and other local costs

incidental to delivery

Total price

inclusive of

a+b+c (Rs. in

figure)

Sales

Tax/VAT/CST

(if any)

Total Unit

priceinclusive

of all(Rs. in

figures)

Total unit price

inclusive of all (Rs.

in words)

(a) (b) (c) (a+b+c)=d (e) (d+e) (f)



Date

Annexure - 6

GUARANTEE CERTIFICATE

(On the original letter head of the manufacturer)

Ref No: …………………………………….. Date: …………………………….

To,

The Joint Director

Skill Development,


Sagar-470002


SGO/SP/TEN/2015-16/01

Ref: Your S.O.NO. ……………… Dated: …………….placed on our Authorized Dealer

M/s ……………………………………………………………………………………………………………………………………….

Dear Sir,

With reference to the above, this is to certify that the following item has been supplied by

our Authorized Dealer M/s …………………………………………………………………………

SN Item Name & Description QTY

1

2

We further certify that the material supplied as above has been duly pre inspected by us and have

been found to be in conformity with specification as per the terms & conditions of the supply order.

They are hereby guaranteed for a period of 12 months from the date of receipt at respective ITI;

against any material defects, manufacturing defects (Including assembly installation, commissioning

as applicable) and bad workmanship.

In case of any defect, we guarantee to replace the same immediately without at any cost.

Seal & Signature of Dealer

Seal & Signature of Manufacturer

CC: Principal, Govt. ITI ……………………………………………..

Annexure-7

PERFORMANCE SECURITY FORM

To, …………………………………………………………………………………………

( Name of Purchaser )

WHEREAS

………………………………………………………………………………………………………………

………………………………………………………………

( Name of Supplier )

hereinafter called “ The Supplier” has undertaken , in pursuance of Contract No. ………………Dated

……………. 2016 … to supply (Description of Goods) hereinafter called “The contract.” AND

WHEREAS it has been stipulated by you in said contract. That the supplier shall furnish you with a Bank

Guarantee by a recognized bank for the sum specified there in as security for compliance with the

supplier’s performance obligations in accordance with the contract. AND WHEREAS We have by affirm

that we are Guarantors and responsible to you on behalf of the supplier, up to a total of ( Amount of the

Guarantee in Words and Figures ) and we undertake to pay you , upon Your first written demand

declaring the supplier to be in default under the contract and without cavil or agreement, any sum of sums

within the limits of ( Amount of Guarantee ) aforesaid , without Your needing to prove or to show grounds

or reasons for your demand or the sum specified there in.

This Guarantee is valid until the …………Day of ………………2016

Note- Stamp Paper of Bank Guarantee should be purchased by Bank.

Signature and seal of the Guarantors

( Bank Authorities )

…………………………………….........

………………………………………

………………………………………

Date …………………………….

Address ………………………….

…………………………………….

……………………………………..

Annexure - 8

CHECK LIST ENVELOPE – A

SN Documents Submitted

Y/N

Page No

1. Duly filled Checklist as per format given in Annexure – 8.

2. EMD in form Demand Draft of Nationalized Bank/Scheduled Bank in Favour of “Joint Director, Skill Development,(ITI's) Sagar”

3. Covering Letter duly signed & stamped on letter head.

4. Form – A duly signed & stamped on letter head

5. Self-attested copy firm registration Certificate

6. Self-attested copy of registration in Commercial/sales tax department and its TIN number.

7. Item Wise Authorization Certificate in case of Authorized Dealer Annexure – 2.

8. Latest Sales/VAT tax clearance certificate.

9. Latest Income Tax clearance certificate.

10.

Declaration of not having been debarred/blacklisted either by the Tender Inviting Authority or by any State Government or by Government of India on INR 100 Judicial Stamp. Compliance of Tender (affidavit) Duly Notarized as par Annexure – 4.

11. Audited Balance sheet and Profit and Loss Statement of last three financial years.

12. Annual turnover statement of last three financial year backed by practicing chartered accountant.

13.

Self-attested copy of relevant Licence for Manufacturing/Selling and distribution (whichever appropriate) of the product quoted duly approved by the Licensing authority for each schedule of product quoted as per specification in the tender.

14. No Deviation Certificate.Annexure – 9.

15. Catalogue of Items.

16. Performance statement as per the formatAnnexure – 3.



Date

Annexure-9

No Deviation Certificate

Tender No.- -----

S.No. Specification of

Machine/Equipment

mentioned in

Tender Enquiry

Specification of

Machine/Equipment

offered by the

Bidder

Whether there

are deviation

from the tender

specification

Yes/No

If yes,

indicate the

deviation &

whether it is

on +ve side &

how



Date

Annexure – 10

List of Items (01 Mechanical & Electrical Machine)

SN Item Code Item Name Specifications Indicative

QTY

1. WEL57 Power saw machine

14’’

Power hacksaw machine Power hacksaw machine

Cutting Capacity

( Round ) : 250

( Square ) : 200

( Flat ) : 250 X 75

Blade : 450

Motor H.P. (1440 RPM) : 1.5

' V ' Belt : B 56 X A 34

Floor Space : 500 X 1350

Height : 975

5

2. WEL41 Welding Transformer

or Invertors with all

accessories ( 300A ,

OCV 60 ± 100 V, 60%

duty cycle)

Welding Transformer or Invertors with all accessories ( 300A

, OCV 60 ± 100 V, 60% duty cycle) 2

3. FIT175 SS and SC centre lathe

(all geared) with

minimum specification

as: Centre height 150

mm and centre

distance 1000 mm

along with 3 & 4 jaw

chucks, auto feed

system, safety guard,

taper turning

attachment, motorized

coolant system,

lighting arrangement

& standard

accessories.

Capacity- : Height of centre 150mmCentre

distance 1200mmSwing over bed.

350mmSwing over cross slide 200mmSwing in gap

530mmWidth of gap 150mmWidth of bed

280mmHead stock- :Spindle nose standard A2-

5Spindle bore 42mmSpindle taper

METRICSpindle speeds nos . 16Speed range forward

30-1200RPM.Speed range reverse 30-1200RPMFeeds

& threads-:No. of longitudinal 40/0.06 to

2mm/rev feed / range 40/0.06 to

2mm/revNo. of cross feed / range 40/0.014-

0.44mm/revScrew of range1. Metric 40/0.5 to

10mm pitch 2. Inch. 40/2 TO 60 T.P.I.3.

Module 30/0.25 TO 3.254. D.P. 30/8

TO 120Tools or top slide -:Top slide travel

105mmCross slide travel 215mmLeast count

of graduation 0.2mm longOn hand wheels for carriage ,

0.5mm top slide Cross slide and top slide.Max. shank section

of tool 25 x 25mmTail stock-: Tail stock sleeve taper

MT- 3 Sleeve travel (manual) 140 mmSleeve

diameter 50 mm min.Graduation of sleeves

collar 1 div.= mmOffset on tail stock (max.) 5.0 mm

on either sideAcces.-:Independent chuck 300 mm , 3 jaw self –

centering chuck 250 mm , fixed steady , travelling steady

faceplate , driving plate , 4 way tool posts , quick change gear

box for metric or British threads, live & dead centers with

taper attachments all geared head stock type

2

4. FIT176 Drilling machine pillar

sensitive 0-20 mm cap

Drilling machine pillar sensitive 0-20 mm cap with swivel

table motorised with chuck & key. Precision Heavy Duty Pillar 1


QTY

with swivel table

motorised with chuck

& key.

Drill Machine,Cap: 20 mm, Spindle traveling – 125 mm,with

standard accessoriesOptional:® Drill Vice® Drill Chuck,

Arbor® ISI electric motor, Switch and V belt

5. FIT177 Drilling machine bench

sensitive 0-12 mm cap

motorised with chuck

and key.

Drilling machine bench sensitive 0-12 mm cap motorised with

chuck and key.Sensative drilling machine pilliar type 12mm

Extra Accessories:

. ISI Make electric motor, Switch and V belt.

. Drill Vice

. Drill Chuck

Drill Bit set 3 mm to 12 mm set of 10 pcs.

7

6. FIT33 Portable hand drill

(Electric) 0 to 6 mm

Electrical drill portable machine

Drilling dia in wood : 15 mm

Drilling dia in steel : 6.5. mm

Power input : 350 w

No-load speed : 4000 rpm

Weight : 1 . 1 kgs

5

7. DM35/MMV

39

Car Jet washer with

standard accessories

Single plunger car washer with 3 HP moter and 12 mtr hose

and two guns, working pressure 25 Kgs, discharge per gun24

LPM

4

8. MMV42 Chain Pulley Block-3

ton capacity with

tripod stand

Chain Pulley Block (TRIPLE SPUR GEAR GRADE - 80) WITH 3

MTR CHAIN

CAPACITY 3 TON with tripod stand

2

9. MMV72 Disk brake with caliper

assembly

Disk brake with caliper assemblyThe Model is made out of

Orginal parts such as Two Brake disc, two Caliper assembly

(onesectioned), master cylinder etc, the model is mounted on

a sturdy iron frame and can bedemonstrated by operating the

lever provided.

4

10. MMV237 Drilling machine bench

to drill up to 12mm dia

along with accessories

Drilling machine bench to drill up to 12mm dia along with

accessories 1

11. FIT179 D.E. pedestal Grinding

machine with 200mm

diameter wheels rough

and smooth with twist

drill grinding

attachment.

PEDESTAL GRINDER

HP 1.0 KW 0.75 PH 3 HZ 50

AMP 1.6 VOLT 415 RPM 2800

Complete with Grinding Wheel

Size: 200 x 25mm x 19.05 mm ( Original bore 31.75 MM) ,

fitted with Eye Shield, Starter, Wheel Guard, And

WHEEL CENTRE DIST. : 460MM

CENTRE HEIGHT : 940MM

EXTRA :

DRILL GRINDING ATTACHMENT (UPTO 19MM)

3

12. DM191/MM

V241

Grinding machine

(general purpose) D.E.

pedestal with 300 mm

dia wheels rough and

PEDESTAL GRINDER DIRECT DRIVEN WITH INBUILT MOTOR

MOUNTED ON C.I. PEDESTAL STAND

HP 2.00 KW 1.5 PH 3 HZ 50

AMP 3.5 VOLT 415 RPM 1400

Complete with Grinding Wheel Size :300 X 50 X 31.75 mm

3


QTY

smooth (Original bore 50.8 MM,)(One Coarse & one Medium)

Fitted with Eye Shield, Siemens Starter,

Wheel Guard, & Std Tool Rest Plate

WHEEL CENTRE DIST. : 615MM

CENTRE HEIGHT : 940MM

13. FIT ALL01 Transformer welding

set 150 amps. –

continuous welding

current, with all

accessories and

electrode holder

Transformer welding set 150 amps. – continuous welding

current, with all accessories and electrode holder 3

14. DM202/MM

V260

Welding Transformer (

150-300 Amps)

Welding Transformer ( 150-300 Amps) 5

15. DM166/MM

V199

Timing lighter Timing lighterFor checking and setting ignition timing on

automotive,agricultural and marine engines. Measures

ignition spark advance from 0-60ş. For use on 12V systems.

Reverse polarity protected. Accurate to 8,000rpm. 1m long

removable coiled power leads. Impact resistant metal case

and rubber nose cone. On/off trigger switch. Bright linear

Xenon flash tube for daylight use. Focused lens provides a

concentrated light. Easy to apply inductive impulse pick-up.

Built-in check light.

9

16. DM159/MM

V191

Tandem master

cylinder with booster

Tandem master cylinder with booster This model is made out

of original used parts, will be suitably sectioned to

demonstrate the internal construction details showing the

minute information and the model should be suitably painted

and mounted on a navopan wooden base.

12

17. DM169/MM

V207

Turbocharger cut

sectional view

Turbocharger cut sectional view This model is made out of

original used parts, will be suitably sectioned to demonstrate

the internal construction details showing the minute

information and the model will be suitably painted and

mounted on a navopan wooden base.

3

18. DM171 Universal puller for

removing pulleys,

bearings

Universal puller for removing pulleys, bearings 1

19. DM175/MM

V215

Valve spring

compressor universal.

Valve spring compressor universal. 5

20. DM174/MM

V214

Valve Lifter Valve Lifter 3

21. DM178/MM

V218

Water pump for

dismantling and

assembling

Water pump for dismantling and assembling 12


QTY

22. DM182/MM

V231

Arbor press hand

operated 2 ton

capacity

Arbor press hand operated 2 ton capacity Overall Dimensions

(L x W xH) (In.) 18-1/8 x 10-1/4 x 22-1/2Weight (Lbs.)

108Capacity Over Table (In.) 11/12Anvil Diameter (In.) 6-

11/16 Arbor press hand operated 2 ton Arbour

Press Salient Features 1) Extra Heavy cast Frame Ribbed for

strength2) EN-8 Casehardened with Heavy duty rack teeth3)

Base Hole Adjustable with Bushings to Suit different jobs.* Set

for Dies * Sturdy Accurate and Reliable* Smooth Operation

and Precision WorkmanshipTECHNICAL SPECIFICATIONMax

Pressure exerted Ton 2Centre to Back mm 190Max. height

from Base to Guide mm 381Size of arbour round mm

44Approx. Weight of Press Kg 80Applications :1)

Embossing2) Punching3) Cutting4) Pressing5) Stamping6)

Deep Drawing etc.

3

23. DM183/MM

V232

Automotive exhaust 5

gas analyzer (petrol &

Diesel) or Diesel

Smoke meter

Automotive Exhaust 5 Gas Analyzer-Petrol

1. Measures CO,HC,CO2,O2

2. Engine RPM for Sealed engines

3. Oil Temperature measurement

4. Air Fuel Ratio and Lambda Measurements

5. Option to add Nox measurement facility

6. OMIL Class1 category

7. RS 232 Port

3

24. DM185/MM

V234

Diesel Engine – CRDI -

4 stroke for

Dismantling and

assembling with

swivelling stand

Diesel Engine – CRDI - 4 stroke for Dismantling and

assembling with swivelling stand Diesel Engine -The device

is designed based on latest technology diesel engines with

Common rail direct fuel injection system. The trainer helps to

simulate engine startup, speedup, slowdown and other actions

so as to illustrate the structure and working principle of CRDI

engines.Features 1. Real and operating CRDI Diesel engine,

illustrating the structure and working process.2. Coloured

circuit diagram on the training Module printed on to 6mm

organic glass base..3. Detection terminals for operator to

detect various sensors, actuators, electrical signals for engine

control unit, such as resistive, voltage, current , frequency and

wave form signals are provided on to the printed circuit

diagaram.4. Automobile meters are fitted on to the training

module along with the printed circuit diagram, to

demonstrate engine speed, temperature, fuel pressure,

charging light etc.,5. The training module is fitted with

diagnostic socket (DLC) for universal automobile

decoder(Scan tool) to read fault codes, clear fault codes and

read data stream.6. Fault setting switch bank will be provided

to induce faults in the training module to demonstrate the

fault and to diagnose faults. 7. Good working condition engine

will be provided with fuel tank and battery. Throttle control is

provided on the module to accelerate.8. The training module

is fabricated using steel pipe frame with spray painted for

good looks and the entire setup is provided with caster wheels

with brakes for easy movement of the same.

4


QTY

25. DM186/MM

V235

Diesel engine (

Running condition )

Stationary type

Diesel engine (Running condition)stationary type

The Four stroke Diesel engine setup to be prepared by using

good working condition Single cylinder diesel engine with all

the fittings of the engine along with air filter, fuel tank

,electrical wiring etc., all mounted on to a sturdy iron frame.

3

26. DM203/MM

V263

Working Condition of

Diesel Engine – CRDI -

4 stroke Engine

Assembly with fault

simulation board

Working condition of diesel engine -CRDI-4 stroke engine

assembly with fault simulation board.The device is designed

based on latest technology diesel engines with Common rail

direct fuel injection system. The trainer helps to simulate

engine startup, speedup, slowdown and other actions so as to

illustrate the structure and working principle of CRDI

engines.Features 1. Real and operating CRDI Diesel engine,

illustrating the structure and working process.2. Coloured

circuit diagram on the training Module printed on to 6mm

organic glass base..3. Detection terminals for operator to

detect various sensors, actuators, electrical signals for engine

control unit, such as resistive, voltage, current , frequency and

wave form signals are provided on to the printed circuit

diagaram.4. Automobile meters are fitted on to the training

module along with the printed circuit diagram, to

demonstrate engine speed, temperature, fuel pressure,

charging light etc.,5. The training module is fitted with

diagnostic socket (DLC) for universal automobile

decoder(Scan tool) to read fault codes, clear fault codes and

read data stream.6. Fault setting switch bank will be provided

to induce faults in the training module to demonstrate the

fault and to diagnose faults. 7. Good working condition engine

will be provided with fuel tank and battery. Throttle control is

provided on the module to accelerate.8. The training module

is fabricated using steel pipe frame with spray painted for

good looks and the entire setup is provided with caster wheels

with brakes for easy movement of the same.

4

27. DM189/MM

V238

Dual Magnetization

Yoke : AC / HWDC, 230

VAC, 50Hz

Dual Magnetization Yoke : AC / HWDC, 230 VAC, 50Hz

Magnetic yoke along with Accessories;- a) Copper bulb - 1

nob) Pipe gauge - 1 noc) Manual - 1 no d) Calibration

certificatee) Carrying bagf) Test Bar

5

28. DM193(a)/

MMV244(a)

Hydraulic jack HI-LIFT

type -3 ton capacity

Hydraulic jack HI-LIFT type -3 ton capacity One stroke instant

lift foot pedal, raises the saddle up to jack point to increase

productivity. Constructed from heavy gauge steel. 1m, two

piece handle. 120mm diameter saddle.

Automatic safety overload protection. Positive twist, lock and

release mechanism. Heavy duty rear

swivelling castor wheels.

Maximum load: 3000kg.

Minimum height: 145mm.

Maximum height: 490mm.

3

29. DM193(b)/

MMV244(b)

Hydraulic jack HI-LIFT

type 5 Ton capacity

Hydraulic jack HI-LIFT type 5 Ton capacity

01. Capacity : 5 – Tones

02. Dist. Between Column (FB X LR) : 160 x 400 mm

3


QTY

03. Dist. Between Ram to Bed (Min X Max) : 125 x 500 mm

04. Ram Stroke : 75 mm

06. Type Of Press Frame : ‘H’ frame type fabricated frame

30. DM194/MM

V245

Liquid penetrant

Inspection kit

Liquid penetrant Inspection kit SIZE - (in 280 ml pack) 4

31. DM196/MM

V249

Pipe Bending Machine

(Hydraulic type)

12mm to 30mm

Pipe Bending Machine (Hydraulic type) 12mm to 30mm 5

32. DM197/MM

V250

Pneumatic rivet gun

with standard

accessories

PNEUMATIC RIVET GUN WITH ACCESSORIESTOOL SHANK:

10.2 MM ROUNDPOWER: 7.2 JOULESBLOWS PER MINUTE:

3000 BPMBORE X STROKE: 19 X 67 MMWEIGHT: 1.6

KGLENGTH: 171 MMAIR INLET: ¼”TOOL TO BE SUPPLIED

IN A MOULDED CARRY CASE WITH 5 DIFFERENT TYPES OF

CHIELS, ONE MIMI OILER& ONE QUICK CHANGE RETAINER

8

33. DM199/MM

V252

Tin smiths bench

folder 600 x 1.6mm

Tin smiths bench folder 600 x 24 GAUGE 4

34. DM200/MM

V254

Trolley type portable

air compressor single

cylinder with 45 liters

capacity Air tank,

along with accessories

& with working

pressure 6.5 kg/sq cm

Trolley type portable air compressor 1 single cylinder with 45

liters capacity air tank all accessories and with working

pressure 6.5 kg/sq.cm2

TROLLEY TYPE COMPRESSOR 1 HP, SINGLE PHASE MOTOR

SINGLE STAGE WITH SINGLE PHASE MOTOR

Displacement : 128 LPM

C.F.M : 4.5 CFM

Motor Power Rating : 1 HP

Tank Capacity : 45 LTR

Max Pressure : 8.5Kg/ cm2/121psi

No Of Stage : SINGLE

No Of Cylinder : 1

Overall DIA(L*W*H) : 1230 x 390 x 780

2

35. WEL46 Air compressor

suitable for air plasma

cutting system.

Air compressor suitable for air plasma cutting system :

Compressuer Air pison type(Vehicular), 3HP, 3Phase C.G/ABB

moter-(2.2KW) Two stage with 3 phase moter

displacement:294 LPMCFM: 10.4 CFMMotor power rating:

3HP CG/ABBTan capacity: 90 ltrMax pressure:

12kg/cm2/171psiNo of stage: TWONo. of cylinder: 2Overall

Dia (LxWxH): 1230x445x810

6

36. DM201/MM

V259

Welding plant Oxy-

Acetylene complete (

high pressure)

Welding plant Oxy-Acetylene complete ( high pressure) 5

37. MMV20 AC alternator slip ring

puller

AC alternator slip ring puller 2

38. MMV23 Air Brake Assembly Air Brake Assembly

The model is made out of Original parts such as Air

compressor, Unloader valve, foot valve, Booster, Wheel

2


QTY

assembly, air tank, control valve etc Suitably sectioned and

mounted on a sturdy

iron frame.

39. MMV183(a) Steering assembly -

.Rack & pinion,

Steering assembly - .Rack & pinion, 2

40. MMV183(b) Steering assembly -

Worm & roller

Steering assembly - Worm & roller 2

41. MMV183(c) Steering assembly -

Recirculating ball

Steering assembly - Recirculating ball 2

42. MMV183(d) Steering assembly -

Power steering

Steering assembly - Power steering 3

43. MMV31 Anti theft device Anti theft device 2

44. MMV41 Carburetor repair tool

kit

Carburetor repair tool kit 2

45. MMV50 Coil spring compressor

for suspension spring

Coil spring compressor for suspension springWeight: 5.65

lbsBolt Length (in): 11.25Bolt Material: Heat Tempered CR-

VCase Included: YesCoil Spring Compressor Type:

InternalDrive Size(s): 3/4Maximum Coil Wire Diameter (in):

0.75Maximum Sping Length (in): 12Maximum Spring Inside

Diameter (in): 5.5Minimum Spring Inside Diameter (in):

3.75Minimum Spring Length (in): 5Spring Compressor Detent

Pins: No

2

46. MMV53 Constant Mesh Gear

box with stand for

Dismantling and

assembly.

Constant Mesh Gear box with stand for Dismantling and

assembly

The Gearbox will be of original vehicle accessories, will be

mounted on stand, All the aggregates

will be cleaned and service and Painted with Single Colour

Paint

3

47. MMV58 Cut section working

model of automatic

transmission Gear box

Cut section working model of automatic transmission Gear

box The model is made out of full size original used automatic

transmission of a car, the transmission will be suitably

sectioned to show the internal details,of gear mechanism of

forward and reverse speeds. The automatic shifting of the

gears can be explained using this model clearly. The model

will be mounted on to a tubular frame, Suitable color

imported painting will be carried out along with Miracle

coating for the model will be done for extra gloss and shine.

The painting will be carried out in such a way that different

colors will be use for different components such as

identification of sectioned area etc according to the colors

code for easy identification of different systems and

mechanisms. All the hardware’s and gears will be suitably

electroplated. with appropriate stand and working manual.

2


QTY

48. MMV189 Synchronous Gear box

with stand for

Dismantling and

assembly.

Synchronous Gear box with stand for Dismantling and

assembly

The Gearbox will be of original vehicle accessories, will be

mounted on stand, All the aggregates

will be cleaned and service and Painted with Single Colour

Paint

3

49. MMV55 Cut section Model of

Mock layout of a motor

car ±electrical system

working model

Cut section model of mock layout of a motor car -electrical

system working model cut section This demonstration board

which will give a complete idea of the electrical system of a

car. In this demonstration board the actual wiring with parts

and accessories of a car had been arranged, according to the

electrical circuit of a car and terminals are provided to

connect the battery. By giving connection the working of

individual parts such as Self starter, Alternator, Wiper Motor,

Horn, Head lights, Tail lamps, Parking lamps, Side indicators,

Brake light, Distributor, Sparks of spark plugs, etc., can be

demonstrated. The parts sectioned to show the internal

constructional details. This is a working demonstration model.

with appropriate stand and working manual.

2

50. MMV56 Cut section models of

shock absorbers

Cut section models of shock absorbers: This model is made

out of original used parts, will be suitably sectioned to


minute information, the model will be suitably painted and

mounted on a navopan wooden base.

2

51. MMV57 Cut section of cross ply

and radial tyres

Cut section of cross ply and radial tyres: This model is made

out of original used parts, will be suitably sectioned to


minute information, the model will be suitably painted and

mounted on a navopan wooden base

3


model of centrifugal

clutch assembly.

Cut section working model of centrifugal clutch assembly.This

model is made out of original parts such as Flywheel, Clutch

plates, etc. to demonstrate the working of clutch assembly. By

operating the pedal provided the model can be demonstrated.

The entire model is mounted on a sturdy iron frame

2


model of Diaphragm

clutch assembly.

Cut section working model of Diaphragm clutch assembly.

This model is made out of original parts such as Flywheel,

Pressure Plate ,Clutch plates, etc. to demonstrate the working

of clutch assembly. By operating the pedal provided the model

can be demonstrated. The entire model is mounted on a

sturdy iron frame

2


model of Single plate

clutch assembly.

Cut section working model of Single plate clutch assembly.

This model is made out of original parts such as Flywheel,

Clutch plates, etc. to demonstrate the working of clutch

assembly. By operating the pedal provided the model can be

demonstrated. The entire model is mounted on a sturdy iron

frame

2


QTY

55. MMV65/M

MV66

Demonstration board

of 2W Ignition system,

ignition coil

Demonstration board of 2W Ignition system, ignition coil

DEMONSTRATION BOARD OF IGNITION SYSTEM OF A TWO

WHEELER (WORKING): - This open demonstration-working

unit is made out of original used parts such as switch, ignition

coil, Magneto Assembly, spark plug, with necessary wiring

connections. By switching on the switch and by giving rotation

to the Magneto Assembly, Sequential Sparks in the spark plug

can be demonstrated.

5

56. MMV67 Demonstration board

of MPFI system

Demonstration board of MPFI system -The Instruction board

adopts the real components of electronic fuel injection system

to illustrate engine fuel system structure and working

principle. The components are rigged onto colour circuit

diagram. And made functional.Features1. Real and operatable

engine fuel injection system is assembled onto a colour

printed board to illustrating the structure and working

process .2. Coloured circuit diagram on the training Module

printed on to 6mm organic glass base. Where in the students

can compare the diagram and actual diagram.3. Detection

terminals for operator to detect various sensors, actuators,

electrical signals for engine control unit, such as resistive,

voltage, current , frequency and wave form signals are

provided on to the printed circuit diagram.4. The training

module is fitted with diagnostic socket (DLC) for universal

automobile decoder (Scan tool) to read fault codes, clear fault

codes and read data stream.5. Fault setting switch bank will

be provided to induce faults in the training module to

demonstrate the fault and to diagnose faults.6. Set the line

break, grounding short circuit, improper contact or open

circuit faults can be induced, user can adjust the number and

type of faults. 7. Good working condition Parts will be

provided with fuel tank. The instruction board has to be

connected to 220V AC socket Which changes to 12V DC

internally so that the board works without battery.8. The

training module is fabricated using steel pipe frame with

spray painted for good looks and the entire setup is provided

with caster wheels with brakes for easy movement of the

same.

2

57. MMV73(a) Distributor ±Duel

advance type

Distributor ±Duel advance type 2

58. MMV73(b) Distributor reluctance

type

Distributor reluctance type 2

59. MMV78 Drum brake assembly Drum brake assembly- This model is out of original parts such

as Two Brake drum assembly , one master cylinder wheel

cylinder (One sectioned), Brake Shoes , etc. the model can be

demonstrated by operating the lever provided .

2

60. MMV212 Vacuum assisted

hydraulics brake

assembly with vacuum

Vacuum assisted hydraulics brake assembly with vacuum

booster 3


QTY

booster

61. MMV98 Full floating axle and

semi-floating axle

assembly

Full floating axle and semi-floating axle assembly

This model is made out of original used heavy vehicle parts,

suitably sectioned to show clearly the action of Differential

gear box, such as pinion crown wheel in Differential and Brake

drums in Rear axle, A Crank handle is provided to

demonstrate the model. The model is mounted on a sturdy

iron frame. & This model is made out of original used light

vehicle, suitably sectioned to show the action of Differential

gear box and Brake drums in Rear axle. A Crank handle is

provided to demonstrate the model. The whole model is

mounted on a sturdy iron frame.

2

62. MMV157 Rear axle full floating

type with stand for

Dismantling and

assembly

Rear axle with stand for Dismantling and assembly

The axle will be of original vehicle accessories, will be

mounted on to stand, All the aggregates will be cleaned and

service and Painted with Single Colour Paint

2

63. MMV93 Front axle ( Rzeeppa

Joint) with stand for

Dismantling and

assembly

Front axle ( Rzeeppa Joint) with stand for Dismantling and

assembly The Axle will be of original vehicle accessories, will

be mounted on stand, All the aggregates will be cleaned and

service and Painted with Single Colour Paint

2

64. MMV118 Horn and Horn relay Horn and Horn relay 4

65. MMV179(a) Starter motor axial

type

Starter motor axial type,The Starter Motor will be of original

vehicle accessories, will be mounted on base, All the

aggregates will be cleaned and service and Painted with Single

Colour Paint

2

66. MMV179(b) Starter motor pre-

engagement type

Starter motor pre-engagement type The Starter Motor will be

of original vehicle accessories, will be mounted on base, All

the aggregates will be cleaned and service and Painted with

Single Colour Paint

2

67. MMV179(c) Starter motor Co-axial

type

Starter motor Co-axial type The Starter Motor will be of

original vehicle accessories, will be mounted on base, All the

aggregates will be cleaned and service and Painted with Single

Colour Paint

2

68. MMV203 Tread wear indicator Tread wear indicator 2

69. MMV255 Tube/ tyre vulcanizing

machine

Tube/ tyre vulcanizing machine 2

70. MMV206 Tubeless tyre repair

kit

Tubeless tyre repair kit 3

71. MMV208 Tyre & split rim wheel

assembly

Tyre & split rim wheel assembly 2


QTY

72. MMV219 Wheel cylinder Wheel cylinder 8

73. MMV220 Wiper motor assembly Wiper motor assembly 4

74. MMV223 Working Model of

power windows

Working Model of power windows

This model to be made out of parts, will be suitably sectioned

And Arranged to demonstrate the internal construction

details showing the minute information such as motor and its

gear arrangement etc., and working of the same can be show

by connecting it to a battery, the model will be suitably

painted and The entire model is mounted on a sturdy iron

frame

2

75. MMV224 Working model of

torque converter

Working model of torque converter

This model should be made out of parts, should be suitably

sectioned to demonstrate the internal construction details

showing the minute information, and working of the same, the

model should be suitably painted and mounted on a navopan

wooden base.

2

76. MMV225 4 Point relays 4 Point relays 4

77. MMV226 5 Point relays 5 Point relays 4

78. MMV227 Air bag simulator Air bag simulator The Instruction board adopts the real

components of Air bag system to illustrate Air bag safety

system structure and working principle. The components are

rigged onto colour circuit diagram and made

functional.Features1. Real and operatable Air bag system is

assembled onto a colour printed board to illustrating the

structure and working process .2. The Vehicle Crash is

Simulated by pushing and hitting the crash sensor along the

rail provided to demonstrate the quick air bag inflation.3.

Coloured circuit diagram on the training Module printed on to

6mm organic glass base. Where in the students can compare

the diagram and actual diagram.4. Detection terminals for

operator to detect various sensors, actuators, electrical

signals for engine control unit, such as resistive, voltage,

current , frequency and wave form signals are provided on to

the printed circuit diagram.5. Fault setting switch bank will be

provided to induce faults in the training module to

demonstrate the fault and to diagnose faults. 6. Set the line

break, grounding short circuit, improper contact or open

circuit faults can be induced, user can adjust the number and

type of faults.7. Good working condition Parts will be

provided with fuel tank. The instruction board has to be

connected to 220V AC socket Which changes to 12V DC

internally, so that the board works without battery.8. The

training module is fabricated using steel pipe frame with

spray painted for good looks and the entire setup is provided

with caster wheels with brakes for easy movement of the

2


QTY

same.

79. MMV229 Air conditioning

service Unit (Car)

Air conditioning service Unit (Car)

1.Functions: vacuum,recharging,refrigerant purifying and

recycling,

2.Discharge used oil and refill new oil

3.High pressure and low pressure alarm

4.Empty tank alarm

2

80. MMV230 Air conditioning

trainer kit

Air conditioning trainer kit This model is made out of original

New parts, will be suitably Arranged on to a Metal frame with

navopan board to demonstrate details of Piping connection,

Wiring circuit with all the accessories such as Cooling Coil,

compressor, evaporator, necessary hoses, condenser etc., the

model will be made to work using a FHP motor so that by

operating the AC panel the operation and cooling effect of the

same can be demonstrated, the Model will contain a car

Battery for the operation of the blower and Magnetic clutch

the entire system will be suitably painted.

2

81. MMV239 Four stroke petrol

engine with CNG

setup-working

condition

Four stroke petrol engine with CNG/LPG setup-working

condition The Four stroke petrol engine setup should be

prepared by using good working condition multi cylinder car

engine with all the fittings of the engine along with radiator,

silencer, air filter, starter, battery, alternator, indication

meters, fuel tank ,electrical wiring with ignition switch etc., all

mounted on to a sturdy iron frame with caster wheels (mobile

trolley) . All the fittings such as meter, fuel tank, radiator etc.,

along with the engine should be arrange on to the paint

finished trolley with its original fittings such as rubber

dampers and clamps so as to contain the vibrations. The

wiring for the sensors, indication meters etc, should be done

so that by cranking the ignition the engine should start

working, the indications such as alternator charging, oil

pressure, temperature etc., should be displayed on to the

necessary indication meter attached. The engine assembly

should be serviced ,painted with a single colour paint.

3

82. MMV242 Hand operated

Hydraulic press

HYDRAULIC H - FRAME PRESS (Hand Operated)

01. Capacity : 5 – Tones

02. Dist. Between Column (FB X LR) : 160 x 400 mm

03. Dist. Between Ram to Bed (Min X Max) : 125 x 500 mm

04. Ram Stroke : 75 mm

06. Type Of Press Frame : ‘H’ frame type fabricated frame

2

83. MMV246 MPFI petrol engine

with swiveling stand

along with special

tools for dismantling

and assembling

MPFI petrol engine with swiveling stand along with special

tools for dismantling and assembling

The original car engine will be mounted on to the rolling

stand, so that slowly rolling the handle provided the engine

can be rotated and lock and any position and angle to enable

the students to assemble or dismantle the engine, a large oil

drip pan is provided at the bottom to collect the small screws,

parts and oil dripping. The rotating stand is made out of steel

tube with gears for slow speed operation along with self

2


QTY

retention wheels. The Paint finished rotating stand is

provided with heavy duty caster wheels with brakes.

84. MMV248 Petrol Engine(2-

stroke) Motor

Cycle/Scooter along

with special tools and

accessories

Petrol Engine vertical ( 2 stroke) Motor cycle /

Scooter type 1.5 hp Indian make contemporary model

The petrol engine setup to be prepared by using good working

condition engine with all the fittings of the engine along with

silencer, air filter, fuel tank ,electrical wiring with ignition

switch etc., all mounted on to a sturdy iron frame with caster

wheels (mobile trolley) . All the fittings such as fuel tank, etc.,

along with the engine should be arrange on to the paint

finished trolley with its original fittings such as rubber

dampers and clamps so as to contain the vibrations.. The

engine assembly should be serviced ,painted with a single

colour paint.

1

85. MMV253 Transfer case with

stand for Dismantling

and assembly.

Transfer Case with stand for Dismantling and assembly - The

Axle will be of original vehicle accessories, will be mounted

on stand, All the aggregates will be cleaned and service and

Painted with Single Colour Paint

3

86. MMV256 Two post car lift –

capacity 4000 kg

Electro Mechanical Two Post Lift 3.2 Tons Lifting Capacity

Electro MechanicalUniversal adaptor Input voltage : 380 V, 4

HP

3

87. MMV257 Tyer Changer Machine Tyer Changer Machine--External Locking Rim Dimensions:

300mm-510mm (12″- 20″), Internal Locking Rim Dimensions:

355mm-585mm (14″- 23″), Max Tyre Diameter: 950mm

(37″),Max Tyre Width: 410mm (16″),Bead Breaker Force

(10bar) : 2500Kg, Working Pressure: 8-10bar(116-145Psi),

Power Supply Voltage: 220V (Single Phase)

Internal locking rim dimensions: 355mm-585mm (14"-23")

Max tyre diameter: 950mm (37"),

Max tyre width: 410mm (16"),

Bead breaker force (10bar) : 2500kg,

Working pressure : 8-10bar(116-145psi),

Power supply voltage : 220V (single phase)

2

88. MMV258 Ultrasonic Injection

cleaning equipment

INJECTOR CLEANER & TESTER which can clean and test Auto

engine injectors by simulating engine working conditions. It

can also perform cleaning on the injectors and fuel supply

system on vehicle.

Specifications: Power supply: □AC220V±10%, 50Hz

Main unit power: 200W;

Ultrasonic cleaner power: 100W;

Simulated RPM range: 10～9990rpm; step: 10rpm;

Time range: 1～9999s;

Pulse width: 0.5～25ms; step 0.1 ms;

Fuel tank capacity: 4000ml;

Dimensions: 400mm×410mm×580mm

Feature - * Ultrasonic cleaning: To perform simultaneous

cleaning on several injectors, to remove the carbon deposits

2


QTY

on the injector completely. * Uniformity/Spray ability test: To

test the uniformity of injecting amount of each injector, and to

monitor the spraying

status of each injector with the lighting of backlight. This test

is also for reverse flush.

* Leakage test: To test the sealing and dribbling conditions of

injectors under system pressure. * Injecting flow test: To

check the injecting amount of the injector in 15 seconds of

constant injection. * Auto. test: To test injectors by simulating

different working conditions. * On-vehicle cleaning: The unit

is equipped with various adaptors and couplers that facilitate

cleaning on the injectors on vehicle.

89. MMV261 Wheel alignment

Machine –

computerised 3D

Computerised 3 D Wheel aligner High Precision Dual Camera

Waterproof Targets Real time data reading 10"-24" Solid

Wheel clamps

2

90. MMV262 Wheel balancing

machine

Computerised digital Wheel Balancer with elevated display

panel, automatic Distance Measurement, steel wheel and 7

types of ALU function for rim dia upto 24",supplied along with

Wheel Guard, Mid Centring device & standard Cones

2

91. MMV264 Working Condition of

Petrol MPFI Engine

Assembly with fault

simulation board

Petrol MPFI Engine Assembly with fault simulation board:

Working of Petrol MPFI Engine Assembly with fault

simulation board The device is designed based on latest

technology petrol engines with Multi point fuel injection

system. The trainer helps to simulate engine startup, speedup,

slowdown and other actions so as to illustrate the structure

and working principle of MPFI engines.

Features

1. Real and operating Petrol MPFI engine, illustrating the

structure and working process.

2. Coloured circuit diagram on the training Module printed on

to 6mm organic glass base..

3. Detection terminals for operator to detect various sensors,

actuators, electrical signals for engine control unit, such as

resistive, voltage, current , frequency and wave form signals

are provided on to the printed circuit diagram.

4. Automobile meters are fitted on to the training module

along with the printed circuit diagram, to demonstrate engine

speed, temperature, fuel pressure, charging light etc.,

5. The training module is fitted with diagnostic socket (DLC)

for universal automobile decoder(Scan tool) to read fault

codes, clear fault codes and read data stream.

6. Fault setting switch bank will be provided to induce faults

in the training module to demonstrate the fault and to

diagnose faults.

7. Good working condition engine will be provided with fuel

tank and battery. Throttle control is provided on the module

to accelerate.

8. The training module is fabricated using steel pipe frame

with spray painted for good looks and the entire setup is

provided with caster wheels with brakes for easy movement

2


QTY

of the same.

92. DM199/M

MV253

Discrete Component

Trainer / Basic

Electronics Trainer

Discrete Component Trainer / Basic Electronics Trainer -

Technical Specifications :Inbuilt Variable / Fixed DC Regulated

Power SuppliesOutput voltages : 0-3VDC: 0-30VDC:

+5VDCInbuilt AC Power SuppliesOutput voltages : 10 - 0 -

10VAC/ 500mAGlass Epoxt PCB used as front panel of 270

mm x 170 mm & mounted onlight weight shock proof plastic

cabinetSymbol diagram printed on Glass Epoxt PCB & all

important test Points arebrought out on front panelPower

requirement : 230 VAC 10%, 50Hz.Weight : 2.2 Kg

Approx.Dimensions (mm) : 300( L) x 175(B) x 75(H) List of

Experiments under above Topics : PN Junction Diode V-I

Characteristics Zener Diode V-I Characteristics Voltage

Stabilization of Zener Diode LED Characteristics Resistance in

Series & ParallelCharging & Dischrging of Condensor LCR

Resosnace Circuit Clipping & Clamping Half Wave, Full Wave

& Bridge Rectifier Common Base Transistor Amplifier

Common Emitter Transistor Amplifier Common Collector

Transistor Amplifier RC Coupled Amplifier Basic Logic

GatesRC Passive Filter Circuits Standard Accessories : Power

cable, Patch Chord & Instruction manual

5

93. DM29/MM

V33

Auto Electrical test

bench

1. Motor 2 hp three phase 1500rpm 2. Digital dc voltmeter of

3.5 digital display with minimum readable upto 0.1 volt 3.

Digital dc ammeter for load of 3.5 digit display with minimum

readable upto 1 amp.4. Digital rpm indicator 0-5000 rpm.5.

Speed sensor for sensing starter speed6. Alternator loading

through wire wound resistors of 0-50 amps capacity 5.

Alternator loading through 4nos rotary switches.6. Two

directional rugged mounting arrangement to suit various

range of alternators.7 Provision for two speed check with two

set of pulley and belts8 Starter free spin testing up to 100

amps capacity.9 110 v series lamp test facility also available.1.

Motor 2 hp three phase 1500rpm 2. Digital dc voltmeter of

3.5 digital display with minimum readable upto 0.1 volt 3.

Digital dc ammeter for load of 3.5 digit display with minimum

readable upto 1 amp.4. Digital rpm indicator 0-5000 rpm.5.

Speed sensor for sensing starter speed6. Alternator loading

through wire wound resistors of 0-50 amps capacity 5.

Alternator loading through 4nos rotary switches.6. Two

directional rugged mounting arrangement to suit various

range of alternators.7 Provision for two speed check with two

set of pulley and belts8 Starter free spin testing up to 100

amps capacity.9 110 v series lamp test facility also available.

4

94. ELE107/D

M30/MMV

34

Battery Charger Battery Charger : The Automatic Battery Chargers are

designed for precise charging of lead acid, sealed maintenance

free, VRLA (valve regulated lead acid) and other batteries.

These batteries require a sophisticated charger to charge

them in a precisely regulated fashion specified by the

manufacturer to avoid irreversible damage through gassing

and shortened service life. The Elak Automatic charger meets

the charging specifications of a wide range of VRLA and RG

11


QTY

sealed batteries very accurately. The charger delivers a

measured constant current to the battery until the

manufacturer’s specified maximum battery voltage is attained.

This voltage is then held constant for a specified period to

allow a uniform charge across all the plates. The charger may

be left connected indefinitely to a fully charged battery

without the fear of over-charging or damage.SPECIFICATIONS

-

Voltage - 12 V/ 24 V /

Current 0 -15 A/ 0 -10 A /

End Voltage13.8 V / 14.4 V/ 27.6 V / 28.8 V Size

L x W x H (mm) 340 x 260 x 160 11

95. ELE111 Voltage Stabiliser Voltage Stabiliser- Input: 150 – 230 volt AC, Output: 220 volt

AC

3

96. ELE133(a) Starters for 2 to 5 H.P.

A.C Motors

a. Resistance type

starter

Starters for 2 to 5 H.P. A.C Motors Resistance type- Features:

Slipring Motor Starting by varying resistance through control

knob, Motor full speed run on all resistance cut with interlock

protection, Operated through push button and contactors,

Green Red indicators for Start & Stop the Motor. Dully marked

terminals for Rotar & Stators. Meetring

3

97. ELE133(b) Starters for 2 to 5 H.P.

A.C Motors

b. Direct on line

Starter

Starters for 2 to 5 H.P. A.C Motors

b. Direct on line Starter 2

98. ELE133(c) Starters for 2 to 5 H.P.

A.C Motorsc. Star Delta

Starter- manual, semi-

automatic and

automatic

Starters for 2 to 5 H.P. A.C Motorsc. Star Delta Starter- manual,

semi-automatic and automatic 2

99. ELE82(a) A.C. Energy Meter,

Single phase 5 amp

A.C. Energy Meter, Single phase 5 amp 1

100. DM121/

MMV151/E

LE28

Portable electric drill

Machine

Electrical drill portable machine

Drilling dia in wood : 15 mm

Drilling dia in steel : 6.5. mm

Power input : 350 w

No-load speed : 4000 rpm

Weight : 1 . 1 kgs

7

101. MMV99 Functional/experimen

t model of different

type of sensors.

Functional/experiment model of different type latest sensors.

1.Eletronic Contro Unit(ECU).

2.Crank shaft speed sensors.

3.Cam shaft Speed sensors.

4.Knock Sensors.

5.Mass Airflowsensor(MAF).

6.Oxygen sensor.

7.Manifold Absolute Pressure(MAP)sensor.

8.Throttle position sensor.

3


QTY

9.Coolant Temperature sensor.

10.Manifold Air Temperature (MAT) sensor.

11.Exhaust Oxygen Sensor.

12.Distributor Refence Pules sensor.

13.Vehicle speed sensor.

14. Battery voltage sensor.

One Each Set of 14Nos.

102. ELE73(a) Ohm Meter Series

Type

Ohm Meter Series Type 7

103. ELE73(b) Ohm Meter Shunt Type Ohm Meter Shunt Type 7

104. DM49/

MMV64

DC Ohmmeter 0 to 300

Ohms, mid scales at 20

Ohms

DC Ohmmeter 0 to 300 Ohms, mid scales at 20 Ohms 8

105. ELE74 Multi Meter (analog) 0

to 1000 M Ohms, 2.5 to

500 V

Multi Meter (analog) 0 to 1000 M Ohms, 2.5 to 500 V 6

106. DM102/

MMV130

Multimeter digital Multimeter digital 10

107. cop17 Digital Multimeters,

3.5 digit handheld

type.

Digital Multimeters, 3.5 digit handheld type. 56

108. ELE76 A.C. Voltmeter M.I. 0 –

500V A.C

A.C. Voltmeter M.I. 0 –500V A.C 1

109. ELE77 Milli Voltmeter centre

zero 100 – 0 – 100 m

volt

Milli Voltmeter centre zero 100 – 0 – 100 m volt 2

110. ELE78 D.C. Milli ammeter 0 -

500m A

D.C. Milli ammeter 0 -500m A 1

111. ELE79(a) Ammeter MC 0-5 A Ammeter MC 0-5 A 2

112. ELE79(b) Ammeter MC 0- 25 A Ammeter MC 0- 25 A 1

113. ELE80(a) A.C. Ammeter M.I. 0-5A A.C. Ammeter M.I. 0-5A 3

114. ELE80(b) A.C. Ammeter M.I. 0-25

A

A.C. Ammeter M.I. 0-25 A 1

115. DM25/

MMV28

Ammeter 300A/ 60A

DC with external shunt

Ammeter 300A/ 60A DC with external shunt 16

116. ELE81 Kilo Wattmeter 0-1-3 Kilo Wattmeter 0-1-3 kw 3


QTY

kw

117. ELE82(b) A.C. Energy Meter

Three Phase 15 amp

A.C. Energy Meter Three Phase 15 amp 4

118. ELE83 Power Factor Meter Power Factor Meter 2

119. ELE84 Frequency Meter Frequency Meter 4

120. ELE85 Flux meter Flux meter 3

121. ELE86 Wheat Stone Bridge

with galvanometer and

battery

Portable Wheatstone Bridge

designed to provide an accurate and sensitive measurement of

resistance and Locating faults in cables by adopting the

Murray and Varley Loop circuit for tests,

• Range: 0.001 ohms to 11.11 megohms.

• Constantan coil, accuracy :t 0.1 %

Galvanometer

DC mounted in beautiful Bakelite/acrylic stand with Accuracy

+2.0% F.S.D. with Lock type terminals packed in card box.

Ranges available 30-0-30, 50-0-50.

• Size M065 Top Terminals

• MR80 Deluxe Model

• MR100 (80X100) Rectangular

1

122. MMV34 Battery –charger Battery Charger : The Automatic Battery Chargers are

designed for precise charging of lead acid, sealed maintenance

free, VRLA (valve regulated lead acid) and other batteries.

These batteries require a sophisticated charger to charge

them in a precisely regulated fashion specified by the

manufacturer to avoid irreversible damage through gassing

and shortened service life. The Elak Automatic charger meets

the charging specifications of a wide range of VRLA and RG

sealed batteries very accurately. The charger delivers a

measured constant current to the battery until the

manufacturer’s specified maximum battery voltage is attained.

This voltage is then held constant for a specified period to

allow a uniform charge across all the plates. The charger may

be left connected indefinitely to a fully charged battery

without the fear of over-charging or damage.SPECIFICATIONS

- Voltage - 12 V/ 24 V / Current 0 -15 A/ 0 -10 A / End

Voltage13.8 V / 14.4 V/ 27.6 V / 28.8 V SizeL x W x H (mm)

340 x 260 x 160 11 5

123. ELE112 3- point D.C. Starter 3-point DC Starter.

3 Point D.C. Motor starter suitable to work on 5 H.P. D.C.

motor, Voltage 230/250 with a maximum 15% full load

current the starting period does not exceed 30 seconds with

under voltage and an intensions (Magnetic) over load release

device.

1

124. ELE113 4- point D.C. Starter 4-point DC Starter :-4 Point D.C. Motor starter suitable to work

on 5 H.P. D.C. motor, Voltage 230/250 with a maximum 15% 1


QTY

full load current the starting period does not exceed 30

seconds with under voltage and an intensions (Magnetic) over

load release device

125. ELE90 1 Phase Variable Auto

Transformer

2 Phase Variable Auto Transformer 1

126. ELE98 Current Transformer

415 Volt,50 Hz, CT

Ratio 150 / 5 Amp,

5VA

Current Transformer 415 Volt,50 Hz, CT Ratio 150 / 5 Amp,

5VA 1

127. ELE99 Potential Transformer

: 415 Volt,50Hz, PT

Ratio 11KV/ 110V,

10VA

Potential Transformer : 415 Volt,50Hz, PT Ratio 11KV/ 110V,

10VA 1

128. ELE123 Single phase

Transformer, core

type, air cooled 1 KVA ,

240/415 V, 50 Hz

Single phase Transformer, core type, air cooled

2KVA. 230/115V with tapping on secondary

1

129. ELE133(d) Auto Transformer type Auto Transformer type 3

130. DM202/

MMV260

Welding Transformer (

150-300 Amps)

Transformer welding set 150 amps. – continuous welding

current, with all accessories and electrode holder. step down

transformer main supply 220-440 V necessity 100-1000amp

5

Joint Director

Skill Development Sagar