e-line service configuration mop v2
DESCRIPTION
E-LINE Service Configuration MOP v2TRANSCRIPT
CONFIDETIAL Page 1 of 6
SUBJECT
E-Line Service Configuration MOP
REFERENCE NUMBER
REVISION
V 1.0 PREPARED BY:
Gilbert T. Lacanlale DATE
April 29, 2015
1. Configure the assigned slot/port/VLAN on the Ethernet Config of both sites, Save selected
to device.
2. Create a dynamic tunnel. Needed: Slot and port of source and sink site
IP config Tunnel Config Signaling: Dynamic Protection: Dynamic LSP 1:1 Protection
CONFIDETIAL Page 2 of 6
SUBJECT
E-Line Service Configuration MOP
REFERENCE NUMBER
REVISION
V 1.0 PREPARED BY:
Gilbert T. Lacanlale DATE
April 29, 2015
Click Source LSR and Sink LSR Check “enable BFD”
Check Strict Routing Click the left circle/button to create the forward main route(click the foc line then the next hop site until it reached its destination) then the right button to create the reverse main route.
CONFIDETIAL Page 3 of 6
SUBJECT
E-Line Service Configuration MOP
REFERENCE NUMBER
REVISION
V 1.0 PREPARED BY:
Gilbert T. Lacanlale DATE
April 29, 2015
CONFIDETIAL Page 4 of 6
SUBJECT
E-Line Service Configuration MOP
REFERENCE NUMBER
REVISION
V 1.0 PREPARED BY:
Gilbert T. Lacanlale DATE
April 29, 2015
Configure the protection route. Click strict routing, click left button to create forward protection route and right button to create reverse protection route. Select 10ms on path 1 and 2
Under Path 1/Path 2 BFD Properties, Select 10ms for the minimum transmit and received time.
CONFIDETIAL Page 5 of 6
SUBJECT
E-Line Service Configuration MOP
REFERENCE NUMBER
REVISION
V 1.0 PREPARED BY:
Gilbert T. Lacanlale DATE
April 29, 2015
Note: Do not forget to add Management IP on each LDP protocol mutually on each NE.
3. Create the VC. If there are four VLANs, create four VC on the existing or created tunnel. Right Click on the Tunnel, Choose Add IPRAN VC Circuit.
Details: Signaling: Dynamic Click Next Batch Creation Settings Lot Size: (Depends on the numbers of E-Line service which corresponds to the equal number of VC that must be created) Click Completed
4. Create the Eline service Go to Service Configuration >> IP Config >> L2VPN Config (L) Service Name: “ Site ID Slotand PortNumber VLAN VLAN Number Example: 3835 s2p11 VLAN 580 Next Select the site and ports Source NE: Click the source site Source Port: click the slot,port and vlan id
Sink NE: click the sink site Sink Port:click the slot
Next Choose a VC UNI must be VPWS on both sites Completed
5. Deliver the protection pair
6. Deliver the cross connect of the tunnel
7. Deliver the cross connect of the service
8. To check the service status via Secure CRT. Run these commands.
CONFIDETIAL Page 6 of 6
SUBJECT
E-Line Service Configuration MOP
REFERENCE NUMBER
REVISION
V 1.0 PREPARED BY:
Gilbert T. Lacanlale DATE
April 29, 2015
Access the Site by opening a connection via its Site NE IP. telnet 127.1 2650 password: fiberhome enable #show ldp session -> must have uptime #show mpls vc-table ->must have uptime #sh run interface GE0/3/7 #sh run interface GE0/3/7.580 #sh running-config rsvp-path >> to check your route
9. Creating a static tunnel.
Need to plan PW labels, 2 for tunnel and 2 for VC Example: 1159-1160 for tunnel and 1161-1162 for VC Service configuration > IP Config > Tunnel Config Signaling: Static Protection: depends on plan Tick Enable BFD Insert your Label.